Page 1
PDP-TELEVISION
(PLASMA DISPLAY PANEL)
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
Picture In Picture (PIP)
Colour Weakness Enhancement Mode
My Colour Control
TELETEXT
(Option)
SRS TruSurroundXT
Digital Natural Image engine
This device is a Class B digital apparatus.
Register your product at www.samsung.com/global/register
Page 2
User Instructions
◆ Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of the screen when displaying a still image.
◆ Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height so do not install and operate there.
◆ Heat on the top of the PDP TV
The top side of the product may be hot after long periods of use as heat dissipates from the panel
through the vent hole in the upper part of the product.
This is normal and does not indicate any defect or operation failure of the product.
However, children should be prevented from touching the upper part of the product.
◆ The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of
surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.
◆ Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require
sophisticated technology to produce. However, there may be few bright or dark pixels on the screen.
These pixels will have no impact on the performance of the product.
◆ Avoid operating the TV at temperatures below 5°C(41°F)
◆ A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave
traces of borders displayed on the left, right and centre of the screen caused
by the difference of light emission on the screen.
Playing a DVD or a game console may cause similar effect to the screen.
Damages caused by the above effect are not covered by the Warranty.
◆ Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may
produce partial afterimages.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
◆ Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
◆ Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy
dust, high or low temperatures, high humidity, chemical substance and where it operates continually
such as the airport, the train station etc.
Failure to do so may cause a serious damage to your set.
English - 2
Page 3
Checking Parts
Sold Separately
Owner’s Instructions
Power Cord
Remote Control/
AAA Batteries
S-VIDEO Cable
Component Cables
(RCA)
Scart Cable PC Audio Cable
Antenna Cable
PC Cable
English - 3
Page 4
Contents
◆ FOREWORD
■ User Instructions............................................................................................ 2
◆ CONNECTING AND PREPARING YOUR DISPLAY
■ Control Panel................................................................................................. 6
■ Infrared Remote Control ................................................................................ 8
■ Inserting the Batteries in the Remote Control................................................ 9
■ Assembling the Stand-Base .......................................................................... 9
■ Installing the Display on the Wall Attachment Panel ..................................... 10
■ Connecting to an Aerial or Cable Television Network ................................... 12
■ Connecting a Satellite Receiver or Decoder.................................................. 12
■ Switching Your Television On and Off........................................................... 13
■ Familiarizing Yourself with the Remote Control............................................. 14
■ Plug & Play Feature....................................................................................... 15
■ Choosing Your Language.............................................................................. 16
◆ SETTING THE CHANNELS
■ Storing Channels Automatically..................................................................... 17
■ Storing Channels Manually............................................................................ 18
■ Skipping Unwanted Channels ....................................................................... 20
■ Sorting the Stored Channels ......................................................................... 21
■ Assigning Names to Channels ...................................................................... 22
■ Locking the Channel...................................................................................... 23
■ Using the LNA (Low Noise Amplifier) Feature............................................... 24
■ Fine Tuning Channel Reception.................................................................... 25
◆ USING YOUR DISPLAY
■ Displaying Information ................................................................................... 26
■ Changing the Picture Standard ..................................................................... 26
■ Customizing the Picture Settings................................................................... 27
■ Setting the Picture (PC Mode)....................................................................... 28
■ Selecting the Picture Size.............................................................................. 30
■ Viewing the DNIe Demonstration .................................................................. 31
■ Freezing the Current Picture ......................................................................... 31
■ Setting the My Colour Control (Easy Control) ............................................... 32
■ Setting the My Colour Control (Detail Control) .............................................. 33
■ Setting the Blue Screen................................................................................. 34
■ Using the Colour Weakness Enhancement Feature ..................................... 35
■ Using the Energy Saving Feature.................................................................. 36
■ Viewing the Picture in Picture (PIP)............................................................... 37
■ Using the Digital NR (Noise Reduction) Feature ........................................... 40
■ Preventing Screen Burn-in............................................................................... 41
■ Reducing the Effects of Screen Burn................................................................ 42
■ Changing the Sound Standard ...................................................................... 43
English - 4
Page 5
Contents (continued)
◆ USING YOUR DISPLAY (continued)
■ Customizing the Sound Settings ................................................................... 44
■ Adjusting the Volume Automatically .............................................................. 44
■ Setting the TruSurround XT........................................................................... 45
■ Selecting the Internal Mute............................................................................ 46
■ Setting the Melody Sound ............................................................................. 46
■ Selecting the Sound Mode (depending on the model) .................................. 47
■ Setting and Displaying the Current Time....................................................... 48
■ Setting the Sleep Timer ................................................................................. 49
■ Switching the Television On and Off Automatically ....................................... 50
■ Viewing an External Signal Source ............................................................... 52
■ Redirecting an Input to the External Output .................................................. 53
◆ USING THE TELETEXT FEATURE
■ Teletext Feature ............................................................................................ 54
■ Displaying the Teletext Information ............................................................... 55
■ Selecting Display Options.............................................................................. 56
■ Selecting a Teletext Page.............................................................................. 57
◆ ADDITIONAL INFORMATION AND CONNECTIONS
■ Connecting to External Input/Output ............................................................. 58
■ Connecting to the AV Output......................................................................... 59
■ Connecting to the RCA Input......................................................................... 60
■ Connecting to the S-Video Input.................................................................... 60
■ Connecting to the Component Input.............................................................. 61
■ Connecting to the PC Input ........................................................................... 62
■ Connecting Home Theater System ............................................................... 63
■ Setting up Your PC Software (Windows only) .............................................. 64
■ Input Mode (PC) ............................................................................................ 65
◆ RECOMMENDATIONS FOR USE
■ Troubleshooting: Before Contacting Service Personnel................................ 66
Symbols
Press Important Note
☛
➢
English - 5
Page 6
Control Panel
Front of the TV
The actual configuration of your TV may be different, depending on
➢
your model.
Speaker
a) SOURCE button
Select the external input source.
b) MENU button
Display the on-screen menu.
c) (+,-) buttons
Adjust the volume.
d) C/P. ( , ) buttons
Select channels.
◆ You can use the
➢
English - 6
depending on the model.
◆ The (+,-
buttons on the remote control.
◆ If the remote control no longer works or you have misplaced it, you can use the controls
on the panel of the TV.
C/P.
) and
C/P.
(
,
(
,
e)
(
ENTER) button
Confirm your choice (Store or Enter).
f)
(
POWER) button
Press to turn the TV on and off.
Power Indicator
- Power Off: Blue
- Power On: Off
g) Remote Control Sensor
Aim the remote control towards this spot on the TV.
) buttons to switch on the TV when it is in standby mode
) buttons have the same function as the ▲/▼/œ/√
Page 7
Control Panel (continued)
The actual configuration of your TV may be different, depending on
➢
your model.
Rear Panel
a) AV OUT (VIDEO / AUDIO L/R)
Outputs for external devices.
b) AV IN (VIDEO / AUDIO L/R)
Video and audio inputs for external devices, such
as a camcorder or VCR.
c) PC IN / AUDIO
Connect to the video and audio output jack on
your PC.
d) S-VIDEO
Video input for external devices with an S-Video
output, such as a camcorder or VCR.
e) COMPONENT IN
Video (Y/PB/PR) and audio (AUDIO L/R) inputs for
Component.
For further details about connection, refer to pages 58~63.
➢
Whenever you connect an audio or video system to your television, ensure that all
➢
elements are switched off. Refer to the documentation supplied with your equipment for
detailed connection instructions and associated safety precautions.
f) EXT 1, EXT 2
Inputs or outputs for external devices, such as
VCR, DVD, video game device or video disc
players.
g) ANT IN (75Ω)
75Ω Coaxial connector for Aerial/Cable Network.
h) SERVICE
Connector for service only.
i) POWER IN
Connect the supplied power cord.
English - 7
Page 8
Infrared Remote Control
TURNS THE TV ON AND OFF
DIRECT CHANNEL SELECTION
AUTOMATIC SWITCH-OFF/
TELETEXT SIZE SELECTION
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
VOLUME DECREASE
MIX BOTH TELETEXT INFORMATION
AND THE NORMAL BROADCAST
-PIP ACTIVATION OR DEACTIVATION
-SOURCE SELECTION (SOURCE)
-CHANNEL SELECTION (P )
TELETEXT DISPLAY/
MENU DISPLAY/
TELETEXT INDEX
MOVE TO THE REQUIRED
ADJUST AN OPTION VALUE
FASTEXT TOPIC SELECTION
MENU OPTION/
RESPECTIVELY
PICTURE STILL
PICTURE SIZE
PIP FUNCTIONS:
(PIP)
-SIZE SELECTION (SIZE)
SWITCH REPEATEDLY BETWEEN THE
LAST TWO CHANNELS DISPLAYED/
TELETEXT SUB-PAGE
NEXT CHANNEL/
TELETEXT NEXT PAGE
EXTERNAL INPUT SELECTION/
TELETEXT PAGE HOLD
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE
INFORMATION DISPLAY/
TELETEXT REVEAL
TV MODE SELECTION/
EXIT MENU/
EXIT TELETEXT
(DEPENDING ON THE MODEL)
CONFIRM YOUR CHOICE
(STORE OR ENTER)
SOUND MODE SELECTION
TruSurround XT MODE SELECTION
PICTURE EFFECT SELECTION
SOUND EFFECT SELECTION/
TELETEXT CANCEL
ADJUST SCREEN BRIGHTNESS
TO SURROUNDING
ENVIRONMENT
English - 8
The performance of the remote control may be affected by bright light.
➢
Page 9
Inserting the Batteries in the Remote Control
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the television
◆ Find that the remote control is no longer operating
correctly
1 Remove the cover on the rear of the remote control by pressing
the symbol ( ) downwards and then pulling firmly to remove it.
2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆-on the battery against -on the remote control
◆+on the battery against +on the remote control
3 Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
Do not mix battery types, i.e. alkaline and manganese.
➢
Assembling the Stand-Base
1 Assemble the PDP with the stand and firmly secure the PDP using
4 screws provided.
