Samsung NV20 User Manual [en, de]

Notices

1.11.11.01.01.0

1.0

No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, mechanical photocopying, recording or
otherwise, without the prior written permission of the manufacturer.

The information within this manual is subject to change without notice.

The manufacturer shall not be held liable for technical or editorial errors or omissions
contained in herein; nor for incidental or consequential damages resulting from the

furnishing, performance or use of this material.

Microsoft Windows is a registered trademark of the Microsoft Corporation.

Product names mentioned herein are for identification purposes only, and may be
trademarks and/or registered trademarks of their respective companies.

Macrovision Statement

If your computer has a DVD drive and an analog TV Out port, the following
paragraph applies:

This product incorporates copyright protection technology that is protected by method
claims of certain U.S. patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.

Copyright 2003 All rights are reserved

Notices i

Important Safety Information

Safety Instructions

Your system is designed and tested to meet the latest standards for safety of
information technology equipment. However, to ensure safe use of this product, it is
important that the safety instructions marked on the product and in the documentation
are followed.

Always follow these instructions to help guard against personal injury and
damage to your system.

i

Setting Up your System

• Read and follow all instructions marked on the product and in the

documentation before you operate your system. Retain all safety and operating
instructions for future use.

• Do not use this product near water or a heat source such as a radiator.

• Set up the system on a stable work surface.

• The product should be operated only with the type of power source indicated on

the rating label.

• Ensure that the electrical outlet you are using to power your equipment is easily

accessible in case of fire or short circuit.

• If your computer has a voltage selector switch, make sure that the switch is in

the proper position for your area.

• Openings in the computer case are provided for ventilation. Do not block or

cover these openings. Make sure you provide adequate space, at least 6 inches
(15 cm), around the system for ventilation when you set up your work area.
Never insert objects of any kind into the computer ventilation openings.

• Ensure that the fan vents on the bottom of the casing are clear at all times. Do

not place the computer on a soft surface, doing so will block the bottom vents.

• If you use an extension cord with this system, make sure that the total ampere

rating on the products plugged into the extension cord does not exceed the
extension cord ampere rating.

ii Users Manual

Care During Use

• Do not walk on the power cord or allow anything to rest on it.

• Do not spill anything on the system. The best way to avoid spills is to not eat or

drink near your system.

• Some products have a replaceable CMOS battery on the system board. There is

a danger of explosion if the CMOS battery is replaced incorrectly. Replace the
battery with the same or equivalent type recommended by the manufacturer.
Dispose of batteries according to the manufacturer’s instructions. If the CMOS
battery requires replacement insure that a qualified technician performs the task

• When the computer is turned off, a small amount of electrical current still flows

through the computer. To avoid electrical shock, always unplug all power
cables, remove the battery and modem cables from the wall outlets before
cleaning the system.

• Unplug the system from the wall outlet and refer servicing to qualified

personnel if:

– The power cord or plug is damaged.
– Liquid has been spilled into the system.
– The system does not operate properly when the operating instructions are

followed.
– The system was dropped or the casing is damaged.
– The system performance changes.

Replacement Parts and Accessories

Use only replacement parts and accessories recommended by manufacturer.

To reduce the risk of fire, use only No. 26 AWG or larger telecommunications

line cord.

Do not use this product in areas classified as hazardous. Such areas include

patient care areas of medical and dental facilities, oxygen rich environments,

Writtenby:DarylL. Osden

or industrial areas.

Battery Disposal

Do not put rechargeable batteries or products powered by non-removable

rechargeable batteries in the garbage.

Contact the Samsung Helpline for information on how to dispose of batteries that you
cannot use or recharge any longer.

Follow all local regulations when disposing of old batteries.

Important Safety Information iii

Laser Safety

All systems equipped with CD or DVD drives comply with the appropriate safety
standards, including IEC 825. The laser devices in these components are classified as
“Class 1 Laser Products” under a US Department of Health and Human Services
(DHHS) Radiation Performance Standard. Should the unit ever need servicing, contact
an authorized service location.

