Samsung PS50B550, PS58B550 User Manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at
www.samsung.com/register
Model Serial No.
Plasma TV
user manual
English - 2
User Instructions
Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more
than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image
retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not
install and operate there.
Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper
part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be
prevented from touching the upper part of the product.
The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as
temperature or humidity. This is normal and not a defect of the unit.
Cell Defects
The PDP uses a panel consisting of 2,360,000 (HD-level) to 6,221,000 (FHD-level) pixels which require sophisticated technology
to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of
the product.
Avoid operating the TV at temperatures below 5°C(41°F)
A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left,
right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a
game console may cause similar effect to the screen. Damages caused by the above effect are not covered by
the Warranty.
Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
Warranty
Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty. -
Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures,
high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may
cause a serious damage to your set.
Digital TV (DVB-T) Notice
1. Functionalities related to Digital TV(DVB) are only available in countries/areas where DVB-T (MPEG2 and MPEG4 AVC)
digital terrestrial signals are broadcasted or where you have access to a compatible DVB-C(MPEG2 and MPEG4 AAC)
cable-TV service. Please check with your local dealer the possibility to receive DVB-T or DVB-C signal.
2. DVB-T is the DVB European consortium standard for the broadcast transmission of digital terrestrial television and DVB-C
is that for the broadcast transmission of digital TV over cable.
However, some differentiated features like EPG (Electric Program Guide), VOD (Video on Demand) and so on, are not
included in this specication. So, they cannot be supported at this moment.
3. Although this TV set meets the latest DVB-T and DVB-C standards[August,2008], the compatibility with future DVB-T digital
terrestrial and DVB-C digital cable broadcasts cannot be guaranteed.
4. Some cable-TV providers may charge an additional fee for such a service and you may be required to agree to terms and
conditions of their business.
5. Some Digital TV functions might be unavailable in some countries or regions and DVB-C might not work correctly with all
providers.
6. For more information, please contact your local Samsung customer care centre.
© 2009 Samsung Electronics Co., Ltd. All rights reserved.
N O T
Symbol Press Note One-Touch Button TOOLS
English - 3
Contents
Connecting and Preparing Your TV
Checking Parts ■ ..........................................................................4
Using the Stand-Base ■ ...............................................................4
Assembling the Cables ■ .............................................................. 4
Viewing the Control Panel ■ ......................................................... 5
Viewing the Connection Panel ■ ................................................... 6
Remote Control ■ ......................................................................... 7
Installing Batteries in the Remote Control ■ ................................. 8
Switching On and Off ■ ................................................................. 8
Placing Your Television in Standby Mode ■ .................................. 8
Viewing the Menus ■ ....................................................................9
Using the TOOLS Button ■ ........................................................... 9
Plug & Play Feature ■ ................................................................10
Channel Control
Storing Channels ■ ................................................................... 11
Managing Channels ■ ................................................................13
Picture Control
Changing the Picture Settings ■ ................................................. 15
Setting up the TV with your PC ■ ...............................................18
PC Display ■ ............................................................................... 19
Sound Control
Changing the Sound Setting ■ ...................................................20
Selecting the Sound Mode ■ ...................................................... 21
Function Description
Conguring the Setup Menu ■ .................................................... 22
Setting the Time ■ ......................................................................24
Source List / Edit Name ■ ........................................................... 25
Supported Program ■ .................................................................26
Media Play
Connecting a USB Device ■ ....................................................... 27
Using the Media Play Function ■ ................................................ 28
Using and Sorting Photo List ■ ................................................... 29
Viewing a Photo or Slide Show ■ ..............................................30
Using and Sorting the Music List ■ ............................................. 31
Playing a Music ■ ......................................................................32
Picture / Music Settings Using Media Play ■ .............................. 33
Using the Setup Menu ■ ............................................................. 33
About Anynet+
Connecting Anynet+ Devices ■ ..................................................34
Setting Up Anynet+ ■ .................................................................35
Scanning and Switching between Anynet+ Devices ■ ................ 35
Recording ■ ................................................................................36
Listening through a Receiver (Home theater) ■ .........................37
Troubleshooting for Anynet ■
+
..................................................37
Recommendations for Use
Teletext Feature ■ .......................................................................38
Wall Mount Kit Specications (VESA) ■ ..................................... 39
Preparing before installing Wall- Mount on the wall ■ ................40
How to assemble the Stand-Base (depending on the model) ■ . 40
Securing the TV to the Wall ■ ..................................................... 41
Securing the Installation Space ■ ............................................... 41
Troubleshooting ■ ....................................................................... 42
Specications ■ .......................................................................... 45
Software License ■ ..................................................................... 46
English - 4
Using the Stand-Base
Two or more people should carry the PDP. Never lay the PDP on the oor N
because of possible damage to the screen. Always keep the PDP upright.