Two or more people should carry the PDP. Never lay the
➢
PDP on the floor because of possible damage to the screen.
Always store the PDP upright.
English - 9
Page 10
Installing the Display on the Wall Attachment Panel
Refer to the correct installation guide according to your wall bracket.
➢
Installation Notes
◆
Contact a technician for installing the wall bracket.
◆
Samsung Electronics is not responsible for any damages to the product or harm to customers when
the installation is done by the customer.
◆
This product is for installing on cement walls. The product may not stay in place when installed on
plaster or wood.
Components
◆
Only use the components and accessories shipped with the product.
Wall Bracket
1 Left: 1 Right: 1
Hinge
Wall Bracket Assembly
1 Insert and tighten the Captive Screw in
the direction of the arrow.
When done, mount the wall bracket on
the wall.
Captive Screw
Hinge (Left)
There are two hinges
(left and right). Use the
correct one.
Wall Bracket
Hinge (Right)
Accessories
Plastic Hanger: 4 Screw : 11
Screw : 4
Anchor : 11
2 Before drilling into the wall, check if the length
between the two locking holes at the back of
the product is correct.
If the length is too short or long, loosen all or
some of the 4 screws on the wall bracket to
adjust the length.
Length between the
two locking holes
3 Check the installation diagram and mark the drill
points on the wall. Use the 5.0 mm bit to drill holes
deeper than 35 mm.
Fix each anchor in the corresponding hole.
Match each of the brackets and hinge holes to the
corresponding anchor holes and insert and tighten
the 11 screws .
English - 10
Page 11
Installing the Display on the Wall Attachment Panel (continued)
To mount the product on the wall bracket
◆ The shape of the product may vary depending on the model. (The assemblies of the plastic hanger
and the screw are the same)
1 Remove the 4 screws on the back of the product.
3 Tighten the 4 screws in step 2 (plastic hanger
+ screw ) to the rear holes of the product.
2 Insert the screw into the plastic hanger.
(See the figure below)
◆ Mount the product on the wall bracket
☛
4
Remove safety pin (#) and insert the 4 product
holders into the corresponding bracket holes (
place the product (
bracket. Make sure to reinsert and tighten the safety
pin (
and make sure it is properly fixed to
the left and right plastic hangers.
◆ Be careful when installing the product
on the bracket as fingers can be
caught in the holes.
◆ Make sure the wall bracket is securely
fixed to the wall, or the product may not
stay in place after installation.
!). Then
@) so that it is firmly fixed to the
#) to securely hold the product to the bracket.
PDP
Wall Bracket Angle Adjustment
Adjust the bracket angle to -
➢
1 Fix the product to the wall bracket.
2 Hold the product at the top in the center and pull it
forward (direction of the arrow) to adjust the angle.
(See the figure to the right)
3 You can adjust the bracket angle between -2° and 15°.
2obefore installing it on the wall.
Wall Bracket
Make sure to use the top center,
and not the left or the right side of
the product to adjust the angle.
Wall
English - 11
Page 12
Rear of the TV
Connecting to an Aerial or Cable Television Network
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
◆ A satellite network
1 In these cases, connect the aerial or network input cable to
the ANT IN jack on the rear of the television.
2 If you are using an indoor aerial, you may need to turn it when
tuning your television until you obtain a picture that is both sharp
or
Cable Television
Network
and clear.
For further details, refer to:
◆ “Storing Channels Automatically” on page 17
◆ “Storing Channels Manually” on page 18
When installing or re-installing your TV, be sure to use the
➢
supplied coaxial antenna cable. If you connect using a different
coaxial cable, there is risk of noise or interference to the screen
image. (You must not use another general purpose cable.
Use the 3M/5M/7M cable supplied by Samsung.)
Connecting a Satellite Receiver or Decoder
In order to watch television programmes broadcast via a satellite network,
Rear of the TV
Satellite receiver/
Decoder
you must connect a satellite receiver to the rear of TV. Also, in order to
descramble a coded transmission signal, you must connect a decoder to
the rear of TV.
Using a SCART cable
Connect the receiver (or decoder) SCART cable to one of the
SCART connectors on the rear of the television.
Using a coaxial cable
Connect a coaxial cable to the:
◆ Receiver (or Decoder) output socket.
◆ Television aerial input socket.
If you wish to connect both a satellite receiver (or decoder) and
➢
a VCR, you should connect the:
◆ Receiver (or Decoder) to the VCR
◆ VCR to the television
Otherwise, connect the receiver (or decoder) directly to the
television.
English - 12
Page 13
Switching Your Television On and Off
The mains lead is attached to the rear of your television.
1 Plug the mains lead into an appropriate socket.
Result
: The Standby indicator on the front of the television
lights up.
The main voltage is indicated on the rear of the television
➢
and the frequency is 50 or 60Hz.
2 Press the power button on the front of the television (or POWER
() button on the remote control) to switch the television on.
Result
: The programme that you were watching last is
re-selected automatically.
If you have not yet stored any channels, no clear picture
➢
appears. Refer to “Storing Channels Automatically” on page
17 or “Storing Channels Manually” on page 18.
3 To switch your television off, press the power button again.
Front of the TV
English - 13
Page 14
Familiarizing Yourself with the Remote Control
The remote control is used mainly to:
◆ Change channels and adjust the volume.
◆ Set up the television using the on-screen menu system.
The following table presents the most frequently used buttons and
their functions.
Button Viewing Function Menu Function
Used to display the next
stored channel.
Used to display the
previous stored channel.
to
Used to display the corresponding channels.
➢
For double digit channels, the second digit must be
pushed immediately after the first. Failure to do this
will result in a single digit channel being displayed.
Used to increase the volume.
Used to decrease the volume.
-
-
MUTE
()
MENU
()
EXIT/TV
()
PRE-CH
Used to switch the sound off temporarily.
➢
To turn the sound back on, press this button
again, or press the or button.
Used to display the
on-screen menu system.
-
-
Press the
channel viewed. To quickly switch between two channels
that are far apart, select the first channel, then use the
numeric buttons to select the second channel. Then, use the
PRE-CH button to quickly alternate between them.
PRE-CH button. The TV will switch to the last
Used to return to the previous
menu or normal viewing.
Used to:
◆ Display a sub-menu
containing selections for
the current menu option.
◆ Increase/decrease a
menu option value.
Used to confirm your choice.
Used to exit from the menu
system and return to normal
viewing directly.
English - 14
Page 15
Plug & Play Feature
When the television is initially powered on, several basic customer
settings proceed automatically and subsequently.
The following settings are available.
1 If the television is in standby mode, press the POWER ()button
on the remote control.
Result
: The message to start Plug & Play is displayed.
2 To start Plug & Play, press the ENTER () button.
Result
: The Language menu is displayed.
The Language menu will automatically appear after several
➢
seconds, even if the
ENTER () button is not pressed.
3 Select the appropriate language by pressing the … or † button.
Press the
Result
ENTER () button.
: The message to check the connected status of the
antenna is displayed.
4 Make sure that the antenna is connected to the TV.
Press the
Result
ENTER () button.
: The Country menu is displayed.
5 Select your country or area by pressing the … or † button.
Press the
Result
ENTER () button.
: The menu to select channels is displayed.
6 To start channel store, press the ENTER () button.
Result
: The search will end automatically. Channels are sorted
and stored in the order which reflects their position in
the frequency range (with lowest first and highest last).
When this has finished, the menu to set the time will be
displayed.
To stop the search before it has finished or return to normal
➢
viewing, press the
Press the ENTER () button to set the clock.
➢
MENU () or the ENTER () button.
Plug & Play
Start Plug & Play
OK
Enter Exit
Plug & Play
Language
Move Enter Skip
Check antenna input.
Country
Move Enter Skip
Auto Store
P1 C
English
Deutsch
Français
Plug & Play
OK
Enter Skip
Plug & Play
Belgium
France
Germany
Plug & Play
--
Start
Enter Skip
Plug & Play
40 MHz
0 %
7 Press the œ or √ button to select the hour or minute.
Set these by pressing the
You can enter the hours or minutes by using the
➢
numeric buttons on the remote control.
… or † button.
8 The settings are complete, and the stored channel will be
activated.
--
Clock Set
Enter Skip
Plug & Play
Clock Set 00 : 00
Move Adjust Enter Skip
Enjoy your viewing
OK
English - 15
:
--
Page 16
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
Plug & Play Feature (continued)
To activate Plug & Play on the menu, follow the instructions below.
Setup
: Off
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Setup.
Result
: The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the ENTER () button again to select Plug & Play.
Result
: The message to start Plug & Play is displayed.
5 For further details on settings, refer to the previous page.
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
Choosing Your Language
When you start using your television for the first time, you must
Setup
: Off
Setup
Deutsch
Français
Nederlands
Español
: Off
English
select the language which will be used for displaying menus and
indications.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Setup.
Result
: The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Language.
Press the
Result
: The available languages are listed.
5 Select the appropriate language by pressing the … or † button.
Press the
ENTER () button.
ENTER () button.
English - 16
Page 17
Storing Channels Automatically
You can scan for the frequency ranges available to you (availability
depends on your country). Automatically allocated programme numbers
may not correspond to actual or desired programme numbers. However
you can sort numbers manually and clear any channels you do not wish
to watch.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Channel.
Result
: The Channel menu is displayed.
3 Press the ENTER () button.
Result
: The Country is selected.
4 Press the ENTER () button again.
Result
: The available countries are listed.
5 Select your Country by pressing the … or † button.
➢ If you have selected the Others option but do not wish to
scan the PAL frequency range, store the channels manually
(“Storing Channels Manually” on page 18).
6 Press the ENTER () button.
7 Press the … or † button to select Auto Store.
Press the
Result
8 Press the ENTER () button again to start the search.
Result
➢ To stop the search before it has finished, press the MENU
9 When the channels have been stored, you can:
◆ Sort them in the order required (“Sorting the Stored
◆ Clear a channel (“Skipping Unwanted Channels” on page 20).