Laser Safety Note:

Use of controls or adjustments or performance of procedures other than those

specified in this manual may result in hazardous radiation exposure. To

prevent exposure to laser beams, do not try to open the enclosure of a CD or

DVD drive.

Power Cord Requirements

The power cord set (wall plug, cable and AC adapter plug) you received with your
computer meets the requirements for use in the country where you purchased your
equipment.

Power cord sets for use in other countries must meet the requirements of the country
where you use the computer. For more information on power cord set requirements,
contact your authorized dealer, reseller, or service provider.

General Requirements

The requirements listed below are applicable to all countries:

• The length of the power cord set must be at least 6.00 feet (1.8m) and a

maximum of 9.75 feet (3.0m).

• All power cord sets must be approved by an acceptable accredited agency

responsible for evaluation in the country where the power cord set will be used.

• The power cord set must have a minimum current capacity of 7 A and a

nominal voltage rating of 125 or 250 volts AC, as required by each country’s
power system.

• The appliance coupler must meet the mechanical configuration of an EN 60

320/IEC 320 Standard Sheet C7 connector, for mating with appliance inlet on
the computer.

iv Users Manual

Regulatory Compliance Statements

Wireless Guidance

Low power, Radio LAN type devices (radio frequency (RF) wireless communication
devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook
system. The following section is a general overview of considerations while operating
a wireless device.

Additional limitations, cautions, and concerns for specific countries are listed in the
specific country sections (or country group sections). The wireless devices in your
system are only qualified for use in the countries identified by the Radio Approval
Marks on the system rating label. If the country you will be using the wireless device
in, is not listed, please contact your local Radio Approval agency for requirements.
Wireless devices are closely regulated and use may not be allowed.

The power output of the wireless device or devices that may be embedded in your
notebook is well below the RF exposure limits as known at this time. Because the
wireless devices (which may be embedded into your notebook) emit less energy than
is allowed in radio frequency safety standards and recommendations, manufacturer
believes these devices are safe for use. Regardless of the power levels, care should be
taken to minimize human contact during normal operation.

As a general guideline, a separation of 20 cm (8 inches) between the wireless device
and the body, for use of a wireless device near the body (this does not include
extremities) is typical. This device should be used more than 20 cm (8 inches) from the
body when wireless devices are on and transmitting.

This transmitter must not be collocated or operate in conjunction with any other
antenna or transmitter.

Some circumstances require restrictions on wireless devices. Examples of common
restrictions are listed below:

Radio frequency wireless communication can interfere with equipment on

commercial aircraft. Current aviation regulations require wireless devices to be

turned off while traveling in an airplane. 802.11B (also known as wireless

Ethernet or Wifi) and Bluetooth communication devices are examples of

devices that provide wireless communication.

Regulatory Compliance Statements v

In environments where the risk of interference to other devices or services is

harmful or perceived as harmful, the option to use a wireless device may be

restricted or eliminated. Airports, Hospitals, and Oxygen or flammable gas

laden atmospheres are limited examples where use of wireless devices may

be restricted or eliminated. When in environments where you are uncertain of

the sanction to use wireless devices, ask the applicable authority for

authorization prior to use or turning on the wireless device.

Every country has different restrictions on the use of wireless devices. Since

your system is equipped with a wireless device, when traveling between

countries with your system, check with the local Radio Approval authorities

prior to any move or trip for any restrictions on the use of a wireless device in

the destination country.

If your system came equipped with an internal embedded wireless device, do

not operate the wireless device unless all covers and shields are in place and

the system is fully assembled.

Wireless devices are not user serviceable. Do not modify them in any way.

Modification to a wireless device will void the authorization to use it. Please

contact manufacturer for service.

Only use drivers approved for the country in which the device will be used. See

the manufacturer System Restoration Kit, or contact manufacturer Technical

Support for additional information.

vi Users Manual

European Union

The following information is only applicable to systems labeled with the CE mark .

