Samsung RF267AARS, RF26DBRS1, RF267AAWP, RF26DBSH1, RF267AASH Service Manual

BOTTOM MOUNT FREEZER

BASIC : RF267AA

MODEL NAME : RF267AARS RF26DBRS1

RF267AABP RF26DBBP1
RF267AAWP RF26DBSH1
RF267AASH

MODEL CODE : RF267AARS/XAA RF26DBRS1/SML

RF267AABP/XAA RF26DBBP1/SML
RF267AAWP/XAA RF26DBSH1/SML
RF267AASH/XAA RF26DBRS1/XSA

REFRIGERATOR

REFRIGERATOR CONTENTS

1. PRECAUTIONS(SAFETY WARNINGS) 4

2. PRODUCT SPECIFICATIONS

7

3. DISASSEMBLY AND REASSEMBLY

21

4. TROUBLESHOOTING

47

5 . EXPLODED VIEW & PARTS LIST

85

6. PCB DIAGRAM

123

7. WIRING DIAGRAM

128

8. SCHEMATIC DIAGRAM

129

Asia : http://asia.samsungportal.com)

RF267/26DB

For the latest parts information, Please access to our service web site

North America : http://service.samsungportal.com Europe : http://europe.samsungportal.com

(

IMPORTANT SAFETY NOTICE

The service guide is for service men with adequate backgrounds of
electrical, electronic, and mechanical experience. Any attempt to repair
a major appliance may result in personal injury and property damage.
The manufacturer or dealer cannot be responsible for the interpretation
of this information.

SAMSUNG ELECTRONICS AMERICA, INC.

Technical Service Guide

Copyright ⓒ2008

All rights reserved. This service guide may not be reproduced in whole or in
part in any form without written permission from the SAMSUNG ELECTRONICS
Company.

WARNING

Contents

1. PRECAUTIONS(SAFETY WARNINGS) 4

2. PRODUCT SPECIFICATIONS 7
2-1) INTRODUCTION OF MAIN FUNCTION 8
2-2) SPECIFICATIONS 11
2-3) INTERIOR VIEWS 12
2-4) MODEL SPECIFICATION 13
2-5) MODEL SPECIFICATION &SPECIFICATION CHART 14
2-6)DIMENSIONS OF REFRIGERATOR (INCHES) 17
2-7) OPTIONAL MATERIAL SPECIFICATION 18
2-8) REFRIGERANT ROUTE IN REFRIGERATION CYCLE 19
2-9) COOLING AIR CIRCULATION 20

3. DISASSEMBLY AND REASSEMBLY 21
3-1) PRECAUTION 22
3-2) REFRIGERATOR DOOR 23
3-3) DOOR SWITCH IN REFRIGERATOR 25
3-4) DOOR GASKET 25
3-5) DOOR HANDLE 25
3-6) REFRIGERATOR LIGHT 26
3-7) COVER-DISPLAY & WATER-DISPENSER 26
3-8) WATER-DISPENSER 27
3-9) GLASS SHELF 28
3-10) FOLDABLE GLASS SHELF 29
3-11) VEGETABLE & FRUIT DRAWERS SHELF 29
3-12) COOL SELECT PANTRY 30
3-13) WATER TANK 31
3-14) MOTOR DAMPER 33
3-15) WATER FILTER (DISASSEMBLY) 33
3-16) WATER FILTER (REASSEMBLY) 34
3-17) GALLON DOOR BIN 34
3-18) VERTICAL HINGED SECTION 35
3-19) EVAPORATOR COVER IN REFRIGERATOR 36
3-20) EVAPORATOR IN REFRIGERATOR 37
3-21) FREEZER DOOR 38
3-22) PULL OUT DRAWER 39
3-23) ICE-MAKER 40
3-24) FREEZER LIGHT 41
3-25) DOOR SWITCH IN FREEZER 41
3-26) EVAPORATOR COVER IN FREEZER 42
3-27) EVAPORATOR IN FREEZER 42
3-28) MACHINE COMPARTMENT 43
3-29) ELECTRIC BOX 46

4. TROUBLESHOOTING 47
4-1) FUNCTION FOR FAILURE DIAGNOSIS 48

4-1-1. TEST MODE (MANUAL OPERATION / MANUAL DEFROST FUNCTION)

48

4-1-2. DISPLAY FUNCTION OF COMMUNICATION ERROR

49

4-1-3. SELF-DIAGNOSTIC FUNCTION

50
4-1-4. DISPLAY FUNCTION OF LOAD CONDITION 53
4-1-5. EXHIBITION MODE SETTING FUNCTION 54
4-1-6. OPTION SETTING FUNCTION 54

Contents

4-1-7. OPTION TABLE 57

4-2) DIAGNOSTIC METHOD ACCORDING TO THE TROUBLE SYMPTOM(FLOW CHART) 59

4-2-1. IF THE TROUBLE IS DETECTED BY SELF-DIAGNOSIS 60
4-2-2. IF FAN DOES NOT OPERATE 70
4-2-3. IF ICE ROOM FAN DOES NOT OPERATE 71
4-2-4. IF ICE MAKER DOES NOT OPERATE 72
4-2-5. IF DEFROST DOES NOT OPERATE (F,R DEF HEATER) 73
4-2-6. IF POWER IS NOT SUPPLIED 74
4-2-7. IF COMPRESSOR DOES NOT OPERATE 75
4-2-8. WHEN ALARM SOUND CONTINUOUS WITHOUT STOP(RELATED WITH BUZZER SOUND) 76
4-2-9. IF PANEL PCB DOES NOT WORK NORMALLY 78
4-2-10. IF PANTRY PANEL PCB IS NOT WORKING NORMALLY 79
4-2-11. WHEN REFRIGERATOR ROOM LAMP DOES NOT LIGHT UP 80
4-2-12. IF ICE WATER IS NOT SUPPLIED 81
4-2-13. IF WATER IS NOT SUPPLIED 82
4-2-14. IF CUBED OR CRUSHED ICE IS NOT SUPPLIED 83
4-2-15. IF COVER ICE ROUTE MOOR(GEARD MOTOR) IS NOT WORKING NORMALLY 84

5 . EXPLODED VIEW & PARTS LIST 85

5-1) FREEZER 86
5-2) REFRIGERATOR 89
5-3) CABINET 93
5-4) DISASSEMBLY OF FREEZE DOOR 97
5-5) DISASSEMBLY OF REFRIGERATOR DOOR LEFT 99
5-6) DISASSEMBLY OF REFRIGERATOR DOOR RIGHT 102

6. PCB DIAGRAM 123
6-1) PCB LAYOUT WITH PART POSITION 124
6-2) PCB LAYOUT WITH PART POSITION (SMPS BOARD) 125
6-3) CONNECTOR LAYOUT WITH PART POSITION (MAIN BOARD) 126
6-4) CONNECTOR LAYOUT WITH PART POSITION (SMPS OARD) 127

7. WIRING DIAGRAM 128

8. SCHEMATIC DIAGRAM 129
8-1) WHOLE BLOCK DIAGRAM 129
8-2) CIRCUIT DIAGRAM 130

4

1. PRECAUTIONS(SAFETY WARNINGS)

●

Pull the power plug out before for the change or repair of electric parts.

→

Be careful the electric shock.

●

When exchanging the parts, use the correct parts.

→

Check the model name, rating voltage, rating current, running

temperature symbols.

●

When troubleshooting, connect firmly the types of harness.

→

Make not to be separated when some power is imposed.

●

Check the traces of water infiltration at the electric parts.

→

If there is a trace of water infiltration, exchange or tape the parts.

●

Check the assemble status of parts after troubleshooting.

→

It should be done indiscriminately as before the repair.

●

Check the use circumstance of refrigerator.

→

If the refrigerator is installed at the place that is damp or wet, or

status of installation is unstable, change the installation place.

●

Do earth in case of need.

→

Particularly, Be sure to earth when there is a risk of an electric

leakage by humidity or wetness.

●

Do not use multi plugs in a plug socket at the same time.
Check if the power cord and socket is damaged, pressed, squeezed,
or fired.

→

If the plug or plug socket is damaged, repair or exchange that

immediately.

●

Do not allow consumers to repair the appliance by themselves.

●

Do not store other materials except the foods.

→

Drugs or scientific materials : difficult to keep precise temperature.

→

The inflammables(alcohol, benzene, ether, LP gas, butane gas etc.):

have risk of explosion.

5

PRECAUTIONS(SAFETY WARNINGS)

Read all instructions before repairing the product and follow the instructions
in order to prevent danger or property damage.

CAUTION/WARNING SYMBOLS DISPLAYED

SYMBOLS

Indicates that a
danger of death
or serious injury
exists.

Indicates that a risk
of personal injury
or material damage
exists.

means “Prohibited”.

means “Do not disassemble”.

means “No contact”.

means ”Warning or Caution”.

means “Earth or Ground”.

means “Unplug the unit before
preforming service”

Pull the power plug out to
exchange the interior lamp
of the refrigerator.

●

It may cause electric shock.

Warning

Warning & Caution

Caution

Unplug

Use the rated components
on the replacement.

●

Check the correct model, rated
voltage, rated current, operating
temperature and so on.

On repair, make sure that the
wires such as harness are
bundled tightly.

●

Bundle tightly wires in order not to be
detached by the external force and then not
to be wetted.

Check if there is any trace
indicating the permeation
of water.

●

If there is that kind of trace, change

the related components or do the

necessary treatment
such as taping
using the
insulating tape.

After repair, check the
assembled state of components.

●

It must be in the same assembled state
when compared with the state before
disassembly.

On repair, remove completely dust
or other things of housing parts,
harness parts, and check parts.

●

Cleaning may prevent the possible fire by

tracking or short.

Rated

components

6

PRECAUTIONS(SAFETY WARNINGS)

❈

Please let users know following warnings & cautions in detail.

Do not allow users to put bottles or
kinds of glass in the freezer.

●

Freezing of the contents may inflict a wound.

Do not allow users to store narrow
and lengthy bottles or foods in a
small multi-purpose room.

●

It may hurt you when refrigerator door is
opened and closed resulting in falling stuff
down.

Do not allow users to store
pharmaceutical products, scientific
materials, etc., in the refrigerator.

●

The products which temperature control
should not be stored in the refrigerator.

Do not allow users to store
articles on the product.

●

Opening or closing the door may cause
things to fall down, which may cause
injury.

Prohibition

Warning & Caution

Do not allow users to
disassemble, repair or alter.

●

It may cause fire or abnormal

operation which leads to injury.

Do not

disassemble

Do not allow users to insert the
power plugs for many products
at the same time.

●

May cause abnormal generation of

heat or fire.

Prohibition

Do not allow users to bend the
power cord with excessive force
or do not have the power cord
pressed by heavy article.

●

May cause fire.

Do not allow users to install the
refrigerator in the wet place or
the place where water splashes.

●

Deterioration of insulation of electric

parts may cause electric shock or fire.

Make sure of the earth.

●

Be sure the product is properly grounded.

Earth

7

2. PRODUCT SPECIFICATIONS

2-1) INTRODUCTION OF MAIN FUNCTION 8

2-2) SPECIFICATIONS 11

2-3) INTERIOR VIEWS 12

2-4) MODEL SPECIFICATION 13

2-5) MODEL SPECIFICATION &SPECIFICATION CHART 14

2-6)DIMENSIONS OF REFRIGERATOR (INCHES) 17

2-7) OPTIONAL MATERIAL SPECIFICATION 18

2-8) REFRIGERANT ROUTE IN REFRIGERATION CYCLE 19

2-9) COOLING AIR CIRCULATION 20

8

2. PRODUCT SPECIFICATIONS

●●

A newly Developed SAMSUNG bottom mount freezer in 2008 has the following
characteristics.

Surround Multi Flow

●●

Uniform cooling for each shelf and even in corner in fresh
food compartment by centerpositioned fan and duct with
multiple flow effluences

Twin Cooling System

●●

The refrigerator and the freezer have two evaporators.
Given this independent system, the freezer and the
refrigerator are cooled individually as required and are,
therefore, more efficient.
Food odor from the refrigerator does not affect food in the
freezer due to separate air flow circulation.

Electronic control from outside of Pantry Cover

●●

Adjustable temperature control ((around 41 (5 ) : Deli /
around 38

(3 ) : Fresh / around 34 (1 ) Chilled )
Temperature control from outside of the Pantry : user
friendly design helps keep foods fresh for longer

16" Pizza Corner

●●

Can be used for 16" pizza if stand flip tilting pocket.

Ice and Water Dispenser

●●

The ice and water dispenser provides ice and cold water at
any time.

Secure Auto Close Door System

●●

Secure Auto Close Door System

●●

Cool tight doors

●●

Energy saving

●●

Preventing sweat on fridge doors

2-1) Introduction of main function

9

2. PRODUCT SPECIFICATIONS

1

2

3

4

5

6

Display

Pantry

Shelf

Drawer

Ice Maker

Dispenser

Display panel is on the
door to use the Ice &
Water Dispenser more
convenient.

Adding “Deli” mode to
store the foods fresher.

Slide Out Shelf is
adopted to store the
foods more convenient.

The right Vegetable
drawer can be fully taken
out even the left door is
closed.

Compact Ice Maker is
installed for the Ice &
Water Dispenser.

Dispenser provides
water, ice or iced water.

NO Item Details

Display on Top Table Display on Door

Basic Model(RF265AA) New Model(RF26DB**)

Changing Items

10

2. PRODUCT SPECIFICATIONS

1

2

This shelf is attached on the left side of cabinet
and can be folded. This design improves the
space utilization.

Foldable

Shelf

Quick Space

Shelf

The half of this shelf can be slid in.
This design secures enough space to store tall
things.

NO Item Details of New Items

New Model(RF26DB**)

N

11

2-2) Specifications

PRODUCT SPECIFICATIONS

Defrost Control From 24 to 32 hrs
Thermo Bimetal Protector 140°F(60

)(off) 104°F(40 )(on)

Defrost Thermistor(502AT) 50°F(10

)(off)
Electrical Rating AC115V 60Hz 11.6 Amps / 220V~240V 50Hz
Maximum Current Leakage 0.25 mA
Maximum Ground Path Resistance 0.1 Ohm
Energy Consumption 570KWh/year

Ambient Temperature 70

℉(21 ) 90℉(32 )
Refrigerator,℉ 34℉(1 )∼46℉(8 ) 34℉(1 )∼46℉(8 )
Freezer,℉ -14℉(-26

)∼8℉(-13 ) -14℉(-26 )∼8℉(-13 )

Run Time,% 󳠞40 󳠞60

Refrigerant Charge (R134a) 5.64 oz(160g)
Compressor((MK172D-R2U) 897 Btu/hr(0.263kw)
Compressor oil Freol α-10
Capillary tube(Dia, Length) 0.032

＂＂

,118

＂＂((00..8811mmmm,,22999977mmmm))

Dryer Molecular Sieve XH-9

Clearance must be provided for air circulation
AT TOP 1

＂＂ ((2255mmmm))

AT SIDES 0.5

＂＂ ((1155mmmm))

AT REAR 1

＂＂ ((2255mmmm))

Fan

Fan

(Air inlet)(Air inlet)

Heat exchanger

Compressor

C-Fan Noise FilterDryer

Sub-condenser Water Valve

ELECTRICAL SPECIFICATIONS

Freezer

Refrigerator

NO LOAD PERFORMANCE

REFRIGERATION SYSTEM

INSTALLATION

FanFan

(Air inlet)(Air inlet)(Air inlet)(Air inlet)

FanFan

Heat exchangerHeat exchanger

FanFan

Heat exchanger

(Air inlet)(Air inlet)

12

PRODUCT SPECIFICATIONS

2-3)

Interior Views

Freezer

Refrigerator

Auto Door Closer

Water Filter

Dairy Compartment

Door Bins

Cool Select Pantry

TM

Light

Vertical Hinged

Section

Vegetable & Fruit

Drawers

Tilting Pocket

Light

Pull Out Drawer

Freezer Drawer Bin

Slide-Shelf

Quick-Space

Glass Shelf

Ice-Maker

Foldable-Shelf

Slide-Shelf

13

2-4) Model Specification

PRODUCT SPECIFICATIONS

F-Room

R-Room

F-Room

R-Room

F-Room

R-Room

F-Room

R-Room

N-N

Sound power level

Sound Pressure level

Cooling

Speed(Min)

Product Zone

Appearance

ITEM SPEC

89.6 (32°C)

109.4 (43°C)

Temperature

Distribution

(Fridge)

Operation rate

Performance

Noise

Cooling Tech

Door Shape

Special Room

250

250

-26.0

2.0

-18.0

5.0

2.0

2.0

60%

46dB

45dB

SAMSUNG

RF267AA/RF26DB

Twin Cooling

Contour

Cool Select Pantry

209.8

201.8

-28.7

1.0

-21.9

1.1

0.1

0.2

54.0

42.9

41.2

MAYTAG

MFI2568AES

Mono Cooling

Contour

Pantry

246

575

-27.2

1.6

-20.9

5.9

0.6

1.1

60.7

47.0

48.2

LG

LFX25960ST

Mono Cooling

Contour

Pantry

224

232

-28.8

-1.8

-22.5

0.8

1.3

0.5

56.5

41.7

40.1

COLOR

ModelITEM

14

2-5) Model Specification &Specification Chart

PRODUCT SPECIFICATIONS

External size

Net

Capacity

Weight

Packing

D

H

W

Efficiency of volume

On Cabinet
W/O Handle
With Handle

W/O Hinge Cap
With Hinge Cap

Total

Freezer

Refrigerator

Set

Packing

Width

Depth

Height

Black

Real STS

White

Platinum STS

Cabinet (Both sides of Embo)

All Black

Noble STS

Snow White

Noble STS

Door

Empire Black

Versailles Stainless

Snow White

Stainless Platinum

Molding

I Black

Creamy STS

Snow White

Creamy STS

Compressor

Rated Frequency and Frequency

Refrigerant

Foaming agent

Refrigerant Input Amount

Kind of Refrigerator

Motor Rated Consumption Power

Electric Heater Rated Consumption Power

RF267AA / RF26DB

Ice & Water Dispenser with Pantry

35.7 inch (908mm)

29.1 inch (740mm)

32.9 inch (836mm)

35.6 inch (905mm)

68.6 inch (1744mm)

69.8 Inch (1778mm)

25.5Cu.ft (722.1 )

8.2Cu.ft (230.6 )

17.3Cu.ft (491.5 )

50.17%
330 Pounds (150kg)
363 Pounds (165kg)

38.6 Inch (980mm)

39.4 Inch (1001mm)

75.7 Inch (1923mm)

reciprocate

AC 115V/60Hz / AC 230V 50Hz

R 134a

C-Pantane

5.64 oz (160g)

Indirect Cooling Method Refrigerator

140A

380W

Items

Model

15

2-5) Model Specification &Specification Chart

PRODUCT SPECIFICATIONS

Compressor

Evaporator

Model

First Defrost Cycle (Concurrent defrost of F and R)

Defrost Cycle(FRE)
Defrost Cycle(REF)

Pause time

THERMISTOR

(F-SENSOR)

502AT

Temperature Selection

-14 (-26 )

-2 (-19 )
8 (-13 )

Model

THERMISTOR

(R-SENSOR)

502AT

F Defrost-Sensor

R Defrost-Sensor

F Bimetal-thermo

Protector

R Bimetal-thermo

Protector

Temperature Selection

34 (1 )
38 (3 )
46 (8 )

Model
SPEC
Model
SPEC
Rated

Operating temperature

Rated

Operating temperature

Condenser

Dryer

Capillary tube(Dia x Length)

Refrigerant

Model

Starting type

Oil Charge

Freezer

Refrigerator

MK172D-R2U / MK190QL2U

R.S.C.R

FREOL - 10
SPLIT FIN TYPE
SPLIT FIN TYPE

Forced and natural convection type

Molecular sieve XH-9

0.032” x 118” (0.81mm x 2997mm)
R134a

6hr 10min

12~23hr(vary according to the conditions used)

6~11hr(vary according to the conditions used)

12 1min

THERMISTOR (502AT)

5.0 at 77 (25 )

THERMISTOR (502AT)

5.0 at 77 (25 )

AC 125V 10A / AC 250V 3A

Off : 140 (60 ) / On : 104 (40 )

AC 125V 10A / AC 250V 3A

Off : 140 (60 ) / On : 104 (40 )

ON( )

-11 (24 )
1 (-17 )

11 (-12 )

ON( )
36 (2 )
40 (4 )
48 (9 )

OFF( )

-17 (-27 )

-5 (-21 )
5 (-15 )

OFF( )
32 (0 )
36 (2 )
44 (7 )

Specification

RF267AA / RF26DB

Components for FreezerDefrost Related Components

FreezerRefrigeratorDefrost Cycle

Defrost SensorBimetal

Room Temperature Sensor Components

16

PRODUCT SPECIFICATIONS

Items

Model

Defrost Heater(FRE)
Defrost Heater(REF)

