SAMSUNG PS-42P7HR User Manual

PDP-TELEVISION (PLASMA

DISPLAY PANEL)

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

Picture In Picture (PIP)

Energy Saving

TELETEXT

SRS TruSurroundXT

Digital Natural Image engine

(Option)

User Instructions

◆ Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

◆ Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there.

◆ Heat on the top of the PDP TV

The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.

◆ The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.

◆ Cell Defects

The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.

◆ Avoid operating the TV at temperatures below 5°C(41°F)

◆ A still image displayed too long may cause permanent damage to the PDP Panel.

◆ Afterimage on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

◆ Warranty

- Warranty does not cover any damage caused by image retention.

- Burn-in is not covered by the warranty.

◆ Installation

Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.

Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.

Checking Parts

Warranty Card/

Owner’s

Instructions

Power Cord

➢

Remote Control/

AAA Batteries

Ferrite Core for

Power Cord (PS-42P7H)

Ferrite Core (Power Cord, Antenna Cable, Side AV)

The ferrite core is used to shield the cable from interference. When connecting a cable, open the ferrite core and clip it around the cable.

Registration Card/

Safety Guide Manual

Ferrite Core for

Power Cord/

Antenna Cable/

Side AV

(PS-50P7H)

Cloth-Clean

S-VIDEO Cable

PC Cable

English - 2

Sold Separately

HDMI Cable

Scart Cable PC Audio Cable HDMI/DVI Cable

Antenna Cable

Component Cables

(RCA)

Contents

ENERAL INFORMATION

◆ G

■ User Instructions ................................................................................................... 2

■ Checking Parts...................................................................................................... 2

■ Control Panel ........................................................................................................ 5

■ Connection Panel.................................................................................................. 6

■ Using the Stand-Base ........................................................................................... 8

■ Viewing the Remote Control (depending on the model)....................................... 8

■ Installing Batteries in the Remote Control ............................................................ 9

◆ OPERATION

■ Switching Your Television On and Off ................................................................... 9

■ Viewing the Menus................................................................................................ 10

■ Freezing the Current Picture................................................................................. 10

■ Plug & Play Feature .............................................................................................. 11

■ Viewing an External Signal Sources..................................................................... 12

■ Editing Device Names........................................................................................... 12

◆ CHANNEL CONTROL

■ Storing Channels Automatically ............................................................................ 13

■ Storing Channels Manually ................................................................................... 14

■ Adding / Locking Channels ................................................................................... 15

■ Sorting the Stored Channels................................................................................. 16

■ Assigning Names to Channels.............................................................................. 16

■ Fine Tuning Channel Reception............................................................................ 17

◆ PICTURE CONTROL

■ Changing the Picture Standard............................................................................. 18

■ Customizing the Picture Settings .......................................................................... 18

■ Selecting the Picture Size ..................................................................................... 19

■ Digital NR .............................................................................................................. 19

■ SMD ...................................................................................................................... 19

■ DNIe Demo ........................................................................................................... 19

■ Viewing the Picture in Picture (PIP)...................................................................... 20

OUND CONTROL

◆ S

■ Sound Features..................................................................................................... 21

UNCTION DESCRIPTION

◆ F

■ Time Features ....................................................................................................... 22

■ Language .............................................................................................................. 23

■ Blue Screen........................................................................................................... 23

■ Melody................................................................................................................... 23

■ Energy Saving....................................................................................................... 23

■ Using Game Mode ................................................................................................ 23

■ Screen Burn Protection......................................................................................... 24

■ Setting the Blue Eye ............................................................................................. 25

◆ PC DISPLAY

■ Setting up Your PC Software (Based on Windows XP)........................................ 25

■ Input Mode (PC).................................................................................................... 26

■ Setting the PC....................................................................................................... 27

continued...

