Samsung PS-42P7HD User manual

PDP-TELEVISION (PLASMA

DISPLAY PANEL)

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

Picture In Picture (PIP)

Energy Saving

TELETEXT

SRS TruSurroundXT

Digital Natural Image engine

Digital Terrestrial Receiver

(Option)

User Instructions

◆ Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

◆ Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there.

◆ Heat on the top of the PDP TV

The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.

◆ The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.

◆ Cell Defects

The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.

◆ Avoid operating the TV at temperatures below 5°C(41°F)

◆ A still image displayed too long may cause permanent damage to the PDP Panel.

◆ Afterimage on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

◆ Warranty

- Warranty does not cover any damage caused by image retention.

- Burn-in is not covered by the warranty.

◆ Installation

Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.

Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.

Checking Parts

Warranty Card/

Owner’s

Instructions

Power Cord

➢

Remote Control/

AAA Batteries

Ferrite Core for

Power Cord

(PS-42P7HD)

Ferrite Core (Power Cord, Antenna Cable, Side AV)

The ferrite core is used to shield the cable from interference. When connecting a cable, open the ferrite core and clip it around the cable.

Registration Card/

Safety Guide Manual

Ferrite Core for

Power Cord/

Antenna Cable/

(PS-50P7HD)

Side AV

Cloth-Clean

S-VIDEO Cable

PC Cable

English - 2

Sold Separately

HDMI Cable

Scart Cable PC Audio Cable HDMI/DVI Cable

Antenna Cable

Component Cables

(RCA)

Contents

ENERAL INFORMATION

◆ G

■ User Instructions ................................................................................................... 2

■ Checking Parts...................................................................................................... 2

■ Control Panel (depending on the model) .............................................................. 5

■ Connection Panel (depending on the model) ....................................................... 6

■ Using the Stand-Base ........................................................................................... 8

■ Viewing the Remote Control (depending on the model)....................................... 8

■ Installing Batteries in the Remote Control ............................................................ 9

◆ OPERATION

■ Switching Your Television On and Off ................................................................... 9

■ Viewing the Menus................................................................................................ 10

■ Freezing the Current Picture................................................................................. 10

■ Plug & Play Feature .............................................................................................. 11

■ Viewing an External Signal Source....................................................................... 12

■ Editing Device Names........................................................................................... 12

◆ CHANNEL CONTROL (ANALOG TV)

■ Storing Channels Automatically ............................................................................ 13

■ Storing Channels Manually ................................................................................... 14

■ Adding / Locking Channels ................................................................................... 15

■ Sorting the Stored Channels................................................................................. 16

■ Assigning Names to Channels.............................................................................. 16

■ Fine Tuning Channel Reception............................................................................ 17

■ LNA (Low Noise Amplifier) .................................................................................... 17

◆ PICTURE CONTROL

■ Changing the Picture Standard............................................................................. 18

■ Customizing the Picture Settings .......................................................................... 18

■ Selecting the Picture Size ..................................................................................... 19

■ Digital NR .............................................................................................................. 20

■ SMD ...................................................................................................................... 20

■ DNIe Demo ........................................................................................................... 20

■ Viewing the Picture in Picture (PIP)...................................................................... 21

◆ SOUND CONTROL

■ Sound Features..................................................................................................... 22

◆ FUNCTION DESCRIPTION

■ Time Features ....................................................................................................... 23

■ Language .............................................................................................................. 24

■ Blue Screen........................................................................................................... 24

■ Melody................................................................................................................... 24

■ Energy Saving....................................................................................................... 24

■ Using Game Mode ................................................................................................ 24

■ Screen Burn Protection......................................................................................... 25

■ Setting the Blue Eye ............................................................................................. 25

◆ PC DISPLAY

■ Setting up Your PC Software (Based on Windows XP)........................................ 26

■ Input Mode (PC).................................................................................................... 26

■ Setting the PC....................................................................................................... 27

continued...