The PDP can rotate 20 degrees in right and left directions.
N
-20° ~ 20°
Checking Parts
Owner’s Instructions Remote Control/
AAA Batteries (2ea)
Power Cord Cloth-Clean Holder-Ring (4ea)
(Refer to page 40)
Holder-Wire Cable
Screw (4ea)
(PS50B550 only)
Cover-Bottom
(PS50B550 only)
Cover-Bottom /
Screws (2ea)
(PS58B550 only)
Ferrite Core for
Power Cord
Ferrite Core fo
Headphone
Ferrite Core (Power Cord, Headphone) N
The ferrite core is used to shield the cable from interference. When connecting a cable,
open the ferrite core and clip it around the cable near the plug as shown in the gure.
Connecting and Preparing Your TV
Assembling the Cables
Enclose the cables in the Holder-Wire Cable so that the cables are not visible through the
transparent stand.
English - 5
Viewing the Control Panel
The product colour and shape may vary depending on the model. N
Front Panel buttons
Touch each button to
operate.
1
SOURCE
Toggles between all the available input sources
(TV, AV1, AV2, Component1, Component2, PC, HDMI1,
HDMI2/DVI, HDMI3, HDMI4, USB).
In the on-screen menu, use this button as you would use
N
the ENTERE button on the remote control.
2
MENU
Press to see an on-screen menu of your TV’s features.
3
+ VOL –
Press to increase or decrease the volume. In the on-screen
menu, use the + VOL – buttons as you would use the
◄ and ► buttons on the remote control.
4
< CH >
Press to change channels. In the on-screen menu, use the
< CH > buttons as you would use the ▲ and ▼ buttons on
the remote control.
5 POWER INDICATOR
Lights up when the power is on.
6
(
POWER)
Press to turn the TV on and off.
7
REMOTE CONTROL SENSOR
Aim the remote control towards this spot on the TV.
8
SPEAKERS
English - 6
Whenever you connect an audio or video system to your set, ensure that all elements are switched off. N
When connecting an external device, match the colour of the connection terminal to the cable. N
1 POWER IN
Connect the supplied power cord.
2 AV IN 1, 2 (AUDIO R/L / VIDEO)
Video and audio inputs for external devices, such as a
camcorder or VCR.
3 PC IN (AUDIO / PC)
Connect to the video and audio output jack on your PC.
4 COMPONENT IN 1, 2
Audio (AUDIO L/R) and video (Y/P
B/PR) inputs for Component.
5 HEADPHONES JACK
You can connect a set of headphones if you wish to watch a
television programme without disturbing the other people in
the room.
Prolonged use of headphones at a high volume may
N
damage your hearing.
6 DIGITAL AUDIO OUT (OPTICAL)
Connect to a Digital Audio Component.
7 SERVICE
Connector for service.
8 AUDIO OUT (AUDIO R/L)
Connect RCA audio signals from the TV to an external source,
such as Audio equipment.
9 ANT IN
75Ω Coaxial connector for Aerial/Cable Network.
0 HDMI IN 1, 2(DVI), 3, 4
No additional Audio connection is needed for an HDMI to HDMI connection.
When using an HDMI/DVI cable connection, you must use the HDMI IN 2 (DVI) jack.
What is HDMI?
N
High Definition Multimedia interface - allows the
transmission of high denition digital video data and
multiple channels of digital audio.
The HDMI/DVI terminal supports DVI connection to -
an extended device with the appropriate cable (not
supplied). The difference between HDMI and DVI is
that the HDMI device is smaller in size, has the HDCP
(High Bandwidth Digital Copy Protection) coding feature
installed, and supports multi - channel digital audio.
DVI AUDIO IN
DVI audio outputs for external devices.
! USB
Connect a USB mass storage device to view photo les and
play audio les.
Supported modes for HDMI/DVI and Component
480i 480p 576i 576p 720p 1080i 1080p
HDMI/DVI 50Hz X X X O O O O
HDMI/DVI 60Hz X O X X O O O
Component O O O O O O O
Viewing the Connection Panel
The product colour and shape may vary depending on the model.
N
TV Rear Panel
4 852
3
Cable Television
Network
or
9
0
or
1
6
7
2
!
English - 7
Remote Control
You can use the remote control up to a distance of about 23 feet from the TV.
The performance of the remote control may be affected by bright light.
N
1
POWER button
(turns the TV on and off)
2
Selects the TV mode directly.
3
Number buttons for direct channel
access
4
Use to Select on-screen menu items
5
Temporary sound switch-off
6
Volume increase
Volume decrease
7
Available source selection
8
Channel control button
9
Use to quickly select frequently used
functions.
0
Control the cursor in the menu
!
Use to see information on the current
broadcast
@
Use these buttons in the Channel list,
etc.
