Samsung OfficeServ 7000 User Manual

Download

Page 1

System Administration Guide

Page 2

SYSTEM

ADMINISTRATION

AND

SPECIAL FEATURES GUIDE

for

OfficeServ

™ 100, OfficeServ™ 500

™ 7000 Series

April 2007

Samsung Telecommunications America reserves the right without prior notice to revise information in this guide for any reason. Samsung Telecommunications America also reserves the right without prior notice to make changes in design or components of equipment as engineering and manufacturing may warrant. Samsung Telecommunications America disclaims all liabilities for damages arising from the erroneous interpretation or use of information presented in this guide.

Page 3

TABLE OF CONTENTS

ABOUT THIS BOOK .................................................................................... 1

SPECIAL FEATURES

System Ring Plans .......................................................................................................... 2

Manual Ring Plan Change ............................................................................................ 2

Temporary Ring Plan Override ....................................................................................2

Calling The System Operator ...................................................................................... 3

Operator Recalls .............................................................................................................. 3

Executive Barge-in .......................................................................................................... 3

Walking Class of Service ................................................................................................4

In/Out of Group ................................................................................................................4

Direct Inward System Access (DISA) ........................................................................ 5

DISA Security .................................................................................................................... 6

Forced Account Codes ............................................................................................ 6–7

Authorization Codes ...................................................................................................... 7

Using the Tie Line ...................................................................................................... 7–8

CALLER ID SPECIAL FEATURES

Abandon Call List ............................................................................................................ 9

CID on SMDR ....................................................................................................................9

Number to Name Translation ......................................................................................9

Page 4

SYSTEM ADMINISTRATOR PROGRAMMING

Customer Level Access .............................................................................................. 10

Customer Level Access Using the PROG Key ......................................................10

Change Feature Passcode ..........................................................................................11

Set Date and Time Display ................................................................................ 11–12

Reset Station Passcodes to Default ................................................................ 12–13

Program Station Names........................................................................................13–15

Program Trunk Names ..................................................................................................16

Program Station Group Names ................................................................................17

Program System Speed Dial Numbers .......................................................... 18–20

Program System Speed Dial Names........................................................................20

Program Personal Speed Dial Numbers for Other Stations ....................21–23

Program Personal Speed Dial Names for Other Stations ........................23–24

Create Programmed Station Messages ........................................................ 24–25

Set Alarm/Appointment Reminder with Message .................................... 25–26

Managing Key Assignments ............................................................................ 27–28

Programming Account Codes ..................................................................................29

Station Timers ..........................................................................................................30–31

Adding Names to the Translation Table ........................................................31–32

Holiday ..............................................................................................................................33

Customer Set Relocation......................................................................................34–35

SYSTEM MAINTENANCE ALARMS ......................................36

Page 5

Page 6

ABOUT THIS BOOK

This book contains instructions for special features that every telephone user may not need to know.The owner can decide who the system administrator will be and who will have access to these features. Station users can be trained on only the items that apply to them. This procedure will help control costs and telephone abuse.

Several of the features listed in this book are specific to the system operator or attendant position.You can have more than one operator or set your system up to be used without an operator.

The designated system administrator can access specific programs and modify some functions to better manage the OfficeServ 100, OfficeServ 500, OfficeServ 7000 Series office telephone systems. Instructions are detailed and easy to follow. When assistance is needed, contact your installation and service company.

Page 7

SPECIAL FEATURES

SYSTEM RING PLANS

Your system is designed to have a maximum of six different Ring Plans. Each ring plan can be programmed to allow different lines to ring different ring plans to ring different station and/or station groups. Examples of why different ring plans are required can include normal day operation, night operation, using different operators during different lunch shifts and Saturday or evening hours of operation. While the system is in a ring plan, each station will be limited to its individual Ring Plan class of service dialing restrictions.You can place the system in one of any six of these ring plans at any time. Ring Plans are available on an individual tenant basis and may be set automatically or manually. Automatic Ring Plans have an individual start time and will remain in that mode until the beginning of the next defined ring plan. If no automatic timer is set, you must change ring plans manually.

Any of these ring plans can be switched from one plan to another at any time by manually pressing a ring plan button. There are two ways to override the automatic ring plans; one is a temporary override until the next programmed start time, and the other is a permanent override until manually changed.

MANUAL RING PLAN CHANGE

Press the RTO button plus the ring plan passcode (four digits) and the ring plan (1-

6) you wish to set. The system will override all the automatic time tables and will remain in the set ring plan until manually changed.To manually change or cancel the ring plan time override and return ring plan operation to the system clock: press the RTO plus the ring plan passcode (four digits) and a “0”to cancel the ring plan time override and return to normal operation.

TEMPORARY RING PLAN CHANGE

Press the RP button plus the ring plan passcode (four digits) and the ring plan (1-

6) you wish to set.The system will remain in that ring plan until the next automatic start time for the next ring plan goes into effect.

NOTE: This button may also be assigned an extender of one of the six ring plans. Example: An RP button is given an extender of 3 (RP3) and the operation of this button is a push on/push off type of operation with the system always returning to ring plan 1 when the key is turned off.When the system is operating in ring plan 3, the RP3 button will light steady red, and when off the light will also turn off.

Page 8

CALLING THE SYSTEM OPERATOR

Any station that dials 0 will ring its assigned operator. (If tenant service is used, each tenant may have a different operator or operator group.) Calls to the system or tenant operator are easily identified because the CALL key will have a fast flash- ing red light. Station users will never receive a busy signal when they dial 0 or the operator group number.The calls will continue ringing in queue until answered.

NETWORKING: When 2 or more systems are networked a single station or

operator group may receive all calls to a single operator.(Please consult with your service company if required).

OPERATOR RECALLS

Transferred calls that go unanswered will recall to the station that originated the transfer. Should the station that originated the transfer not answer the recall, the call will be sent to the operator as a transfer recall.

A call left on hold will recall the station that put it on hold. If the hold recall is unanswered at the station that originated the hold,the call is sent to the operator.

Both types of recalls will ring and have a slow flashing amber light on the LINE key or CALL key.

NETWORKING: When 2 or more systems are networked a single station or

operator group may receive all recalls to a single operator. (Please consult with your service company if required).

EXECUTIVE BARGE-IN

If you want to break into another conversation, you must be allowed to barge-in and the other station and trunk must not be secure.

