Samsung PN42C430A1DXZC, PC430, PN42C430A1D, P4+ 430, BN68-02608A-02 User Manual

Quick Setup Guide

Congratulations on the purchase of your new Samsung TV.

Read this setup guide to get your TV up and running quickly.

	STOP	1-800-SAMSUNG (1-800-726-7864)
		Samsung Electronics America, Inc.
	Please do not return this unit.	85 Challenger Road Ridgefield Park, NJ 07660-2112
		Samsung Electronics Canada Inc.
	If you have problems operating your	55 Standish Court Mississauga, Ontario L5R 4B2
	TV, call:	Call Center hours of operation: Mon-Sun, 9:00 AM -12
	1-800-SAMSUNG (1-800-726-7864)	AM EST.
		To register this product, visit: www.samsung.com/
	For web support please visit:
		register.
	www.samsung.com/support

Step 1: Install the Stand

Follow the steps below to connect the TV to the stand.

NOTE

xx Make sure to distinguish between the front and back of the Stand and Guide Stand when assembling them.

xx Make sure that at least two persons lift and move the PDP TV.

xx Stand the product up and fasten the screws. If you fasten the screws with

the PDP TV placed down, it may lean to one side.
1 With your TV upright, connect the	2 Fasten the two screws (M4 X L16)
TV to the Stand as shown.	at position 1, and then fasten the
	two screws (M4 X L16) at position
	2.
s
s
s
s
	s
Front	s	s
		s

Rear	2

1

Step 4: Connect External Devices

Connecting an AV device (DVD/ Blu-ray player, cable/satellite box, etc.)

Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality.

Audio Cable

(Not Supplied)

HDMI to DVI Cable (Not Supplied)

Very Good Connection

HD connection (up to 720p/1080i)

Using a HDMI to DVI Cable

Device	DVI OUT
AUDIO OUT

Good Connection

Component connection (up to 720p/1080i)

Using a Component Cable

DVD / Blu-ray player / HD Cable Box / HD Satellite receiver (STB)

Device	COMPONENT OUT AUDIO OUT

		Best Connection
		HD connection (up to 720p/1080i)
		Using an HDMI Cable
HDMI Cable		DVD / Blu-ray player / HD Cable Box / HD STB
(Not Supplied)		(Set-Top-Box) satellite receiver

HDMI OUT	Device

Audio Cable (Not Supplied)

Video Cable (Not Supplied)

Lowest Quality Connection

Audio/Video connection (480i only)

Using an Audio/Video Cable

	DVD, Blu-ray player, cable box, STB
	satellite receiver, VCR
Audio Cable (Not Supplied)	VIDEO OUT	AUDIO OUT	Device

		When connecting to AV IN on the back of your TV, attach the
Component Cable (Not Supplied)
		video cable (yellow) to the green jack next to the AV IN label.
		The jack will not match the color of the video cable (yellow).

Connecting an audio device (Home Theater, etc.)

Connect your TV to your Home Theater or other audio device to enjoy enhanced Sound quality.

Analog Audio connection

Using an Audio Cable

Amplifier / DVD Home Theater

	Audio Cable (Not Supplied)			AUDIO IN

Digital Audio connection

Using an Optical Cable

Digital Audio System

Optical Cable (Not Supplied)

OPTICAL

Connecting a PC

Connect your TV to a PC to use it as a Monitor.

HD connection

Using a HDMI to DVI Cable

Audio Cable (Not Supplied)

AUDIO OUT

HDMI to DVI Cable (Not Supplied)

DVI OUT

Step 2: Install the Batteries into the Remote

To install batteries into your remote control, follow these steps:

1. Lift the cover on the back of the remote upward as shown in the figure to the right.

2.Install two AAA batteries.

Make sure to match the + and -

ends of the batteries to the diagram in the battery compartment.

3.Replace the cover.

Step 3: Connect Power and Antenna or Cable

VHF/UHF Antenna

						Connect Ant In to
						• Wall cable jack
						• VHF/UHF Antenna
				or		• Cable or Satellite box
	Best to use 75 ohm (round) cable.					Ant or Cable Out

Make sure the AC power cord is plugged in securely to the wall outlet and the TV.

Antenna Cable (Not Supplied)

Step 5: Run Plug & Play

When you turn on your TV for the first time, it automatically launches the Plug & Play function. With Plug & Play, you can select the On Screen Display language, set the clock mode, and launch the TV’s channel memorizing process.

It also displays connection instructions similar to those in this guide.

To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow buttons on your remote. To make a selection, press the ENTEREbutton.

To skip a screen, press the MENU button. To turn on your TV, press the POWER button on the remote or on the TV. To run Plug & Play, follow these steps:

1 Using your remote control, select the language for the On Screen Display (OSD), and then press the ENTEREbutton.

2 Select Home Use, and then press the ENTEREbutton. If you select Store Demo, the TV will reset your picture and audio settings every 30 minutes.

3 Select the Antenna Source to memorize. you must select

Antenna Source to same type as your cable system type. After selecting source, select Start; then press the ENTERE button on your remote.

Plug & Play

Select Language of the OSD.

English

Language Español

Français

UMove EEnter

Plug & Play

Select ‘Home Use’ when installing this TV in your home.

Store Demo	Home Use
	LMove EEnter

Plug & Play

Select the Antenna source to memorize.

Air	Start
Cable	Start
Auto	Start
UMove	EEnter mSkip

Most cable systems are Standard(STD) systems, If you are not sure about what kind of cable system you have, contact your cable company.

If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4, according to the directions for your cable or satellite box.

4

5

6

The TV memorizes the available channels. This process can take up to 45 minutes.

After the TV has memorized the channels, choose the Clock Mode. Select Auto if you have a digital channel in your area. Select Manual if you don’t, or if you have a cable or satellite box. When done, press the ENTEREbutton.

If you select Manual, the clock setting screen appears.

Select the daylight savings time setting: Off, On or Auto and then press the ENTERE button.

Plug & Play

Auto Program in Progress.
DTV Air : --	Air : --
DTV Cable : --	Cable : --	Cable : 35

48%

Stop

EEnter mSkip

Plug & Play
Set the Clock Mode.
Clock Mode	Auto
	Manual
UMove	EEnter	mSkip

Plug & Play

Set to daylight saving time. Auto

DST On Auto

UMove EEnter mSkip

7 Select the time zone in which you live, and then press ENTERE.

8 After the time zone screen, The connection method for best HD screen quality is displayed. Press Right arrow button on your remote to view each screen in succession. Press the Blue button to skip this section.

9 The Enjoy your TV. screen appears. Then press the ENTEREbutton.

If You Want to Rerun Plug & Play

1.Press the SOURCE button on your remote, then select TV mode.

2.Press the MENU button on your remote to display the menu.

3.Press the ▲ or ▼ button to select Setup, and then press the ENTERE button.

4.Press ENTEREagain to select Plug & Play.

BN68-02608A-02