$
Sound mode selection
%
Use these buttons in the Channel list,
and Anynet+.
^
Previous channel
&
Next channel
Previous channel
*
Displays the main on-screen menu
(
Press to switch to your Favourite
channels.
)
Returns to the previous menu
a
Exit the on-screen menu
b
This function enables you to view and
play photo, music and movie les from
an external device. (Refer to pages 29
(Photo), 31 (Music))
c
Picture size selection
d
Digital subtitle display
e
Electronic Program Guide (EPG)
display
Teletext Functions
2
Exit from the teletext display
(depending on the model)
7
Teletext mode selection (LIST/FLOF)
8
Teletext store
9
Teletext size
!
Teletext reveal
@
Fastext topic selection
#
Teletext display/mix both
teletext information and the normal
broadcast
^
Teletext sub page
&
P :Teletext next page
P :Teletext previous page
*
Teletext index
)
Teletext hold
a
Teletext cancel
English - 8
Installing Batteries in the Remote Control
1. Lift the cover at the back of the remote control upward as shown in the gure.
2. Install two AAA size batteries.
Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram inside
N
the compartment.
3. Close the cover.
Remove the batteries and store them in a cool, dry place if you won’t be using the
N
remote control for a long time.
If the remote control doesn’t work, check the following N
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power outage or is the power cord unplugged?
5. Is there a special uorescent light or neon sign nearby?
Switching On and Off
The mains lead is attached to the rear of your set.
1. Plug the mains lead into an appropriate socket.
The standby indicator lights up on your set.
N
2. Press the POWERP button on your set.
Yo
N
u also can press the POWERP button or the TV button on the remote control to turn the TV on.
The programme that you were watching last is reselected automatically.
3. Press the numeric button (0~9) or channel up / down (< / >) button on the remote control or < CH > button on your set.
When
N
you switch the set on for the very rst time, you will be asked to choose language in which the menus are to be displayed.
4. To switch your set off, press the POWERP button again.
Placing Your Television in Standby Mode
Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to
interrupt viewing temporarily (during a meal, for example).
1. Press the POWER
P
button on the remote control.
T
N
he screen is turned off and a red standby indicator appears on your set.
2. To switch your set back on, simply press the POWER
P
, numeric buttons (0~9), TV button or channel up / down (< / >) button
again.
Do
N
not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to unplug
the set from the mains and aerial.
English - 9
Viewing the Menus
1. With the power on, press the MENU button. The main menu appears on the
screen. The menu’s left side has icons: Picture, Sound, Channel, Setup, Input,
Application, Support.
2. Press the ▲ or ▼ button to select one of the icons. Then press the ENTER
E
button
to access the icon’s sub-menu.
3. Press the EXIT button to exit.
The on-screen menus disappear from the screen after about one minute.
N
Using the TOOLS Button
You can use the TOOLS button to select your frequently used functions quickly and easily. The Tools menu changes depending on
which external input mode you are viewing.
1. Press the TOOLS button. The Tools menu will appear.
2. Press the ▲ or ▼ button to select a menu, then press the ENTER
E
button.
3. Press the ▲ / ▼ / ◄ / ► / ENTER
E
buttons to display, change, or use the selected
items. For a more detailed description of each function, refer to the corresponding
page.
Anynet+ (HDMI-CEC), see page 35
Picture Mode, see page 15 •
Sound Mode, see page 20 •
Sleep Timer, see page 24 •
SRS TS HD, see page 20 •
Energy Saving, see page 23 •
Add to Favourite (or Delete from Favourite), see page 13 •
Auto Adjus • tment, see page 18
Mode : Standard
Cell Light : 7
Contrast : 95
Brightness : 45
Sharpness : 50
Colour : 50
Tint (G/R) : G50/R50
Advanced Settings
Picture
Tools
Anynet+ (HDMI-CEC)
Picture Mode : Standard
Sound Mode : Custom
Sleep Timer : Off
SRS TS HD : Off
Energy Saving : Off
Add to Favourite
U
Move E En ter e Exit
English - 10
Plug & Play Feature
When the TV is initially powered on, basic settings proceed automatically and subsequently.
The Screen Saver is activated if there is no remote control key input for longer than 1 minute while Plug & Play is running.
N
The Screen Saver is activated if there is no operating signal for longer than 15 minutes. N
1. Press the POWER button on the remote control. The message Select 'Home Use'
when installing this TV in your home. is displayed.
2. Then press the ◄ or ► button to select Store Demo or Home Use, then the
ENTER
E
button.
We recommend setting the TV to
N Home Use mode for the best picture in your
home environment.
Store Demo
N mode is only intended for use in retail environments.
If the unit is accidentally set to
N Store Demo mode and you want to return to Home Use (Standard): Press the Volume button on
the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.
