Samsung PL42C450B1, PL50C450B1 User Manual

Page 1
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
Comuníquese con SAMSUNG WORLD WIDE
Si desea formular alguna pregunta o comentario en relación con los productos de Samsung, comuníquese con el centro de atención al cliente de SAMSUNG.
Country
ARGENTINE 0800-333-3733 www.samsung.com
BRAZIL 0800-124-421
CHILE 800-SAMSUNG(726-7864) www.samsung.com
Nicaragua 00-1800-5077267 www.samsung.com
Honduras 800-7919267 www.samsung.com
COSTA RICA 0-800-507-7267 www.samsung.com
ECUADOR 1-800-10-7267 www.samsung.com
EL SALVADOR 800-6225 www.samsung.com
GUATEMALA 1-800-299-0013 www.samsung.com
JAMAICA 1-800-234-7267 www.samsung.com
PANAMA 800-7267 www.samsung.com
PUERTO RICO 1-800-682-3180 www.samsung.com
REP. DOMINICA 1-800-751-2676 www.samsung.com
TRINIDAD & TOBAGO 1-800-SAMSUNG(726-7864) www.samsung.com
VENEZUELA 0-800-100-5303 www.samsung.com
COLOMBIA 01-8000112112 www.samsung.com
Customer Care Center
4004-0000
Web Site
www.samsung.com
Plasma TV
user manual
© 2010 Samsung Electronics Co., Ltd. All rights reserved.
imagine the possibilities
Thank you for purchasing this Samsung product. To receive more complete service, please register your product at
Model _____________ Serial No. _____________
BN68-02771A-01
Page 2
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance. Product design and specifications may be changed without notice.
User Instructions
Screen Image retention
Do not display a still image (such as on a video game) on the plasma display panel for more than several minutes as it can cause screen image
retention. This image retention is also known as ‘screen burn’. To avoid such image retention, refer to page 13 of this manual to reduce the degree of brightness and contrast of the screen when displaying a still image.
Heat on the top of the Plasma TV
The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole in the upper part of the
product.
This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.
The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change in the surrounding environment such as temperature or
humidity. This is normal and not a defect of the unit.
Cell Defects
The PDP uses a panel consisting of 2,360,000(HD-level) to 6,221,000(FHD-level) pixels which require sophisticated technology to produce. However,
there may be a few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.
Avoid operating the TV at temperatures below 41°F (5°C)
A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the Plasma TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and center of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effects to the screen. Damages caused by the above effect are not covered by the Warranty.
After-images on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images for a long time.
Warranty
Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
2
English
Page 3
Contents
Getting Started
y List of Features .........................................................4
y Accessories ..............................................................4
y Viewing the Control Panel .........................................5
y Viewing the Remote Control ..................................... 6
y Connecting to an Antenna ........................................ 7
y Plug & Play (Initial Setup) ...........................................7
Connections
y Connecting to an AV Device ......................................8
y Connecting to an Audio Device ................................. 9
y Connecting to a PC .................................................. 9
y Changing the Input Source ..................................... 10
Basic Features
y How to Navigate Menus .......................................... 11
y Channel Menu ........................................................ 11
Seeing Channels 11 Using Favorite Channels 12 Memorizing Channels 12 Editing Channels 12 Other Features 12
y Picture Menu .......................................................... 13
Changing the Preset Picture Mode 13 Adjusting Picture Settings 13 Economical Solutions 14 Changing the Picture Options 14 Setting up the TV with Your PC 16
y Sound Menu ........................................................... 16
Changing the Preset Sound Mode 16 Adjusting Sound Settings 16 Sound Settings 16
y Setup Menu ............................................................ 17
Setting the Time 17 Using the Sleep Timer 18 Setting the On / Off Timer 18 Other Features 18 Picture In Picture (PIP) 19
y Support Menu ......................................................... 20
Advanced Features
y Media Play .............................................................. 21
Connecting a USB Device 21 Screen Display 22 Playing Multiple Files 25 Media Play - Additional Functions 26
y Anynet+ .................................................................. 27
Setting Up Anynet+ 28 Switching between Anynet+ Devices 28 Recording 29 Listening through a Receiver 29 Troubleshooting for Anynet+ 30
Other Information
y FM Transmitter Setup .............................................. 31
Frequency Configuration 31 FM Transmitter Installation Guide 31 Supported FM Transmitter formats 32
y Installing the Wall Mount ......................................... 32
y Securing the Installation Space ............................... 33
y Securing the TV to the wall ..................................... 34
To Avoid the TV from Falling 34
y Troubleshooting ...................................................... 35
y Specifications ......................................................... 38
y License ................................................................... 38
y Index ...................................................................... 39
ENGLISH
t
This function can be used by pressing the
TOOLS button on the remote control.
Check the Symbol!
Note Step by Step Guide
Indicates additional information. Check here for instructions on how to open
the relevant submenu within the OSD
(on screen display).
English
3
Page 4

Getting Started

List of Features

y Media Play (USB): Allows you to play some music files, pictures saved on a USB device. (p. 21) y Self Diagnosis: You can check to make sure picture and sound operate normally (p. 20)

Accessories

Please make sure the following items are included with your PDP TV. If any items are missing, contact your dealer.
The items’ colors and shapes may vary depending on the models.
y Remote Control & Batteries (AAA x 2) (Not available in some locations) y Owner’s Instructions y Warranty Card / Safety Guide (Not available in some locations)
y Blanking Bracket y FM Transmitter / FM Transmitter Clamp (3EA)
Input Cables (Sold Separately)
y Cleaning Cloth y Power Cord
(Not available in some locations)
HDMI HDMI-DVI Component Composite (AV) Coaxial (RF) VGA
4
English
Page 5

Viewing the Control Panel

The product color and shape may vary depending on the model.
01 Getting Started
Power Indicator
Speakers
SOURCE
MENU Displays an on-screen menu, the OSD (on screen display) of your TV’s features.

Power Indicator Blinks and turns off when the power is on and lights up in standby mode.
Remote control sensor Aim the remote control towards this spot on the TV.
Standby mode
Do not leave your TV in standby mode for long periods of time (when you are away on a holiday, for example). A small amount of electric power is still consumed even when the power button is turned off. It is best to unplug the power cord.
(Power)
Toggles between all the available input sources. In the on-screen menu, use this button as you would use the ENTER button on the remote control.
Adjusts the volume. In the OSD, use the and buttons on the remote control.
Changes the channels. In the OSD, use the and buttons on the remote control.
Turns the TV on or off.
Remote control sensor
buttons as you would use the
buttons as you would use the
English
5
Page 6
Getting Started

Viewing the Remote Control

Turns the TV on and off.
Press to directly access channels.
Not Available.
Adjusts the volume.
Brings up the OSD.
Displays Media Play (USB) (p. 21).
Quickly select frequently used functions.
Returns to the previous menu.
These buttons are for the Channel List,
Media Play (USB) menu, etc.
Use these buttons in Media Play (USB)
and Anynet+ (HDMI-CEC) modes
(p. 21, 27).
(: Controls recording for Samsung
recorders that have the Anynet+ feature)
A B C D
S.MODE
P.MODE MTS
FAV.CH
P.SIZE
HDMI
SLEEP
Displays and selects the available video sources (p. 10).
Returns to the previous channel. Cuts off the sound temporarily.
Changes channels.
Displays the channel list on the screen (p. 11).
Selects the HDMI mode directly.
Displays information on the TV screen.
Selects the on-screen menu items and changes the values seen on the menu.
Exits the menu.
S.MODE: Press to select the sound
mode (p. 16).
P.MODE: Press to select the picture
mode (p. 13).
MTS: Press to choose stereo, mono
or Separate Audio Program (SAP broadcast) (p. 17).
FAV.CH: Displays Favorite Channel Lists
on the screen (p. 12).
P.SIZE: Selects the picture size
(p. 15).
SLEEP: Automatically shuts off the TV at
a preset time (p. 18).
Installing batteries (Battery size: AAA)
English
6
NOTE
Use the remote control within 23 feet from the TV.
x
Bright light may affect the performance of the remote
x
control. Avoid use when nearby fluorescent lights or neon signs.
The color and shape may vary depending on the model.
x
Page 7

Connecting to an Antenna

POWER
When the TV is initially powered on, basic settings proceed automatically.
Connecting the power cord and antenna.
VHF/UHF Antenna
Cable
or
Power Input

Plug & Play (Initial Setup)

When the TV is initially powered on, a sequence of on-screen prompts will assist in configuring basic settings. Press the
POWER button. Plug & Play is available only when the Input source is set to TV.
To return to the previous step, press the Red button.
Selecting a language
1
Selecting Store Demo
2
or Home Use
Selecting an antenna
3
Selecting a channel
4
Setting the Clock Set the Day, Month, Year, Hour, Minute, or am/pm.
Press the or button, then press the ENTER desired OSD (On Screen Display) language.
Press the or button, then press the ENTER
y Select the Home Use mode. Store Demo Mode is for retail
environments.
y To return the unit’s settings from Store Demo to Home Use
(standard): Press the volume button on the TV. When you see the volume OSD, press and hold MENU for 5 sec.
Press the or button, then press the ENTER Air+Cable.
Press the or button, then press the ENTER to memorize. When setting the antenna source to Cable, a step appears allowing you to assign numerical values (channel frequencies) to the channels. For more information, refer to Channel Auto Program (p.12).
Press the ENTER button at any time to interrupt the memorization process.
button. Select the
button.
button. Select Air, Cable or
button. Select the channel source
ANT OUT
P
5
Viewing the
6
HD Connection Guide. Enjoy your TV.
The connection method for the best HD screen quality is displayed.
Press the ENTER
button.
7
01 Getting Started
If You Want to Reset This Feature . . .
MENU Setup Plug & Play ENTER
English
7
Page 8

Connections

(DVI)
USB
HDMI IN 3
(DVI)

Connecting to an AV Device

Using an HDMI or HDMI/DVI cable: HD connection (up to 720p/1080i)
Available devices: DVD, Blu-ray player, HD cable box, HD STB (Set-Top-Box) satellite receiver.
W
R
Red White
HDMI IN 1(DVI), 2, 3, PC/DVI AUDIO IN
When using an HDMI/DVI cable connection, you must use the HDMI IN 1(DVI) jack for video. A DVD, Blue-ray
x
player, HD cable box, HD STB satellite receiver may require a DVI-HDMI (DVI to HDMI) cable or DVI-HDMI (DVI to HDMI) adapter. The PC/DVI AUDIO IN jack is required for audio.
If an external device such as a DVD, Blu-ray player, cable box, STB satellite receiver supporting HDMI
x
versions older than 1.3 is connected, the TV may operate abnormally (e.g. no screen display / no sound / annoying flicker / abnormal color).
If there is no sound after connecting an HDMI cable, check the HDMI version of the external device. If you
x
suspect the version is older than 1.3, contact the provider of the device to confirm the HDMI version and request an upgrade.
It is recomended you purchase an HDMI-certified cable. Otherwise, the screen may appear blank or a
x
connection error may occur.
Using a Component (up to 720p/1080i) or Audio/Video (480i only) Cable
Available devices: DVD, Blu-ray player, cable box, STB satellite receiver, VCR
Device Device
HDMI OUT
DVI OUT
AUDIO OUT
W R
R-AUDIO-L
W
R
Red White Red Blue Green Red White Yellow
When connecting to AV IN 1, the color of the AV IN 1 [Y/VIDEO] jack (green) will not match the video cable
R GB
Device
R
R
AUDIO OUT
R-AUDIO-L
W
W
R GB
R B G
COMPONENT OUT
PR PB Y
Device
AUDIO OUT
R-AUDIO-L
WR
WR
VIDEO OUT
(yellow).
To obtain the best picture quality, the Component connection is recommended over the A/V connection.
English
8
R W
Y
Y
Y
Page 9

Connecting to an Audio Device

(DVI)
R-AUDIO-L
Using an Optical (Digital) or Audio (Analog) Cable Connection
Available devices: Digital Audio System, Amplifier, DVD home theater
W
R
Red White
DIGITAL AUDIO OUT (OPTICAL)
When a digital audio system is connected to the DIGITAL AUDIO OUT (OPTICAL) jack, decrease the volume
x
of both the TV and the system.
5.1 CH (channel) audio is available when the TV is connected to an external device supporting 5.1 CH.
x
When the receiver (amplifier or DVD home theater) is set to on, you can hear sound output from the TV’s
x
optical jack. When the TV is receiving a DTV signal, the TV will send 5.1 CH sound to the amplifier or DVD home theater. When the source is a digital component such as a DVD / Blu-ray player / cable box / STB (Set-Top-Box) satellite receiver and is connected to the TV via HDMI, only 2CH audio will be heard from the amplifier or DVD home theater. If you want to hear 5.1 CH audio, connect the digital audio out jack from your DVD / Blu-ray player / cable box / STB satellite receiver directly to an amplifier or home theater.
AUDIO OUT: Connects to the audio input jacks on your Amplifier/Home theater.
When connecting, use the appropriate connector.
x
When an audio amplifier is connected to the AUDIO OUT jacks: Decrease the volume of the TV and adjust the
x
volume level with the Amplifier’s volume control.
02 Connections
Digital Audio System
OPTICAL
Amplifier / DVD home theater
AUDIO IN
Using an HDMI/DVI Cable or a D-sub Cable

Connecting to a PC

AUDIO OUT
DVI OUT
AUDIO OUT
PC OUT
English
9
Page 10
Connections
SOURCE
Display Modes (D-Sub and HDMI/DVI Input)
Optimal resolution
y 42": 1024 X 768 @ 60Hz y 50": 1360 X 768 @ 60Hz
Mode Resolution
IBM
MAC
VESA CVT
VESA DMT
VESA GTF
640 x 350 720 x 400
640 x 480 832 x 624
720 x 576
1280 x 720
640 x 480 640 x 480 640 x 480 800 x 600 800 x 600
800 x 600 1024 x 768 1024 x 768 1024 x 768 1280 x 720 1360 x 768
1280 x 720 52.500 70.000 89.040 -/+
Horizontal Frequency
(KHz)
31.469
31.469
35.000
49.726
35.910
56.456
31.469
37.500
37.861
37.879
46.875
48.077
48.363
56.476
60.023
45.000
47.712
NOTE
For HDMI/DVI cable connection, you must use the HDMI IN 1(DVI) jack.
x
The interlace mode is not supported.
x
The set might operate abnormally if a non-standard video format is selected.
x
Separate and Composite modes are supported. SOG(Sync On Green) is not supported.
x
Vertical
Frequency
(Hz)
70.086
70.087
66.667
74.551
59.950
74.777
59.940
75.000
72.809
60.317
75.000
72.188
60.004
70.069
75.029
60.000
60.015
Pixel Clock
Frequency
(MHz)
25.175
28.322
30.240
57.284
32.750
95.750
25.175
31.500
31.500
40.000
49.500
50.000
65.000
75.000
78.750
74.250
85.500
Sync Polarity
(H / V)
+/-
-/+
-/-
-/-
-/+
-/+
-/-
-/-
-/­+/+ +/+ +/+
-/-
-/­+/+ +/+ +/+
42" 50"
 
 
        
 
 
 
         

Changing the Input Source

Source List
Use to select TV or an external input sources such as a DVD / Blu-ray player / cable box / STB satellite receiver.
MENU Input Source List ENTER
■ TV / PC / AV1 / AV2 / Component1 / Component2 / HDMI1/DVI / HDMI2 / HDMI3 / USB
You can only choose external devices that are connected to the TV. In the Source List, connected inputs will be highlighted.
In the Source List, PC is always activated.
English
10
Edit Name
MENU Input Edit Name ENTER
■ VCR / DVD / Cable STB / Satellite STB / PVR STB / AV Receiver / Game / Camcorder / PC / DVI PC / DVI Devices / TV / IPTV / Blu-ray / HD DVD / DMA:
Name the device connected to the input jacks to make your input source selection easier.
When connecting an HDMI/DVI cable to the
HDMI IN 1(DVI) port, you should set the TV to DVI PC
or DVI Devices mode under Edit Name.
Page 11

Basic Features

CH LIST

How to Navigate Menus

Before using the TV, follow the steps below to learn how to navigate the menu and select and adjust different functions.

Channel Menu

03 Basic Features
 Seeing Channels
1
2
3 4
1 MENU button: Displays the main on-screen menu. 2 ENTER
3 RETURN button: Returns to the previous menu. 4 EXIT button: Exits the on-screen menu.
How to Operate the OSD (On Screen Display)
The access step may differ depending on the selected menu.
1
2 3 4 5
6
select an item. Confirm the setting.
/ Direction button: Move the cursor and
MENU
/ Select an icon with the or
ENTER
/
/
ENTER
EXIT
The main menu options appear on the screen:
Picture, Sound, Channel, Setup, Input, Application, Support.
button. Press ENTER to access the
sub-menu. Select the desired submenu with
the or button. Adjust the value of an item with the
or button. The adjustment in the OSD may differ depending on the selected menu.
Press ENTER to confirm the selection.
Press EXIT.
7
Channel List
Add, delete or set favorite channels and use the program guide for digital broadcasts.
MENU → Channel → Channel List
ENTER
Select a channel in the All Channels, Added Channels, Favorite or Programmed
screen by pressing the / and ENTER buttons. Then you can watch the selected channel.
Added Channels
All Channels: Shows all currently available channels.
Programmed: Shows all currently reserved
programs.
Using the color buttons with the Channel List
x x
number.
x
Select desired channels and press the Yellow button to set all the selected channels at the same time. The
 
x
x
(The options menus may differ depending on the situation.)
Channel Status Display Icons
3 Air
4 Air
5 * Air 6 Air 7 Air
8 Air 9 Air 10 Air
Air Antenna Zoom Select  Page
Added Channels: Shows all added channels.
Favorite: Shows all favorite channels.
Red (Antenna): Switches to Air or Cable. Green (Zoom): Enlarges or shrinks a channel
Yellow (Select): Selects multiple channel lists.
mark appears to the left of the selected channels.
(Page): Move to next or previous page.
(Tools): Displays the Channel List option menu.

Tools
Icons Operations
A channel selected.
A channel set as a Favorite.
A reserved Program.
A locked channel.
English
11
Page 12
Basic Features
 Using Favorite Channels
MENU Channel Channel List ENTER
Add to Favorite / Delete from Favorite
Set channels you watch frequently as Favorites.
1. Select a channel and press the TOOLS button.
2. Add or delete the channel using the Add to Favorite or Delete from Favorite menu respectively.
Added Channels
To show all Favorite channels, click on the button shown on the rignt.
3 Air
4 Air
5 * Air 6 Air 7 Air
8 Air 9 Air 10 Air
Air Antenna Zoom Select  Page
Delete
Add to Favorite
Lock
Timer Viewing
Channel Name Edit
Select All

Tools
FAV.CH
 Memorizing Channels
MENU Channel ENTER
Antenna (Air / Cable)
Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an Air or a Cable system).
Auto Program
Air: Air antenna signal.
Cable: Cable antenna signal.
Air+Cable: Air and Cable antenna signals.
If you want to stop Auto Programming, press the
ENTER button. The Stop Auto Program? message
will be displayed. Select Yes by pressing the or button, then press the ENTER
button.
 Editing Channels
MENU Channel Channel List ENTER
Channel Name Edit
1. Select a channel and press the TOOLS button.
2. Edit the channel name using the Channel Name Edit
menu.
Channel Name Edit: Assign your own channel name.

Other Features

MENU Channel ENTER
Channel List
Channel List Option Menu
Set each channel using the Channel List menu options (Add / Delete, Lock / Unlock, Timer Viewing, Select All / Deselect All). Option menu items may differ depending on the channel status.
1. Select a channel and press the TOOLS button.
2. Select a function and change its settings.
Add / Delete: Delete or add a channel to display the
channels you want.
NOTE
All deleted channels will be shown on the
x
All Channels menu. A gray-colored channel indicates the channel
x
has been deleted. The Add menu only appears for deleted
x
channels. Delete a channel from the Added Channels or
x
Favorite menu in the same manner.
Lock / Unlock: You can lock a channel so that the
channel cannot be selected and viewed.
This function is available only when the Child Lock is set to On.
The PIN input screen appears. Enter your 4-digit PIN, the default of which is “0-0-0-0”. Change the PIN using the Change PIN option.
Timer Viewing: You can set a desired channel to be
displayed automatically at the reserved time. Set the current time first to use this function.
1. Press the / / / buttons to select the desired channel in Channel List.
2. Press the TOOLS button, then select Timer Viewing.
12
English
Page 13
3. Scroll up or down to adjust the settings in the box,
or use the numeric buttons on your remote to enter the date and time.
If you selected Once, Every Week or Every Day in Repeat, you can enter the date you want.
4. Select OK, then press the ENTER
done.
NOTE
Only memorized channels can be reserved.
x
Reserved programs will be displayed in the
x
Programmed menu.
Select All: Select all the channels in the Channel List.
Deselect All: Deselect all the selected channels.
You can only select Deselect All when one or more channels are selected.
button when
Programmed
(in Channel List) You can view, modify or delete a show that you have
reserved to watch. Programmed timer viewing is displayed here. Highlight a program and press the TOOLS button to display Options.
Change Info: Change a show you have reserved to
watch. Begin with step 3 of “Timer Viewing,” above.
Cancel Schedules: Cancel a show you have reserved
to watch.
This deletes the highlighted or selected program(s).
Information: Display a show you have reserved
to watch. (You can also change the reservation Information.) Alternatively, you can view Information by highlighting a program and pressing the ENTER button.
Select All / Deselect All: Select or deselect all reserved
programs.
Fine Tune
If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, fine tune the channel manually. Scroll to the left or right until the image
is clear.
Settings are applied to the channel you're currently watching.
Fine tuned channels that have been saved are marked with an asterisk “*” on the right-hand side of the channel number in the channel banner.
To reset the fine-tuning, select Reset.
Color System (Auto / PAL-M / PAL-N / NTSC)
Normally the TV can receive image and sound with good quality when in the mode auto. This mode detects the signal color system automatically. In case of some signal reception with color unsatisfactory, select the Color System Mode to PAL-M, PAL-N or NTSC.

Picture Menu

 Changing the Preset Picture Mode
MENU Picture Mode ENTER
Mode
Select your preferred picture type.
Dynamic: Suitable for a bright room.
Standard: Suitable for a normal
environment.
Movie: Suitable for watching movies in
a dark room.
 Adjusting Picture Settings
MENU Picture ENTER
P.MODE
Cell Light / Contrast / Brightness / Sharpness / Color / Tint (G/R)
Your television has several setting options for picture quality control.
NOTE
When you make changes to Cell Light, Contrast,
x
Brightness, Sharpness, Color or Tint (G/R) the OSD will be adjusted accordingly.
In PC mode, you can only make changes to
x
Cell Light, Contrast and Brightness. Settings can be adjusted and stored for each
x
external device connected to the TV.
03 Basic Features
English
13
Page 14
Basic Features
 Economical Solutions
MENU Picture Eco Solution ENTER
The Eco Function can be used to enhance your power savings.
Eco Solution
■ Energy Saving (Off / Low / Medium / High / Picture Off)
the TV in order to reduce power consumption. If you select Picture Off, the screen is turned off, but the sound remains on. Press any button except volume button to turn on the screen. Until the screen turns on again, a distorted picture will be displayed for about 4 seconds.
Eco Sensor (Off / On): To enhance your power savings; the picture settings will automatically adapt to the light in the room.
Min Cell Light: When Eco Sensor is On, the minimum screen brightness can be adjusted manually.
No Signal Power Off (Off / 15 min. / 30 min. / 60 min.): To avoid unnecessary energy consumption, set how long you want the TV to remain on if it’s not receiving a signal.