DISPENSER Heater

FRENCH Heater
ICE Duct Heater

Water Tank Heater

Interlock with French Heater

-

Interlock with Defrost Heater (FRE)

-

Running

Starting

Model

Operation

Model

Temp.ON

Temp.OFF

Condenser for COMP

(Package type)

Starting-Relay

Over load Relay

Rated Voltage

MOTOR-BLDC(FRE)

MOTOR BLDC(ICE ROOM)

MOTOR-BLDC(REF)

MOTOR-BLDC(CIRCUIT)

MOTOR-DAMPER(PANTRY)

Lamp(FRE)
Lamp(REF)

Conducting af F Defrost

Conducting at R Defrost

Door Switch

FRE
REF

REF(ICE ROOM)

Power cord

Earth Screw

Bimetal thermo For Preventing Overheating of Refrigerator Lamp

AC 115V, 240W / AC 230V, 240W

AC115V, 120W / AC 230V, 120W

AC115V, 3W / AC 230V, 3W

AC115V, 10W / AC 230V, 10W

AC115V, 4W / AC 230V, 4W

DC 12V, 2W

AC125V 10A / AC250V 3A Off: 140 (60 )/ On : 104 (40 )

12 ,250V / 5 ,450V

-

J531Q33E100M200-2

10 20%

4TM435RFBYY-53

266 41 130 5

141.8 48.2 61 9

AC 115V/60Hz / 220~240V/50Hz

DC12V / FDQT06SS3

DC12V / DREP5020LB

DC12V / FDQT06SS3
DC12V / FDQT04SS2

DC12V / NSBY001TA1
AC 120V / 60W(1EA) / AC 230V 40W(1EA)
AC 120V / 60W(2EA) / AC 230V 60W(2EA)

AC 125V 1.5A (1EA) / AC 250V 0.5A

DC200V 1.5A / MS-406-SS-01(2EA)

125~250V /11A, EMB606

AC125V 15A / AC 250V 10A

BSBN (BRASS SCREW)

Specification

RF267AA / RF26DB

Electric Components

17

PRODUCT SPECIFICATIONS

29.1"(739mm)

3.4"(86mm)

21.6"(549mm)41.7"(1059mm)

0.6"(15mm)

69.8"(1778mm)

1.3"(34mm)

32.9"(836mm)

35.6"(905mm)

35.7"(908mm)

24.3"(617mm)

3.4"(86mm)

54.5"(1384mm)

18.7"(475mm)

47.8"(1214mm)

2-6)Dimensions of Refrigerator (Inches)

18

PRODUCT SPECIFICATIONS

2-7) Optional Material Specification

Part Name

FILTER

WATER-ASSY

DA29-00003B

ASSY-PACKING

SUB

DA99-00240G

LAMP INCANDENT

4713-001223

Part Code AMOUNT

1

1

3

AMOUNT

1

1

3

Part Name

ASSY-INSTALL FILTER

DA97-01469W

PIPE-CONNECT

WATER PACKING

DA62-01329A

LAMP INCANDENT

4713-001232(REF) : 60W
4713-001201(FRE) : 40W

Part Code

RF267AA

RF26DB

19

Compressor → Sub-condenser → Hot Pipe → Dryer → Capillary Tube → Refrigerator Evaporator → Freezer
Evaporator→ Suction Pipe → Compressor

Refrigerator
Evaporator

Freezer
Evaporator

Suction Pipe

Capillary Tube

Accumulator

Compressor

Sub Condenser

Hot Pipe

Muffler

PRODUCT SPECIFICATIONS

2-8) Refrigerant Route in Refrigeration cycle

20

Refrigerator

PRODUCT SPECIFICATIONS

2-9) Cooling Air Circulation

Freezer

21

3. DISASSEMBLY AND REASSEMBLY

3-1) PRECAUTION 22

3-2) REFRIGERATOR DOOR 23

3-3) DOOR SWITCH IN REFRIGERATOR 25

3-4) DOOR GASKET 25

3-5) DOOR HANDLE 25

3-6) REFRIGERATOR LIGHT 26

3-7) COVER-DISPLAY & WATER-DISPENSER 26

3-8) WATER-DISPENSER 27

3-9) GLASS SHELF 28

3-10) FOLDABLE GLASS SHELF 29

3-11) VEGETABLE & FRUIT DRAWERS SHELF 29

3-12) COOL SELECT PANTRY 30

3-13) WATER TANK 31

3-14) MOTOR DAMPER 33

3-15) WATER FILTER (DISASSEMBLY) 33

3-16) WATER FILTER (REASSEMBLY) 34

3-17) GALLON DOOR BIN 34

3-18) VERTICAL HINGED SECTION 35

3-19) EVAPORATOR COVER IN REFRIGERATOR 36

3-20) EVAPORATOR IN REFRIGERATOR 37

3-21) FREEZER DOOR 38

3-22) PULL OUT DRAWER 39

3-23) ICE-MAKER 40

3-24) FREEZER LIGHT 41

3-25) DOOR SWITCH IN FREEZER 41

3-26) EVAPORATOR COVER IN FREEZER 42

3-27) EVAPORATOR IN FREEZER 42

3-28) MACHINE COMPARTMENT 43

3-29) ELECTRIC BOX 46

22

ASSEMBLY & DISASSEMBLY

• Unplug the refrigerator before cleaning and making repairs.

• Do not dissemble or repair the refrigerator by yourself.

- You run risk of causing a fire, malfunction and/or personal injury.

• Remove any foreign matter or dust from the power plug pins.

- Otherwise there is a risk of fire.

• Do not use a cord that shows cracks or abrasion damage along its length or at either end.

• Do not plug several appliances into the same multiple power board. The refrigerator should always be
plugged into its own individual electrical which has a voltage rating that matched the rating plate.

- This provides the best performance and also prevents overloading house wiring circuits, which could
cause a fire hazard from overheated wires.

• Do not install the refrigerator in a damp place or place where it may come in contact with water.

- Deteriorated insulation of electrical parts may cause an electric shock or fire.

• The refrigerator must be grounded.

- You must ground the refrigerator to prevent any power leakages or electric shocks caused by current
leakage from the refrigerator.

• Do not put bottles or glass containers in the freezer.

- When the contents freeze, the glass may break and cause personal injury.

• Do not store volatile or flammable substances in the refrigerator.

- The storage of benzene, thinner, alcohol, ether, LP gas and other such products may cause
explosions.

- NEED TOOL

3-1) PRECAUTION

IMAGE ITEM USE

Phillips Head Driver

Use for assembling and

disassembling of screw

Flat Head Driver

Use for assembling and disassembling

of HomeBar, Dispenser, Deli

Cartessen Box, Main PBA etc...

Hex Wrench Ø2mm

Use for assembling and
disassembling of Handle

Socket Wrench Ø10mm

Use for assembling and

disassembling of Door Hinge

23

3-2) Refrigerator Door

DISASSEMBLY AND REASSEMBLY

Refrigerator

Door

Part Name How To Do Descriptive Picture

1. With the door opened, remove
the Top Table cap(

) with a Flat
head screwdriver, and close the
door.

2. Remove the 3 screw holding
down the Top Table and remove
the Top Table(

).

3. Disconnect the electrical
connector(

) above the upper
right door hinge and the 3
electrical connectors( ) above
the upper left door hinge.
Disconnect the water tube( ) by
pulling the tube fitting( ) apart
as shown in the picture.

4. Remove the 3 hex head bolts(

)
found attatched to the upper left
and right door hinges with a
Wrench(10mm).
With a Philips head screwdriver,
remove the ground screw( ) found
attatched to the upper left and right
door hinges. Remove the upper left
and right door hinges( ).

24

DISASSEMBLY AND REASSEMBLY

Refrigerator

Door

Part Name How To Do Descriptive Picture

5. Lift the door straight up to
remove.

6. With a Philips head screwdriver,
remove the two screws (

)
attatched to the lower left and
right door hinges.
With a Wrench(10mm), remove
the 2 hex head bolts(

)
attatched to the lower left and
right door hinges.
Remove the lower left and right
door hinges(

).

25

3-3) Door Switch In Refrigerator

DISASSEMBLY AND REASSEMBLY

3-4) Door Gasket

3-5) Door Handle

Door Switch

In Refrigerator

Part Name How To Do Descriptive Picture

1. Remove the magnet switch with
using a flat-blade(-) screwdriver.
(Refer to the picture)

Door Gasket

In Refrigerator

Part Name How To Do Descriptive Picture

1. Remove the door-gasket by
pulling it out of the retaining
channel.

Door Handle

Refrigerator

Door Handle

Freezer

Part Name How To Do Descriptive Picture

1. Remove the door handle of
refrigerator by lifting it up and
pulling it out.
(Refer to the picture)

1. Remove the door handle of
freezer by pushing it to the right
and pulling it out.
(Refer to the picture)

26

DISASSEMBLY AND REASSEMBLY

3-6) Refrigerator Light

3-7) Cover-display & water-dispenser

Cover-display

Part Name How To Do Descriptive Picture

1. Insert a flat-blade screwdriver

on the slot as shown in the
picture, and unlock the tabs.

2. Remove the display cover by

pushing it to the right side and
pulling it up.

3. Disengage the housing connect

of display cover

Refrigerator

Light

Part Name How To Do Descriptive Picture

1. Remove the light cover by

pulling it down with pushing the
rear of light cover.

2. Remove the lamp by turning it

counterclockwise.

①

②

27

DISASSEMBLY AND REASSEMBLY

Cover-display

Part Name How To Do Descriptive Picture

4. Remove 4 screws of cover­display

3-8) Water-dispenser

Water-dispenser

Part Name How To Do Descriptive Picture

1. Disengage the 3 Housing
Connect.

2. Remove 2 screws of the
CaseIce,Route Assy.

3. Pull the Case-Ice,Route Assy.

4. Push the hook and remove the
Micro Switch.

28

DISASSEMBLY AND REASSEMBLY

Water-dispenser

Part Name How To Do Descriptive Picture

1. Assembly shall be the contrary

order from the disassemble.
Case-Rce and Route shall be
assembled inside of hose.
Otherwise, assemble cannot be
accomplished.

2. When assembling Cover-

Display, first insert it from
leftside and then assemble to
rightside.
Otherwise, the tab can be
broken.

3-9) Glass Shelf

Glass Shelf

Part Name How To Do Descriptive Picture

Remove the shelf by lifting the
front plane of the shelf up and
pulling it out.

hose

29

DISASSEMBLY AND REASSEMBLY

3-11) Vegetable & Fruit Drawers Shelf

3-10) Foldable Glass Shelf

Foldable Glass

Shelf

Part Name How To Do Descriptive Picture

Remove 2 screws of the Fold
Glass Shelf

Vegetable & Fruit

Drawers Shelf

Part Name How To Do Descriptive Picture

1. Remove the vegetable & fruit
drawer by pulling the roller part
and lifting it up.

2. Remove the vegetable & fruit
drawers shelf by pulling it out.
(Refer to the picture)

30

DISASSEMBLY AND REASSEMBLY

3-12) Cool Select Pantry

Cool Select Pantry

Part Name How To Do Descriptive Picture

1. Remove the cool select pantry

by pulling the roller part and
lifting it up.

Cool Select Pantry

Cover

1. Remove the cool select pantry

cover by lifting the central part
of the cover while pushing it to
the left.

Cool Select Pantry

Shelf

1. Remove the cool select pantry

shelf by lifting the front part of
the shelf while pulling it.

Cool Select Pantry

Rail

1. Remove the cool select pantry

rail by unscrewing the 3 screw
parts and pulling the rail.

2. Disconnect the housing

connector from the internal rail
part.
(Refer to the picture)

31

DISASSEMBLY AND REASSEMBLY

3-13) Water Tank

Water Tank

Part Name How To Do Descriptive Picture

The Water Tank is located in the
lower part of the fridge. Before
disassembling the Water Tank take
out shelf and drawers and pantry
located in front of the Water Tank.

1. Remove 2 screw of the Water
Tank cover.

2. Disengage the housing
connector.

3. Remove the 2 screws attached
to the Water Tank heater.
Remove the Water Tank heater.

4. Remove the 2 screws attached
to the Water Tank.
Remove the Water Tank cover.

32

3-13) Water Tank

DISASSEMBLY AND REASSEMBLY

Water Tank

Part Name How To Do Descriptive Picture

One water Tube is located in the
machine compartment of the
refrigerator. Before disassembling
the Water Tube, take out the
compressor cover.

5. Remove the water valve fixed by

the screw.

6. Disconnect the water tube by

pushing the tube fitting apart as
shown in the picture.

The other Water Tube is located in
the Top Table of the refrigerator.
Before disassembling the Water
Tube, take out the Top table.

7. Disconnect the Water Tube by

pushing the tube fitting apart as
shown in the picture.

8. Remove the Water Tank by

pulling the Water Tube.

33

DISASSEMBLY AND REASSEMBLY

3-14) Motor Damper

3-15) Water Filter (Disassembly)

Motor Damper

Part Name How To Do Descriptive Picture

1. Remove the cool select pantry.
Remove the screw part of lower
motor damper part and then
push the motor damper down.

2. Disengage 2 housing
connectors from the rear motor
damper.
(Refer to the picture)

Water Filter

Part Name How To Do Descriptive Picture

1. Remove the shelf by lifting the
front plane of the shelf up and
pulling it out.

2. Remove the water filter by
turning it clockwise.
(Refer to the picture)

34

DISASSEMBLY AND REASSEMBLY

3-16) Water Filter (Reassembly)

3-17) Gallon Door Bin

Gallon Door Bin

Part Name How To Do Descriptive Picture

1. Remove the gallon door bin by
lifting it up.
(Refer to the picture)

Water

Filter

Part Name How To Do Descriptive Picture

1. Place the part of ( ) arrow (that
is indicating in the picture) in the
middle of the front filter cover
and push it up.

2. Turn the water filter
counterclockwise until central
horizontal line of filter cover and
both ends of water filter label
are made all of the same width.
(Refer to the picture.)

35

DISASSEMBLY AND REASSEMBLY

3-18) Vertical Hinged Section

Vertical Hinged

Section

Part Name How To Do Descriptive Picture

1. Remove 2 screw cap parts with

a flat-blade(-) screwdriver.
(Refer to the picture)

2. Unscrew 2 screws.

3. Disengage the internal housing

connector of the vertical hinge.

4. Remove the vertical hinged

section by lifting the vertical
hinge up.
(Refer to the picture)

36

DISASSEMBLY AND REASSEMBLY

3-19) Evaporator Cover In Refrigerator

Evaporator Cover

In Refrigerator

Part Name How To Do Descriptive Picture

1. Remove the angle cap with a
flat-blade screwdriver.
(Refer to the picture)

2. Unscrew 4 screws.

3. Remove the the lower part of
angle mid by pulling it out and
pushing it down.
(Refer to the picture)

4. Remove the hook by pulling it
from the lower part and pushing
the cover down.
(Refer to the picture)

5. Disconnect the housing
connector of the rear plane.
(Refer to the picture)

37

DISASSEMBLY AND REASSEMBLY

3-20) Evaporator In Refrigerator

Evaporator

In Refrigerator

Part Name How To Do Descriptive Picture

1. Remove the the housing cover

by pushing both lateral sides of
the housing cover and pulling it
out.
(Refer to the picture)

2. Disconnect the housing

connector part.
(Refer to the picture)

3. Unscrew 2 screws.

4. Remove the evaporator by lifting

the bottom side of it up and
pulling it out.
(Refer to the picture)

38

DISASSEMBLY AND REASSEMBLY

3-21) Freezer Door

Freezer

Door

Part Name How To Do Descriptive Picture

1. Pull the drawer open to full
extension.

2. Remove the tilting Pocket( ) by
pulling the both brackets( )
upward at the same time.

3. Take out the lower basket( ) by
lifting the basket up from rail
system.

4. Remove a fixing pin( ) and
remove a shaft( ) by pushing it
to the right side with your hand.

5. Separate the rail from the rail
cover by pushing the hooks (

)
in on both sides of the rail. After
pusing the hooks in, remove the
drawer by pulling towards you
with both hands.

①

②

③

⑤

④

⑥

39

DISASSEMBLY AND REASSEMBLY

3-22) Pull Out Drawer

Pull Out Drawer

Part Name How To Do Descriptive Picture

1. Slide the drawer out as much as
possible.

2. Insert a flat screw driver(-) into
the gap and then push it up to
diassemble.

3. Remove the pull out drawer by
lifting the bottom part of drawer
bin and pulling it out.

40

3-23) Ice-Maker

DISASSEMBLY AND REASSEMBLY

Ice Maker

Part Name How To Do Descriptive Picture

2. Remove 1 screw of the Cover

1. Pull the Ice-Bucket lever and out

3. Disassemble the cover with a
flat-blade(-) screwdriver and pull
it out.

4. Disengage the 2 housing
connector.

5. Push hook and pull the Ice­Maker out.

6. To disassemble, push the tab
and pull the case-auger and the
motor out.

lever

41

DISASSEMBLY AND REASSEMBLY

3-24) Freezer Light

3-25) Door Switch In Freezer

Door Switch In

Freezer

Part Name How To Do Descriptive Picture

1. Remove the freezer drawer bin
by using a flat-blade(-)
screwdriver.(Refer to the
picture)

2. Disconnect the housing
connector part.

Freezer Light

Part Name How To Do Descriptive Picture

1. Remove the light by pulling the
light cover down while pushing
the rear plane of light cover.

42

DISASSEMBLY AND REASSEMBLY

3-26) Evaporator Cover In Freezer

3-27) Evaporator In Freezer

Evaporator In

Freezer

Part Name How To Do Descriptive Picture

1. Remove the housing cover by
pushing both lateral sides of
housing cover part and pulling it
out.
Remove the housing connector
part.

2. Remove the evaporator by
pulling the lower part of the
evaporator while lifting it up.

Evaporator Cover

In

Freezer

Part Name How To Do Descriptive Picture

1. Remove the freezer door and
freezer drawer bin by pulling out
the drawer and then unscrewing
2 screws.

2. Lift up the evaporator cover.

3. Disengage the 3 housing
connector and remove the
evaporator cover.

43

DISASSEMBLY AND REASSEMBLY

3-28) Machine Compartment

Motor Fan

Part Name How To Do Descriptive Picture

1. Unscrew 8 screws of cover
compressor.

2. Disengage the housing
connector.
(Refer to the picture)

3. Remove the hooker of support
circuit motor by lifting the hooker
up and pulling it out.

4. Remove the spring with a flat­blade screwdriver.
(Refer to the picture)

5. Remove the motor fan by pulling
the fan out while grasping the
motor part.
(Refer to the picture)

6. Unscrew 2 screws fixed in the
motor.

7. Remove the hook of the motor
cover with a flat-blade (-)
screwdriver and then remove
the motor.

44

DISASSEMBLY AND REASSEMBLY

Relay

PTC & O/L

Water Valve

Part Name How To Do Descriptive Picture

1. Disengage the housing
connector.

2. Remove the relay PTC with a
flat-blade screwdriver.
(Refer to the picture)

1. Unscrew the water valve fixed
by the screw.

2. Remove the the hook part of the
hose by pushing it down.

3. Remove 2 water hose parts
while pushing the upper part of

.

(Refer to the picture)

4. Disengage 2 housing connector
parts.

5. Remove the hose connected by
the nut with a wrench(8mm).

45

DISASSEMBLY AND REASSEMBLY

Power Cord &

Noise Filter

Part Name How To Do Descriptive Picture

1. Unscrew 2 screws.

2. Disengage the housing
connector.

3. Unscrew 3 earth screws.

4. Remove the cover by pushing
the hook up using a flat-blade(-)
screwdriver.
(Refer to the picture)

5. Disengage the housing
connector to separate the power
cord and noise filter.

46

DISASSEMBLY AND REASSEMBLY

3-29) Electric Box

PBA Main

PBA SMPS

Part Name How To Do Descriptive Picture

1. Pull the refrigerator forward to
have enough space to work on
the rear side of the appliance.

2. Unscrew 2 screws for the PCB
cover.

3. Disengage all housing
connectors connected with main
PCB.

4. Unscrew 2 PCB fixed screws.

5. Remove the main PCB while
lifting the upper part of the hook
up.
(Refer to the picture)

1. Remove the cover PCB and
then disengage the housing
connector connected with main
PCB.
Remove the SMPS PCB while
pushing the lower part of the
hook down.

