Samsung PND-9080R User Manual

NETWORK CAMERA

User Manual

PND-9080R/PNO-9080R/PNV-9080R

Network Camera

User Manual

Hanwha Techwin

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.

Disclaimer

Hanwha Techwin

provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. right to change the contents of this document without prior notice.

Design and specications are subject to change without prior notice.

The initial administrator ID is “admin” and the password should be set when logging in for the rst time.

Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be

Co., Ltd. All r ights reser ved.

Hanwha Techwin

reserves the

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and

the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated

from 24 Vac (50/60 Hz) 1.0 A or 12 Vdc, 1.0 A.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

●● OVERVIEW

English _3

overview

Class construction

An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.

CAUTION

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

The CVBS out terminal of the product is provided for easier installation, and is not recommended for monitoring purposes.

Please use the input power with just one camera and other devices must not be connected.

The ITE is to be connected only to PoE networks without routing to the outside plant.

Please read the following recommended safety precautions carefully.

yDo not place this apparatus on an uneven surface. yDo not install on a surface where it is exposed to direct sunlight, near heating equipment or

heavy cold area. yDo not place this apparatus near conductive material. yDo not attempt to service this apparatus yourself. yDo not place a glass of water on the product. yDo not install near any magnetic sources. yDo not block any ventilation openings. yDo not place heavy items on the product. yPlease wear protective gloves when installing/removing the camera.

The high temperature of the product surface may cause a burn.

User’s Manual is a guidance book for how to use the products.

The meaning of the symbols are shown below.

yReference : In case of providing information for helping of product’s usages yNotice : If there’s any possibility to occur any damages for the goods and human caused by

not following the instruction

 Please read this manual for the safety before using of goods and keep it in the safe place.

4_ overview

CONTENTS

overview

installation & connection

network connection and

setup

3 Important Safety Instructions 6 Product Features 6 Recommended PC Specifications 6 Recommended Micro SD/SDHC/SDXC

Memory Card Specifications

6 NAS recommended specs 7 What’s Included 8 At a Glance (PND-9080R) 10 At a Glance (PNO-9080R) 11 At a Glance (PNV-9080R)

13 Installation (PND-9080R) 14 Installation (PNO-9080R) 15 Installation (PNV-9080R) 18 Inserting/Removing a Micro SD Memory

Card

20 Memory Card Information (Not Included) 20 Connecting with other Device

24 Connecting the Camera Directly to Local

Area Networking

24 Connecting the Camera Directly to a DHCP

Based DSL/Cable Modem

25 Connecting the Camera Directly to a

PPPoE Modem

25 Connecting the Camera to a Broadband

Router with the PPPoE/Cable Modem

26 Buttons used in IP Installer 26 Static IP Setup 28 Dynamic IP Setup 28 Port Range Forward (Port Mapping) Setup 29 Connecting to the Camera from a Shared

Local PC

29 Connecting to the Camera from a Remote

PC via the Internet

web viewer

setup screen

appendix

30 Connecting to the Camera 31 Password setting 31 Login 31 Plug-in support specifications for each

browser

32 Installing WebViewer Plugin 32 Using a Plug-in Free Webviewer 32 Using the Live Screen (Plug-in Free

Webviewer)

34 Using the Live Screen (Plug-in Webviewer) 36 Playing the recorded video (Plug-in Free

Webviewer)

38 Playing the recorded video (Plug-in

Webviewer)

41 Setup 41 Basic Setup 45 Audio & Video setup 51 Network Setup 54 Event Setup 56 NAS (Network Attached Storage) guide 63 System Setup

66 Specification 68 Product Overview 70 Troubleshooting 71 Open Source Announcement

●● OVERVIEW

English _5

overview

PRODUCT FEATURES

• Dustproof/Waterproof (IP66) (PNO-9080R/PNV-9080R)

The dustproof and waterproof design makes you feel at ease when installing the product outdoors or exposing it to rain.

• IR mode

If the IR indicator turns on, the product switches to the IR mode for preventing an object from being too bright, which helps you identify the object in near distance.

• Supports 4K resolution videos

• Multi-Streaming

This network camera can display videos in different resolutions and qualities simultaneously using different CODECs.

• Web Browser-based Monitoring

Using the Internet web browser to display the image in a local network environment.

