Samsung PNM-9000VD, SLA-5M3700D, SLA-5M4600D, SLA-5M7000D User Manual

NETWORK CAMERA

User Manual

PNM-9000VD

SLA-5M3700D/SLA-5M4600D/SLA-5M7000D

Network Camera

User Manual

Hanwha Techwin

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.

Disclaimer

Hanwha Techwin

provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. right to change the contents of this document without prior notice.

Design and specications are subject to change without prior notice.

The initial administrator ID is “admin” and the password should be set when logging in for the rst time.

Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be

Co., Ltd. All r ights reser ved.

Hanwha Techwin

reserves the

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.

(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.)

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from / PoE(48V), 0.27A. (PNM-9000VD)

16. This Lens module has to be connected with equipment, which supplied by a power supply unit marked “Class 2” or “LPS”. (SLA-5M3700D/5M4600D/5M7000D)

17. This product is intended to be supplied by isolation power.

18. If you use excessive force when installing the product, the camera may be damaged and malfunction.

If you forcibly install the product using non-compliant tools, the product may be damaged.

19. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or near the kitchen table. This may cause damage to the product.

20. When installing the product, be careful not to allow the surface of the product to be stained with chemical substance. Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface.

21. If you install/disassemble the product in a manner that has not been recommended, the production functions/ performance may not be guaranteed. Install the product by referring to “Installation & connection” in the user manual.

22. Installing or using the product in water can cause serious damage to the product.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

●● OVERVIEW

English _3

overview

Class construction

An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

ATTENTION

IL Y A RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE TYPE INCORRECT. METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

The CVBS out terminal of the product is provided for easier installation, and is not recommended for monitoring purposes.

Please use the input power with just one camera and other devices must not be connected.

The ITE is to be connected only to PoE networks without routing to the outside plant.

The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3af shall be a UL Listed device with the output evaluated as a Limited Power Source as defined in UL60950-1.

Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102. As such, associated Ethernet wiring shall be limited to inside the building.

Please read the following recommended safety precautions carefully.

yDo not place this apparatus on an uneven surface. yDo not install on a surface where it is exposed to direct sunlight, near heating equipment or

heavy cold area. yDo not place this apparatus near conductive material. yDo not attempt to service this apparatus yourself. yDo not place a glass of water on the product. yDo not install near any magnetic sources. yDo not block any ventilation openings. yDo not place heavy items on the product. yPlease wear protective gloves when installing/removing the camera.

The high temperature of the product surface may cause a burn.

User’s Manual is a guidance book for how to use the products. The meaning of the symbols are shown below.

yReference : In case of providing information for helping of product’s usages yNotice : If there’s any possibility to occur any damages for the goods and human caused by

not following the instruction

 Please read this manual for the safety before using of goods and keep it in the safe place.

4_ overview

CONTENTS

OVERVIEW

INSTALLATION & CONNECTION

NETWORK CONNECTION AND

SETUP

3 Important Safety Instructions 6 Product Features 6 Recommended PC Specifications 6 Recommended Micro SD/SDHC/SDXC

Memory Card Specifications

7 What’s Included (PNM-9000VD) 7 What’s Included (Lens module -optional) 8 At a Glance (PNM-9000VD) 9 At a Glance (Lens module)

10 Installation 12 How to install LAN cable for different

installation locations

13 Inserting/Removing a Micro SD Memory

Card

14 Connecting with other Device

15 Connecting the Camera Directly to Local

Area Networking

15 Connecting the Camera Directly to a DHCP

Based DSL/Cable Modem

16 Buttons used in IP Installer 16 Static IP Setup 18 Dynamic IP Setup 18 Port Range Forward (Port Mapping) Setup 19 Connecting to the Camera from a Shared

Local PC

19 Connecting to the Camera from a Remote

PC via the Internet

WEB VIEWER

APPENDIX

20 Connecting to the Camera 21 Password setting 21 Login 21 Camera Web Viewer Setup

22 Specification (PNM-9000VD) 23 Specification (Lens module) 24 Product Overview 25 Troubleshooting 26 Open Source Announcement

●● OVERVIEW

English _5

overview

PRODUCT FEATURES

• Lens options according to focal length You can select the lens you want and attach it to the camera.

• Dustproof/Waterproof (IP66) The dustproof and waterproof design makes you feel at ease when installing the product outdoors or exposing

it to rain.

• Multi-Streaming This network camera can display videos in different resolutions and qualities simultaneously using different

CODECs.

• Web Browser-based Monitoring Using the Internet web browser to display the image in a local network environment.

• Alarm When an event occurs, related videos are sent to the user’s registered e-mail and FTP server or stored on the Micro

SD memory card.

• Tampering Detection Detects tempering attempts on video monitoring.

• Defocus detection function Detects the defocus phenomenon of the camera lens.

• Motion Detection Detects motion from the camera’s video input.

• Fog detection Detects fog that is heavier than the detection level.

• Face Detection Detects faces in the specified area from the camera’s video input.

• IVA (Intelligent Video Analysis) function Detects a motion or situation that meets the configured event rules.

• Auto Detection of Disconnected Network Detects network disconnection before triggering an event.