European Directives

This Information Technology Equipment has been tested and found to comply with the

following European directives:

• EMC Directive 89/336/EEC with amending directives 92/31/EEC & 93/68/

EEC as per

– EN 55022 Class B

– EN 61000-3-2

– EN 61000-3-3

– EN 55024

• Low Voltage Directive (Safety) 73/23/EEC as per EN 60950(A1/A2/A3/A4/

A11)

• Radio and Telecom Terminal Equipment Directive 199/5/EC as per

– CTR21 (if fitted with a modem device)

– ETS 300 328 (if fitted with a 2.4 GHz band embedded wireless device)

– ETS 301 489-1 (if fitted with a 2.4 GHz band embedded wireless device)

– ETS 301 489-17 (if fitted with a 2.4 GHz band embedded wireless device)

European Radio Approval Information (for products fitted with EU-approved radio devices)

This Product is a Notebook computer; low power, Radio LAN type devices (radio
frequency (RF) wireless communication devices), operating in the 2.4 GHz band, may
be present (embedded) in your notebook system which is intended for home or office
use. This section is only applicable if these devices are present. Refer to the system
label to verify the presence of wireless devices.

Wireless devices that may be in your system are only qualified for use in the European
Union or associated areas if a CE mark with a Notified Body Registration Number
and the Alert Symbol is on the system label.

The power output of the wireless device or devices that may be embedded in you
notebook is well below the RF exposure limits as set by the European Commission
through the R&TTE directive.

Regulatory Compliance Statements vii

European States qualified under wireless approvals:

EU

Austria, Belgium, Denmark, Finland, France (with frequency
restrictions),

Germany, Greece, Ireland, Italy, Luxembourg, The

Netherlands, Portugal, Spain, Sweden and the United Kingdom.

Accept EU

Iceland, Liechtenstein, Norway and Switzerland

European States with restrictions on use:

EU

In France, the frequency range is restricted to 2446.5-2483.5 MHz for
devices above 10 mW transmitting power such as wireless LAN.

Accept EU No limitations at this time.

European Telecommunication Information (for products fitted with EU-approved modems)

Marking by the symbol indicates compliance of this equipment to the Radio and
Telecom Terminal Equipment Directive 1999/5/EC. Such marking is indicative that
this equipment meets or exceeds the following technical standards:

CTR 21 – Attachment requirements for pan-European approval for connection to the
analogue Public Switched Telephone Networks (PSTNs) of TE (excluding TE
supporting voice telephony services) in which network addressing, if provided, is by
means of Dual Tone Multi-Frequency (DTMF) signaling.

Although this equipment can use either loop disconnect (pulse) or DTMF

(tone) signaling, only the performance of the DTMF signaling is subject to

regulatory requirements for correct operation. It is therefore strongly

recommended that the equipment is set to use DTMF signaling for access to

public or private emergency services. DTMF signaling also provides faster call

setup.

This equipment has been approved to Council Decision 98/482/EEC—“CTR 21” for
Pan-European single terminal connection to the Public Switched Telephone Network
(PSTN).

However, due to differences between the individual PSTNs provided in different
countries, the approval does not, of itself, give an unconditional assurance of
successful operation on every PSTN termination point. In the event of problems, you
should contact manufacturer Technical Support.

viii Users Manual

Using Your Documentation

Congratulations on your purchase of a notebook computer with the Windows® XP
operating system. Whether you are new to using a portable computer or are an
experienced user, this user’s manual can help you get the most from your computer.

Manual Documentation Conventions

Information Icons

Three icons and their associated messages appear in this manual. The information
icons are placed before the step/information they apply to:

Warning:

Indicates the possibility of personal injury.

Caution:

Warns you of possible damage to equipment or data.

Note:

Informs you of special circumstances.

Technical Information:

Informs you of special requirements or limitations for use of item(s).

Keyboard Conventions

Keys that you need to press to perform certain functions are displayed in the manual
using a small graphic of the button.
For example: <Ctrl> indicates the control key (Ctrl on the keyboard).