Changing the Picture Options

If you adjusts the Cell Light, the Eco Sensor will be set to Off.
If Eco Sensor is On, the display brightness may change (become slightly darker or brighter) depending on the surrounding light intensity.
Disabled when the PC is in power saving mode.
: This adjusts the brightness of
Advanced Settings
MENU Picture Advanced Settings ENTER
(Advanced Settings are available in Standard / Movie mode) Compared to previous models, new Samsung TVs have a
more precise picture.
In PC mode, you can only make changes to Dynamic Contrast, Gamma and White Balance.
Advanced Settings
Black Tone : Off
Dynamic Contrast : Medium
Gamma : 0
RGB Only Mode : Off
Color Space : Native
White Balance
Flesh Tone : 0
Move

Enter

Return
Black Tone (Off / Dark / Darker / Darkest): Select the
black level to adjust the screen depth.
Dynamic Contrast (Off / Low / Medium / High): Adjust
the screen contrast.
Gamma: Adjust the primary color intensity.
RGB Only Mode (Off / Red / Green / Blue): Displays the Red, Green and Blue color for making fine adjustments to the hue and saturation.
Color Space (Auto / Native): Adjust the range of colors available to create the image.
White Balance: Adjust the color temperature for a more natural picture.
R-Offset / G-Offset / B-Offset: Adjust each color’s (red, green, blue) darkness.
R-Gain / G-Gain / B-Gain: Adjust each color’s (red, green, blue) brightness.
Reset: Resets the White Balance to it’s default settings.
Flesh Tone: Emphasize pink “Flesh Tone.”
Edge Enhancement (Off / On): Emphasize object boundaries.
Picture Options
MENU Picture Picture Options ENTER
In PC mode, you can only make changes to the Color Tone, Size and Screen Burn Protection.
Picture Options
Color Tone : Normal
Size : 16:9
Digital Noise Filter : Auto
MPEG Noise Filter : Auto
HDMI Black Level : Normal
Film Mode : Off
Screen Burn Protection
Move

Enter

Return
Color Tone (Cool / Normal / Warm1 / Warm2)
Warm1 or Warm2 will be deactivated when the picture mode is Dynamic.
Settings can be adjusted and stored for each external device connected to an input on the TV.
Size: Your cable box/satellite receiver may have its own set of screen sizes as well. However, we highly recommend you use 16:9 mode most of the time.
P.SIZE
14
English
Page 15
16:9 : Sets the picture to 16:9 wide mode. Zoom1: Use for moderate magnification. Zoom2: Use for a stronger magnification. Wide Fit: Enlarges the aspect ratio of the picture to fit
the entire screen.
Available with HD 1080i / 720p signals in 16:9 mode..
4:3 : Sets the picture to basic (4:3) mode.
Do not watch in 4:3 format for a long time. Traces of borders displayed on the left, right and center of the screen may cause image retention(screen burn) which are not covered by the warranty.
Screen Fit: Displays the full image without any cut-off when HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p) signals are inputted.
NOTE
After selecting Zoom1, Zoom2 or Wide Fit:
x
1. Press the button to select Position.
2. Press the ENTER
3. Press the or button to move the picture up
or down.
4. Press the ENTER
5. Press the button to select Reset.
6. Press the ENTER
to its default position.
After selecting Screen Fit in HDMI (1080i/1080p) or
x
Component (1080i/1080p) mode, you may need to center the picture:
1. Press the or button to select Position.
2. Press the ENTER
3. Press the , , or button to move the
picture.
4. Press the ENTER
5. Press the or button to select Reset.
6. Press the ENTER
HD (High Definition): 16:9 - 1080i/1080p (1920x1080),
x
720p (1280x720) Settings can be adjusted and stored for each
x
external device you have connected to an input on the TV.
Input Source Picture Size
TV, AV, Component (480i, 480p)
Component (1080i, 1080p), HDMI (720p, 1080i, 1080p)
PC 16:9, 4:3
button.
button.
button to reset the picture
button.
button.
button.
16:9, Zoom1, Zoom2, 4:3
16:9, Wide Fit, 4:3, Screen Fit
■ Digital Noise Filter (Off / Low / Medium / High / Auto / Auto Visualisation / Demo): If the broadcast signal
received by your TV is weak, you can activate the Digital Noise Filter feature to reduce any static and ghosting that may appear on the screen.
When the signal is weak, try other options until the best picture is displayed.
Auto Visualisation: When changing analog channels, displays signal strength.
Only available for analog channels.
When bar is green, is that the best possible signal.
MPEG Noise Filter (Off / Low / Medium / High / Auto): Reduces MPEG noise to provide improved picture quality.
HDMI Black Level (Normal / Low): Selects the black level on the screen to adjust the screen depth.
Available only in HDMI mode.
Film Mode (Off / Auto1 / Auto2): Sets the TV to automatically sense and process film signals from all sources and adjusts the picture for optimum quality.
Available in TV, AV, COMPONENT (480i / 1080i) and HDMI (480i / 1080i).
Screen Burn Protection: To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. The Time setting allows you to program the time between movement of the picture in minutes.
Pixel Shift (Off / On): Using this function, you can minutely move pixels on the PDP in horizontal or vertical direction to minimize after-images on the screen.
Optimum condition for pixel shift
Item
Horizontal 0~4 4
Vertical 0~4 4
Time (minute) 1~4 min. 4 min.
The Pixel Shift value may differ depending on the TV size (inches) and mode.
This function is not available in the Screen Fit mode.
Auto Protection Time (10 min. / 20 min. / 40 min. / 1 hour / Off) : Set the time the screen remains idle
with a still image until the screen saver is activated. The Screen Saver prevents the formation of ghost images on the screen.
TV/AV/Component/
HDMI/PC
03 Basic Features
English
15
Page 16
Basic Features
Scrolling: This function removes after-images on the screen by moving all the pixels on the PDP according to a pattern. Use this function when there are remaining after-images or symbols on the screen, especially when you displayed a still image on the screen for a long time.
The after-image removal function has to be executed for a long time (approximately 1 hour) to effectively remove after-images on the screen. If the after-image is not removed after performing the function, repeat the function again.
Press any key on the remote control to cancel this feature.
Side Gray (Light / Dark): When you watch TV with the screen ratio set to 4:3, the screen is prevented from any damage by adjusting the white balance on both extreme left and right sides.
Picture Reset (OK / Cancel)
Resets your current picture mode to its default settings.
 Setting up the TV with Your PC
Set the input source to PC.
MENU Picture →ENTER
Auto Adjustment
Adjust frequency values/positions and fine tune the settings automatically.
Not available when connecting with an HDMI/DVI cable.
Screen
Coarse / Fine: Removes or reduces picture noise. If the
noise is not removed by Fine-tuning alone, then adjust the frequency as best as possible (Coarse) and Fine­tune again. After the noise has been reduced, readjust the picture so that it is aligned to the center of screen.
Position: Adjust the PC’s screen positioning if it does
not fit the TV screen. Press the or button to adjust the Vertical-Position. Press the or button to adjust the Horizontal-Position.
Image Reset: Resets the image to default settings.
Using Your TV as a Computer (PC) Display
Setting Up Your PC Software (Based on Windows XP) Depending on the version of Windows and the video card,
the actual screens on your PC will probably look different, but the same basic set-up information will apply in most cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1. Click on “Control Panel” on the Windows start menu.
2. Click on “Appearance and Themes” in the “Control
Panel” window and a display dialog-box will appear.
3. Click on “Display” and a display dialog box will appear.
4. Navigate to the “Settings” tab on the display dialog-box.
– The correct size setting (resolution)
[Optimum: 42": 1024 X 768 / 50": 1360 X 768 pixels]
– If a vertical-frequency option exists on your display
settings dialog box, the correct value is ‘60’ or ‘60 Hz’. Otherwise, just click ‘OK’ and exit the dialog box.

Sound Menu

 Changing the Preset Sound Mode
MENU Sound Mode ENTER
Mode
Standard: Selects the normal sound mode.
Music: Emphasizes music over voices.
Movie: Provides the best sound for movies.
Clear Voice: Emphasizes voices over other sounds.
Amplify: Increase the intensity of high-frequency sound to allow a better listening experience for the hearing impaired.
 Adjusting Sound Settings
MENU Sound Equalizer ENTER
S.MODE
Equalizer
Adjusts the sound mode (standard sound mode only).
Balance L/R: Adjusts the balance between the right and left speaker.
100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment): Adjusts the level of specific bandwidth frequencies.
Reset: Resets the equalizer to its default settings.
 Sound Settings
Virtual Surround (Off / On)
(standard sound mode only) This function provides a virtual 5.1 channel surround sound
experience through a pair of speakers using HRTF (Head Related Transfer Function) technology.
16
English
Page 17
Dialog Clarity (Off / On)
(standard sound mode only) This function allows you to increase the intensity of a voice
over background music or sound effects so that dialog can be heard more clearly.
Preferred Language
(digital channels only) Digital-TV broadcasts are capable of
simultaneous transmission of many audio tracks (for example, simultaneous translations of the program into foreign languages).
Not available in some locations.
You can only select a language among the ones being broadcasted.
Multi-Track Sound (MTS)
Mono: Choose for channels that are
broadcasting in mono or if you are having difficulty receiving a stereo signal.
Stereo: Choose for channels that are
broadcasting in stereo.
SAP: Choose to listen to the Separate
Audio Program, which is usually a foreign-language translation.
Depending on the particular program being broadcast, you can listen to Mono, Stereo or SAP.
MTS
MTS
SPDIF Output
SPDIF (Sony Philips Digital Interface) is used to provide digital sound, reducing interference going to speakers and various digital devices such as an A/V Receiver/Home theater.
Audio Format: During the reception of a digital TV broadcast, you can select the Digital Audio output (SPDIF) format from the options PCM, or Dolby Digital.
Audio Delay: Correct audio-video sync problems, when watching TV or video, and when listening to digital audio output using an external device such as an AV receiver (0ms ~ 250ms).
FM Transmitter
(Not available in some locations) You can listen to TV sound from FM receiver speaker by
transmitting audio signals by FM frequencies.
For more detailed information, refer to “FM Transmitter Setup” (p. 31).
Connecting a FM Transmitter
Insert FM Transmitter Module into the Socket which is located at the back side of TV.
TV Side Panel
03 Basic Features
Auto Volume (Off / Normal / Night)
To equalize the volume level on each channel, set to Normal.
Night: This mode provides an improved sound experience compared to Normal mode, making almost no noise. It is useful at night.
Speaker Select (External Speaker / TV Speaker)
A sound echo may occur due to a difference in decoding speed between the main speaker and the audio receiver. In this case, set the TV to External Speaker.
When Speaker Select is set to External Speaker, the volume and MUTE buttons will not operate and the sound settings will be limited.
When Speaker Select is set to External Speaker
TV Speaker: Off , External Speaker: On
x
When Speaker Select is set to TV Speaker
TV Speaker: On , External Speaker: On
x
If there is no video signal, both speakers will be mute.
FM Transmitter
FM Transmitter (Off / On): Turns FM transmitter on/off.
FM Frequency: Sets FM transmitter frequency.
Sound Reset (OK / Cancel)
Restore all sound settings to the factory defaults.

Setup Menu

 Setting the Time
MENU Setup Time ENTER
Time
Time: Setting the clock is for using various timer features
of the TV.
The current time will appear every time you press the INFO button.
English
17
Page 18
Basic Features
If you disconnect the power cord, you have to set the clock again.
Clock: Set the Day, Month, Year, Hour, Minute and am/pm manually.
You can set the Day, Month, Year, Hour and Minute directly by pressing the number buttons on the remote control.
 Using the Sleep Timer
MENU Setup Time Sleep Timer ENTER
Sleep Timer: Automatically shuts down the TV after a preset period of time. (30, 60, 90, 120, 150 and 180 minutes).
To cancel the Sleep Timer, select
Off.
 Setting the On / Off Timer
MENU Setup Time Timer 1 ENTER
You can set the TV to turn on automatically at a preset time.
Timer 1 / Timer 2 / Timer 3: Three different on / off timer settings can be made.
You must set the clock first.
On Time
Inactivate
Off Time
Inactivate
Volume
Repeat
Once
On Time / Off Time: Set the hour, minute, and activate / inactivate. (To activate the timer with the setting you’ve chosen, set to Activate.)
Volume: Set the desired volume level. Source : Select TV or USB content to be played when
the TV is turned on automatically. (USB can be selected only when a USB device is connected to the TV)
Antenna (when Source is set to TV): Select Air or Cable.
Channel (when the Source is set to TV): Select the
desired channel. Contents (when the Source is set to USB): Select a
folder in the USB device containing music or photo files to be played when the TV is turned on automatically.
Timer 1
00 00 am
00 00 am
Source
Sun Mon Tue Wed Thu Fri Sat
Antenna Channel
TV20 3
Move
Air
Adjust 
Enter

SLEEP
Return
NOTE
If there is no music file on the USB device or the
x
folder containing a music file is not selected, the Timer function does not operate correctly.
When there is only one photo file in the USB,
x
the Slide Show will not play. If a folder name is too long, the folder cannot be
x
selected. Each USB you use is assigned its own folder.
x
When using more than one of the same type of USB, make sure the folders assigned to each USB have different names.
Repeat: Select Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual to set at you convenience. If you
select Manual, you can set up the day you want to activate the timer.
The  mark indicates the day is selected.
Auto Power Off (available only when the TV is turned on by the Timer): The TV will be automatically turned off after 3 hours of being left idle to prevent overheating.
 Other Features
MENU Setup ENTER
Menu Language
Set the menu language.
1. Select Menu Language and press the ENTER
button.
2. Choose desired language and press the ENTER
button.
Caption
(On-Screen Text Messages)
Caption (Off / On): You can switch the caption function
on or off. If captions are not available, they will not be displayed on the screen.
The Caption feature doesn’t work in Component, HDMI or PC modes.
Caption Mode: You can select the desired caption
mode.
The availability of captions depends on the program being broadcast.
CC1~CC4 / Text1~Text4: The Analog Caption function operates in either analog TV channel mode or when a signal is supplied from an external device to the TV.
Service1~Service6 / CC1~CC4 / Text1~Text4: (digital channels only) The Digital Captions function works with digital channels.
Not available in some locations.
18
English
Page 19
Service1~6 may not be available in digital caption mode depending on the broadcast.
Digital Caption Options: (digital channels only)
Not available in some locations.
Size: Options include Default, Small, Standard and Large. The default is Standard.
Font Style: Options include Default and Styles 0 to 7. The default is Style 0.
Foreground Color: Options include Default, White, Black, Red, Green, Blue, Yellow, Magenta and Cyan. You can change the color of the letter. The default is White.
Background Color: Options include Default, White, Black, Red, Green, Blue, Yellow, Magenta and Cyan. You can change the background color of the caption. The default is Black.
Foreground Opacity: This adjusts the opacity of text. Options include Default, Transparent, Translucent, Solid and Flashing.
Background Opacity: This adjusts the opacity of the caption background. Options include Default, Transparent, Translucent, Solid and Flashing.
Return to Default: This option sets each Size, Font Style, Foreground Color, Background Color, Foreground Opacity and Background Opacity to its default.
NOTE
Digital Caption Options are available only
x
when Service1 ~ Service6 can be selected in Caption Mode.
The availability of captions depends on the
x
program being broadcasted. The Foreground and Background cannot be set
x
to have the same color. You cannot set both the Foreground Opacity
x
and the Background Opacity to Transparent.
General
Game Mode (Off / On): When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming experience by selecting the game menu.
NOTE
Precautions and limitations for game mode
x
– To disconnect the game console and connect
another external device, set Game Mode to Off in the setup menu.
– If you display the TV menu in Game Mode, the
screen shakes slightly.
Game Mode is not available when the input source
x
is set to TV or PC. After connecting the game console, set Game Mode
x
to On. Unfortunately, you may notice reduced picture quality.
If Game Mode is On:
x
Picture mode is set to Standard and Sound mode
is set to Movie.
Equalizer is not available.
Menu Transparency (Bright / Dark): Set the
Transparency of the menu.
Melody (Off / Low / Medium / High): Set so that a
melody plays when the TV is turned on or off.
AV Color System (Auto, PAL-M, PAL-N, NTSC): You
can set the color encoding standards for external signal inputs. Normally the TV can receive image and sound with good quality in Auto mode. This mode detects the color signal sources automatically. If the color implementation is unsatisfactory, select any of PAL-M, PAL-N or NTSC.
This function is available only in AV mode.

Picture In Picture (PIP)

PIP
You can watch the TV tuner and one external video source simultaneously. PIP (Picture-in-Picture) does not function in the same mode.
MENU Setup PIP ENTER
NOTE
For PIP sound, refer to the Sound Select instructions.
x
If you turn the TV off while watching in PIP mode, the
x
PIP window will disappear. You may notice that the picture in the PIP window
x
becomes slightly unnatural when you use the main screen to view a game or karaoke.
PIP Settings
x
Main picture Sub picture Component1, 2, HDMI1/
DVI, HDMI2, HDMI3, PC
PIP (Off / On): Activate or deactivate the PIP function.
Air/Cable (Air / Cable): Select either Air or Cable as the
input source for the sub-screen.
Channel: Select the channel for the sub-screen.
Size (
Position (
sub-picture.
Sound Select (Main / Sub): You can choose the desired sound (Main / Sub) in PIP mode.
/ ): Select a size for the sub-picture.
/  /  / ): Select a position for the
TV
03 Basic Features
English
19
Page 20
Basic Features
H

Support Menu

MENU Support ENTER
Self Diagnosis
Self Diagnostic might take few seconds, this is part of the normal operation of the TV.
Picture Test: Use to check for picture problems. Yes: If the test pattern does not appear or there is
noise in the test pattern, select Yes. There may be a problem with the TV. Contact Samsung’s Call Center for assistance.
No: If the test pattern is properly displayed, select No. There may be a problem with your external equipment. Please check your connections. If the problem still persists, refer to the external device’s user manual.
Sound Test: Use the built-in melody sound to check for sound problems.
If you hear no sound from the TV’s speakers, before performing the sound test, make sure
Speaker Select is set to TV Speaker in the Sound menu.
The melody will be heard during the test even if Speaker Select is set to External Speaker or the sound is muted by pressing the MUTE button.
Yes: If you can hear sound only from one speaker or not at all during the sound test, select Yes. There may be a problem with the TV. Contact Samsung’s Call Center for assistance.
No: If you can hear sound from the speakers, select No. There may be a problem with your external equipment. Please check your connections. If the problem persists, refer to the external device’s user manual.
Troubleshooting: If the TV seems to have a problem, refer to this description.
If none of these troubleshooting tips apply, contact the Samsung customer service center.
Software Upgrade
Software Upgrade can be performed downloading the
latest firmware from “www.samsung.com,” to a USB memory device.
Current Version - the software already installed in the TV.
Software is represented as ‘Year/Month/Day_Version’.
Software Upgrade
Current Version 2010/01/18_000001
By USB
Alternative Software
Move

Enter

Return
Installing the Latest Version
By USB: Insert a USB
drive containing the firmware upgrade file, downloaded from “www. samsung.com,” into the TV. Please be careful not to disconnect the power or remove the USB drive until upgrades are complete. The TV will be turned off and on automatically after completing the firmware upgrade. When software is upgraded, video and audio settings you have made will return to their default settings. We advise you to to write down your settings so that you can easily reset them after the upgrade.
Alternative Software (Not available)
USB Drive
TV Side Panel
USB
HD Connection Guide
Refer to this information when connecting external devices to the TV.
Contact Samsung
View this information when your TV does not work properly or when you want to upgrade the software. You can find information regarding our call centers and how to download products and software.
20
English
Page 21

Advanced Features

H
SUM

Media Play

04 Advanced Features
MEDIA.P
Enjoy photos, music and/or movie fi les saved on a USB Mass Storage Class (MSC) device.
MENU Application Media Play
(USB) ENTER
MediaPlay
Videos
Change Device
View Devices
 Connecting a USB Device
1. Turn on your TV.
2. Connect a USB device containing photo, music and/or movie fi les to the
USB jack on the side of the TV.
3. When USB is connected to the TV, popup window appears. Then you can select Media Play.
It might not work properly with unlicensed multimedia files.
Need-to-Know List before using Media Play (USB)
MTP (Media Transfer Protocol) is not supported.
x
The file system supports FAT16, FAT32 and NTFS.
x
Certain types of USB Digital camera and audio devices may not be compatible with this TV.
x
Media Play only supports USB Mass Storage Class (MSC) devices. MSC is a Mass Storage Class Bulk-Only
x
Transport device. Examples of MSC are Thumb drives, Flash Card Readers and USB HDD (USB HUB are not supported). Devices should be connected directly to the TV’s USB port.
Before connecting your device to the TV, please back up your files to prevent them from damage or loss of data.
x
SAMSUNG is not responsible for any data file damage or data loss. Connect a USB HDD to the dedicated port, USB port.
x
Do not disconnect the USB device while it is loading.
x
The higher the resolution of the image, the longer it takes to display on the screen.
x
The maximum supported JPEG resolution is 15360X8640 pixels.
x
For unsupported or corrupted files, the “Not Supported File Format” message is displayed.
x
If the files are sorted by Basic View, up to 1000 files can be displayed in each folder.
x
MP3 files with DRM that have been downloaded from a non-free site cannot be played. Digital Rights Management
x
(DRM) is a technology that supports the creation, distribution and management of the content in an integrated and comprehensive way, including the protection of the rights and interests of the content providers, the prevention of the illegal copying of contents, as well as managing billings and settlements.
If more than 2 PTP devices are connected, you can only use one at a time.
x
If more than two MSC devices are connected, some of them may not be recognized. A USB device that requires high
x
power (more than 500mA or 5V) may not be supported. If an over-power warning message is displayed while you are connecting or using a USB device, the device may not
x
be recognized or may malfunction.
USB Drive

Enter

TV Side Panel
Return
USB
English
21
Page 22
Advanced Features
If the TV has been no input during time set in Auto Protection Time, the Screensaver will run.
x
The power-saving mode of some external hard disk drives may be released automatically when connected to the TV.
x
If a USB extension cable is used, the USB device may not be recognized or the files on the device may not be read.
x
If a USB device connected to the TV is not recognized, the list of files on the device is corrupted or a file in the list is
x
not played, connect the USB device to the PC, format the device and check the connection. If a file deleted from the PC is still found when Media Play is run, use the “Empty the Recycle Bin” function on the PC
x
to permanently delete the file.
 Screen Display
Move to the desired file using the up/down/right/left buttons and then press the ENTER or  (Play) button. The file is played.
Supports the View Devices and Home in Media Play homepage.
You can ascertain the selected
file name and the number of files
Displays the sorting standard.
The sorting standard is
different depending on the contents.
Information:
and page.
Sort List Section:
Videos
SUM
Change Device
/Movie 01.avi 1/1
Movie 01.avi
Movie 03.avi
Movie 05.avi
Movie 07.avi
Movie 09.avi
Jan.10.2010
Jan.10.2010
Jan.10.2010
Jan.10.2010
Jan.10.2010
Movie 02.avi
Movie 04.avi
Movie 06.avi
Movie 08.avi
Movie 10.avi
Select Sorting
Jan.10.2010
Jan.10.2010
Jan.10.2010
Jan.10.2010
Jan.10.2010