The factory default setting for the picture will be
N Standard. Standard mode is the recommended home viewing picture mode.
3. Press the ENTER
E
button. Select the appropriate country by pressing the ▲ or ▼ button. Press the ENTERE button to conrm
your choice.
4. Press the ▲ or ▼ button to select the Antenna source to memorize. Press the ENTER
E
button to select Start.
Digital & Analogue • : Digital and Analogue channels.
Digital • : Digital channels.
Analogue • : Analogue channels.
The
N
channel search will start and end automatically.
Pr
N
ess the ENTER
E
button at any time to interrupt the memorization process.
A
N
fter all the available channels are stored, the message Set the Clock Mode. is displayed.
5. Press the ENTER
E
button. Press the ▲ or ▼ button to select Auto, then Press the ENTERE button.
If
N
you select Manual, Set current date and time is displayed. (refer to page 24)
If
N
you have received a digital signal, the time will be set automatically. If not, see page 24 to set the clock.
6. Press the ▲ or ▼ button to highlight the time zone for your local area (and to move the highlight to the appropriate time zone on the
map of the Australia). Press the ENTER
E
button.
7. The brief instruction on How to get the best performance from your new HDTV is displayed. Press the ENTER
E
button.
You can change previous or next page by pressing the
N
◄ or ► button.
Th
N
is menu is available HD Connection Guide in the Support menu.
8. The message Enjoy your TV. is displayed. When you have nished, press the ENTER
E
button.
If you want to return to this feature...
1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup,
then press the ENTER
E
button.
2. Press the ENTER
E
button again to select Plug & Play.
3. Enter your 4 digit PIN number. The default PIN number of a new TV set is
‘0-0-0-0’.
If
N
you want to change PIN number, refer to 22 page.
The
N Plug & Play feature is only available in the TV mode.
Any previous settings and adjustments will remain including the picture mode.
N
All Channel settings will be lost.
For home viewing, ensure the picture mode is set to Standard.
Setup
Plug & Play
►
Time
Game Mode : Off
Child Lock : On
Change PIN
Parental Lock
Subtitle
Teletext Language : ----
Plug & Play
Select 'Home Use' when installing this TV in your
home.
Store Demo
L Move E Enter
Home Use
English - 11
Storing Channels
Country
❑
You can change the desired country.
The PIN number input screen appears. Enter your 4 digit PIN number.
N
The default PIN number of a new TV set is ‘0-0-0-0’. N
Auto Store
❑
Scans for all channels with active broadcast stations (and availability depends on your
country) and stores them in the TV's memory.
You can memorize the Antenna source.
Digital & Analogue • : Digital and Analogue channels.
Digital • : Digital channels.
Analogue • : Analogue channels.
If you want to stop
N Auto Store, press the ENTER
E
button.
The
N Stop Auto Store? message will be displayed.
Select
N Yes by pressing the ◄ or ► button, then press the ENTER
E
button.
If a channel is locked using the
N Child Lock function, the PIN input window appears.
Manual Store
❑
Scans for a channel manually and stores it in the TV’s memory.
Digital Channel (DTV)
Manual store for digital channels.
Channel • : Set the Channel number using the ▲, ▼ or number (0~9) buttons.
Frequency • : Set the frequency using the number buttons.
Bandwidth • : Set the bandwidth using the ▲, ▼ or number (0~9) buttons.
When it has nished, channels are updated in the channel list.
N
Analogue Channel
Manual store for analogue channel.
Programme • (Programme number to be assigned to a channel): Sets the programme number using the ▲, ▼ or number (0~9)
buttons.
Colour System → Auto / PAL / SECAM / NTSC4.43 • : Sets the colour system value using the ▲ or ▼ button.
Sound System • → BG / DK / I / L : Sets the sound system value using the ▲ or ▼ button.
Channel • (When you know the number of the channel to be stored): Press the ▲ or ▼ button to select C (Air channel) or
S (Cable channel). Press the ► button, then press the ▲, ▼ or number (0~9) buttons to select the required number.
You can also select the channel number directly by pressing the number (
N
0~9) buttons.
If there is abnormal sound or no sound, reselect the sound standard required.
N
Search • (When you do not know the channel numbers): Press the ▲ or ▼ button to start the search. The tuner scans the
frequency range until the rst channel or the channel that you selected is received on the screen.
Store • (When you store the channel and associated programme number): Set to OK by pressing the ENTER
E
button.
Channel mode
N
C - (Air channel mode): You can select a channel by entering the assigned number to each air broadcasting station in this
mode.
S - (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this mode.
Channel Control
Continued...
Channel
Country : Australia
►
Auto Store
Manual Store
Full Guide
Mini Guide
Default Guide : Full Guide
Channel List
English - 12
Full Guide / Mini Guide
❑
The EPG (Electronic Programme Guide) information is provided by the broadcasters. Programme entries may appear blank or out
of date as a result of the information broadcast on a given channel. The display will dynamically update as soon as new information
becomes available.