• Dial the desired extension or trunk number and listen for the busy signal.

• Press the BARGE button and begin speaking after the tone.

• Hang up when you are finished.

The system can be set for one of the three following barge-in options:

• No barge-in allowed

• Barge-in with intrusion tone

• Barge-in without intrusion tone (service observing)

Page 9

When the second or third option is selected the barger will take priority over the line. This means unless you (barger) hang up first, the station or line you barged into will still be connected to you when the station you barged into hangs up. When the third option is selected, the station that barges-in can monitor the conversation and no warning tone or display will be sent to the station being monitored.The handset transmitter and keyset microphone are disabled.The party that originated the barge-in may join the conversation by pressing the MUTE button on the keyset.Your service company must program these options for you.

WARNING

Barge-in without tone may violate state or federal laws concerning the right to privacy. Samsung Telecommunications America is in no way responsible for the possible misuse of this feature.

WALKING CLASS OF SERVICE

You can change a restricted station’s class of service to the same class as your station, allowing you to make calls or use features that would otherwise be restricted from that station.

• Lift the handset or press the SPK or the MONITOR key.

• Dial 59 and then your extension number.

• Dial your station passcode and receive internal dial tone.

• Dial an access code and then the telephone number—OR—use the desired feature as usual.

• Hang up.The station will be returned to its restricted status.

NOTE:The default station passcode 1234 cannot be used.

IN/OUT OF GROUP

Any station assigned to a station group can remove itself from that group and then reenter the group at a later time.When out of the group, a station can receive calls to its extension number but not to the group.

The number of groups available to choose from may vary depending on your OfficeServ 100 or OfficeServ 500 or OfficeServ 7000 Series system type:

OfficeServ 500 40 Groups & OfficeServ 7200 (500 through 539) or (5000 through 5039 depending if your

system is setup for 4 digits numbering plan)

OfficeServ 500 L 80 Groups & OfficeServ 7400 (500 through 579) or (5000 though 5079 depending if your

system is setup for 4 digits numbering plan)

Page 10

OfficeServ 100 20 Groups & OfficeServ 7100 (500 through 519) these can be changed to 4 digits if

required.

To create a backup or relief operator position,assign the main operator and one or more backup individuals to the operator group.All but the main operator should be out of the group.When it is necessary to use a backup operator, put the desired backup station in the group and remove the main operator. When incoming call traffic is heavy,you can have another station put itself in the operator group along with the main operator to handle the extra call load. If the station does not have an IN/OUT key:

• Lift the handset and dial the feature access code _________________.

• Dial the group number.

• Dial 0 to be out of the group or dial 1 to be in the group.

• Receive confirmation tone and hang up.

If the station has an IN/OUT key:

• Press the IN/OUT key. It will light red when the station is in the group.

• Press the IN/OUT key again. The light is off when the station is out of the group.

NOTE: A station can be in more than one group.

DIRECT INWARD SYSTEM ACCESS (DISA)

From outside of the office,selected individuals can call into the OfficeServ 100 or OfficeServ 500 or OfficeServ 7000 Series system on special DISA line(s). A security code must be entered to gain access. Once these individuals are in the system, they can make outside calls using the office lines or call stations within the system. Individuals who will use DISA must have their stations assigned for DISA access and must change their station passcodes. The default passcode 1234 cannot be used.

• Call in on the DISA line from any phone with tone dialing.

• You will hear a dial tone. Dial your security code (your extension number plus your station passcode).

• If you are allowed access,you will receive a dial tone.

• Dial any line access code, receive outside dial tone and then dial a telephone number OR dial any extension number to call a station in the sys- tem.

• To make another call,press Q, receive dial tone and dial another number.

• Press # and hang up when finished.

Page 11

NOTE: Outgoing DISA calls are controlled by the dialing class of the station identified by the security code.The DISA line must have disconnect supervision from the central office.Insist that this service is verified by your installation/service company.

DISA SECURITY

A common practice among hackers is to repeatedly dial a known DISA access number (usually with a computer) and try a different passcode each time. The hacker hopes to eventually chance upon the correct passcode and thus gain access to your system. The OfficeServ 100, OfficeServ 500, and OfficeServ 7000 Series security feature counts the number of sequential incorrect passcode attempts. If a certain number is reached, DISA is disabled and the system sends an alarm to designated display stations. The number of passcode attempts and the disable duration are both programmable. In addition, the OfficeServ 100, OfficeServ 500, and OfficeServ 7000 systems will print an SMDR record (a customer-provided printer is required) each time an incorrect passcode is entered.

The DISA alarm will ring for a programmable time before canceling the ringing; however, the DISA alarm display will remain until the alarm is cleared.To clear the DISA alarm, follow the following procedure:

• Lift the handset and dial 58.

• Enter the DISA alarm passcode (see your service company).

• Replace the handset.

WARNING

As it is impossible to prevent unauthorized access to your telephone system by hackers,we suggest that you do not turn the DISA feature on unless you intend to use it. If you do use this feature, it is good practice to frequently change passcodes and periodically review your telephone records for unauthorized use.

FORCED ACCOUNT CODES

VERIFIED

When set for this option the user must enter an account code for all outgoing calls. The account code entered will be verified from a system list.Forced verified codes can contain the digits 0~9.

OfficeServ 500 & 7100 999 entries OfficeServ 100 500 entries OfficeServ 7200 & 7400 999 entries

Page 12

NOT VERIFIED

When set for this option the user must enter an account code for all outgoing calls, but the account code is not verified against the system list. Non verified account codes can contain the digits 0~9, * and #.

USING FORCED ACCOUNT CODES

• Lift the handset and press the ACCT CODE key or dial 47.

• Enter the account code.

• Press the account code button again, press TRSF or hookflash (on an SLT). If a correct code is entered, you will hear a dial tone and you can make an outside call in the usual manner.If an incorrect code is entered, the station returns error tone.

This code will always print on SMDR reports. For information on entering and changing forced account codes, see the system administrator programming section of this book.

AUTHORIZATION CODES

Authorization codes are used to validate a station user and give permission to make a call. These four digit authorization codes can be either forced or optional, but if used, are always verified from a system list of 500 entries on the OfficeServ

500 M or L version, the OfficeServ 7100, OfficeServ 7200 and OfficeServ 7400, 250 entries on the OfficeServ 100 and OfficeServ 7100. Each authorization code

has an associated class of service. When the code is entered, the class of service is changed to that of the authorization code.