If you need to press two keys at the same time, the key names are shown joined by a
plus sign.
For example: <Fn+F9> means that you should press the Fn key and hold it and then
press the F9 key.

Using Your Documentation 1

CD-ROM Device Naming Convention

In many installation programs you will have to get a program from the CD-ROM
device. The program installation sequence assumes that the CD is drive d:\, however
this is not always the case. The name of the CD-ROM drive is the letter following the
letter assigned to your last HDD. For instance, if you have one HDD with two
partitions, the HDD is drives C: and D: and the CD-ROM drive is then drive E.

Touchpad Conventions

You may be asked to click or double-click on items on the display screen. As a general
note the touchpad actions act much in the same way as a wheel mouse, any differences
are explained fully.

The object that needs to be clicked upon will be displayed in Bold text or shown in a
small figure such as the “Start Button” shown on the right =>.

Table 1. Touchpad Click Conventions

Action Process

Click Depress the touchpad left button and release

Double-click Quickly click the left touchpad button two times

Windows Conventions:

Almost all “Windows” programs will display the name/function of a button or

icon if you place the touchpad pointer on the item you want information about.

Software User Documentation

Your computer is shipped from the factory with several software programs installed.
The software may include its own online or printed documentation. Refer to the
documentation or the Help options in the software for more information.

The figures and illustrations in this manual may not be identical to those on

your system.

General Icon Note:

Some of the Icons used in Windows XP may be placed on the taskbar by

selecting (ex: Place the volume icon in the taskbar) in the properties dialog

box.

2 Users Manual

Introducing Your Computer

This section explains the location of all buttons, LEDs and equipment needed to
operate your notebook computer.

Front

LCD Latch

Fan Vent

Microphone

Speaker

Hot Keys

Keyboard

Touchpad Buttons

Touchpad

Scroll Wheel

LEDs

Power Button

LEDs
(Light

Speaker

Introducing Your Computer 3

Emitting
Diode)

Right Side

PCMCIA

Card Slot

Left Side

CD Drive (option)Hard Disk Drive (HDD)

Headphone / S/PDIF Jack

Microphone Jack

Back Side

4 Users Manual

Security Lock Port

PS/2 Port

Modem Port

LAN Port

Serial Port

TV Out Port (S-VHS)

Parallel

Printer Port

USB Ports

IEEE 1394 Port (option)

DC-In Port

Monitor Port

Battery

Fan Vent

Bottom

Fan Vent

HDD Compartment

Keyboard Screw

HDD Screw

Battery Cover
Latch

Introducing Your Computer 5

Using Your Computer for the First Time

Turning the Computer On and Off

To turn on the computer

1. Insert the battery and connect the AC adapter according to the Installation Guide.

2. Slide the LCD latch to the right and open the LCD panel.

3. Press the power button.

LCD Latch

Power Button

To turn off the computer

1. Click the start button ( ) on the taskbar.

2. Click Turn Off Computer.

Power LED

6 Users Manual

3. Click Turn Off.

If the computer is not turned off properly due to a system error, press

<Ctrl>+<Alt>+<Delete>. When [Windows Task Manager] dialogs appears,

click Shut Down > Turn Off to turn off the computer. Your unsaved work may

be damaged.

If <Ctrl>+<Alt>+<Delete> keys do not operate either, press the power button

for more than 4 seconds to turn off the computer. Your unsaved work may be

damaged. When you turn on the computer next time, it will perform a disk

checking process.

Using Your Computer for the First Time 7

Tips for Using Your Computer

The following information helps you avoid potential problems as you use your
computer:

Do not try to disassemble your computer. Opening the system chassis voids

your warranty. Only an authorised manufacturer service center can replace or

add any parts inside the chassis.

• Follow all the instructions and cautions in your computer user documentation.

• The LCD has a polarized surface and can be damaged easily. To prevent

damage, avoid touching the screen.

• Use only approved AC adapters, auto adapters, memory modules and other

options.