English - 3

Contents

ISELINK

◆ W

■ Using the WISE LINK Function ........................................................................................ 28

■ Using the WISELINK Mode .............................................................................................. 29

■ Using the Photo (JPEG) List............................................................................................. 30

■ Copying Photo Files........................................................................................................... 36

■ Deleting Photo Files........................................................................................................... 37

■ Printing the Photo Image................................................................................................... 38

■ Using the Music (MP3) List ............................................................................................... 39

■ Copying Music Files........................................................................................................... 40

■ Deleting Music Files........................................................................................................... 41

■ Using the Setup Menu....................................................................................................... 42

◆ USING THE DTV FEATURE

■ Previewing the DTV Menu System .................................................................................. 44

■ Basic Functions.................................................................................................................. 45

1 .Display Screen...............................................................................................................45

2. Volume Control .............................................................................................................. 45

3. Select Soundtrack.......................................................................................................... 45

4. Select Videotrack........................................................................................................... 45

5. Service List..................................................................................................................... 45

6. Program Information...................................................................................................... 46

■ Operating the DTV Menu .................................................................................................. 46

Main Menu.......................................................................................................................... 46

1. Installation ...................................................................................................................... 46

1.1 Select Country ............................................................................................................. 47

1.2 Auto Scanning.............................................................................................................. 47

1.3 Manual Scanning......................................................................................................... 47

1.4 Reset to Factory Defaults ........................................................................................... 47

2. Channel Organising....................................................................................................... 48

2.1 Delete Frequency ........................................................................................................ 48

2.2 Delete Channel............................................................................................................ 48

2.3 Delete All Channels..................................................................................................... 48

2.4 Move & Edit Channel .................................................................................................. 48

3. Parental Lock ................................................................................................................. 49

3.1 Set Channel Lock ........................................................................................................ 49

3.2 Change PIN Code ....................................................................................................... 49

3.3 Set Modem Lock ......................................................................................................... 49

4. System Setup.................................................................................................................50

4.1 Language Selection..................................................................................................... 50

4.2 OSD Setting.................................................................................................................50

4.3 Time Setting ................................................................................................................. 50

4.4 System Information...................................................................................................... 50

4.5 Software Upgrade........................................................................................................ 50

4.6 MHP Application Control............................................................................................. 51

4.7 Modem Setup .............................................................................................................. 51

■ Installing the CI card ..........................................................................................................51

■ Freezing the Current Picture............................................................................................. 51

◆ APPENDIX

■ Teletext Feature (depending on the model) .......................................................... 52

■ How to Install the Wall Mount Bracket.................................................................. 53

■ Setting Up Your Remote Control........................................................................... 56

■ Troubleshooting..................................................................................................... 61

Symbols

☛

➢

Press Important Note

English - 4

Control Panel

The product colour and shape may vary depending on the model.

➢

(depending on the model)

Front (or Side) Panel

SOURCE

Displays a menu of all of the available input sources (TV, Ext.1, Ext.2, AV, S-Video, Component, PC, HDMI1, HDMI2, and DTV).

Press to see the on-screen menu of your TV’s features.

Press to decrease or increase the volume. In the on-screen menu, use the you use the œ and √ buttons on the remote control.

C/P.

Press to change channels. In the on-screen menu, use the C/P. buttons as you use the … and † buttons on the remote control.

buttons as

(ENTER)

Press to confirm a selection.

(Power) button

Press to turn the TV on and off.

Power Indicator

- Power Off: Blue

- Power On: Off

Remote Control Sensor

Aim the remote control towards this spot on the TV.

Speakers

Press the MENU button once in DTV mode, then the DTV menu is displayed.

➢

English - 5

Connection Panel

The product colour and shape may vary depending on the model.

➢

(depending on the model)

Side Panel

1 S-VIDEO or VIDEO / AUDIO L/R

-Video (S-Video or Video) and audio inputs for external devices, such as a camcorder or VCR.

2 headphones jack

-You can connect a set of headphones if you wish to watch a television programme without disturbing the other people in the room.

Prolonged use of headphones at a high volume may damage your hearing.

➢

CF/MAGICSTOR

Insert an

CF/MD/MAGICSTOR

SD/SM/MMC/MS/MSPRO/XD

Insert an

SD/SM/MMC/MS/MSPRO/XD

(

USB Mass Storage Class)

Connect an USB mass storage device to view photo files (JPEG) and play audio files (MP3). (Refer to page 28)

PictBridge

Connect a printer with PictBridge support (sold separately). (Refer to page 38)

Some printers supporting PictBridge may not be compatible with this TV.