• Alarm

When an event occurs, video is either sent to the email address registered by the user, sent to the FTP server, saved in a Micro SD card or NAS, or a signal is sent to the alert output terminal.

• Tampering Detection

Detects tempering attempts on video monitoring.

• Defocus detection function

Detects the defocus phenomenon of the camera lens.

• Motion Detection

Detects motion from the camera’s video input.

• Intelligent Video Analysis

Analyzes video to detect logical events of specified conditions from the camera’s video input.

• Audio Detection

Detects sound louder than a certain level specified by user.

• Smart Codec

Adaptively applies codecs for a portion of the camera’s field of view to improve the quality of such area specified by user.

• Auto Detection of Disconnected Network

Detects network disconnection before triggering an event.

• ONVIF Compliance

This product supports ONVIF Profile S&G. For more information, refer to www.onvif.org.

RECOMMENDED PC SPECIFICATIONS

• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher

• Supported OS : Windows 7, 8.1, 10, Mac OS X 10.9, 10.10, 10.11

• Plug-in free web viewer

Supported web browsers : Google Chrome 47, MS Edge 20

• Plug-in Webviewer

Supported web browsers : MS Explorer 11, Mozilla Firefox 43, Apple Safari 9 ※ Mac OS X only

• VGA : To play a 4K (4096 x 2160) resolution video at 30fps, a GPU that supports 4096 x 2160 resolution and 4K/H.264 decoding is required

RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS

• Recommended capacity : 4GB ~ 128GB (uhs-1 class)

• For your camera, we recommend you use a memory card from the following manufacturers: Micro SD/SDHC/SDXC Memory Card : Sandisk, Transcend

• To save a 4K resolution video, it is recommended to use a uhs-3 class (MLC type) memory card with a storage space of 16GB or higher.

NAS RECOMMENDED SPECS

• Recommended capacity : 200GB or higher is recommended.

• Simultaneous access : One unit of NAS can accept a maximum of sixteen camera accesses.

• For this camera, you are recommended to use a NAS with the following manufacturer’s specs.

Recommended products Available sizes

Netgear NAS A maximum of 16 cameras can access simultaneously.

Synology NAS A maximum of 16 cameras can access simultaneously.

When you use Netgear’s NAS equipment, do not allocate the capacity for use.

If you use NAS equipment for purposes other than video saving, the number of accessible cameras may be reduced.

6_ overview

WHAT’S INCLUDED

RESET

Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.)

Appearance Item Name Quantity Description Model Name

PND-9080R

Appearance Item Name Quantity Description Model Name

L Wrench

Alarm cable

Used to control the direction of the

camera / Used to remove and replace

the dome cover

Used when connecting to an alarm PND-9080R

PNO-9080R/

PNV-9080R

●● OVERVIEW

Camera

Instruction book, Installer S/W CD

Quick Guide

(Optional)

Warranty card

(Optional)

Cable for the testing monitor

Template

Power Terminal Block

Used to test the camera connection to

a portable display device

Product installation guide

Plugged in the power plug

PNO-9080R

PNV-9080R

PND-9080R/ PNO-9080R/

PNV-9080R

PND-9080R/ PNO-9080R/

PNV-9080R

PND-9080R/ PNO-9080R/

PNV-9080R

PND-9080R/ PNO-9080R/

PNV-9080R

PND-9080R/

PNV-9080R

PND-9080R/

PNV-9080R

Tapping Screw

Used for installation on the wall or

ceiling

PND-9080R

PNO-9080R

3 PNV-9080R

RJ45 waterproof accessory

Sunshield

Sunshield Hold

CAUTION: Be ware of the Rated Voltage and Polarity

of the power connection.

Power Cable

Audio/alarm cable

Used to install in humid places PNO-9080R

It protects the camera from the direct

It fixes the sunshield with the camera. PNO-9080R

Used to connect with the audio and

sunlight.

Used to plug into the power port PNV-9080R

alarm port

PNO-9080R

PNV-9080R

English _7

overview

RESET

Appearance Item Name Quantity Description Model Name

Cable bush

Plastic Anchor

Machine Screws

Card-type moisture absorbent

Options (not included)

Pole mount bracket Cylindrical pole mounting bracket PNO-9080R

Indoor Buried Housing

Used to connect the LAN cable with a

diameter of Ø7~8.5.