English - 3

Contents

ISELINK

◆ W

■ Using the WISELINK Function................................................................................. 28

■ Using the WISELINK Mode..................................................................................... 29

■ Using the Photo (JPEG) List.................................................................................... 30

■ Copying Photo Files................................................................................................ 36

■ Deleting Photo Files................................................................................................ 37

■ Printing the Photo Image......................................................................................... 38

■ Using the Music (MP3) List...................................................................................... 39

■ Copying Music Files................................................................................................ 40

■ Deleting Music Files................................................................................................ 41

■ Using the Setup Menu ............................................................................................ 42

◆ APPENDIX

■ Teletext Feature (depending on the model) .......................................................... 44

■ How to Install the Wall Mount Bracket.................................................................. 46

■ Setting Up Your Remote Control........................................................................... 48

■ Troubleshooting..................................................................................................... 53

Symbols

☛

➢

Press Important Note

English - 4

Control Panel

The product colour and shape may vary depending on the model.

➢

Front (or Side) Panel

Speaker

SOURCE

Displays a menu of all of the available input sources (TV, Ext.1, Ext.2, AV, S-Video, Component, PC, HDMI1, and HDMI2).

Press to see the on-screen menu of your TV’s features.

Press to decrease or increase the volume. In the on-screen menu, use the you use the œ and √ buttons on the remote control.

buttons as

C/P.

Press to change channels. In the on-screen menu, use the C/P. buttons as you use the … and † buttons on the remote control.

(ENTER)

Press to confirm a selection.

(Power) button

Press to turn the TV on and off.

Power Indicator

- Power Off: Blue

- Power On: Off

Remote Control Sensor

Aim the remote control towards this spot on the TV.

English - 5

Connection Panel

The product colour and shape may vary depending on the model.

➢

Side Panel

Œ S-VIDEO or VIDEO / AUDIO L/R

- Video (S-Video or Video) and audio inputs for external devices, such as a camcorder or VCR.

´ headphones jack

- You can connect a set of headphones if you wish to watch a television programme without disturbing the other people in the room.

Prolonged use of headphones at a high volume

➢

may damage your hearing.

ˇ CF/MD/MAGICSTOR

Insert an CF/MD/MAGICSTOR memory card into the

(Refer to page 28)

slot.

¨ SD/SM/MMC/MS/MSPRO/XD

Insert an SD/SM/MMC/MS/MSPRO/XD memory card into the slot.

ˆ (USB Mass Storage Class)

Connect an USB mass storage device to view photo files (JPEG) and play audio files (MP3). (Refer to page 28)

Ø PictBridge

Connect a printer with PictBridge support (sold separately).

➢

(Refer to page 28)

(Refer to page 38)

Some printers supporting PictBridge may not be compatible with this TV.

continued...

English - 6

Connection Panel

The product colour and shape may vary depending on the model.

➢

Rear Panel

”

’

Cable Television

Network

∏

Whenever you connect an audio or video system to your set, ensure that all elements are switched off.

☛

When connecting an external device, match the colour of the connection terminal to the cable.

☛

Œ ANT IN VHF/UHF (75Ω)

- 75Ω Coaxial connector for Aerial/Cable Network.

´ Connecting external Audio Devices

- Connect RCA audio signals from the TV to an external source, such as Audio equipment.

ˇ COMPONENT IN

- Audio (AUDIO R/L) and video (P

¨ PC IN / AUDIO

- Connect to the video and audio output jack on your PC.

ˆ EXT 1, EXT 2

- Inputs or outputs for external devices, such as VCR, DVD, video game device or video disc players.

Input/Output Specification

Connector

EXT 1 EXT 2

Ø HDMI IN 2

- Connect to the HDMI jack of a device with HDMI output.

∏ HDMI 1/DVI IN

- Connect to the HDMI jack of a device with HDMI output. These inputs can also be used as a DVI connection with separate analog audio inputs. An optional HDMI/DVI cable will be necessary to make this connection. When using the

Input

Video

✔✔✔✔✔✔

R/PB

/Y) inputs for Component.

Output

Video + Audio (L/R)S-Video RGBAudio (L/R)

Only TV or DTV output is available.

✔

Output you can choose.

English - 7

optional HDMI/DVI adapter, the DVI analog audio inputs on your TV allow you to receive left and right audio from your DVI device. (Not compatible with PC)

- When connecting this product via HDMI or DVI to a Set Top Box, DVD Player or Games Console etc, make sure that it has been set to a compatible video output mode as shown in the table below. Failure to observe this may result in picture distortion, image breakup or no picture.