• Because a notebook computer is small and has restricted air flow around

components, it is more likely to overheat than a desktop computer. A fan inside
your computer runs when needed to help eliminate heat. Make sure the fan vent
on the bottom of your computer is not blocked when the computer is in use.
Occasionally check the vents and remove any accumulated dust on the outside.

• Avoid using or storing the computer in extremely hot or cold areas, such as a

car on a hot day. Keep the computer away from heaters and out of direct
sunlight. Exposure to excessive heat may damage computer components. If you
have left your computer in a hot place, let it cool down slowly to room
temperature (with the LCD panel open) before using it.

• Do not remove the memory-module compartment door, or try to install a

memory module when the computer is on. (For information on installing
memory modules, see “Installing a Memory Module” on page 68.)

• Set up your computer work area to avoid physical strain. Sit with your back

straight and supported by your chair. Adjust your chair or work table so that
your arms and wrists can remain in a relaxed position, parallel with the floor.
Avoid bending or twisting your wrists as you work. Your hands should “float”
slightly above the keyboard. Refer to a book on office ergonomics for more
information on setting up your work area.

• Take frequent breaks from working at the computer to rest your eyes and

stretch your muscles.

• Remember to save your data files frequently and to make backup copies of your

files.

8 Users Manual

Travelling with Your Computer

Air Travel

If you are travelling by air, follow these tips:

• Take the computer with you as carry-on luggage. Do not check the computer

with your baggage.

• Allow the computer and disks to go through the X-ray security devices. Do not

hand-carry disks through the walk-through metal detectors, which can cause
loss of data.

• Make sure that the battery is charged or the power cord is easily accessible.

You may be required to turn on the computer for airport security personnel.

• Be prepared to turn off the computer during take off and landing.

Locking your Computer

As a precaution when you are travelling or using your computer in an unsecured area,
you should keep your computer as safe as possible. An option to do this is the Security
Lock System. Follow the Security Lock System manufacturers instructions for specific
installation and use. The following figure shows generally how to use the lock.

Using Your Computer for the First Time 9

Handling Spills

Do not spill anything on your computer. The best way to avoid spills is to avoid eating
and drinking around your computer. If you do spill something on your computer, turn
off your computer, unplug it immediately, and do the following:

• If you spill liquid on the keyboard, drain as much of the liquid from the

keyboard as possible. Be careful not to let the liquid drip onto the LCD panel.
Allow the system to dry for several days before trying to use it.

• If you spill liquid on an external keyboard or keypad, unplug it and drain as

much of the liquid as possible. Allow the keyboard to sit at room temperature
for a full day before trying to use it.

Sweet liquids leave a sticky residue that may jam the keyboard despite your

efforts to dry it.

• If you spill liquid on the LCD panel, clean it immediately with a soft cloth and

denatured alcohol or a proprietary LCD screen cleaner. Do not use water,
window cleaner, acetone, aromatic solvent, or dry, rough towels to clean it.

Some liquids damage the polarized LCD screen. If your screen is damaged,

contact your authorized manufacturer’s service center for a replacement.

Storing the Computer for Long Periods

If possible, leave the power cord connected to the computer and an electrical outlet
when the computer is not in use. This extends the life of the battery and keeps the
battery fully charged.

If you will not be using the computer for a long period of time (a month or more), you
should charge the battery until it is completely full. After you have done so, remove the
battery from the unit.

10 Users Manual

Using the Keyboard

Your computer has an 87/88-key keyboard. By pressing designated key combinations,
you can have access to all the key functions of a full-sized keyboard.

Function & Special Purpose Keys

Embedded Numeric Keypad

Cursor/Screen

Control Keys

Function

Key

Windows

Key

Although the layout of the keys on your computer’s keyboard is different from

that on a desktop computer’s keyboard, the keyboard feels like a full-sized

keyboard when you use it.

Application Key

The keys on the keyboard can be grouped into the following categories:

• Full-sized Alphanumeric typewriter keys are arranged like a standard

typewriter keyboard and are used for text entry. The Windows keys on either
side of the spacebar open Windows menus and perform other special functions.