For fixing a screw, Inserted in a hole

(reinforced anchoring force)

Used for assembling the dome case

when installing the product on the pipe,

wall mount, etc. or blocking a hole.

Attached when installed. PNV-9080R

Housing for installing indoor buried

type cameras

PNV-9080R

PND-9080R/

PNV-9080R

AT A GLANCE (PND-9080R)

Appearance

Item Description

Dome cover

Camera Case

Microphone hole

Case cover used to protect the lens and the main unit.

Housing part that covers the camera body.

Microphone is embedded.

8_ overview

Components

Item Description

Inside cover Protective cover for the main body.

Illumination Sensor Detects incoming light to control the IR LED.

c db

RESET

VIOEO

1 2 3

ALARM

OUT :1

DC 12V

ALARM

IN :2

GND :3

Lens Lens for the camera.

IR LED These infrared LED’s are controlled by the illumination sensor.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that DHCP can be

Reset Button

Zoom/Focus Control Button

Test Monitor Out

Alarm I/O Port

Power Port Port for power terminal block.

Micro SD Memory Card

Compartment

enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

T Zoom in (Tele)

W Zoom out (Wide)

N Focusing on a near object (Near)

F Focusing on a far object (Far)

Focus Control Press this button for automatic focus control.

Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.

ARM-IN Used to connect the alarm input sensor or external day/night sensor.

ARM-OUT Used to connect the alarm output signal.

GND These are common ports to connect alarm input/output signals.

Compartment for the Micro SD memory card.

●● OVERVIEW

Audio In Jack Used to connect to a microphone.

klm nj

Audio Out Jack Used to connect to speakers.

Network Port Used to connect the PoE or Ethernet cable for network connection.

Microphone hole Microphone is embedded.

English _9

overview

AT A GLANCE (PNO-9080R)

Appearance

Item Description

Micro SD card slot

Sunshield Hold

Sunshield

Reset Button

Zoom/Focus Control Button

Test Monitor Out

(Internal space of the product) This is a slot in which you can insert a Micro SD card.

It fixes the sunshield with the camera.

It protects the camera from the direct sunlight.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

T Zoom in (Tele)

W Zoom out (Wide)

N Focusing on a near object (Near)

F Focusing on a far object (Far)

Focus Control Press this button for automatic focus control.

Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.

d e f

If you reset the camera, the network settings will be adjusted so that DHCP can be enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

Components

CAUTION:Be ware of the

Rated Voltage and Polarity of the power connection.

b c

d e

Item Description

Power Port Used to plug the power cable.

ARM-OUT Used to connect the alarm output signal.

Alarm I/O Port

Network Port Used to connect the PoE or Ethernet cable for network connection.

Audio Out Jack Used to connect to speakers.

Audio In Jack Used to connect to a microphone.

GND These are common ports to connect alarm input/output signals.

ARM-IN Used to connect the alarm input sensor or external day/night sensor.

10_ overview

Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied ethanol.

AT A GLANCE (PNV-9080R)

Components

Appearance

Dome cover

Camera Case

Item Description

Case cover used to protect the lens and the main unit.

Housing part that covers the camera body.

ALARM

h ji

AUDIO

ACT

NETWORK

a cb

●● OVERVIEW

+ -

AC 24V /

/ DC 12V

RESET

VIDEO

d e fg

LINK

English _11

overview

Illumination Sensor Detects incoming light to control the IR LED.

Lens Lens for the camera.

IR LED These infrared LED’s are controlled by the illumination sensor.

Power Port Port for power terminal block.

Test Monitor Out

Zoom/Focus Control Button

Reset Button

Micro SD Memory Card

Compartment

Audio and alarm cable port

Item Description

Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.

T Zoom in (Tele)

W Zoom out (Wide)

N Focusing on a near object (Near)

F Focusing on a far object (Far)

Focus Control Press this button for automatic focus control.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that DHCP can be

Compartment for the Micro SD memory card.

Plug in the audio and alarm cable to this port to connect with external alarm device/ microphone/speaker.

Network Port Used to connect the PoE or Ethernet cable for network connection.

12_ overview

installation & connection

INSTALLATION (PND-9080R)

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

Disassembling

1. Use one hand to hold the camera’s bottom part and turn the cover

counterclockwise with another hand to separate it.