➢

7 Smart Card

Smartcard slot and CI module.

memory card into the slot. (Refer to page 28)

continued...

English - 6

Connection Panel

The product colour and shape may vary depending on the model.

➢

Rear Panel

(depending on the model)

Whenever you connect an audio or video system to your set, ensure that all elements are switched off.

☛

When connecting an external device, match the colour of the connection terminal to the cable.

☛

1 Common Interface Slot

- Insert CI (Common Interface) card into the slot.

Connecting CI (Common Interface) CARD

- When not inserting “CI CARD” in some channels,

“Scrambled Signal” is displayed on the screen.

- The pairing information containing a telephone number,

CI CARD ID, Host ID, and other information will be displayed in about 2~3 minutes. If an error message is displayed, please contact your service provider.

- When the channel information configuration has finished,

the message “Updating Completed” is displayed, indicating that the channel list is now updated. ➢ You must obtain a CI CARD from a local cable service

provider. Remove the CI CARD by carefully pulling it out with your hands since dropping the CI CARD may cause damage to it.

2 ANT IN VHF/UHF (75Ω)

-75Ω Coaxial connector for Aerial/Cable Network.

3 Connecting external Audio Devices

- Connect RCA audio signals from the TV to an external source, such as Audio equipment.

4 DIGITAL AUDIO OUT (OPTICAL)

- Connect to a Digital Audio Component.

5 DTV SERVICE

- Connector for service only.

6 COMPONENT IN

-Video (Y/PB/PR) and audio (AUDIO L/R) inputs for Component.

7 PC IN / AUDIO

- Connect to the video and audio output jack on your PC.

8 HDMI IN 2

- Connect to the HDMI jack of a device with HDMI output.

9 EXT 1, EXT 2

- Inputs or outputs for external devices, such as VCR, DVD, video game device or video disc players.

0 Modem connection port

Cable Television

Network

Input/Output Specification

! HDMI 1/DVI IN

@ SERVICE

# POWER IN

➢ Supported modes for HDMI/DVI and Component

English - 7

Connector

EXT 1 EXT 2

- Connect to the HDMI jack of a device with HDMI output. These inputs can also be used as a DVI connection with separate analog audio inputs. An optional HDMI/DVI cable will be necessary to make this connection. When using the optional HDMI/DVI adapter, the DVI analog audio inputs on your TV allow you to receive left and right audio from your DVI device. (Not compatible with PC)

- When connecting this product via HDMI or DVI to a Set Top Box, DVD Player or Games Console etc, make sure that it has been set to a compatible video output mode as shown in the table below. Failure to observe this may result in picture distortion, image breakup or no picture.

- Do not attempt to connect the HDMI/DVI connector to a PC or Laptop Graphics Card. (This will result in a blank screen being displayed)

DVI AUDIO IN L/R

- DVI audio outputs for external devices.

Input

Video

✔✔✔✔✔✔

Please insert the card as shown

Only TV or DTV output is available.

✔

- Connector for service only.

- Connect the supplied power cord.

480i

480p HDMI/DVI 50Hz HDMI/DVI 60Hz Component

X X O

576i

Output

Video + Audio (L/R)S-Video RGBAudio (L/R)

Output you can choose.

576p

720p

O X O

1080i

Using the Stand-Base

Two or more people should carry the PDP.

➢

Never lay the PDP on the floor because of possible damage to the screen. Always keep the PDP upright.

The PDP can rotate 20 degrees in right and

➢

left directions.

-20° ~ 20°

Viewing the Remote Control

77 88

00 !! @@ ##

$$ %%

^^ &&

** ((

The performance of the remote

➢

control may be affected by bright light.

This is a special remote control for

➢

the visually impaired persons, and has Braille points.