• ONVIF Compliance This product supports ONVIF Profile S.

For more information, refer to www.onvif.org.

RECOMMENDED PC SPECIFICATIONS

• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher

• Supported OS : Windows 7, 8.1, 10, Mac OS X 10.12, 10.13, 10.14

• Recommended Browser: Google Chrome

• Supported web browsers : MS Explore11, MS Edge, Mozilla Firefox(Window 64bit only), Apple Safari(Mac OS X only)

RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS

• Recommended capacity : 16GB to 256GB (MLC type)

• The following types of memory cards from the following manufacturers are recommended for this camera.

- Manufacturer : SanDisk, Transcend

- Product family : High endurance

• It is recommended to use a memory card of 16GB or more that conforms to the UHS-3 class (MLC type) specification.

6_ overview

WHAT’S INCLUDED (PNM-9000VD)

Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.)

Appearance Item Name Quantity Description

Camera 1

Instruction book, Installer S/W CD

Appearance Item Name Quantity Description

Cap Installer 1 Used to connect the RJ45 cable.

●● OVERVIEW

Card-type moisture absorbent 1 Attached when installed.

WHAT’S INCLUDED (LENS MODULE -OPTIONAL)

Appearance Item Name Quantity Description Model Name

Quick Guide

(Optional)

Warranty card

(Optional)

Cable for the testing monitor 1

Template 1 Product installation guide

Star-shaped wrench 1 To remove/fix the cover top

Tapping Screw 4 Used for installation on the wall or ceiling

Plastic Anchor 4

Machine Screws 4

Cable bush 2

Used to test the camera connection to a portable

display device

For fixing a screw, Inserted in a hole

(reinforced anchoring force)

Used for assembling the dome case when installing

the product on the pipe, wall mount, etc. or blocking a

hole.

Used to connect the LAN cable with a diameter of

Ø7~8.5.

Lens module

Mounted to PNM-9000VD

SLA-5M3700D

SLA-5M4600D

SLA-5M7000D

English _7

overview

AT A GLANCE (PNM-9000VD)

Appearance

Item Description

Cover top

Case cover used to protect the lens and the main unit.

Inside

Camera fixing screws

Lens module mounting

portion

Reset Button

g f

Item Description

Screws that fix the camera body to the mounting plate.

This is the terminal to mount the lens module.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that DHCP can be

enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

c d

8_ overview

Test Monitor Out

Micro SD Memory Card

Compartment

Power On/Off switch

Lens module indication light (normal: green, abnormal:

red)

Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.

Compartment for the Micro SD memory card.

Switch used to turn the product On/off.

Use it only to replace your lens module.

If the lens module is attached correctly, the green LED will illuminate and then turn off after approximately 40 seconds. (to prevent undesirable reflections)

AT A GLANCE (LENS MODULE)

Appearance

Item Description

●● OVERVIEW

Lens module

Camera connector

This is a lens module that records video.

This is a terminal to connect with the camera.

English _9

installation & connection

INSTALLATION

This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are

recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• Select an installation site that can hold at least 5 times the camera’s weight.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

• If the product is installed with excessive force, it may cause damage to the camera due to malfunction. Forcing assembly using non-compliant tools may damage the product.

• Do not remove the lens module while the power is on.

Disassembling

Remove the cover top by unscrewing the four screws in a counterclockwise direction using the supplied star-shaped wrench.

Note that it is not necessary to loosen the screws completely.

Mounting lens module

1. Align and fasten the connector of the lens module with

the connector of the camera body.

You are recommended to avoid touching the lens separately,

as it is shipped from the factory with the focus adjusted during the manufacturing inspection.

2. Complete the lens mounting process.

10_ installation & connection

Installation on a ceiling or wall

1. Use the provided template to drill holes for installation (diameter

6 mm and minimum depth 45mm) and insert the supplied plastic anchors to the end.

2. Align the moun.ting hole of the camera with the hole where the plastic anchor is inserted, then tighten the tapping screw.

3. Mount the camera body to the mount plate.

Mount it to fit the hinges as shown in the image.

4. Connect a cable to the camera. Be careful not to damage the cable. It should be trimmed up.

5. If the lens module is not attached correctly,

the lens module status light will illuminate red, as shown in the figure. If this occurs, turn off the power switch and reattach the lens module. If attached normally, it will illuminate green and then turn off after approximately 40 seconds.

6. Push it until it clicks into the fixing bracket as shown in the figure.

7. Use the camera fixing screws to fix the camera body to the

mounting plate.

●● INSTALLATION & CONNECTION

English _11

installation & connection

8. Cover the cover top and turn the screw clockwise using a star-shaped wrench to secure the cover.

If you do not tighten the screws completely when fixing the cover,

it may cause waterproofing problems. (IP66)

HOW TO INSTALL LAN CABLE FOR DIFFERENT INSTALLATION LOCATIONS

Directly installing on wall/ceiling

1. Pull the LAN cable out of the hole of the mounting plate.

Installing using pipe

1. Separate the pipe cover of the mount plate by pressing its sides.

2. Place the pipe on the mount plate.

3. Pull the LAN cable out of the hole of the mounting plate.

12_ installation & connection

+ 25 hidden pages