Full Guide :
Displays the programme information as time ordered One hour segments. One hours of programme information is
displayed which may be scrolled forwards or backwards in time.
Mini Guide :
The information of each programme is displayed by each line on the current channel Mini Guide screen from the
current programme onwards according to the programme starting time order.
Default Guide
❑
Mini Guide / Full Guide :
You can decide whether to display either the Mini Guide
or the Full Guide when the GUIDE button on the remote control is pressed.
You can also display the guide menu simply by pressing the
O GUIDE button.
Using the Full / Mini Guide
▲ / ▼ / ◄ / ►
,
(ENTER)
Select a programme by pressing the ▲/▼/◄/► button.
If the next progrmme is selected, it is scheduled with the clock icon displayed. If the ENTERE button is pressed
again, press the ▲/▼/◄/► button to select Cancel Schedules, the scheduling is canceled with the clock icon gone.
For details about scheduling programmes, refer to the section.
RED Toggle between the Mini Guide or Full Guide.
GREEN
Full Guide: Scroll backwards quickly (-24 hours).
Mini Guide:
Display previous page quickly.
YELLOW
Full Guide: Scroll forwards quickly (+24 hours).
Mini Guide:
Display next page quickly.
BLUE Exit the guide.
INFO
INFO button for the detailed information. Channel Number, Running Time, Status Bar, Parental Level, Video Quality
Information (HD/SD), Sound Modes, Subtitle or Teletext, languages of Subtitle or Teletext and brief summary of the
highlighted programme are included on the detailed information. “…” will be appeared if the summary is long.
Channel List
❑
For the detailed procedures on using the Channel List, refer to the descriptions on pages 13~14.
Channel Mode
❑
When the P (< / >) button is pressed, Channels will be switched within the selected channel list.
Added Ch. : Channels will be switched within the memorized channel list.
Favourite Ch.
: Channels will be switched within the favourite channel list.
Fine Tune ❑(only analogue channels)
If the reception is clear, you do not have to ne tune the channel, as this is done automatically during the search and store
operation. If the signal is weak or distorted, you may have to ne tune the channel manually.
Fine tuned channels that have been saved are marked with an asterisk
N * on the right-hand side of the channel number in the
channel banner.
If you do not store the ne-tuned channel in memory, adjustments are not saved.
N
To reset the ne-tuning, select N Reset by pressing the ▼ button and then press the ENTER
E
button.
Channel
Full Guide
Mini Guide
Default Guide : Full Guide
►
Channel List
Channel Mode : Added Ch.
Fine Tune
Full Guide
DTV Cable 900 f tn 2:10 Tue 1 Jun
Freshmen On Campus
2:00 - 2:30
No Detailed Information
Today 2:00 - 3:00 3:00 - 4:00
Mint Extra
Loaded
Fresh 40 with Dynamite MC
The Distillery
Smash Hits! Sunday
900 f tn
901 ITV Play
902 Kerrang!
903 Kiss
903 oneword
903 Smash Hits!
▼
Street Hypn..
Kisstory
No Information
No Information
No Information
Freshmen O..
Watch
Information
Page
Mini Guide +24 Hours Exit
◀◀ ▶▶
Mini Guide DTV Cable 900 f tn
Street Hypnosis
Booze Britain
2:00
2:30
5:00
▼
Freshmen On Campus
Watch
Information
Page
Full Guide Exit
◀◀ ▶▶
English - 13
Managing Channels
Using this menu, you can Add / Delete or set Favourite channels and use the programme
guide for digital broadcasts.
Select a channel in the
N All Channels, Added Channels, Favourites, or Programmed
screen by pressing the ▲ or ▼ buttons, and pressing the ENTERE button. Then you
can watch the selected channel.
All Channels • : Shows all currently available channels.
Added Channels • : Shows all added channels.
Favourites • : Shows all favourite channels.
Programmed • : Shows all current reserved programmes.
Using the Colour buttons with the Channel List
N
Red ( - Channel Type): Toggle between your TV, Radio, Data / Other and All.
Green ( - Zoom): Enlarges or shrinks a channel number.
Yellow ( - Select): Selects multiple channel lists.
T - TOOLS (Tools): Displays the Delete (or Add), Add to Favourite (or Delete from
Favourite), Lock (or Unlock), Timer Viewing, Edit Channel Name, Edit Channel
Number, Sort, Select All, (or Deselect All), or Auto Store menu.
(The Options menus may differ depending on the situation.)
Channel Status Display Icons
N
A
An Analogue channel.
c
A channel selected by pressing the yellow button.
♥
A channel set as a Favourite.
(
A programme currently being broadcast.
\
A locked channel.