))

(depending on the model)

POWER button (turns the TV on and off) Number buttons for direct channel access One/Two-digit channel selection Channel control button (Refer to pages 14~16) Selects the TV and DTV mode directly

Volume increase

Volume decrease Temporary sound switch-off Displays the main on-screen menu Electronic Program Guide (EPG) display Picture-In-Picture On/Off Sound mode selection Select the teletext mode Previous channel/This key is used in the MHP application and to change the previous channel. This key is also used to back to the previous page in D.MENU. Remote control setup Selects a target device to be controlled by the Samsung remote control (TV, DVD, STB, CABLE, VCR) Available source selection Press to backlight the VOL, CH, MUTE and the active source button (TV, DVD, CABLE, STB, VCR) on the remote. Previous channel DTV menu display This function enables you to view and play photo (JPEG) and audio files (MP3) from an external device. (Refer to page 30 (JPEG), 39 (MP3)) VCR/DVD Function (Rewind, Stop, Play/Pause, Fast/Forward)

English - 8

Next channel Previous channel

Exit the on-screen menu

Control the cursor in the menu

Use to see information on the current broadcast

Fastext topic selection

Toggle between the TV and Radio channel

Picture freeze

This button is the hard key for accessing MHP Application List

Select the soundtrack/ videotrack list for the current service

If your remote control is not functioning properly, take out the batteries and press the reset button for about 2~3 seconds. Re-insert the batteries and try using the remote control again.

Teletext Functions

(Refer to page 52)

Exit from the teletext display (depending on the model)

Teletext index

Teletext hold

Teletext size selection

Teletext mode selection (LIST/FLOF)

Teletext sub page

P:Teletext next page P:Teletext previous page

Teletext cancel

Teletext reveal

Teletext display/mix both Pressing TEXT/MIX selects Teletext, Double, or Mix mode in sequence.

Fastext topic selection

Teletext store

Installing Batteries in the Remote Control

1 Lift the cover at the back of the remote control upward as shown in the

figure.

2 Install two AAA size batteries.

Make sure to match the “+” and “–” ends of the batteries with the

➢

diagram inside the compartment.

3 Close the cover as shown in the figure.

Remove the batteries and store them in a cool and dry place if you

➢

won’t be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV. (Assuming typical TV usage, the batteries last for about one year.)

If the remote control doesn’t work! Check the following:

➢

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power cut, or is the power cord unplugged?

5. Is there a special fluorescent light or a neon sign nearby?

Switching Your Television On and Off

The main lead is attached to the rear of the television.

1 Plug the main lead into an appropriate socket.

The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.

➢

2 Press the (Power) button (On/Off) on the front of the television or press the POWER ()button on the remote

control to switch the television on. The programme that you were watching last is re-selected automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing Channels Automatically” on page 13 or “Storing Channels Manually” on page 14.

If the television is initially powered on, several basic customer settings proceed automatically.

➢

Refer to “Plug & Play Feature” on page 11.

3 To switch the television off, press the (Power) button (On/Off) on the front of the television or press the

POWER ()button on the remote control.

4 To switch the TV on, press the (Power) button (On/Off) on the front of the TV or press the POWER ()button

or number buttons on the remote control.

English - 9

Viewing the Menus

Source List : TV Edit Name WISELINK

Input

Move Enter Exit

1 Press the MENU ()button.

The main menu is displayed on the screen. Its left side has five icons: Input, Picture, Sound, Channel, and Setup.

2 Press the … or † button to select one of the icons.

Press the ENTER/OK ()button to access the icon’s sub-menu.

3 Press the … or † button to move to items in the menu.

Press the ENTER/OK ()button to enter items in the menu.

4 Press the …/†/œ/√ button to change the selected items.

Press the MENU ()button to return to the previous menu.

5 Press the EXIT () button to exit from the menu.

Freezing the Current Picture

You can freeze the picture when watching a television programme simply by pressing the STILL button. To return to normal viewing, press it again.

This function will automatically cancel five minutes later.

➢

English - 10

Plug & Play Feature

When the television is initially powered on, several basic customer settings proceed automatically and subsequently. The following settings are available.

1 If the television is in standby mode, press the POWER () button

on the remote control. The message to start Plug & Play is displayed.

The Language menu will automatically appear after several seconds.

3 Select the appropriate language by pressing the

… or †

button.

Press the ENTER/OK () button. The message to check the connected status of the antenna is displayed.

4 Make sure that the antenna is connected to the TV.

Press the ENTER/OK () button. The Country menu is displayed.

… or †

5 Select your country or area by pressing the

button.

Press the ENTER/OK () button. The menu to select channels is displayed.

6 To start channel store, press the ENTER/OK () button.

The search will end automatically. The TV will begin memorizing all of the available channels. Press the ENTER/OK () button to set the clock.