USING AUTHORIZATION CODES

After going off-hook, the station user must dial Q followed by a four digit authorization code. If you enter a correct code, you will hear confirmation tone and then receive a dial tone and you can make an outside call in the usual manner.The station then follows the dialing class for that authorization code.If you enter an incorrect code, the station returns error tone.This code may or may not print on SMDR reports depending on SMDR programming.

USING THE TIE LINE

OUTGOING

Your office can be connected to another system with a tie line. Use this line to make calls to stations in the other system. If programming allows, you can access

Page 13

lines in the other system to make outside calls. Tie line calls can be put on hold, transferred and conferenced in the same manner as are other outside calls.

• Lift the handset or press the SPK or MONITOR key.

• Dial the tie line access code or press the tie line key.

• When you receive dial tone from the other system, you can dial extension numbers or access outside lines. You must know the extension numbers and the line access codes for the other system.

• Finish the call by replacing the handset or pressing the ANS/RLS or the MONITOR key if you are using a 7 button phone.

NOTE: Outgoing calls are controlled by the station’s dialing class.

INCOMING

Station users in the other system can access the tie line and make intercom calls to stations in your system.Answer tie line calls ringing at your station as you would any other outside call.They can be put on hold,transferred and conferenced in the same manner as are other outside calls.

IN AND OUT ON TIE LINE

Users accessing the tie line from the other system can get a line in your system and make outgoing calls. These calls can be controlled by assigning a dialing class to the tie line. For further information, see your service company.

[NOT SUPPORTED ON OS 7100]

Page 14

CALLER ID

SPECIAL FEATURES

NOTE: The Caller ID features below require optional software and/or hardware. Please ask your installation and service company for details.

ABANDON CALL LIST

The system has a system-wide abandoned calls list that stores CID information for the last 100 calls on the OfficeServ 7000 Series, OfficeServ 500 M and L version and 50 calls on the OfficeServ 100 that rang but were not answered and were accompanied with valid CID information.Calls with CID information consisting of OUT OF AREA, PAYPHONE or PRIVATE will not be stored in the list.The abandoned calls list is accessed using the system administrator’s passcode. When reviewing this list, you are provided options to CLEAR the entry or DIAL the number.You can use the NND key to toggle between the CID name, CID number and the date and time the call came in.The system must be using LCR to dial numbers from the abandoned calls list.

To view the list of abandoned incoming calls for which CID information has been received:

• Dial 64 and dial the system administrator passcode.

• Scroll through the entries using the VOL keys.

CID ON SMDR

The Station Message Detail Records (SMDR) report can be set to include the CID name and number for incoming calls. This format expands the printout to 113 characters.You must use a wide carriage printer or an 80 column printer set to the condensed print option.

NUMBER TO NAME TRANSLATION

The system provides a translation table of 1000 entries in the OfficeServ 7100, 7200 and OfficeServ 500 M,and 2000 entries in the OfficeServ 500 L and in the OfficeServ 7400, and 500 entries on the OfficeServ 100 for use in areas that do

not provide name and number (sometimes called “deluxe”) Caller ID or when ANI is received.When the CID or ANI number is received, the table is searched.When a match is found, the system will display the corresponding name from the table. This will allow users in areas that do not support “deluxe”Caller ID or have only ANI service to provide names for callers.

Page 15

Page 16

CALLER ID SPECIAL FEATURES

INVESTIGATE

Investigate allows selected stations with a special class of service to investigate any call in progress.If CID information is available for an incoming call, you will know to whom this station user is speaking. For outgoing calls, you can see the number that was dialed. After investigating, you may barge-in on the conversation, disconnect the call or hang up your phone to end the investigation.

•At your keyset, press the INVESTIGATE key.

• Enter your station passcode. (Default passcodes cannot be used.)

• Enter the station number to be investigated.

• You can now press BARGE to barge-in on the conversation.

OR You can press NND to view more information about the call. OR

You can press DROP to disconnect the call.

NOTES:

TEAR HERE

1. If the call is an outgoing call, the NND key will not appear.

2. This feature requires optional software and/or hardware.Please ask your

installation and service company for details.

WARNING

This feature may violate state or federal laws concerning the right to privacy.Samsung Telecommunications America is in no way responsible for the possible misuse of this feature.

NOTE: This information is NOT repeated in this user guide.

SYSTEM ADMINISTRATOR

PROGRAMMING

Page 17

Page 18

SYSTEM ADMINISTRATOR

PROGRAMMING

CUSTOMER LEVEL ACCESS

Before any customer programs can be accessed, you must first open system programming using the passcode you have been assigned. You must use a display keyset.Should it become necessary to change this passcode, see your service company.

• While on-hook, press TRSF and then dial 200. Your display shows [ENABLE CUS. PROG. PASSCODE].

• Dial the four digit passcode. The display shows [ENABLE CUS. PROG. - DISABLE].

• Dial 1 to enable. The display shows [ENABLE CUS. PROG - ENABLE].

• Press TRSF.The keyset returns to its idle condition.

• Press TRSF and then dial the three digit program code you want to access. Follow the instructions for that program.

NOTE:You must begin programming within 30 seconds.Once you are in programming, any delay of more than 30 seconds between key strokes will cause the system to automatically close programming.

CUSTOMER LEVEL ACCESS USING THE PROG KEY

A designated keyset may be programmed with a “PROG”key which allows access to the following areas of system programming.When pressed you must enter your station passcode followed by the MMC number. The default station passcode “1234” can not be used. The only MMCs that may entered from pressing the “PROG” key are as follows:

• MMC 100

• MMC 102 Station Forward for All Stations

• MMC 104 Station Name

• MMC 115 Program Message for all Stations

• MMC 116 Alarm and Message

• MMC 505 System Day and Time

• MMC 705 System Speed Dial

• MMC 706 System Speed Dial Name

• MMC 722 Station Key Programming

Station Lock for All Stations

Page 19

CHANGING FEATURE PASSCODE

You can change individual feature passcodes.This program is used to change the passcodes for several features. These features are the following: RING PLAN SERVICE, DISA ALARM, ALARM CLEAR, and AA RECORD. Note: Each passcode is four digits long. Each digit can be 0 to 9.