◆ Fine-tune channel reception if necessary (“Fine Tuning
◆ Assign a name to the stored channels (“Assigning Names to
◆ Activate/deactivate the Digital NR (Noise Reduction) feature
◆ Activate/deactivate the LNA (Low Noise Amplifier) feature
ENTER () button.
: The Auto Store menu is displayed.
: The search will end automatically. Channels are sorted
and stored in an order which reflects their position in
the frequency range (with lowest first and highest last).
The programme originally selected is then displayed.
() or the ENTER () button.
Channels” on page 21).
Channel Reception” on page 25).
Channels” on page 22).
(“Using the Digital NR (
(“Using the LNA (
Noise Reduction) Feature” on page 40).
Low Noise Amplifier) Feature” on page 24).
TV
Country : Belgium
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
TV
Country : Belgium
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
TV
Country : Belgium
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
Auto Store
P1 C
Channel
Channel
Germany
Netherlands
Channel
--
40 MHz
Start
Enter Return
Belgium
France
Italy
Spain
0 %
English - 17
Page 18
TV
Country : Belgium
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
TV
Programme : P 1
Colour System : AUTO
Sound System : BG
Channel : C 5
Search : 175 MHz
Store : ?
Move Enter Return
TV
Programme : P 1
Colour System : AUTO
Sound System : BG
Channel : C 2
Search : 48 MHz
Store : ?
Move Enter Return
TV
Programme : P 1
Colour System : AUTO
Sound System : BG
Channel : C 2
Search : 48 MHz
Store : ?
Storing Channels Manually
You can store television channels, including those received via cable
Channel
Manual Store
Manual Store
AUTO
PAL
SECAM
NTSC 4.43
Manual Store
BG
DK
I
L
networks.
When storing channels manually, you can choose:
◆ Whether or not to store each of the channels found.
◆ The programme number of each stored channel which you
wish to identify.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Channel.
Result
: The Channel menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Manual Store.
Press the
ENTER () button.
5 If necessary, select the broadcasting standard required.
Press the
Press the
… or † button to select Colour System.
ENTER () button.
6 Select the required colour standard by pressing the … or †
button. Press the ENTER () button.
Result
: The following options are available.
(depending on the model)
AUTO - PAL - SECAM - NTSC 4.43
7 Press the … or † button to select Sound System.
Press the
ENTER () button.
8 Select the required sound standard by pressing the … or †
button. Press the ENTER () button.
Result
: The following options are available.
BG - DK - I - L
Move Enter Return
English - 18
Page 19
Storing Channels Manually (continued)
9 If you know the number of the channel to be stored, see the
following steps.
◆
Press the … or † button to select Channel.
Press the
◆
Press the … or † button to select C (Air channel) or
ENTER () button.
S (Cable channel).
◆
Press the √ button.
◆
Press the … or † button to select the required number.
Press the
If there is abnormal sound or no sound, re-select the
➢
ENTER () button.
sound standard required.
10 If you do not know the channel numbers, select Search by
pressing the
Press the
Press the
Result
… or † button. Press the ENTER () button.
… or † button to start the search.
ENTER () button.
: The tuner scans the frequency range until the first
channel or the channel that you selected is received on
your screen.
11 To assign a programme number to a channel, select Programme
by pressing the … or † button. Press the ENTER () button.
12 Press the … or † button until you find the correct number.
Press the
ENTER () button.
13 To store the channel and associated programme number, select
Store by pressing the … or † button. Set to OK by pressing the
ENTER () button.
TV
Programme : P 1
Colour System : AUTO
Sound System : BG
Channel : C 05
Search : 175 MHz
Store : ?
Adjust Enter Return
TV
Programme : P 1
Colour System : AUTO
Sound System : BG
Channel : C 5
Search : 175 MHz
Store : ?
Adjust Enter Return
TV
Programme : P 1
Colour System : AUTO
Sound System : BG
Channel : C 5
Search : 175 MHz
Store : OK
Move Enter Return
Manual Store
Manual Store
Manual Store
14 Repeat steps 9 to 13 for each channel to be stored.
Channel mode
☛
◆ P (Programme mode): When completing tuning, the
broadcasting stations in your area have been assigned to
position numbers from P00 to P99. You can select a
channel by entering the position number in this mode.
◆ C (Air channel mode): You can select a channel by entering
the assigned number to each air broadcasting station in this
mode.
◆ S (Cable channel mode): You can select a channel by entering
the assigned number for each cable channel in this mode.
English - 19
Page 20
TV
Country : Belgium
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
Add/Delete
Skipping Unwanted Channels
You can exclude the channels of your choice from the channel scan
Channel
operation. When you scan through the stored channels, those that you
have chosen to skip are not displayed.
All channels that you do not specifically choose to skip are displayed
during scanning.
1 Press the MENU () button.
Result
: The main menu is displayed.
2 Press the … or † button to select Channel.
Result
: The Channel menu is displayed.
P 1 Not in Memory
Add
Change Enter Return
Add/Delete
P 1 In Memory
Delete
Change Enter Return
3 Press the ENTER () button.
4 Press the … or † button to select Add/Delete.
Press the
Result
ENTER () button.
: The Add/Delete menu is displayed with the current
channel selected.
5 Press the P or button to delete or add the required
channel.
Press the
ENTER () button.
6 Repeat step 5 for each channel to be deleted or added.
English - 20
Page 21
Sorting the Stored Channels
This operation allows you to change the programme numbers of
stored channels. This operation may be necessary after using auto store.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Channel.
Result
: The Channel menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Sort.
Press the
5 Select the channel that you wish to move by pressing the … or †
button. Press the ENTER () button.
6 Select the number of the programme to which the channel is to
be moved by pressing the
Press the
Result
7 Repeat steps 5 to 6 until you have moved all the channels to the
required programme numbers.
ENTER () button.
… or † button.
ENTER () button.
: The channel is moved to its new position and all other
channels are shifted accordingly.
TV
Country : Belgium
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
TV
Prog. Channel Name
0C
1C 7
2C 19
3C 25
4C 26
Move Enter Return
TV
Prog. Channel Name
0C
2C 19
3C 25
4C 26
Channel
Sort
--
Sort
--
C 7
Move Enter Return
English - 21
Page 22
TV
Country : Belgium
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
Assigning Names to Channels
Channel names will be assigned automatically when channel information is
Channel
broadcast. These names can be changed, allowing you to assign new
names.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Channel.
Result
: The Channel menu is displayed.
TV
Prog. Channel Name
0C
1C 7
2C 19
3C 25
4C 26
Move Enter Return
TV
Prog. Channel Name
0C
1C 7 A
2C 19
3C 25
4C 26
Move Adjust Return
Name
-- -----
-----
-----
-----
-----
Name
-- -----
-----
-----
-----
3 Press the ENTER () button.
4 Press the … or † button to select Name.
Press the
Result
ENTER () button.
: The Name menu is displayed with the current channel
selected.
5 Press the … or † button to select the channel to be assigned to a
new name. Press the
Result
: Arrow indications are displayed around the name box.
ENTER () button.
6 Press the … or † button to select a letter (A~Z), a number (0~9),
or a symbol. Move on to the previous or next letter by pressing the
œ or √ button.
7 Press the ENTER () button.
8 Repeat steps 5 to 7 for each channel to be assigned to a new
name.
English - 22
Page 23
Locking the Channel
This feature allows you to prevent unauthorized users, such as children,
from watching unsuitable programmes by muting out video and audio.
Child Lock cannot be released using front panel buttons. Only remote
control can release the Child Lock setting, so keep the remote control
away from children.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Setup.
Result
: The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Child Lock.
Press the
5 Press the ENTER () button again.
Select
Press the
ENTER () button.
On by pressing the … or † button.
ENTER () button.
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
TV
Child Lock : On
Programme : P 1
Lock : ?
Move Enter Return
Setup
: Off
Child Lock
6 Press the … or † button to select Programme.
Press the
ENTER () button.
7 Select the number of programme to which the channel is to be
locked by pressing the
Press the
ENTER () button.
… or † button.
8 Press the … or † button to select Lock.
Select
Locked by pressing the ENTER () button.
Result
: The selected channel is locked and marked with the
◆ A Blue screen is displayed when the Child Lock is
➢
activated.
◆ To unlock the Channel lock, press the ENTER ()
button again. The locked channel is unlocked.
◆ When a channel is locked, the channel is marked with
the symbol on the left side in the Channel OSD (On
Screen Display).
symbol.
TV
Child Lock : On
Programme : 01
Lock : ?
Adjust Enter Return
TV
Child Lock : On
Programme : P 1
Lock : Locked
Move Enter Return
P 1
Mono
Child Lock
Child Lock
English - 23
Page 24
TV
Country : Belgium
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
Using the LNA (Low Noise Amplifier) Feature
This function is very useful in the situation that the TV is used in weak
Channel
signal. LNA amplifies the TV signal in the weak signal area, a low-noise
preamplifier boosts the incoming signal.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Channel.
Result
: The Channel menu is displayed.
TV
Country : Belgium
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
Channel
Off
On
3 Press the ENTER () button.
4 Press the … or † button to select LNA.
Press the
ENTER () button.
5 Select Off or On by pressing the … or † button.
Press the
➢
ENTER () button.
◆ If the picture is noisy with the LNA set to On, select Off .
◆ LNA setting is to be made for each channel.
English - 24
Page 25
Fine Tuning Channel Reception
If the reception is clear, you do not have to fine tune the channel,
as this is done automatically during the search and store operation.
If the signal is weak or distorted, you may have to fine tune the
channel manually.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Channel.
Result
: The Channel menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Fine Tune.
Press the
Result
ENTER () button.
: The horizontal bar is displayed.
TV
Country : Belgium
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
Fine Tune
P 1
Adjust Save
Channel
0
Reset
Return
5 To obtain a sharp and clear picture and good sound quality,
press the
œ or √ button until you reach the optimal setting.
6 To store the fine tuning setting in the TV’s memory, press the
ENTER () button.
Result
: The programme number changes to Red and is
marked with a “
*”.