7 Press the œ or √ button to select the hour or minute.

… or †

Set these by pressing the

You can enter the hours or minutes by using the numeric buttons on the

➢

remote control.

button.

8 Press the ENTER/OK () button to confirm your setting.

The DTV channel scan menu appears and the DTV channel is automatically updated.

If the DTV channel is updated, the Source in the source list of the Input

➢

menu is automatically changed to DTV.

For detailed descriptions about DTV channel update, refer to page 48 of

➢

this manual.

Plug & Play

Start Plug & Play

Enter Exit

Plug & Play

Language

Move Enter Skip

Country

Move Enter Skip

Auto Store

P1 C

Clock Set --:

English

Deutsch Français

Italiano Svenska

Plug & Play

Check antenna input.

Enter Skip

Plug & Play

Belgium

France

Germany

Italy

Plug & Play

Start

Enter Skip

Plug & Play

40 MHz

0 %

If you want to reset this feature …

1 Press the MENU () button to display the menu.

Press the … or † button to select Setup, then press the button.

3 Press the ENTER/OK () button again to select Plug & Play.

The message to start Plug & Play is displayed.

ENTER/OK ()

English - 11

Enter Skip

Plug & Play

Clock Set 00 : 00

Move Adjust Enter Skip

Scanning for digital services...

Services found : 24 Channel : 38

Skip

Plug & Play Language : English Time

Game Mode : Off

Blue Screen : Off Melody : Off

Move Enter Return

Plug & Play

35%

Stop

Setup

Viewing an External Signal Sources

You can switch between viewing signals from connected equipment, such as a VCR, DVD, Set-Top Box, and the TV source (air or cable).

Source List : TV Edit Name WISELINK

Input

1 Press the MENU () button to display the menu.

Press the

ENTER/OK ()

button to select Source List.

3 Press the ENTER/OK () button again.

… or †

button to select the signal source, then press the

PC, HDMI1, HDMI2, and DTV

Ext.1 : Ext.2 : AV : S-Video : Component : PC :

Move Enter Return

Source List

----

Move Enter Return

4 Press the

ENTER/OK () button.

vailable signal sources:TV, Ext.1, Ext.2, AV, S-Video, Component,

You can select these options simply by pressing the SOURCE ()

➢

button on the remote control.

To watch television programme again, press the TV/DTV button and

➢

select the channel number required.

Editing Device Names

You can give a name to the external source.

Source List : TV Edit Name WISELINK

Input

1 Press the MENU () button to display the menu.

Press the

3 Press the … or † button to select Edit Name, then press the

ENTER/OK () button.

4 Press the

then press the ENTER/OK () button.

5 Select the required device by pressing

ENTER/OK () button.

vailable signal names: VCR, DVD, D-VHS, Cable STB, HD STB,

Ext.1 :

Ext.2 : AV : S-Video : Component : PC : HDMI1 : HDMI2 :

Move Enter Return

Edit Name

-----

----

-----

VCR

-----

DVD

-----

D-VHS

----

Cable STB

----

Move Enter Return

6 Press the EXIT button to exit.

ENTER/OK ()

… or †

button to select the external source to be edited,

button.

… or †

, then press the

Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, DHR (DVD HDD Recorder), and PC.

English - 12

Storing Channels Automatically

Not available in DTV or external input mode.

➢

You can scan for the frequency ranges available to you (availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However you can sort numbers manually and clear any channels you do not wish to watch.

1 Press the MENU () button to display the menu.

2 Press the … or † button to select Channel, then press the

ENTER/OK () button.

Press the

Select your country by pressing the … or † button, then press the

ENTER/OK ()

button again. The available countries are listed.

button.

5 Press the … or † button to select Auto Store, then press the

ENTER/OK () button.

Press the

ENTER/OK ()

button again to start the search. The search will

end automatically.

To stop the search before it has finished, press the MENU () or the

➢

ENTER/OK () button.

Channel

Country : Belgium Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA : Off

Move Enter Return

Auto Store

P1 C

Enter Return

Start

40 MHz

0 %

English - 13

Storing Channels Manually

Not available in DTV or external input mode.

➢

You can store television channels, including those received via cable networks. When storing channels manually, you can choose:

◆ Whether or not to store each of the channels found.