- Do not attempt to connect the HDMI/DVI connector to a PC or Laptop Graphics Card. (This will result in a blank screen being displayed)

DVI AUDIO IN L/R

- DVI audio outputs for external devices.

” POWER IN

- Connect the supplied power cord.

’ SERVICE

- Connector for service only.

Supported modes for HDMI/DVI and Component

➢

HDMI/DVI 50Hz HDMI/DVI 60Hz Component

480i

480p

X X O

576i

576p

O X O

720p

O O O

1080i

O O O

Using the Stand-Base

Two or more people should carry the PDP.

➢

Never lay the PDP on the floor because of possible damage to the screen. Always keep the PDP upright.

The PDP can rotate 20 degrees in right and

➢

left directions.

-20° ~ 20°

Viewing the Remote Control

ŒŒ

POWER button (turns the TV on and off)

´´

Number buttons for direct channel access

ˇˇ

One/Two-digit channel selection

¨¨

Channel control button (Refer to page 15)

ˆˆ

Selects the TV mode directly

ØØ

Volume increase Volume decrease

∏∏

Temporary sound switch-off

””

Displays the main on-screen menu

’’

Picture-In-Picture On/Off

˝˝

Picture effect selection (Refer to page 18)

ÔÔ

Sound effect selection (Refer to page 21)



Sound mode selection

ÒÒ

TruSurround XT mode button

ÚÚ

Remote control setup

ÆÆ

Selects a target device to be controlled by the Samsung remote control (TV, DVD, STB, CABLE, VCR)

ıı

Press to backlight the VOL, CH, MUTE and the active source button (TV, DVD, CABLE, STB, VCR) on the remote.

˜˜

Available source selection

¯¯

Previous channel

˘˘

Automatic Power-off

¿¿

This function enables you to view and play photo (JPEG) and audio files (MP3) from an external device. (Refer to page 30 (JPEG), 39 (MP3))

¸¸

VCR/DVD Function (Rewind, Stop, Play/Pause, Fast/Forward

˛˛

Next channel Previous channel

◊◊

Exit the on-screen menu

±±

Control the cursor in the menu

≠≠

Use to see information on the current broadcast

——

Fastext topic selection

÷÷

Picture size selection

®®

Picture freeze

∑∑

Selects the PC mode directly

µµ

Select the channel of sub picture (PIP)

¥¥

If your remote control is not functioning properly, take out the batteries and press the reset button for about 2~3 seconds. Re-insert the batteries and try using the remote control again.

Teletext Functions

(Refer to page 44)

ˆˆ

Exit from the teletext display (depending on the model)

””

Teletext index

’’

Teletext hold

ÔÔ

Teletext store

˜˜

Teletext mode selection (LIST/FLOF)

¯¯

Teletext sub page

˛˛

P:Teletext next page P:Teletext previous page

◊◊

Teletext cancel

≠≠

Teletext reveal

––

Teletext display/mix both teletext information and the normal broadcast

——

Fastext topic selection

(depending on the model)

The performance of the remote

➢

control may be affected by bright light.

This is a special remote control for

➢

the visually impaired persons, and has Braille points on the Power, Channel and Volume buttons.

English - 8

Installing Batteries in the Remote Control

1 Lift the cover at the back of the remote control upward as shown in the figure.

2 Install two AAA size batteries.

Make sure to match the “+” and “–” ends of the batteries with the diagram

➢

inside the compartment.

3 Close the cover as shown in the figure.

Remove the batteries and store them in a cool and dry place if you won’t be

➢

using the remote control for a long time. The remote control can be used up to about 23 feet from the TV. (Assuming typical TV usage, the batteries last for about one year.)

If the remote control doesn’t work! Check the following:

➢

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power cut, or is the power cord unplugged?

5. Is there a special fluorescent light or a neon sign nearby?

Switching Your Television On and Off

The main lead is attached to the rear of the television.

1 Plug the main lead into an appropriate socket.

The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.

➢

2 Press the (Power) button (On/Off) on the front of the television or press the POWER ()button on the remote

control to switch the television on. The programme that you were watching last is re-selected automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing Channels Automatically” on page 13 or “Storing Channels Manually” on page 14.