7 To reset the fine tuning to 0, select Reset by pressing the … or †
button then press the ENTER () button.
If you are unable to fine tune a channel, check that the
➢
Colour System and Sound System settings are correct.
Fine Tune Store will change the colour of the Channel OSD (On
➢
Screen Display) from White to Red and add the “
*” mark.
P 1
Adjust Save
P 1 *
Adjust Save
P 1 *
Mono
Fine Tune
3
Reset
Return
Fine Tune
3
Reset
Return
English - 25
Page 26
Displaying Information
P 1
Mono
Picture : Dynamic
Sound : Custom
SRS TSXT : Off
12:00
Changing the Picture Standard
You can view the channel information and setting status you have
selected by pressing the “INFO
()
” button on the remote
control.
The information displayed varies according to the selected source.
TV
Mode : Dynamic
Size : Auto Wide
Digital NR : On
DNIe Demo : Off
My Colour Control
Energy Saving : S tandard
PIP
Move Enter Return
TV
Mode : Dynamic
Contrast 100
Brightness 50
Sharpness 75
Colour 55
Tint G 50 R 50
Colour Tone : Cool2
Reset
Move Enter Return
TV
Mode : Dynamic
Contrast 100
Brightness 50
Sharpness 75
Colour 55
Tint G 50 R 50
Colour Tone : Cool2
Reset
Move Enter Return
Picture
Mode
Mode
Dynamic
Standard
Movie
Custom
You can select the type of picture which best corresponds to your
viewing requirements.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Picture.
Result
:
The
Picture menu is displayed.
3 Press the ENTER () button.
Result
:
The
Mode is selected.
4 Press the ENTER () button again.
Result
The
:
Mode menu is displayed.
5 Press the ENTER () button.
Result
: The following
Dynamic - Standard - Movie - Custom
options
are available.
6 Select the required option by pressing the … or † button.
7 Press the ENTER () button.
You can also set these options simply by pressing the
➢
P.MODE (: Picture Mode) button on the remote
control.
English - 26
Page 27
Customizing the Picture Settings
Your television has several setting options that allow you to control
the picture quality.
1 Press the MENU ()button.
: The main menu is displayed.
Result
2 Press the … or † button to select Picture.
:
The
Result
Picture menu is displayed.
TV
Mode : Dynamic
Size : Auto Wide
Digital NR : On
DNIe Demo : Off
My Colour Control
Energy Saving : S tandard
PIP
Picture
3 Press the ENTER () button.
:
The
Result
Mode is selected.
4 Press the ENTER () button again.
:
The
Result
Mode menu is displayed.
5 Press the ENTER () button.
: The following
Result
Dynamic - Standard - Movie - Custom
options
are available.
6 Select the required option by pressing the … or † button.
7 Press the ENTER () button.
8 Select the required option by pressing the … or † button.
: The following
Result
◆ Contrast - Brightness - Sharpness - Colour -
◆ Contrast - Brightness : PC Mode.
Tint (NTSC only)
options
are available.
9 Press the ENTER () button.
: The horizontal bar is displayed.
Result
➢
Press the
œ or √ button until you reach the optimal
setting.
◆ Press the … or † button to select other option(s).
◆ The settings values may vary depending on the input
source. (ex. RF, Video, Component, or PC.)
Move Enter Return
TV
Mode : Custom
Contrast 90
Brightness 50
Sharpness 75
Colour 50
Tint G 50 R 50
Colour Tone : Normal
Reset
Contrast 90
TV
Mode : Custom
Contrast 90
Brightness 50
Sharpness 75
Colour 50
Tint G 50 R 50
Colour Tone : Normal
Reset
Mode
Move Enter Return
Mode
Cool2
Cool1
Normal
Warm1
Warm2
Move Enter Return
10 Press the MENU () button to return to Mode menu.
Press the
Press the
… or † button to select Colour Tone.
ENTER () button.
11 Select the required option by pressing the … or † button.
: The following
Result
Cool2 - Cool1 - Normal - Warm1 - Warm2
options
are available.
12 Press the ENTER () button.
13 To return the factory defaults, select Reset by pressing the … or
† button. Press the ENTER () button.
: The previously adjusted settings will be reset to the
Result
➢
➢
factory defaults.
The reset function is set for each mode (Dynamic,
Standard, Movie, or Custom).
The reset function is also set for each Colour Tone (Cool2,
Cool1, Normal, Warm1, or Warm2).
TV
Mode : Custom
Contrast 90
Brightness 50
Sharpness 75
Colour 50
Tint G 50 R 50
Colour Tone : Normal
Reset
Move Enter Return
English - 27
Mode
Page 28
Setting the Picture (PC Mode)
Preset to the PC mode by pressing the SOURCE () button.
➢
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
TV
Image Lock
Position
Auto adjustment
Image Reset
Move Enter Return
TV
Coarse 50
Fine 0
Image Lock
Setup
: Off
PC
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Setup.
Result
: The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select PC.
Press the
Result
ENTER () button.
: The PC menu is displayed.
5 Press the … or † button to select Image Lock.
Press the ENTER () button.
6 Press the … or † button to select the option (Coarse or Fine) to
be adjusted. Press the
Result
: The horizontal bar is displayed.
Press the
setting.
Press the … or † button to select other option(s).
➢
ENTER () button.
œ or √ button until you reach the optimal
7 Press the ENTER () button.
8 Press the MENU ()button.
Result
: The PC menu is displayed again.
Coarse
TV
TV
Move Enter Return
PC
Image Lock
Position
Auto adjustment
Image Reset
Move Enter Return
Position
Move Enter Return
9 Press the … or † button to select Position.
Press the
ENTER () button.
10 Adjust the position by pressing the …, †, œ, or √ button.
50
11 Press the ENTER () button.
English - 28
Page 29
Setting the Picture (PC Mode) (continued)
Preset to the PC mode by pressing the SOURCE () button.
➢
12 Press the … or † button to select Auto adjustment.
Press the
Result
ENTER () button.
: The screen quality and position are automatically reset.
The settings are all finished, and the TV will
automatically return to the previous picture.
13 To return the factory defaults, select Image Reset by pressing
the
… or † button. Press the ENTER () button.
Result
: The previously adjusted settings will be reset to the
factory defaults.
TV
Image Lock
Position
Auto adjustment
Image Reset
Move Enter Return
Auto Adjustment in progress
Please wait
TV
Image Lock
Position
Auto adjustment
Image Reset
Move Enter Return
PC
PC
Image Reset has completed.
Return
English - 29
Page 30
TV
TV
PC Mode
TV
Selecting the Picture Size
Picture
Mode : Dynamic
Size : Auto Wide
Digital NR : On
DNIe Demo : Off
My Colour Control
Energy Saving : S tandard
PIP
Move Enter Return
Size
Auto Wide
Wide
Wide 4:3
Panorama
Zoom
4:3
Move Enter Return
Size
Auto Wide
Wide
Wide 4:3
Panorama
Zoom
4:3
Move Enter Return
You can select the picture size which best corresponds to your viewing
requirements.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Picture.
Result
: The Picture menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Size.
Press the
ENTER () button.
5 Select the required option by pressing the … or † button.
Result
: The following options are available.
◆ Auto Wide : Expanding and pulling up the picture from 4:3
to 16:9 ratio.
◆ Wide : Sets the picture to 16:9 wide mode.
◆ Wide 4:3 : Magnify the size of the picture more than 4:3.
Move the screen up/down using the
… or †
button after selecting the by pressing the √
or ENTER ()button.
◆ Panorama : Use this mode for the wide aspect ratio of a
panoramic picture.
◆ Zoom : Magnify the size of the picture vertically on
screen.
◆ 4:3 : Sets the picture to 4:3 normal mode.
6 Press the ENTER () button.
◆ You can select these options simply by pressing the P.SIZE
➢
button on the remote control.
◆ If you change the picture size when PIP is On, PIP will
automatically be turned Off.
◆ Depending on the input source, the P.SIZE options may vary.
English - 30
Positioning and Sizing the screen using Zoom
◆ Resizing the screen using the Zoom enables the positioning
➢
and sizing of the screen to up/down direction using the
† button as well as the screen size.
◆ Move the screen up/down using the … or † button after
selecting the by pressing the œ or √ button.
◆ Resize the screen vertically using the … or † button after
selecting the by pressing the
œ or √ button.
◆ Screen enlargement operates only in TV/Video/S-Video/
Component input modes.
◆ PC mode prevents the screen enlargement function.
… or
Page 31
Viewing the DNIe Demonstration
This TV includes the DNIe function so as to provide a high visual
quality.
If you set DNIe Demo to On, you can view an applied DNIe and a
normal picture on the screen, for demonstration purposes. Using
this function, you can view the difference in the visual quality.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Picture.
Result
: The Picture menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select DNIe Demo.
Press the
5 Select Off or On by pressing the … or † button.
Result
◆ On : Switches on the DNIe Demo mode.
◆ Off : Switches off the DNIe Demo mode.
6 Press the ENTER () button.
ENTER () button.
: The following options are available.
TV
Mode : Dynamic
Size : Auto Wide
Digital NR : On
DNIe Demo : Off
My Colour Control
Energy Saving : S tandard
PIP
TV
Mode : Dynamic
Size : Auto Wide
Digital NR : On
DNIe Demo : Off
My Colour Control
Energy Saving : S tandard
PIP
DNIe Off DNIe On
Picture
Move Enter Return
Picture
Off
On
Move Enter Return
DNIe Demo
DNIeTM(Digital Natural Image engine)
➢
This feature brings you more detailed image with 3D noise
reduction, detail enhancement, contrast enhancement and
white enhancement. New image compensation Algorithm
gives brighter, clearer, more detailed image to you.
TM
DNIe
technology will fit every signal into your eyes.
Freezing the Current Picture
You can freeze the picture when watching a television programme
simply by pressing the “STILL” button. To return to normal
viewing, press it again.
In the PIP mode, the main and sub pictures are stilled at
➢
the same time.
This function will automatically cancel after 5 minutes.