◆ The programme number of each stored channel which you wish to identify.

◆ Programme (Programme number to be assigned to a channel)

Press the

Channel

Country : Belgium Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA : Off

Move Enter Return

Manual Store

Programme : P 1 Colour System : AUTO Sound System : BG Channel : C 4 Search : 62 MHz Store : ?

Move Enter Return

… or †

button until you find the correct number.

◆ Colour System: AUTO/PAL/SECAM/NTSC4.43

Press the

… or †

button to select the required colour standard.

◆ Sound System: BG/DK/I/L Press the

… or †

button to select the required sound standard.

◆ Channel (When you know the number of the channel to be stored)

Press the

Press the √ button, then press the

➢ ➢

… or †

button to select C (Air channel) or S (Cable channel).

You can also select the channel number directly by pressing the numeric buttons (0~9). If there is abnormal sound or no sound, re-select the sound standard required.

◆ Search (When you do not know the channel numbers) Press the

The tuner scans the frequency range until the first channel or the channel that you selected is received

… or †

button to start the search.

on the screen.

◆ Store (When you store the channel and associated programme number) Set to OK by pressing the ENTER/OK ()button.

Channel mode

☛

◆ P (Programme mode): When completing tuning, the broadcasting stations in your area have been assigned

to position numbers from P00 to P99. You can select a channel by entering the position number in this mode.

◆ C (Air channel mode): You can select a channel by entering the assigned number to each air broadcasting

station in this mode.

◆ S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel

in this mode.

1 Press the MENU () button to display the menu.

2 Press the … or † button to select Channel, then press the ENTER/OK ()

button.

… or †

3 Press the

ENTER/OK ()button.

4 Select the required option by pressing the

ENTER/OK () button.

button to select Manual Store, then press the

… or †

button, then press the

5 When you are satisfied with your setting, press the ENTER/OK ()

button.

6 Press the EXIT button to exit.

… or †

button to select the required number.

English - 14

Adding / Locking Channels

Not available in DTV or external input mode.

➢

Using the Channel Manager, you can conveniently lock or add channels.

1 Press the MENU () button to display the menu.

Press the … or † button to select Channel, then press the ENTER/OK ()

button.

3 Press the

ENTER/OK () button.

◆ Adding channels

Using the Channel Manager, you can add channels.

4 Select the Channel Manager by pressing the ENTER/OK () button.

5 Move to the

be added, and press the ENTER/OK () button to add the channel.

➢

◆ Locking channels

This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by muting out video and audio.

4 Press the … or † button to select Child Lock, then press the ENTER/OK

() button.

5 Select On by pressing the … or † buttons, then press the ENTER/OK ()

button.

6 Press the … or † buttons to select the Channel Manager, then press the

ENTER/OK () button.

7 Move to the

be locked, and press the ENTER/OK () button.

➢

8 Press the EXIT button to exit.

… or †

button to select Channel Manager, then press the

field by pressing the

()

If you press the ENTER/OK () button again, the

…/†/œ/

√ buttons, select a channel to

()

symbol next

to the channel disappears and the channel is not added.

()

field by pressing the

If you press the ENTER/OK () button again, the

…/†/œ/

√ buttons, select a channel to

()

symbol next

to the channel disappears and the channel lock is canceled.

A blue screen is displayed when Child Lock is activated.

Country : Belgium Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA : Off

Move Enter Return

Channel Manager

Channel Manager Child Lock : Off

Move Enter Return

Channel Manager

P1 C 1

Prog.

0 C

1C 1 2C 3 3C 5 4C 8 5C 9 6C 10 7C 11 8C 12 9S 12

Add Lock

Move Enter

Page Exit

Channel

1 / 10

You can select these options simply by pressing the CH MGR button

➢

on the remote control.

English - 15

Sorting the Stored Channels

Not available in DTV or external input mode.

➢

This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after using the auto store.

Channel

Country : Belgium Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA : Off

Move Enter Return

Sort

Prog. Ch. Name

1C 4

2C 74 3C 75 4S 1

Move Enter Return

1 Press the MENU () button to display the menu.

Press the … or † button to select Channel, then press the ENTER/OK ()

button.

Press the … or † button to select Sort, then press the button.

4 Select the channel that you wish to move by pressing the

then press the ENTER/OK () button.