If the television is initially powered on, several basic customer settings proceed automatically.

➢

Refer to “Plug & Play Feature” on page 11.

3 To switch the television off, press the (Power) button (On/Off) on the front of the television or press the

POWER ()button on the remote control.

4 To switch the TV on, press the (Power) button (On/Off) on the front of the TV or press the POWER ()button

or number buttons on the remote control.

English - 9

Viewing the Menus

Source List : TV Edit Name WISELINK

Input

Move Enter Exit

1 Press the MENU ()button.

The main menu is displayed on the screen. Its left side has five icons: Input, Picture, Sound, Channel, and Setup.

2 Press the … or † button to select one of the icons.

Press the ENTER

3 Press the … or † button to move to items in the menu.

Press the ENTER

4 Press the …/†/œ/√ button to change the selected items.

Press the MENU ()button to return to the previous menu.

5 Press the EXIT ()button to exit from the menu.

Freezing the Current Picture

You can freeze the picture when watching a television programme simply by pressing the “STILL” button. To return to normal viewing, press it again.

This function will automatically cancel five minutes later.

➢

()

button to access the icon’s sub-menu.

()

button to enter items in the menu.

English - 10

Plug & Play Feature

When the television is initially powered on, several basic customer settings proceed automatically and subsequently. The following settings are available.

1 If the television is in standby mode, press the POWER () button

on the remote control. The message to start Plug & Play is displayed.

The Language menu will automatically appear after several seconds.

3 Select the appropriate language by pressing the

Press the

ENTER ()

button. The message to check the connected status

… or †

button.

of the antenna is displayed.

4 Make sure that the antenna is connected to the TV.

Press the

ENTER ()

5 Select your country or area by pressing the

Press the

ENTER ()

6 To start channel store, press the

button. The Country menu is displayed.

… or †

button.

button. The menu to select channels is displayed.

ENTER ()

button. The search will end automatically. The TV will begin memorizing all of the available channels. Press the

ENTER ()

button to set the clock.

7 Press the œ or √ button to select the hour or minute.

… or †

Set these by pressing the

You can enter the hours or minutes by using the numeric buttons on the

➢

remote control.

8 Press the

ENTER ()

button.

button to confirm your setting.

The message “Enjoy your viewing” is displayed.

Plug & Play

Start Plug & Play

Enter Exit

Plug & Play

Language

Move Enter Skip

Country

Move Enter Skip

Auto Store

English

Deutsch

Français

Italiano

Plug & Play

Check antenna input.

Enter Skip

Plug & Play

Belgium

France

Germany

Italy

Plug & Play

P1 C

Start

Enter Skip

Plug & Play

Clock Set --:

40 MHz

0 %

If you want to reset this feature …

1 Press the MENU () button to display the menu.

Press the … or † button to select Setup, then press the ENTER ()

button.

3 Press the

The message to start Plug & Play is displayed.

ENTER ()

button again to select Plug & Play.

English - 11

Enter Skip

Plug & Play

Clock Set 00 : 00

Move Adjust Enter Skip

Enjoy your viewing

Plug & Play Language : English Time

Game Mode : Off

Blue Screen : Off Melody : Off

Move Enter Return

Setup

Viewing an External Signal Sources

Source List : TV Edit Name WISELINK

Ext.1 : Ext.2 : AV : S-Video : Component : PC :

Input

Move Enter Return

Source List

----

Move Enter Return

You can switch between viewing signals from connected equipment, such as a VCR, DVD, Set-Top Box, and the TV source (broadcast or cable).

1 Press the MENU () button to display the menu.

Press the ENTER () button to select Source List.

3 Press the

4 Press the

ENTER ()

… or †

button to select the signal source, then press the

button.

Available signal sources: TV, Ext.1, Ext.2, AV, S-Video, Component, PC, HDMI1, and HDMI2

You can select these options simply by pressing the SOURCE button

➢

on the remote control.

You can enter TV or PC mode directly by using the TV or PC button on the

➢

remote control unit.

button again.