)
A reserved programme
Channel List Tools Menu ❑ (in All Channels / Added Channels / Favourites)
Press the N TOOLS button to use the tools menu.
Option menu items may differ depending on the channel status.
N
Add / Delete
You can delete or add a channel to display the channels you want.
All deleted channels will be shown on
N All Channels menu.
A gray-coloured channel indicates the channel has been deleted.
N
The N Add menu only appears for deleted channels.
You can also delete a channel to the
N Added Channels or Favourite menu in the
same manner.
Add to Favourite / Delete from Favourite
You can set channels you watch frequently as favourites.
Press the T TOOLS button to display Tools menu.
You can also add the favourite channel by selecting Tools → Add to Favourite (or Delete from Favourite).
The “♥” symbol will be displayed and the channel will be set as a favourite.
N
All favourite channels will be shown on N Favourite menu.
To select the Favourite channels you have set up, press the
O FAV.CH button on the
remote control.
Lock / Unlock
You can lock a channel so that the channel cannot be selected and viewed. This
function is available only when the Child Lock is set to On. (see page 22)
The PIN number input screen appears. Enter your 4 digit PIN number.
N
The default PIN number of a new TV set is ‘0-0-0-0’. You can change the PIN, by selecting NChange PIN from the menu.
The “
N
\” symbol will be displayed and the channel will be locked.
Edit Channel Name (only analogue channel)
Channels can labeled so that their call letters appear whenever the channel is selected.
The names of digital broadcasting channels are automatically assigned and cannot be labeled. N
Continued...
Channel
Mini Guide
Default Guide : Full Guide
Channel List
Channel Mode : Added Ch.
Fine Tune
824 UKTV Gold
825 UKTV style
A
1 C --
A
2 C
--
A 3 ♥ C
--
A 4 C
--
A 5 C
--
A 6 C
--
A 7 C
--
A 8 C
--
Added Channels
Channel Type Zoom Select
Tools
824 UKTV Gold
825 UKTV style
A
1 C --
A
2 C
--
A 3 C
--
A 4 C
--
A 5 C
--
A 6 C
--
A 7 C
--
A 8 C
--
All Channels
Delete
Add to Favourite
Lock
Timer Viewing
Edit Channel Name
Sort
▼
All
Channel Type Zoom Select
Tools
All
English - 14
Edit Channel Number (only digital channel)
You can also edit the channel number by pressing the number buttons on the remote control.
Sort (only analogue channel)
This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after using
the auto store.
Timer Viewing
If you reserve a programme you want to watch, the channel is automatically switched to the reserved channel in the Channel List;
even when you are watching another channel. To reserve a programme set the current time rst. (See page 24)
Only memorized channels can be reserved.
N
You can set the channel, month, day, year, hour and minute directly by pressing the number buttons on the remote control.
N
Reserving a programme will be shown on NProgrammed menu.
Digital Programme Guide and Viewing Reservation
N
When a digital channel is selected, and you press the ► button, the Programme Guide for the channel appears.
You can reserve a programme according to the procedures described above.
Select All / Deselect All
Select All • : You can select all the channels in the channel list.
Deselect Al • l: You can deselect all the selected channels in the channel list.
You can perform the add / delete, add to Favourites / delete from Favourites, or lock / unlock function for multiple channels at
N
the same time. Select the required channels and press the yellow button to set all the selected channels at the same time.
The
N c mark appears to the left of the selected channels.
You can only select
N Deselect All when there is a selected channel.
Auto Store
For further details on setting up options, refer to page 11. N
If a channel is locked using the N Child Lock function, the PIN input window appears.
Channel List Tools Menu ❑(in Programmed)
You can view, modify or delete a reservation.
Press the
N TOOLS button to use the tools menu.
Change Info
Select to change a viewing reservation.
Cancel Schedules
Select to cancel a viewing reservation.
Information
Select to view a viewing reservation. (You can also change the reservation information.)
Select All / Deselect All
You can select (or deselect) all channels in the channel list.
Programmed
1 / 1 / 2009
13:59 5 TV1 Quincy, M.E
18:59 2 TV3 The Equalizer
20:59 2 TV3 McMillan & Wife
21:59 2 TV3 M.Spillane’s mike Hammer
Change Info
Cancel Schedules
Information
Select All
Zoom Select
Tools Information
All
English - 15
Changing the Picture Settings
Mode
❑
You can select the type of picture which best corresponds to your viewing requirements.
Dynamic • : Selects the picture for high-denition in a bright room.
Standard • : Selects the picture for the optimum display in a normal environment.
Eco • : Selects the picture for optimum and eye-comfortable display.
Movie • : Selects the picture for viewing movies in a dark room.
Press the TTOOLS button to display Tools menu.
You can also set the picture mode by selecting Tools → Picture Mode.
