Page 1
Operation Instruction and Installation
3.
Main Function
Android OS: Froyo
•
MP AF with LED Flash
•3
•7.0"
A-GPS/BT v3.0/USB v2.0/WiFi
•
Recording
•
Sensors: Accelation, Magnetic, Gyro, Light
•
Additional
•
-
-
-
WSVGA TFT Full Touch(C-Type)
(802.11
480p (
:
Application store/Voice&Motion UI
Email/Push Email(Exchange ActiveSync)/Video Messaging Email
Multi-touch, Multi-task manager
D1,
720*480) /
Full HD Playback
a/b/g/n)
1080
p, DLNA
3-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Page 2
Level
6.
S/W Download
6-1.
Repair
1
6-1-1.
Pre-requisite for S/W Downloading
Downloader Program
•
GT-P1010 Mobile Tablet
•
Data Link Cable
•
JIG BOX(GH99-36900A)
•
RF Test Cable(GH39-00985A)
•
JIG Cable(GH81-09211A)
•
Adapter(GH99-38251A)
•
Binary files
•
Settings
※
(Odin3 v1.61.exe)
Data Link Cable
6-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Page 3
Level1Repair
6-1-2.
S/W Downloader Program
Load the binary download program by executing the
■
Odin3 v1.61.exe
"
"
Run this file.
←
Option Selection
.
1
Check Re-Partition, Auto Reboot and F. Reset Time, then select PIT, PDA
-
and CSC Files.
6-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Page 4
Enter Device into Download Mode
.
2
Enter the device into Download Mode by pressing down on Volume Down button
and Power On button at the same time.
Power On Button
Volume Down Button
Level1Repair
Connect the Device to PC via Data Cable.
.
3
Make sure ID:COM box highlighted yellow that the device is connected to the PC.
6-3
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Page 5
Level1Repair
Start Downloading PDA and CSC files by clicking Start Button. Then wait for
.
4
Pass" to be appear on the screen.
"
Once the device boots up,confirm the downloaded version name and etc.
.
5
*#1234#
Full Reset
:
*2767*3855#
:
6-4
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Page 6
Reference Abbreviate
9.
Reference Abbreviate
Advanced Audio Coding.
AAC:
―
―
―
―
―
―
―
―
―
―
―
―
―
―
―
―
―
―
―
AVC :
BER :
BPSK:
CA :
CDM :
C/I :
DMB :
EN
ES
ETSI:
MPEG:
PN :
PS :
QPSK:
RS :
SI :
TDM :
TS
Advanced Video Coding.
Bit Error Rate
Binary Phase Shift Keying
Conditional Access
Code Division Multiplexing
Carrier to Interference
Digital Multimedia Broadcasting
European Standard
:
Elementary Stream
:
European Telecommunications Standards Institute
Moving Picture Experts Group
Pseudo-random Noise
Pilot Symbol
Quadrature Phase Shift Keying
Reed-Solomon
Service Information
Time Division Multiplexing
Transport Stream
:
9-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Page 7
Safety Precautions
1.
Repair Precaution
1-1.
Repair in Shield Box, during detailed tuning. Take specially care of tuning or test, because
―
specipicty of cellular phone is sensitive for surrounding interference(RF noise).
Be careful to useakind of magnetic object or tool, because performance of parts is damaged by
―
the influence of magnetic force.
Surely useastandard screwdriver when you disassemble this product, otherwise screw will be
―
worn away.
Useathicken twisted wire when you measure level.
―
thicken twisted wire has low resistance, therefore error of measurement is few.
A
Repair after separate Test Pack and Set because for short danger(for example an overcurrent
―
and furious flames of parts etc) when you repair board in condition of connecting Test Pack and
tuning on.
Take specially care of soldering, because Land of PCB is small and weak in heat.
―
Surely tune on/off while using AC power plug, becausearepair of battery charger is dangerous
―
when tuning ON/OFF PBA and Connector after disassembling charger.
Don't use as you pleases after change other material than replacement registered on SEC System.
―
Otherwise engineer in charge isn't charged with problem that you don't keep this rules.
1-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Page 8
Safety Precautions
ESD(Electrostatically Sensitive Devices) Precaution
1-2.
Several semiconductor may be damaged easily by static electricity. Such parts are called by ESD
Electrostatically Sensitive Devices), for example IC,BGA chip etc. Read Precaution below.
(
You can prevent from ESD damage by static electricity.
Remove static electricity remained your body before you touch semiconductor or parts with
―
semiconductor. There are ways that you touch an earthed place or wear static electricity prevention
string on wrist.
Use earthed soldering steel when you connect or disconnect ESD.
―
Use soldering removing tool to break static electricity.,otherwise ESD will be damaged by static
―
electricity.
Don't unpack until you set up ESD on product. Because most of ESD are packed by box and
―
aluminum plate to have conductive power,they are prevented from static electricity.
You must maintain electric contact between ESD and place due to be set up until ESD is
―
connected completely to the proper place oracircuit board.
1-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Loading...