Samsung PN43E450A1FXZA Schematic

Page 1
PN43E450A1FXZA
FIRMWARE
6/5/12
PL51E450A1FXZP / PN43E440A2FXZA /
PN43E450A1FXZA / PN43E450A1FXZC /
Version: 1011.1
Avail on GSPN or Samsung,Com
Always check for latest updates
SERVICE BULLETINS
-None listed as of 6/5/12
Quick Parts: Verify before Ordering
HELP : 888-751-4086; 866-894-0637 FE)
GSPN
http://gspn3.samsungcsportal.com
PLUS ONE
http://my.plus1solutions.net/clientPortals/sam sung
HOT TIPS
-New 2012 Model… always check for latest
bulletins and firmware updates.
-New combined X/Y Main Board
Y-Buffer
X/Y
Main
Speaker
Fast Track Troubleshooting Manual – Rev 6/5/12
Vs Va Vsc Ve Volts Label
SMPS
X-Buffer
Logic
Main
Speaker
Function
1
Page 2
PN43E450A1FXZA
Fast Track Troubleshooting Manual
Page 3
E450 Power On Sequence
CN804 (SMPS) – CN4005
SMPS
SMPS
Main
X-Buffer
CN801
Main
X-Buffer
To
Logic
Board
3
Page 4
E450 Supply Adjustments
SMPS Adj.
X/Y Main Adj.
Adjustment locations may slightly vary with size/version
4
Page 5
Fast Track Troubleshooting Manual
Note: Some TVs may just have PC Pads instead of pins on Logic Test Jig. Simply connect to the 3 & 4 pads.
Power Supply Trouble Shooting Notes:
2010/2011/2012 models
Will not be run when the “X“ or “Y” or “Y/X” Main are disconnected. The SMPS will shut down immediately. However if a meter is first connected to the test point when power is applied it will read the correct voltage briefly before shutting down.(You have enough time to check key voltages!)
CAUTION: Do not reconnect any connectors to SMPS or Y/X Board(s)
until power has been turned off long enough for Vs to drop below 10V or damage will occur to X/ Y Board(s).
. VITAL SIGNS check Vs, Va, Vsc & Ve
When troubleshooting, It’s very important to first check Vs, Va, Vsc
& Ve
If Vs is missing (0V), disconnect power and check for short. Use ohm meter to measure resistance while disconnecting Y/X-Board supply feed. Turn Power On and Test SMPS with short connector removed for correct Vs voltage verification. (It may only come up briefly but to full level). Again be careful not to reconnect Power Connectors until Vs falls below 10V.
If Va is low or missing, disconnect Supply Feed to Logic Buffer Boards and check to see if SMPS Supply is restored. .
If Vsc is low or missing and Vs was OK, the failure is with the Y/X-
Board since the Y-Board section generates the Vsc voltage from the
Vs supplied by the SMPS.
If Ve is low or missing and Vs is OK, the failure is with the Y/X-Board since the Ve is generated by the X-Board section from the Vs supplied by the SMPS
Other SMPS Voltages: Check Low Voltage feeds to the Main Board and other supplied Assemblies.
Over Current Protection
For the SMPS Power Supply... If a short circuit occurs on either the VS or VA voltage lines, the SMPS stops operating, but should not fail. When the short circuit is removed from the source line, the Power Supply will operate normally again. Many SMPS Supplies
are replaced needlessly!
5
Page 6
Standby A3.3V
on Function Connector, Pin
3.
All Pins should
read 3.3V before commands.
Press, at Key 1,
Pin 6. 3.3V to
Function Control Troubleshooting
0.0V DC
Left, Right, Up,
Down at
Key 2, Pin 7.
Check specific
voltages on
chart.
6
Page 7
Fast Track Troubleshooting Manual
TROUBLESHOOTING VIDEO PROBLEMS
1. Verify Video Operation:
A. Customer Picture Test B. “Display” C. If display & Customer Picture Test are OK source is suspected D. Substitute with known good source and cabling.
2. Using Test Patterns in
M-STAR
Test Patterns
M-STAR
NOTE: Y/X MAIN
BOARD (E490/450)
Are Combined
Service Mode:
Customer Remote
A. Power off B. Mute, 182, Power
Factory Remote:
A. Power On B. Info, Test
3. Verify M-STAR Patterns
4. Verify Logic Patterns
If Logic Patterns are OK and M-
Star are noisy, replace the defective LVDS Cable or Main Board.
If M-Star and Logic Patterns are
both noisy check for specific
on screen noise error to
determine failure. (next slide)
NOTE: Y/X MAIN
BOARD (E490/450)
Are Combined
M-STAR
Models Sample
7
Page 8
ON SCREEN FAILURE EXAMPLES: NOTE: X/Y MAIN Combined.
Fast Track Troubleshooting Manual
ALIGNMENTS:
1. Check/Adj. VS, VA, VE, & VSC according to Panel Label
and Diffusion test. (see bulletins for any special notes before making changes)
DIFFUSION TEST/ADJ. (cell miss-firing)
- Allow the unit to warm up 15 to 20 minutes
- Access the Burn Protect Sig. Pattern in Cust. Menu.
-Adjust the Vs volts until screen errors are gone in
both dark and bright areas.
-Adjust the Vs volts within +/- 10V on the panel label.
-NOTE: Diffusion may appear with aging panels.
New panels with Diffusion consult bulletins and/or report problem.
2. Check/Set Option Bytes: Verify with latest table update info as well.
51 DHHcD
PE450
8
Loading...