PROGRAM KEYS

UP & DOWN - Select the extension number. HOLD - Press to reset the passcode to default settings.

Open customer programming and follow the instructions below.

ACTION DISPLAY

1. Press TRSF and then dial 202 CHANGE PASSCODE Display shows R

2. Use the UP and DOWN keys to scroll CHANGE PASSCODE through the different options and press D the right soft keys.

3. Press HOLD to reset the passcode CHANGE PASSCODE

ING PLAN: 0000

ISA ALARM:5678

RING PLAN: 0

000

4. Press TRSF to store and exit programming OR press SPK to store and advance to the next program

SET DATE AND TIME DISPLAY

Should it ever become necessary to correct the date and time displayed on all of the keysets, do so as soon as you notice that they are incorrect. Automatic Operating Mode will not work correctly and SMDR records will be of no value when the date and time are not correct.

The display format is the following:

W (Day of the week): Enter 0 for Sunday and 6 for Saturday. MM (Month): Enter 01 for January and 12 for December. DD (Day of the month): Enter a number in the range of 01–31. YY (Year): Enter the last two digits of the year. HH (Hours): Use the 24 hour clock and enter a number in the range of 00–24. MM (Minutes): Enter a number in the range of 00–59.

Page 20

Failure to enter the time using the 24 hour clock will cause the date to change at 12:00 P.M. Open customer programming and follow the instructions below.

ACTION DISPLAY

1. Press TRSF and then dial 505 OLD:6010184:0047 Display shows NEW:WMMDDYY:HHMM

2. Enter the new time and date using OLD:6010184:0047 the above format NEW:3020994:1445

3. Verify the time and date and reenter OLD:3020994:1445 them if necessary NEW:WMMDDYY:HHMM

4. Press TRSF to store and exit programming OR press SPK to store and advance to the next program

If you have entered invalid data, you will receive an [ INVALID ENTRY ] message for three seconds.Reenter the correct date and time. If the information you entered is incorrect, repeat the procedure.

RESET STATION PASSCODES TO DEFAULT

Individual keyset users can set or change their own individual passcodes. These passcodes are used to lock and unlock keysets, override toll restriction and access the DISA feature. At times, it may be necessary for the system administrator to reset a station’s passcode to default “1234.”This program cannot be used to display passcodes, only to reset them.

PROGRAM KEYS

UP & DOWN - Select the extension number. HOLD - Press to reset the passcode.

Open customer programming and follow the instructions below.

ACTION DISPLAY

1. Press TRSF and then dial 101 [201 Display shows PASSCODE:,,,,

] PASSCODE

Page 21

2. Dial the station number OR use the [205] PASSCODE UP and DOWN keys to scroll through PASSCODE:,,,, the keyset numbers and press the right soft key to move the cursor right

3. Press HOLD to reset the passcode [205] PASSCODE

PASSCODE : 1234

4. Press the right soft key to return to step 2 OR press TRSF to store and exit programming OR press SPK to store and advance to the next program

DEFAULT DATA: ALL STATION PASSCODES = 1234

PROGRAM STATION NAMES

This program is used to assign a character name or identification for each extension.You may assign a name of 11 characters long.

PROGRAM KEYS

UP & DOWN - Used to scroll and move cursor. KEYPAD - Used to enter characters. HOLD - Press to clear entry.

Open customer programming and follow the instructions below.

ACTION DISPLAY

1. Press TRSF and then dial 104 [2 Display shows

2. Dial station number (e.g., 205) [205] STN NAME OR press UP or DOWN to select the station and press the right soft key to move the cursor

3. Enter the station name using the [205] STN NAME procedure described on the next page SAM SMITH and press the right soft key to return to step 2

01] STN NAME

Page 22

4. Press TRSF to store and exit programming OR press SPK to store and advance to the next program

NOTE: Directory information is always 11 characters.

DEFAULT DATA: NONE

Names are written using the keypad. Each press of a key will select a character. Pressing the dial pad key moves the cursor to the next position.For example,if the directory name is “SAM SMITH,” press the number “7” three times to get the letter “S.” Press the number “2” once to get the letter “A.”Continue selecting characters from the table below to complete your message. Press the “A”key to change the letter from upper case to lower case.

NOTE:When the character you want appears on the same dial pad key as does the previous character,press the UP key to move the cursor to the right.

KEYSETS [NOT SUPPORTED ON THE OFFICESERV 7100]

DCS

COUNT 1 2 3 4 5

DIAL 0 Q Z . ) 0

DIAL 1 space ? , ! 1

DIAL 2 A B C @ 2

DIAL 3 D E F # 3

DIAL 4 G H I $ 4

DIAL 5 J K L % 5

DIAL 6 M N O ^ 6

DIAL 7 P R S & 7

DIAL 8 T U V Q 8

DIAL 9 W X Y ( 9

DIAL , := [ ] ,

The # key can be used for the following special characters: #,space, &,!, :, ?, ., %, $,, /, =,[, ], @, ^,(, ), _, +, {, },|, ;, \,“ and ~.

Page 23

iDCS / ITP / DS 5000 KEYSETS

COUNT 1 2 3 4 5

DIAL 0 < > . ) 0

DIAL 1 space ? , ! 1

DIAL 2 A B C @ 2

DIAL 3 D E F # 3

DIAL 4 G H I $ 4

DIAL 5 J K L % 5

DIAL 6 M N O ^ 6

DIAL 7 P Q R S 7

DIAL 8 T U V , 8

DIAL 9 W X Y Z 9

DIAL , := [ ] ,

1. When the character you want appears on the same dial pad key as the previ-

ous character,press UP to move the cursor one space to the right.

2. Other symbols are available for DIAL #.

Page 24

PROGRAM TRUNK NAMES

This program is used to assign a character name or identification for each C.O.line. You may assign a name of 11 characters long.

PROGRAM KEYS

UP & DOWN - Used to scroll and move cursor. KEYPAD - Used to enter characters. HOLD - Press to clear entry.

Open customer programming and follow the instructions below.

ACTION DISPLAY

1. Press TRSF and then dial 404 [7 Display shows

2. Dial trunk (e.g., 704) OR press UP or [7 DOWN to select trunk and press the right soft key to move the cursor

3. Enter the trunk name using the procedure [704] TRUNK NAME

rogram Station Names and press the SAMSUNG

in P right soft key to return to step 2

4. Press TRSF to store and exit programming OR press SPK to store and advance to the next program

01] TRUNK NAME

04] TRUNK NAME

Page 25

PROGRAM STATION GROUP NAMES

This program is used to assign a character name or identification for each station group.You may assign a name 11 characters long.