Page
File List Section: You can confirm the files and groups that are sorted by category.
Tools
Operation Buttons
Red (Change Device): Selects a connected device. Green (Preference): Sets the file preference. (not supported in Basic view) Yellow (Select): Selects multiple files from file list. Selected files are marked with a symbol. Blue (Sorting): Selects the sort list.
Tools: Displays the option menu.
Using the  (REW) or  (FF) button, file list can move to next or previous page.
22
English
Page 23
Videos
Movie 01.avi
00:04:03 / 00:07:38 1/1
SUM
Playing Video
1. Press the or button to select Videos, then press the ENTER
2. Press the /// button to select the desired video in the file list.
3. Press the ENTER
button or  (Play) button.
– The selected file is displayed on the top with its playing time. – If video time information is unknown, play time and progress bar are not displayed. – During video playback, you can search using the and button.
In this mode, you can enjoy movie clips contained on a Game, but you cannot play the Game itself.
y Supported Subtitle Formats
Name File extension Format
MPEG-4 time-based text .ttxt XML
SAMI .smi HTML
SubRip .srt string-based SubViewer .sub string-based Micro DVD .sub or .txt string-based
y Supported Video Formats
File Extension Container Video Codec Resolution
Divx 3.11 / 4.x / 5.1 / 6.0 1920x1080 6 ~ 30 8
*.avi
*.mkv
*.asf ASF
*.wmv ASF Window Media Video v9 1920x1080 6 ~ 30 25 WMA
*.mp4 MP4
*.3gp 3GPP
*.vro
*.mpg
*.mpeg
*.ts
*.tp
*.trp
AVI
MKV
VRO VOB
PS
TS
XviD 1920x1080 6 ~ 30 8
H.264 BP / MP / HP 1920x1080 6 ~ 30 25
MPEG4 SP / ASP 1920x1080 6 ~ 30 8
Divx 3.11 / 4.x / 5.1 / 6.0 1920x1080 6 ~ 30 8
XviD 1920x1080 6 ~ 30 8
H.264 BP / MP / HP 1920x1080 6 ~ 30 25
MPEG4 SP / ASP 1920x1080 6 ~ 30 8
H.264 BP / MP / HP 1920x1080 6 ~ 30 25
XVID 1920x1080 6 ~ 30 8
H.264 BP / MP / HP 1920x1080 6 ~ 30 25
MPEG4 SP / ASP 1920x1080 6 ~ 30 8
MPEG1 1920x1080 24 / 25 / 30 30 MPEG2 1920x1080 24 / 25 / 30 30 MPEG1 1920x1080 24 / 25 / 30 30
H.264 1920x1080 6 ~ 30 25
MPEG2 1920x1080 24 / 25 / 30 30
H.264 1920x1080 6 ~ 30 25
VC1 1920x1080 6 ~ 30 25
button in the Media Play menu.
Frame rate
(fps)
Bit rate (Mbps)
Pause

Jump

Tools

Return
Audio Codec
MP3 / AC3 / LPCM /
ADPCM / DTS Core
MP3 / AC3 / LPCM /
ADPCM / WMA
MP3 / ADPCM / AACMPEG4 SP / ASP 1920x1080 6 ~ 30 8
ADPCM / AAC / HE-AAC
AC3 / MPEG / LPCM
AC3 / MPEG / LPCM / AACMPEG2 1920x1080 24 / 25 / 30 30
AC3 / AAC / MP3 / DD+ /
HE-AAC
04 Advanced Features
English
23
Page 24
Advanced Features
Movie 01.avi
00:04:03 / 00:07:38 1/1
SUM
3/15
I Love you
Jhon
Music 1
No Singer
Music 2
No Singer
Music 3
No Singer
Music 4
No Singer
Music 5
No Singer
I Love You
Jhon
1st Album Pop 2010
4.2MB
01:10 / 04:02
SUM
Other Restrictions
NOTE
If there are problems with the contents of a codec, the codec will not be supported.
x
If the information for a Container is incorrect and the file is in error, the Container will not be able to play
x
correctly. Sound or video may not work if the contents have a standard bitrate/frame rate above the compatible Frame/sec
x
listed in the table above. If the Index Table is in error, the Seek (Jump) function is not supported.
x
Video Decoder Audio Decoder
• Supports up to H.264, Level 4.1
• H.264 FMO / ASO / RS, VC1 SP / MP / AP L4 and AVCHD are not supported.
• GMC is not supported.
• H.263 is not supported.
Playing movie continuously (Resume Play)
If you exit the playing movie function, the movie can be played later from the point where it was stopped.
1. Select the movie file you want to play continuously by pressing
the or button to select it from the file list section.
2. Press the
(Play) / ENTER button.
3. Select Play Continuously (Resume Play) by pressing the Blue
button. The Movie will begin to play from where it was stopped.
The Blue button is available when resuming play.
If the Continuous Movie Play Help function is set to On in the Settings menu, a pop-up message will appear when you resume play a movie file.
• Supports up to WMA 7, 8, 9, STD
• WMA 9 PRO does not support 2 channel excess multi channel or lossless audio.
• WMA sampling rate 22050Hz mono is not supported.
Play continuously
Resumes playing from the last viewed scene.
Play continuously

Pause

Jump

Tools

Return
Music
Playing Music
1. Press the or button to select Music, then press the
ENTER
button in the Media Play menu.
2. Press the /// button to select the desired Music file in
the file list.
3. Press the ENTER
Only displays the files with MP3 and PCM file extension. Other file extensions are not displayed, even if they are saved on the same USB device.
If the sound is abnormal when playing MP3 files, adjust the Equalizer in the Sound menu. (An over-modulated MP3 file may cause a sound problem.)
24
– During music playback, you can search using the and
button.
(REW) and  (FF) buttons do not function during play.
English
button or  (Play) button.
Pause

Playlist
Jump

Tools

Return
Page 25
Photos
1/1
/Movie 01.avi
SUM
Movie 01.avi
Jan.10.2010
Jan.10.2010
Jan.10.2010
Jan.10.2010
Jan.10.2010
Jan.10.2010
Jan.10.2010
Jan.10.2010
Jan.10.2010
Jan.10.2010
Movie 03.avi
Movie 05.avi
Movie 07.avi
Movie 09.avi
Movie 02.avi
Movie 04.avi
Movie 06.avi
Movie 08.avi
Movie 10.avi
Image1024.jpg 1024x768 2010/2/1 3/15
SUM
Viewing a Photo (or Slide Show)
1. Press the or button to select Photos, then press the
ENTER
button in the Media Play menu.
2. Press the /// button to select the desired photo in the
file list.
3. Press the ENTER
– While a photo list is displayed, press the
ENTER button on the remote control to start the slide
show. – All files in the file list section will be displayed in the slide show. – During the slide show, files are displayed in order.
Music files can be automatically played during the Slide Show if the Background Music is set to On.
The BGM Mode cannot be changed until the BGM has finished loading.

Playing Multiple Files

button or  (Play) button.
(Play) /
Normal
Pause

Previous/Next

Tools
04 Advanced Features

Return
Playing selected video/music/photo files
1. Press the Yellow button in the file list to select the desired file.
2. Repeat the above operation to select multiple files.
NOTE
The  mark appears to the left of the selected files.
x
To cancel a selection, press the Yellow button again.
x
To deselect all selected files, press the TOOLS button
x
and select Deselect All.
3. Press the TOOLS button and select Play Selected Contents.
Playing the video/music/photo file group
1. While a file list is displayed, move to any file in the desired group.
2. Press the TOOLS button and select Play Current Group.
Videos
Change Device
2 les selected Page
Select Sorting

Tools
English
25
Page 26
Advanced Features
 Media Play - Additional Functions
Sorting the file list
Press the Blue button in the file list to sort the files.
Category Operation Videos Music Photos
Basic View Title Preference
Latest Date Earliest Date Artist Album Genre Mood Monthly
Displays the whole folder. You can view the photo by selecting the folder. Sorts and displays the file title in Symbol/Number/Alphabet/Special order. Sorts and displays the file by preference. You can change the file preference in the file
list section using the Green button. Sorts and shows files by the latest date.
Sorts and shows files by the earliest date. Sorts the music file by artist in alphabetical order. Sorts the music file by album in alphabetical order. Sorts music files by the genre. Sorts music files by the mood. You can change the music mood information. Sorts and shows photo files by month.
Videos/Music/Photos Play Option menu
During file playback, press the TOOLS button.
Category Operation Videos Music Photos Title You can move the other file directly. Repeat Mode You can play movie and music files repeatedly. Picture Size
(Mode1 / Mode2 / Original) Picture Setting You can adjust the picture setting (p. 13, 14, 15, 16). Sound Setting You can adjust the sound setting (p. 16, 17). Subtitle Setting You can play the video with Subtitles. This function only works if the subtitles are the
Stop Slide Show / Start Slide Show
Slide Show Speed You can select the slide show speed during the slide show. Background Music You can set and select background music when watching a slide show. Zoom You can zoom into images in full screen mode. Rotate You can rotate images in full screen mode. Information You can see detailed information about the played file.
You can adjust the picture size to your preference.
same file name as the video. You can start or stop a slide show.
 
 
   
Settings
Using the Setup Menu
Continuous Movie Play Help (Resume Play) (On / Off): Select to display the help pop-up message for continuous movie
playback.
Get DivX® VOD registration code: Shows the registration code authorized for the TV. If you connect to the DivX web site
and register, you can download the VOD registration file. If you play the VOD registration using Media Play, the registration is completed.
For more information on DivX® VOD, visit “www.DivX.com.”
Get DivX® VOD deactivation code: When DivX® VOD is not registered, the registration deactivation code is displayed. If
you execute this function when DivX® VOD is registered, the current DivX® VOD registration is deactivated.
Information: Select to view information about the connected device.
English
26
Page 27

Anynet+

HDMI IN 3
04 Advanced Features
What is Anynet+?
Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung TV’s remote. The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your Samsung device has this feature, check if there is an Anynet+ logo on it.
To connect to a Samsung Home Theater
1. Connect the HDMI IN (1(DVI), 2, 3 or 4) jack on the TV and the HDMI OUT jack of the corresponding Anynet+ device
using an HDMI cable.
2. Connect the HDMI IN jack of the home theater and the HDMI OUT jack of the corresponding Anynet+ device using an
HDMI cable.
NOTE
Connect the Optical cable between the DIGITAL AUDIO OUT (OPTICAL) jack on your TV and the Digital Audio Input
x
on the Home Theater.
When following the connection above, the Optical jack only outputs 2 channel audio. You will only hear sound from
x
the Home Theater’s Front, Left and Right speakers and the subwoofer. If you want to hear 5.1 channel audio, connect
the DIGITAL AUDIO OUT (OPTICAL) jack on the DVD / Satellite Box (i.e. Anynet Device 1 or 2) directly to the
Amplifier or Home Theater, not the TV.
You can connect only one Home Theater.
x
You can connect an Anynet+ device using the HDMI cable. Some HDMI cables may not support Anynet+ functions.
x
Anynet+ works when the AV device supporting Anynet+ is in the standby or on status.
x
Anynet+ supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.
x
TV
(DVI)
Optical cable
Anynet+ Device 1
HDMI cable
HDMI cable
Home Theater
Anynet+ Device
2, 3, 4
HDMI cable
English
27
Page 28
Advanced Features
Anynet+ Menu
The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the TV.
Anynet+ Menu Description
View TV Changes Anynet+ mode to TV broadcast mode.
Device List Shows the Anynet+ device list.
(device_name) MENU Shows the connected device menus. E.g. If a DVD recorder is connected, the disc menu of
(device_name) INFO Shows the play menu of the connected device. E.g. If a DVD recorder is connected, the
Recording: (*recorder) Starts recording immediately using the recorder. (This is only available for devices that
Stop Recording: (*recorder) Stops recording.
Receiver Sound is played through the receiver.
If more than one recording device is connected, they are displayed as (*recorder) and if only one recording device is connected, it will be represented as (*device_name).
 Setting Up Anynet+
MENU Application Anynet+ (HDMI-CEC) ENTER
■ Setup Anynet+ (HDMI-CEC) (Off / On): To use the Anynet+ Function, Anynet+ (HDMI-CEC) must be set to On.
When the Anynet+ (HDMI-CEC) function is disabled, all the Anynet+ related operations are deactivated.
Auto Turn Off (No / Yes): Setting an Anynet+ Device to turn off automatically when the TV is turned off.
The active source on the TV must be set to TV to use the Anynet+ function.
Even if an external device is still recording, it may turn off.
the DVD recorder will appear.
play menu of the DVD recorder will appear.
support the recording function.)
 Switching between Anynet+ Devices
1. Anynet+ devices connected to the TV are listed.
If you cannot find a device you want, press the Red button to refresh the list.
2. Select a device and press the ENTER
Only when you set Anynet+ (HDMI-CEC) to On in the Application menu, the Device List menu appears.
Switching to the selected device may take up to 2 minutes. You cannot cancel the operation during the switching
x
operation. If you have selected external input mode by pressing the SOURCE button, you cannot use the Anynet+ function.
x
Make sure to switch to an Anynet+ device by using the Device List.
button. You can switch to the selected device.
28
English
Page 29
 Recording
You can make a recording of a TV Program using a Samsung recorder.
1. Select Recording.
When there are more than two recording devices
When multiple recording devices are connected, the recording devices are listed. Select one recording device in
x
the Device List.
When the recording device is not displayed, select Device List and press the Red button to search devices.
2. Press the EXIT button to exit.

You can record the source streams by selecting Recording: (device_name).

Pressing the  (REC) button will record whatever you are currently watching. If you are watching video from another device, the video from the device is recorded.
Before recording, check whether the antenna jack is properly connected to the recording device. To properly connect an antenna to a recording device, refer to the recording device’s users manual.
 Listening through a Receiver
You can listen to sound through a receiver (i.e Home Theater) instead of the TV Speaker.
1. Select Receiver and set to On.
2. Press the EXIT button to exit.
If your receiver supports audio only, it may not appear in the device list.
The receiver will work when you have properly connected the optical in jack of the receiver to the DIGITAL AUDIO
OUT (OPTICAL) jack of the TV.
When the receiver (i.e Home Theater) is set to On, you can hear sound output from the TV’s Optical jack. When the TV is displaying a DTV (air) signal, the TV will send out 5.1 channel sound to the receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the receiver.
NOTE
You can only control Anynet+ devices using the TV remote control, not the buttons on the TV.
x
The TV remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device.
x
The Anynet+ functions do not operate with other manufacturers’ products.
x
04 Advanced Features
English
29
Page 30
Advanced Features
 Troubleshooting for Anynet+
Problem Possible Solution
Anynet+ does not work. • Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
I want to start Anynet+. • Check if the Anynet+ device is properly connected to the TV and check if the Anynet+ (HDMI-CEC) is set to
I want to exit Anynet+. • Select View TV in the Anynet+ menu.
The message “Connecting to Anynet+ device...” appears on the screen.
The Anynet+ device does not play. • You cannot use the play function when Plug & Play (initial setup) is in progress.
• Only one receiver (home theater) can be connected.
• Check if the Anynet+ device power cord is properly connected.
• Check the Anynet+ device’s Video/Audio/HDMI cable connections.
• Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
• Check whether the TV remote control is in TV mode.
• Check whether the remote control is Anynet+ compatible.
• Anynet+ doesn’t work in certain situations. (Searching channels, operating Media Play (USB) or Plug & Play
(initial setup), etc.)
• When connecting or removing the HDMI cable, please make sure to search devices again or turn your TV off and on again.
• Check if the Anynet+ Function of Anynet+ device is set on.
On in the Anynet+ Setup menu.
• Press the TOOLS button to display the Anynet+ menu and select a menu you want.
• Press the SOURCE button on the TV remote control and select a non- Anynet+ device.
• Press z, PRE-CH, and FAV.CH to change the TV mode. (Note that the channel button operates only when a tuner-embedded Anynet+ device is not connected.)
• You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
• Use the remote control when the Anynet+ setting or switching to view mode is complete.
The connected device is not displayed.
The TV Program cannot be recorded.
The TV sound is not output through the receiver.
• Check whether or not the device supports Anynet+ functions.
• Check whether or not the HDMI cable is properly connected.
• Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
• Search Anynet+ devices again.
• You can connect an Anynet+ device using the HDMI cable only. Some HDMI cables may not support Anynet+ functions.
• If connection is terminated because there has been a power interruption or the HDMI cable has been disconnected, please repeat the device scan.
• Check whether the antenna jack on the recording device is properly connected.
• Connect the optical cable between TV and the receiver.
30
English
Page 31

Other Information

FM Transmitter Setup

This feature is not available in all countries.
 Frequency Configuration
y FM transmitter’s frequency must be set differently from any FM radio frequency in the vicinity of the TV in order to achieve
good signal receptivity free of radio interference.
y If a TV channel frequency falls within the FM frequency range, the FM transmitter will automatically update its permissible
frequency range.
y Identical TV channel and FM transmitter frequency will result in signal interference. To prevent this, the FM transmitter’s
frequency range is automatically displayed.
y If there is no TV channel frequency within the FM frequency range (83MHz to 108MHz), the entire range from 88.0MHz to
107.9MHz is available for use.
 FM Transmitter Installation Guide
The FM transmitter module features an integrated antenna. Antenna signal strength will vary depending on where the antenna is installed and on the performance of the receiver. If you experience poor signal strength, try installing the antenna in one of the methods shown below:
Method 1 Method 2
Connect the FM transmitter (fig. 1), attach the clamp (fig. 2) and hook the antenna lead to the clamp.
If the reception is inadequate after using “Method 1”, we recommend installing the transmitter using “Method 2”.
Unwind and position an antenna where the receiver gets best reception.
05 Other Information
2
1
NOTE
(Not available in some locations)
Installing the antenna directly on the back of the TV may result in poor
x
signal strength. Allow some room between the TV and the antenna. Having the FM transmitter antenna in direct contact with the TV
x
antenna can result in signal interference. If the FM Transmitter menu is not enabled, check that the FM
x
transmitter is correctly inserted into the 1 FM TRANSMITTER slot. To hear audio, transmitted from the TV in FM frequency, on an FM receiver (radio, home theater, etc.), move the
x
antenna of the FM receiver until the audio is clear. If you use an FM receiver (radio, home theater, etc.), you can enjoy quality audio transmitted from the TV via FM
x
frequency if your person is within 10 m of the receiver. Be sure to use the provided FM transmitter. Otherwise, the product may be damaged.
x
Avoid using the provided FM transmitter with other products.
x
English
31
Page 32
Other Information
Adjust the frequency of the FM receiver (radio, home theater, etc.) to the frequency of the FM transmitter on the TV. If
x
the frequency of the receiver does not match, the sound will not be heard. Adjust the volume of the FM receiver to an appropriate level.
x
When the TV is turned off, the FM receiver (radio, home theater, etc.) emits static noise.
x
Due to interference from other electronics, which is a weakness of wireless communications, you may hear sound
x
stuttering or static.
 Supported FM Transmitter formats
Name SPEC
Normal 88.0MHz ~ 107.9MHz
Frequency Rang
Transfer distance Maximum 5m : Depend on Antenna position and receiver quality
Assembling the Blanking Bracket
When installing the TV onto a wall, attach the Blanking Bracket as shown.
Match the TV Frequency

Installing the Wall Mount

Blanking Bracket
Automatic range setting
(In 88.0MHz ~107.9MHz)
Installing the Wall Mount Kit
The wall mount kit (sold separately) allow you to mount the TV on the wall. For detailed information on installing the wall mount, see the instructions provided with the wall mount. Contact a technician for
assistance when installing the wall mount bracket. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the
TV on your own.
Wall Mount Kit Specifications (VESA)
The wall mount kit is not supplied, but sold separately.
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest dealer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
NOTE
Standard dimensions for wall mount kits are shown in the table below.
x
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.
x
Do not use screws that do not comply with the VESA standard screw specifications.
x
Do not use screws that are longer than the standard dimension or do not comply with the VESA standard screw
x
specifications. Screws that are too long may cause damage to the inside of the TV set. For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ
x
depending on the wall mount specifications. Do not fasten the screws too strongly; this may damage the product or cause the product to fall, leading to personal
x
injury. Samsung is not liable for these kinds of accidents. Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or
x
the consumer fails to follow the product installation instructions.
32
English
Page 33
Do not mount the TV at more than a 15 degree tilt.
x
Always use two people to mount the TV to a wall.
x
05 Other Information
Product Family inches
42~50 400 X 400
58~63 600 X 400
PDP TV
70~79 800 X 400
80~ 1400 X 800
Unscrew the hole around before installing Wall-Mount on the wall.
Do not install your Wall Mount Kit while your TV is turned on. It may result in personal injury due to electric shock.
VESA Spec.
(A * B)
Standard
Screw
M8 4
Quantity

Securing the Installation Space

Keep the required distances between the product and other objects (e.g. walls) to ensure proper ventilation. Failing to do so may result in fire or a problem with the product due to an increase in the internal temperature of the product.
When using a stand or wall-mount, use parts provided by Samsung Electronics only.
If you use parts provided by another manufacturer, it may result in a problem with the product or an injury due to the
x
product falling.
The appearance may differ depending on the product.
Installation with a stand. Installation with a wall-mount.
4 inches
4 inches
4 inches
4 inches
4 inches
4 inches
4 inches
English
33
Page 34
Other Information

Securing the TV to the wall

Caution: Pulling, pushing, or climbing on the TV may cause the TV to fall. In particular, ensure your children do not hang over or destabilize the TV; doing so may cause the TV to tip over, causing serious injuries or death. Follow all safety precautions provided on the included Safety Flyer. For added stability, install the anti-fall device for safety purposes, as follows.
 To Avoid the TV from Falling
1. Put the screws into the clamps and firmly fasten them onto the wall.
Confirm that the screws have been firmly installed onto the wall.
You may need additional material such as an anchor depending on the type of wall.
Since the necessary clamps, screws, and string are not supplied, please purchase these additionally.
2. Remove the screws from the back center of the TV, put the screws into
the clamps, and then fasten the screws onto the TV again.
Screws may not be supplied with the product. In this case, please purchase the screws of the following specifications.
3. Connect the clamps fixed onto the TV and the clamps fixed onto the wall
with a strong cable and then tie the string tightly.
NOTE
Install the TV near to the wall so that it does not fall backwards.
x
It is safe to connect the string so that the clamps fixed on the
x
wall are equal to or lower than the clamps fixed on the TV. Untie the string before moving the TV.
x
4. Verify all connections are properly secured. Periodically check
connections for any sign of fatigue for failure. If you have any doubt about the security of your connections, contact a professional installer.
Wall
34
English
Page 35