• Function keys, when pressed together with the <Fn> key, enable special

functions.

• Cursor and Screen control keys move the cursor. They may perform other

functions, depending on your software.

Using the Keyboard 11

To clean the computer keyboard, use slightly damp cotton swabs. Scrub the keys and
the surface around the keys.

Do not allow liquid to drip into the keyboard or you may damage the keyboard.

Using the Numeric Keypad

Your keyboard includes a numeric keypad, which is a group of keys that you can set to
type numbers and mathematical symbols, such as the plus sign. A number or symbol
on the left corner of each keypad key shows its numeric function.

Num Lock LED

Press <Fn+F9> to turn on the embedded numeric keypad. The numeric functions of
the keypad are enabled and the Num Lock LED turns on. (See ”Reading the Status
Indicators” on page 18 for the location of the Num Lock LED.)

While the numeric functions are enabled, you can temporarily return a key to its normal
function by pressing the key and the <Fn> key. For example to type the letter m, press
<Fn+M>. This operation displays the letter m.

To turn the numeric keypad off, press <Fn+F9> again. The Num Lock LED turns off.

12 Users Manual

Using Special Function Keys

The function key activates special functions when it is pressed in combination with
another keys. The table below shows the special key combinations.

<Fn> Key
Combinations

<Fn+F3> F3

<Fn+F4> F4

<Fn+F9> F9

<Fn+F10> F10

<Fn+F11> F11

<Fn+F12> F12

<Fn+Home> Home

<Fn+PgUp> PgUp

<Fn+PgDn> PgDn

<Fn+Up Arrow> Up Arrow

<Fn+Down Arrow> Down Arrow

Key Name Key Function

LCD/CRT

Standby

Numlock

Scroll Lock

Pause

Break

Mute

Volume Up

Volume Down

Brightness Up

Brightness Down

Switches the display between the LCD, the external monitor, and
simultaneous display on both the LCD and the external monitor.

Puts the computer into Suspend mode. To resume normal operation
from rest, press the power button. (See ”Using Power Management
Options” on page 61 for more information about the standby mode.)

Activates the numeric keypad

In some applications, sets the cursor-control keys to scroll the page
up or down while the cursor position does not change. Pressing key
combination again turns off the scrolling function.

In some applications, this will pause the program. Pressing key
combination again turns off the pause function.

In some applications, this will stop (Break) the program.

Mutes the audio.

Increases the audio volume.

Decreases the audio volume.

Increases the LCD brightness.

Decreases the LCD brightness.

When you press a function key combination, the system sound may be

temporarily muted.

Using the Keyboard 13

Hot Keys

You may program the three keys to the left of the power button to start any program
you have installed on your computer.

Internet Key

E-Mail Key

User Key

The default settings for these keys are:

Internet Explorer Outlook Express Windows Calculator

To reprogram the hot keys, follow the steps below:

1. Double-click icon on the Windows taskbar, the Key Setting window is

displayed.

2. Select a key and click the Browse to locate the program you wish to assign to the

3. Click on your program choice to select it. Click Open.

4. Click OK to close window.

14 Users Manual

key.

Using the Touchpad

On Windows, you always see a small graphical image on the screen that indicates the
location where you can take the next action. This image is called a pointer, and is
usually displayed in arrow shape ( ) or ‘I’ shape ( ).

Touchpad

Touchpad Buttons

The touchpad on your computer allows you to move the pointer on the LCD screen,
just like a mouse that is used with a desktop computer. The touchpad buttons allow you
to take actions with the pointer, such as selecting an item or executing a command. The
scroll wheel between the touchpad buttons moves the displayed area up and down
within a window.

Scroll Wheel

Using the Touchpad 15

You can use various actions with your touchpad as described below.

d

Action Function Process

Move Move the pointer Place your finger on the touchpad

and slide your finger to a
destination.