Editing Device Names

Source List : TV Edit Name WISELINK

Ext.1 :

Ext.2 : AV : S-Video : Component : PC : HDMI1 : HDMI2 :

Input

Move Enter Return

Edit Name

-----

----

-----

VCR

-----

DVD

-----

D-VHS

-----

Cable STB

-----

Move Enter Return

You can give a name to the external source.

1 Press the MENU () button to display the menu.

3 Press the … or † button to select Edit Name, then press the

4 Press the

5 Select the required device by pressing

6 Press the EXIT button to exit.

Press the ENTER () button.

ENTER () button.

press the

ENTER ()

button.

… or †

, then press the

ENTER ()

… or †

button to select the external source to be edited, then

button.

vailable device names: VCR, DVD, D-VHS, Cable STB, HD STB,

Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, DHR (DVD HDD Recorder), and PC.

English - 12

Storing Channels Automatically

You can scan for the frequency ranges available to you (availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However you can sort numbers manually and clear any channels you do not wish to watch.

1 Press the MENU () button to display the menu.

Press the … or † button to select Channel, then press the ENTER () button.

Press the ENTER () button again. The available countries are listed.

Select your country by pressing the … or † button, then press the

ENTER () button.

Press the … or † button to select Auto Store, then press the ENTER () button.

Press the ENTER () button again to start the search. The search will end automatically.

To stop the search before it has finished, press the MENU () or the

➢

ENTER ()

button.

Country : Belgium Auto Store Manual Store Channel Manager Sort Name Fine Tune

Move Enter Return

Auto Store

P1 C

Enter Return

Channel

Start

40 MHz

0 %

English - 13

Storing Channels Manually

You can store television channels, including those received via cable networks. When storing channels manually, you can choose:

◆ Whether or not to store each of the channels found.

◆ The programme number of each stored channel which you wish to identify.

◆ Programme (Programme number to be assigned to a channel)

Press the

➢

◆ Colour System: AUTO/PAL/SECAM/NTSC4.43

Press the

◆ Sound System: BG/DK/I/L

Press the

◆ Channel (When you know the number of the channel to be stored)

Press the Press the √ button, then press the

➢ ➢

◆ Search (When you do not know the channel numbers)

Press the

The tuner scans the frequency range until the first channel or the channel that you selected is received on the screen.

◆ Store (When you store the channel and associated programme number)

Set to OK by pressing the

Channel mode

☛

◆ P (Programme mode): When completing tuning, the broadcasting stations in your area have been assigned

◆ C (Air channel mode): You can select a channel by entering the assigned number to each air broadcasting

◆ S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel

Channel

Country : Belgium Auto Store Manual Store Channel Manager Sort Name Fine Tune

Move Enter Return

Manual Store

Programme : P 1 Colour System : AUTO Sound System : BG Channel : C 4 Search : 63 MHz Store : ?

Move Enter Return

… or †

button until you find the correct number.

1 Press the MENU () button to display the menu.

Press the … or † button to select Channel, then press the ENTER ()

button.

3 Press the

ENTER ()

4 Select the required option by pressing the

ENTER ()

5 When you are satisfied with your setting, press the

… or †

button to select Manual Store, then press the

button.

… or †

button.

button, then press the

ENTER ()

button.

6 Press the EXIT button to exit.

You can also select the channel number directly by pressing the numeric buttons (0~9).

… or †

button to select the required colour standard.

… or †

button to select the required sound standard.

… or †

button to select C (Air channel) or S (Cable channel).

… or †

button to select the required number.

You can also select the channel number directly by pressing the numeric buttons (0~9). If there is abnormal sound or no sound, re-select the sound standard required.

… or †

button to start the search.

ENTER ()

button.

to position numbers from P00 to P99. You can select a channel by entering the position number in this mode.

station in this mode.

in this mode.

English - 14

Adding / Locking Channels

Using the Channel Manager, you can conveniently lock or add channels.

1 Press the MENU () button to display the menu.

Press the … or † button to select Channel, then press the ENTER () button.

3 Press the

ENTER ()

◆ Adding channels

Using the Channel Manager, you can add channels.

4 Select the Channel Manager by pressing the

5 Move to the

be added, and press the

➢

◆ Locking channels

This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by muting out video and audio.