Troubleshooting

If the TV seems to have a problem, first try this list of possible problems and solutions. If none of these troubleshooting tips apply, visit “www.samsung.com,” then click on Support, or contact a Samsung customer service center.
Issues Solutions and Explanations
Poor picture First of all, please perform the Picture Test and confirm that your TV is properly displaying test image.
The TV image does not look as good as it did in the store.
The picture is distorted: macroblock error, small block, dots, pixelization.
Color is wrong or missing. • If you’re using a component connection, make sure the component cables are connected to the
There is poor color or brightness. • Adjust the Picture options in the TV menu. ( go to Picture mode / Color / Brightness / Sharpness)
There is a dotted line on the edge of the screen.
The picture is black and white. • If you are using an AV composite input, connect the video cable (yellow) to the Green jack of
When changing channels, the picture freezes or is distorted or delayed.
Sound Problem First of all, please perform the Sound Test to confirm that your TV audio is properly operating.
There is no sound or the sound is too low at maximum volume.
The picture is good but there is no sound. • Set the Speaker Select option to TV Speaker in the Sound menu (p. 17).
The speakers are making an inappropriate noise.
(go to MENU - Support - Self Diagnosis - Picture Test) (p. 20) If the test image is properly displayed, the poor picture may caused by the source or signal.
• If you have an analog cable/satellite Box, upgrade to an HD digital set top box. Use HDMI or Component cables to deliver HD (high definition) picture quality.
• Cable/Satellite subscribers: Try HD stations from the channel line up.
• Antenna connection: Try HD stations after performing Auto program.
Many HD channels are upscaled from SD (Standard Definition) contents.
• Adjust the Cable/Sat box video output resolution to 1080i or 720p.
• Compression of video contents may cause picture distortion, especially in fast moving pictures such as sports and action movies.
• Low signal level can cause picture distortion. This is not a TV problem.
• Mobile phones used close to the TV (cca up to 1m) may cause noise in picture on analog and digital TV.
correct jacks. Incorrect or loose connections may cause color problems or a blank screen.
(p. 13)
• Adjust Energy Saving option in the TV menu. (go to MENUPictureEco Solution – Energy Saving) (p. 14)
• Try resetting the picture to view the default picture settings. (go to MENU - Picture - Picture Reset) (p. 16)
• If the picture size is set to Screen Fit, change it to 16:9 (p. 15).
• Change cable/satellite box resolution.
component input 1 on the TV.
• If connected with a cable box, please try to reset the cable box. Reconnect the AC cord and wait until the cable box reboots. It may take up to 20 minutes.
• Set the output resolution of the cable box to 1080i or 720p.
(go to MENU - Support - Self Diagnosis - Sound Test) (p.20) If the audio is OK, the sound problem may caused by the source or signal.
• Please check the volume the of device (Cable/Sat Box, DVD, Blu-ray etc) connected to your TV.
• If you are using an external device, make sure the audio cables are connected to the correct audio input jacks on the TV.
• If you are using an external device, check the device’s audio output option (ex. you may need to change your cable box’s audio option to HDMI when you have a HDMI connected to your TV).
• If you are using a DVI to HDMI cable, a separate audio cable is required.
• If your TV has a headphone jack, make sure there is nothing plugged into it.
• Reboot the connected device by reconnecting the device’s power cable.
• Check the cable connections. Make sure a video cable is not connected to an audio input.
• For antenna or Cable connections, check the signal strength. Low signal level may cause sound distortion.
• Perform the Sound Test as explained above.
05 Other Information
English
35
Page 36
Other Information
Issues Solutions and Explanations
No Picture, No Video
The TV won’t turn on. • Make sure the AC power cord is securely plugged in to the wall outlet and the TV.
The TV turns off automatically. • Ensure the Sleep Timer is set to Off in the Setup menu (p. 18).
There is no picture/video. • Check cable connections(remove and reconnect all cables connected to the TV and external devices).
RF(Cable/Antenna) Connection
The TV is not receiving all channels. • Make sure coaxial cable is connected securely.
The picture is distorted: macroblock error, small block, dots, pixelization.
PC Connection
A “Mode Not Supported” message appears.
“PC” is always shown on the source list, even if a PC is not connected.
The video is OK but there is no audio. • If you are using an HDMI connection, check the audio output setting on your PC.
Others
Purple/green rolling horizontal bars and buzzing noise from the TV speakers with Component cable connection.
The remote control does not work. • Replace the remote control batteries with correct the poles (+/–) in the right direction.
• Make sure the wall outlet is working.
• Try pressing the POWER button on the TV to make sure the problem is not the remote. If the TV turns on, refer to “Remote control does not work” below.
• If your PC is connected to the TV, check your PC power settings.
• Make sure the AC power cord is plugged in securely to the wall outlet and the TV.
• When watching TV from an antenna or cable connection, the TV will turn off after 10 - 15 minutes if there is no signal.
• Set your external devices’ (Cable/Sat Box, DVD, Blu-ray etc) video outputs to match the connections to the TV input. For example, if an external device’s output is HDMI, it should be connect to an HDMI input on the TV.
• Make sure your connected devices are powered on.
• Be sure to select the TV’s correct source by pressing the SOURCE button on the remote control.
• Reboot the connected device by reconnecting the device’s power cable.
• Please try Auto Program to add available channels to the channel list. Go to MENU - Channel - Auto Program (p. 12).
• Verify the Antenna is positioned correctly.
• Compression of video contents may cause picture distortion, especially with fast moving pictures such as sports and action movies.
• A low signal can cause picture distortion. This is not a TV problem.
• Set your PC’s output resolution so they match the resolutions supported by the TV (p. 10).
• This is normal; “PC” is always shown on the source list, regardless of whether a PC is connected.
• Remove the left and right audio connections from the set-top-box. If the buzzing stops, this indicates that the set-top-box has a grounding issue. Replace the Component video cables with an HDMI connection.
• Clean the sensor’s transmission window on the remote.
• Try pointing the remote directly at the TV from 5~6 feet away.
36
English
Page 37
Issues Solutions and Explanations
Plasma TV is making humming noise. • Plasma TVs typically make a soft humming sound. This is normal. It’s caused by the electrical charges
Image Retention (Burn In) Issue. • To minimize the possibility of screen burn, this unit is equipped with screen burn reduction technology.
The cable/set top box remote control doesn’t turn the TV on or off, or adjust the volume.
A “Mode Not Supported” message appears.
Caption on TV menu is greyed out. Caption can not be selected in the TV menu when connected via HDMI or Component (p. 18).
There is a plastic smell from the TV. • This smell is normal and will dissipate over time.
The TV is tilted to the side. • Remove the base stand from the TV and reassemble it.
The channel menu is greyed out (unavailable).
Your settings are lost after 30 minutes or every time the TV is turned off.
You have intermittent loss of audio or video.
You may see small particles when you look closely at the edge of the frame of the TV.
that are used to create the images on the screen.
• If the humming sound is loud, you may have set the brightness on the TV too high. Try setting the brightness lower.
• You can also have loud humming if the back of your Plasma TV is too close to a wall or other hard surface. Also try rerouting your connection cables.
• Improper installation of wall mount can create excessive noise.
Pixel Shift technology enables you to set picture movement up/down (Vertical Line) and side to side (Horizontal Dot).
• Program the Cable/Sat remote control to operate the TV. Refer to the Cable/Set user manual for the SAMSUNG TV code.
• Check the supported resolution of the TV, and adjust the external device’s output resolution accordingly. Refer to the resolution settings on page 10 of this manual.
Caption must be activated on the external device (p. 18).
• The Channel menu is only available when the TV source is selected.
• If the TV is in the Store Demo mode, it will reset audio and picture settings every 30 minutes. Change the settings from Store Demo mode to Home Use mode in the Plug & Play procedure. Press the
SOURCE button to select TV mode, and go to MENU Setup Plug & Play ENTER
• Check the cable connections and reconnect them.
• Loss of audio or video can be caused by using overly rigid or thick cables. Make sure the cables are flexible enough for long term use. If mounting the TV to the wall, we recommend using cables with 90 degree connectors.
• This is part of the product’s design and is not a defect.
(p. 7).
05 Other Information
The PIP menu is not available. PIP functionality is only available when you are using a HDMI, PC or Component source.
POP (TV’s internal banner ad) appears on the screen.
Some of above pictures and functions are available at specific models only.
• Select Home Use under Plug & Play mode. For details, refer to Plug & Play Feature (p. 7).
English
37
Page 38
Other Information
Specifications
Environmental Considerations Operating Temperature Operating Humidity Storage Temperature Storage Humidity
Stand Swivel (Left / Right) -20˚ ~ 20˚ Model Name PL42C450 PL50C450 Screen Size 42 inches 50 inches Sound
(Output) 10 W X 2 10 W X 2 Dimensions (WxDxH)
Body With stand
Weight Without Stand With Stand
Panel native 1024 X 768 @ 60Hz 1360 X 768 @ 60Hz
Design and specifications are subject to change without prior notice.
For information about power supply, and more about power consumption, refer to the label attached to the product.
1031 x 70.9 x 631.0 mm
1031 x 284.5 x 695.5 mm
17.5 kg
19.5 kg

License

50°F to 104°F (10°C to 40°C)
10% to 80%. non-condensing
-4°F to 113°F (-20°C to 45°C) 5% to 95%. non-condensing
1202.5 x 69.5 x 720.5 mm
1202.5 x 284.5 x 788 mm
23.4 kg
25.4 kg
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks. & DTS 2.0+ Digital Out and the DTS logos are trademarks of DTS, Inc. Product Includes software. © DTS, Inc. All Rights Reserved.
DivX Certified to play DivX video up to HD 1080p, including premium content.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX,Inc. This is an official DivX Certified device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play DivX Video-on­Demand (VOD) content. To generate the registration code, locate the DivX VOD section in the device setup menu.
Go to vod.divx.com with this code to complete the registration process and learn more about DivX VOD. Pat. 7,295,673; 7,460,688; 7,519,274
Open Source License Notice
In the case of using open source software, Open Source Licenses are available on the product menu. Open Source Licence Notice is written only English.
38
English
Page 39

Index

05 Other Information
A
Amplify 16 Anynet+ 27
AUDIO OUT 9
Auto Adjustment 16 Auto Volume 17
B
Background Music 26 Balance L/R 16 Basic View 26 Batteries 6 Black Tone 14 Blanking Bracket 32 Brightness 13
C
Channel Menu 11 Clock 18 Color Tone 14 Component 8 Connecting to a PC 9 Connecting to an Audio Device 9
D
DIGITAL AUDIO OUT 9, 27
DivX® VOD 26 D-sub 9 Dynamic 13 Dynamic Contrast 14
E
Eco Sensor 14 Edit Name 10 Editing Channels 12 Energy Saving 14 Equalizer 16 External Speaker 17
F
FAV.CH button 6, 12
Favorite Channel 12 Film Mode 15 Fine Tune 13 Flesh Tone 14 FM Transmitter 31 Frequency 10
H
HDMI 8, 27 Home Theater 9, 27
I
Installation Space 33
L
Language 18 License 38 Lock 12
M
Media Play 21 Melody 19 Menu Transparency 19 Mono 17 Music 24
N
Navigate 11
O
Optimal resolution 10
P
Photos 25 Picture Size 14, 26 PIP (Picture in Picture) 19 Plug & Play 7 Power Indicator 5
R
Receiver 29 Recording 29 Remote Control 6 Repeat Mode 26 RGB Only Mode 14 Rotate 26
S
Select All 13 Self Diagnosis 20 Sharpness 13 Sleep Timer 18 Slide Show 25 Software Upgrade 20 Source List 10 Speaker Select 17 Specifications 38 Standby mode 5 Symbol 3
T
Timer 18 Title 26 Tools 3 Troubleshooting 35 TV Speaker 17
U
USB Drive 20, 21
V
Video Formats 23 Videos 23 Virtual Surround 16 Volume 5
W
Wall Mount 32 Warm 14 White Balance 14
English
39
Page 40
Las figuras y las ilustraciones de este Manual del usuario se proporcionan como referencia solamente y pueden ser diferentes del aspecto real del producto. El diseño y las especificaciones del producto están sujetos a cambios sin previo aviso.
Instrucciones para el usuario
Retención de imágenes en la pantalla
No deje imágenes fijas visibles (como las de un videojuego) en el panel de la pantalla de plasma durante mucho tiempo, ya que se podría producir la retención
de la imagen en la misma. Este fenómeno de retención de imágenes también se denomina ‘quemadura de pantalla’. Para evitar dicha retención de la imagen, consulte la página 13 de este manual para reducir el grado de brillo y contraste de la pantalla al mostrar una imagen fija.
Calor en la parte superior del TV de plasma
La parte superior del aparato puede calentarse tras un uso prolongado ya que el calor se disipa desde el panel a través de los orificios de ventilación de la
parte superior del aparato.
Esto es normal y no indica ningún defecto ni fallo de funcionamiento del aparato. No obstante, debe evitarse que los niños toquen la parte superior del aparato.
El aparato emite una especie de ‘crujido’.
El ruido similar a un crujido puede producirse cuando el aparato se contrae o se expande debido a un cambio ambiental de temperatura o humedad. Este
hecho es normal y no se trata de ningún defecto en la unidad.
Defecto de celda
La PDP utiliza un panel compuesto de 2.360.000 píxeles (nivel HD) a 6.221.000 píxeles (nivel FHD) que requieren una sofisticada tecnología para su
producción. No obstante, puede que existan unos cuantos píxeles brillantes u oscuros en la pantalla. Estos píxeles no influirán en el rendimiento del aparato.
Evite que el televisor funcione a temperaturas por debajo de 41°F (5°C)
La imagen fija visualizada durante demasiado tiempo puede causar daños permanentes en el panel de la PDP.
Ver el TV de plasma en formato 4:3 durante un tiempo prolongado puede dejar rastros de bordes en la izquierda, derecha o centro de la pantalla causados por la diferencia de emisión de luz en la pantalla. La reproducción de un DVD o el uso de una consola de videojuegos pueden provocar un efecto similar en la pantalla. Los daños provocados por los efectos mencionados no quedan cubiertos por la garantía.
Imágenes fantasma en la pantalla.
Ver imágenes fijas de videojuegos y PC durante más tiempo del indicado puede producir imágenes fantasma parciales. Para evitar este efecto, reduzca el ‘brillo’ y el ‘contraste’ al mostrar imágenes fijas durante tiempo prolongado.
Garantía
La garantía no cubre ningún daño causado por la retención de imágenes. La garantía no cubre el desgaste de la pantalla.
2
Español
Page 41
Contenido
Introducción
y Listado de características ......................................... 4
y Accesorios ................................................................ 4
y Aspecto general del panel de control ........................5
y Aspecto general del mando a distancia .................... 6
y Conexión de una antena ........................................... 7
y Plug & Play (configuración inicial)............................... 7
Conexiones
y Conexión a un dispositivo AV .................................... 8
y Conexión a un dispositivo de audio ........................... 9
y Conexión a un PC ..................................................... 9
y Cambio de la fuente de entrada .............................. 10
Funciones básicas
y Cómo desplazarse por los menús ........................... 11
y Menú de canales .................................................... 11
Visualización de canales 11 Uso de los canales favoritos 12 Memorización de canales 12 Edición de canales 12 Otras funciones 12
y Menú de la imagen ................................................. 13
Cambio del modo de imagen preseleccionado 13 Ajuste de la configuración de la imagen 13 Soluciones económicas 14 Cambio de las opciones de la imagen 14 Ajuste del televisor con el ordenador 16
y Menú del sonido ..................................................... 16
Cambio del modo de sonido preseleccionado 16 Ajuste de la configuración del sonido 16 Configuración del sonido 16
y Menú de configuración ........................................... 17
Configuración de la hora 17 Uso del temporizador de desconexión 18 Activación y desactivación del temporizador 18 Otras funciones 18 Imagen sobre imagen (PIP) 19
y Menú de asistencia técnica ..................................... 20
Funciones avanzadas
y Media Play .............................................................. 21
Conexión de un dispositivo USB 21 Pantalla de visualización 22 Reproducción de varios archivos 25 Reproductor multimedia - Funciones adicionales 25
y Anynet+ .................................................................. 27
Configuración de Anynet+ 28 Conmutación entre dispositivos Anynet+ 28 Grabación 29 Escucha a través de un receptor 29 Solución de problemas de Anynet+ 30
Información adicional
y Configuración del transmisor FM ............................. 31
Configuración de la frecuencia 31 Guía de instalación del transmisor FM 31 Formatos admitidos por el transmisor FM 32
y Instalación del montaje mural .................................. 32
y Seguridad en el espacio de instalación ................... 33
y Fijación del televisor a la pared ................................ 34
Para impedir que el televisor se caiga 34
y Solución de problemas ........................................... 35
y Especificaciones ..................................................... 38
y Licencia .................................................................. 38
y Índice ...................................................................... 39
ESPAÑOL
¡Compruebe este símbolo!
t
Esta función se puede utilizar pulsando el
botón TOOLS del mando a distancia.
Nota Guía paso a paso
Indica información adicional. Consulte aquí las instrucciones para abrir el
submenú pertinente en la OSD
(on screen display).
Español
3
Page 42

Introducción

Listado de características

y Media Play (USB): Permite reproducir algunos archivos de música e imágenes guardados en un dispositivo USB. (pág. 21) y Autodiagnóstico: Permite comprobar si la imagen o el sonido funciona correctamente. (pág. 20)

Accesorios

Compruebe que los artículos siguientes vengan incluidos con su TV PDP. Si falta alguno, póngase en contacto con su distribuidor.
El color y la forma de los componentes pueden variar según los modelos.
y Mando a distancia y 2 pilas AAA (No está disponible en algunas ubicaciones.) y Manual del usuario y Tarjeta de garantía / Guía de seguridad (No está disponible en algunas ubicaciones.)
y Soporte de protección y Transmisor FM / Brida del transmisor FM (3 unid.)
Cables de entrada (se venden por separado)
y Paño de limpieza y Cable de alimentación
(no disponible en algunos lugares)
HDMI HDMI/DVI Componente Compuesto (AV) Coaxial (RF) VGA
4
Español
Page 43

Aspecto general del panel de control

El color y la forma del producto pueden variar según el modelo.
01 Introducción
Indicador de encendido
Altavoces
SOURCE
MENU Muestra un menú en pantalla, la OSD (on screen display), de las funciones del televisor.

Indicador de encendido Parpadea y se apaga cuando se enciende el aparato y se ilumina en el modo en espera.
Sensor del mando a distancia El mando a distancia debe dirigirse hacia este punto del televisor.
Modo de espera
No deje el televisor en modo de espera durante períodos largos de tiempo (cuando esté de vacaciones, por ejemplo). Aunque esté apagado continúa consumiendo una pequeña cantidad de energía. Se recomienda desconectar el cable de alimentación.
(Encendido)
Cambia entre todas las fuentes de entrada disponibles. En el menú en pantalla, utilice este botón como lo haría con el botón ENTER del mando a distancia.
Ajusta el volumen. En la OSD, utilice los botones y del mando a distancia.
Cambian los canales. En la OSD, utilice los botones y del mando a distancia.
Enciende o apaga el televisor.
Sensor del mando a distancia
de igual modo que los botones
de igual modo que los botones
Español
5
Page 44
Introducción

Aspecto general del mando a distancia

Enciende y apaga el televisor.
Pulse para acceder directamente a los
canales.
No disponible.
Ajusta el volumen.
Hace que aparezca la OSD.
Muestra Media Play (USB) (pág. 21).
Seleccionar rápidamente las funciones que
se usan con mayor frecuencia.
Vuelve al menú anterior.
Utilice estos botones en los menús
Lista de canales, Media Play (USB), etc.
Utilice estos botones en los modos
Media Play (USB) y Anynet+ (HDMI-CEC)
(pág. 21, 27).
(: controla la grabación de las
grabadoras de Samsung con función
Anynet+)
A B C D
S.MODE
P.MODE MTS
FAV.CH
P.SIZE
HDMI
SLEEP
Muestra y selecciona las fuentes de vídeo disponibles (pág. 10).
Vuelve al canal anterior. Corta temporalmente el sonido.
Cambia los canales.
Muestra las listas de canales en la pantalla (pág. 11).
Selecciona directamente el modo HDMI.
Muestra información en la pantalla del televisor.
Selecciona los elementos del menú en pantalla y cambia los valores que aparecen en el menú.
Sale del menú.
S.MODE: Se pulsa para seleccionar el
modo del sonido (pág. 16).
P.MODE: Se pulsa para seleccionar el
modo de la imagen (pág. 13).
MTS : Pulse para elegir estéreo, mono o un
programa de audio independiente (emisión SAP) (pág. 17).
FAV.CH: Muestra la lista de canales
favoritos en la pantalla (pág. 12).
P.SIZE: Selecciona el tamaño de la imagen
(pág. 15).
SLEEP: Apaga automáticamente el
televisor a la hora establecida (pág. 18).
Instalación de las pilas (tamaño de las pilas: AAA)
Español
6
NOTA
Utilice el mando a distancia a menos de 7 metros (23 pies) del televisor.
x
Una luz muy brillante puede afectar al funcionamiento del mando a
x
distancia. No lo utilice cerca de luces fluorescentes o de neón. El color y la forma pueden variar según el modelo.
x
Page 45

Conexión de una antena

POWER
Cuando el televisor se enciende por primera vez, los parámetros básicos se inician de forma automática.
Conexión del cable de alimentación y la antena.
Antena VHF/UHF
Cable
o
Entrada de alimentación
Plug & Play (configuración inicial)
Cuando el televisor se enciende por primera vez, una secuencia de indicaciones en pantalla permite configurar los parámetros básicos. Pulse el botón POWER
Para volver al paso anterior, pulse el botón rojo.
1 2
3 4
. Plug & Play sólo está disponible cuando la fuente Entrada está configurada como TV.
Selección de un idioma
Selección de
Demo comercio o Uso domiciliario
Selección de una antena
Selección de un canal
Ajuste de Reloj Configure Día, Mes, Año, Hora, Minuto o am/pm.
Pulse los botones o y a continuación pulse el botón ENTER el idioma deseado para la OSD (presentación en pantalla).
Pulse los botones o y a continuación pulse el botón ENTER
y Seleccione el modo Uso domiciliario. El modo Demo comercio se utiliza en
los entornos comerciales.
y Recupere la configuración de la unidad desde Demo comercio a
Uso domiciliario (estándar): Pulse el botón del volumen del televisor. Cuando vea la OSD del volumen mantenga pulsado el botón MENU durante 5 segundos.
Pulse los botones o y a continuación pulse el botón ENTER Cable o Aire+Cable.
Pulse los botones o y a continuación pulse el botón ENTER canal que desea memorizar. Al configurar la fuente de la antena en Cable, se muestra un paso que le permite asignar valores numéricos (frecuencias de los canales) a los canales. Para obtener más información, consulte Canal Prog. Auto (pág. 12).
Pulse el botón ENTER en cualquier momento para interrumpir el proceso de memorización.
. Seleccione
.
. Permite seleccionar Aire,
. Seleccione la fuente del
ANT OUT
P
5
Visualización de la
6
Guía de conexión HD. Disfrute de su TV.
Se muestra el modo de conexión para obtener una mejor calidad de pantalla HD.
Pulse el botón ENTER
.
7
01 Introducción
Si desea reiniciar esta función...
MENU Configuración Plug & Play ENTER
Español
7
Page 46

Conexiones

(DVI)
USB
HDMI IN 3
(DVI)

Conexión a un dispositivo AV

Uso de un cable HDMI o HDMI/DVI cable: Conexión HD (hasta 720p/1080i)
Dispositivos disponibles: DVD, reproductor Blu-ray, receptor por cable HD, receptor por satélite HD STB (decodificador).
W
R
Rojo Blanco
HDMI IN 1(DVI), 2, 3, PC/DVI AUDIO IN
Cuando se usa una conexión de cable HDMI/DVI, se debe conectar en el terminal HDMI IN 1(DVI) para vídeo. Es posible que un
x
Dispositivo Dispositivo
HDMI OUT
W R
reproductor de DVD, Blu-ray, receptor por cable HD, receptor por satélite HD STB necesite un cable DVI-HDMI (de DVI a HDMI) o un adaptador DVI-HDMI (de DVI a HDMI). Se necesita el terminal PC/DVI AUDIO IN para el sonido.
Si se conecta un dispositivo externo como un reproductor DVD, Blu-ray, decodificador o receptor por satélite STB que admita versiones
x
HDMI anteriores a 1.3, el televisor quizás no funcione normalmente (por ejemplo, no se muestre la pantalla / no haya sonido/parpadeos molestos / colores anormales).
Si tras conectar un cable HMDI no hay sonido, compruebe la versión HDMI del dispositivo externo. Si sospecha que es una versión
x
anterior a 1.3, póngase en contacto con el proveedor del dispositivo para confirmar la versión de HDMI y solicitar una actualización. Es aconsejable adquirir un cable certificado HDMI. De lo contrario, la pantalla puede aparecer vacía o producirse un error de conexión.
x
Uso de un cable de componentes (hasta 720p/1080i) o audio/vídeo (sólo 480i)
Dispositivos disponibles: Reproductor VCR, DVD, Blu-ray, decodificador, receptor por satélite STB
DVI OUT
AUDIO OUT
R-AUDIO-L
W
R
Rojo Blanco Rojo Azul Verde Rojo Blanco Amarillo
Cuando se conecta a AV IN 1 el color (verde) del terminal AV IN 1 [Y/VIDEO] no coincide con el cable de vídeo (amarillo).
Para obtener la mejor calidad de imagen, se recomienda la conexión de componentes antes que la conexión A/V.
Español
8
R GB
W
R
R
Dispositivo
AUDIO OUT
R-AUDIO-L
W
R GB
R B G
COMPONENT OUT
PR PB Y
Dispositivo
AUDIO OUT
R-AUDIO-L
R W
Y
Y
WR
Y
WR
VIDEO OUT
Page 47