2. Lift up the inner cover to separate it.

Dome Cover

Installation

1. Attach the installation template to the selected area and punch 3

holes as shown in the figure.

●● INSTALLATION & CONNECTION

2. Using 2 tapping screws provided, fix the camera at 2 holes drilled

with a template.

Set the < > mark imprinted on the camera to face the direction of camera

monitoring.

3. Connect the camera internal terminal with the corresponding

cable.

4. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. (page 18)

We recommend you not to touch the lens as the camera lens has been

RESET

VIOEO

1 2 3

ALARM

OUT :1

ALARM

IN :2

GND :3

DC 12V

properly focused in the final process of manufacturing. If so, the lens may be out of focus or stained by alien substances.

5. Please connect the inner cover to the main body.

6. While grabbing the bottom side of the camera with your hand, please

grab and push its cover with the other hand to align the two arrow signs, as shown in the figure.

To assemble the dome cover, make the arrows match each other and press the

cover firmly. If the dome cover is rotated during assembly or is assembled incorrectly, diffused reflection may occur or the lens section may rotate, which will cause the shooting

RESET

VIOEO

1 2 3

ALARM

OUT :1

ALARM

IN :2

GND :3

DC 12V

range to be changed.

Make sure that the dome cover is correctly connected to the bottom part as shown

in the figure. If the snap-fit is not connected correctly, the dome cover may fall, which may cause injury.

DC 12V

GND :3

IN :2 ALARM

OUT :1

ALARM

1 2 3

VIOEO

RESET

English _13

installation & connection

INSTALLATION (PNO-9080R)

This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are

recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

Installation

1. Fix the Bottom cover using the 4 tapping screws provided.

2. Hang the safety cable up on a hook that looks like an arrow in the

Bottom cover.

3. Connect the appropriate cables with camera terminals.

4. Tighten the 3 screws on the Top cover using the L wrench

provided.

5. Adjust the camera direction using the L wrench provided.

When you adjust the camera position using a bracket, please loosen the

bracket screw, adjust the camera, and tighten it. If you attempt to adjust it forcibly while the screw is tight, it may result in a scratch or other problems.

How to connect the RJ45 waterproof cable to a LAN cable

1. Insert it through the arrow direction.

2. Connect the LAN connector (male) to the cable.

3. Connect the RJ45 modular jack (female) to the RJ45 connector

(male).

Please, keep each of the parts separated.

4. Assemble by rotating the RJ45 modular jack (female) and the RJ45

protection cover clockwise (Follow the arrow).

5. Assemble by rotating RJ45 protection cover and back cover

clockwise (Follow the arrow). When the back cover is assembled, the cable waterproof gasket is tightly attached to the cable to make it waterproof.

RJ45 modular

jack (female)

RJ45 connector (male)

Rubber ring

RJ45 connector protection cover

Back cover

Rubber ring

Cable waterproof

gasket

14_ installation & connection

You must fully assemble it to rotate the back cover up to the end of the screw

thread of the RJ45 connector.

Outdoor installation

When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside.

1. Connect the power, I/O, AUDIO, and LAN cables.

2. Wrap the black cable jacket (Area A) and the cable connection

area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.

If the cable jacket is not waterproofed properly, then it can directly cause

leakage. Make sure to protect the cable with a dense layer of taping.

Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.

Camera

System

INSTALLATION (PNV-9080R)

This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are

recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

Disassembling

1. Using the L wrench provided, turn the 3 fastening bolts

on the dome cover counter clockwise to remove the cover.

Dome cover

●● INSTALLATION & CONNECTION

Bolts

Camera Body

+ -

AC 24V /

/ DC 12V

Camera Case

RESET

VIDEO

English _15

installation & connection

AC 24V /

/ DC 12V

+ -

Installation

1. Drill a hole (diameter : 6mm, depth : min 55mm) of the case

bottom and insert the provided plastic anchor to the end.

2. Fit the bottom hole to the anchor hole and insert and fix the taping

screw (M4.5xL50).

3. Connect and arrange the necessary cables lest that they should

be damaged or twisted while installing the camera.

4. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. (page 18)

5. Close the dome cover.

`Securely fasten the fastening bolt using an L wrench to prevent water from

leaking.