➢
English - 31
Page 32
TV
Mode : Dynamic
Size : Auto Wide
Digital NR : On
DNIe Demo : Off
My Colour Control
Energy Saving : S tandard
PIP
Setting the My Colour Control (Easy Control)
This feature allows you to adjust colours according to your preferences, by
Picture
adjusting skin, sky, and grass tones using the predefined settings (Blue,
Green, Pink, Standard, and Custom) without affecting other colours on
the screen.
1 Press the MENU ()button.
Result
: The main menu is displayed.
Move Enter Return
TV
Original Blue
Blue Green Pink
Move
My Colour Control
Easy Control : Custom
Detail Control
Move Enter Return
Easy Control
Enter
Return
2 Press the … or † button to select Picture.
Result
: The Picture menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select My Colour Control.
Press the
Result
ENTER () button.
: The Easy Control is selected.
5 Press the ENTER () button again.
Result
: The following options are available.
◆ Blue
Emphasizing clear blues.
◆ Green
Emphasizing mild greens.
◆ Pink
Emphasizing warm skin colours.
√
◆ Standard
Standard picture.
◆ Custom
Changing the settings in the Detail Control
menu will automatically set to Custom (see next
page).
6 Select the required option by pressing the œ or √ button.
Result
: The original picture (before adjustment) is shown on
the left side, while the selected mode is shown on the
right side.
English - 32
7 Press the ENTER () button.
◆ Depending on the input source, this feature may not
➢
operate.
◆ When running the My Colour Control feature, the current
picture is captured as a still image before being displayed on
the screen.
◆ You cannot use this function, when PIP is On.
Page 33
Setting the My Colour Control (Detail Control)
This setting can be adjusted to suit your personal preferences.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Picture.
Result
: The Picture menu is displayed.
3 Press the ENTER () button.
TV
Mode : Dynamic
Size : Auto Wide
Digital NR : On
DNIe Demo : Off
My Colour Control
Energy Saving : S tandard
PIP
Move Enter Return
Picture
4 Press the … or † button to select My Colour Control.
Press the
ENTER () button.
5 Press the … or † button to select Detail Control.
Press the
ENTER () button.
6 Select the required option (Pink, Green , or Blue) by pressing the
▲ or ▼ button. Press the ENTER () button.
7 Press the œ or √ button until you reach the optimal setting.
Result
: Changing the adjustment value will refresh the
adjusted screen.
Press the ▲ or ▼ button to select other option(s).
➢
8 Press the MENU ()button.
Result
: The Detail Control menu is displayed again.
9 To return the factory defaults, select Reset by pressing the
▲ or ▼ button. Press the ENTER () button.
Result
: The previously adjusted colours will be reset to the
factory defaults.
TV
TV
Original Adjusted
Pink
Move
My Colour Control
Easy Control : Custom
Detail Control
Move Enter Return
Detail Control
Pink 50
Green 50
Blue 50
Reset
Move Enter Return
Detail Control
Adjust
50
Return
TV
Pink 50
Green 50
Blue 50
Reset
Detail Control
Move Enter Return
English - 33
Page 34
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
Setting the Blue Screen
If no signal is being received or the signal is very weak, a blue screen
Setup
: Off
Setup
: Off
Off
On
automatically replaces the noisy picture background. If you wish to
continue viewing the poor picture, you must set the Blue Screen mode to
Off.
1 Press the MENU ()button.
Result
2 Press the … or † button to select Setup.
Result
3 Press the ENTER () button.
4 Press the … or † button to select Blue Screen.
Press the
5 Select Off or On by pressing the … or † button.
Press the
Blue Screen is displayed while there is no signal from the
➢
external device in the external mode, regardless of the
Screen
: The main menu is displayed.
: The Setup menu is displayed.
ENTER () button.
ENTER () button.
Blue
Setting.
English - 34
Page 35
Using the Colour Weakness Enhancement Feature
This feature adjusts the red, green, or blue colour to enhance the picture
according to the user's particular colour weakness.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Setup.
Result
: The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Colour Weakness.
Press the
Result
ENTER () button.
: The Colour Weakness menu is selected.
5 Press the ENTER () button again.
Press the
Press the
… or † button to select On.
ENTER () button.
6 Select the required option (Red, Green , or Blue) by pressing the
▲ or ▼ button. Press the ENTER () button.
Result
: The horizontal bar is displayed.
Press the
œ or √ button until you reach the optimal
setting.
Press the … or † button to select other option(s).
➢
7 Press the ENTER () button.
TV
TV
TV
Setup
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
Colour Weakness
Red 0
Green 0
Blue 0
Move Enter Return
Colour Weakness
Red 0
Green 0
Blue 0
: Off
Colour Weakness
: Off
Off
On
Colour Weakness
:On
Move Enter Return
Colour Weakness
Red
Move Adjust Return
English - 35
0
Page 36
TV
Mode : Dynamic
Size : Auto Wide
Digital NR : On
DNIe Demo : Off
My Colour Control
Energy Saving : S tandard
PIP
Move Enter Return
TV
Mode : Dynamic
Size : Auto Wide
Digital NR : On
DNIe Demo : Off
My Colour Control
Energy Saving : Standard
PIP
Move Enter Return
Using the Energy Saving Feature
This feature adjusts the screen brightness automatically depending on the
Picture
Picture
Auto Saving
Standard
Super Saving
surrounding lighting conditions.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Picture.
Result
: The Picture menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Energy Saving.
Press the
ENTER () button.
5 Select the required option by pressing the … or † button.
Result
: The following
◆ Auto Saving:
surrounding illumination.
◆ Standard:
regardless of the surrounding illumination.
◆ Super Saving:
saving mode regardless of the surrounding
illumination.
options
are available.
Automatically adjusts to the
Operates in standard mode
Enters maximum power
6 Press the ENTER () button.
This feature is not available when the input source is in PC mode.
➢
You can select these options by simply pressing the
➢
E.SAVING button on the remote control.
English - 36
Page 37
Viewing the Picture in Picture (PIP)
You can display a sub picture within the main picture of a TV program or
external A/V devices. In this way you can watch TV program or monitor
the video input from any connected devices while watching TV or other
video input.
1 Press the MENU ()button.
Result
: The main menu is displayed.
TV
Mode : Dynamic
Size : Auto Wide
Digital NR : On
DNIe Demo : Off
My Colour Control
Energy Saving : S tandard
PIP
Picture
2 Press the … or † button to select Picture.
Result
: The Picture menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select PIP.
Press the
Result
ENTER () button.
: The PIP is selected.
5 Press the ENTER () button again.
To activate, set
Press the
PIP to on by pressing the … or † button.
ENTER () button.
6 Press the … or † button to select Source.
Press the
Result
ENTER () button.
: The following options are available.
TV - Ext.1 - Ext.2 - AV - S-Video
7 Select a source of the sub picture by pressing the … or † button.
Press the
ENTER () button.
8 Press the … or † button to select Swap.
Press the
Result
➢
ENTER () button.
: The main picture and sub picture are interchanged.
You cannot use the Swap function for PC or COMP.
9 Press the … or † button to select Size.
Press the
Result
ENTER () button.
: The following options are available.
Move Enter Return
TV
PIP : On
Source : TV
Swap
Size
Position
Programme : P 1
Move Enter Return
TV
PIP : On
Source : TV
Swap
Size
Position
Programme : P 1
Move Enter Return
TV
PIP : On
Source : TV
Swap
Size
Position
Programme : P 1
PIP
:
:
PIP
:
:
PIP
:
:
Off
On
TV
Ext.1
Ext.2
AV
S-Video
(Large)
-
(Double Window) -(Double Wide)
The Double Window or Double Wide mode can not be
➢
selected in
PC mode.
10 Select a size of the sub picture by pressing the … or † button.
Press the
ENTER () button.
Move Enter Return
TV
PIP : On
Source : TV
Swap
Size
Position
Programme : P 1
Move Enter Return
English - 37
PIP
:
:
Page 38
Viewing the Picture in Picture (PIP) (continued)
TV
PIP : On
Source : TV
Swap
Size
Position
Programme : P 1
Move Enter Return
TV
PIP : On
Source : TV
Swap
Size
Position
Programme : 01
Move Enter Return
PIP
PIP
11 Press the … or † button to select Position.
Press the
Result
:
:
➢
ENTER () button.
: The following options are available.
---
The Position menu is available when the Size is
large ( ) mode.
12 Select a position of the sub picture by pressing the … or †
button. Press the ENTER () button.
13 Press the … or † button to select Programme.
Press the
ENTER () button.
14 Select the channel that you want to view through sub picture by
:
:
pressing the
➢
➢
… or † button.
When the Source is set to TV, you can select the channel
of the sub-picture.
If the sub picture receives no signal and the main picture is
output from a Component or PC signal, the sub picture will
be blue. If the main picture is output from a Video signal,
the sub picture will be black.
15 Press the ENTER () button.
English - 38
Page 39
Viewing the Picture in Picture (PIP) (continued)
Easy functions of the remote control.
Buttons Feature
PIP Used to activate or deactivate the PIP function directly.
SOURCE Used to assign a source of the sub picture (TV, Ext.1 ,
Ext.2, AV , or S-Video).
SIZE Used to select a size of the sub picture ( (Large),
(Double Window), or (Double Wide)).
P/ Used to select a channel of the sub picture.
Table of PIP Settings
Main
Sub
TV XO O O O O O
Ext.1 OX O O O O O
Ext.2 OO X O O O O
AV OO O X O O O
S-Video OO O O X O O
Component
PC
TV Ext.1 Ext.2 AV S-Video Component PC
XX X X X X X
XX X X X X X
X - This PIP combination is not available.
O - This PIP combination is available.
English - 39
Page 40
TV
Mode : Dynamic
Size : Auto Wide
Digital NR : On
DNIe Demo : Off
My Colour Control
Energy Saving : S tandard
PIP
Move Enter Return
Using the Digital NR (Noise Reduction) Feature
If the signal received by your television is weak, you can activate this
Picture
feature to help reduce any static and ghosting that may appear on the
screen.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Picture.