Conexión a un dispositivo de audio

(DVI)
R-AUDIO-L
Uso de una conexión de cable óptico (digital) o de audio (analógico)
Dispositivos disponibles: Sistema de audio digital, Amplificador, Sistema Home Theater DVD
W
R
Rojo Blanco
DIGITAL AUDIO OUT (OPTICAL)
Cuando un sistema de audio digital se conecta al terminal DIGITAL AUDIO OUT (OPTICAL), se reduce el volumen del televisor y del
x
sistema. El audio de 5.1 canales está disponible cuando el televisor se conecta a un dispositivo externo que admite audio de 5.1 canales.
x
Cuando el receptor (amplificador o sistema Home Theater DVD) está encendido, se puede oír la salida de sonido del terminal óptico del
x
televisor. Cuando el televisor recibe una señal DTV, envía el sonido de 5.1 canales al amplificador o sistema Home Theater DVD. Cuando la fuente es un componente digital, como un reproductor DVD / Blu-Ray / receptor de cable o satélite (decodificador), y está conectada al televisor a través de HDMI, sólo se oye el sonido de 2 canales del amplificador o del sistema Home Theater DVD. Si desea oír el audio de 5.1 canales, conecte el terminal de la salida de audio digital del reproductor DVD / Blu-ray / decodificador / receptor por satélite STB directamente al amplificador o al sistema Home Theater.
AUDIO OUT: Permite conectar los terminales de la entrada de audio del amplificador/sistema Home Theater.
En la conexión, utilice el conector apropiado.
x
Cuando un amplificador de audio se conecta a los terminales AUDIO OUT: Reduzca el volumen del televisor y ajuste el volumen con el
x
control de volumen del amplificador.
02 Conexiones
Sistema de audio digital
OPTICAL
Amplificador / DVD para Home Theater
AUDIO IN
Uso de cables
HDMI/DVI cable o D-sub cable

Conexión a un PC

AUDIO OUT
DVI OUT
AUDIO OUT
PC OUT
Español
9
Page 48
Conexiones
SOURCE
Modos de visualización (entradas D-Sub y HDMI/DVI)
Resolución óptima
y 42": 1024 x 768 a 60Hz y 50": 1360 x 768 a 60Hz
Modo Resolución
IBM
MAC
VESA CVT
VESA DMT
VESA GTF
640 x 350 720 x 400
640 x 480 832 x 624
720 x 576
1280 x 720
640 x 480 640 x 480 640 x 480 800 x 600 800 x 600
800 x 600 1024 x 768 1024 x 768 1024 x 768 1280 x 720 1360 x 768
1280 x 720 52.500 70.000 89.040 -/+
Frecuencia
horizontal
(KHz)
31.469
31.469
35.000
49.726
35.910
56.456
31.469
37.500
37.861
37.879
46.875
48.077
48.363
56.476
60.023
45.000
47.712
NOTA
En una conexión de cable HDMI/DVI, se debe utilizar el terminal HDMI IN 1(DVI).
x
No se admite el modo entrelazado.
x
El aparato puede funcionar incorrectamente si se selecciona un formato de vídeo que no sea estándar.
x
Los modos Independiente y Compuesto no se admiten. SOG (Sync On Green) no se admite.
x
Frecuencia
vertical
(Hz)
70.086
70.087
66.667
74.551
59.950
74.777
59.940
75.000
72.809
60.317
75.000
72.188
60.004
70.069
75.029
60.000
60.015
Frecuencia de
reloj de píxeles
(MHz)
25.175
28.322
30.240
57.284
32.750
95.750
25.175
31.500
31.500
40.000
49.500
50.000
65.000
75.000
78.750
74.250
85.500
Polaridad de
sincronización
(H/V)
+/-
-/+
-/-
-/-
-/+
-/+
-/-
-/-
-/­+/+ +/+ +/+
-/-
-/­+/+ +/+ +/+
42
"
 
 
        
50
 
 
 
         
"

Cambio de la fuente de entrada

Lista de fuentes
Se utiliza para seleccionar TV u otras fuentes de entrada externas como reproductores de DVD / Blu-ray / decodificadores o receptores por satélite STB.
MENU Entrada
Lista de Entradas ENTER
TV / PC / AV1 / AV2 / Componente1 / Componente2 / HDMI1/DVI / HDMI2 / HDMI3 / USB
Puede elegir solamente dispositivos externos que estén conectados al televisor. En Lista de Entradas, se resaltan las entradas conectadas.
En Lista de Entradas, PC siempre está activado.
Español
10
Editar Nombre
MENU Entrada Editar Nombre ENTER
Vídeo / DVD / Cable STB / Satélite STB / PVR STB / Receptor AV / Juego / Filmadora / PC / DVI PC / Dispositivos DVI / TV / IPTV / Blu-ray / HD DVD / DMA: Dé
un nombre al dispositivo conectado en las tomas de entrada; de esta manera será más fácil seleccionar el dispositivo de entrada.
Cuando se conecta un cable HDMI/DVI al puerto HDMI IN 1(DVI), se debe configurar el puerto en el modo DVI PC o Dispositivos DVI en Editar Nombre.
Page 49

Funciones básicas

CH LIST

Cómo desplazarse por los menús

Antes de usar el televisor, siga los pasos siguientes para conocer cómo explorar el menú y seleccionar y ajustar las diversas funciones.

Menú de canales

03 Funciones básicas
 Visualización de canales
1
2
3 4
1 Botón MENU: Muestra el menú principal en pantalla. 2 Botones ENTER
seleccione una opción. Confirme la configuración.
3 Botón RETURN: Vuelve al menú anterior. 4 Botón EXIT: Sale del menú en pantalla.
Funcionamiento de la OSD (presentación en pantalla)
El procedimiento de acceso puede variar según el menú seleccionado.
MENU
1
/
2
ENTER
3
/
4
/
5
ENTER
6
EXIT

/ direccionales: Mueva el cursor y
Las opciones del menú principal se muestran en la pantalla:
Imagen, Sonido, Canal, Configuración, Entrada, Aplicaciones, Soporte técnico.
Seleccione un icono con los botones o .
Pulse ENTER para acceder al menú secundario.
Seleccione un menú secundario con los botones o .
Ajuste el valor de un elemento con los botones o . El ajuste de la visualización en pantalla puede variar según el menú seleccionado.
Pulse ENTER para confirmar una selección.
Pulse EXIT.
7
Lista de canales
Añadir, borrar o establecer los canales favoritos y usar la guía de programas de las emisiones digitales.
MENU Canal Lista de canales ENTER
Seleccione un canal en la pantalla Todos los canales, Canales agregados, Favoritos o Grabación con temporizador mediante la pulsación de los botones
/ y pulse el botón ENTER. A continuación puede ver el canal seleccionado.
Canales agregados
Todos los canales : Muestra todos los canales disponibles actualmente.

Grabación con temporizador : Muestra todos los
programas actualmente reservados.
Uso de los botones de colores con el Lista de canales
x x x
Seleccione los canales que desee y pulse el botón amarillo para configurar todos los canales seleccionados al mismo tiempo. La marca  aparece a la izquierda de los canales seleccionados.
x
x
Lista de canales. (Los menús de las opciones pueden cambiar, dependiendo de la situación.)
Iconos de la pantalla de estado del canal
3 Aire
4 Aire
5 * Aire 6 Aire 7 Aire
8 Aire 9 Aire 10 Aire
Aire Antena Zoom Seleccionar  Página
Canales agregados : Muestra todos los canales añadidos. Favoritos : Muestra todos los canales favoritos.
Rojo (Antena): Cambia a Aire o Cable. Verde (Zoom): Aumenta o disminuye el número del canal. Amarillo (Seleccionar): Selecciona varias listas de canales.
(Página): Vaya a la página siguiente o anterior.
(Herramientas): Muestra el menú de opciones

Herramientas
Iconos Función
Canal seleccionado.
Canal configurado como favorito.
Programa reservado.
Canal bloqueado.
Español
11
Page 50
Funciones básicas
 Uso de los canales favoritos
MENU Canal Lista de canales ENTER
Agregar a Favoritos / Borrar de Favoritos
Configure los canales que vea con más frecuencia como favoritos.
1. Seleccione un canal y pulse el botón TOOLS.
2. Añada o borre un canal mediante el menú Agregar a Favoritos o Borrar de Favoritos, respectivamente.
 Edición de canales
Edición de nombre de canal
1. Seleccione un canal y pulse el botón TOOLS.
2. Edite el nombre del canal mediante el menú
Edición de nombre de canal: Asigne un nombre de canal
 Otras funciones
Canales agregados
Para que aparezcan todos los canales favoritos, haga clic en el botón que se muestra a la derecha.
3 Aire
4 Aire
5 * Aire 6 Aire 7 Aire
8 Aire 9 Aire 10 Aire
Aire Antena Zoom Seleccionar  Página
Borrar
Agregar a Favoritos
Bloquear
Visual. tempor.
Edición de nombre de canal
Seleccionar todo

Herramientas
FAV.CH
Lista de canales
Menú de opciones del administrador de canales
Establezca cada canal mediante las opciones del menú Lista de canales (Añadir / Borrar, Bloquear / Desbloquear, Visual. tempor., Seleccionar todo / Deseleccionar todos). Los elementos del menú de opciones pueden variar según el estado del canal.
1. Seleccione un canal y pulse el botón TOOLS.
2. Seleccione una función y cambie la configuración.
Añadir / Borrar: Suprima o añada un canal para que se
 Memorización de canales
MENU Canal ENTER
Antena (Aire / Cable)
Antes de que el televisor empiece a memorizar los canales disponibles, debe indicar el tipo de origen de la señal conectada al televisor (es decir, Aire o Cable).
Bloquear / Desbloquear: Se puede bloquear un canal para
Prog. Auto
Aire : Señal de antena aérea.
Cable : Señal de antena del cable.
Aire+Cable: Air and Cable antenna signals.
Si desea detener la programación automática, pulse el botón
ENTER. Aparece el mensaje ¿Detener programación
automática?. Seleccione Si con los botones or , a
continuación, pulse el botón ENTER.
Visual. tempor.: Se puede establecer que el canal que se
MENU Canal Lista de canales ENTER
Edición de nombre de canal.
personal.
MENU Canal ENTER
muestren los canales que desee.
NOTA
Todos los canales borrados se mostrarán en el menú
x
Todos los canales. Un canal de color gris quiere decir que se ha suprimido.
x
El menú Añadir sólo aparece con los canales borrados.
x
Suprima un canal del menú Canales agregados o
x
Favoritos de la misma manera.
que no se pueda seleccionar ni visualizar.
Está función está disponible sólo cuando Bloqueo está configurado como Encendido.
Aparece la pantalla para la introducción del número PIN. Escriba un número de 4 dígitos, el predeterminado es “0-0-0­0”. Cambie el PIN mediante la opción Cambiar Código.
desee se muestre automáticamente a una hora reservada. Para utilizar esta función, en primer lugar configure la hora actual.
1. Pulse los botones /// para seleccionar el canal que desee en la Lista de canales.
2. Pulse el botón TOOLS y seleccione Visual. tempor..
12
Español
Page 51
3. Desplácese arriba o abajo para ajustar la configuración
en la caja o utilice los botones numéricos del mando a distancia para introducir la fecha y la hora.
Si selecciona Una vez, Cada semana o Cada día en
Repetir, puede introducir la fecha que desee.
4. Seleccione Aceptar y pulse el botón ENTER cuando
haya terminado.
NOTA
Sólo se pueden reservar los canales memorizados.
x
Los programas reservados se mostrarán en el menú
x
Grabación con temporizador.
Seleccionar todo : Seleccione todos los canales de la lista.
Deseleccionar todos : Se cancelan todas las selecciones de
canales.
Sólo se puede seleccionar Deseleccionar todos si hay uno o más canales seleccionados.
Sistema Color (Auto / PAL-M / PAL-N / NTSC)
Normalmente el televisor puede recibir imagen y sonido de buena calidad en el modo Automático. Este modo detecta automáticamente el sistema de color de la señal. Si recibe un sistema de señal con un color insatisfactorio, establezca el modo de sistema de color en PAL-M, PAL-N o NTSC.
Modo
Seleccione el tipo de imagen preferido.
Dinámico: Adecuado para un entorno
Grabación con temporizador
(en Lista de canales) Puede ver, modificar o borrar un programa que haya reservado para
ver. El temporizador de Grabación con temporizador se muestra aquí. Resalte un programa y pulse el botón TOOLS para mostrar las opciones.
Cambiar información: Cambie un programa que haya
reservado para ver. Comience en el paso 3 de “Visual. tempor.” anterior.
Cancelar programaciones: Cancele un programa que haya
reservado para ver.
Así se borran los programas resaltados o seleccionados.
Información: Muestre un programa que haya reservado para
ver. (También se puede cambiar la información de reserva.) También puede ver la información resaltando un programa y pulsando el botón ENTER.
Seleccionar todo / Deseleccionar todos: Seleccione o
deseleccione todos los programas reservados.
Normal: Adecuado para un entorno normal.
Cine: Adecuado para ver películas en un
Luz de la celda / Contraste / Brillo / Definición / Color / Tinte (V/R)
El televisor tiene diferentes opciones de configuración para controlar la calidad de la imagen.
Sintonia Fina
Si la recepción es clara, no tiene que realizar la sintonización fina del canal, ya que esta operación se hace de forma automática durante la búsqueda y la memorización. Si la señal es débil o está distorsionada, realice manualmente la sintonización fina del canal. Desplácese a izquierda o derecha hasta que la imagen se vea clara.
La configuración se aplica al canal que se está viendo.
Los canales que se han ajustado con sintonización fina se marcan con un asterisco “*” a la derecha del número de canal en la banda del canal.
Para reiniciar la sintonía fina, seleccione Reiniciar.

Menú de la imagen

 Cambio del modo de imagen preseleccionado
MENU Imagen Modo ENTER
P.MODE
iluminado.
entorno oscuro.
 Ajuste de la configuración de la imagen
MENU Imagen ENTER
NOTA
Cuando haga cambios en Luz de la celda, Contraste, Brillo,
x
Definición, Color o Tinte (V/R), la OSD también se ajustará. En el modo PC, sólo se pueden realizar cambios en las opciones
x
Luz de la celda, Contraste y Brillo. La configuración de cada dispositivo externo conectado al
x
televisor se puede ajustar y guardar.
03 Funciones básicas
Español
13
Page 52
Funciones básicas
 Soluciones económicas
MENU Imagen Solución Eco ENTER
La función ecológica se puede utilizar para mejorar el ahorro de energía.
Solución económica
Ahorro energía (Apagado / Bajo / Medio / Alto / Imag. desact.)
del televisor, lo cual reduce el consumo de energía. Si se selecciona Imag. desact., la pantalla se apaga, pero se oye el sonido. Pulse cualquier botón, excepto el del volumen, para encender la pantalla. Mientras la pantalla se vuelve a encender, se mostrará una imagen distorsionada durante aproximadamente 4 segundos.
Sensor Eco (Apagado / Encendido): Para mejorar el ahorro de energía, la configuración de la imagen se adapta automáticamente a la iluminación de la habitación.
Luz mín celular: Cuando Sensor Eco está configurado como Encendido, el brillo mínimo de la pantalla se puede ajustar
manualmente.
Espera sin señal (Apagado / 15 min. / 30 min. / 60 min.): Para evitar un consumo de energía innecesario, establezca cuánto tiempo desea que el televisor permanezca encendido si no recibe ninguna señal.

Cambio de las opciones de la imagen

Si se ajusta la Luz de la celda, el Sensor Eco se debe establecer como Apagado.
Si el Sensor Eco está configurado como Encendido, el brillo de la pantalla puede cambiar (ligeramente más oscuro o más brillante) según la intensidad de la iluminación del entorno.
Deshabilitado cuando el PC está en el modo de ahorro de energía.
: De este modo se ajusta el brillo
Configuración avanzada
MENU Imagen Configuración avanzada ENTER
(La configuración avanzada está disponible en los modos Normal / Cine) Si se comparan con los modelos anteriores, los nuevos televisores
de Samsung muestran una imagen más precisa.
En el modo PC, sólo se pueden cambiar Contraste Dinám., Gamma y Balance de blanco.
Conguración avanzada
Tono del negro : Apagado
Contraste Dinám. : Medio
Gamma : 0
Modo Sólo RGB : Apagado
Espacio de color : Nativo
Balance de blanco
Tono Piel : 0
Mover

Enter

Regresar
Tono del negro (Apagado / Oscuro / Más oscuro / El más oscuro): Seleccione el nivel de negro para ajustar la
profundidad de la pantalla.
Contraste Dinám. (Apagado / Bajo / Medio / Alto): Ajuste el contraste de la pantalla.
Gamma: Ajuste la intensidad del color primario.
Modo Sólo RGB (Apagado / Rojo / Verde / Azul): Muestra los colores Rojo, Verde y Azul para afinar los ajustes del tono y la saturación.
Espacio de color (Auto / Nativo): Ajuste la gama de colores disponibles para crear la imagen.
Balance de blanco: Ajuste la temperatura del color para obtener una imagen más natural.
Bal. Rojo / Bal. Verde / Bal. Azul: Ajuste la intensidad de cada color (rojo, verde, azul).
Gan. Rojo / Gan. Verde / Gan. Azul: Ajuste el brillo de cada color (rojo, verde, azul).
Reiniciar: Restablece los valores predeterminados de Balance de blanco.
Tono Piel: Mejore el tono rosado de la piel.
Mejora de perfiles (Apagado / Encendido): Mejora los bordes del objeto.
Opciones de imagen
MENU Imagen Opciones de imagen ENTER
En el modo PC sólo se pueden cambiar Tono Color, Tamaño y Protección de pantalla.
Opciones de imagen
Tono Color : Normal
Tamaño : 16:9
Filtro dig. de ruido : Auto
Filtro de ruido MPEG : Auto
Nivel de negro HDMI : Normal
Modo película : Apagado
Protección de pantalla
Mover

Enter

Regresar
Tono Color (Frío / Normal / Tibio1 / Tibio2)
Tibio1 o Tibio1 se desactivan cuando el modo de imagen es Dinámico.
La configuración de cada dispositivo externo conectado a una entrada del televisor se puede ajustar y guardar.
Tamaño: Es posible que el receptor de satélite o cable tenga también su propia gama de tamaños de pantalla. Sin embargo, es muy aconsejable utilizar el modo 16:9 la mayoría de las veces.
P.SIZE
14
Español
Page 53
16:9 : Ajusta la imagen al modo panorámico 16:9. Zoom1 : Permite una ampliación moderada. Zoom2 : Permite una ampliación más potente. Ajuste ancho : Amplía la relación de aspecto de la imagen
para que se ajuste al ancho total de la pantalla.
Disponible para las señales HD 1080i/720p en el modo 16:9.
4:3 : Ajusta la imagen al modo básico (4:3).
No vea la televisión en formato 4:3 durante largos periodos de tiempo. Los rastros de bordes a la izquierda, derecha o centro de la pantalla pueden provocar un desgaste de la pantalla por la retención de la imagen que no está cubierto por la garantía.
Ajuste pantalla : Muestra la imagen completa sin cortes cuando la entrada de la señal es HDMI (720p/1080i/1080p) o Componente (1080i/1080p).
NOTA
Después de seleccionar Zoom1, Zoom2 o Ajuste ancho :
x
1. Pulse el botón para seleccionar Posición.
2. Pulse el botón ENTER
3. Pulse los botones o para desplazar la imagen
hacia arriba o hacia abajo.
4. Pulse el botón ENTER
5. Pulse el botón para seleccionar Rein..
6. Pulse el botón ENTER
posición predeterminada.
Después de seleccionar Ajuste pantalla en los modos HDMI
x
(1080i/1080p) o Componente (1080i/1080p), quizá deba centrar la imagen:
1. Pulse los botones o para seleccionar Posición.
2. Pulse el botón ENTER
3. Pulse los botones , , o para mover la imagen.
4. Pulse el botón ENTER
5. Pulse los botones o para seleccionar Rein..
6. Pulse el botón ENTER
HD (alta definición): 16:9 - 1080i/1080p (1920x1080), 720p
x
(1280x720) La configuración de cada dispositivo externo conectado a una
x
entrada del televisor se puede ajustar y guardar.
Fuente entrada Tamaño de imagen
TV, AV, Component (480i, 480p) 16:9, Zoom1,
Componente (1080i, 1080p), HDMI (720p, 1080i, 1080p)
PC 16:9, 4:3
.
.
para devolver a la imagen su
.
.
.
Zoom2, 4:3 16:9, Ajuste ancho,
4:3, Ajuste pantalla
Filtro dig. de ruido (Apagado / Bajo / Medio / Alto / Auto / Visualiz. automática / Demo): Si la señal de emisión que
recibe el televisor es débil, puede activarse la función Filtro dig. de ruido para reducir la estática y las imágenes superpuestas que pueden aparecer en la pantalla.
Cuando la señal sea débil, intente otras opciones hasta que se vea una imagen de mejor calidad.
Visualiz. automática: Cuando se cambian los canales analógicos, muestra la intensidad de la señal actual y define el filtro del ruido de la pantalla.
Una barra verde indica que es la mejor señal posible.
Filtro de ruido MPEG (Apagado / Bajo / Medio / Alto / Auto): Reduce el ruido MPEG para proporcionar una mejor calidad de imagen.
Nivel de negro HDMI (Normal / Bajo): Selecciona el nivel de negro en la pantalla para ajustar la profundidad de ésta.
Disponible sólo en el modo HDMI.
Modo película (Apagado / Auto1 / Auto2): Configura el televisor para detectar automáticamente y procesar las señales de las películas procedentes de todas las fuentes, y ajusta la imagen para conseguir una calidad óptima.
Disponible en TV, AV, COMPONENT (480i/1080i) y HDMI(480i/1080i).
Protección de pantalla: Esta pantalla está equipada con tecnología de prevención para reducir la posibilidad de que se queme. El ajuste de tiempo permite programar intervalos temporales entre los movimientos de la imagen en minutos.
Cambio de píxel (Apagado / Encendido): Con esta función podrá mover píxeles de forma detallada en la pantalla PDP, en sentido horizontal o vertical, para minimizar restos de imágenes en la pantalla.
Condición óptima para cambio de píxel
Elemento
Horizontal 0~4 4
Vertical 0~4 4
Hora (minutos) 1~4 min. 4 min.
El valor Cambio de píxel puede variar según el tamaño (pulgadas) del monitor y el modo.
Esta función no está disponible en el modo Ajuste pantalla.
Tpo. protección auto. (10 min. / 20 min. / 40 min. / 1 hour / Apagado) : Establece el tiempo en que la pantalla
permanece inactiva con una imagen fija hasta que se activa el salvapantallas. El salvapantallas evita la formación de imágenes superpuestas en la pantalla.
TV/AV/Componente/
HDMI/PC
03 Funciones básicas
Español
15
Page 54
Funciones básicas
Desplazamiento: Esta función suprime los restos de imágenes en la pantalla moviendo todos los píxeles del PDP de acuerdo con un patrón. Utilice esta función si hay restos de imágenes o símbolos en la pantalla, especialmente después de haber mostrado una imagen fija en la pantalla durante un largo tiempo.
La función de supresión de restos de imágenes debe aplicarse durante largo tiempo (aproximadamente 1 hora) para que sea efectiva. Si los restos de imágenes no desaparecen después de ejecutar la función, repita el proceso.
Pulse cualquier tecla del mando a distancia para cancelar esta función.
Lateral gris (Claro / Oscuro): Cuando se ve la televisión con una relación de pantalla establecida en 4:3, ésta se puede proteger de un posible daño si se ajusta el balance de blanco en ambos extremos, el izquierdo y el derecho.
Reinicio de la imagen (Aceptar / Cancelar)
Restablece la configuración predeterminada del modo de la imagen actual.
3. Haga clic en “Pantalla” y aparecerá una cuadro de diálogo
4. Seleccione la ficha “Configuración” en el cuadro de diálogo.
 Cambio del modo de sonido preseleccionado
Modo
Normal: Selecciona el modo de sonido
 Ajuste del televisor con el ordenador
Defina la fuente de entrada al PC.
MENU Imagen ENTER
Ajuste Automático
Ajuste automáticamente los valores y las posiciones de la frecuencia y afine la configuración.
No disponible en las conexiones a través del cable HDMI/DVI.
Música: Refuerza la música por encima de
Cine: Ofrece el mejor sonido para películas.
Voz clara: Realza las voces respecto de los
Amplificar: Aumenta la intensidad del sonido de alta frecuencia
 Ajuste de la configuración del sonido
Pantalla
Grueso / Fino: Elimina o reduce el ruido de la imagen. Si el ruido
no desaparece sólo con la sintonización fina, realice los ajustes de frecuencia hasta el máximo (Grueso) y vuelva a realizar la sintonización fina. Después de reducir el ruido, vuelva a ajustar la imagen para que quede alineada en el centro de la pantalla.
Posición: Ajuste la posición de la pantalla del PC si no se acopla
a la pantalla del TV. Pulse los botones o para ajustar la posición vertical. Pulse los botones o para ajustar la posición horizontal.
Reiniciar Imagen: Restablece la configuración predeterminada
de la imagen.
Uso del televisor como una pantalla de ordenador (PC)
Configuración del software del PC (basado en Windows XP) Según la versión de Windows y la tarjeta de vídeo, las pantallas
reales del PC pueden ser diferentes, pero se aplicará casi siempre la misma información de configuración básica. (En caso contrario, póngase en contacto con el fabricante del ordenador o con el distribuidor de Samsung.)
1. Haga clic en "Panel de control" en el menú de inicio de Windows.
2. Haga clic en "Apariencia y temas" en la ventana "Panel de
control" y aparecerá un cuadro de diálogo.
Ecualizador
Ajusta el modo de sonido (sólo modo de sonido estándar).
Balance I/D: Ajusta el balance entre los altavoces izquierdo y
100Hz / 300Hz / 1kHz / 3kHz / 10kHz (ajuste de ancho de
Reiniciar: Restablece la configuración del ecualizador.
 Configuración del sonido
Virtual Surround (Apagado / Encendido)
(sólo modo de sonido estándar) Esta función proporciona una sensación de sonido surround
virtual de 5.1 canales a través de un par de altavoces mediante la tecnología HRTF (función de transferencia relativa a la cabeza).
sobre la pantalla.
– Configuración correcta del tamaño (resolución)
[Óptima: 42": 1024 X 768 / 50": 1360 x 768 píxeles]
– Si existe una opción de frecuencia vertical en el cuadro de
diálogo de configuración de la pantalla, el valor correcto es ‘60’ o ‘60 Hz’. En caso contrario, haga clic en ‘Aceptar’ y salga del cuadro de diálogo.