Connecting waterproof power cable and LAN cable

1. Remove the dome cover and the case.

2. Pull out the long projected part of the rubber plug on the bottom and

remove it as shown in the figure.

Use an appropriate cable bush for the LAN cable to be connected.

- Basic camera : Use the cable with a diameter of Ø5~6.5.

- Components provided : Use the cable with a diameter of Ø7~8.5.

3. Insert the power cable into the small hole made by removing the projected part of the rubber plug in step 2 above, and lay the cable along the long groove.

4. Connect the power cable with the power terminal block.

5. Insert the LAN cable into the large hole made by removing the projected

part of the rubber plug in step 2 above.

6. Remove the sheath with a cable cutter, and align the cables.

VIDEO

RESET

/ DC 12V

AC 24V /

+ -

7. Connect the LAN cable with a LAN connector, and insert it into the LAN

tool.

8. Connect the finished cable to the Ethernet port.

ACT

ALARM AUDIO

LINK

NETWORK

CAUTION: Be ware of the Rated Voltage and Po larit y

of the power connec tion.

Connecting the alarm and audio cable

1. Remove the dome cover and the case.

2. Pull out the rubber plug on the bottom as shown in the figure.

3. Insert the alarm/audio cable through the hole created by removing the

rubber cap in No. 2, and connect the cable to the alarm terminal.

4. Align the cable so that it should not be damaged or jammed when

installing the camera.

+ -

AC 24V / / DC 12V

RESET

VIDEO

5. Put the rubber cap located on the alarm/audio cable in the hole.

6. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section.

(page 18)

7. Attach the dome cover.

ACT

ALARM AUDIO

NETWORK

LINK

16_ installation & connection

Attaching to the unbundled adapter

Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience.

1. Remove the dome cover from the case by referring to the “Disassembling”

section. (page

)

2. Use the provided machine screw to fix the camera case to the unbundled

adapter.

3. Connect and arrange the necessary cables lest that they should be

damaged or twisted while installing the camera.

4. Install the camera body in the reverse order of “Disassembling”.

5. Adjust the lens in a desired direction by referring to the “Adjusting the

monitoring direction for the camera” section. (page

)

6. Close the dome cover.

`Securely fasten the fastening bolt using an L wrench to prevent water from leaking.

Outdoor installation

1. Connect the power, I/O, BNC, and LAN cables.

2. Wrap the black cable jacket (Area A) and the cable connection area

with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.

If the cable jacket is not waterproofed properly, then it can directly cause

leakage. Make sure to protect the cable with a dense layer of taping.

Waterproof butyl tape is made of butyl rubber that can be stretched to twice

its normal length.

Camera

System

Optional Accessories for Installation

For your easier installation, you can purchase appropriate optional accessories available.

1. WALL MOUNT ADAPTOR(SBP-300WM or SBP-300WM1)/ HANGING MOUNT(PND-9080R : SBP-300HM8, PNV-9080R : SBP-300HM6) This adaptor is used when installing the dome camera onto a wall.

2. CEILING MOUNT ADAPTOR(SBP-300CM)/HANGING MOUNT(PND9080R : SBP-300HM8, PNV-9080R : SBP-300HM6) This adaptor is used when installing the dome camera on a concrete ceiling.

3. POLE MOUNT ADAPTOR(SBP-300PM) This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP300WM1) installation on a pole whose diameter is bigger than 80mm.

●● INSTALLATION & CONNECTION

4. CORNER MOUNT ADAPTOR (SBP-300KM)

This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP-300WM1) installation on the corner of wall joint.

English _17

installation & connection

Adjusting the monitoring direction for the camera (PND-9080R/PNV-9080R)

Pan

VIDEO

RESET

/ DC 12V

AC 24V /

+ -

Tilt

Lens rotation

`Adjusting the monitoring direction

You can adjust the camera direction only when the camera is fixed on the ceiling. Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called Tilt, and turning the lens on its axis is called Rotation.

- The effective range of pan is a total of 354 degrees.

- The effective range of rotation is a total of 355 degrees.

- The effective range of tilt is a total of 67 degrees.

The image can be covered up by the camera case depending on the angle.

Do not forcefully turn the focus/zoom lens after the dome case is disassembled.

Otherwise, it may cause an incorrect focus due to a motor failure.