PROGRAM KEYS

UP & DOWN - Used to scroll and move cursor. KEYPAD - Used to enter characters. HOLD - Press to clear entry.

Open customer programming and follow the instructions below.

ACTION DISPLAY

1. Press TRSF and then dial 602 [5 Display shows the first group

2. Dial the group number (e.g., 505) OR [505] SGR NAME press the UP or DOWN key to make a selection and press the left or right soft key to move the cursor

3. Enter the name using the method [505] SGR NAME

rogr

in P

4. Press the left or right soft key to return to step 2 OR press TRSF to store and exit programming OR press SPK to store and advance to the next program

am Station Names

01] SGR NAME

SAMSUNG

Page 26

PROGRAM SYSTEM SPEED DIAL NUMBERS

The system list starts with 200 numbers and can be increased in blocks of ten.The system may have either 500 or 950 maximum depending on the setting in MMC

861. See your service company to increase or decrease the system list.

The speed dial codes are 500 a line access code and the telephone number to be dialed.The access code can be any line group,individual line,station group or individual extension.The speed dial number can be up to 24 characters long including ,, #,FLASH and PAUSE.

NOTE: If Least Cost Routing (LCR) is being used, the LCR access code must be entered.

When you are entering a speed dial number, there are some special keys that you will need to use.These are the bottom row of programmable keys on the keysets and are known as keys A, B, C, D, E and F.

PROGRAM KEYS

UP & DOWN - Select the speed dial bin. KEYPAD - Used to enter number. HOLD - Press to clear entry. SPK/RLS - Save data and advance to next program. A - Does not have a function. B - Inserts a FLASH. C - Inserts a PAUSE. D - Changes the dialing type from pulse to tone. E - Hides and displays digits. F - Changes display to speed dial name entry.

–999 or 050–999. Each speed dial number consists of

KEYSETS [NOT SUPPORTED ON OFFICESERV 7100]

DCS

12 BUTTON KEYSET

PROGRAMMABLE KEYS LAYOUT

D E

PROGRAMMABLE KEYS LAYOUT

24 BUTTON KEYSET

B C

E F

Page 27

iDCS KEYSETS

8D KEYSET PROGRAMMABLE

KEYS LAYOUT

Transfer Speaker

DS 5000 SERIES KEYSETS

7S KEYSET PROGRAMMABLE

KEYS LAYOUT

21D KEYSET PROGRAMMABLE

KEYS LAYOUT

28D KEYSET, 18D KEYSET

PROGRAMMABLE KEYS LAYOUT

VOLUME

BDF

Transfer

Speaker

14D KEYSET PROGRAMMABLE

KEYS LAYOUT

Open customer programming and follow the instructions below.

ACTION DISPLAY

1. Press TRSF and then dial 705 SYS SPEED DIAL Display shows the first number 5

00:

2. Dial the speed bin desired (e.g., 505) OR SYS SPEED DIAL press UP or DOWN to choose and 505: press the right soft key to move the cursor

3. Enter the access code (e.g., 9—the system SYS SPEED DIAL will automatically insert a dash) followed by 505:9–121223456789 the phone number (up to 24 digits long) and press the right soft key to return to step 2

Page 28

4. Press the F key to toggle to Program SYS SPEED NAME System Speed Dial Names, step 3 to 505: enter the name

5. Press TRSF to store and exit programming OR press SPK to store and advance to the next program

DEFAULT DATA: NO SPEED NUMBERS ASSIGNED

PROGRAM SYSTEM SPEED DIAL NAMES

This program is used to assign a character name or identification for each system speed dial location.This name enables you to locate the speed dial number when you are using the directory dial feature.You may assign a name 11 characters long.

PROGRAM KEYS

UP & DOWN - Used to scroll through speed dial bins. KEYPAD - Used to enter selections. SOFT KEYS - Move cursor left and right. SPK - Used to store data and advance to next program. HOLD - Used to clear previous entry.

ACTION DISPLAY

1. Press TRSF and then 706 SYS SPEED NAME Display shows the first name 5

2. Dial the system speed number (e.g., 505) SYS SPEED NAME OR press UP or DOWN to select the entry 5 number and press the right soft key to move the cursor

3. Enter the name as shown in Program SYS SPEED NAME Station Names and press the right soft 5 key to return to step 2 OR press the F key to toggle to the speed dial number to return to P Numbers, step 4

4. Press the right soft key to return to step 2 above OR press TRSF to store and exit programming OR press SPK to store and advance to the next program

rogram System Speed Dial

00:

05:

05:SAMSUNG

Page 29

PROGRAM PERSONAL SPEED DIAL NUMBERS FOR OTHER STATIONS

Individual station users can program their own numbers,but in cases where this is not practical, or for single line telephone users, this program allows a system administrator to view or change any station’s speed dial numbers. The station speed dial codes are 00–49 or 000–049. Each station begins with ten numbers (00–09) and can be assigned more in blocks of ten (up to a maximum of fifty numbers).

Each speed dial number consists of a line access code and the telephone number to be dialed.The access code can be any line group, individual line, station group or individual extension. The speed dial number can be up to 24 characters long including ,, #, FLASH and PAUSE.

NOTE: If Least Cost Routing (LCR) is used, the LCR access code must be entered.

When you are entering a speed dial number, there are some special keys that you will need to use.These are the bottom row of programmable keys on the LCD 12B and LCD 24B keysets and are known as keys A, B, C,D, E and F.

PROGRAM KEYS

UP & DOWN - Scrolls through extension numbers and speed dial bins. KEYPAD - Used to enter number. HOLD - Press to clear entry. A - Does not have a function. B - Inserts a FLASH. C - Inserts a PAUSE. D - Changes the dialing type from pulse to tone. E - Hides and displays digits. F - Changes display to speed dial name entry.