47

4. TROUBLESHOOTING

4-1) FUNCTION FOR FAILURE DIAGNOSIS 48

4-1-1. TEST MODE

48

4-1-2. DISPLAY FUNCTION OF COMMUNICATION ERROR

49

4-1-3. SELF-DIAGNOSTIC FUNCTION

50

4-1-4. DISPLAY FUNCTION OF LOAD CONDITION

53

4-1-5. EXHIBITION MODE SETTING FUNCTION

54

4-1-6. OPTION SETTING FUNCTION

54

4-1-7. OPTION TABLE

57

4-2) DIAGNOSTIC METHOD ACCORDING TO THE TROUBLE SYMPTOM

59

4-2-1. IF THE TROUBLE IS DETECTED BY SELF-DIAGNOSIS

60

4-2-2. IF FAN DOES NOT OPERATE

70

4-2-3. IF ICE ROOM FAN DOES NOT OPERATE

71

4-2-4. IF ICE MAKER DOES NOT OPERATE

72

4-2-5. IF DEFROST DOES NOT OPERATE

73

4-2-6. IF POWER IS NOT SUPPLIED

74

4-2-7. IF COMPRESSOR DOES NOT OPERATE

75

4-2-8. WHEN ALARM SOUND CONTINUOUS WITHOUT STOP

76

4-2-9. IF PANEL PCB DOES NOT WORK NORMALLY

78

4-2-10. IF PANTRY PANEL PCB IS NOT WORKING NORMALLY

79

4-2-11. WHEN REFRIGERATOR ROOM LAMP DOES NOT LIGHT UP

80

4-2-12. IF ICE WATER IS NOT SUPPLIED

81

4-2-13. IF WATER IS NOT SUPPLIED

82

4-2-14. IF CUBED OR CRUSHED ICE IS NOT SUPPLIED

83

4-2-15. IF COVER ICE ROUTE MOOR IS NOT WORKING NORMALLY

84

48

TROUBLESHOOTING

4-1) Function for failure diagnosis

● If Energy Saver Key + Fridge/Power Cool Key on the front of panel are pressed simultaneously

for 8 seconds , it will be changed to the test mode and all displays on the front of panel will be off.

● If any key on the front of panel is pressed within 15 seconds after the test mode, it will be

operated as below sequence :
manual operation(fresh food compartment)

manual defrost of fresh food compartment(rd)

manual defrost of fresh food and freezer compartments (Fd) Cancel(Display all off).

● If any key on the front of panel is not pressed within 15 seconds after the test mode, the test

mode will be canceled and it will be returned to previous mode.

1) Manual operation function

If Energy Saver Key + Fridge/Power Cool Key are pressed simultaneously for

8 seconds, (displays are all off)

It will be changed to the test mode (manual operation) by pressing any key

4-1-1. Test mode (manual operation / manual defrost function)

1-1) If any key is pressed once in test mode, blinks "FF" on the display and it indicates the

refrigerator has entered the manual operation. At this moment, buzzer beeps as an
alarm.

1-2) If manual operation is selected, compressor will run at once without 5 minutes delay in

any mode. If the refrigerator is on the defrost cycle at the moment, defrost will be
finished and manual operation will begin.
(Be careful if manual operation get started at the moment of compressor off, over load
could be occurred)

1-3) If manual operation works, compressor & f-fan operate continuously for 24 hours and

fresh food compartment will be controlled by the setting temperature.

1-4) When the manual operation runs, setting temperature will be selected automatically as

below: freezer compartment -14

(-25 ), fresh food compartment 33.8 (1 ).

1-5) During manual operation, Power Freeze & Power Cool function will not be worked.

If a function is selected, the power function icon of the selected function will be off
automatically after 10 seconds.

1-6) Manual operation can be canceled during manual operation by turning on the appliance

after power off(reset) or choosing the step 4) test cancel mode.

1-7) Alarm(0.25 sec ON/ 0.75 sec OFF) will beep continuously until manual operation is

completed and there is no function to make the sound stop.

2¢(-19¡) is recommended 38¢(3¡) is recommended

2¢(-19¡) is recommended

49

TROUBLESHOOTING

2) Manual defrost(fresh food compartment) function

4-1-2. Display function of Communication error

2-1) If any key is pressed one more time during manual operation(fresh food compartment),

"rd" shows in the display and then manual operation will be canceled at once and fresh
food compartment will be defrosted.

2-2) At this moment, alarm beeps for 3 seconds(0.1 sec ON/ 1 sec OFF) during manual

defrost(fresh food compartment) function.

2¢(-19¡) is recommended

3) Simultaneous manual defrost(fresh food and freezer compartments) function

3-1) If any key is pressed one more time during manual defrost(defrost of fresh food

compartment, "rd"), "Fd" shows on the display and then fresh food and freezer
compartments defrost will operate.
Manual defrost of Fresh food and freezer compartments are followed by manual defrost
freezer compartment.

3-2) At this moment, alarm beeps for 3 seconds (0.5 sec ON/ 0.5 sec OFF) during manual

defrost function of fresh food and freezer compartment.

4-1) During defrosting of fresh food and freezer compartments simultaneously, if the display

panel change to the test mode and test button is pressed one more time, defrosting of
fresh food and freezer compartments will be canceled at the same time and will return
to the normal operation.
Or, all test functions will be canceled by turning main power ON and OFF.

1-1) If there is no answer for 10 seconds after the panel micom received the requirement of

communication, "Pc - Er" display on the panel PCB will be ON/OFF alternately until the
communication error is canceled. (0.5 sec ALL ON, 0.5 sec ALL OFF alternately)

2¢(-19¡) is recommended

2¢(-19¡) is recommended

4) Test cancel mode

(0.5 sec ALL ON, 0.5 sec ALL OFF alternately)

1) Display function when Panel

MAIN MICOM communication has error

50

2-1) If there is no answer for 20 seconds after the main micon received the requirement of

communication from load MICOM, "Lc - Er" display on the panel PCB will be ON/OFF
alternately until the communication error is canceled.

2-2) Also pantry room display will be ON/OFF alternately until the communication error is

canceled.

2¢(-19¡) is recommended

(0.5 sec ALL ON, 0.5 sec ALL OFF alternately)

(0.5 sec ALL ON, 1.5 sec ALL OFF alternately)

2) Display function when MAIN

LOAD MICOM communication has error

TROUBLESHOOTING

4-1-3. Self-diagnostic function

1-1) Micom operates self-diagnostic function to check the temperature sensor condition

within 1 second when the refrigerator turned On initially.

1-2) If bad sensor is detected by the self-diagnostic function, the applicable display LED will

blink for 0.5 sec.
At this moment, there is no beep sound.(Refer to self-diagnostic CHECK LIST)

1-3) Self-diagnostic button is recognized only when the error is displayed by the bad sensor.

Display does not operate normally but temperature control will be controlled by the
emergency operation.

1-4) When the error is detected by self-diagnosis, the error can be canceled automatically if

all troubled sensors are corrected or Self-diagnostic function key (Energy Saver Key +
Alarm/Lighting Key ) are pressed simultaneously for 8 seconds.
(Return to normal display mode)

1) Self-diagnostic function in the Initial power ON

2) Self-diagnostic function during normal operation

If Energy Saver Key + Alarm/Lighting Key are pressed simultaneously

for 8 seconds, the error mode by self-diagnosis will be canceled.

2¢(-19¡) is recommended 38¢(3¡) is recommended

2¢(-19¡) is recommended 38¢(3¡) is recommended

51

TROUBLESHOOTING

2-1) If Energy Saver Key + Alarm/Lighting Key are pressed simultaneously for 6 seconds

during normal operation, the temperature setting display will operate for 2 seconds
(ON/OFF 0.5sec each).
If Energy Saver Key + Alarm/Lighting Key are pressed simultaneously for 8 seconds
(including above 2 seconds), self-diagnostic function will be selected.

2-2) At this moment, self-diagnostic function will be returned with buzzer sound 'ding-dong'.

If there is an error, display of error will be operated for 30 seconds and then return to
normal condition whether problem is corrected or not.
(Refer to self-diagnosis CHECK LIST)

2-3) Input by button is not accepted during self-diagnostic function.

󳢬 Self-diagnosis CHECK LIST

NO

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19

Trouble item
Ice Maker Sensor Error
R-Sensor Error
R-DEF-Sensor Error
R-FAN Error
Ice Maker Error
R-DEF, Heater Error
Ambient-Sensor Error
F-Sensor Error
F-DEF-Sensor Error
F-FAN Error
C-FAN Error
Ice Room-Sensor Error
F-DEF.-Heater Error
Ice Room FAN Error
Pantry-Damper-Heater Error
Pantry-Sensor Error
Panel Main Micom Error
L M communication Error
Water Tank-Heaer Error

Display LED

R-1­R-1­R-1­R-1­R-1­R-1­F-1­F-1­F-1­F-1­F-1­F-1-

F-1­F-10­R-10­R-10­F-10­F-10­R-10-

Trouble contents
ICE MAKER SENSOR part error
R SENSOR part error
R defrost SENSOR part error
R inner part error
ICE MAKER operation error
R defrost part error
external SENSOR part error
F SENSOR part error
F defrost SENSOR part error
F inner fan motor part error
machine room fan motor part error
ICE ROOM SENSOR part error
F defrost part error
ICE ROOM inner fan motor part error
Damper Heater open/wire error
Pantry Room SENSOR part error
Panel Mai Micom communication error
LOAD Main Micom communication error
Water Tank Heater open/wire error

F-1

F-10

R-1

R-10

2¢(-19¡) is recommended 38¢(3¡) is recommended

52

󳢬 Self-diagnostics check list

TROUBLESHOOTING

LED

R-1-

R-1-

R-1-

R-1-

R-1-

R-1-

F-1-

F-1-

F-1-

F-1-

F-1-

F-1-

F-1-

F-10-

R-10-

R-10-

R-10-

F-10-

F-10-

Item

Ice Maker Sensor Error

R-Sensor Error

R-DEF-Sensor Error

R-FAN Error

Ice Maker Error

R-DEF. Error

Ambient-Sensor Error

F-Sensor Error

DEF-Sensor Error

F-FAN Error

C-FAN Error

Ice Room Sensor Error

F-DEF. Error

Ice Room-FAN Error

Pantry-Damper-Heater Error

Pantry-Sensor Error

Water Tank-Heater Error

Panel Main communication Error

Load Main communication Error

Trouble contents

Diagnostic method

Display error : separation of sensor housing
part, contact error, disconnection, short
circuit
Display error of detecting temperature of
sensor: more than 149 (+65°C) or less
than -58 (-50°C)

Display error : sensor housing separation,
contact error, disconnection, short circuit
Display error by detecting temperature of
sensor: more than 149 (+65°C) or less
than -58 (-50°C)

Display "OP/LC-Er" in the panel with alarm :
MICOM MAIN LOAD communication error
MICOM MAIN PANEL communication error
LC-Er is displayed when the Option is not
equivalent with the right value

Actually, it is desirable to recheck the condition with
the oscilloscope after replacing Main and Panel
PCB.

When checking the voltage of MAIN PCB CN90
#3 CN90#4 : shall be between 4.5V~1.0V.

When checking the voltage of MAIN PCB
CN30#6 CN75#1:shall be between 4.5V~1.0V

When checking the voltage of MAIN PCB
CN30#7 CN75#:shall be between 4.5V~1.0V

Voltage of MAIN PCB CN75 Orange Gray
shall be between 7V~12V

After replacing ice maker, check the operation
by turning the appliance ON again.

When checking the voltage of MAIN PCB
CN32#1 #4 : shall be between 4.5V~1.0V.

When checking the voltage of MAIN PCB
CN30#3 CN75#1:shall be between 4.5V~1.0V

When check the voltage of MAIN PCB
CN30#4 CN75#1:shall be between 4.5V~1.0V

Voltage of MAIN PCB CN75 Yellow Gray
shall be between 7V~12V.

Voltage of MAIN PCB CN75 Sky-blue Gray
shall be between 7V~12V.

When check the voltage of MAIN PCB
CN32#3 CN75#1:shall be between 4.5V~1.0V

When checking the voltage of MAIN PCB
CN30#8 #9 : shall be between 4.5V~1.0V.

After separating MAIN PCB CN78from PCB, check the resistant
value between Black

brown wire shall be 48 ohm 7%.

Check 0 Ohm : heater short,

Ohm : wire / bimetal Open.

Display error : separation of fresh food compartment defrost heater housing
part, contact error, disconnection, short circuit or temperature fuse error.
Display error : the defrosting does not finish though fresh food compartment
defrost is heating continuously for more than 80 minutes.

After separating MAIN PCB CN70,CN71 from PCB, check the resistance value
between CN70 White

CN71 Orange shall be 102(441) ohm 7%.
(Resistant value is varied by the input power)
Check 0 Ohm : heater short,

Ohm : wire / bimetal Open.

After separating MAIN PCB CN70,CN71 from PCB, check the
resistant value between CN70 brown

CN71 Orange shall be

102(220) ohm

7%. (Resistant value is varied by input power)

Check 0 Ohm : heater short,

Ohm : wire / bimetal Open.

After separating MAIN PCB CN91from PCB, check the resistant
value between Black brown wire shall be 145 ohm 7%.
Check 0 Ohm : heater short, Ohm : wire / bimetal Open.

Voltage of MAIN PCB CN76 Black

CN75 Gray : shall be

between 6V~12V.

Display error : separation of freezer compartment defrost heater housing
part , contact error, disconnection, short circuit or temperature fuse error.
Display error : the defrosting does not finish though fresh food compartment
compartment defrost is heating continuously for more than 70 minutes.

Display error during operation of applicable
fan motor : Feed Back signal line contact
error, separation of motor wire, motor error

Display error : ice making kit is harvested
more than 3 times and level error
** Apply to the applicable Ice Maker model.

Display error during operation of applicable
fan motor : Feed Back signal line contact
error, motor wire separation, motor error

Display error during operation of applicable
fan motor : Feed Back signal line contact
error, motor wire separation, motor error

Display error : sensor housing separation,contact error,
disconnection, short circuit.
Display error by detecting temperature of sensor: more
than 149 (+65°C) or less than -58 (-50°C)

Display error when open error is detected by damper
heater : separation of Damper Heater housing part,
contact error, disconnection, short circuit

Display error during operation of applicable fan motor :
Feed Back signal line contact error, motor wire separation,
motor error

Display error : separation of sensor housing, contact error,
disconnection, short circuit.
Display error by detecting temperature of sensor: more than 149
(+65°C) or less than -58 (-50°C)

Display error when open error is detected by Water Tank
Heater : separation of Water Tank Heater housing
part,contact error, disconnection, short circuit

53

TROUBLESHOOTING

4-1-4. Display function of Load condition

1) If Power Energy Saver Key + Alarm/Lighting key are pressed simultaneously for 6 seconds during normal
operation, the temperature setting display of fresh food and freezer compartments will blink ALL ON/OFF with

0.5 for 2 seconds.

2) At this moment, If Fridge/Power Cool Key after Energy Saver Key + Alarm/Lighting Key is pressed, load
condition display mode will be returned with alarm.

3) Load condition display mode shows the load that micom signal is outputting.
However, It means that micom signal is outputting, it does not mean whether load is operating or not. That is to
say that though load operation is displayed, load could not be operated by actual load error or PCB relay error
etc. (This function would be applied at A/S.)

4) Load condition display function will maintain for 30 seconds and then normal condition will be returned
automatically.

5) Load condition display is as below.

If Energy Saver Key + Alarm/Lighting key are pressed simultaneously for 6
seconds, ALL ON/OFF will blink with 0.5interval for 2 seconds.
If take the finger off from above keys and press Fridge/Power Cool Key, load
condition mode will be started.

F-1

F-10

R-1

R-10

󳢬 Load mode Check list

Display LED

R-1­R-1­R-1­R-1­R-1­R-1-

F-1- , ALL LED Off

R1­F-1­F-1­F-1­F-1-

R-10­R-10­F-10-

F-1-

F-10­F-10­F-10-

Operation contents
When fresh food compartment fan high operates, applicable LED ON
When fresh food compartment fan low operates, applicable LED ON
When fresh food compartment defrost heater operates, LED ON
Initial power ON refrigerator, LED ON
When ambient temperature is more than 93

(34°C), LED ON

When ambient temperature is less than 72

(22°C), LED ON

When ambient temperature is between 73

(23°C) ~ 91 (33°C), LED ON
Display mode, LED ON
When compressor operates, applicable LED ON
When freezer compartment fan high operates, applicable LED ON
When freezer compartment fan low operates, applicable LED ON
When freezer compartment defrost heater operates, LED ON
When compressor fan high operates, applicable LED ON
When compressor fan low operates, applicable LED ON
When french heater operates, applicable LED ON
When dispenser heater operates LED ON
When water tank heater operates LED ON
When Ice room fan high operates LED ON
When Ice room fan low operates LED ON

Display contents
R-FAN High
R-FAN Low
R-DEF Heater
Start Mode
Overload condition
Low temperature condition
Normal Condition
Exhibition Mode
COMP.
F-FAN High
F-FAN Low
F-DEF Heater
C-FAN High
C-FAN Low
French Heater
Dispenser Heater
Water Tank Heater
Ice Room-FAN High Ice
Ice Room-FAN Low

2¢(-19¡) is recommended 38¢(3¡) is recommended

2¢(-19¡) is recommended 38¢(3¡) is recommended

54

TROUBLESHOOTING

4-1-5. Exhibition mode setting function

1) If Energy Saver Key + Freezer/Power Freeze are pressed simultaneously for 3 seconds during
normal operation, show room mode will be started with buzzer sound(ding-dong).

2) If above Energy Saver Key + Freeze/Power Freeze are pressed one more time, show room
mode will be canceled.

3) If show room mode is selected, blinks "OF-OF" on the temperature setting display of the panel
and it indicates the refrigerator has entered the show room mode.

4) During show room mode, if fresh food and freezer compartments sensors are higher than
149

(65 ) show room mode will be canceled automatically and freezing operation will be
returned.
(There is no buzzer sound when the show room mode is canceled by the temperature)

5) Operation contents of show room mode

- Display, Fan motor and etc operate normally, not to operate compressor only.

- Defrost is not operated. (including french heater)

- Display function of the initial real temperature is finished.

- Under the condition of show room mode, show room mode will be operated when Power On

after Power OFF.

If Energy Saver Key + Power Freeze Key are pressed for 3 seconds, show room
mode will be started.

4-1-6. Option setting function

If Freezer/Power Freeze Key+ Alarm/lighting Key are pressed simultaneously for 12 seconds
during normal operation, fresh food and freezer compartments temperature display will be
changed to option setting mode.

If Freezer/Power Freeze Key+ Alarm/lighting Key are pressed simultaneously for 12
seconds, option setting mode will be started.

KEY operation method for changing to option mode

2¢(-19¡) is recommended 38¢(3¡) is recommended

2¢(-19¡) is recommended 38¢(3¡) is recommended

55

TROUBLESHOOTING

1) For example, if you want to change freezer compartment standard temperature to 28.4 (­2°C) by operating option, do as below.
This function is for changing the standard temperature.
In -2 (-19°C) of current temperature of freezer compartment, if you make the temperature
lower to 28.4 (-2°C) by the option, the standard temperature would be controlled -6 (-21°C)
Therefore, if you change the setting of temperature option to -2 (-19°C) on the panel, the
appliance will be operated with -6 (-21°C).
It means that standard temperature is controlled 28.4 (-2°C) less than setting temperature in
the display.

If the display changes to option setting mode, all displays will be off except freezer and
fridge compartments temperature display as below.
(Fresh food and freezer compartments case will be explained only because all options
are operated with the same method according to the option table.)

Code Up

Code

Reference

Value

Reference

Value Up

Code Down

Reference Value Down

2¢(-19¡) is recommended 38¢(3¡) is recommended

KEY control method after converting to option mode

󳢬 Key control in option mode

Energy Saver

Freezer/Power Freeze

Alarm/Lighting

Fridge/Power Cool

Code Down key

Code Up key

Reference Value down key

Reference Value Up key

Basically, option function has cleared data at shipping process.
Therefore, almost all setting value are "0".
Check the product information manual or specifications because setting value could be
changed particularly for the purpose of improving product at mass producing process.

NOTE

2¢(-19¡) is recommended 38¢(3¡) is recommended

Reference ValueCode

56

TROUBLESHOOTING

2) After changing to the option mode, fresh food compartment "0" , freezer compartment
"0" will be displayed. ( Basically fresh food compartment "0", freezer "0" would be set at
shipping process, but setting value could be changed for the purpose of improving
product at mass producing process.)

- If fresh food compartment "0" shows only, temperature reference value of freezer

compartment will be set and current freezer compartment temperature code will be
displayed on the freezer temperature display.

3) If freezer compartment "4" is set as below freezer compartment code after fresh food
compartment "0 is set, standard temperature of freezer compartment will be lower than

28.4

(-2.0°C).

(Refer to the picture "changing the freezer compartment temperature")

: If you wait for 20 seconds after completing the setting, MICOM will save the setting value

to the EEPROM and normal display will be returned and the option setting mode will be
canceled.

4) Option changing method as above is the same as all RF266/265** model.

5) By the same method as above, it is possible to control the fresh food compartment
temperature, water supply, ice-maker harvest temperature/time, defrost return time,
hysteresis by temperature, notch gap by temperature etc.