`Methods of adjustment

1. After installing the camera, adjust the panning angle in consideration of the monitoring direction.

2. Set the horizontal angle so that the image is not reversed.

3. Adjust the tilt angle so that the camera faces toward the monitoring object.

INSERTING/REMOVING A MICRO SD MEMORY CARD

Disconnect the power cable from the camera before inserting the Micro SD memory card.

Do not insert the Micro SD memory card while it’s upside down by force.

Otherwise, it may damage the Micro SD memory card.

When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.

Disassembly of the product cover should be finished within 5 minutes, or there will be the risk of internal dew condensation.

Inserting a Micro SD Memory Card (PNO-9080R)

1. Loosen two screws on the camera.

2. Pull and separate the front cover.

3. Insert a Micro SD card in the arrow direction shown in the figure.

DESICCANTS

18_ installation & connection

Inserting a Micro SD Memory Card (PND-9080R/PNV-9080R)

NETWORK

LINK

ACT

AUDIO

ALARM

NETWORK

LINK

ACT

AUDIO

ALARM

1. Separate the Dome cover of the camera.

2. Insert a Micro SD card in the arrow direction shown in the figure.

<PND-9080R>

ALARM AUDIO

ACT

NETWORK

Removing a Micro SD Memory Card

Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.

●● INSTALLATION & CONNECTION

<PND-9080R>

LINK

<PNO-9080R>

<PNV-9080R>

ALARM

ACT

LINK

AUDIO

NETWORK

English _19

installation & connection

Pressing too hard on the Micro SD memory card can cause the card to shoot out uncontrollably from the slot when released.

Before removing your Micro SD memory card, turn off the camera or go to <Storage>, turn the device off, and press the [Apply

(

)] button. (Page 55)

If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or

damaged.

MEMORY CARD INFORMATION (NOT INCLUDED)

What is a memory card?

The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices.

Selecting a memory card that’s suitable for you

Your camera supports Micro SD/SDHC/SDXC memory cards. You may, however, experience compatibility issues depending on the model and make of the memory card.

For your camera, we recommend you use a memory card from the following manufacturers: Micro SD/SDHC/SDXC Memory Card : Sandisk, Transcend

It is recommended to use a 4 to 128GB (uhs-1 class) memory card for this camera.

Playback performance can be affected depending on the speed of memory card, so use the high-speed memory card.

To save a 4K resolution video, it is recommended to use a uhs-3 class (MLC type) memory card with a storage space of 16GB or higher.

Memory Card Components

Contacts

CONNECTING WITH OTHER DEVICE

Ethernet

DC 12V

<PND-9080R>

Power

Ethernet

CAUTION:Be ware of the

Rated Voltage and Polarity of the power connection.

Monitor to install

RESET

VIOEO

1 2 3

ALARM

OUT :1

ALARM

IN :2

GND :3

Power

Micro SD/SDHC/SDXC

20_ installation & connection

Monitor to install

<PNO-9080R>

+ -

AC 24V /

/ DC 12V

RESET

VIDEO

ALARM AUDIO

ACT

NETWORK

LINK

Monitor to install

Ethernet

Power

CAUTION: Be ware of th e

Rated Voltage and Polar ity

of the power con nectio n.

<PNV-9080R>

The CVBS out terminal of the product is provided for easier installation, and is not recommended for monitoring purposes.

Ethernet Connection

Connect the Ethernet cable to the local network or to the Internet.

Power Supply (PND-9080R)

Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera.

If both PoE and DC 12V are applied simultaneously, the product will be supplied with power from PoE.

- You can also use a router featuring PoE to supply power to the camera.

- Use PoE that is compliant with the IEEE 802.3af protocols.

- It is advisable to use only one power source from PoE and DC 12V.

Be careful not to reverse the polarity when you connect the power cable.

If you want to connect an external device, you must turn off the external device before proceeding.

Power Supply (PNO-9080R/PNV-9080R)

Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera.

When supplying PoE and DC 12V or PoE and AC 24V power at the same time, the equipment is powered by the external

source (AC 24V, DC 12V).

- You can also use a router featuring PoE to supply power to the camera.

- Use PoE that is compliant with the IEEE 802.3af protocols.

- It is recommended to use a single source for powering the equipment among PoE, DC 12V and AC 24V.

Be careful not to reverse the polarity when you connect the power cable.

AC 24V can be connected in non-polar union.