Menú del sonido

MENU Sonido Modo →ENTER
normal.
las voces.
sonidos.
para permitir una mejor audición a las personas con problemas de audición.
MENU Sonido Ecualizador ENTER
derecho.
banda): Ajusta el nivel de frecuencias específicas de ancho de banda.
S.MODE
16
Español
Page 55
Claridad diálogo (Apagado / Encendido)
(sólo modo de sonido estándar) Esta función permite aumentar la intensidad de las voces por
encima de la música de fondo o los efectos de sonido a fin de que el diálogo se pueda oír más claramente.
Salida de SPDIF
SPDIF (Interfaz digital de Sony Philips) se utiliza para proporcionar sonido digital, mediante la reducción de las interferencias entre los altavoces y los distintos dispositivos digitales, como un receptor de A/V o Home Theater.
Formato de audio: Durante la recepción de una emisión de
Idioma preferido
(sólo canales digitales) El sistema de emisión de TV digital permite
transmitir simultáneamente muchas pistas de audio (por ejemplo, traducciones simultáneas del programa en otros idiomas).
No disponible en algunos lugares.
Sólo se puede seleccionar uno de los idiomas que ofrece la emisora.
Sonid Multi-track (MTS)
Mono : Elija para canales que emiten en
monoaural o si tiene dificultades con la recepción de señales estéreo.
Estéreo : Elija para canales que emiten en
estéreo.
SAP : Elija esta opción para escuchar el
programa de audio independiente, que normalmente es una traducción de otro idioma.
En función del programa concreto que se emita, puede escuchar en modo Mono, Estéreo o SAP.
MTS
MTS
Retraso de audio: Corrija los problemas de sincronización
Transmisor FM
(Not available in some locations) Puede escuchar en el TV el sonido del altavoz del receptor FM
transmitiendo las señales de audio por frecuencias FM.
Conexión del transmisor FM
Inserte el módulo del transmisor FM en el conector de la parte posterior del televisor.
TV digital se puede seleccionar el formato de salida de audio digital (SPDIF) entre las opciones PCM o Dolby Digital.
entre audio y vídeo, cuando vea la televisión o un vídeo, y cuando escuche un salida de audio digital mediante un dispositivo externo, como un receptor AV (0ms ~ 250ms).
Si desea más información, consulte “Configuración del transmisor FM” (pág. 31).
Panel lateral del TV
03 Funciones básicas
Vol.Auto (Apagado / Normal / Noche)
Para equilibrar el nivel del volumen de cada canal, se ha de configurar como Normal.
Noche: Este modo proporciona una sensación de sonido mejorada en comparación al modo Normal, ya que casi no se produce ruido. Es útil por la noche.
Seleccionar altavoz (Altavoz externo / Altavoz de TV)
Debido a las diferencias en la velocidad de decodificación entre el altavoz principal y el receptor de audio se puede originar un eco. En tales casos, establezca TV como Altavoz externo.
Cuando Seleccionar altavoz está establecido como Altavoz externo, los botones de volumen y MUTE no funcionan y se limita la configuración del sonido.
Compruebe si Seleccionar altavoz está establecido como
Altavoz externo.
Altavoz de TV: Apagado, Altavoz externo: Encendido
x
Compruebe si Seleccionar altavoz está establecido como
Altavoz de TV.
Altavoz de TV: Encendido, Altavoz externo: Encendido
x
Si no hay señal de vídeo, ambos altavoces se silencian.
Reinicio del sonido (Aceptar / Cancelar)
Restablezca todas las configuraciones de sonido predeterminadas de fábrica.
Hora
Transmisor FM
Transmisor FM (Apagado / Encendido): Apaga o enciende el
transmisor FM.
FM Frequency: Establece la frecuencia del transmisor FM.
Menú de configuración
 Configuración de la hora
MENU Configuración Hora ENTER
Hora: La configuración del reloj se utiliza en diferentes
funciones del temporizador del televisor.
La hora actual aparecerá siempre que se pulse el botón INFO.
Español
17
Page 56
Funciones básicas
Si desconecta el cable de alimentación, debe configurar el reloj de nuevo.
Reloj: Configure manualmente Día, Mes, Año, Hora, Minuto y am/pm.
Puede ajustar el Día, Mes, Año, Hora y Minuto directamente pulsando los botones numéricos del mando a distancia.
 Uso del temporizador de desconexión
MENU Configuración Hora Temporizador ENTER
Temporizador: Apaga automáticamente el televisor tras un periodo de tiempo establecido. (30, 60, 90, 120, 150 y 180 minutos).
Para cancelar Temporizador seleccione
Apagado.
 Activación y desactivación del temporizador
MENU Configuración Hora Temporizador 1 ENTER
Puede ajustar el TV para que se encienda automáticamente a la hora prefijada.
Temporizador 1 / Temporizador 2 / Temporizador 3: La activación y desactivación del temporizador se puede configurar de tres maneras.
Debe ajustar el reloj en primer lugar.
Hora encendido
Inactivo
Hora apagado
Inactivo
Volumen
Repetir
Una vez
Hora de encendido / Hora de apagado: Puede configurar la hora y los minutos y activar o desactivar el temporizador. (Para activar el temporizador con la configuración deseada, establézcalo en Activar.)
Volumen: Configure el nivel de volumen deseado. Origen: Seleccione el contenido TV o USB que se ha de reproducir cuando
el televisor se encienda automáticamente. (USB se puede seleccionar sólo cuando el dispositivo USB está conectado al televisor)
Antena (cuando Origen está configurado como TV): Seleccione Aire o Cable.
Canal (cuando Origen está configurado como TV): Seleccione el canal
deseado. Contenido (cuando Origen está configurado como USB): Seleccione una
carpeta en el dispositivo USB que contenga archivos de música o de fotos que se han de reproducir cuando el televisor se encienda automáticamente.
Temporizador 1
00 00 am
00 00 am
Origen
Dom Lun Mar Mié Jue Vie Sáb
Antena Canal
TV20 3
Mover

Ajustar
Aire

Entrar

SLEEP
Regresar
Idioma del menú
Ajuste el idioma de los menús.
1. Seleccione Idioma del menú y pulse el botón ENTER
2. Seleccione el idioma que desee y pulse el botón ENTER
Subtítulos
(Mensajes de texto en pantalla)
Subtítulo (Apagado / Encendido): Puede activar o desactivar
Modo de Subtítulo : Puede seleccionar el modo de subtítulo
NOTA
Si no hay archivos de música en el dispositivo USB o no se ha
x
seleccionado la carpeta que contenga los archivos de música, el temporizador no funciona correctamente.
Si sólo hay un archivo de fotos en el USB, la presentación no
x
se reproducirá. Si el nombre de la carpeta es demasiado largo, ésta no se
x
seleccionará. Cada USB que se utiliza está asignado a su propia carpeta.
x
Cuando se utiliza más de un mismo tipo de USB, asegúrese de que la carpeta asignada a cada dispositivo USB tenga un nombre diferente.
Repetir: Seleccione Una vez, Cada día, Lun~Vie, Lun~Sáb, Sáb~Dom o Manual para configurarlo como más le convenga. Si selecciona Manual, puede configurar el día en que desee activar el temporizador.
La marca indica que se ha seleccionado el día.
Apagado automático (sólo disponible cuando el televisor se ha encendido con el temporizador): El televisor se apagará automáticamente 3 horas después de que se haya dejado inactivo para prevenir un sobrecalentamiento.
 Otras funciones
MENU Configuración ENTER
la función de subtítulos. Si los subtítulos no están disponibles, no se mostrarán en la pantalla.
La función de subtítulos no está disponible en los modos Componente, HDMI ni PC.
deseado.
La disponibilidad de los subtítulos depende del programa que se esté emitiendo.
CC1~CC4 / Texto1~Texto4: La función de subtítulos analógicos funciona tanto en el modo de canal de televisión analógica como cuando la señal se dirige de un dispositivo externo al televisor.
Servicio1~Servicio6 / CC1~CC4 / Texto1~Texto4: (sólo canales digitales) La función de subtítulos digitales funciona con canales digitales.
No disponible en algunos lugares.
.
.
18
Español
Page 57
Es posible que Servicio 1~6 no estén disponibles en el modo de subtítulos digitales según el tipo de emisión.
Opciones - Subtítulos Dig.: (sólo canales digitales)
No disponible en algunos lugares.
Tamaño : Las opciones incluyen Programado, Pequeño, Normal y Grande. El valor predeterminado es Normal.
Estilo fuente: Las opciones incluyen Programado y Estilo del 0 al 7. El valor predeterminado es Estilo0.
Color de primer plano: Las opciones incluyen Programado, Blanco, Negro, Rojo, Verde, Azul, Amarillo, Magenta, Cian. Puede cambiar el color del texto. El valor predeterminado es Blanco.
Color de fondo: Las opciones incluyen Programado, Blanco, Negro, Rojo, Verde, Azul, Amarillo, Magenta, Cian. Puede cambiar el color del fondo de los subtítulos. El valor predeterminado es Negro.
Opacidad de primer plano: Ajusta la opacidad del texto. Las opciones incluyen Programado, Transparente, Traslúcido, Sólido e Intermitente.
Opacidad de fondo: Ajusta la opacidad del fondo de los subtítulos. Las opciones incluyen Programado, Transparente, Traslúcido, Sólido e Intermitente.
Regresar al Predeterminado: Esta opción reajusta las opciones Tamaño, Estilo fuente, Color de primer plano, Color de fondo, Opacidad de primer plano y Opacidad de fondo a sus valores predeterminados.
NOTA
Las Opciones - Subtítulos Dig. sólo están disponibles
x
cuando Servicio1~Servicio6 se pueden seleccionar en el Modo de Subtítulo.
La disponibilidad de los subtítulos depende del programa
x
que se esté emitiendo. Las opciones de color de primer plano y color de fondo no
x
se pueden ajustar con el mismo color. No puede establecer la Opacidad de primer plano y la
x
Opacidad de fondo como Transparente.
General
Modo Juego (Apagado / Encendido): Cuando se conecta una
videoconsola como PlayStation™ o Xbox™, se puede experimentar una sensación más realista al seleccionar el menú de juegos.
NOTA
Precauciones y limitaciones del modo de juego
x
– Si desea desconectarse de la consola de videojuegos y
conectarse a otro dispositivo externo, ajuste la opción Modo Juego como Apagado en el menú de configuración.
– Si visualiza el menú de TV en el Modo Juego, la pantalla tiembla
ligeramente.
Modo Juego no está disponible cuando la fuente de entrada está
x
en el modo TV o PC. Tras conectar la consola de videojuegos, configure Modo Juego
x
como Activado. Desgraciadamente, puede que advierta una reducción en la calidad de la imagen.
Si Modo Juego se configura como Encendido:
x
– El modo Imagen se configura como Normal y el de
Sonido como Cine.
Ecualizador no está disponible.
Transparenc. menú (Claro / Oscuro): Establezca la
transparencia del menú.
Melodía (Apagado / Bajo / Medio / Alto): Establezca que una
melodía se oiga cuando el televisor se encienda o se apague.
Sistema de color AV (Auto, PAL-M, PAL-N, NTSC): Se
puede configurar los estándares de codificación del color para las entradas de señal externas. Normalmente el televisor puede recibir imagen y sonido de buena calidad en el modo Auto. Este modo detecta automáticamente las fuentes de la señal del color. Si la implementación del color no es satisfactoria, elija entre PAL-M, PAL-N o NTSC.
Esta función sólo está disponible en el modo AV.

Imagen sobre imagen (PIP)

PIP
Puede ver simultáneamente el sintonizador de televisión y otra fuente de vídeo externa. PIP(Picture-in-Picture), no se admite en el mismo modo.
MENU Configuración PIP ENTER
NOTA
Para obtener información sobre el sonido de PIP, consulte las
x
instrucciones de Selección de sonido. Si apaga el televisor mientras mira la televisión en el modo PIP, la
x
ventana PIP desaparecerá. Puede notar que la imagen de la ventana PIP llega a ser
x
ligeramente artificial cuando utiliza la pantalla principal para visualizar juegos o karaoke.
Configuración de PIP
x
Imagen principal Imagen secundaria Componente1, 2, HDMI1/DVI,
HDMI2, HDMI3, PC
PIP (Apagado / Encendido): Active o desactive la función PIP.
Aire/Cable (Aire / Cable): Puede seleccionar Aire o Cable
como la fuente de entrada de la subpantalla.
Canal: Seleccione el canal de la pantalla secundaria.
Tamaño (
secundaria.
Posición (
para la imagen secundaria.
Sel. Sonido (Principal / Sub): Puede elegir el sonido que desee (Principal / Sub) en el modo PIP.
/ ): Seleccione un tamaño para la imagen
/  /  / ): Seleccione una posición
TV
03 Funciones básicas
Español
19
Page 58
Funciones básicas
H

Menú de asistencia técnica

MENU Soporte técnico ENTER
Autodiagnóstico
El autodiagnóstico puede tardar unos segundos; es parte del funcionamiento normal del televisor.
Prueba de imagen : Se utiliza para comprobar si hay problemas en
la imagen. : Si no se muestra el patrón de prueba o hay ruido en el patrón
de prueba, seleccione Sí. Puede haber un problema en el televisor. Póngase en contacto con el centro de servicio de Samsung.
No : Si el patrón de prueba se muestra correctamente, seleccione No. Puede haber un problema en el equipo externo. Compruebe las conexiones. Si persiste el problema, consulte el manual del usuario del dispositivo externo.
Prueba de sonido : Utilice el sonido de la melodía incorporada para
comprobar si hay problemas con el sonido.
Si no oye sonido en los altavoces del televisor, antes de realizar la prueba de sonido, asegúrese de que Seleccionar altavoz esté configurado como Altavoz de TV en el menú Sonido.
La melodía se oirá durante la prueba aunque Seleccionar altavoz esté establecido como Altavoz externo o se haya silenciado el sonido con el botón MUTE.
: Si sólo puede oír sonido de un altavoz o no se oye sonido durante la prueba de sonido, seleccione Sí. Puede haber un problema en el televisor. Póngase en contacto con el centro de servicio de Samsung.
No : Si puede oír sonido de los altavoces, seleccione No. Puede haber un problema en el equipo externo. Compruebe las conexiones. Si persiste el problema, consulte el manual del usuario del dispositivo externo.
Solución de problemas: Si parece que hay problemas en el televisor,
consulte este apartado.
Si no se puede aplicar ninguno de los consejos para solucionar los errores, póngase en contacto con el centro de atención al cliente de Samsung.
Actualización del software
Actualización del software se puede efectuar descargando el
último firmware desde “www.samsung.com,” en un dispositivo de memoria USB.
Versión actual es el software ya instalado en el televisor.
El software se representa como “Año/Mes/Fecha_Versión”.
Instalación de la versión más actual
Guía de conexión HD
Consulte esta información cuando conecte dispositivos externos al televisor.
Contacto con Samsung
Consulte esta información si el televisor no funciona adecuadamente o si desea actualizar el software. Puede buscar información relacionada con nuestro centro de llamadas, para descargar los productos y el software.
Actualización del software
Versión actual 2010/01/18_000001
Por USB
Software alternativo
Mover

Enter

Regresar
Por USB: Inserte la unidad USB que contenga el archivo de la actualización del firmware descargado desde “www.samsung. com” en el televisor. No desconecte la alimentación ni extraiga la unidad USB antes de finalizar las actualizaciones. El televisor se apagará y se encenderá automáticamente después de completar la actualización del firmware. Cuando se actualiza el software, la configuración del vídeo y del audio que se haya efectuado vuelve a la configuración predeterminada. Le aconsejamos que anote la configuración para recuperarla fácilmente después de la actualización.
Software alternativo (No disponible.)
Unidad USB
Panel lateral del TV
USB
20
Español
Page 59

Funciones avanzadas

H
SUM

Media Play

04 Funciones avanzadas
MediaPlay
Vídeos
Camb. dispos.
Ver dispositivos
MEDIA.P
Disfrute de archivos de fotos, música y películas almacenados en un dispositivo de clase de almacenamiento masivo (MSC) USB.
MENU Aplicaciones Media Play
(USB) ENTER
 Conexión de un dispositivo USB
1. Encienda el televisor.
2. Conecte un dispositivo USB que contenga archivos de fotos, música o películas al
terminal USB del lateral del televisor.
3. Cuando el USB está conectado al televisor, aparece una ventana emergente. A continuación puede seleccionar Media Play.
Puede que no funcione correctamente con archivos multimedia sin licencia.
Lista de lo que debe saber antes de utilizar Media Play (USB)
MTP (Media Transfer Protocol) no se admite.
x
El sistema de archivos admite FAT16, FAT32 y NTFS.
x
Ciertos tipos de cámara digital USB y dispositivos de audio quizás no sean compatibles con este televisor.
x
Media Play sólo admite dispositivos USB de clase de almacenamiento masivo (MSC). MSC es un dispositivo de clase de almacenamiento
x
masivo sólo de transporte de gran capacidad. Ejemplos de MSC son las unidades de almacenamiento en miniatura, los lectores de tarjetas Flash y las unidades de disco duro de USB (no se admiten concentradores de USB). Los dispositivos se deben conectar directamente al puerto USB del televisor.
Antes de conectar el dispositivo al televisor, haga una copia de seguridad de sus archivos para evitar daños o pérdidas de datos. SAMSUNG no
x
se hace responsable por cualquier daño en los archivos o pérdida de datos. Conecte un disco duro USB al puerto reservado, el puerto USB.
x
No desconecte el dispositivo USB mientras se esté cargando.
x
Cuanto mayor sea la resolución de la imagen, más tiempo tardará en visualizarse en la pantalla.
x
La resolución JPEG máxima admitida es 15360 x 8640 píxeles.
x
Con archivos dañados o que no se admiten, se muestra el mensaje “Formato de archivo no admitido”.
x
Si los archivos están ordenados por la vista básica, se pueden mostrar hasta 1000 archivos en cada carpeta.
x
Los archivos MP3 con DRM descargados desde un sitio de pago no se pueden reproducir. La tecnología Gestión de derechos digitales (DRM)
x
admite la creación, la distribución y la gestión de contenidos de modo integrado y general, incluida la protección de los derechos e intereses de los proveedores de los contenidos, la prevención de copias ilegales de los contenidos, así como la gestión de cobros y acuerdos.
Si hay más de 2 dispositivos PTP conectados, sólo se puede utilizar uno al mismo tiempo.
x
Si se ha conectado más dos dispositivos MSC, alguno de ellos puede que no se reconozca. Un dispositivo que exija mucha energía (más de
x
500mA o 5 V), quizás no se admita. Si se muestra un mensaje de advertencia de sobrealimentación al conectar o usar un dispositivo USB, es posible que el dispositivo no se
x
reconozca o que funcione incorrectamente.
Unidad USB
Panel lateral del TV

Entrar

Regresar
USB
Español
21
Page 60
Funciones avanzadas
Si el televisor no recibe señal de entrada durante el tiempo establecido en Tpo. protección auto., se iniciará el salvapantallas.
x
El modo de ahorro de energía de algunas unidades de disco duro externas se puede desactivar automáticamente cuando éstas se conectan al
x
televisor. Si se utiliza un cable de extensión USB, es posible que el dispositivo USB no se reconozca o que los archivos del dispositivo no se puedan leer.
x
Si no se reconoce un dispositivo USB conectado al televisor, la lista de archivos del dispositivo está dañada o un archivo de la lista no se
x
reproduce, conecte el dispositivo USB al ordenador, formatee el dispositivo y compruebe la conexión. Si un archivo borrado del PC aún se encuentra cuando se ejecuta el reproductor multimedia, utilice la función "Vaciar la papelera de reciclaje"
x
del PC para borrar permanentemente el archivo.
 Pantalla de visualización
Vaya al archivo que desee mediante los botones arriba/abajo/derecha/izquierda y, a continuación, pulse el botón ENTER o  (Reproducir). El archivo se reproduce.
Admite Ver dispositivos y Inicio en la pagina de inicio de Media Play.
Puede confirmar el nombre del
archivo seleccionado y el número
Sección de la lista de clasificación:
Muestra la norma de clasificación.
La norma de clasificación
es diferente según los contenidos.
Información:
de archivos y páginas.
Vídeos
/Movie 01.avi 1/1
Movie 01.avi
Movie 03.avi
Movie 05.avi
Movie 07.avi
Movie 09.avi
SUM
Camb. dispos.
Funcionamiento de los botones
Rojo (Camb. dispos.): Selecciona un dispositivo conectado. Verde (Preferencias): Establece la preferencia del archivo (no se admite en la vista básica) Amarillo (Seleccionar): Selecciona varios archivos de la lista de archivos. Los archivos seleccionados se
marcan con un símbolo.
Azul (Organiz.): Selecciona la lista de clasificación.
Herramientas: Muestra el menú de opciones.
Gracias a los botones  (REW) o (FF), la lista de archivos se puede mover a la página siguiente
o anterior.
Ene.10.2010
Ene.10.2010
Ene.10.2010
Ene.10.2010
Ene.10.2010
Movie 02.avi
Movie 04.avi
Movie 06.avi
Movie 08.avi
Movie 10.avi
Seleccionar Organiz.
Ene.10.2010
Ene.10.2010
Ene.10.2010
Ene.10.2010
Ene.10.2010