Result
: The Picture menu is displayed.
TV
Mode : Dynamic
Size : Auto Wide
Digital NR : On
DNIe Demo : Off
My Colour Control
Energy Saving : S tandard
PIP
Move Enter Return
Picture
Off
On
3 Press the ENTER () button.
4 Press the … or † button to select Digital NR.
Press the
ENTER () button.
5 Select Off or On by pressing the … or † button.
Press the
ENTER () button.
English - 40
Page 41
Preventing Screen Burn-in
To reduce the possibility of screen burn, this unit is equipped with
screen burn prevention technology. This technology enables you to
set picture movement up/down (Vertical Line) and side to side
(Horizontal Dot). The Time setting allows you to program the time
between movement of the picture in minutes.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Setup.
Result
: The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Screen Burn Protection.
Press the
Result
5 Press the ENTER () button again.
Result
6 Press the ENTER () button.
Select
move per regular hour and preventing the residual image.
Press the
➢
7 Select the required option (Horizontal Dot, Vertical Line, or
Time) by pressing the … or † button.
Press the
ENTER () button.
: The Screen Burn Protection menu is displayed with
the
Pixel Shift selected.
: The Pixel Shift menu is selected.
On by pressing the … or † button for making the screen
ENTER () button.
Pixel Shift: Using this function, you can minutely move
pixels on the PDP in horizontal or vertical direction to
minimize after image on the screen.
ENTER () button.
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
TV
TV
Screen Burn Protection
Pixel Shift
All White
Signal Pattern
Move Enter Return
Pixel Shift : On
Horizontal Dot : 4
Vertical Line : 4
Time : 4
Move Enter Return
Setup
: Off
Pixel Shift
Off
On
8 Press the … or † button until you reach the optimal setting.
Press the
➢
ENTER () button.
Optimum condition for pixel shift;
Horizontal Dot
Vertical Line
Time
2
4
4
English - 41
Page 42
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
TV
Pixel Shift
All White
Signal Pattern
Move Enter Return
TV
Pixel Shift
All White
Signal Pattern
Reducing the Effects of Screen Burn
If screen burn has occurred, you can select a white screen or signal
Setup
: Off
Screen Burn Protection
Screen Burn Protection
pattern (rolling screen) to help remove screen burn artifacts.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Setup.
Result
: The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Screen Burn Protection.
Press the
Result
ENTER () button.
: The Screen Burn Protection menu is displayed.
5 Press the … or † button to select the option (All White or
Signal Pattern). Press the ENTER () button.
All White: This function helps remove after images on the
➢
screen by changing the colour of pixels to white. Use this
function when there are remaining after images or symbols
on the screen especially when you displayed a still image
on the screen for a long time.
Signal Pattern: This function helps remove after images
➢
on the screen by moving all the pixels on the PDP according
to a pattern. Use this function when there are remaining
after images or symbols on the screen especially when you
displayed a still image on the screen for a long time.
Move Enter Return
6 Press the ENTER () button to cancel the currently selected
function.
To remove after images on the screen, use either “All White” or
➢
“
Signal Pattern” function.
Although both of the two functions remove after images on the
screen, “
The after image removal function has to be executed for a long
➢
time (approximately 1 hour) to effectively remove after images on
the screen.
If after image is not improved after the execution of the function,
repeat the function again.
Signal Pattern” is more effective.
English - 42
Page 43
Changing the Sound Standard
You can select the type of special sound effect to be used when
watching a given broadcast.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the ▲ or ▼ button to select Sound.
Result
: The Sound menu is displayed.
3 Press the ENTER () button.
Result
: The Mode is selected.
4 Press the ENTER () button again.
5 Select the required option by pressing the ▲ or ▼ button.
Result
: The following options are available.
Standard - Music - Movie - Speech - Custom
6 Press the ENTER () button.
TV
Mode : Custom
Equalizer
SRS TSXT : Off
Auto Volume : Off
Internal Mute : Off
Move Enter Return
TV
Mode : Standard
Equalizer
SRS TSXT : Off
Auto Volume : Off
Internal Mute : Off
Move Enter Return
Sound
Sound
Standard
Music
Movie
Speech
Custom
You can select these options by simply pressing the
➢
S.MODE (Sound Mode) button on the remote control.
Custom
English - 43
Page 44
TV
Mode : Custom
Equalizer
SRS TSXT : Off
Auto Volume : Off
Internal Mute : Off
Move Enter Return
Customizing the Sound Settings
Your television has several settings which allow you to control the
Sound
sound quality.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Sound.
Result
:
The
Sound menu is
3 Press the ENTER () button.
displayed.
TV
R
L
Balance
Move Adjust Return
TV
Mode : Custom
Equalizer
SRS TSXT : Off
Auto Volume : Off
Internal Mute : Off
Move Enter Return
Equalizer
+
0
-
100Hz 300Hz 1kHz 3kHz 10kHz
+
0
-
4 Press the … or † button to select Equalizer.
Press the
Result
ENTER () button.
:
The
Equalizer menu is
5 Select the required option (balance or equalizer) by pressing the
œ or √ button.
6 Press the … or † button until you reach the
Press the
➢
ENTER () button.
If you make any changes to the sound settings, the sound
standard is automatically switched to
Adjusting the Volume Automatically
Each broadcasting station has its own signal conditions, and so it
Sound
is not easy for you to adjust the volume every time the channel is
changed. This feature lets you automatically adjust the volume of
the desired channel by lowering the sound output when the
modulation signal is high or by raising the sound output when
the modulation signal is low.
1 Press the MENU ()button.
Result
: The main menu is displayed.
displayed.
optimal
Custom.
setting.
TV
Mode : Custom
Equalizer
SRS TSXT : Off
Auto Volume : Off
Internal Mute : Off
Move Enter Return
English - 44
Sound
Off
On
2 Press the … or † button to select Sound.
Result
: The Sound menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Auto Volume.
Press the
ENTER () button.
5 Select Off or On by pressing the … or † button.
Press the
ENTER () button.
Page 45
Setting the TruSurround XT
TruSurround XT is a patented SRS technology that solves the
problem of playing 5.1 multichannel content over two speakers.
TruSurround delivers a compelling, virtual surround sound
experience through any two-speaker playback system, including
internal television speakers. It is fully compatible with all
multichannel formats.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Sound.
Result
:
The
Sound menu is
3 Press the ENTER () button.
4 Press the … or † button to select SRS TSXT.
Press the ENTER () button.
5 Select the required option by pressing the … or † button.
Result
: The following options are available.
Off - 3D Mono - Stereo
6 Press the ENTER () button.
displayed.
TV
Mode : Custom
Equalizer
SRS TSXT : Off
Auto Volume : Off
Internal Mute : Off
Move Enter Return
TV
Mode : Custom
Equalizer
SRS TSXT : Off
Auto Volume : Off
Internal Mute : Off
Move Enter Return
Sound
Sound
Off
3D Mono
Stereo
You can select these options simply by pressing the
➢
SRS () button on the remote control.
TruSurround XT, SRS and Symbol
➢
are trademarks of SRS Labs, Inc.
TruSurround XT technology is
incorporated under license from
SRS Labs, Inc.
English - 45
Page 46
TV
Mode : Custom
Equalizer
SRS TSXT : Off
Auto Volume : Off
Internal Mute : Off
Move Enter Return
Selecting the Internal Mute
If you want to hear the sound through separate speakers,
Sound
cancel the internal amplifier.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Sound.
Result
:
The
Sound menu is
3 Press the ENTER () button.
displayed.
TV
Mode : Custom
Equalizer
SRS TSXT : Off
Auto Volume : Off
Internal Mute : Off
Move Enter Return
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
Sound
4 Press the … or † button to select Internal Mute.
Press the
ENTER () button.
5 Select Off or On by pressing the … or † button.
Off
On
Press the
ENTER () button.
Setting the Melody Sound
You can hear melody sound when the television is powered on or
Setup
: Off
Setup
: Off
Off
On
off.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Setup.
Result
: The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Melody.
Press the
ENTER () button.
5 Select Off or On by pressing the … or † button.
Press the
ENTER () button.
English - 46
Page 47
Selecting the Sound Mode (depending on the model)
The “DUAL I-II” button displays/controls the processing and output
of the audio signal. When power is switched on, the mode is
automatically preset to either “DUAL-I ” or “Stereo”, depending on
the current transmission.
Type of broadcast
Regular broadcast
(Standard audio)
Regular +
NICAM
Stereo
A2
Stereo
◆ If the receiving conditions deteriorate, listening will be
➢
◆ If the stereo signal is weak and automatic switching
◆ When receiving mono sound in AV mode, connect to the
NICAM Mono
NICAM stereo
NICAM DUAL-I/II
Regular broadcast
(Standard audio)
Bilingual or DUAL-I/II
Stereo
easier if the mode is set to
occurs, switch to
“AUDIO-L” input connector on the panel (front or side,
depending on the model). If mono sound only comes out
of the left speaker, press the
Mono.
On-screen indication
(Normal use)
Mono
NICAM Mono↔Mono
NICAM stereo↔Mono
NICAM DUAL-I
NICAM DUAL-II
Mono
Mono
DUAL-
I↔DUAL-II
Stereo↔Mono
Mono.
DUAL I-II button.
(Forced mono)
→
→
(Forced mono)
English - 47
Page 48
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
Setting and Displaying the Current Time
You can set the television’s clock so that the current time is displayed
Setup
: Off
by pressing the “INFO ( )” button. You must also set the time if
you wish to use the automatic on or off timers.
When pressing the power button (On/Off) on the panel of
➢
the television, the clock setting will be reset.
1 Press the MENU () button.
Result
: The main menu is displayed.
TV
Clock Set 12 : 00
Sleep Timer :Off
On Timer 00 : 00 Off
Off Timer 00 : 00 Off
Move Enter Return
TV
Hour
12 00
Move Adjust Return
Time
Clock Set
Minute
2 Press the … or † button to select Setup.
Result
: The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Time.
Press the
Result
ENTER () button.