KEYSETS [NOT SUPPORTED ON OFFICESERV 7100]

DCS

PROGRAMMABLE KEYS LAYOUT

12 BUTTON KEYSET

PROGRAMMABLE KEYS LAYOUT

D E

24 BUTTON KEYSET

B C D

E F

Page 30

iDCS KEYSETS

8D KEYSET PROGRAMMABLE

KEYS LAYOUT

Transfer Speaker

DS 5000 SERIES KEYSETS

7S KEYSET PROGRAMMABLE

KEYS LAYOUT

21D KEYSET PROGRAMMABLE

KEYS LAYOUT

28D KEYSET, 18D KEYSET

PROGRAMMABLE KEYS LAYOUT

VOLUME

BDF

Transfer

Speaker

14D KEYSET PROGRAMMABLE

KEYS LAYOUT

Open customer programming and follow the instructions below.

ACTION DISPLAY

1. Press TRSF and then dial 105 [201] SPEED DIAL Display shows 00 :

2. Dial the station number (e.g., 205) OR [205] SPEED DIAL press UP or DOWN to select the station 00

and press the right soft key to move the cursor OR press the left soft key to go to step 4

3. If the selected station has no speed dial [205

] SPEED DIAL

bins, this display will be shown and a new SPDBLK NOT EXIST station may be selected

Page 31

4. Dial the location number (e.g., 05) OR [205] SPEED DIAL press UP or DOWN to select the location 05: _ and press the right soft key to move the cursor OR press the left soft key to return to step 2

5. Enter the trunk access code (e.g., 9) [205] SPEED DIAL followed by the number to be dialed 05 : 9-4264100_ (e.g., 4264100) OR press the right soft key to return to step 2 OR press the left soft key to return to step 3 OR press HOLD to clear an entry (if an error is made, use the DOWN key to step back)

6. Press the F key to access P Speed Dial Names OR press TRSF to save and exit programming OR press SPK to save and advance to the next program

DEFAULT DATA: NO SPEED DIAL NUMBERS PROGRAMMED

rogram Station

PROGRAM PERSONAL SPEED DIAL NAMES FOR OTHER STATIONS

Each individual station user can program his/her own names but in cases where it is impractical or for single line telephone users, this program allows a system administrator to view or change any station’s speed dial names. The station speed dial codes are 00–49. Each station begins with ten numbers (00–09) and can be assigned more in blocks of ten up to a maximum of fifty numbers.

PROGRAM KEYS

UP & DOWN - Used to scroll through extension numbers and speed dial bins. KEYPAD - Used to enter selections. SOFT KEYS - Move cursor left and right. SPK - Used to store data and advance to next program. HOLD - Used to clear previous entry. ANS/RLS - Used to select ALL.

ACTION DISPLAY

1. Press TRSF and then dial 106 [2 Display shows 00:

01] SPEED NAME

Page 32

2. Dial the station number (e.g., 205) OR [205] SPEED NAME press UP or DOWN to select the station 00: and press the right soft key to move the cursor

3. If the selected station has no speed dial [205 bins, this display will be shown and a new SPDBLK NOT EXIST station may be selected

4. Dial the speed dial location (e.g., 05) OR [205] SPEED NAME use UP or DOWN to scroll through the 01:_ location numbers and use the right soft key to move the cursor OR press the left soft key to return to step 2 above

5. Enter the name using the procedure in [205] SPEED NAME

rogram Station Names and press the 01:SAM SMITH

right soft key to return to step 2 OR press the left soft key to return to step 3

6. Press the F key to access Program

Personal Speed Dial Numbers for Other Stations OR press TRSF to

store and exit programming OR press SPK to store and advance to the next program

] SPEED DIAL

CREATE PROGRAMMED STATION MESSAGES

The programmed station message feature lets you set a message at your phone to notify users with Display Phones that you may be out of town. This way, when Display Phone users call their display will show “OUT OF TOWN”and they will know why you do not answer.

The OfficeServ 100, OfficeServ 500, and OfficeServ 7000 systems allow 15 messages to be programmed in the system list in MMC 715 and each station can program 5 messages individually.

PROGRAM KEYS

UP & DOWN - Select the message number.

Page 33

KEYPAD - Used to enter characters. HOLD - Press to clear entry.

Open customer programming and follow the instructions below.

ACTION DISPLAY

1. Press TRSF and then dial 715 PGM.MESSAGE (01) Display shows the first message GIVE ME THE CALL

2. Dial in the message number (e.g., 11) PGM.MESSAGE (16) OR press UP or DOWN to scroll through EMPTY MESSAGE the messages and press the right soft key to move the cursor

3. Enter in the message using the PGM.MESSAGE (16) procedure in P and press the right soft key to return to step 2 above

4. Press TRSF to store and exit programming OR press SPK to store and advance to the next program

rogram Station Names IN THE SHOWROOM

SET ALARM/APPOINTMENT REMINDER WITH MESSAGE

Keyset users can set their own alarms but standard telephone users cannot. The system administrator can set alarm/appointment reminders for other stations in the system.

PROGRAM KEYS

UP & DOWN - Scroll through extensions. HOLD - Press to clear data. KEYPAD - Used to enter data.

Open customer programming and follow the instructions below.

ACTION DISPLAY

1. Press TRSF and then dial 116 [201 Display shows HHMM: NOTSET

]ALM REM(1)

Page 34

2. Dial the station number (e.g., 205) OR [205]ALM REM(1) press UP or DOWN to select the station HHMM: NOTSET and press the right soft key to move the OR cursor OR press ANS/RLS to select all [ALL]ALM REM(1) stations HHMM: NOTSET

3. Dial 1

4. Enter the alarm time in 24 hour clock [205]ALM REM (2)

5. Enter the alarm type from the list above [205]ALM REM (2)

6. Enter the messages using the procedure [205]ALM REM (2)

7. Press TRSF to store and exit pro-

–3 to select the alarm (e.g., 2) OR [201]ALM REM(1)

press UP or DOWN to select the alarm HHMM: NOTSET and press the right soft key to move the cursor OR press the left soft key to return to step 2

format (e.g.,1300) and the display will HHMM:1 automatically advance to step 5

OR press UP or DOWN to select the HHMM:1300D alarm type and press the right soft key to move the cursor

rogram Station N

in P right soft key to return to step 2

gramming OR press SPK to store and advance to the next program

and press the TAKE MEDICATION

ames

300NOTSET

AILY

Page 35

MANAGING KEY ASSIGNMENTS

You can view station key assignments and add extenders to some of the programmable keys for easy one touch operation of frequently used features.