6) Option function is set in the EEPROM at shipping process in the factory.
You would better not to change the option of your own.
Completing the setting is that option function return to normal display after 20 seconds.
Do not turn off the appliance before returning to the normal display mode.

Reference ValueCode

2¢(-19¡) is recommended 38¢(3¡) is recommended

Option setting function exists in the other items.
We will skip the explanation of the other functions by the option because it is
associated with refrigerator control function and is not needed at SERVICE.
(Please do not set the other options except above SERVICE Manual.)

NOTE

57

Reference ValueCode

2¢(-19¡) is recommended 38¢(3¡) is recommended

TROUBLESHOOTING

4-1-7. Option TABLE

1) Temperature changing table of freezer compartment

ex) If you want to change the freezer standard temperature to 28.4 (-2°C)

Set item Freezer Temp Shift
MODEL RF267AA / RF26DB

Fridge Room 7-SEG

0

Setting value

Temp.

compensation

0
1
2
3
4
5
6
7
8

9
10
11
12
13
14
15

32 (0.0°C)

31.1 (-0.5°C)

30.2 (-1.0°C)

29.3 (-1.5°C)

28.4 (-2.0°C)

27.5 (-2.5°C)

26.6 (-3.0°C)

25.7 (-3.5°C)

32.9 (+0.5°C)

33.8 (+1.0°C)

34.7 (+1.5°C)

35.6 (+2.0°C)

36.5 (+2.5°C)

37.4 (+3.0°C)

38.3 (+3.5°C)

39.2 (+4.0°C)

FZ

compartment

Code

Reference

Value

Reference ValueCode

2¢(-19¡) is recommended 38¢(3¡) is recommended

2) Temperature changing table of fresh food compartment

ex) If you want to change the Fresh Food

compartment standard temperature to 35.6 (2°C)

Set item Freezer Temp Shift
MODEL RF267AA / RF26DB

Fridge Room 7-SEG

1

Setting value

Temp.

compensation

0

1

2

3

4

5

6

7

8

9
10
11
12
13
14
15

32 (0.0°C)

31.1 (-0.5°C)

30.2 (-1.0°C)

29.3 (-1.5°C)

28.4 (-2.0°C)

27.5

(-2.5°C)

26.6

(-3.0°C)

25.7 (-3.5°C)

32.9 (+0.5°C)

33.8 (+1.0°C)

34.7

(+1.5°C)

35.6

(+2.0°C)

36.5 (+2.5°C)

37.4 (+3.0°C)

38.3 (+3.5°C)

39.2

(+4.0°C)

FZ

compartment

Code

Reference

Value

58

TROUBLESHOOTING

59

TROUBLESHOOTING

4-2) Diagnostic method according to the trouble symptom(Flow Chart)

DATA1.Temperature table
Resistance value and MICOM port voltage of sensor according to the temperature
SENSOR CHIP : based on PX41C

-50

-49

-48

-47

-46

-45

-44

-43

-42

-41

-40

-39

-38

-37

-36

-35

-34

-33

-32

-31

-30

-29

-28

-27

-26

-25

-24

-23

-22

-21

-20

-19

-18

-17

-16

-15

-14

-13

-12

-11

-10

-9

-8

-7

-6

-58

-56.2

-54.4

-52.6

-50.8

-49

-47.2

-45.4

-43.6

-41.8

-40

-38.2

-36.4

-34.6

-32.8

-31

-29.2

-27.4

-25.6

-23.8

-22

-20.2

-18.4

-16.6

-14.8

-13

-11.2

-9.4

-7.6

-5.8

-4

-2.2

-0.4

1.4

3.2
5

6.8

8.6

10.4

12.2
14

15.8

17.6

19.4

21.2

4.694

4.677

4.659

4.641

4.622

4.602

4.581

4.560

4.537

4.514

4.490

4.465

4.439

4.412

4.385

4.356

4.326

4.296

4.264

4.232

4.199

4.165

4.129

4.093

4.056

4.018

3.980

3.940

3.899

3.858

3.816

3.773

3.729

3.685

3.640

3.594

3.548

3.501

3.453

3.405

3.356

3.307

3.258

3.208

3.158

153319
144794
136798
129294
122248
115631
109413
103569

98073
92903
88037
83456
79142
75077
71246
67634
64227
61012
57977
55112
52406
49848
47431
45146
42984
40938
39002
37169
35433
33788
32230
30752
29350
28021
26760
25562
24425
23345
22320
21345
20418
19537
18698
17901
17142

℃℉

Voltage

Resistance

-5

-4

-3

-2

-1
0
1
2
3
4
5
6
7
8
9

10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39

23

24.8

26.6

28.4

30.2
32

33.8

35.6

37.4

39.2
41

42.8

44.6

46.4

48.2
50

51.8

53.6

55.4

57.2
59

60.8

62.6

64.4

66.2
68

69.8

71.6

73.4

75.2
77

78.8

80.6

82.4

84.2
86

87.8

89.6

91.4

93.2
95

96.8

98.6

100.4

102.2

3.107

3.057

3.006

2.955

2.904

2.853

2.802

2.751

2.700

2.649

2.599

2.548

2.498

2.449

2.399

2.350

2.301

2.253

2.205

2.158

2.111

2.064

2.019

1.974

1.929

1.885

1.842

1.799

1.757

1.716

1.675

1.636

1.596

1.558

1.520

1.483

1.447

1.412

1.377

1.343

1.309

1.277

1.253

1.213

1.183

16419
15731
15076
14452
13857
13290
12749
12233
11741
11271
10823
10395

9986
9596
9223
8867
8526
8200
7888
7590
7305
7032
6771
6521
6281
6052
5832
5621
5419
5225
5039
4861
4690
4526
4369
4218
4072
3933
3799
3670
3547
3428
3344
3204
3098

℃℉

Voltage

Resistance

40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84

104

105.8

107.6

109.4

111.2
113

114.8

116.6

118.4

120.2
122

123.8

125.6

127.4

129.2
131

132.8

134.6

136.4

138.2
140

141.8

143.6

145.4

147.2
149

150.8

152.6

154.4

156.2
158

159.8

161.6

163.4

165.2
167

168.8

170.6

172.4

174.2
176

177.8

179.6

181.4

183.2

1.153

1.124

1.095

1.068

1.040

1.014

0.988

0.963

0.938

0.914

0.891

0.868

0.846

0.824

0.803

0.783

0.762

0.743

0.724

0.706

0.688

0.670

0.653

0.636

0.620

0.604

0.589

0.574

0.560

0.546

0.532

0.519

0.506

0.493

0.481

0.469

0.457

0.446

0.435

0.424

0.414

0.404

0.394

0.384

0.375

2997
2899
2805
2714
2627
2543
2462
2384
2309
2237
2167
2100
2036
1973
1913
1855
1799
1745
1693
1642
1594
1547
1502
1458
1416
1375
1335
1297
1260
1225
1190
1157
1125
1093
1063
1034
1006

978
952
926
902
877
854
832
810

℃℉

Voltage

Resistance

60

TROUBLESHOOTING

- The error of sensor will be displayed on the front of display.
when the error of sensor is detected at initial power ON, the appliance will not operated and display
of abnormal sensor part will blink.

- The appliance will not stop operating when the error of sensor is detected during operation of the
appliance.
But normal freezing might be not operated if the appliance is operated by the emergency operation
mode. You would better to check the appliance according to the self-diagnosis of the manual.

4-2-1. If the trouble is detected by self-diagnosis

1) If ICE Maker Sensor has trouble

Bad contact of connector/ insert correctly

Is MAIN PCB Connector

CN90 inserted correctly?

Is ICE Maker Sensor

unit normal?

Is the voltage between

MAIN PCB Connector CN90#"4"(White) and

CN1#"3"(Black) normal?

Is input voltage of IC02

MICOM #30 normal?

Start

NO

YES

YES

YES

YES

Replace the temperature sensor

NO

Recheck the wire connection part

NO(0.6V > Measurement < 4.6V)

Check the iced-solder, solder

bridging, disturbed solder.

NO

No trouble with PCB and temperature sensor.

Recheck the bad contact of the connection.

** Measuring point of resistance value according to

Sensor **
ICE MAKER : CN90#8 #4 measuring resistance value
** 0 : Short trouble / : Open trouble

Sensor MICOM/Connector number

Voltage measured between 4.6V ~ 0.6V.

Measuring voltage of IC02 MICOM #30,

CN90#4(White) and CN1#3(Black) from

PCB typical Ground part are similar.

Checking method of ICE Maker Sensor resistance CN90#

"8(Sky-blue) #4"(White)

- Compare the temperature table after the measure.

DATA1.

Temperature table

ERROR Code

Refer to circuit diagram in the manual

ICE
Maker

Connector CN90#"4"(White) and
CN1#"3"(Black) PCB common Ground

Checking method of ICE Maker Sensor resistance

- Measure the voltage of Sensor Check Point #6(IC02 MICOM #30)
on PCB or CN90#4(White)

CN1#3(Black)

- Compare the temperature table after the measure.
Measuring voltage of CN90#4(White) CN1#3(Black) are below.

typical PCB Ground
CN1#3(Black)

2¢(-19¡) is recommended 38¢(3¡) is recommended

61

TROUBLESHOOTING

2) If R Sensor has trouble

Bad contact of connector/ insert correctly

Is MAIN PCB

Connector CN30 to CN75 inserted

correctly?

Is R Sensor

unit normal?

Is the voltage between

MAIN PCB Connector CN30#6(White) to

CN1#3(Black) normal?

Is the input voltage to

IC01 MICOM #54 normal?

Start

NO

YES

YES

YES

YES

Replace the temperature sensor

NO

Recheck the wire connection part

NO(0.6V > Measurement < 4.6V)

Check the iced-solder, solder bridging,

disturbed solder.

NO

No trouble with PCB and temperature sensor.

Recheck the bad contact of the connection.

** Measuring point of resistance value according to

Sensor **
R : CN30#6 CN75#1 measuring resistance value
** 0 : Short trouble / : Open trouble

Sensor MICOM/Connector number

Voltage measured between 4.6V ~ 0.6V.

Measuring voltage IC01 MICOM #54,

CN30#6(White) and CN1#3(Black)

from PCB typical Ground part are similar.

Checking method of R Sensor resistance
CN30#6(White) CN75#1(Gray) Compare the
temperature table after the measure.

DATA1.

Temperature table

ERROR Code

Refer to circuit diagram in the manual

R

Connector CN30#6(White) to
CN1#3(Black) PCB typical Ground

Checking method of R Sensor resistance

- Measure the voltage of Sensor Check Point #3(IC01 MICOM #54)
on PCB or CN30#6(White) CN1#3(Black)

- Compare the temperature table after the measure.
Measuring voltage of CN30#6(White)°ÍCN1#3(Black) are below.

typical PCB Ground
CN#3(Black)

2¢(-19¡) is recommended 38¢(3¡) is recommended

62

TROUBLESHOOTING

3) If R DEF Sensor has trouble

Bad contact of connector/ insert correctly

Is MAIN PCB

Connector CN30 to CN75 inserted

correctly?

Is R DEF Sensor

unit normal?

Is the input voltage between

MAIN PCB Connector CN30#7(Skyblue)

to CN1#3(Black) normal?

Is the input voltage of IC01

MICOM # 57 normal?

Start

NO

YES

YES

YES

YES

Replace the temperature sensor

NO

Recheck the wire connection part

NO(0.6V > Measurement < 4.6V)

Check the iced-solder, solder bridging,

disturbed solder.

NO

No trouble with PCB and temperature sensor.

Recheck the bad contact of the connection.

** Measuring point of resistance value according to

Sensor **
R-DEF : CN30#7 CN75#1 measuring
resistance value
** 0 : Short trouble / : Open trouble

Sensor MICOM/Connector Number

Voltage measured between 4.6V ~ 0.6V.

Measuring voltage of IC01 MICOM #57,

CN30#7(Sky-blue) and CN1#3(Black) from

PCB typical Ground part are similar.

Checking method of R Sensor resistance
CN30#7(Sky-blue) CN75#1(Gray)

- Compare the temperature table after the
measure.

DATA1.

Temperature table

ERROR Code

Refer to circuit diagram in the manual

R DEF

Connector CN30-"7"(Sky-blue) and
CN1-"3"(Black) PCB common Ground

Checking method of R DEF Sensor resistance

- Measure the voltage of Sensor Check Point #4(IC01 MICOM #57) on
PCB or CN30#7Sky-blue) CN1#3(Black)

- Compare the temperature table after the measure.

Measuring voltage of CN30#7(Sky-blue) CN1#3(Black) are below.

typical PCB Ground
CN1#3(Black)

Start

YES

YES

YES

2¢(-19¡) is recommended 38¢(3¡) is recommended

63

TROUBLESHOOTING

4) If Ambient Sensor has trouble

Bad contact of connector/ insert correctly

Is MAIN PCB

Connector CN32 inserted

correctly?

Is Ambient Sensor

unit normal?

Is the voltage between

MAIN PCB Connector CN32#1(White)

to CN1#3(Black) normal?

Is the input voltage of

IC01 MICOM #59 normal?

Start

NO

YES

YES

YES

YES

Replace the temperature sensor

NO

Recheck the wiring connection

NO(0.6V > Measurement < 4.6V)

Check the iced-solder, solder

bridging, disturbed solder

NO

No trouble with PCB and temperature sensor

Recheck the bad contact of the connection

** Measuring point of resistance value according to

Sensor **
Ambient : CN32#1 #4 measuring resistance value
** Placed in the right top table of upper hinge.
** 0 : Short trouble / : Open trouble

Sensor MICOM/Connector number

Voltage measured between 4.6V ~ 0.6V.

Measuring voltage of IC01 MICOM #59,
CN32#1(White) and CN1#3(Black) from

PCB typical Ground part are similar.

Checking method of Ambient Sensor resistance
CN32#1(White) #4(White)

- Compare the temperature table after the
measure

DATA1.

Temperature table

ERROR Code

Refer to circuit diagram in the manual

Ambient

Connector CN32#1(White) to
CN1#3(Black) PCB typical Ground

Checking method of Ambient Sensor voltage

- Measure the voltage of Sensor Check Point #7(IC01 MICOM #59)
on PCB or CN32#1(White) CN1#3(Black)

- Compare the temperature table after the measure

Measuring voltage of CN32#1(White) CN1#3(Black) are below

typical PCB Ground
CN1#3(Black)

Start

YES

YES

YES

2¢(-19¡) is recommended 38¢(3¡) is recommended

64

TROUBLESHOOTING

5) If F Sensor has trouble

Bad contact of connector/ insert correctly

Are MAIN PCB

Connector CN30 to CN75

inserted correctly?

Is F Sensor

unit normal?

Is the voltage between

MAIN PCB Connector CN30#3(Red) to

CN1#3(Black) normal?

Is the input voltage of

IC01 MICOM #52 normal?

Start

NO

YES

YES

YES

YES

Replace temperature sensor

NO

Recheck the wiring connection

NO(0.6V > Measurement < 4.6V)

Check the iced-solder, solder

bridging, disturbed solder

NO

No trouble with PCB and temperature sensor

Recheck the bad contact of the connection

** Measuring point of resistance value according to

Sensor **
F : CN30#3 CN75#1 measuring resistance value
** 0 : Short trouble / : Open trouble

Sensor MICOM/Connector number

Voltage measured between 4.6V ~ 0.6V.

Measuring voltage of IC01 MICOM #52,

CN30#3(Red) and CN1#3(Black) from

PCB typical Ground part are similar.

Checking method of F Sensor resistance

CN30#3(Red) CN75#1(Gray)

- Compare the temperature table after the measure

DATA1.

Temperature table

ERROR Code

Refer to circuit diagram in the manual

F

Connector CN30#3(Red) to
CN1#3(Black) PCB typical Ground

Checking method of F Sensor voltage

- Measure the voltage of Sensor Check Point #1(IC01 MICOM #52)
on PCB or CN30#3(Red) CN1#3(Black)

- Compare the temperature table after the measure

Measuring voltage of CN30#3(Red) CN1#3(Black) are below.

typical PCB Ground
CN1#3(Black)

Start

YES

YES

YES

2¢(-19¡) is recommended 38¢(3¡) is recommended

65

TROUBLESHOOTING

6) If F DEF Sensor has trouble

Bad contact of connector/ insert correctly

Are MAIN PCB

Connector CN30 to

CN75 insert correctly?

Is F DEF Sensor

unit normal?

Is the voltage between

MAIN PCB Connector CN30#4(Orange)

to CN1#3(Black) normal?

Is the input voltage of

IC01 MICOM #53 normal?

Start

NO

YES

YES

YES

YES

Replace temperature sensor

NO

Recheck the wiring connection

NO(0.6V > Measurement < 4.6V)

Check the iced-solder, solder

bridging, disturbed solder

NO

No trouble with PCB and temperature sensor.

Recheck the bad contact of the connection.

** Measuring point of resistance value according to

Sensor **

F-DEF : CN30#4 CN75#1 measuring resistance

value

** 0 : Short trouble / : Open trouble

Sensor MICOM/Connector number

Voltage measured between 4.6V ~ 0.6V.

Measuring voltage of IC01 MICOM #53,

CN30#4(Orange) and CN1#3(Black) from

PCB typical Ground part are similar.

Checking method of F DEF Sensor resistance

CN30#4(Orange) CN75#1(Gray)

- Compare the temperature table after the measure.

DATA1.

Temperature table

ERROR Code

Refer to circuit diagram in the manual

F DEF

Connector CN30#4(Orange) to
CN1#3(Black) PCB typical Ground

Checking method of F DEF Sensor voltage

- Measure the voltage of Sensor Check Point #1(IC01 MICOM
#52) on PCB or CN30#4(Orange) CN1#3(Black)

- Compare the temperature table after the measure

Measuring voltage of CN30#4(Orange) CN1#3(Black) are below

typical PCB Ground
CN1#3(Black)

Start

YES

YES

YES

2¢(-19¡) is recommended 38¢(3¡) is recommended

66

TROUBLESHOOTING

7) If Ice Room Sensor has trouble

Bad contact of connector/ insert correctly

Is MAIN PCB

Connector CN32 inserted correctly?

Is Ice Room Sensor

unit normal?

Is the voltage between

MAIN PCB Connector CN32-”3”(Orange)

to CN1-”3”(Black) normal?

Is the input voltage of

IC01 MICOM #51 normal?

Start

NO

YES

YES

YES

YES

Replace temperature sensor

NO

Check the wiring connection

NO(0.6V > Measurement < 4.6V)

Check the iced-solder, solder

bridging, disturbed solder

NO

No trouble with PCB and temperature sensor.

Check the bad connections.

** Measuring point of resistance value according to

Sensor **

Ambient : CN32#3 CN75#1 Measure the resistance

value

** 0 : Short trouble / : Open trouble

Sensor MICOM/Connector number

Voltage measured between 4.6V ~ 0.6V.

Measuring voltage of IC01 MICOM #51,

CN32-”3”(Orange) and CN1-”3”(Black) from

typical PCB Ground are similar.

Checking Mehod of Ice Room Sensor voltage
CN32-”3”(Orange) CN75-”1” (Gray)

- Compare with the temperature table after
measurement.

DATA1.

Temperature table

ERROR Code

Refer to the circuit diagram in this manual

Ice Room

Connector CN32-”3”(Orange) and CN1-

”3”(Black) from typical PCB Ground

Checking Method of Ice Room Sensor Voltage

- Measure the voltage of sensor checking point #8(IC01 MICOM #51) on
PCB or CN32-”3” (Orange) CN1-”3”(Black)

- Compare with the temperature table after measurement.
Measured voltage of CN32-”3” (Orange) CN1-”3” (Black) are below

Typical PCB Ground CN1-”3”
(Black)

Start

YES

YES

YES

2¢(-19¡) is recommended 38¢(3¡) is recommended

67

TROUBLESHOOTING

8) If Pantry Sensor has trouble

Bad contact of connector/ insert correctly

Is MAIN PCB

Connector CN30 insert

correctly?

Is Pantry Sensor

normal?

Is the voltage between

MAIN PCB Connector CN30#8(Whiteblack)

to CN1#3(Black) normal?

Is the input voltage of IC01

MICOM Pin# 58 normal?

Start

NO

YES

YES

YES

YES

Replace temperature sensor

NO

Recheck the wiring connection

NO(0.6V > Measurement < 4.6V)

Check the iced-solder, solder

bridging, disturbed solder

NO

No trouble with PCB and temperature sensor.

Recheck the bad contact of the connection.

** Measuring point of resistance value according to

Sensor **
Pantry : CN30#8 #9 measuring resistance value
** 0 : Short trouble / : Open trouble

Sensor MICOM/Connector number

Voltage measured between 4.6V ~ 0.6V.

Measuring voltage of IC01 MICOM #58,

CN30#8(White-black) and CN1#3(Black)

from PCB typical Ground part are similar.

Checking method of Pantry Sensor resistance

CN30#8(White-black) #9(Gray)

- Compare the temperature table after the measure

DATA1.