5 Select the number of the programme to which the channel is to be moved by

… or †

pressing the

button.

Press the ENTER/OK () button. The channel is moved to its new position and all other channels are shifted accordingly.

6 Repeat steps 4 to 5 until you have moved all the channels to the required

programme numbers.

7 Press the EXIT button to exit.

Assigning Names to Channels

Not available in DTV or external input mode.

➢

Channel names will be assigned automatically when channel information is broadcast. These names can be changed, allowing you to assign new names.

Channel

Country : Belgium Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA : Off

Move Enter Return

Name

Prog. Ch. Name

-- -----

1C 4

2C 74 3C 75 4S 1

Move Adjust Return

-----

1 Press the MENU () button to display the menu.

2 Press the … or † button to select Channel, then press the ENTER/OK

() button.

3 Press the … or † button to select Name, then press the ENTER/OK ()

button.

4 Press the … or † button to select the channel to be assigned to a new

name, then press the ENTER/OK () button.

5 Press the … or † button to select a letter (A~Z), a number (0~9), or a

symbol. Move on to the previous or next letter by pressing the œ or √ button, then press the ENTER/OK () button.

6 Repeat steps 4 to 5 for each channel to be assigned to a new name.

7 Press the EXIT button to exit.

ENTER/OK ()

… or †

button,

English - 16

Fine Tuning Channel Reception

Not available in DTV or external input mode.

➢

If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, you may have to fine tune the channel manually.

1 Press the MENU () button to display the menu.

Press the … or † button to select Channel, then press the

ENTER/OK ()

Press the … or † button to select Fine Tune, then press the

button.

ENTER/OK () button.

4 To obtain a sharp and clear picture and good sound quality, press the

œ or √ button until you reach the optimal setting. Press the

ENTER/OK ()

To reset the fine tuning to 0, select Reset by pressing the

➢

button. Press the ENTER/OK () button.

button.

… or †

5 Press the EXIT button to exit.

Fine Tune Store will change the colour of the Channel OSD (On Screen

➢

Display) from White to Red and add the “*” mark.

P1 Mono

Channel

Country : Belgium Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA : Off

Move Enter Return

Fine Tune

Reset

Adjust Save Return

LNA (Low Noise Amplifier)

This function is very useful in the situation that the TV is used in weak signal. LNA amplifies the TV signal in the weak signal area, a low-noise preamplifier boosts the incoming signal.

1 Press the MENU () button to display the menu.

Press the … or † button to select Channel, then press the ENTER/OK ()

button.

3 Press the

… or †

button to select LNA, then press the ENTER/OK ()

button.

4 Select Off or On by pressing the … or † button, then press the ENTER/OK

() button.

5 Press the EXIT button to exit.

Depending on areas, factory mode of LNA, will be set up as On or Off.

➢

Channel

Country : Belgium Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA : Off

Move Enter Return

English - 17

Changing the Picture Standard

You can select the type of picture which best corresponds to your viewing requirements.

Mode : Dynamic Size : Auto Wide Digital NR : On SMD : On DNIe Demo : Off PIP

Mode : Dynamic

Contrast 100 Brightness 50 Sharpness 75 Colour 55

Tint G 50 R 50

Colour Tone : Cool1 Reset

Picture

Move Enter Return

Mode

Dynamic

Standard

Movie

Custom

Move Enter Return

1 Press the MENU () button to display the menu.

Press the … or † button to select Picture, then press the button.

3 Press the ENTER/OK () button twice.

4 Select the required mode by pressing the … or † button, then press the

ENTER/OK () button.

Available modes: Dynamic, Standard, Movie, and Custom

The setting values may vary depending on the input source.

➢

(ex. RF, Video, Component, PC, or HDMI)

5 Press the EXIT button to exit.

◆ Choose Dynamic for viewing the TV during the day or when there is

➢

bright light in the room.

◆ Choose Standard for the standard factory settings.

◆ Choose Movie when viewing the movie.

◆ Choose Custom if you want to adjust the settings according to personal

preference.

Customizing the Picture Settings

Your television has several setting options that allow you to control the picture quality.