If you want to connect an external device, you must turn off the external device before proceeding.

Power Cable Specification for Each Model

In case of DC 12V Input:

Wire Type (AWG) #22 #20 #18

Cable Length (Max.) 24m 38m 60m

In case of AC 24V Input:

Wire Type (AWG) #22 #20 #18

Cable Length (Max.)

PNO-9080R

PNV-9080R

34m 55m 88m

Network Cable Specification

Item Contents Remark

Connector RJ45 (10/100/1000BASE-T)

Ethernet 10/100/1000BASE-T

Cable UTP Category 6

Max Distance 100M

PoE Support IEEE 802.3af

To operate with 1000BASE-T, a cable of

UTP-6 or higher should be used for the

Giga hub.

●● INSTALLATION & CONNECTION

English _21

installation & connection

Connecting to Audio Input/Output

Microphone

Amp

Microphone

Amp

Speaker

<PND-9080R/PNO-9080R>

Speaker

Microphone

Speaker

Microphone

Network

Amp

Microphone

Speaker Amp

Speaker

Microphone

Network

1. Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of the amplifier that the microphone is connected to.

You can use the built-in microphone in the camera without connecting an external microphone.

(only available in PND-9080R)

2. Connect the AUDIO OUT port of the camera with the speaker or LINE IN port of the amplifier that the speaker is connected to.

3. Check the specifications for audio input.

• Audio Codec

- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate: 16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz), AAC (Bit Rate: 48Kbps / Sampling Frequency: 16kHz)

• Full duplex Audio

• Audio in (PND-9080R) : Selectable (microphone/Line-in/Built-in microphone), Supported voltage: 2.5VDC

(4mA), Input impedance: 2K Ohm

• Audio in (PNO-9080R/PNV-9080R) : Selectable (microphone/Line-in), Supported voltage: 2.5VDC (4mA),

Input impedance: 2K Ohm

• Audio out : Line-out (3.5mm mono jack), Maximum output: 1Vms

• Line out impedance : 600Ω

Connecting to the I/O port box

Connect the Alarm I/O cable to the corresponding port of the port box.

RESET

VIOEO

1 2 3

ALARM

OUT :1

ALARM

IN :2

GND :3

DC 12V

Sensor Alarm

(Warning lamp)

22_ installation & connection

AmpSpeaker

Speaker

<PND-9080R>

Microphone

Amp

Microphone

<PNV-9080R>

CAUTION:Be ware of the

Rated Voltage and Polarity of the power connection.

To connect the external sensor

Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port, and connect the other strand to the [GND] port.

(Warning lamp)

SensorAlarm

<PNO-9080R>

ACT

ALARM AUDIO

NETWORK

LINK

Alarm

Sensor

(Warning lamp)

<PNV-9080R>

• ALARM-IN : Used to connect the alarm input sensor or external day/night sensor.

• ALARM-OUT : Used to connect the alarm output signal.

• GND : Common port for alarm in/output signal.

Alarm In Wiring Diagram

External

connection

Sensor

Inside of the camera

GND

VCC_3.3V

RESISTOR RESISTOR

RESISTORALARM IN (5mA SINK)

TRANSISTOR

MLCC

GND

DIODE

To connect the alarm out

If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open collector method, it may cause malfunction.

Refer to the alarm out connection diagram below when connecting devices that exceed the voltage and current specifications.

Alarm Out Wiring Diagram

Warning lamp /

Siren power

(-) (+)

Warning lamp /

Siren

External connection Inside of the camera

DC 5V or 3.3V

DIODE

RELAY

RESISTOR 10K ohm

TRANSISTOR

GND

ALARM OUT (12VDC 20mA MAX)

RESISTOR

TRANSISTOR

GND

●● INSTALLATION & CONNECTION

If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open

collector method, it may cause malfunction. Refer to the “Alarm Out Wiring Diagram” when connecting devices that exceed the voltage and current specifications. (page

23)

English _23

network connection and setup

AC 24V / DC 12V

RESET

VIDEO

+ -

AC 24V /

/ DC 12V

RESET

VIDEO

+ -

AC 24V / DC 12V

RESET

VIDEO

+ -

AC 24V /

/ DC 12V

RESET

VIDEO

+ -

You can set up the network settings according to your network configurations.

CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING

Connecting to the camera from a local PC in the LAN

1. Launch an Internet browser on the local PC.

2. Enter the IP address of the camera in the address bar of the browser.

Camera

INTERNET

Camera

Local PC

A remote PC in an external Internet out of the LAN network may not be able to connect to the camera installed in the intranet

if the port-forwarding is not properly set or a firewall is set. In this case, to resolve the problem, contact your network administrator.

In the IP installer, you can use the initial password, “4321” to set IP Address, Subnet Mask, Gateway, HTTP Port, VNP Port, IP

type. After changing the network interface, for better security, access the web viewer and change the password.

By factory default, the IP address will be assigned from the DHCP server automatically.

If there is no DHCP server available, the IP address will be set to 192.168.1.100. To change the IP address, use the IP Installer. For further details on IP Installer use, refer to “Static IP Setup”. (Page 26)

External Remote PC

DDNS Server (Data Center, KOREA)

CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM

DSL/Cable Modem

Camera

1. Connect the user PC directly with the network camera.

2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on

your desktop to connect to the Internet.

3. Use the Internet browser to connect to the web viewer.

4. Move to [Setup] page.

5. Move to [Network] – [DDNS] and configure the DDNS settings.

6. Move to [Basic] – [IP & Port], and set the IP type to [DHCP].

7. Connect the camera, which was removed from your PC, directly to the modem.

8. Restart the camera.

For configuring the DDNS settings, refer to “DDNS”. (page 51)

For registering the DDNS settings, refer to “Registering with DDNS”. (page 51)

Refer to “IP & Port” for how to setup IP. (page 44)

INTERNET

DDNS Server (Data Center, KOREA)

External Remote PC

24_ network connection and setup

CONNECTING THE CAMERA DIRECTLY TO A PPPoE MODEM

AC 24V / DC 12V

RESET

VIDEO

+ -

AC 24V /

/ DC 12V

RESET

VIDEO

+ -

AC 24V / DC 12V

RESET

VIDEO

+ -

AC 24V /

/ DC 12V

RESET

VIDEO

+ -

PPPoE Modem

Camera

INTERNET

External Remote PC

CONNECTING THE CAMERA TO A BROADBAND ROUTER WITH THE PPPoE/CABLE MODEM

This is for a small network environment such as homes, SOHO and ordinary shops.

●● NETWORK CONNECTION AND SETUP

DDNS Server (Data Center, KOREA)

1. Connect the user PC directly with the network camera.

2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on

your desktop to connect to the Internet.

3. Use the Internet browser to connect to the web viewer.

4. Move to [Setup] page.

5. Move to [Network] – [DDNS] and configure the DDNS settings.

6. Move to [Basic] – [IP & Port] Setup Page, set the IP type to [PPPoE], and enter the network service’s ID

and password.

7. Connect the camera, which was removed from your PC, directly to the modem.

8. Restart the camera.

For configuring the DDNS settings, refer to “DDNS”. (page 51)

For registering the DDNS settings, refer to “Registering with DDNS”. (page 51)

Refer to “IP & Port” for how to setup IP. (page 44)

Camera

INTERNET

PPPoE or

Cable Modem

DDNS Server (Data Center, KOREA)

External Remote PC

Camera

Local PC

Broadband

Router

PPPoE or

Cable Modem

Configuring the network settings of the local PC connected to a Broadband Router

Configuring the network settings of the local PC connected to a Broadband Router, follow the instructions below.

• Select : <Network>  <Properties>  <Local Area Connection>  <General>  <Properties>  <Internet Protocol (TCP/IP)>  <Properties>  <Obtain an IP address automatically> or <Use the following IP address>.

• Follow the instructions below if you select <Use the following IP address>: ex1) If the address (LAN IP) of the Broadband Router is 192.168.1.1

IP address : 192.168.1.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.1.1

ex2) If the address (LAN IP) of the Broadband Router is 192.168.0.1

IP address : 192.168.0.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.0.1

ex3) If the address (LAN IP) of the Broadband Router is 192.168.xxx.1

IP address : 192.168.xxx.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.xxx.1

For the address of the Broadband Router, refer to the product’s documentation.

For more information about port forwarding of the broadband router, refer to “Port Range Forward (Port Mapping) Setup”.

(Page 28)

English _25

+ 57 hidden pages