Temperature table

ERROR Code

Refer to circuit diagram in the manual

Pantry

Connector CN30#8(White-black) to
CN1#3(Black) PCB typical Ground

Checking method of Pantry Sensor voltage

- Measuring voltage of Sensor Check Point #5(IC01 MICOM #58) on
PCB or CN30#8(White-black) CN1#3(Black)

- Compare the temperature table after the measure

Measuring voltage of CN30#8(white-black) CN1#3(Black) are below

typical PCB Ground
CN1#3(Black)

Start

YES

YES

YES

2¢(-19¡) is recommended 38¢(3¡) is recommended

68

TROUBLESHOOTING

9) If Pantry Room Damper Heater has trouble

Replace Damper

Is Damper Heater

normal?(about145ohm)

Is MAIN PCB connector

(CN91) inserted correctly?

Is the input voltage of

IC02 MICOM #37 normal?

Start

NO

YES

YES

YES

Bad contact of connector/ insert correctly

NO

1) Recheck the wire

2) Replace PCB MAIN

NO

Normal(recheck)

Measure the resistance

between - after

CN90 connector open 145ohm 7%

ERROR Code

Checking method of Pantry Room Damper

resistance CN91#1(Black) #2(Brown)

** : Open(wire disconnection, heater

disconnection) trouble 0 : Short trouble

Start

YES

YES

YES

Initial

power On

Damper

heater off

Damper

heater On

4.0V ~

4.5V

MICOM

#37

condition

4.0V ~

4.5V

0V

2¢(-19¡) is recommended 38¢(3¡) is recommended

69

TROUBLESHOOTING

10) If Tank Water Heater has trouble

Replace Tank Water Heater

Is Tank Water Heater

normal?(about48ohm)

Is MAIN PCB connector

(CN78) inserted correctly?

Is the input voltage of

IC01 MICOM #8 normal?

Start

NO

YES

YES

YES

Bad contact of connector/ insert correctly

NO

1) Recheck the wire

2) Replace PCB MAIN

NO

Normal(recheck)

Measure the resistance

between - after

CN78 connector open 48ohm 7%

ERROR Code

Checking method of Tank Water Heater

resistance CN78#5(Black) #4(Brown)

** : Open(wire disconnection, heater

disconnection) trouble 0 : Short trouble

Start

YES

YES

YES

2¢(-19¡) is recommended 38¢(3¡) is recommended

70

TROUBLESHOOTING

- The refrigerator of this model has BLDC FAN motor. BLDC motor is driven by DC 7~12V.

- On the normal condition of COMP ON, it operates together with F-FAN motor.
If door is opened and closed once at a high ambient temperature, it will be operated after 1 minute
delay.
Therefore, you are advised not to taken it for an error.

-. If there is a trouble, you should select the self-diagnostic function to check the trouble before power off.

4-2-2. If FAN does not operate

Start

Is COMPRESSOR ON ?

Door & MICOM State

Door

F FAN pulse voltage

CN75#5(Black)

The voltage measured around 2~3V
with multi-meter though the voltage is
very weak because of pulse signal

Display for checking the self-diagnostic function

R FAN ERROR

typical PCB Ground

CN10#3(Black)

F

MICOM

(#50)

Close

Open

5V(High)

0V(Low)

0V(Low)

5V(High)

R MICOM(#3)

Right and Left

Execute manual

operation

FAN work normally

Repair the connection

of Door switch

Replace MAIN PCB

1) R-FAN 2) F-FAN 3) C-FAN

typical PCB Ground
CN1#3(Black)

Power ON with 5 minutes
delay after power OFF.
For preventing the over
load of compressor)

Expected causes
Check that if FAN-MOTOR has failure
itself.
Check that if wiring connection has bad
contact.

Check the input of the fan motor rotation

pulse when motor fan operates.

CN75-5(F),6(R),7(C)will generate the pulse signal when motor rotates.
These signals will be inputted into MICOM.
Unless signals are not inputted during motor operating, will be ON 10
seconds after fan Off. But if signals are not still entered, the above operation
will restart four times more.
If signals are not entered continuously, the motor will be restarted after 10
seconds.
This function is effective when the normal operation of motor would be
restrained by foreign matters such as ice.

Checking method of R,F,C FAN Motor voltage
The voltage between PCB typical Ground CN1-"3"(Black) and
R FAN ; CN75#2(Yellow) shall be less than DC 7~12V.
F FAN ; CN75#3(Orange) shall be less than DC 7~12V.
C FAN ; CN75#4(Sky-blue) shall be less than DC 7~12V.

- Recheck if resistance values are different after measuring.

Is the voltage between MAIN

PCB CN1#3 (Black) and CN75#2

(Yellow) around DC7~12V?

Is the voltage between MAIN

PCB CN1#3 (Black) and CN75#3

(Orange) around DC7~12V?

Is the voltage between MAIN

PCB CN1#3 (Black) and CN75#4(Sky

-blue) around DC7~12V?

Is the voltage between MAIN

PCB CN1#3 (Black) and CN30#2

(Purple) around 0V?

Is the voltage between MAIN

PCB CN1#3 (Black) and CN30#1

(Black) around 5V?

Does DC7~12V alternate with

below DC 2V between MAIN PCB

CN1#3(Black) and CN75-#2(Yellow)

Does DC7~12V alternate with below

DC 2V between MAIN PCB CN1#3(Black)

and CN75#3(Orange)

Does DC7~12V alternate with below

DC 2V between MAIN PCB CN1#3(Black)

and CN75#4(Sky-blue)

In initial power to appliance, the compressor
and fans of fresh food/ freezer, compressor
fan operate. If freezer temperature is
sensed of 41

by momentary power

failure, fans will operate after 5 minutes.

Reference

2¢(-19¡) is recommended 38¢(3¡) is recommended

F FAN ERROR

C FAN ERROR

2¢(-19¡) is recommended 38¢(3¡) is recommended

2¢(-19¡) is recommended 38¢(3¡) is recommended

71

TROUBLESHOOTING

4-2-3. If ICE Room Fan does not operate

- This refrigerator has BLDC FAN motor. BLDC motor is driven by DC7~12V.

- When COMP ON, normally operates with F-FAN motor.

- If there is any trouble, you should select the self-diagnostic function to check the trouble before power off.

Start

Execute manual operation

No

Yes

Yes

No

Yes

Yes

No

No

Is COMPRESSOR ON ?

Is the Ice Room

temperature suitable for

the Fan working?

Predicted Cause
FAN-MOTOR troubles itself
Bad wiring connections.
Wrong Input of the fan motor rotation pulse

Reference

CN76 #2 will generate the pulse signal when motor rotates.
These signals will be input into MICOM.
Unless signals are not input during motor operating, will be ON
10seconds after fan OFF. But if signals are not still taken, the
above operation will be retried four times more. If signals are not
taken continuously, the motor will be restarted after 10 minutes.
This function is against the case that motor movement would be
restrained by foreign matters like ice.

Is the voltage between

MAIN PCB CN1-”3”

(Black) and CN76-”1”

(Black) around DC7~12V?

Does DC7~12V alternate

with below DC2V between MAIN PCB CN1-

”3”(Black) and CN75-”2”(Yellow)?

FAN works normally

Operation

temperature/ready

Replace MAIN PCB

FAN pulse voltage

CN76-”2”(Brown)

Typical PCB Ground

CN1-”3”(Black)

Ice Room control temperature

Ice ON

8.6 (-13 )

Ice OFF

26.6 (-3 )

The voltage is variable due to pulse
signal but measured about 2~3V with the
Multi-Meter.

Display for checking the self-diagnostic function

Ice Room FAN ERROR

Checking method of Ice Room FAN Motor Voltage with the voltage between typical
PCB Ground CN1-”3”(Black) and Ice Room FAN ; CN76-”1”(Black) shall be less
than DC 6~12V.

- Additional check if resistance values are different after measurement.

Typical PCB Ground
CN1-”3”(Black)

1) Ice Room - FAN

2¢(-19¡) is recommended 38¢(3¡) is recommended

72

TROUBLESHOOTING

1. Water is automatically supplied to the Ice Maker by temperature & time and Ice Maker Dispenses cubed or
crushed ice.

2. Power is applied to the one end of wires. Be careful when disassembling and shall refer to its exploded diagram
in any case.

3. Ice Maker operation shall be checked after pressing the Ice Maker testing switch.
(Freezer Ice Maker) It is not possible to check when the power is disengaged.

4. We recommend that TWO PEOPLE check the PCB and Ice Maker because hey are located at front and rear
side each.

5. Be careful! The Ice Maker Heater can cause personal injury like burn.

4-2-4. If Ice Maker does not operate

Checking Method of ICE Maker Voltage

With typical PCB Ground CN1-”3”(Black) and

1) Test Switch operation (press selected) : CN90-”5” (Gray) shall be DC 0V.
Test Switch ready ; CN90-”5” (Gray) shall be less than DC 5V.

Checking Method of ICE Maker Voltage

With typical PCB Ground CN1-”3”(Black) and

2) IC02 MICOM #27 voltage ; Ready(0V) Rotate (4.9V) Before
complete(4.9V) Return(0V)
* MICOM #27 voltage is same as Connector CN90-”7”(Purple)

3) IC02 MICOM #28 voltage ; Ready(0V) Rotate (0V) Before
complete(4.9V) Return(0V)
* MICOM #28 voltage is same as Connector CN90-”6”(Blue)

1)Test Switch operating 1)Test Switch ready

typical PCB Ground
CN1-"3"(Black)

Displays ERROR Code

2¢(-19¡) is recommended 38¢(3¡) is recommended

Start

1) Replace the Ice Maker Kit

2) Check/Replace the Main PCB
input signal
(Micom IC02 Pin #29 - “0V”)

Does Ice Maker

rotate when pressing the Ice Maker

testing switch(over 1.5 sec)?

No

1) Check the wiring connections.

2) Replace Ice Maker Kit

3) Replace MAIN PCB

Is the input voltage of IC02

MICOM #27, 28 normal?

No

1) Replace the Water Valve
* Refer to the operation

condition of Water Valve

2) Replace the Main PCB

Is the water supplied in 6

minutes (After sensing ice bucket

fully)?

No

1) Repair the Ice Maker Sensor
* Refer to the solution “If Ice

Maker Sensor has trouble”

No trouble with PCB and temperature sensor,
Check the bad wiring connections.

Is the Ice Maker Sensor unit normal?

No

Operating Condition when motor rotates
Operating Status of Micom(IC02)

Heater operates differently according to
the conditions.
Test Mode operation will be 30 sec.

Operation

5V
5V

Ready

0V
0V

Motor Load (#10)
Heater Load (#9)

MICOM(IC02) Operation Status

#29

(Test Switch)

Operation5VReady

0V

MICOM(IC02) Operation Status

#27

(Blade Ice Scoop)

#28

(Guide Ice Full)

Ready Rotation

Before

Complete

Returning

0V 4.9V 4.9V 0V

0V 0V 4.9V 0V

Check the ICE Maker Heater & Motor Resistance
Resistance value can be changed according to the Voltage and
Perfermance changes.

1) Measuring the Ice Maker Heater
resistance values

CN70-”1” (Red) & CN72-”3” (White)

Resistance value : 91(364)Ohm 7% Resistance value : 3.93(11.76)KOhm 7%

CN70-”1” (Red) & CN72-”1” (Brown)

2) Measuring the Ice Maker Motor
resistance values

Yes

Yes

Yes

Yes

73

TROUBLESHOOTING

- If defrost has trouble, select the self-diagnostic function to detect the error of defrost heater before
Power Off. (Check the function with refer to the self-diagnostic function)

4-2-5. If defrost does not operate (F,R DEF Heater)

R DEF ERROR

2¢(-19¡) is recommended 38¢(3¡) is recommended

F DEF ERROR

2¢(-19¡) is recommended 38¢(3¡) is recommended

Start

Are the all deforst

heater normal?

Check the bimetal, heater
disconnection, wiring connection etc.

Refer to self-diagnostic

function in the manual

Replace the
applicable sensor

manual operation for a certain time

Manual defrosting of fresh food

and freezer compartments

operate simultaneously.

Resistance value of sensor according to temperature

If you need the

temperature with detail,

refer to DATA1.

temperature

table

**Measuring point of resistance value according to sensor **
F-DEF : CN30#4 CN75#1 measuring resistance value
R-DEF : CN30#7 CN75#1 measuring resistance value
** 0 : Short trouble / : Open trouble

**Measuring point of resistance value according to heater**
F-DEF : CN70#9(Brown)

CN71#9(Orange) measuring

resistance value(55(216) ohm

7%)

R-DEF(Ice Pipe parallel) : CN70#7(White)

N71#9(Orange)

measuring resistance value(105(441) ohm

7%)

** 0

: Short trouble / : Open(bimetal, heater) trouble

86

(30 )

68

(20 )

50

(10 )

32

(0 )

14

(-10 )

-4

(-20 )

-22

(-30 )

4.22

6.05

8.87

13.29

20.42

32.23

52.41

If Energy Saver + Fridge Key are pressed
simultaneously for 8 seconds and then select any key,
3rd test mode(manual defrosting) will be operated.

Is the temperature of
defrost sensor lower

than 53.6

(12°C)?

Is defrost sensor by

self-diagnostic normal?

Is power applied to

each defrost heaters?

Is connection terminal of

MAIN PCB part normal?

Recheck the applicable

sensor.

**Measuring point of resistance value according to sensor **
F-DEF : CN30#4

CN75#1 measuring resistance value

R-DEF : CN30#7

CN75#1 measuring resistance value

** 0V: Short trouble / 5V: Open trouble

Normal

Repair connection terminal

Reference If defrost sensor

temperatures of fresh food and
freezer compartments are higher
than 50

(10 ), 53.6 (12 ) by
the heating from heater, heating
would be finished and will return
to cooling operation after a pause.

Check bimetal, heater itself,

disconnection etc.

Replace failure Relay or

replace PCB ASS'Y

Does the system return

to cooling operation after

heating for specified time?

Checking method of F,R DEF Heater resistance value

F FEF ; CN70#9(Brown)

CN71#9(Orange)

R FEF ; CN70#7(White)

CN71#9(Orange)

- Recheck if resistance values are different after the test

1) F DEF Heater 2) R DEF Heater

74

TROUBLESHOOTING

4-2-6. If Power is not supplied

Caution

At the power of main PCB, the
AC115(220)V power and a high­voltage over DC 170(325)V are
occurred.Please take care of
yourself on repair and measurement.

Check in SMPS PBA

Start

- Refer to function and
reference parts in the manual
when check the MAIN PCB

Connect plug again,
check the plug loosening

Check the assembly and wire
connection

1) Replace FUSE AC 250V 2.0A

2) Replace SMPS assembly

Replace PCB ASS'Y

1) Replace U4 (D10LC20U)

2) Replace PCB ASS'Y

1) Replace REG1 (KA7805)

2) Replace PCB ASS'Y

1) Check assembly wire and repair

2) Replace Panel PCB

1) Solder again

2) Replace PCB MAIN

- Check MAIN PCB connection

- Check the connections
between cabinet to door

- Check the connections
between door to panel PCB

1) Check the contact of lead wire

2) Replace the applicable relay / PCB MAIN

1) Check PCB PATTERN and replace BD1

2) Replace PCB ASS'Y

Is plug connected in?

Is power 115(220)V

both terminals of SMPS

PCB CN1?

Is fuse on the SMPS

PCB down?

Is DC170(325)V

applied both

terminals of BD1+,-

Is DC5.8V

applied between TOP

switch 246Y C to S?

Is 12V applied both

terminals of C16?

Is 5V applied both
terminals of C19?

Does Panel PCB

operate normally?

Is normal load such

as Relay?

Is there any PCB

soldering, short,

breakage?

Normal(Recheck)

Checking method of SMPS voltage CN1
input ; CN1#1(Red) #3(Black) AC voltage

Checking method of SMPS 2nd output
voltage CN2 input ; CN2#1(Red)
#3(Black) same as C19 terminals..
DC 5V 0.3V

Checking method of SMPS 2nd output
voltage CN2 input ; CN2#5(Yellow)
#3(Black) same as C16 terminals.
DC 12V 0.6V

75

TROUBLESHOOTING

4-2-7. If compressor does not operate

Start

Did 5 mins pass

after Compressor

OFF ?

Does compressor work
with manual operation?

Is IC02 MICOM #8

High?(5V)

normal

Is IC72 #15 about

0.8V?

Is CN71 connector

normal?

Is COMP ASS'Y

normal?

Normal (recheck)

Replace COMP ASS'Y

Check bad contact of

connector

Check after

5 minutes

Refer to test function

in the manual

1) Replace MICOM

2) Replace PCB

Refer to circuit diagram
in the manual

1) Replace IC72 Driver IC(TD62083AP)

2) Replace PCB

Did buzzer of manual operation sound?
(Check certainly after manual operation)

Checking method of voltage PCB typical
Ground CN1#3(Black) and

1) IC02 MICOM #8 ; voltage High(5V 0.5V)
IC02 MICOM #8, COMP operating

Checking method of voltage
PCB typical Ground CN1#3(Black) and

1) IC72 #15 : Voltage Low(0V)

typical PCB Ground
CN1#3(Black)

76

TROUBLESHOOTING

4-2-8. When alarm sound continuous without stop(related with buzzer sound)

Start

Door is ajar

Start

Is door closed

completely?

Is water penetrated

into the door switch?

Is the connector(CN30)

inserted correctly?

Is manual operation

/defrost selected?

Does buzzer sounds

when power On again?

Is the door switch unit

normal?

Is the input

voltage of main #50 and #3

changed at door-open,

door-close?

If 'ding-dong' sounds continuously

If 'beep-beep' sounds continuously

Remove causes after comprehending
the conditions of interference by door
gasket, food etc.

Replace Door S/W

Replace Door S/W

MAIN PCB normal

Check if there is any short parts
due to foreign matters and the
test jumper part in the main­PCB.

Recheck MAIN PCB and

door switch

Separate the door switch and check if
the measured value of unit is
changed from 0 to according
to switch ON/OFF.
* FF Door Switch is magnetic switch .
(it can be operated when door
magnet is combined with)

Repair wire connection and
Door S/W

Connector is not inserted,
Repair bad contact

Enforce the cancelation the
manual operation/ defrost function
or power On after power Off

Door & MICOM State

DoorFMICOM

(#50)

Close
Open

5V(High)

0V(Low)

0V(Low)

5V(High)

R MICOM(#3)

Right and Left

77

TROUBLESHOOTING

If buzzer does not sound

Buzzer is installed on the panel PCB in this model.
If buzzer does not sound when button is pressed, manual operation is started and door is opened,
should separate panel PCB and check the breakage of buzzer and bad soldering.
It is very hard to repair the panel PCB because it consists of SMD assemblies.
It is recommended to replace assembly PCB when the failure associated with panel is occurred
except the minor error such as switch pressing error, surface peeling off and so on.

Start

Does it sound

'dingdong' if press a button

on the front panel?

Is the damage

or breakage of the buzzer in

the panel PCB?

Did lead of a component

fall on the vibration plate of

buzzer?

Does it make a

sound of 'dooropen' alarm when

you are opening the door of freezer or

fridge more than 2 minutes?

MAIN PCB normal,
BUZZER normal

Check the panel PCB with reference
of <how to check Panel Display>

Replace(repair) buzzer
Replace Panel PCB

Replace buzzer
Replace Panel PCB

Recheck the button pressing
force and mechanical problem

78

TROUBLESHOOTING

4-2-9. If Panel PCB does not work normally

When lighting of Panel PCB is disabled or only some LED Lamp are disabled

Be careful to repair because display of this model is installed in the MICOM of internal PCB.
It is recommend to replace PCB MAIN after checking except specified solder touch.

Start

Is the connector of

upper hinge cover
inserted correctly?

Is MAIN PCB
connector (CN50)
inserted correctly?

Is Upper Hinge

Panel PCB connector

inserted correctly?

Is lighting operate

normally when replace

Panel-PCB?

Are one or more keys

pressed continuously?

Is the PCB system

still operated by separating

of the mechanism?

Is the lighting operated

normally when replace the

Panel-PCB ?

Refer to electronic circuit
diagram in the manual or
circuit diagram on the back
side of the appliance

Reinsert connector,
Repair bad contact

Reinsert connector of MAIN PCB

Reinsert connector,
Repair bad contact

Panel PCB itself has trouble.

Reassemble the PCB ASS'Y /
Enforce the cancelation of pressed keys

Reassemble the PCB ASS'Y /
Enforce the cancelation of pressed keys

Panel PCB itself has trouble.

Check the wire of Dispenser part - Upper Hinge Panel - disconnection, short between wires
Check the wires between fresh food compartment upper cabinet - MAIN PCB - disconnection, short between wires

Check the wires of Dispenser part - Upper Hinge Panel - disconnection, short between wires.
Check the wires of fresh food compartment upper cabinet - disconnection, short between wires.
Check the short/open of the panel communication and power supply circuit in MAIN PCB.