: The Clock Set is selected.
5 Press the ENTER () button again.
6 Press the œ or √ button to select Hour or Minute.
Set these by pressing the
You can also set these by pressing the numeric buttons
➢
directly.
… or † button.
7 Press the ENTER () button.
In the event of a power interuption or the set being turned
➢
off at the supply, the settings for the Clock will be lost.
English - 48
Page 49
Setting the Sleep Timer
You can select a time period of between 30 and 180 minutes after
which the television automatically switches to Standby mode.
1 Press the MENU () button.
Result
: The main menu is displayed.
2 Press the … or † button to select Setup.
Result
: The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Time.
Press the
Result
5 Press the … or † button to select Sleep Timer.
Press the
ENTER () button.
: The Time menu is displayed.
ENTER () button.
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
TV
Clock Set 12 : 00
Sleep Timer :Off
On Timer 00 : 00 Off
Off Timer 00 : 00 Off
Setup
: Off
Time
6 Select the preset time interval (Off, 30 , 60 , 90, 120, 150, or 180)
for staying on by pressing the
Press the
➢
ENTER () button.
◆
You can select these options simply by pressing the
SLEEP button on the remote control.
◆
If the sleep timer is not yet set,
If the sleep timer is already set, the remaining time
before which the television switches to standby mode
is displayed.
▲ or ▼ button.
Off
is displayed.
Move Enter Return
TV
Clock Set : 00 : 00
Sleep Timer :Off
On Timer : 00 : 00 Off
Off Timer : 00 : 00 Off
Move Enter Return
Sleep Timer : Off
Time
Off
30
60
90
120
150
180
English - 49
Page 50
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
Switching the Television On and Off Automatically
You can set the on or off timers so that the television will:
Setup
: Off
◆ Switch on automatically and tune to the channel of your
choice at the time you select.
◆ Switch off automatically at the time you select.
The first step is to set the television’s clock (refer to
➢
“Setting and Displaying the Current Time” on page 48).
1 Press the MENU () button.
Result
: The main menu is displayed.
TV
Clock Set 12 : 00
Sleep Timer :Off
On Timer 00 : 00 Off
Off Timer 00 : 00 Off
Move Enter Return
TV
Hour
00
Programme
01
Volume Activation
10 No
Move Adjust Return
TV
Hour
00
Programme
01
Volume Activation
10 Yes
Move Adjust Return
Time
On Timer
Minute
On Timer
Minute
2 Press the … or † button to select Setup.
Result
:The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Time.
Press the
Result
ENTER () button.
: The Time menu is displayed.
5 Press the … or † button to select On Timer.
Press the
Result
00
ENTER () button.
: The On Timer menu is displayed.
6 Select Hour, Minute , Programme, or Volume by pressing the œ or √
button.
Set these by pressing the
You can also set these by pressing the numeric buttons
➢
… or † button.
directly.
7 Press the œ or √ button to select Activation.
8 To activate On Timer with the setting entered, select Yes by
00
pressing the
… or † button.
9 Press the ENTER () button.
Result
: The Time menu is displayed again.
English - 50
Page 51
Switching the Television On and Off Automatically
(continued)
10 Press the … or † button to select Off Timer.
Press the
Result
ENTER () button.
: The Off Timer menu is displayed.
11 Select Hour or Minute by pressing the œ or √ button.
Set these by pressing the
You can also set these by pressing the numeric buttons
➢
directly.
… or † button.
12 Press the œ or √ button to select Activation.
13 To activate Off Timer with the setting entered, select Yes by
pressing the
… or † button.
14 Press the ENTER () button.
Auto Power Off
➢
When you set the timer “On”, the television will
eventually turn off, if no controls are operated for 3 hours
after the TV was turned on by timer. This function is only
available in timer “On” mode and prevents overheating or
leakages, which may occur if a TV is on for too long (when
you are on vacation, for example).
If no signal is received for 15 minutes, the TV will be
➢
automatically turned off.
TV
Clock Set 12 : 00
Sleep Timer :Off
On Timer 06 : 00 On
Off Timer 00 : 00 Off
Move Enter Return
TV
Hour
07 No00
Move Adjust Return
TV
Hour
07 Yes00
Time
Off Timer
Minute Activation
Off Timer
Minute Activation
Move Adjust Return
English - 51
Page 52
TV
Source List : TV
Edit Name
Viewing an External Signal Source
Use the remote control to switch between viewing signal from
Input
Move Enter Return
connected equipment, such as VCR, DVD, Set-Top box, and the TV
source (broadcast or cable).
1 Press the MENU () button.
Result
: The main menu is displayed.
2 Press the ENTER () button to select Input.
Result
: The Input menu is displayed.
TV
TV
Ext.1 :
Ext.2 :
AV :
S-Video :
Component :
PC :
TV
Source List : TV
Edit Name
TV
Ext.1 :
Ext.2 :
AV :
S-Video :
Component :
PC :
Source List
----
----
----
----
----
----
Move Enter Return
Input
Move Enter Return
Edit Name
----
----
----
VCR
----
DVD
----
D-VHS
----
Cable STB
----
Move Enter Return
3 Press the ENTER () button.
Result
: The Source List is selected.
4 Press the ENTER () button agian.
5 Press the … or † button to select the signal source, press the
ENTER () button.
Result
: The available signal sources are listed.
◆
➢
TV, Ext.1 , Ext.2, AV , S-Video, Component, or PC
: on the TV’s rear panel.
◆
You can also set these options simply by pressing the
SOURCE () button on the remote control.
6 Press the MENU () button.
Result
: The main menu is displayed.
7 Press the ENTER () button to select Input.
Result
: The Input menu is displayed agian.
8 Press the … or † button to select Edit Name.
Press the
ENTER () button.
9 Press the … or † button to select external source to be edited.
Press the
Result
ENTER () button.
: The available device names are listed.
VCR, DVD , D-VHS, Cable STB, HD STB, Satellite
STB
, AV Receiver, DVD Receiver, Game, Camcorder,
DVD Combo, DHR (DVD HDD Recorder), or PC
10 Select the required device by pressing the … or † button.
Press the
ENTER () button.
English - 52
If you change the external source while viewing, pictures
➢
might take a short period of time to switch.
Page 53
Redirecting an Input to the External Output
Your television enables you to choose which audio/video signals
are output to the external connector.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Setup.
Result
: The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select AV Setup.
Press the
Result
5 Press the … or † button to select required input (Ext.2). Press
the
output by pressing the
➢
ENTER () button.
: The AV Setup menu is displayed.
ENTER () button. Select the source to be directed to the
… or † button.
◆
Ext.1 : Default (TV )
◆
Ext.2 : Variable (TV , Ext.1, Ext.2, AV,
S-Video, or Monitor Out)
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : Off
Colour Weakness
More
Move Enter Return
TV
Ext.1 : TV
Ext.2 : TV
Move Enter Return
Setup
: Off
AV Setup
6 Press the ENTER () button.
English - 53
Page 54
Teletext Feature
Most television channels provide written information services via
teletext. Information provided includes:
The teletext pages are organized according to six categories:
◆
Television programme times
◆
News bulletins and weather forecasts
◆
Sports results
◆
Travel information
Part Contents
A Selected page number.
B Broadcasting channel identity.
C Current page number or search indications.
D Date and time.
EText.
F Status information.
FASTEXT information.
Teletext information is often divided between several pages
➢
displayed in sequence, which can be accessed by:
◆ Entering the page number
◆ Selecting a title in a list
◆ Selecting a coloured heading (FASTEXT system)
English - 54
Page 55
Displaying the Teletext Information
You can display Teletext information at any time on your television.
For Teletext information to be displayed correctly,
☛
channel reception must be stable; otherwise:
◆ Information may be missing
◆ Some pages may not be displayed
1 Select the channel providing the Teletext service by pressing the
P or button.
2 Press the TTX/MIX () button to activate the teletext mode.
Result
:
The contents page is displayed. It can be redisplayed at
any time by pressing the (index) button.
3 Press the TTX/MIX () button again.
Result
:
The screen will be split into two. This Double Teletext
feature lets you view the
information separately on the screen.
4 If you wish to display the actual broadcast and teletext information
on a single screen, press the
5 Press the EXIT/TV button to exit from the teletext display.
actual broadcast
TTX/MIX ()button again.
and teletext
English - 55
Page 56
Selecting Display Options
When you have displayed a Teletext page, you can select various
options to suit your requirements.
To display... Press the...
◆ Hidden text (reveal)
(answers to quiz games, for example)
◆ The normal screen (reveal) again
◆ A secondary page (sub-page)
◆ The broadcast when searching for a page (cancel)
◆ The next page (page up)
◆ The previous page (page down)
◆ Double-size letters in the: (size)
• Upper half of the screen • Once
• Lower half of the screen • Twice
◆ Normal screen • Three times
To return to the normal display after using the reveal or
➢
size feature, press the
EXIT/TV
button.
English - 56
Page 57
Selecting a Teletext Page
You can enter the page number directly by pressing the numeric
buttons on the remote control.
1 Enter the three-digit page number given in the content by
pressing the corresponding numeric buttons.
Result
: The current page counter is incremented and the page
is then displayed. If the selected page is linked with
several secondary pages, the secondary pages are
displayed in sequence. To freeze the display on a
given page, press the (hold). Press it again to
resume.
2 If the FASTEXT system is used by a broadcasting company, the
different topics covered on a Teletext page are colour-coded and
can be selected by pressing the coloured buttons on the remote
control.
Press the coloured button corresponding to the topic that you wish
to select; the available topics are given in the status line.
Result
: The page is displayed with other coloured information
that can be selected in the same way.
3 To display the previous or next page, press the corresponding
coloured button.
4 To display the sub-page, see the following steps.
◆
Press the (sub-page) button.
Result
: The available sub-pages appear.
◆
Select the required sub-page. Sub-pages can be scrolled by
pressing the or button.
5 When you have finished, press the EXIT/TV button to return to
your normal broadcast.