6 Press the

button.

7 Select On by pressing the

button.

8 Press the

ENTER ()

9 Move to the

be locked, and press the

➢

10 Press the EXIT button to exit.

… or †

button to select Channel Manager, then press the

button.

()

symbol next to the

()

field by pressing the

If you press the

ENTER ()

button again, the

ENTER ()

…/†/œ/

√ buttons, select a channel to

button to add the channel.

channel disappears and the channel is not added.

… or †

button to select Child Lock, then press the

… or †

buttons, then press the

… or †

buttons to select the Channel Manager, then press the

ENTER ()

button.

()

field by pressing the

If you press the

ENTER ()

…/†/œ/

√ buttons, select a channel to

button.

button again, the

()

symbol next to the

channel disappears and the channel lock is canceled.

A blue screen is displayed when Child Lock is activated.

ENTER ()

Country : Belgium Auto Store Manual Store Channel Manager Sort Name Fine Tune

Move Enter Return

Channel Manager

Channel Manager Child Lock : Off

Move Enter Return

Channel Manager

P1 C 4

Prog.

0 C 1C 4 2C 24 3C 2 4C 5 5C 80 6C 7 7C 36 8C 52 9C11

Add Lock

Move Enter Page Return

Channel

1 / 10

You can select these options simply by pressing the CH MGR button

➢

on the remote control.

English - 15

Sorting the Stored Channels

Channel

Country : Belgium Auto Store Manual Store Channel Manager Sort Name Fine Tune

Move Enter Return

Sort

Prog. Ch. Name

1C 4

2C 24 3C 2 4C 5

Move Enter Return

This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after using the auto store.

1 Press the MENU () button to display the menu.

Press the … or † button to select Channel, then press the ENTER () button.

Press the … or † button to select Sort, then press the ENTER () button.

4 Select the channel that you wish to move by pressing the

then press the

ENTER ()

5 Select the number of the programme to which the channel is to be moved

by pressing the Press the

… or †

ENTER ()

all other channels are shifted accordingly.

6 Repeat steps 4 to 5 until you have moved all the channels to the required

programme numbers.

7 Press the EXIT button to exit.

Assigning Names to Channels

Channel

Country : Belgium Auto Store Manual Store Channel Manager Sort Name Fine Tune

Move Enter Return

Name

Prog. Ch. Name

-- -----

1C 4

2C 24 3C 2 4C 5

Move Adjust Return

-----

Channel names will be assigned automatically when channel information is broadcast. These names can be changed, allowing you to assign new names.

1 Press the MENU () button to display the menu.

Press the … or † button to select Channel, then press the ENTER () button.

Press the … or † button to select Name, then press the ENTER () button.

Press the … or † button to select then press the ENTER () button.

Press the … or † button to select a letter (A~Z), a number (0~9), or a symbol. Move on to the previous or next letter by pressing the press the ENTER () button.

6 Repeat steps 4 to 5 for each channel to be assigned to a new name.

7 Press the EXIT button to exit.

… or †

button,

button.

button. The channel is moved to its new position and

the channel to be assigned to a new name,

œ or √

button

, then

English - 16

Fine Tuning Channel Reception

If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, you may have to fine tune the channel manually.

1 Press the MENU () button to display the menu.

Press the … or † button to select Channel, then press the ENTER ()

button.

3 Press the

button.

4 To obtain a sharp and clear picture and good sound quality, press the œ or √

button until you reach the optimal setting.

➢

5 Press the EXIT button to exit.

➢

… or †

button to select Fine Tune, then press the

Press the

ENTER ()

To reset the fine tuning to 0, select Reset by pressing the button. Press the

ENTER ()

button.

ENTER ()

button.

… or †

Fine Tune Store will change the colour of the Channel OSD (On Screen Display) from White to Red and add the “*” mark.

Country : Belgium Auto Store Manual Store Channel Manager Sort Name Fine Tune

Move Enter Return

Fine Tune

Reset

Adjust Save Return

Mono

Picture : Dynamic Sound : Custom SRS TSXT : Off

Channel

English - 17

+ 39 hidden pages