If Panel PCB KEY is not selected
If it is not repaired with using the basic checking method as above

79

TROUBLESHOOTING

4-2-10. If Pantry Panel PCB is not working normally

You should check the display after door opening because the display of this model operates only when
the fresh food compartment door is opened.

Start

Does fresh food

compartment door switch

operate normally?

Is the connector of

pantry room in fresh food

compartment inserted

correctly?

Is MAIN PCB

Connector (CN78) inserted

correctly?

Is signal of MAIN

PCB CN78 normal?

Is the lighting

operated when replace Pantry

Panel-PCB?

Is a key pressed

continuously?

Is the PCB system

still operated by separating

of the mechanism?

Is the lighting operated

when replace Pantry

Panel-PCB?

Is a normal voltage

outputted from MAIN PCB IC74

in the key operating?

Check and repair the switch
* Refer to<how to repair door switch>

Reinsert Connector,
Repair bad contact

Reinsert connector in MAIN PCB

Check voltage/Replace MAIN PCB

Panel PCB itself has trouble.

Reassemble PCB ASS'Y /
Enforce the cancelation of
pressed keys

Reassemble PCB ASS'Y /
Enforce the cancelation of
pressed keys

Convertible compartment Panel
PCB itself has trouble.

Replace MAIN PCB
Check the short of MAIN
Panel wire

Check the wires of Pantry Room - disconnection, short between wires
Recheck the control circuit of MAIN PCB Pantry Panel
Check the wire assembling between Panel MAIN

Check the wire of Pantry Room - disconnection, short
between wires
Check the short/open of the pantry panel lighting
circuit in MAIN PCB.

If Panel Panel PCB Key is not selected

If Panel Key is not selected

If it is not repaired with using the basic checking method as above

typical PCB Ground
CN1#3(Black)

Checking method of voltage Based on
PCB typical Ground CN1#3(Black)

1) Key voltage ; CN78#1"(Purple)

2) LED part voltage ; CN78-"7"(Yellow),
"8"(Pink)

Voltage of CN78 is same as

IC74 #13,#11 voltage.

1) select(operating) (0V)

2) normal(about5.0V

0.5V)

- Display On (0.7V 0.3V) - Display Off (9.7V 1V)

80

TROUBLESHOOTING

4-2-11. When refrigerator ROOM Lamp does not light up

1. When you replace the lamp of freezer, please power OFF to avoid an electric shock.

2. Please keep in mind you could get burnt by the excessive heating of an incandescent light bulb.

3. Bimetal is installed in the refrigerator LAMP. Check that if LAMP may be OFF by bimetal.

The case of fresh food compartment(room) lamp will be explained only.
Because it is possible to repair the other room lamps with the same method.

Start

Is the inside lamp

filament cut?

Is Lamp OFF by

bimetal operating?

Is the connection

point of R-door switch

normal?

Is the control relay

of the inside lamp in PCB

normal?(RY76)

Repair the inside lamp

Fresh food compartment
Lamp is applied only.

Repair door switch

Replace PCB and
Replace Relay

Check the connection of RDoor
switch and repair the inside lamp
socket

Reference

* The interior lamp relay operates lighting/lightout

according to door open / close.

* If interior lamp does not light, check the noise of relay

operation.

* Noise of relay operation sounds every Door Open /

Close.
* F-LAMP Relay -- RY75
* R-LAMP Relay -- RY76

Reference
If the door is opened, the contact of door switch will be opened and MICOM will get applied 5V to finally sense Open.
If 5V has been sensed over two minutes afterwards, Door-Open alarm will sound

Ding-Dong for 10 seconds in a oneminute cycle. For
that reason, if the door switch has failure, the refrigerator can make a Ding-Dong sound per a oneminute cycle. Please note the step
for its service.

Wait for returning time
of bimetal

When measure lamp resistance to the Wire
Resistance can be changed by Lamp input voltage.
(Actual measurement is below, it can be changed by
performance)

Checking method of Door Switch voltage

- Measuring voltage of Sensor Check Point #5(IC01 MICOM #58) on
PCB or CN30#8(White-black) CN75#1(Gray)

- Compare time table after measuring

Measuring voltage of CN30#8(white-black)

CN75#1(Gray) are below

Fresh food
compartment lamp
CN70#1(Red)
CN71#1 (Blue) ;
10(33)Ohm 3 Ohm
Lamp ; 60W + 60W

Freezer
compartment lamp
CN70#1(Red)
CN71#3 (Gray) ;
15(66)Ohm

5 Ohm

Lamp ; 60W

typical PCB Ground CN10#3"(Black)

Door & MICOM State

Door

F

MICOM

(#50)

Close
Open

5V(High)
0V(Low)

0V(Low)

5V(High)

R MICOM(#3)

Right and Left

81

TROUBLESHOOTING

4-2-12. If ICE Water is not supplied

Start

Is the confirming sound of

the valve operation heard when

Ice maker test switch pushed?

Does Main PCB MICOM

#12 have high (5V)output?

Does Main PCB IC73

#13 have about 0.7V

output?

Is the contact point of main

PCB RELAY RY79 normal?

MAIN PCB normal

-- Need to check the other parts
Check the wire between Ice
water valve MAIN PCB
Ice water valve itself has trouble
or bad contact of connector
Check the connection hose

Normal(Check Ice
water valve hose)

Check soldering
short/Replace PCB

Check soldering
short/Replace PCB

Check soldering
short/Replace PCB

typical PCB Ground CN1#3(Black)

Checking method of voltage Based on
PCB typical Ground CN1#3(Black)

1) Check the voltage of IC73#4(same voltage
as IC02 #12)

- ICE Water valve operating (about 5V 0.5V)

Based on PCB typical Ground CN1#3(Black)

2) IC73 #13 voltage

- ICE Water valve operating (about 0.7V 0.5V)

3) Check the voltage of ICE Water Valve

operating(AC voltage)
=> For checking the Relay RY79 operating.
CN70#1(Red) CN73#7(Purple)

- ICE Water valve waiting (about AC 0V)

- ICE Water valve operating (about AC 110(220)V 20%)

82

TROUBLESHOOTING

4-2-13. If Water is not supplied

Checking method of Valve resistance (Must

power off for checking)
Resistance can be changed by input voltage.
CN70#1 (Red) CN73#5 (White-black)

- resistance value ; 388(1.6k)Ohm 7%)
** 0 : Short trouble / : Open trouble

Start

Is the confirming sound of

the valve operation heard

when dispenser switch

pushed?

Is the valve unit normal?

Is the voltage of PCB IC01

MICOM #15 changed 0V~5V

according to switch On/Off?

Does Main PCB IC73 #3

have about 5V input?

Does Main PCB IC73 #14

have about 0.7V output?

Is the contact point of main

PCB RELAY RY7A normal?

MAIN PCB normal

-- Need to check the other parts
Check the wire between water valve
MAIN PCB
Ice water valve itself has trouble or bad
contact of connector
Check the connection hose
Check the operation between Panel PCB
and MAIN PCB for Communication.

Normal(Check Ice
water valve hose)

Replace Valve

Check soldering
short/Replace PCB

Check soldering
short/Replace PCB

Check soldering
short/Replace PCB

1) Check the dispensing
lever

2) Check switch unit/ wiring
connection

3) Replace PCB

typical PCB Ground CN1#3(Black)

Checking method of voltage

Based on PCB typical Ground CN1#3(Black)

1) Check voltage of IC73# (same voltage as
IC01#64)

- Water valve operating (about 5V

0.5V)

Based on PCB typical Ground CN1#3(Black)

2) IC73 #14 voltage

- Water valve operating (about 0.7V

0.5V)

3) Check the voltage of Water Valve operating
(AC voltage)

=> For checking the Relay RY7A operating.
CN70#1(Red)

CN73#5(White-black)

- ICE Water valve waiting (about AC 0V)

- ICE Water valve operating (about AC 110(220)V 20%)

TROUBLESHOOTING

4-2-14. If Cubed or Crushed Ice is not supplied

83

Start

Check the Ice making switch
Check the DOOR Switch
Check the Ice movin motor
Check the wiring connections of Ice moving motor
Check if the COVER ICE ROUTE opens
Check the Q706 movement related with
AUGER_MOTOR safety

Check the water pipe
: bending / Shut off

heck route of ice check solenoid

Check he Ice Maker wiring

Freezer door shall be
closed during operaion.

If MAIN PCB is normal

- Need to check the other parts
AUGER MOTOR MAIN PCB
Check the door wiring connections.
CUBE MOTOR MAIN PCB
Check the door wiring connections/trouble their own or bad wiring connections.

Normal Operation status

Are Ices ejected?

Which mode is

selected?

Is Cubed Ice ejected?

No

Cubed Ice ejected

Crushed Ice

Cubed Ice selected

Is Cubed Ice mode

selected on the

panel PCB?

No

Cubed Ice

No

Yes

Yes

Yes

Yes

Yes

Yes

Check the wire connections/

Cube Solenoid

Is the CUBE MOTOR

positioned at cubed

ice mode?

No

- Check the Ice switch has trouble itself

- Check the wire connections

- Replace the MAIN PCB

Is MICOM IC01 #15

change into 0V when

press Ice switch?

No

check the WIRE & Motor/

Replace the MAIN PCB

Is the Dispenser

Cover opened?

No

Replace the MAIN PCB

(Errors on IC73)

Is IC73 #1,2 changed

into 5V when pressing

Ice Switch?

No

- RY7B, RY7C RELAY Error

- Replace the MAIN PCB

After disconnecting the
CN70, CN71, CN72 and
CN73, measure the both
ends of contact points of
RY7B, RY7C

After disconnecting the
CN70, CN71, CN72 and
CN73, measure the both
ends of contact points of
RY7B.

Is the contact

point of RY7B & RY7C RELAY

changed into 0

No

No

No

Yes

Yes

No

Yes

Yes

Yes

Yes

Yes

Yes

No

No

No

No

No

Normal Operation status

Cancel the “Ice Off”

Is Crushed Ice ejected?

Crushed Ice selected

Is Crushed Ice mode

selected on the

panel PCB?

Check the wire connections/

Motor Cube

Is the CUBE MOTOR

positioned at cubed

ice mode?

- Check the Ice switch has trouble itself

- Check the wire connections

- Replace the MAIN PCB

Is MICOM IC01 #15

change into 0V when

press Ice switch?

check the WIRE & Motor/

Replace the MAIN PCB

Is the Dispenser

Cover opened?

Replace the MAIN PCB

(Errors on IC73)

Is IC73 #2 changed

into 5V when pressing

Ice Switch?

- RY7B RELAY Error

- Replace the MAIN PCB

Is the contact

point of RY7B RELAY

changed into 0

Are Ices in the Ice bucket?

Is “Ice Off” mode

selected on the display

panel?

No

84

TROUBLESHOOTING

4-2-15. If Cover Ice Route Moor(Geard Motor) is not working normally

Start

Replace the MOTOR

Does GEARED MOTOR

work properly?

No

Yes

Cubed or Crushed Ice is selected
on the LED PANEL PCB

Is Cubed or Crushed

Ice mode selected on the

LED PANEL?

No

Yes

Select the DISPENSER switch

Is the DISPENSER

switch selected?

No

Yes

Check the WIRE

Does the wiring at the

both side of motor connected

properly?

No

Yes

When the MOTOR
rotates.

Check the MOTOR/Check any
interference on MOTOR rotation

Check CN70 , CN73 , voltage is applied to the PCB CASE.
Check the SSR73 SHORT/OPEN of Cover Ice Motor control circuit in the MAIN PCB.
Check any SHORT/OPEN of wiring connections between PCB CASE and MAIN PCB.
(CN70

, CN73 )

NOTE. <Make sure that the plug is tuned off before you work, Check the Resistance value>

Caution

1. When replacing the Cover Ice Motor, pull out the plug to avoid an electric shock.

2. Be careful! When disassemble the Cover Ice Motor, spring can jumped out and may cause personal injury.

3. Motor will rotate continuously when the Motor Switch is not sensed.

Main PCB - Check the wire OPEN/SHORT between the Cover Ice Motor Rotation sensin switches.
Check the Short of Cover Ice Motor Control Circuit SSR73 in the MAIN PCB.
Replace the MAIN PCB or the Dispenser Cover Motor.

Is the AC input voltage

applied to the both ends

of the motor?

Yes

No

Check/Repair the Housing
connector

Is the sensing

SWITCH connection

normal?

No

Yes

Check/Repair the Motor Rotation
pressing area

Is the switch

pressed area normal when

motor rotates?

No

Yes

Normal

Are the voltage

CN10-”3” and CN50-”9”,

“10” normal?

Yes

No

Operating Condition of Dispenser
Open/Close
CN50 - Switch 1,2 Operating

OpenClose

Ice Route Switch 1
CN50 - “9” (Purple)

Ice Route Switch 2
CN50 - “10” (White)

0V

0V

0V

0V

Checking Mehod of Cover Ice
Route Motor Resistance
(Make sure to work after Power Off)
The Resistance is variable
according to the input voltage.

85

5 . EXPLODED VIEW& PARTS LIST

5-1) FREEZER 86

5-2) REFRIGERATOR 89

5-3) CABINET 93

5-4) DISASSEMBLY OF FREEZE DOOR 97

5-5) DISASSEMBLY OF REFRIGERATOR DOOR LEFT 99

5-6) DISASSEMBLY OF REFRIGERATOR DOOR RIGHT 102

RF267AA

86

EXPLODED VIEW& PARTS LIST

5-1) Freezer

1-6

6-1

6-2

7-3

7-4

8-4

19-2

19-5

19-6

19-7

19-7

19-3

19-4

19-1

19-1

19-12

19-8

19-19

19-9

19-18

19-16

19-20

19-11

19-21

19-22

19-23

19-17

19-11

19-13

19-14

19-15

19-13

19-10

8-3

10-3

18-3

18-2

18-1

13-3

13-1

13-2

10-2

10-4

10-1

8-2

8-1

7-2

7-1

6-3

1

6

2

3

7

9

10

11

12

13

14

17

5

16

17

18

19

15

8

4

1-3

1-4

1-8

1-7

1-5

1-2

1-1

20-2

20-1

20

87

EXPLODED VIEW& PARTS LIST

NNOO

1
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8

2

3

4

5

6
6-1
6-2
6-3

7
7-1
7-2
7-3
7-4

8
8-1
8-2
8-3
8-4

9

10
10-1
10-2
10-3
10-4

11

12

13
13-1
13-2
13-3

14

15

16

17

18
18-1
18-2
18-3

19
19-1
19-2
19-3
19-4

QQUUAANN

TTIITTYY

1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
6
2
1
1
6
8
1
1

CCOODDEE--NNOO

DA96-00399C

6501-000123
DA32-00027B
DA47-00243R
DA47-00244C
DA59-00361A
DA61-02901A
DA61-03187B
DA61-03644A
DA63-02902B
DA63-03420A

4713-001223
DA63-03696A
DA97-05354A
DA63-03435A
DA63-03436A
DA63-03697A
DA97-04834B

6002-000458
DA61-03334A
DA63-40167A
DA63-03416A
DA97-04833B

6002-000458
DA61-03159A
DA63-40167A
DA63-03417A
DA63-03414A
DA97-04836A
DA34-00047A
DA61-03154A
DA61-03158A
DA66-00436A
DA66-00437A
DA67-00859C
DA97-04835A
DA61-03154A
DA61-03333A
DA66-00435A
DA63-03415A
DA61-03190A
DA34-10120E
DA61-03416A
DA97-04848A

6002-000213
DA61-03160A
DA63-03418A
DA97-05343B

6002-000213

6002-000215
DA31-00124A
DA31-00146C

SSVVCC--CCOODDEE

RO101

RI074

RF030

RI157

RF026

RF031

RI081
RI064

RI064
RI062
RI064
RI177

RS059

RI187
RI220
RI225
RI178

RS059

RI188
RI220
RI226
RI223
RI171

RO151

RI170
RI184
RI242
RI244

RD059

RI173
RI170
RI185
RI243

RI224
RF122
RF041

RI218

RI227

RS047

RI181

RI237

RS047
RS080

RI085

RI089

RREEMMAARRKKPPAARRTT NNAAMMEE

ASSY EVAP-FRE ICE
CABLE TIE
SENSOR ASSY

THERMO BIMETAL-PROTECTOR

HEATER-METAL SHEATH
EVAP FRE,ICE
FIXER-SENSOR EVAP
PLATE-DRAIN FRE
PLATE-EVAP HEATER
COVER-FIXER HOUSING,V
COVER-LAMP FRE
LAMP INCANDESCENT
TRAY-FREE UPP SUB
ASSY TRAY-FRE UPP
COVER-TRAY FRE UPP A
COVER-TRAY FRE UPP B
TRAY-FRE UPP
ASSY RAIL-SLIDE UPP L
SCREW-TAPPING
RAIL-SLIDE UPP L
GROMMET-COVER SLIDE
COVER-RAIL UPP L
ASSY RAIL-SLIDE UPP R
SCREW-TAPPING
RAIL-SLIDE UPP R
GROMMET-COVER SLIDE
COVER-RAIL UPP R
COVER-RAIL LOW L
ASSY RAIL-SLIDE LOW L
SWITCH PRESSURE
FIXER-GEAR
RAIL-SLIDE LOW L
GEAR-L
SHAFT-GEAR
CAP-DOOR HANDLE
ASSY RAIL-SLIDE LOW R
FIXER-GEAR
RAIL-SLIDE LOW R
GEAR-R
COVER-RAIL LOW R
FIXER-TRAY FRE UPP
SWITCH DOOR-F
GUIDE-DRAWER BOX
ASSY TRAY-DRAWER BOX
SCREW-TAPPING
REINF-DRAWER BOX
TRAY-DRAWER BOX
ASSY COVER-EVAP FRE ICE
SCREW TAPPING
SCREW TAPPING
FAN AX100W4CC T1
MOTOR DC BLDC

SSPPEECC

AW-PJT(BEST,GE),115V,240W
DACT140,W3.6,L146,NTR,NYLON66

502AT,AW-PJT,-40~110?,5V,R-DEF-SENSOR,YEL,400MM
AW-PJT(F),BT-121-M, PW-5M1N,125 / 250V,10 / 5A,60?,40?,100MΩ

AW-PJT,240W,115V,55.1,F-ROOM
PIN,115V,AW-PJT
CORE-PJT,PP,NTR
AW-PJT,GALVANUME,T0.3
AL,T0.7
NEXT,GALVALUM,T0.3
AW,GPPS,NTR
120V,500mA,60W,47x84mm
AW-PJT,SAN
AW-PJT
AW-PJT,HIPS,COOL WHITE
AW-PJT,GPPS
AW-PJT,HIPS,COOL WHITE
AW-PJT
FH,+,1,M4,L14,ZPC(WHT),SWRCH18A
AW-PJT,STS430
T3.0,SILICON,NTR
AW,HIPS,COOL WHITE
AW-PJT
FH,+,1,M4,L14,ZPC(WHT),SWRCH18A
AW-PJT,STS430
T3.0,SILICON,NTR
AW-PJT,HIPS,COOL WHITE,
AW-PJT,ABS,COOL WHITE
AW-PJT
AW-PJT,HIPS,COOL WHITE
AW-PJT,POM,NTR
AW-PJT,STS430
AW-PJT,POM,NTR
AW-PJT,SM25C
CORE,POM,-,-,-,INOX,SC-06034R
AW-PJT
AW-PJT,POM,NTR
AW-PJT,STS430
AW-PJT,POM,NTR
AW-PJT,ABS,COOL WHITE
AW-PJT,PP,NTR
slide,250V,0.5A,cool white
AW-PJT,HIPS,COOL WHITE
AW-PJT
TH,+,1,M4,L12,ZPC(WHT),SWRCH18A
AW-PJT,SECC1,T3.0,COOL WHITE
AW-PJT,PP,COOL WHITE
AW-PJT(RF267,GE)
TH,+,1,M4,L12,ZPC(WHT),SWRCH18A
TH,+,1,M4.0,L16,ZPC(WHT),SWRCH18A
FAN-AX100W4CC-T1
DC12V,150mA,2.1W

■■

Parts List of Freezer

88

EXPLODED VIEW& PARTS LIST

NNOO

19-5
19-6
19-7
19-8

19-9
19-10
19-11
19-12
19-13
19-14
19-15
19-16
19-17
19-18
19-19
19-20
19-21
19-22
19-23

20
20-1
20-2

QQUUAANN

TTIITTYY

1
1
2
1
2
2
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1

CCOODDEE--NNOO

DA61-03183A
DA61-03618A
DA61-20128A
DA62-01527A
DA63-01146A
DA63-01808A
DA63-01809A
DA63-03740A
DA63-40167A

DA96-00042J
DA96-00042H
DA67-01774A
DA61-03724A
DA47-00261A
DA61-03627A
DA31-00146E
DA31-00123A
DA61-03617A
DA62-01526A
DA97-02019B
DA63-10467B
DA32-00011U