An extender is a number that makes an otherwise general key very specific. Adding the digit “4”to a PA GE key defines this key for paging zone four. Adding “225” to a directed pickup key will define this key as pickup for extension 225 only.The key must already be assigned by the installing technician.

Use this program to assign extenders to the following keys:

KEY DESCRIPTION EXTENDER

BOSS..............Boss/Secretary ..............................(1–4)

DP ..................Direct Pickup ................................(Extension number or

station group number)

DS....................Direct Station ................................(Any extension number)

FWRD ............Call Forwarding ............................(0–7)

GPIK ..............Group Pick-Up ..............................(01–20)

IG ....................In/Out of Group ..........................(Any group number you are part of )

MMPG ..........Meet Me Page ..............................(0–9, ,)

PAG E ..............Page ................................................(0–9, ,)

PARK..............Park (orbits) ....................................(0–9)

RP....................Ring Plan ........................................(1–6), HOLD for none

SPD ................Speed Dialing................................(00–49, 500–999)

PMSG ............Programmed Messages ............(01–30) [Only 20 on the OS7100]

DIR..................Directory..........................................PERS (1), SYS (2) or STN (3)

VT....................Voice Mail Transfer ......................Voice Mail Group Number

SG....................Station Group ................................501–519 for the OfficeServ 100 & 7100

501–539 for the OfficeServ 500 M 501–579 for the OfficeServ 500 L 501–539 for the OfficeServ 7200 501–579 for the OfficeServ 7400

Page 36

PROGRAM KEYS

UP & DOWN - Select the extension number. KEYPAD - Used to enter extender codes. HOLD - Used to clear the displayed data.

Open customer programming and follow the instructions below.

ACTION DISPLAY

1. Press TRSF and then dial 107 [2 Display shows the first station 01:CALL1

2. Dial the station number (e.g., 205) OR use [2 UP or DOWN to scroll through the station 01:CALL1 numbers and press the right soft key to move the cursor

3. Enter the key number (e.g., 18) OR use [205] KEY EXTEND UP and DOWN to scroll through the keys 18:DS and use the right soft key to move the cursor OR press the key to be programmed

4. Dial the extender according to the list above and the system will display your selection If there are no more entries, press the left soft key to return to step 2

5. Press TRSF to store and exit programming [205] KEY EXTEND OR press SPK to store and advance to the 18:DS207 next program

01] KEY EXTEND

05] KEY EXTEND

Page 37

PROGRAMMING ACCOUNT CODES

This program is used to add or change account code entries.

PROGRAM KEYS

KEYPAD - Used to enter the account code (allowable digits 0–9). UP & DOWN - Used to select entry number. FLASH & TRSF - Used to view and change only the used entries. SPK/RLS - Used to clear data.

Open customer programming and follow the instructions below.

ACTION DISPLAY

1. Press TRSF and then dial 708 ACCOUNT CODE Display shows (0

2. Dial the account code entry (e.g., 005) ACCOUNT CODE OR press UP or DOWN to select the (0 entry number and press the right soft key to move the cursor

3. Enter the account code via the dial pad, ACCOUNT CODE e.g., 1234 (maximum of 12 digits) and (005)1 press the right soft key to move the cursor back to step 2

01)

05)

23456789012

4. Press TRSF to store and exit programming OR press SPK to store and advance to the next program

Page 38

STATION TIMERS

Each station can have five timers customized for them to accommodate station users with individual work habits.These timers are as follows:

NO ANS FWD No Answer Forward

This is the amount of time a call will ring at a station before it forwards to the Forward No Answer destination.The default is 15 seconds and the range is 000 to 250 seconds. Make sure that this timer is not set to a greater value than the transfer recall timer or transferred calls will not forward.

DTMF DUR. DTMF Duration

This is the duration of DTMF tones sent to an analog voice mail port. The default duration is 100 milliseconds and the range is 0100 to 9900 milliseconds.

F-DGT DELY First Digit Delay

This is the time the system will wait before sending DTMF digits to a voice mail port. The default time is 600 milliseconds and the range is from 100 to 9900 milliseconds.

OFFHK SEL. Off Hook Select

This timer controls the delay between going off hook (lifting the handset) and the off hook select destination being called.The default duration is 10 seconds and the range is from 000 to 250 seconds.

EFWD DELAY External Forward Delay

This is the time that a station will ring before a call forwards to the external call forward destination.The default duration is 10 seconds and the range is 1 second to 250 seconds.

Open customer programming and follow the instructions below.

PROGRAM KEYS

KEYPAD - Used to set timer values. UP & DOWN - Used to select extension number. SPK/RLS - Save data and advance to next program.

ACTION DISPLAY

1. Press TRSF and then dial 502 [2 Display shows 010 SEC

01] NO ANS FWD

Page 39

2. Dial the station number (e.g., 205) OR [205] NO ANS FWD press UP or DOWN key to select the 010 SEC station and press the right soft key OR OR press ANS/RLS to select all stations [ALL] N and press the right soft key 010 SEC

O ANS FWD

3. Press UP or DOWN key to select the [205] D station timer and press the right soft key 0100 MS→

4. Enter the new value via the dial pad, [205] DTMF DUR. e.g., 0300 and the system will return 0100 MS→0300 to step 2

5. Press TRSF to store and exit programming OR press SPK to store and advance to the next program

TMF DUR.

ADDING NAMES TOTHE TRANSLATION TABLE

This program allows the system administrator or technician to associate a CID or ANI number received from the Central Office with a name programmed in this translation table. If there is no match between a received number and a name in this table, [no CID name] or [no ANI name] will be displayed.

The translation table consists of 1000 entries in the OfficeServ 500 M and OfficeServ 7100, and OfficeServ 7200 and OfficeServ 7400 systems or 2000 entries in the OfficeServ 500 L system or 500 entries in the OfficeServ 100 system with each entry comprised of a ten digit telephone number and a 16 digit name. S

ee Program Station Names.

Open customer programming and follow the instructions below.

PROGRAM KEYS

UP & DOWN - Used to scroll through options. KEYPAD - Used to enter selections. SOFT KEYS - Move cursor left and right. SPK - Used to store data and advance to next MMC. HOLD - Used to clear previous entry.