Herramientas
Página
Sección de la lista de archivos: Puede confirmar los archivos y grupos que se han ordenado por categoría.
22
Español
Page 61
Vídeos
Movie 01.avi
00:04:03 / 00:07:38 1/1
SUM
Reproducción de vídeo
1. Pulse los botones o para seleccionar Vídeos y, a continuación, pulse el botón ENTER
2. Pulse los botones /// para seleccionar el vídeo que desee en la lista de archivos.
3. Pulse los botones ENTER
– El archivo seleccionado se visualiza en la parte superior con su tiempo de reproducción. – Si se desconoce la información de la hora del vídeo, no se muestran ni el tiempo de reproducción ni la barra de progreso. – Durante la reproducción de vídeos, se puede realizar búsquedas con los botones y .
En este modo, se pueden ver clips de películas contenidos en un juego, pero no se puede reproducir éste.
y Formatos de subtítulo admitidos
Nombre Extensión del
Texto basado en tiempo
MPEG-4
SAMI .smi HTML
SubRip .srt basado en cadenas SubViewer .sub basado en cadenas Micro DVD .sub o .txt basado en cadenas
y Formatos de vídeo admitidos
Extensión del
archivo
*.avi
*.mkv
*.asf ASF
*.wmv ASF Window Media Video v9 1920 x 1080 6 ~ 30 25 WMA
*.mp4 MP4
*.3gp 3GPP
*.vro
*.mpg
*.mpeg
*.ts
*.tp
*.trp
o  (reproducir).
archivo
.ttxt XML
Contenedor Códec de vídeo Resolución
Divx 3.11 / 4.x / 5.1 / 6.0 1920 x 1080 6 ~ 30 8
AVI
MKV
VRO VOB
PS
TS
XviD 1920 x 1080 6 ~ 30 8
H.264 BP / MP / HP 1920 x 1080 6 ~ 30 25
MPEG4 SP / ASP 1920 x 1080 6 ~ 30 8
Divx 3.11 / 4.x / 5.1 / 6.0 1920 x 1080 6 ~ 30 8
XviD 1920 x 1080 6 ~ 30 8
H.264 BP / MP / HP 1920 x 1080 6 ~ 30 25
MPEG4 SP / ASP 1920 x 1080 6 ~ 30 8
H.264 BP / MP / HP 1920 x 1080 6 ~ 30 25
XVID 1920 x 1080 6 ~ 30 8
H.264 BP / MP / HP 1920 x 1080 6 ~ 30 25
MPEG4 SP / ASP 1920 x 1080 6 ~ 30 8
MPEG1 1920 x 1080 24 / 25 / 30 30 MPEG2 1920 x 1080 24 / 25 / 30 30 MPEG1 1920 x 1080 24 / 25 / 30 30
H.264 1920 x 1080 6 ~ 30 25
MPEG2 1920 x 1080 24 / 25 / 30 30
H.264 1920 x 1080 6 ~ 30 25
VC1 1920 x 1080 6 ~ 30 25
Formato
Velocidad de
transferencia (fps)
en el menú Media Play.
Pausa
Velocidad
en bits (Mbps)
AC3 / MPEG / LPCM / AACMPEG2 1920 x 1080 24 / 25 / 30 30
AC3 / AAC / MP3 / DD+ /

Saltar

Herramientas

Regresar
Códec de audio
MP3 / AC3 / LPCM /
ADPCM / DTS Core
MP3 / AC3 / LPCM /
ADPCM / WMA
MP3 / ADPCM / AACMPEG4 SP / ASP 1920 x 1080 6 ~ 30 8
ADPCM / AAC / HE-AAC
AC3 / MPEG / LPCM
HE-AAC
04 Funciones avanzadas
Español
23
Page 62
Funciones avanzadas
Movie 01.avi
00:04:03 / 00:07:38 1/1
SUM
3/15
I Love you
Jhon
Music 1
No Singer
Music 2
No Singer
Music 3
No Singer
Music 4
No Singer
Music 5
No Singer
I Love You
Jhon
1st Album Pop 2010
4.2MB
01:10 / 04:02
SUM
Otras restricciones
NOTA
Si hay problemas con el contenido de un códec, éste no será compatible.
x
Si la información de un contenedor es incorrecta y el archivo presenta errores, no se podrá reproducir correctamente el contenedor.
x
El sonido y el vídeo pueden no funcionar si el contenido tiene una velocidad de bits y de transferencia superior a la de marco/segundo
x
relacionada en la tabla anterior. Si hay un error en la tabla de índice, la función de búsqueda (omitir) no se admite.
x
Decodificador de vídeo Decodificador de audio
• Admite hasta H.264, nivel 4.1
• H.264 FMO / ASO/RS, VC1 SP / MP / AP L4 y AVCHD no se admiten.
• GMC no se admite.
• H.263 no se admite.
Continuación de la reproducción de una película (reanudar reproducción)
Si sale de la función de reproducción de la película, ésta se puede reproducir posteriormente desde el punto en que se detuvo.
1. Seleccione el archivo de película que desee seguir reproduciendo
pulsando los botones o en la sección de la lista de archivos.
2. Pulse los botones
(reproducir) / ENTER.
3. Seleccione Contin. (reanudar reproducción) con el botón azul. La
película se reproducirá desde el punto en que se detuvo.
El botón azul está disponible al reanudar la reproducción.
Si la función Recordatorio cont. pelíc. está configurada como Encendido en el menú Config., aparecerá un mensaje emergente cuando se reanude la reproducción de un archivo de película.
• Admite hasta WMA 7, 8, 9, STD
• WMA 9 PRO no admite multicanal superior a 2 canales o audio sin pérdida.
• La frecuencia de muestreo de WMA de 22050 Hz mono no se admite.
Contin.
Reanuda últ. escena
Contin

Pausa

Saltar

Herramientas

Regresar
Música
Reproducción de música
1. Pulse los botones o para seleccionar Música y, a continuación,
pulse el botón ENTER
2. Pulse los botones /// para seleccionar la música que desee en
la lista de archivos.
3. Pulse los botones ENTER
– Durante la reproducción de música, se puede realizar búsquedas con
los botones y .
Los botones reproducción.
Sólo se muestran los archivos con la extensión MP3 y PCM. Los archivos con otras extensiones no se muestran, aunque se hayan guardado en el mismo dispositivo USB.
Si, al reproducir archivos MP3, el sonido no se oye correctamente, ajuste Ecualizador en el menú Sonido. (Un archivo MP3 demasiado modulado puede ocasionar problemas de sonido.)
Español
24
en el menú Media Play.
o  (reproducir).
(REW) y (FF) no funcionan durante la
Lis repr
Pausa

Saltar

Herramientas

Regresar
Page 63
Fotos
1/1
/Movie 01.avi
SUM
Movie 01.avi
Ene.10.2010
Ene.10.2010
Ene.10.2010
Ene.10.2010
Ene.10.2010
Ene.10.2010
Ene.10.2010
Ene.10.2010
Ene.10.2010
Ene.10.2010
Movie 03.avi
Movie 05.avi
Movie 07.avi
Movie 09.avi
Movie 02.avi
Movie 04.avi
Movie 06.avi
Movie 08.avi
Movie 10.avi
Image1024.jpg 1024x768 2010/2/1 3/15
SUM
Visualización de una foto (o una presentación)
1. Pulse los botones o para seleccionar Foto y, a continuación, pulse el botón ENTER en el menú Media Play.
2. Pulse los botones /// para seleccionar la foto que desee en la lista
de archivos.
3. Pulse los botones ENTER o (reproducir).
– Mientras se muestra una lista de fotos, pulse los botones (Reproducir)
/ ENTER del mando a distancia para iniciar la presentación.
– En la presentación se usan todos los archivos de la sección de la lista de archivos. – Durante la presentación, los archivos se muestran ordenadamente.
Los archivos de música se pueden reproducir automáticamente durante la presentación si Música de fondo está configurado como Encendido.
El Modo BGM no se puede cambiar mientras no haya finalizado la carga de BGM.
 Reproducción de varios archivos
Normal
Pausa

Anterior/Siguiente

Herramientas

04 Funciones avanzadas
Regresar
Reproducción de archivos de vídeo/música/fotos seleccionados
1. Pulse el botón amarillo en la lista de archivos para seleccionar el archivo que desee.
2. Repita el proceso anterior para seleccionar varios archivos.
NOTA
La marca aparece a la izquierda de los archivos seleccionados.
x
Para cancelar la selección, pulse de nuevo el botón amarillo.
x
Para cancelar la selección de los archivos, pulse el botón TOOLS
x
y seleccione Deseleccionar todos.
3. Pulse el botón TOOLS y seleccione Reprod. conten. selec..
Reproducción de grupos de archivos de vídeo/música/fotos
1. Cuando se muestre una lista de archivos, vaya a cualquier archivo del grupo deseado.
2. Pulse el botón TOOLS y seleccione Repr. grupo actual.
 Reproductor multimedia - Funciones adicionales
Clasificación de la lista de archivos
Pulse el botón azul en la lista de archivos para ordenarlos.
Categorías
Vista básica Título Preferencias
Fecha rec. Fecha lejana Artista Álbum Género Ánimo
Mensual
Muestra toda la carpeta. Puede ver una foto seleccionando la carpeta. Ordena y muestra los títulos de archivos por símbolo/número/orden alfabético/especial. Ordena y muestra los archivos por preferencias. Puede cambiar la preferencia del archivo en
la sección de la lista de archivos con el botón verde. Ordena y muestra los archivos por la fecha más reciente.
Ordena y muestra los archivos por la fecha más antigua. Ordena los archivos de música por artista y en orden alfabético. Ordena los archivos de música por álbum y en orden alfabético. Ordena los archivos de música por género. Ordena los archivos de música por el estado de ánimo. Puede cambiar la información del
tipo de música. Ordena y muestra los archivos de fotos por meses.
Funcionamiento Vídeos Música Fotos
Vídeos
Camb. dispos.
2 archivos sel. Página
Seleccionar Organiz.

Herramientas
Español
25
Page 64
Funciones avanzadas
Menú de opciones de reproducción de vídeos/música/fotos
Pulse el botón TOOLS durante la reproducción de un archivo.
Categorías Título Puede ir a otro archivo directamente. Modo de repetición Puede reproducir archivos de películas y de música repetidamente. Imagen Tamaño
(Modo1 / Modo2 / Original) Configuración de la imagen Puede ajustar la configuración de la imagen. (pág. 13, 14, 15, 16) Configuración del sonido Puede ajustar la configuración del sonido. (pág. 16, 17) Configuración de subtítulos Puede reproducir los vídeos con subtítulos. Esta función sólo se activa si los subtítulos tienen
Detener visionado automático / Inic. vis. aut.
Veloc.vis.aut Puede seleccionar la velocidad de presentación durante la misma. Música de fondo Puede seleccionar una música de fondo para la presentación. Zoom Puede ampliar las imágenes en el modo de pantalla completa. Girar Puede girar las imágenes en el modo de pantalla completa. Información Puede ver información detallada acerca del archivo reproducido.
Puede ajustar el tamaño de la imagen según las preferencias.
el mismo nombre de archivo que el vídeo. Se puede iniciar o detener una presentación.
Configuración
Uso del menú de configuración
Recordatorio cont. pelíc. (reanudar reproducción.) (Encendido / Apagado): Seleccionar para mostrar el mensaje de ayuda
emergente para la reproducción de una película desde el punto en que se dejó de ver anteriormente.
Obtener código de registro DivX® VOD: Muestra el código de registro autorizado para el televisor. Si se conecta al sitio web de DivX y
se registra, se puede descargar el archivo de registro VOD. Si reproduce el registro VOD mediante el reproductor multimedia, el registro se ha terminado.
Para obtener más información sobre DivX® VOD, visite “www.DivX.com”.
Obtener código de desactivación DivX® VOD: Si DivX® VOD no está registrado, aparece el código de desactivación de registro. Si
ejecuta esta función cuando DivX® VOD se ha registrado, el registro actual de DivX® VOD se desactiva.
Información: Seleccione esta opción para ver la información del dispositivo conectado.
Funcionamiento Vídeos Música Fotos
 
 
   
26
Español
Page 65

Anynet+

HDMI IN 3
04 Funciones avanzadas
¿Qué es Anynet+?
Anynet+ es una función que permite controlar con el mando a distancia del televisor Samsung todos los dispositivos de Samsung conectados que sean compatibles con Anynet+. El sistema Anynet+ sólo se puede usar con dispositivos de Samsung que tengan la función Anynet+. Para asegurarse de que el dispositivo de Samsung tenga dicha función, compruebe si lleva el logotipo Anynet+.
Para conectar al sistema Home Theater Samsung
1. Conecte los terminales HDMI IN (1(DVI), 2, 3 o 4) del televisor y el terminal HDMI OUT del dispositivo Anynet+ correspondiente
mediante un cable HDMI.
2. Conecte el terminal HDMI IN del sistema Home Theater y el terminal HDMI OUT del dispositivo Anynet+ correspondiente mediante un cable HDMI.
NOTA.
Conecte el cable óptico entre el terminal DIGITAL AUDIO OUT (OPTICAL) del televisor y la entrada de audio digital del sistema Home Theater.
x
Si se sigue la conexión anterior, el terminal Optical sólo produce la salida de 2 canales de audio. Sólo oirá sonido de los altavoces frontales
x
izquierdo y derecho y el subwoofer del sistema Home Theater. Para escuchar el canal de audio 5.1, conecte el terminal
DIGITAL AUDIO OUT (OPTICAL) del DVD/decodificador de satélite (es decir, dispositivo Anynet 1 o 2) directamente al amplificador o al sistema
Home Theater, no al televisor. Puede conectar sólo un sistema Home Theater.
x
Puede conectar un dispositivo Anynet+ mediante el cable HDMI. Algunos cables HDMI pueden no admitir las funciones Anynet+.
x
Anynet+ funciona cuando el dispositivo de AV que admite Anynet+ se encuentra en estado de espera o de encendido.
x
Anynet+ admite hasta 12 dispositivos de AV en total. Tenga en cuenta que puede conectar hasta 3 dispositivos del mismo tipo.
x
Televisor
(DVI)
Cable óptico
Cable de HDMI
Dispositivo
Anynet+ 1
Cable de HDMI
Home Theater
Dispositivo
Anynet+ 2, 3, 4
Cable de HDMI
Español
27
Page 66
Funciones avanzadas
Menú Anynet+
El menú Anynet+ cambia según el tipo y el estado de los dispositivos Anynet+ conectados al televisor.
Menú Anynet+ Descripción
Ver TV Cambia el modo Anynet+ al modo de emisión de TV.
Lista Disp. Muestra la lista de dispositivos de Anynet+.
MENU (nombre_dispositivo) Muestra los menús del dispositivo conectado. Por ejemplo, si se ha conectado un grabador de DVD,
INFO (nombre_dispositivo) Muestra el menú de reproducción del dispositivo conectado. Por ejemplo, si se ha conectado un
Grabación: (*grabador) Inicia inmediatamente la grabación en el grabador. (Sólo está disponible en los dispositivos que
Detener grabación: (*grabador) Detiene la grabación.
Receptor La reproducción del sonido se efectúa a través del receptor.
Cuando hay conectados varios dispositivos de grabación, éstos se muestran como (*grabador), pero si sólo hay conectado un dispositivo, éste se muestra como (*nombre_dispositivo).
 Configuración de Anynet+
MENU Aplicaciones Anynet+ (HDMI-CEC) ENTER
Configuración Anynet+ (HDMI-CEC) (Apagado / Encendido): Para usar la función Anynet+, Anynet+ (HDMI-CEC) debe estar configurado como
Encendido.
Cuando la función Anynet+ (HDMI-CEC) está desactivada, todas las operaciones relacionadas con Anynet+ se desactivan.
Apagado Automatico (No / Si): Configuración de un dispositivo Anynet+ para que se desactive automáticamente cuando el televisor se apaga.
La fuente activa del televisor se debe configurar para que éste utilice la función Anynet+.
Aunque un dispositivo externo aún esté grabando, se puede apagar.
se muestra el menú del disco del grabador de DVD.
grabador de DVD, se muestra el menú del disco del grabador de DVD.
admiten la función de grabación.)
 Conmutación entre dispositivos Anynet+
1. Se muestran todos los dispositivos Anynet+ conectados al televisor.
Si no encuentra el dispositivo que desea, pulse el botón rojo para actualizar la lista.
2. Seleccione un dispositivo y pulse el botón ENTER. Puede cambiar al dispositivo seleccionado.
Sólo cuando Anynet+ (HDMI-CEC) se configura como Encendido en el menú Aplicaciones, aparece el menú Lista Disp..
El cambio al dispositivo seleccionado puede tardar unos 2 minutos. No se puede cancelar la operación de cambio de dispositivo mientras ésta
x
se está efectuando. Si ha seleccionado el modo de entrada externa pulsando el botón SOURCE, no podrá usar la función Anynet+. Asegúrese de cambiar al
x
dispositivo Anynet+ mediante la Lista Disp..
Español
28
Page 67
 Grabación
La grabadora de Samsung permite efectuar una grabación de un programa de televisión.
1. Seleccione Grabación.
Cuando hay más de dos dispositivos de grabación
Cuando hay varios dispositivos de grabación conectados, éstos se muestran en una lista. Seleccione un dispositivo de grabación en
x
Lista Disp..
Si no se muestra el dispositivo de grabación, seleccione Lista Disp. y pulse el botón rojo para buscar los dispositivos.
2. Pulse el botón EXIT para salir.

Se pueden grabar las transmisiones de la fuente seleccionando Grabación: (nombre_dispositivo).

Si pulsa el botón  (REC) grabará lo que está viendo en ese momento. Si está viendo un vídeo desde otro dispositivo, se graba el vídeo de éste.
Antes de grabar, compruebe si la toma de antena está conectada correctamente al dispositivo de grabación. Para conectar correctamente una antena a un dispositivo de grabación, consulte el manual del usuario del dispositivo de grabación.
 Escucha a través de un receptor
Se puede escuchar sonido a través de un receptor (como Home Theater) en lugar de hacerlo mediante el Altavoz de TV.
1. Seleccione Receptor y configure como Encendido.
2. Pulse el botón EXIT para salir.
Si el receptor sólo admite audio, quizás no se muestre la lista de dispositivos.
El receptor no funcionará si no se ha conectado correctamente el terminal de entrada óptico del receptor con el terminal
DIGITAL AUDIO OUT (OPTICAL) del televisor.
Cuando el receptor (sistema Home Theater) está establecido en Encendido, se puede oír la salida de sonido del terminal óptico del televisor. Cuando se ve la televisión a través de un DTV (aéreo), el televisor envía el sonido de 5.1 canales al receptor. Cuando la fuente es un componente digital, como un DVD, y está conectada al televisor a través de HDMI, sólo se oye el sonido de 2 canales del receptor.
NOTA
Sólo puede controlar los dispositivos Anynet+ mediante el mando a distancia del televisor, no con los botones de éste.
x
El mando a distancia del televisor puede no funcionar en determinadas circunstancias. En ese caso, vuelva a seleccionar el dispositivo Anynet+.
x
Las funciones Anynet+ no funcionan con los productos de otros fabricantes.
x
04 Funciones avanzadas
Español
29
Page 68
Funciones avanzadas
 Solución de problemas de Anynet+
Problema Posible solución
Anynet+ no funciona. • Compruebe si el dispositivo es un dispositivo Anynet+. El sistema Anynet+ sólo admite dispositivos Anynet+.
Deseo iniciar Anynet+. • Compruebe si el dispositivo Anynet+ está debidamente conectado al TV y si la opción Anynet+ (HDMI-CEC) del
Deseo salir de Anynet+. • Seleccione Ver TV en el menú Anynet+.
En la pantalla aparece el mensaje “Conectando al dispositivo Anynet+...”.
El dispositivo Anynet+ no funciona. • No se puede utilizar la función de reproducción si se está ejecutando Plug & Play (configuración inicial).
• Sólo se puede conectar un receptor (sistema Home Theater).
• Compruebe si el cable de alimentación de Anynet+ está debidamente conectado.
• Compruebe las conexiones de los cables de vídeo/audio/HDMI del dispositivo Anynet+.
• Compruebe si Anynet+ (HDMI-CEC) está establecido en Encendido en el menú de configuración de Anynet+.
• Compruebe si el mando a distancia del televisor está en modo TV.
• Compruebe si el mando a distancia es compatible con Anynet+.
• Anynet+ no funciona en algunas situaciones. (Búsqueda de canales, funcionamiento de Media Play (USB) o Plug & Play, (configuración inicial), etc.)
• Cuando se conecta o se desconecta el cable HDMI, se han de buscar de nuevo los dispositivos o volver a apagar y encender el televisor.
• Compruebe si la función Anynet+ del dispositivo Anynet+ está activada.
menú de configuración está establecida en Encendido.
• A continuación pulse el botón TOOLS para visualizar el menú Anynet+ y seleccione el menú que desee.
• Pulse el botón SOURCE del mando a distancia del televisor y seleccione un dispositivo que no sea Anynet+.
• Pulse funciona cuando no hay ningún dispositivo Anynet+ con sintonizador incorporado conectado.)
• El mando a distancia no se puede utilizar cuando se está configurando Anynet+ o cambiando a un modo de visualización.
• Utilice el mando a distancia cuando haya terminado la configuración de Anynet+ o el cambio al modo de visualización.
, PRE-CH y FAV.CH para cambiar el modo TV. (Tenga en cuenta que el botón de canal sólo
El dispositivo conectado no se muestra.
El programa de televisión no se puede grabar.
El sonido del televisor no sale a través del receptor.
• Compruebe si el dispositivo admite las funciones Anynet+.
• Compruebe si el cable HDMI está debidamente conectado.
• Compruebe si Anynet+ (HDMI-CEC) está establecido en Encendido en el menú de configuración de Anynet+.
• Vuelva a efectuar una búsqueda de dispositivos Anynet+.
• Sólo puede conectar un dispositivo Anynet+ mediante el cable HDMI. Algunos cables HDMI pueden no admitir las funciones Anynet+.
• Si la conexión se corta por una interrupción de la corriente o porque se ha desconectado el cable HDMI, deberá repetir la búsqueda del dispositivo.
• Compruebe la conexión de la toma de antena del dispositivo de grabación.
• Conecte el cable óptico entre el televisor y el receptor.
30
Español
Page 69