Cell Light / Contrast / Brightness / Sharpness / Colour / Tint (G/R)
❑
Your television has several setting options that allow you to control the picture quality.
Cell Light • : Adjusts the pixel brightness.
Contrast • : Adjusts the contrast level of the picture.
Brightness • : Adjusts the brightness level of the picture.
Sharpness • : Adjusts the edge denition of the picture.
Colour • : Adjusts Colour saturation of the picture.
Tint (G/R) • : Adjusts the Colour tint of the picture.
Select a picture mode to be adjusted rst. The adjusted values are saved for each picture mode.
N
When you make changes to N Cell Light, Contrast, Brightness, Sharpness, Colour, or Tint (G/R), the OSD will be adjusted
accordingly.
In Analogue TV, Ext., AV modes of the PAL system, you cannot use the Tint Function.
N
In N PC mode, you can only make changes to Cell Light, Contrast and Brightness.
Settings can be adjusted and stored for each external device you have connected to an input of the TV.
N
The energy consumed during use can be signicantly reduced if the level of brightness of the picture is reduced, and then this N
will reduce the overall running cost.
Advanced Setting
❑
You can adjust the detailed settings for your screen including the color and contrast.
Advanced Setting
N is available in Standard or Movie mode.
In
N PC mode, you can only make changes to Dynamic Contrast, Gamma and
White Balance from among the Advanced Setting items.
Black Tone → Off / Dark / Darker / Darkest
You can select the black level on the screen to adjust the screen depth.
Dynamic Contrast → Off / Low / Medium / High
You can adjust the screen contrast so that the optimal contrast is provided.
Gamma
You can adjust the primary colour Intensity.
Colour Space
Colour Space is a colour matrix composed of red, green and blue colours. Select your favourite colour space to experience the
most natural colour.
Auto • : Automatically sets the color range depending on the input video source.
Native • : Sets the color range wider than the that of the input video source.
Custom • : Adjusts the color range to suit your preference.
Customizing the Colour Space
N
Colour - → Red / Green / Blue / Yellow / Cyan / Magenta
Adjusts the Colour range to suit your preference. - Colour is available when Colour Space is set to Custom.
Red - / Green / Blue: In Colour, you can adjust the RGB values for the selected colour.
Reset - : Resets the colour space to the default values.
Picture Control
Continued...
Colour : 50
Tint (G/R) : G50/R50
Advanced Setting
►
Picture Options
Picture Reset
Picture
Mode : Standard
►
Cell Light : 7
Contrast : 95
Brightness : 45
Sharpness : 50
Colour : 50
Tint (G/R) : G50/R50
Advanced Settings
Picture
English - 16
White Balance
You can adjust the colour temperature for more natural picture colours.
R-Offset / G-Offset / B-Offset / R-Gain / G-Gain / B-Gain • : Changing the adjustment value will refresh the adjusted screen.
Reset • : The previously adjusted white balance will be reset to the factory defaults.
Flesh Tone
You can adjust the esh tone to be more or less red.
Changing the adjustment value will refresh the adjusted screen.
N
Edge Enhancement → Off / On
You can emphasize object boundaries in the picture.
xvYCC → Off / On
Setting the xvYCC mode to on increases detail and colour space when watching movies from an external device (i.e. DVD player).
xvYCC
N is available when the picture mode is set to Movie, and the external input is set to HDMI or Component mode.
This function may not be supported depending on your external device.
N
Picture Options
❑
You can customize the additional picture settings to suit your preference.
In
N PC mode, you can only make changes to the Colour Tone, Size and Screen
Burn Protection from among the items in Picture Options.
Colour Tone → Cool / Normal / Warm1 / Warm2 / Warm3
You can select the most comfortable colour tone to your eyes.
The adjusted values are stored according to the selected Picture mode.
N
Warm1 N , Warm2, or Warm3 is only activated when the picture mode is Movie.
Size
You can select the picture size which best corresponds to your viewing requirements.
16:9 • : Sets the picture to the 16:9 aspect ratio.
Wide Zoom • : Magnify the size of the picture more than 4:3.
Zoom • : Magnies the 16:9 wide picture (in the vertical direction) to t the screen size.
4:3 • : Sets the picture to the 4:3 aspect ration.
Screen Fit: • Use the function to see the full image without any cutoff when HDMI (720p/1080i/1080p) or Component
(1080i/1080p) signals are input.
The picture size options may vary depending on the input source.
N
The items available may differ depending on the selected mode.
N
In NPC Mode, only 16:9 and 4:3 mode can be adjusted.
Settings can be adjusted and stored for each external device you have connected to an input of the TV.
N
Temporary image retention may occur when viewing a static image on the set for more than two hours.
N
After selecting NWide Zoom mode: Press the ► button to select Position, then press the ENTER
E
button.