Mode : Dynamic Size : Auto Wide Digital NR : On SMD : On DNIe Demo : Off PIP

Mode : Dynamic Contrast 100 Brightness 50 Sharpness 75 Colour 55

Tint G 50 R 50

Colour Tone : Cool1

Reset

Picture

Move Enter Return

Mode

Cool2

Cool1

Normal Warm1 Warm2

Move Enter Return

1 Press the MENU () button to display the menu.

Press the … or † button to select Picture, then press the ENTER/OK ()

button.

3 Press the ENTER/OK () button twice.

4 Select the required mode by pressing the … or † button, then press the

ENTER/OK () button.

vailable modes: Dynamic, Standard, Movie, and Custom

5 Select the required option by pressing the … or † button, then press the

ENTER/OK () button.

6 When you are satisfied with your setting, press the ENTER/OK () button.

7 Press the EXIT button to exit.

◆ Contrast – Brightness – Sharpness – Colour – Tint (NTSC only)

◆ Contrast – Brightness – Colour : PC Mode

Press the œ or √ button until you reach the optimal setting.

◆ Colour Tone: Cool2/Cool1/Normal/Warm1/Warm2

◆ Reset: You can return to the factory defaults picture settings.

The reset function is set for each picture mode and colour tone.

➢

ENTER/OK ()

English - 18

Selecting the Picture Size

You can select the picture size which best corresponds to your viewing requirements.

1 Press the MENU () button to display the menu.

Press the … or † button to select Picture, then press the

ENTER/OK () button.

3 Press the … or † button to select Size, then press the ENTER/OK ()

Mode : Dynamic Size : Auto Wide Digital NR : On SMD : On DNIe Demo : Off PIP

button.

4 Select the required option by pressing the … or † button, then press the

ENTER/OK () button.

vailable options: Auto Wide, 16:9, Wide 4:3, Zoom, 4:3

◆ Auto Wide

: Expanding and pulling up the picture from 4:3 to 16:9

ratio.

Auto Wide 16:9 Wide 4:3 Zoom 4:3

◆ 16:9:Sets the picture to 16:9 wide mode.

◆ Wide 4:3

Magnify the size of the picture more than

4:3

Move the screen up/down using the … or † button after selecting the by pressing the √ or ENTER/OK () button.

Magnify the size of the picture vertically on screen.

◆ Zoom

◆ 4:3:Sets the picture to 4:3 normal mode.

5 Press the EXIT button to exit.

If you change the picture size when PIP is On, PIP will automatically be

➢

turned Off. Depending on the input source, the picture size options may vary.

➢

The items available may differ depending on the selected mode.

➢

Positioning and Sizing the screen using Zoom

◆ Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down direction

using the … or † button as well as the screen size.

◆ Move the screen up/down using the … or † button after selecting the by pressing the œ or √ button.

◆ Resize the screen vertically using the … or † button after selecting the by pressing the œ or √ button.

Picture

Move Enter Return

Size

Move Enter Return

English - 19

Digital NR / SMD / DNIe Demo

Mode : Dynamic Size : Auto Wide Digital NR : On SMD : On DNIe Demo : Off PIP

◆ Digital NR:On/Off

If the signal received by the television is weak, you can activate this feature to reduce any static and ghosting that may appear on the screen.

◆ SMD(Smooth Motion Driver)

If you set SMD to On, you can view more natural skin and clear text even in fast moving scenes.

➢

◆ DNIe Demo

This TV includes the DNIe function so as to provide a high visual quality. If you set DNIe Demo to On, you can view an applied DNIe and a normal picture on the screen, for demonstration purposes. Using this function, you can view the difference in the visual quality.

➢

Picture

Move Enter Return

1 Press the MENU () button to display the menu.

Press the … or † button to select Picture, then press the ENTER/OK () button.

3 Select the required option by pressing the

ENTER/OK () button.

vailable options: Mode, Size, Digital NR, SMD, DNIe Demo, PIP

… or †

button, then press the

4 When you are satisfied with your setting, press the ENTER/OK () button.

5 Press the EXIT button to exit.

On/Off

SMD is not available in PC mode.

On/Off

DNIeTM(Digital Natural Image engine)

This feature brings you more detailed image with 3D noise reduction, detail enhancement, contrast enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer, more detailed image to you. DNIeTMtechnology will fit every signal into your eyes.

DNIe Demo is not available in PC mode.

English - 20

+ 45 hidden pages