Page 40

ACTION DISPLAY

1. Press TRSF and then dial 728 TRANSLATION:(001 Display shows first entry DIGIT:

2. Dial entry number (e.g., 005 or 0005) TRANSLATION:(005) OR use UP and DOWN to scroll DIGIT:_ through entries and press right soft key to select entry

3. Enter telephone number and press TRANSLATION:(005) right soft key to advance to name entry DIGIT:3054264100 OR enter telephone number and press left soft key to return to step 2 above

4. Enter the name using the method TRANSLATION:(005)

rogram Station Names SAMSUNG TELECOM

in P and press right or left soft key to return to step 2 above

press SPK to save and advance

OR to next MMC save and exit programming

DEFAULT DATA: NONE

OR press TRSF to

)

Page 41

HOLIDAY

This program provides the ability to set as many as 20 different holidays.Each holiday will override the System Operating Mode for that particular date with a programmed ring plan.

PROGRAM KEYS

UP & DOWN - Used to scroll through options. KEYPAD - Used to enter selections. SOFT KEYS - Move cursor left and right. HOLD - Used to clear an entry.

ACTION DISPLAY

1. Press TRSF and then dial 512 R

Display shows FOLLOW1

2. Press the right soft key to move the RING PLAN

cursor to bottom half of display FOLLOW1

3. Enter the desired ring plan (e.g.,0-6) RING PLAN

Display will return to STEP 1 FOLLOW4

4. Press UP or DOWN to change display A

to holiday assignment 01:

5. Press the right soft key to move the ASSIGN HOLIDAY

cursor to bottom half of display 0

6. Enter a desired holiday date ASSIGN HOLIDAY

(e.g., 1225) 0

7. Press TRSF to store and exit ASSIGN HOLIDAY

programming OR press SPK to store 01:1225 and advance to the next program

ING PLAN

SSIGN HOLIDAY

Page 42

CUSTOMER SET RELOCATION

This program is used to swap information associated with two stations.All assignments such as trunk ring,station group, station COS, station speed dial etc. will follow this program. 18 button keysets and 28 button keysets can be exchanged. If incompatible set types are selected the system will provide an ERROR: NO MATCH message. 18 button and 28 button key assignments should be taken in consideration when relocating these type of sets.The table below shows which phones can be switched with each other.

NOTE:In order to use this program it must first be activated by a technician. Please see your installing company to have this done if you wish to use this program.

PROGRAM KEYS

UP & DOWN - Used to scroll through options. KEYPAD - Used to enter selections. SOFT KEYS - Move cursor left and right. SPK - Used to store data and advance to next program. HOLD - Used to clear previous entry. ANS/RLS - Used to select ALL.

ACTION DISPLAY

1. Press TRSF 315 SET RELOCATION Display shows EXT _ EXT

2. Enter first station number (e.g.,202) SET RELOCATION Press RIGHT soft key to move cursor EXT 202 EXT _

3. Enter second station number (e.g.,210) SET RELOCATION Press RIGHT soft key to enter data EXT 202 EXT 2

4. Display will return to STEP 1 SET RELOCATION Go to STEP 2 EXT _ EXT OR press TRSF to store and exit programming.

Page 43

DS5007S

YES

DS5014D

DS5021D

ITP-5112L

ITP-5121D

ITP-5107S

iDCS 28B

iDCS 18B

YES

iDCS 8B

YES

CUSTOMER SET RELOCATION ALLOW TABLE

DCS*, DS

& iDCS 64 AOM

YES

Line

Single

[DCS Keysets and 32 button AOM not supported on the OS 7100].

Line

YES

DCS*, DS

& iDCS 64

AOM

iDCS 8B

iDCS 18B

iDCS 28B

ITP-5107S

ITP-5112L

ITP-5121D

DS5014D

DS5021D

DS5007S

Page 44

SYSTEM MAINTENANCE

ALARMS

The OfficeServ 100, OfficeServ 500, and OfficeServ 7000 systems provide a feature that self-checks for any failures.If a failure does occur in the software or hardware, a fault error will be generated and buffered to an alarm report. During an alarm state every phone with an assigned SYSTEM ALARM button will ring and cause the SYSTEM ALARM button to flash amber. A phone with a display should be used so that the alarm information can be viewed.When an alarm occurs, the user can press the SYSTEM ALARM button to view and scroll through the alarms.This will silence the audible part of the alarm, but the SYSTEM ALARM button will continue to flash until your Service Company views and clears the alarms in the alarm report located in the system software.

Page 45

N O T E S

Page 46

FF EE AA TT UU RR EE SS AA NN DD SS PP EE CC IIFF IICC AA TT II OO NN SS

The OfficeServ telephone systems have preset (default) feature access codes that use the following number plan. These codes can be used if a key is not available for the feature you want to use. Standard telephone users must always dial these codes.

0 Call attendant or system operator 10 + xxx Retrieve parked calls 11 Put calls on and take calls off hold 12 + xxx Retrieve calls on hold at

13 Door lock release 16 + xxx Make speed dial calls 17 Save number and redial it 18 Recall dial tone for new call 19 Last number redial 2xx or 2xxx Extension numbers 3xx or 3xxx Extension numbers 400 Cancel do not disturb 401 Set do not disturb 41 Set message no ring 42 + xxx Cancel message 43 Set/return messages 44 Busy station/line callback 45 Busy station camp-on 46 Set up a conference 47 Enter account code 48 Set programmed station message 49 Send flash to outside line 5xx or 5xxx Station hunt groups 55 + 0 Page internal zone zero 55 + 1 Page internal zone 1 55 + 2 Page internal zone 2 55 + 3 Page internal zone 3 55 + 4 Page internal zone 4 55 + 5 Page external zone 1 55 + 6 Page external zone 2 55 + 7* Page external zone 3 55 + 8* Page external zone 4

*External zone 3 and 4 not available on the OfficeServ 7100.

another station

55 + 9 Page all external zones 55 + All page 56 Meet me answer 57 Alarm sensor clear 58 DISA alarm clear 59 Walking class of service 600 Cancel all call forwarding 601 + xxx Set forward all calls 602 + xxx Set forward busy 603 + xxx Set forward no answer 604 + xxx Set fwd busy/no answer 605 + xxx Set forward on DD 606 + xxx Set forward follow me 65 Directed call pickup 66 Group call pickup 67 Universal answer 7xx or 7xxx Individual line numbers 8xx Trunk groups 9 Trunk group 9 (local)

05/07

www.samsung.com/bcs