SSVVCC--CCOODDEE

RF120

RW716

RO138
RO137

RF083

RI087
RI133
RI133

RF038

RI150

RI021
RI021

RREEMMAARRKKPPAARRTT NNAAMMEE

CASE MOTOR FRE
PLATE INS EVAP FRE ICE
SPRING ETC FAN
INSULATION COVER EVAP FRE ICE
GORMMET MOTOR REAR
GORMMET MOTOR FRONT
COVER MOTOR BLDC
COVER EVAP FRE ICE
GROMMET COVER CHIL
WIRE HARNESS MOTOR
WIRE HARNESS MOTOR ICE
DUCT ICE SUB
PLATE DRAIN ICE
HEATER DUCT FRE
PLATE DRAIN FAN
MOTOR FAN BLDC
FAN BACKWARD
CASE MOTOR FRE ICE
SEAL COVER EVAP FRE
ASSY-COVER SONSOR
COVER-SONSOR
SENSOR TEMP

SSPPEECC

AW-PJT,BUBBLE PP
GALVALUME,T0.3
STS304,PI7.8,-,OD1.0
FOAM-PS
NBR,-,-,-,ID6.5,OD42
NBR,BLACK
PP,NTR
PP(BJ-730)
SILICON
R-Fan/ F-Fan
Ice-room Fan
PP(BJ-730)
GALVALUME,T0.3
4W,-,115V,3306Ω
AL,T0.8
DREP5020LB
ABS(HP-0760)
PP(BJ-730),WHITE
FOAM-PE+AL,-,T2,W147,L640

HIPS,SC-02740R,COOL WHITE
PX-41C,AW-PJT,-40~110?,5V

■■

Parts List of Freezer

89

EXPLODED VIEW& PARTS LIST

5-2) Refrigerator

1-3

1-6

1-2

1-1

1-4

1-7

1-8

1-5

1

2

3

3-9

3-12

3-7

3-13

3-8

3-11

3-10

3-17

3-20

3-18

3-3

3-6

3-21

3-16

3-2

3-1

3-14

3-4

3-19

3-5

3-15

4-2

4-1

4-5

4-3

4-4

11-3

11-2

11-5

11-7

11-6

11-4

11-1

12-2

12-1

10-1

31-4

31-1

31-5

31-6

31-3

10-2

13-2

15-1

15-2

15-4

15-3

20-2

20-3

20-1

20-4

17-2

18-2

18-3

18-1

25-2

26-4

26-2

26-5

27-6

27-2

27-3

27-1

27-4

27-5

26-3

25-3

25-1

17-1

17-3

17-4

17-5

13-1

11-8

6

5

7

8

10

30

31

32

11

12

13

15

16

17

20

21

37

34

22

23

29

24

26

28

27

25

18

9

4

14-2

14-1

14-4

14-3

19-3

19-2

19-1

19

31-2

36

35

35-8

35-7

35-1

35-2

35-11

35-3

35-4
35-5
35-6

35-10

35-9

33

33-1

33-2

33-3

33-4

33-7

33-8

33-9

33-11

33-12

33-15

33-16

33-14

33-13

33-5

33-6

33-10

90

EXPLODED VIEW& PARTS LIST

NNOO

1
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8

2

3
3-1
3-2
3-3
3-4
3-5
3-6
3-7
3-8
3-9

3-10
3-11
3-12
3-13
3-14
3-15
3-16
3-17
3-18
3-19
3-20
3-21

4
4-1
4-2
4-3
4-4
4-5

5

6

7

8

9

10
10-1
10-2

11
11-1
11-2
11-3
11-4
11-5

QQUUAANN

TTIITTYY

1
4
1
1
1
1
1
1
1
1
1
3
4
1
1
1
1
2
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
2
1
1
1
4
1
2
1
1

CCOODDEE--NNOO

DA96-00365D

6501-000123
DA32-00027B
DA47-00243S
DA47-00244D
DA59-00357B
DA61-03683A
DA61-03188A
DA61-03644A
DA63-02902B
DA97-04939G

6002-000213

6002-000215
DA31-00124A
DA31-00146C

DA96-00042J
DA61-03181A
DA61-03182A
DA61-03186A
DA61-20128A
DA62-01381A
DA62-01382A
DA62-01383A
DA62-01423A
DA63-01146A
DA63-01808A
DA63-01809A
DA63-03430A
DA63-03517A
DA63-40167A
DA64-02065A
DA61-03599A
DA97-04842C
DA32-00006T
DA61-03163A
DA61-03169A
DA47-40001D
DA47-00243D
DA63-03773A

4713-001223
DA61-03180A
DA97-05545A
DA67-01688A
DA97-04896A
DA67-01607A
DA97-04870A
DA97-05382A

6002-000213
DA01-00400B
DA61-03166A
DA61-03173A
DA63-03761A

SSVVCC--CCOODDEE

RI016

RO101

RI074

RF030

RI016

RF026

RI008
RS047
RS080

RI085

RI089

RI133
RF121

RI210

RI141

RW716

RI231

RI233

RI232

RI236

RO138
RO137

RF083

RI008

RI240

RI087

RI241

RI246

RI139

RI119

RI151

RI074

RI081

RS047

RI208

RI209

RI010

RREEMMAARRKKPPAARRTT NNAAMMEE

ASSY EVAP-REF
CABLE TIE
SENSOR ASSY
THERMO BIMETAL-PROTECTOR
HEATER-METAL SHEATH
EVAP REF
FIXER-SENSOR
PLATE-DRAIN REF
PLATE-EVAP HEATER
COVER-FIXER HOUSING,V
ASSY COVER-EVAP REF
SCREW-TAPPING
SCREW-TAPPING
FAN-AX100W4CC-T1
MOTOR BLDC
WIRE HARNESS-MOTOR
CASE-MOTOR REF
GUIDE-INS EVAP REF
PLATE-INS EVAP REF
SPRING ETC-FAN
INSULATION-EVAP REF
INSULATION-EVAP REAR
INSULATION-EVAP SUB
INSULATION-EVAP DUCT
GROMMET-MOTOR,REAR
GROMMET-MOTOR,FRONT
COVER MOTOR-BLDC
COVER-EVAP REF
COVER-EVAP REF SUB
GROMMET-COVER CHIL
TRIM-COVER EVAP REF
PLATE-HOUSING REF
ASSY CASE LAMP-REF
SENSOR TEMP-R
CASE-LAMP REF
PLATE LAMP REF
LAMP HOLDER ASSY
THERMO BIMETAL PROTECTOR
COVER-LAMP REF
LAMP INCANDESCENT
ANGLE-SHELF REF SIDE
ASSY ANGLE SHELF REF
CAP-ANGLE
ASSY SHELF GLASS REF SLIDE
SHELF GLASS REF SLIDE
ASSY SHELF HANGER SLIDE
ASSY COVER-VEG
SCREW-TAPPING
GLASS-COVER VEG
FIXER-COVER VEG
REINF-COVER VEG
COVER-VEG REF

SSPPEECC

AW-PJT(BEST,GE),115V/120W
DACT140,W3.6,L146,NTR,NYLON66

PX41C,502AT,AW-PJT,40~110,5V,RDEF SENSOR,YEL,400MM
AW-PJT(R),BT-121-M, PW-5M1N,125 / 250V,10 / 5A,60?,40?,100MΩ

AW-PJT,120W,115V,110.2?,RROOM
AW-PJT
ATOP,EVAP,PP,NTR,ALL
AW-PJT,GALVANUME,T0.4,
AL,T0.7
NEXT,GALVALUM,T0.3
AW-PJT(BEST)
TH,+,1,M4,L12,ZPC(WHT),SWRCH18A
TH,+,1,M4.0,L16,ZPC(WHT),SWRCH18A
TD-PJT,ABS
2950,DC12V,150mA,2.1W,MOTORBLDC
ATOP,351510410,N00909204,BLDC,R,FFAN
AW-PJT,BUBBLE PP,NTR
AW-PJT,ABS,NTR
AW-PJT,GALVANUME,T0.4
STS304,PI7.8,OD1.0,FD
AW-PJT,FOAMPS
AW-PJT,FOAMPS
AW-PJT,FOAMPS
AW-PJT,FOAMPS,T20,W44.5,L45
ATOP,NBR,ID6.5,OD42,BLK,BLDC
BLDC,NBR,BLACK,H20
BLDCNEW,PP,NTR,BJ730
AW-PJT,HIPS
AW-PJT,HIPS(HG1760SF),COOL-WHT
T3.0,SILICON,NTR
AW-PJT,ABS,COOL-WHITE
GALVALUME,T0.3
AW-PJT
PX-41C, 502AT,AW-PJT,-40~1
AW,HIPS,COOL WHITE
AW,SBHG1,T0.4
E26,250V,660W,TE5006F

AW-PJT(R-Lamp),BT-121-M, PW-5M1N,125 / 250V,10 / 5A,60?,40?,100MΩ

AW,PC,CRYSTAL
120V,500mA,60W,47x84mm
AW,SECC1,T2.0,COOL-WHITE
AW,SECC1,T2.0,COOL-WHITE
AW-PJT,HIPS,COOL-WHITE

PP+GLASS,COOL WHITE

AW-PJT
TH,+,1,M4,L12,ZPC(WHT),SWRCH18A
756*343,T3.2,1° PRINT
AW,HIPS,COOL-WHITE
AW-PJT,SHP1,T2.9,BLACK
AW,HIPS,COOL-WHITE

■■

Parts List of Refrigerator

91

EXPLODED VIEW& PARTS LIST

NNOO

11-6
11-7
11-8

12
12-1
12-2

13
13-1
13-2

14
14-1
14-2
14-3
14-4

15
15-1
15-2
15-3
15-4

16

17
17-1
17-2
17-3
17-4
17-5

18
18-1
18-2
18-3

19
19-1
19-2
19-3

20
20-1
20-2
20-3
20-4

21

22

23

24

25
25-1
25-2
25-3

26
26-1
26-2
26-3
26-4

QQUUAANN

TTIITTYY

2
2
2
1
1
1
1
1
1
1
1
1
2
2
1
1
1
2
2
1
1
2
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
1
2
1

CCOODDEE--NNOO

DA64-00817A
DA66-00438A
DA66-10104A
DA97-04839A
DA61-03172A
DA66-10104A
DA97-04840A
DA61-03177A
DA66-10104A
DA97-04846A
DA61-03165A
DA63-03426A
DA66-10104A
DA71-20145A
DA97-05381A
DA61-03652A
DA63-03760A
DA66-10104A
DA71-20145A
DA97-05465A
DA97-05033D

6002-000213
DA63-03449A
DA97-02650G
DA63-03843A
DA47-00264A
DA97-05383C
DA63-40167A
DA63-03764A
DA63-03765A
DA97-05370A
DA61-03174A
DA67-01781A
DA64-02235A
DA97-04856B
DA31-00071C
DA32-00006R
DA62-01380A
DA63-03419A
DA61-03202A
DA63-03685B
DA97-01666Y
DA61-03167A
DA97-05371B
DA61-03176A
DA63-03762A
DA97-05297B
DA97-04847D

6002-000213
DA61-03164A
DA97-05296B
DA97-04837A

SSVVCC--CCOODDEE

RQ611
RD023

RW648

RI028
RI028

RW648

RI029
RI029

RW648

RI999
RI999
RI100

RW648

RH029

RW648

RH029

RS047

RI044

RI220
RI195
RI200
RI195
RI204
RI205

RI168

RI228

RF037

RI211
RI238
RI006
RI201
RI190
RI207
RI197

RQ266

RI189

RS047

RI196

RQ265

RI193

RREEMMAARRKKPPAARRTT NNAAMMEE

KNOB-HUMIDITY
LEVER-HUMIDITY
ROLLER-FRE
ASSY RAIL-VEG L
RAIL-VEG L
ROLLER-FRE
ASSY RAIL-VEG R
RAIL-VEG R
ROLLER-FRE
ASSY CASE-VEG REF
CASE-VEG REF
COVER-VEG FRONT
ROLLER-FRE
FIXER-ROLLER
ASSY CASE-VEG REF R
CASE VEG REF R
COVER VEG FRONT R
ROLLER FRE
FIXER ROLLER
ASSY-PARTITION VEG
ASSY-COVER WATER TANK
SCREW-TAPPING
COVER-TANK WATER
ASSY TANK WATER
COVER HEATER WATER TANK
HEATER WATER TANK
ASSY COVER-SLIDE PANTRY
GROMMET-COVER SLIDE
COVER-SLIDE PANTRY A
COVER-SLIDE PANTRY B
ASSY SHELF-PANTRY
REINF-SHELF PANTRY
SHELF-PANTRY
WINDOW SHELF PANTRY
ASSY COVER-MOTOR DAMPER
DAMPER MOTOR
SENSOR TEMP-PANTRY
INSULATION-MOTOR DC DAMPER
COVER-MOTOR DC DAMPER
GUIDE-FRENCH
COVER-WATER FILTER
ASSY CASE-FILTER
GUIDE-PANTRY
ASSY COVER-RAIL PANTRY L
SUPPORT-ROLLER PANTRY
COVER-RAIL PANTRY L
ASSY ROLLER B
ASSY CASE-PANTRY
SCREW-TAPPING
CASE-PANTRY
ASSY ROLLER A
ASSY RAIL-PANTRY L

SSPPEECC

QUEEN,ABS
AW,HIPS,COOL-WHITE
POM,D22
AW-PJT
AW,HIPS,COOL-WHITE
POM,D22
AW-PJT
AW,HIPS,COOL-WHITE
POM,D22
AW-PJT
AW,SAN,NTR
AW,HIPS,COOL-WHITE
POM,D22
PA

SAN,NTR
HIPS,COOL WHITE
POM
PA

AW-PJT
TH,+,1,M4,L12,ZPC(WHT),SWRCH18A
AW-PJT,PP,COOL-WHITE

PP(BJ-730)
3W,DC 12V,48.0Ω
AW-PJT BEST
T3.0,SILICON,NTR
AW,GPPS,NTR
AW,HIPS,COOL WHITE
AW-PJT
AW-PJT,SECC1,T1.2,COOL WHITE
HIPS,COOL WHITE
GPPS,NTR
AW-PJT
DC12V,600mA,BBC-PJT
PX-41C,502AT,AW-PJT
AW-PJT,FOAMPS,NTR
AW-PJT,PP,COOL WHITE
AW-PJT,POM,COOL-WHITE(SC02740R)
AW-PJT,HIPS,COOL-WHITE
AW-PJT
AW,PP,COOL-WHITE
AW-PJT(BEST,GE)
AW-PJT,NBR,NTR
AW,HIPS,COOL-WHITE
AW-PJT,Ni-Zn
AW-PJT,COOL WHITE,ROLLER(Ni-Zn)
TH,+,1,M4,L12,ZPC(WHT),SWRCH18A
AW,HIPS,COOL-WHITE
AW-PJT,Ni-Zn
AW-PJT

■■

Parts List of Refrigerator

92

EXPLODED VIEW& PARTS LIST

NNOO

26-5

27
27-1
27-2
27-3
27-4
27-5
27-6

28

29

30

31
31-1
31-2
31-3
31-4
31-5
31-6

32

33
33-1
33-2
33-3
33-4
33-5
33-6
33-7
33-8
33-9

33-10
33-11
33-12
33-13
33-14
33-15
33-16

34

35
35-1
35-2
35-3
35-4
35-5
35-6
35-7
35-8
35-9

35-10
35-11

36

37

QQUUAANN

TTIITTYY

1
1
1
1
1
1
1
1
1
1
1
1
6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

CCOODDEE--NNOO

DA97-04838A
DA97-05384C

6002-000630
DA41-00423C
DA64-02246C
DA61-03176A
DA63-03763A
DA97-05297B
DA61-03175A
DA29-00003B
DA97-05240A
DA97-05359A

6002-001397
DA01-00422A
DA01-00428A
DA67-01778A
DA67-01779A
DA91-02545A
DA61-03591A
DA97-05239A
DA63-03687A
DA62-01475A
DA63-03737A
DA63-03686A
DA62-01569A
DA61-03505A
DA66-00476A
DA61-03506A
DA66-00477A
DA63-03688A
DA66-00475A
DA67-01719A
DA65-00046A
DA63-03689A
DA61-20124D
DA66-00478A
DA97-05422A
DA97-05246A
DA61-03517A
DA31-00105E
DA74-40151G
DA63-90008A
DA66-90003A
DA61-60001A
DA61-01659B
DA71-00163A
DA96-00036N
DA32-00011U
DA63-02012B
DA63-03691A
DA34-00033B

SSVVCC--CCOODDEE

RI194
RI191

RS080

RO052

RI207
RI198

RQ266

RI206
RI070
RI038

RS080

RF035

RF104

RW710

RF034

RF039
RO088
RW111
RW358
RW700

RF047

RREEMMAARRKKPPAARRTT NNAAMMEE

ASSY RAIL-PANTRY R
ASSY COVER-RAIL PANTRY R
SCREW-TAPPING
PBA PANEL-PANTRY
INLAY-CONTROL PANEL
SUPPORT-ROLLER PANTRY
COVER-RAIL PANTRY R
ASSY ROLLER B
SUPPORT-PANTRY
FILTER WATER-ASSY
ASSY SHELF REF FOLD
ASSY SHELF QUICK SPACE
SCREW TAPPING
GLASS SHELF QUICK SPACE A
GLASS SHELF QUICK SPACE B
SHELF QUICK SPACE A
SHELF QUICK SPACE B
ASSY HANGER QUICK SPACE
ANGLE-SHELF REF SIDE L
ASSY-TRAY ICE BUCKET
COVER-ICE BUCKET A
INSULATION-COVER ICE BUCKET
GASKET-COVER ICE BUCKET
COVER-CRUSHER

INSULATION-COVER ICE BUCKET-SUB

GUIDE-CRUSHER
LEVER-ICE BUCKET B
SPRING ETC-COVER BUCKET
LEVER-ICE BUCKET C
COVER-ICE BUCKET B
LEVER-ICE BUCKET A
CAP-LEVER ICE BUCKET
CLAMPER CORE-HELIX
TRAY-ICE BUCKET
SPRING ETC-DISPENSER
LEVER-CUBE
ASSY ICE MAKER
ASSY-CASE AUGER MOTOR
CASE-AUGER MOTOR
MOTOR GEARED-AUGER
VALVE-SOLENOID
BUSH-SOLENOID
GEAR-SOLENOID
SLIDER-SOLENOID DISP
PLATE-DRIVE AUGER
FIXER-NUT
ASSY-WIRE HARNESS SUB(EM)
SENSOR TEMP
COVER-MOTOR AUGER SUB
COVER HARNESS ICE ROOM
SWITCH DOOR

SSPPEECC

AW-PJT
AW-PJT(BEST)
PH,+,2S,M3,L8,ZPC(WHT),SWRCH18A

AW BEST,PC
AW-PJT,NBR,NTR
AW,HIPS,COOL-WHITE
AW-PJT,Ni-Zn
AW,PP,COOL-WHITE
ATOP,86*86*167,NSF53

W361.5,L206.5,T3.2
W340,L207,T3.2
ABS(HG-0760)
ABS(HG-0760

AW-PJT,HIPS,T2.5,-,-,-,-,WHT,187*266*120
AW-PJT,EPS,40,182,261,WHT,-,-,­AW-PJT,SILICONE,1.0,-,730,GRAY,-,OD5.0
AW-PJT,HIPS,T3,-,-,-,-,WHT,140*140*55
AW-PJT,EPS,20,30,115,WHT,-,-,­AW-PJT,HIPS,T3,-,-,WHT,48*96*60
AW-PJT,ABS,13,40,67,-,WHT,­AW-PJT,STS304,?1.2,ID 9.6,OD12,-,-,25,-,-,­AW-PJT,ABS,13,40,115,-,WHT,­AW-PJT,HIPS,T2,-,-,-,-,WHT,181*266*40
AW-PJT,ABS,T2.0,-,-,-,WHT,15*50*11
AW-PJT,ABS,T1.0,-,-,WHT,?9.8*6

AW-PJT,POM,-,?80,L440,WHT,INSERT : CLAMPER CORE

AW-PJT,ABS,T2.5,-,-,-,WHT,138*165*410
AW-BEST-GE-OEM,STS304,0.9,9
AW-PJT,MSWR10,?4.5,-,L550,-,-,-

AW-PJT,HIPS(HR-1360),-,-,-,COOL-WHT(SC-02740R),-

ISG3240SSI,18RPM,127Kgf.cm,192:1,110~127V,2.3A,-,-,4OT,-,-

SR-S6586B,-,-,-,-,CUBE-SN1,110-127[V]42Ω

-,POM,-,-,-,SC-93438R,­POM,-,-,-,-,SC-93438R

-,POM,-,-,-,-,­NEXT-PJT,STS304,T2.5,-,-,-,­ZIPEL,STS420,T1,-,CLIP,STS420-J2
AW-PJT,W/H EJECT MOTOR
PX-41C,AW-PJT,-40~110?,5V,-,-,F-SENSOR,YEL,100MM
A-TOP,ABS≥≠ø¨ NTR,-,-,-,-,-,NTR,­HIPS(HR-1360)
SLIDE,250V/125V