English - 57
Page 58
Connecting to External Input/Output
“EXT 1” is used for the equipment with an RGB output, such as video game devices or video disc players.
①
Rear of the TV
or
②
VCR
③
or
Video Game Device
①
This end can be fitted with:
◆ A SCART connector
◆ An S-Video connector and two audio RCA connectors (L+R); EXT 2
◆ Three RCA connectors (VIDEO + AUDIO-L and R)
②
If you have a second VCR and wish to copy cassette tapes, connect the
source VCR to
redirect the signal from
③
If you have a decoder, connect the decoder to the VCR and the VCR to
the television.
➃
When you wish to record a programme, connect the receiver to EXT 1 and
the VCR to
Please be sure to match the colour coded input terminals and cable jacks.
➢
Input/Output Specification
Connector
EXT 1 ✔✔ ✔✔ Only TV output is available.
EXT 2 ✔✔ ✔ Output you can choose.
EXT 1 and the target VCR to EXT 2 so that you can
EXT 1 to EXT 2.
EXT 2 so that you can redirect the signal from EXT 1 to EXT 2.
Input Output
Video Audio (L/R) S-Video RGB Video + Audio (L/R)
④
DVD
Decoder /
Video Disc Player
Satellite Receiver
English - 58
Whenever you connect an audio or video system to your
☛
television, ensure that all
Refer to the documentation supplied with your equipment
for detailed connection instructions and associated safety
precautions.
elements are switched off.
Page 59
Connecting to the AV Output
“AV OUT” are used for the equipment with an RGB output, such as video game devices or video disc players.
Rear of the TV
①
This end can be fitted with:
◆ Three RCA connectors (VIDEO + AUDIO L/R)
②
If you have a second VCR and wish to copy cassette tapes, connect the
source VCR to
redirect the signal from
③
When you wish to record a programme, connect the receiver to
and the VCR to “AV OUT” so that you can redirect the signal from “AV IN”
to “AV OUT”.
Please be sure to match the colour coded input terminals and cable jacks.
➢
“
AV IN” and the target VCR to “AV OUT” so that you can
“
AV IN” to “AV OUT”.
“
AV IN”
①
VCR
②
DVD
Decoder /
Video Game Device
Video Disc Player
Satellite Receiver
③
English - 59
Page 60
Connecting to the RCA Input
➢ The RCA (VIDEO + AUDIO L /R) connectors are used for equipment, such as camcorders, video disc
players, and some video game devices.
Camcorder
Rear of the TV
Video game device
Video disc player
Please be sure to match the colour coded input terminals and cable jacks.
➢
Connecting to the S-Video Input
➢ The S-VIDEO and AUDIO L /R connectors are used for equipment with an S-Video output, such as a
camcorder or VCR.
Camcorder
Rear of the TV
and
①
To play pictures and sound, both the S-VIDEO and AUDIO L /R connectors must be used.
Please be sure to match the colour coded input terminals and cable jacks.
➢
①
VCR
English - 60
Whenever you connect an audio or video system to your television,
☛
ensure that all elements are switched off. Refer to the documentation
supplied with your equipment for detailed connection instructions
and associated safety precautions.
Page 61
Connecting to the Component Input
Rear of the TV
The COMPONENT IN connectors are used
for equipment with a DVD or DTV receiver
output.
(480i/480p/576i/576p/1080i)
①
DVD
DTV receiver
②
Please be sure to match the colour coded input terminals and cable jacks.
➢
English - 61
Page 62
Connecting to the PC Input
The “PC IN” (video) and “AUDIO” connectors are used for interfacing with your PC.
➢
Rear of the TV
Personal Computer
and
English - 62
Page 63
Connecting Home Theater System
Use the “AV OUT” ports of the PDP for Home Theater System Connections.
Rear of the TV
Connecting the Home Theater System
①
Connect the monitoring audio out L and
R jacks of the
connection panel of the PDP TV to the
AUDIO IN jacks of the DVD Home
Theater System (or AV Receiver) using
the audio cable.
②
Press the SOURCE ()button to
select the desired external device
connected to the PDP TV.
③
If you want to hear the sound through
separate speakers, cancel the internal
amplifier.
AV OUT on the rear-side
①
DVD Home Theater
Please be sure to match the colour coded input terminals and cable jacks.
➢
◆ Refer to corresponding user’s manual from the manufacturer for wiring the
☛
To Display the DVD Home Theater
!
Turn the PDP on and press the SOURCE ()button to select the Ext.1, Ext.2, or Component.
@
Be sure to connect the video cable properly if desired external input (Ext.1, Ext.2, or Component)
cannot be selected.
#
Play the DVD after activating the DVD Home Theater System.
$
Use the volume control of the Home Theater System while watching the PDP using the DVD
Home Theater, where the PDP TV does not produce the audio.
speakers to the DVD Home Theater System (or AV Receiver).
◆ Disable the PDP TV internal speaker to enjoy the rich sound through the
speakers of your Home Theater System.
②
AV Receiver Amplifier
English - 63
Page 64
Setting up Your PC Software (Windows only)
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card. But even if your actual screens look different, the same, basic set-up information will apply
in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1 Right click the mouse on the Windows Desktop,
then click on
The
Display Properties will be displayed.
2 Click on Settings tab, then set the Display Mode
with reference to the Display Modes Table.
You do not need to change the Colours settings.
Properties.
3 Click on Advanced. A new settings dialog box
will be displayed.
2
3
4 Click on the Monitor tab, then set the Screen
refresh rate
Table. Set the Vertical Frequency and Horizontal
Frequency individually if you can do so instead of
setting the
with reference to the Display Modes
Screen refresh rate.
5 Click on OK to close the window, then Click on
OK button to the Display Properties window.
Automatic re-booting may commence at this
moment.
6 Shutdown the PC, and connect it to your TV.
(“Connecting to the PC Input” on page 62)
◆
4
➢
5
The actual screens on your PC may look
different, depending on your particular
version of Windows and the type of your
PC.
◆
When you use your TV as a PC monitor, it
supports Colours up to 32 bits.
◆
In this case, the display on the TV may look
different depending on your particular
version of Windows or the PC
manufacturer.
◆
When connecting a PC you must set it to
the display settings that are supported by
the TV. Otherwise, the message
input range
will be displayed.
Out of
English - 64
Page 65
Input Mode (PC)
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
Video Signal
IBM PC / AT
Compatible
◆ The interlace mode is not supported.
◆ The television might operate abnormally if a non-standard video format is selected.
◆ 480i/p, 576i/p, 720p, or 1080i is not available in pc mode.
Resolution
(Dot X Line)
640 x 350
720 x 400
640 x 480
800 x 600
848 x 480
1024 x 768
Vertical
frequency (Hz)
70.086
70.087
59.940
70.000
72.809
75.000
56.250
60.317
70.000
72.188
75.000
60.000
74.769
60.004
70.069
72.000
75.029
Horizontal
frequency (kHz)
31.469
31.469
31.469
35.000
37.861
37.500
35.156
37.879
43.750
48.077
46.875
31.020
37.684
48.363
56.476
57.672
60.023
Vertical
polarity
P
N
N
N/P
N
N
N/P
P
N/P
P
P
P
P
N
N
N/P
P
(N: Negative / P: Positive)
Notes
Horizontal
polarity
N
P
N
N/P
N
N
N/P
P
N/P
P
P
P
N
N
N
N/P
P
◆ The PC text quality is optimum in WVGA mode (848 x 480@60Hz).
◆ When this television is used as a PC display, 32-bit colour is supported.
◆ Your PC display screen might appear different depending on the manufacturer (and your particular version of
Windows). Check your PC instruction book for information about connecting your PC to a television.
◆ If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5kHz (horizontal).
In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned
off (or if the PC is disconnected). If so, press the
sure that the PC is connected.
◆ When connecting a notebook PC to the television, make sure that the PC screen is displayed through only the
television (Otherwise, random signals might appear).
◆ When horizontal synchronous signals seem irregular in PC mode, check PC power saving mode or cable
connections.
◆ The Display Settings Table above complies to the IBM/VESA standards, and based on the analog input.
◆ The best timing for the vertical frequency to each mode is 60Hz.
SOURCE ()button to enter the Video mode. Also, make
English - 65
Page 66
Troubleshooting: Before Contacting Service Personnel
Before contacting Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the
television and contact your local dealer.
No sound or picture
Normal picture but no sound
No picture or black and white picture
Sound and picture interference
Blurred or snowy picture,
distorted sound
Remote control malfunctions
Screen is black and power indicator
light blinks steadily
◆ Check that the mains lead has been connected to a wall socket.
◆ Check that you have pressed the power button (On/Off) and the
POWER () button.
◆ Check the picture contrast and brightness settings.
◆ Check the volume.
◆ Check the volume.
◆ Check whether the volume MUTE () button on the remote control
has been pressed.
◆ Adjust the colour settings.
◆ Check that the broadcast system selected is correct.
◆ Try to identify the electrical appliance that is affecting the television,
then move it further away.
◆ Plug your television into a different mains socket.
◆ Check the direction, location and connections of your aerial.
This interference often occurs due to the use of an indoor aerial.
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check the battery terminals.
◆ On your computer check; Power, Signal Cable.
◆ The TV is using its power management system.
◆ Move the computer’s mouse or press any key on the keyboard.
◆ On your equipment check (STB, DVD, etc) ; Power, Signal Cable.
◆ The TV is using its power management system.
◆ Press the Source button on the panel or remote control.
◆ Turn the TV off and on.
English - 66
Page 67
Memo
English - 67
Page 68
-
AFTER SALES SERVICE
-
Do not hesitate to contact your retailer or service agent
if a change in the performance of your product indicates
that a faulty condition may be present.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European
countries with separate collection systems)
This marking shown on the product or its literature,
indicates that it should not be disposed with other
household wastes at the end of its working life. To prevent possible harm
to the environment or human health from uncontrolled waste disposal,
please separate this from other types of wastes and recycle it responsibly
to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased
this product, or their local government office, for details of where and
how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed
with other commercial wastes for disposal.
BN68-00867B-01
Loading...