Información adicional

Configuración del transmisor FM
Esta función no está disponible en todos los países.
 Configuración de la frecuencia
y Se debe establecer una frecuencia del transmisor FM distinta a la frecuencia de la radio FM cercana al TV a fin de conseguir una buena
recepción de la señal sin interferencias de radio.
y Si la frecuencia de un canal de TV es inferior al rango de frecuencias FM, el transmisor FM automáticamente actualizará su rango de
frecuencias permisible.
y Si las frecuencias del canal de TV y del transmisor FM son idénticas se producirán interferencias en la señal. Para prevenir esto, el rango
de frecuencia del transmisor FM se muestra automáticamente.
y Si no hay frecuencias de canal de TV dentro del rango de frecuencias FM (83 MHz a 108 MHz), el rango completo desde 88 MHz hasta
107.9 MHz está disponible para su uso.
 Guía de instalación del transmisor FM
El módulo transmisor FM equipa una antena integrada. La intensidad de la señal de la antena puede variar en función del lugar de instalación de la antena y del rendimiento del receptor. Si la intensidad de la señal es débil, intente instalar la antena según uno de los métodos que se explican a continuación.
Método 1 Método 2
Conecte el transmisor FM (fig. 1), fije la brida (fig. 2) y enganche el cable de la antena en la brida.
Si tras utilizar el “Método 1” la recepción no es la adecuada, le aconsejamos que utilice el “Método 2” para instalar el transmisor.
Desenrolle el cable y ponga la antena donde el receptor consiga mejor recepción.
05 Información adicional
2
1
NOTA
(no disponible en algunos lugares)
La instalación de la antena directamente en la parte posterior del televisor puede
x
dar como resultado una intensidad de señal débil. Deje un poco de espacio entre el televisor y la antena.
Si la antena del transmisor FM entra en contacto directo con la antena del TV pueden
x
producirse interferencias en la señal. Si el menú del transmisor FM no está habilitado, compruebe si éste está correctamente
x
insertado en la ranura 1 FM TRANSMITTER. Para oír el audio transmitido desde el televisor en la frecuencia FM en un receptor FM (radio, sistema Home Theater, etc.), desplace la antena del
x
receptor FM hasta que el audio se oiga con claridad. Si utiliza un receptor FM (radio, sistema Home Theater, etc.), podrá disfrutar de un audio de calidad transmitido desde el televisor en la
x
frecuencia FM si está situado a menos de 10 m del receptor. Deberá utilizar el transmisor FM suministrado. De lo contrario, podría dañar el producto.
x
Evite utilizar el transmisor FM suministrado con otros productos.
x
Español
31
Page 70
Información adicional
Ajuste la frecuencia del receptor FM (radio, sistema Home Theater, etc.) con la frecuencia del transmisor FM del televisor. Si la frecuencia no
x
coincide, no se oirá el sonido. Ajuste el volumen del receptor FM a un nivel adecuado.
x
Cuando se apaga el televisor, el receptor FM (radio, sistema Home Theater, etc.) emite ruido estático.
x
Debido a las interferencias con otros dispositivos electrónicos, punto débil de las comunicaciones inalámbricas, puede haber interrupciones o
x
estática en el sonido.
 Formatos admitidos por el transmisor FM
Nombre ESPEC.
Normal 88 MHz~107.9 MHz
Rango de frecuencia
Distancia de transferencia
Montaje del soporte de protección
Al instalar el televisor en una pared, coloque el soporte de protección como se indica.
Coincidencia con frecuencia TV
(Máximo 5 m~10 m: según la posición de la antema y la calidad del receptor)

Instalación del montaje mural

Mínimo 1 m~5 m
Configuración automática del rango
(88 MHz~107.9 MHz)
Soporte de protección
Instalación del equipo de montaje mural
El kit de montaje mural (se vende por separado) permite instalar el televisor en una pared. Si desea más información sobre la instalación de los componentes para el montaje mural, consulte las instrucciones que se facilitan con
dichos elementos. Si necesita ayuda con la instalación del soporte mural, póngase en contacto con un técnico. Samsung Electronics no se hace responsable de los daños causados al producto o al usuario si éste ha efectuado la instalación del televisor.
Especificaciones del equipo de montaje mural (VESA)
El kit de montaje mural se vende por separado.
Instale el montaje mural en una pared sólida, perpendicular al suelo. Para colocarlo en otros materiales de construcción, póngase en contacto con el distribuidor más cercano. Si se instala en el techo o en una pared inclinada, puede caerse y causar graves lesiones personales.
NOTA
Las dimensiones estándar de los equipos de montaje mural se muestran en la tabla siguiente.
x
Al adquirir el equipo de montaje mural, también se distribuye un manual de instalación detallado y todas las piezas necesarias para el montaje.
x
No use tornillos que no cumplan las especificaciones de tornillos estándar VESA.
x
No use tornillos con una longitud superior a la medida estándar o que no cumplan con las especificaciones de tornillos estándar VESA. Los
x
tornillos que sean demasiado largos pueden causar daños en el interior del televisor. Para montajes murales que no cumplen las especificaciones de tornillos estándar VESA, la longitud de éstos puede variar dependiendo de las
x
especificaciones del montaje mural. No apriete excesivamente los tornillos, ya que podría dañar el producto o provocar la caída de éste con riesgo de causar lesiones personales.
x
Samsung no se hace responsable de este tipo de accidentes. Samsung no se hace responsable de daños o lesiones personales cuando se usa un montaje mural que no cumple las especificaciones VESA o
x
si el cliente no sigue las instrucciones de instalación del producto.
32
Español
Page 71
No monte el televisor con una inclinación de más de 15 grados.
x
Son necesarias dos personas para montar el televisor en la pared.
x
05 Información adicional
Familia de
producto
Televisor PDP
Desenrosque los tornillos del kit antes de instalar el montaje mural en la pared.
pulgadas
42~50 400 x 400
58~63 600 x 400
70~79 800 x 400
80~ 1400 x 800
No instale el equipo de montaje mural mientras el televisor está encendido. Se podría producir una descarga eléctrica con riesgo de causar lesiones personales.
Especificaciones
VESA (A * B)
Tornillo
estándar
M8 4
Cantidad

Seguridad en el espacio de instalación

Mantenga la distancia requerida entre el producto y otros objetos (por ejemplo, paredes) para asegurar la ventilación adecuada. En caso contrario, se podría producir un incendio por un incremento de la temperatura interna del producto.
Cuando utilice un soporte o un montaje mural, use sólo las piezas proporcionadas por Samsung Electronics.
Si utiliza piezas proporcionadas por otros fabricantes, podría tener problemas con el producto o éste se podría caer con el riesgo de causar
x
lesiones personales.
El aspecto puede variar según el producto.
Instalación con un soporte Instalación con un montaje mural
4 pulgadas
4 pulgadas
4 pulgadas
4 pulgadas
4 pulgadas
4 pulgadas
4 pulgadas
Español
33
Page 72
Información adicional

Fijación del televisor a la pared

Precaución: Tirar del televisor, empujarlo o colgarse de él puede provocar su caída. En especial, procure que los niños no se cuelguen del televisor ni lo desestabilicen; éste podría caerse sobre ellos y causarles lesiones graves o incluso la muerte. Siga las precauciones de seguridad del folleto de seguridad incluido con el producto. Para mejorar la estabilidad instale un dispositivo antivuelco, como se explica a continuación.
 Para impedir que el televisor se caiga
1. Apriete firmemente las grapas sobre la pared con los tornillos. Asegúrese de que
los tornillos estén bien afirmados en la pared.
Según el tipo de pared quizás necesite algún material adicional para el anclaje.
Las grapas, los tornillos y la cadena no se suministran con el producto; deberá adquirirlos por separado.
2. Quite los tornillos de la parte central posterior del televisor y con ellos monte las
grapas en el televisor.
Quizás con el televisor no vayan incluidos los tornillos. En tal caso debe adquirirlos por separado con estas especificaciones.
3. Monte una cadena fuerte entre las grapas del televisor y de la pared de manera
que quede bien tensada.
NOTA
Instale el televisor cerca de la pared para evitar que caiga hacia atrás.
x
Las grapas de la pared han de estar a la misma o a menor altura que las
x
grapas del televisor. Cuando desee mover el televisor deberá aflojar la cadena.
x
4. Compruebe que todas las conexiones estén bien aseguradas. Compruébelas
periódicamente para detectar cualquier signo de fatiga o de fallo. Si tiene dudas sobre la seguridad de la instalación, póngase en contacto con un instalador profesional.
Pared
34
Español
Page 73

Solución de problemas

Si cree que el televisor tiene un problema, compruebe primero esta lista de posibles problemas y soluciones. Si ninguno de los consejos funciona, visite “www.samsung.com” y haga clic en Support o llame al centro de atención al cliente de Samsung.
Problemas Soluciones y explicaciones
Imagen deficiente En primer lugar, ejecute la Prueba de imagen para confirmar que el televisor muestra correctamente la imagen
La imagen del televisor no se ve tan bien como en la tienda.
La imagen se ve distorsionada: error de macrobloques, microbloques, puntos, pixelización.
El color es de mala calidad o falta. • Si utiliza una conexión de componentes, compruebe que los cables de los componentes estén conectados
El color o el brillo es de mala calidad. • Ajuste las opciones de Imagen en el menú del TV. (vaya a los modos Imagen / Color / Brillo / Definición)
Hay una línea de puntos en el borde la pantalla.
La imagen se ve sólo en blanco y negro. • Si está utilizando una entrada compuesta AV, conecte el cable de vídeo (amarillo) en el terminal verde de la
Al cambiar de canal, la imagen se congela, se ve distorsionada o aparece con retraso.
Problemas del sonido En primer lugar, ejecute la Prueba de sonido para confirmar que el audio del televisor funciona correctamente.
No hay sonido o se oye demasiado bajo con el volumen al máximo.
La imagen es buena pero no hay sonido. • Configure la opción Seleccionar altavoz como Altavoz de TV en el menú de Sonido (pág. 17).
Los altavoces hacen un ruido inapropiado. • Compruebe las conexiones de los cables. Compruebe que no haya un cable de vídeo conectado a una
de prueba. (Vaya a MENU- Asistencia técnica - Autodiagnóstico - Prueba de imagen) (pág. 20) Si la imagen de la prueba se muestra correctamente, la mala calidad de la imagen puede deberse a la fuente o a la señal.
• Si tiene un decodificador por cable/satélite analógico, cámbielo por un decodificador digital HD. Utilice un cable HDMI o de componentes para conseguir una calidad de imagen de alta definición (HD).
• Suscriptores de cable/satélite: Pruebe con estaciones de alta definición (HD) en la oferta de canales.
• Conexión de antena: Pruebe con emisoras de alta definición (HD) después de ejecutar la programación automática.
Muchos canales de alta definición (HD) mejoran los contenidos SD (Standard Definition).
• Ajuste la resolución de la salida de vídeo del decodificador de cable o satélite en 1080i o 720p.
• La compresión de los contenidos de vídeo puede causar imágenes distorsionadas, especialmente en las escenas de movimiento rápido, como en los deportes y las películas de acción.
• Un nivel de señal débil puede causar imágenes distorsionadas. No es un problema del televisor.
• Los teléfonos móviles que se utilizan cerca del televisor (aproximadamente a 1 metro) pueden causar interferencias en la imagen del televisor digital y analógico.
en los terminales correctos. Las conexiones incorrectas o sueltas pueden originar problemas en el color o que la pantalla se quede en blanco.
(pág. 13)
• Ajuste la opción Ahorro energía en el menú del TV. (vaya a MENU- Imagen - Solución Eco - Ahorro energía) (pág. 14)
• Intente reiniciar la imagen para ver la configuración de imagen predeterminada. (vaya a MENU- Imagen - Reinicio de la imagen) (pág. 16)
• Si el tamaño de la imagen está establecido en Ajuste pantalla, cámbielo a 16:9 (pág. 15).
• Cambie la resolución del decodificador de cable/satélite.
entrada 1 de componentes del televisor.
• Si está conectado al receptor de cable, reinicie éste Vuelva a conectar el cable de alimentación y espere a que el decodificador se reinicie. Puede tardar hasta 20 minutos.
• Establezca la resolución de salida del decodificador de cable en 1080i o 720p.
(Vaya a MENU- Soporte técnico - Autodiagnóstico - Prueba de sonido) (pág. 20) Si el audio es correcto, el problema del sonido puede provenir de la fuente o la señal.
• Compruebe el volumen del dispositivo (decodificador de cable/satélite, DVD, Blu-ray, etc.) conectado al televisor.
• Si utiliza un dispositivo externo, compruebe que los cables de audio estén conectados a los terminales de entrada de audio correctos del televisor.
• Si utiliza un dispositivo externo, compruebe que la opción de salida de audio del dispositivo (por ejemplo, quizás deba cambiar la opción de audio del decodificador de cable a HDMI si tiene conectado HDMI al televisor).
• Si se utiliza un cable DVI a HDMI, se necesita un cable de audio independiente.
• Si el televisor tiene un terminal de auriculares, asegúrese de que éstos no estén conectados.
• Reinicie el dispositivo conectado volviendo a conectar el cable de alimentación del dispositivo.
entrada de audio.
• Para la conexión de la antena o el cable, compruebe la potencia de señal. Un nivel de señal débil puede causar distorsiones en el sonido.
• Ejecute la Prueba de sonido como se ha explicado anteriormente.
05 Información adicional
Español
35
Page 74
Información adicional
Problemas Soluciones y explicaciones
No hay imagen, no hay vídeo
El televisor no se enciende. • Compruebe que el cable de alimentación CA esté bien conectado en la toma de la pared y en el televisor.
El televisor se apaga automáticamente. • Compruebe si la opción Temporizador está establecida en Apagado en el menú Configuración (pág. 18).
No hay imagen ni vídeo. • Compruebe las conexiones de los cables (desconecte y vuelva a conectar todos los cables del televisor y
Conexión RF (Cable/Antena)
El televisor no recibe todos los canales. • Compruebe que el cable coaxial esté firmemente conectado.
La imagen se ve distorsionada: error de macrobloques, microbloques, puntos, pixelización.
Conexión de PC
Aparece un mensaje de “Modo no compatible”.
“PC” siempre aparece en la lista de fuentes aunque el PC no esté conectado.
La imagen es buena pero no hay sonido. • Si utiliza una conexión HDMI, compruebe la configuración del audio del PC.
Otros
Barras horizontales rodantes de color púrpura/verde y zumbidos en los altavoces del televisor con la conexión del cable de componentes.
El mando a distancia no funciona. • Cambie las pilas del mando a distancia; haga coincidir los polos (+/–).
• Compruebe que la toma de la pared funcione.
• Intente pulsar el botón POWER del televisor para asegurarse de que el problema no está en el mando a distancia. Si el televisor se enciende, consulte “El mando a distancia no funciona” a continuación.
• Si el televisor está conectado a un PC, compruebe la configuración de la alimentación de éste.
• Compruebe que el cable de alimentación CA esté bien conectado en la toma de la pared y en el televisor.
• Cuando se ve la televisión con una conexión de antena o cable, el televisor se apaga tras 10-15 minutos si no hay señal.
de los dispositivos externos).
• Establezca la salida de vídeo de los dispositivos externos (receptor de cable/satélite, DVD, Blu-ray, etc.) de modo que coincida con las conexiones de la entrada de TV. Por ejemplo, si la salida de un dispositivo externo es HDMI, se debe conectar a una entrada HDMI en el televisor.
• Compruebe que los dispositivos externos estén encendidos.
• Asegúrese de seleccionar la fuente correcta del TV pulsando el botón SOURCE del mando a distancia.
• Reinicie el dispositivo conectado volviendo a conectar el cable de alimentación del dispositivo.
• Ejecute Prog. Auto para añadir los canales disponibles a la lista de canales. Vaya a MENU- Canal - Prog. Auto (pág. 12).
• Compruebe la posición de la antena.
• La compresión de los contenidos de vídeo puede causar imágenes distorsionadas especialmente en las escenas de movimiento rápido, como en los deportes y las películas de acción.
• Un nivel de señal débil puede causar imágenes distorsionadas. No es un problema del televisor.
• Establezca la resolución de salida del PC de modo que coincida con la resolución admitida por el televisor (pág. 10).
• Esto es normal; “PC” siempre aparece en la lista de fuentes aunque no haya ningún PC conectado.
• Desconecte los terminales de audio izquierdo y derecho del decodificador. Si los zumbidos cesan, esto indica que el decodificador tiene un problema en la conexión a tierra. Sustituya los cables de vídeo de componentes por una conexión HDMI.
• Limpie la ventana de transmisión del sensor del mando a distancia.
• Apunte con el mando a distancia directamente al televisor desde una distancia de 1,5 -2 metros.
36
Español
Page 75
Problemas Soluciones y explicaciones
El televisor de plasma emite un zumbido. • Los televisores de plasma normalmente emiten un zumbido suave. Esto es normal. Lo causan las cargas
Problema de retención de imagen (desgaste). • Esta pantalla está equipada con tecnología de reducción de la "quemadura de pantalla" para reducir la
El mando a distancia del cable/decodificador no enciende ni apaga el televisor ni ajusta el volumen.
Aparece el mensaje “Modo no compatible”. • Compruebe la resolución que admite el televisor y ajuste en consecuencia la resolución de salida del
Subtítulo en el menú del televisor aparece atenuado.
Se advierte un olor a plástico que proviene del televisor.
El televisor está inclinado hacia un lado. • Retire la base del soporte de televisor y vuelva a montarla.
El menú del canal se ve atenuado (no disponible)
La configuración se pierde después de 30 minutos o cada vez que se apaga el televisor.
Pérdida intermitente de audio o vídeo. • Compruebe las conexiones de los cables y vuelva a conectarlos.
Puede ver pequeñas partículas si mira de cerca el borde del marco del televisor.
eléctricas que se utilizan para crear las imágenes en la pantalla.
• Si el zumbido es fuerte, quizás se haya configurado el brillo del televisor demasiado alto. Pruebe a establecer un nivel de brillo menor.
• También se puede originar un zumbido fuerte si la parte posterior del televisor de plasma está demasiado cerca de la pared o de otra superficie dura. También puede probar a cambiar el recorrido de los cables de conexión.
• Una instalación inadecuada del montaje mural puede crear un ruido excesivo.
posibilidad de que se queme. La tecnología Cambio de píxel permite definir el movimiento de la imagen arriba o abajo (línea vertical) y de lado a lado (punto horizontal).
• Programe el mando a distancia del decodificador de cable/satélite para que haga funcionar el televisor. Consulte el manual del decodificador de cable/satélite para conocer el código del TV SAMSUNG.
dispositivo externo. Consulte cómo configurar la resolución en la página 10 de este manual.
• No se puede seleccionar Subtítulo en el menú del televisor cuando está conectado a través de HDMI o Component (pág. 18).
• Se debe activar Subtítulo en el dispositivo externo (pág. 18).
• Este olor es normal y desaparece con el tiempo.
• El menú Canal sólo está disponible cuando está seleccionada la fuente TV.
• Si el televisor está en el modo Demo comercio, la configuración del audio y la imagen se restablecerá cada 30 minutos. Cambie la configuración del modo Demo comercio al modo Uso domiciliario en el procedimiento Plug & Play. Pulse el botón SOURCE para seleccionar el modo TV; vaya a MENU Configuración Plug & Play ENTER
• La pérdida de audio o vídeo se puede deber a que los cables son demasiado rígidos o gruesos. Debe asegurarse de que los cables sean lo suficientemente flexibles para un largo periodo de uso. En un montaje mural del televisor, es aconsejable utilizar cables con conectores de 90 grados.
• Esto es una particularidad del diseño del producto y no es un defecto.
(pág. 7).
05 Información adicional
El menú PIP no está disponible. • La función PIP sólo está disponible cuando se utiliza una fuente HDMI, PC o de componentes.
Aparece en la pantalla POP (anuncio de rótulo interno del televisor).
Algunas de las imágenes y funciones mostradas sólo están disponibles en unos modelos determinados.
• Seleccione el modo Uso domiciliario en el modo Plug & Play. Para obtener información, consulte la función Plug & Play (pág. 7).
Español
37
Page 76
Información adicional
Especificaciones
Consideraciones medioambientales Temperatura de funcionamiento Humedad de funcionamiento Temperatura de almacenamiento Humedad de almacenamiento
Soporte giratorio (izquierda / derecha) Nombre del modelo Tamaño de pantalla Sonido
(Salida) Dimensiones (An x Pr x Al)
Cuerpo principal Con el soporte
Peso Sin el soporte Con el soporte
Panel nativo
El diseño y las especificaciones pueden cambiar sin previo aviso.
Para obtener más información sobre la fuente de alimentación y el consumo de energía, consulte la etiqueta adherida al producto.
PL42C450 PL50C450
42 pulgadas 50 pulgadas
10 W x 2 10 W x 2
1031 x 70.9 x 631.0 mm
1031 x 284.5 x 695.5 mm
17.5 kg
19.5 kg
1024 x 768 a 60Hz 1360 x 768 a 60Hz

Licencia

10°C a 40°C (50°F a 104°F)
10% al 80%, sin condensación
-20°C a 45°C (-4°F a 113°F)
5% al 95%, sin condensación
-20˚ ~ 20˚
1202.5 x 69.5 x 720.5 mm
1202.5 x 284.5 x 788 mm
23.4 kg
25.4 kg
Fabricado bajo licencia de Dolby Laboratories. Dolby y el símbolo de la doble D son marcas comerciales de Dolby Laboratories.
Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks. & DTS
2.0+ Digital Out and the DTS logos are trademarks of DTS, Inc. Product Includes software. © DTS, Inc. All Rights Reserved.
DivX Certified to play DivX video up to HD 1080p, including premium content.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX,Inc. This is an official DivX Certified device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play DivX Video-on-Demand (VOD) content. To generate the registration code, locate the DivX VOD section in the device setup menu.
Go to vod.divx.com with this code to complete the registration process and learn more about DivX VOD. Pat. 7,295,673; 7,460,688; 7,519,274
Aviso de la licencia del código abierto
En el caso de que se utilice un software de código abierto, la licencia sobre éste está disponible en el menú del producto. El aviso de la licencia del código abierto sólo está disponible en inglés.
38
Español
Page 77

Índice

05 Información adicional
A
Actualización del software 20 Ahorro energía 14 Ajuste automático 16 Altavoz de TV 17 Altavoz externo 17 Amplificar 16 Anynet+ 27
AUDIO OUT 9
Autodiagnóstico 20
B
Balance de blanco 14 Balance I/D 16 Bloquear 12 Botón FAV.CH 6, 12 Brillo 13
C
Canal favorito 12 Componente 8 Conexión a un dispositivo de audio 9 Conexión a un PC 9 Contraste Dinám. 14
D
Definición 13
DIGITAL AUDIO OUT 9, 27
Dinámico 13 DivX® VOD 26 D-sub 9
E
Ecualizador 16 Edición de canales 12 Editar Nombre 10 Espacio de instalación 33 Especificaciones 38
F
Formatos de vídeo 23 Fotos 25 Frecuencia 10
G
Girar 26 Grabación 29
H
HDMI 8, 27 Herramientas 3 Home Theater 9, 27
I
Idioma 18 Imagen Tamaño 14, 26 Indicador de encendido 5
L
Licencia 38 Lista de Entradas 10
M
Mando a distancia 6 Melodía 19 Menú de canales 11 Modo de espera 5 Modo de repetición 26 Modo película 15 Modo Sólo RGB 14 Mono 17 Montaje mural 32 Música 24 Música de fondo 26
N
Navegar 11
R
Receptor 29 Reloj 18 Reproductor multimedia 21 Resolución óptima 10
S
Secuencia 25 Seleccionar altavoz 17 Seleccionar todo 13 Sensor Eco 14 Símbolo 3 Sintonización fina 13 Solución de problemas 35 Soporte de protección 32
T
Temporizador 18 Temporizador 18 Tibio 14 Título 26 Tono Color 14 Tono del negro 14 Tono Piel 14 Transmisor FM 31 Transparenc. menú 19
U
Unidad USB 20, 21
V
Vídeos 23 Virtual Surround 16 Vista básica 26 Vol.Auto 17 Volumen 5
P
Pilas 6 PIP (imagen en imagen) 19 Plug & Play 7
Español
39
Page 78
This page is intentionally
left blank.
Loading...