Press the ▲ or ▼ button to move the screen up / down. Then press the ENTER
E
button.
After selecting
N
Zoom mode: Press the ► button to select Position, then press the ENTER
E
button. Press the ▲ or ▼
button to move the picture up and down. Then press the ENTER
E
button. Press the ► button to select Size, then press
the ENTER
E
button. Press the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction. Then press the
ENTER
E
button.
After selecting
N
Screen Fit in HDMI (1080i / 1080p) or Component (1080i / 1080p) mode: Select Position by pressing
the ◄ or ►button. Use the ▲, ▼, ◄ or ► button to move the picture.
Reset
N
: Press the ◄ or ► button to select Reset, then press the ENTER
E
button. You can initialize the setting.
If you use the
N
Screen Fit function with HDMI 720p input, 1 line will be cut at the
top, bottom, left and right as in the overscan function.
You can select these options simply by pressing the
O
P.SIZE button on the remote
control.
Digital NR → Off / Low / Medium / High / Auto
If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static
and ghosting that may appear on the screen.
When the signal is weak, select one of the other options until the best picture is displayed.
N
Continued...
Tint (G/R) : G50/R50
Advanced Setting
Picture Options
►
Picture Reset
Picture
English - 17
HDMI Black Level → Normal / Low
You can directly select the black level on the screen to adjust the screen depth.
This function is active only when the external input connects to HDMI (RGB signals).
N
1080 Full HD Motion Demo → Off / On
Samsung' new generation PDP panels deliver stunning Full HD motion clarity when
viewing fast action sports, movies, and games.
This function is not available in
N PC, Game, or Media Play mode.
Film Mode
You can optimize the picture mode for watching movies.
Off • : Turn the lm mode function off.
Auto1 : •
Automatically adjusts the picture for the best quality when watching a lm.
Auto2 : •
Automatically optimizes the video text when watching a lm.
Film Mode
N is supported in TV, AV, COMPONENT(480i/1080i) and HDMI(480i/1080i).
Film Mode
N is not supported in DTV channel with resolution 576p/720p.
Blue Only Mode → Off / On
This function is for AV device measurement experts. This function displays the blue signal only by removing the red and green
signals from the video signal so as to provide a Blue Filter effect that is used to adjust the Color and Tint of video equipment such
as DVD players, Home Theaters, etc.
Blue Only Mode
N is available when the picture mode is set to Movie or Standard.
Screen Burn Protection
Congures the Screen Burn Protection Options to prevent and reduce pixel burn.
When an image remains in one position too long, it may cause a permanent burn on the screen.
Pixel Shift • : To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This
technology enables you to set picture movement up/down (Vertical) and side to side (Horizontal). The Time setting allows you to
program the time between movement of the picture in minutes.
Set
N
Pixel Shift to On by pressing the ▲ or ▼ button, then press the ENTERE button.
Select the required option by pressing the ▲ or ▼ button, then press the
N
ENTERE button.
Available options:
N
Horizontal, Vertical, Time.
Optimum condition for pixel shift
N
Item TV/Ext/AV/Component/HDMI/PC
Horizontal 0~4 2
Vertical 0~4 4
Time (minute) 1~4 min 2 min
The Pixel Shift value may differ depending on the monitor size (inches) and mode.
N
This function is not available in the NScreen Fit mode.
Scrolling • : This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern
Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image
on the screen for a long time.
Side Grey • : When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the white
balance on both extreme left and right sides.
Light - : When you set the screen ratio to 4:3, it brightens the left and right sides.
Dark - : When you set the screen ratio to 4:3, it darkens the left and right sides.
Picture Reset → Reset Picture Mode / Cancel ❑
Resets all picture settings to the default values.
Select a picture mode to be reset. The reset is performed for each picture mode.
N
Advanced Setting
Picture Options
Picture Reset
►
Picture
English - 18
Setting up the TV with your PC
Preset: Press the NSOURCE button to select PC mode.
Auto Adjustment ❑
Auto Adjustment allows the PC screen of set to self-adjust to the incoming PC video
signal. The values of ne, coarse and position are adjusted automatically.
This function does not work in DVI-HDMI mode.
N
Press the TTOOLS button to display Tools menu.
You can also set the adjustment by selecting Tools → Auto Adjustment.
Screen ❑
Coarse
Adjusts the frequency when vertical noise appears on the screen.
Fine
Adjusts the screen to be clearer.
PC Position
Adjust the PC’s screen positioning if it does not t the TV screen. Press the ▲ or ▼ button to adjusting the Vertical-Position. Press
the ◄ or ► button to adjust the Horizontal-Position.
Image Reset
You can replace all image settings with the factory default values.
Brightness : 45
Sharpness : 50
Auto Adjustment
►
Screen
Advanced Setting
Picture Options
Picture Reset
Picture
Loading...