■■

Parts List of Refrigerator

93

EXPLODED VIEW& PARTS LIST

5-3) Cabinet

13-3

13-2

14-2

15-1

15-2

14-3

14-4

14-6

14-5

27-1

27-2

27-3

14-1

14-5-4

14-5-1

14-5-2

14-5-6

14-5-5

14-5-7

14-5-3

13-1

1

3

3

36

6

6

8

9

10

9

10

7

11-2

11-1

11

13

14

17

18

16

15

18-3

18-1

18-2

19

20

22

21

23

24

25

35

27

26

30

31

29

32

33

34

12

4-2

4-4

4-1

4-3

4-5

4

5-3

5-1

5-4

5-2

5

5-5

2-2

2-3

2

28

2-1

37

37

94

EXPLODED VIEW& PARTS LIST

NNOO

1
1
1
1

2
2-1
2-2
2-3

2
2-1
2-2
2-3

2
2-1
2-2
2-3

3

3

3

4
4-1
4-2
4-3
4-4
4-5
4-6

4
4-1
4-2
4-3
4-4
4-5
4-6

4
4-1
4-2
4-3
4-4
4-5
4-6

5
5-1
5-2
5-3
5-4
5-5

5
5-1
5-2
5-3
5-4
5-5

QQUUAANN

TTIITTYY

1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

CCOODDEE--NNOO

DA90-03870A
DA90-03870B
DA90-03870C
DA90-03870D
DA97-05390A
DA34-00043B
DA61-04051A
DA64-02256A
DA97-05390B
DA34-00043B
DA61-03678A
DA64-02256B
DA97-05390C
DA34-00043B
DA61-03678A
DA64-02256C
DA67-01613A
DA67-01613B
DA67-01613C
DA97-04874D
DA60-00162A
DA61-03239A
DA61-03301A
DA97-04903A
DA63-03673A
DA61-03677A
DA97-04874E
DA60-00162A
DA61-03239A
DA61-03301A
DA97-04903B
DA63-03673A
DA61-03677A
DA97-04874F
DA60-00162A
DA61-03239A
DA61-03301A
DA97-04903C
DA63-03673A
DA61-03677A
DA97-04875A
DA60-00162A
DA61-03240A
DA61-03301A
DA97-04903A
DA63-03673A
DA97-04875B
DA60-00162A
DA61-03240A
DA61-03301A
DA97-04903B
DA63-03673A

SSVVCC--CCOODDEE

RO150
RO159
RO008

RO150
RO159
RO008

RO150
RO159
RO008
RO184
RO184
RO184
RO041
RO152
RO129

RE084
RO172
RO170

RO152
RO129

RE084
RO172
RO170

RO152
RO129

RE084
RO172
RO170

RO042
RO152
RO128

RE084
RO172
RO170
RO042
RO152
RO128

RE084
RO172
RO170

RREEMMAARRKKPPAARRTT NNAAMMEE

ASSY CABINET FORM
ASSY CABINET FORM
ASSY CABINET FORM
ASSY CABINET FORM
ASSY-TOP TABLE
SWITCH REED-ASS'Y
PLATE-TOP TABLE
TOP TABLE
ASSY-TOP TABLE
SWITCH REED-ASS'Y
PLATE-TOP TABLE
TOP TABLE
ASSY-TOP TABLE
SWITCH REED-ASS'Y
PLATE-TOP TABLE
TOP TABLE
CAP-TOP TABLE
CAP-TOP TABLE
CAP-TOP TABLE
ASSY HINGE UPP-L
FASTENER-RING
HINGE-UPP L
SPRING ETC-AUTO CLOSE
ASSY LEVER-AUTO CLOSE
GROMMET-LEVER
FIXER WATER PIPE HINGE
ASSY HINGE UPP-L
FASTENER-RING
HINGE-UPP L
SPRING ETC-AUTO CLOSE
ASSY LEVER-AUTO CLOSE
GROMMET-LEVER
FIXER WATER PIPE HINGE
ASSY HINGE UPP-L
FASTENER-RING
HINGE-UPP L
SPRING ETC-AUTO CLOSE
ASSY LEVER-AUTO CLOSE
GROMMET-LEVER
FIXER WATER PIPE HINGE
ASSY HINGE UPP-R
FASTENER-RING
HINGE-UPP R
SPRING ETC-AUTO CLOSE
ASSY LEVER-AUTO CLOSE
GROMMET-LEVER
ASSY HINGE UPP-R
FASTENER-RING
HINGE-UPP R
SPRING ETC-AUTO CLOSE
ASSY LEVER-AUTO CLOSE
GROMMET-LEVER

SSPPEECC

AW-PJT,BLACK
AW-PJT,REAL-STS
AW-PJT,SNOW-WHITE
AW-PJT,PLATINUM-STS
AW-PJT,ABS,I-BLACK(SC-00477R)
200VDC,1.5A,
AW-PJT,SBHG1,T0.3,65.5,107,-,AW-BESTÄ
AW-PJT,ABS(VH0815),I-BLACK(SC-00477R)
AW-PJT,ABS,Creamy STS(SC-07009R)
200VDC,1.5A,
AW-PJT,SBHG1,T0.3,
AW-PJT,ABS(VH0815),Creamy STS(SC-07009R)
AW-PJT,ABS,Snow-White(SC-97527R)
200VDC,1.5A,
AW-PJT,SBHG1,T0.3,
AW-PJT,ABS(VH0815),Snow-White(SC-97527R)
AW-PJT,ABS,I-BLACK(SC-00477R)
AW-PJT,ABS,Creamy STS(SC-07009R)
AW-PJT,ABS,Snow-White(SC-97527R)
AW-PJT,T2.9,BLACK
AW-PJT,STS304,ID5,T0.5,OD11,BLACK,
AW-PJT,SHP1,T2.9,
AW-PJT,STS604,1.4,9.2,12,24,
AW-PJT,POM,i-BLACK
AW-PJT,NBR,-,-,-,-,-,BLACK

AW-PJT,T2.9,Creamy-STS
AW-PJT,STS304,ID5,T0.5,OD11,BLACK,
AW-PJT,SHP1,T2.9,
AW-PJT,STS604,1.4,9.2,12,24,
AW-PJT,POM,Creamy-STS
AW-PJT,NBR,-,-,-,-,-,BLACK

AW-PJT,T2.9,Snow-White
AW-PJT,STS304,ID5,T0.5,OD11,BLACK,
AW-PJT,SHP1,T2.9,
AW-PJT,STS604,1.4,9.2,12,24,
AW-PJT,POM,Snow-White
AW-PJT,NBR,-,-,-,-,-,BLACK

AW-PJT,T2.9,i-BLACK
AW-PJT,STS304,ID5,T0.5,OD11,BLACK,
AW-PJT,SHP1,T2.9,
AW-PJT,STS604,1.4,9.2,12,24,
AW-PJT,POM,i-BLACK
AW-PJT,NBR,-,-,-,-,-,BLACK
AW-PJT,T2.9,Creamy-STS
AW-PJT,STS304,ID5,T0.5,OD11,BLACK,
AW-PJT,SHP1,T2.9,
AW-PJT,STS604,1.4,9.2,12,24,
AW-PJT,POM,Creamy-STS
AW-PJT,NBR,-,-,-,-,-,BLACK

■■

Parts List of Cabinet

95

EXPLODED VIEW& PARTS LIST

NNOO

5
5-1
5-2
5-3
5-4
5-5

6

7

8

9

10

11
11-1
11-2

12

12

12

13
13-1
13-2
13-3

14
14-1
14-2
14-3
14-4
14-5

14-5-1
14-5-2
14-5-3
14-5-4
14-5-5
14-5-6
14-5-7

14-6

15
15-1
15-2

16

17

18
18-1
18-2
18-3

19

20

21

22

23

24

25

26

QQUUAANN

TTIITTYY

1
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
1
1
2
2
1
1
2
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
2
1
1
1
1
2
1

CCOODDEE--NNOO

DA97-04875C
DA60-00162A
DA61-03240A
DA61-03301A
DA97-04903C
DA63-03673A
DA63-02905A
DA97-04876B
DA97-04877B
DA61-40115B
DA61-01920A
DA97-05016A
DA61-00805C
DA61-03217A
DA63-03434A
DA63-03434B
DA63-03434C
DA97-02064B
DA60-90146A
DA61-40126B
DA64-01170A
DA97-05043B

6009-001252
DA63-03450A
DA63-40128A
DA63-40171B
DA97-03145K

6003-000003
DA31-00146D
DA61-02349B
DA61-02355B
DA63-01146A
DA63-40167A
DA96-00042A
DA97-05093A
DA31-00010D
DA31-00015C
DA61-20128A
DA63-02017A

MK172DR2U/E08

DA97-02895C
DA96-00270C
DA96-00174C

2301-001837
DA63-40171B
DA63-40171D
DA62-01514A
DA61-02657A
DA97-04977A
DA61-02434A
DA97-04049A

DA39-20389L

SSVVCC--CCOODDEE

RO042
RO152
RO128
RE084
RO172
RO170
RO163
RO039
RO039
RH009
RH012

RO001
RO158
RO003
RO003
RO003
RO002
RH019
RH011
RO002
RH003
RQ747
RH003
RH022
RH033
RO132
RS080

RI089

RF033
RH039
RO138

RI087
RI133

RH031

RI085
RI085

RW716

RQ565
RH002
RO138
RH005
RH027
RO153
RH033
RH034
RH014
RO141

RT094
RO128

RZ110
RH032

RREEMMAARRKKPPAARRTT NNAAMMEE

ASSY HINGE UPP-R
FASTENER-RING
HINGE-UPP R
SPRING ETC-AUTO CLOSE
ASSY LEVER-AUTO CLOSE
GROMMET-LEVER
GROMMET HINGE-MID,R
ASSY HINGE MID-L
ASSY HINGE MID-R
CASTER-FRONT
CASTER-RIVET

ASSY-SUPPORT FOOT FRONT

FOOT-FRONT
SUPPORT-FOOT FRONT
COVER-LEG FRONT
COVER-LEG FRONT
COVER-LEG FRONT
ASSY CHASSIS-COMP
PIN-CASTER
CASTER-REAR
CHASSIS COMP
ASSY TRAY-DRAIN WATER
SCREW-SPECIAL
TRAY-DRAIN WATER
GROMMET-SUB COND
GROMMET-SUCT PIPE A

ASSY SUPPORT-CIRCUIT MOTOR

SCREW-TAPTITE
MOTOR BLDC
SUPPORT-CIRCUIT MOTOR
BRACKET-CIRCUIT MOTOR
GROMMET-MOTOR,REAR
GROMMET-COVER CHIL
ASSY-HARNESS MOTOR
ASSY PIPE-SPIRAL COND
FAN-ASS'Y
FAN-TURBO
SPRING ETC-FAN
GROMMET-COMP
COMPRESSOR
ASSY-COMP SUB
ASSY-RELAY PTC
ASSY-HARNESS COMP
C-FILM,LEAD
GROMMET-SUCT PIPE A
GROMMET-SUCT PIPE B
DRYER
CLIP-DRYER

ASSY PIPE CONNECT-SUCTION

FIXER-HOSE(VALVE)
ASSY CAP-DRAIN
WIRE HARNESS-EARTH

SSPPEECC

AW-PJT,T2.9,Snow-White
AW-PJT,STS304,ID5,T0.5,OD11,BLACK,
AW-PJT,SHP1,T2.9,
AW-PJT,STS604,1.4,9.2,12,24,
AW-PJT,POM,Snow-White
AW-PJT,NBR,-,-,-,-,-,BLACK
NEXT,POM,T2.0,WHITE,
AW-PJT,T4.5,Ni-Cr
AW-PJT,T4.5,Ni-Cr
SR-50,PP
(ZPC2),MSWR10,OD8.0,L54
AW-PJT
AW-PJT,PP
AW-PJT,SHP1,T4.0,BLACK
AW-PJT,PP,i-BLACK
AW-PJT,PP,Creamy-STS
AW-PJT,PP,Snow-White
AD,NEXT,SBHG1,T1.4,
MSWR10,OD6.0,L40,ZPC2,SR2894
REFALL,PP,PI 44,NTR,W22,
AD,SBHG1,T1.4,
AW-PJT,
PH,+,M4.0,L20(12),ZPC(WHT),SWRCH18A
AW-PJT,PP,NTR,
,NBR,DARKGRAY
,NBR,OD20,ID4,L20,BLK
NEXT,
BH,+,B,M4,L10,ZPC(BLK),SWRCH18A,
,1500,DC12V,250mA,2.5W,MOTORBLDC,
NEXT,ABS,NTR,
ABS,NEXT,-,-,-,NTR
A-TOP,NBR,-,-,-,ID6.5,OD42,BLK,BLDCÄ
T3.0,SILICON,NTR
ATOP UL(MOTOR),CFAN,350MM
AW-PJT,
,ET,ZIPEL,ASSY,UNIT,?150
,ET-PJT,ABS+GLASS FIBE,GR4010
,STS304,PI7.8,OD1.0,FD
QUEEN,EPDM,
115127V~60HZ,RSCR,FAN
AW-PJT,MK172D-R2U,
12SP16A435RF100,135/61?,10•ÿ
AW-PJT,AWG 18Ä
12000nF,5/10%,250V,Bulk,50x25x36
,NBR,OD20,ID4,L20,BLK
RAIL L19.5,NR,OD20,ID6,BLK
REF-ALL,C1220T,OD18.70,L114
AD,SECC1,T0.4,
aw,c1220 t
ET'05-PJT,PP,T2
EPEL,ASSY,L224.5,SOFTPVC
GREEN/YEL,UL 1015 AWG18,150mm

■■

Parts List of Cabinet

96

EXPLODED VIEW& PARTS LIST

NNOO

27
27-1
27-2
27-3

28

29

30

31

32

33

34

35

36

QQUUAANN

TTIITTYY

1
1
1
1
1
1
1
1
1
3
1
1
1

CCOODDEE--NNOO

DA97-05147A
DA63-02907A
DA27-00009B
DA39-10165E
DA97-05363B
DA97-01947D
DA97-05031B
DA41-00413C
DA41-00320A
DA61-02434A
DA63-00586B
DA62-00914B
DA62-20111B

SSVVCC--CCOODDEE

RH040

RH040
RQ408
RO005
RO119

RH001

RO007
RO052
RO128
RW303
RO089
RO087

RREEMMAARRKKPPAARRTT NNAAMMEE

ASSY-COVER NOISE FILTER
COVER-NOISE FILTER
COIL CHOKE-EMI FILTER
CBF-POWER CORD
ASSY-COVER PIPE WATER
ASSY COVER-COMP
ASSY-COVER PCB PANEL
PBA MAIN-BEST
PBA SMPS-NEXT
FIXER-HOSE
COVER-TUBE FILTER
VALVE-WATER FITTING
TUBE-FITTING

SSPPEECC

AW-PJT
NEXT,PP,NFPP
FA2107LB,QUEEN GE,5mH,+50%,30%,10A,38*50
ET-PJT,SVT-3,125V,15A,L=2300,BLACK,UL
AW-PJT
AD,SBHG1,T0.35,
AW-PJT,

NEXT,TOP,CEM1,148*100,POWER SUPPLY,85~170V,50~60Hz

ET05,PP,T2
A-TOP,W76,L83
12A-41,110~127V
POM,SRS6580Z,OD8.1

■■

Parts List of Cabinet

37 DA97-05362A ASSY-PIPE WATER AW-PJT(BEST)

1

97

EXPLODED VIEW& PARTS LIST

5-4) Disassembly of Freeze Door

10-2

7-2

7-4

7-1

7-3

10-1

10

8

7

2

2

1

3

5

4

6

6

9

98

EXPLODED VIEW& PARTS LIST

NNOO

1
1
1
1
2
3
3
4
5
6

7
7-1
7-2
7-3
7-4

7
7-1
7-2
7-3
7-4

7
7-1
7-2
7-3
7-4

7
7-1
7-2
7-3
7-4

8

9

10
10-1
10-2

QQUUAANN

TTIITTYY

1
1
1
1
2
1
1
1
1
2
1
2
1
1
1
1
2
1
1
1
1
2
1
1
1
1
2
1
1
1
1
1
1
1
1

CCOODDEE--NNOO

DA91-02462R
DA91-02462N
DA91-02462P
DA91-02462Q
DA61-02984A
DA97-05557A
DA97-05557B
DA61-03153B
DA61-03155B
DA61-02904B
DA97-04869G

6002-000215
DA64-02068A
DA67-01716A
DA67-01717A
DA97-04869E

6002-000215
DA64-02068D
DA67-01716B
DA67-01717B
DA97-04869H

6002-000215
DA64-02068C
DA67-01716C
DA67-01717C

DA97-04869J

6002-000215
DA64-02068B
DA67-01716D
DA67-01717D
DA61-03762A
DA61-03763A
DA97-04880A
DA63-03458A
DA63-03459A

SSVVCC--CCOODDEE

RD001
RD001
RD001
RD001

RO061

RD012
RD012
RD092
RD093
RD086

RS080

RO017

RS080

RO017

RS080

RO017

RS080

RO017

RI214
RI216

RD017
RD107

RREEMMAARRKKPPAARRTT NNAAMMEE

ASSY DOOR FOAM FRE
ASSY DOOR FOAM FRE
ASSY DOOR FOAM FRE
ASSY DOOR FOAM FRE
FIXER-HANDLE
ASSY-GASKET DOOR FRE
ASSY-GASKET DOOR FRE
HANGER-RAIL FRONT L
HANGER-RAIL FRONT R
SUPPORT DOOR POSITION IN
ASSY HANDLE-BAR FRE
SCREW-TAPPING
HANDLE-BAR FRE
CAP-HANDLE L FRE
CAP-HANDLE R FRE
ASSY HANDLE-BAR FRE
SCREW-TAPPING
HANDLE-BAR FRE
CAP-HANDLE L FRE
CAP-HANDLE R FRE
ASSY HANDLE-BAR FRE
SCREW-TAPPING
HANDLE-BAR FRE
CAP-HANDLE L FRE
CAP-HANDLE R FRE
ASSY HANDLE-BAR FRE
SCREW-TAPPING
HANDLE-BAR FRE
CAP-HANDLE L FRE
CAP-HANDLE R FRE
SUPPORT-GUARD FRE L
SUPPORT-GUARD FRE R
ASSY GUARD FRE
GUARD-FRE
GUARD-FRE FLIP

SSPPEECC

AW-PJT,Empire-Black,i-BLACK
AW-PJT,Versailles STS,Noble-STS
AW-PJT,Snow-White
AW-PJT,Platinum-STS,Noble-STS
ATOP 06,POM,NTR
AW-PJT,BLACK,TD-SEC
AW-PJT,GRAY,TD-SECT
AW,SECC1,T2.0,COOL-WHITE
AW-PJT,SECC1,T2.0,COOL-WHITE
AW-PJT,HIPS,NTR
AW-PJT,MATURE BLACK,SPRAYÄ
TH,+,1,M4.0,L16,ZPC(WHT),SWRCH18A
AW-PJT,AL(A6063),MATURE-BLACK
AW-PJT,ABS(HG0760H),i-BLACK
AW-PJT,ABS(HG0760H),i-BLACK
AW-PJT,Versailles-STS,Versailles-Silver
TH,+,1,M4.0,L16,ZPC(WHT),SWRCH18A
AW-PJT,AL(A6063),Versailles-STS,SANDING
AW-PJT,ABS(HG0760H),Versailles-Silver
AW-PJT,ABS(HG0760H),Versailles-Silver
AW-PJT,SNOW WHITE,SPRAYÄ
TH,+,1,M4.0,L16,ZPC(WHT),SWRCH18A
AW-PJT,AL(A6063),Snow-White
AW-PJT,ABS(HG0760H),Snow-White
AW-PJT,ABS(HG0760H),Snow-White
AW-PJT,NEW VERSAILLES SILVER,SANDINGÄ
TH,+,1,M4.0,L16,ZPC(WHT),SWRCH18A
AW-PJT,AL(A6063),Versailles-STS

AW-PJT,ABS,CREAMY-STS,STS-PLATINUM SPRAYÄ
AW-PJT,ABS,CREAMY-STS,STS-PLATINUM SPRAY
AW-PJT(BEST),HIPS(HG-1760SF),COOL-WHITE(SC-02740R)
AW-PJT(BEST),HIPS(HG-1760SF),COOL-WHITE(SC-02740R)

AW-PJT,COOL-WHT
AW-PJT,HIPS(HR1360),COOL-WHITE
AW-PJT,HIPS(HR1360),COOL-WHITE

■■

Parts List of Freezer Door