Click Select an object, open a menu, or

Double-Click Launch a program or open a file Place the pointer over an object,

Right-Click Display a short cut menu Place the pointer over an object,

execute a button

Place the pointer over an object,
then press left touchpad button
once.

Or, place the pointer over an
object, then tap the touchpad once
with your finger.

then quickly press left touchpad
button twice.

Or, place the pointer over an
object, then quickly tap the
touchpad twice with your finger.

then press right touchpad button
once

Drag

16 Users Manual

Move an object, or select an area
or multiple objects

Place the pointer over an object or
on a starting location.
While pressing the left touchpad
button, press down on the
touchpad and slide your finger to a
destination or ending location.

Action Function Process

Scroll Display upper/lower/left/right part

of the content within a window

(Applicable to only some
programs)

Place your finger on the scroll
wheel, and roll the wheel up or
down.

Or, place your finger on the right
edge or bottom edge of the
touchpad and move vertically or
horizontally.

If the mouse pointer does not move smoothly when a PS/2 mouse is

connected

When a PS/2 mouse is connected, the mouse pointer may not move smoothly

or move irregularly. In those cases, click Start > Control Panel > Add/

Remove Programs. Then, check whether the Synaptics ToutchPad program

is installed. If not installed, install the Synaptics TouchPad program using the

System Software CD.

Make sure to use your finger to move the pointer with the touchpad. Do not

use any sharpened tool because it will damage your touchpad.

If you want to use fully the various functions of the touchpad and touchpad

buttons, refer to and adjust mouse-related settings on Control Panel.

The PS/2 Mouse item should be set to 'Enabled' on the Advanced menu of

System Setup to use both touchpad and mouse at the same time.

When the computer awakes from the standby mode or hibernation mode, the

touchpad may not operate smoothly. This problem may occur during

initialization of the touchpad. After a while, it will operate normally.

If the touchpad tapping function does not work on Windows 98, first check

whether the touchpad driver is installed.

If the driver is installed and the touchpad tapping function does not work,

adjust the settings as follows.

Click Start > Settings > Control Panel > Mouse > Advanced. Select the

"Use tapping" option. Then, the touchpad tapping function will operate

normally.

Using the Touchpad 17

Reading the Status Indicators

Number Lock LED

Scroll Lock LED

LED Name Function

HDD Access Blinking Blue - HDD is being accessed.

CD Access Blinking Blue - CD is being accessed.

Num Lock Changes a portion of the keyboard to a numeric keypad.

Caps Lock Changes all alpha or letter input into capital letters.

Scroll Lock Scroll lock in certain software.

Power Green - System power on.

Battery Green - No battery pack installed/battery fully charged.

See ”Using the Numeric Keypad” on page 12.

No changes occur to numeric and special keys.

Blinking - Standby mode.

Amber - Charging.
Blinking - Bad Battery

Caps Lock LED

CD Access LED

HDD Access LED

Battery LED
Power LED

18 Users Manual

Using The Computer

Using the Floppy Disk Drive (Option)

You can purchase an external floppy disk drive to use with your computer.

To insert a floppy disk

To use the floppy disk drive, install the appropriate driver in the FDD drive

installation CD provided with your floppy disk drive.

1. Connect the floppy disk drive’s USB cable to the USB port of your computer.

2. Insert a floppy disk with the label facing up until the eject button pops out.

Eject Button

To eject a floppy disk

1. Stop any process that accesses the floppy disk drive and ensure the FDD access
LED is turned off.

2. Press the eject button and the floppy disk pops out. Remove the floppy disk.

If you remove the floppy disk when the FDD access LED is on, the disk and
the data in it may be damaged.

Using The Computer 19

Using the CD Drive

You have one of following drives installed on your computer.

• CD-ROM drive: You can read a CD.

• CD-RW drive: You can read and write a CD.

• DVD-ROM drive: You can read a CD/DVD.

• CD-RW/DVD-ROM combo: You can read a CD/DVD and write a CD.

To insert a CD

1. Press the eject button on right side of the CD drive.

2. When the tray slides out, place a CD onto the tray with the label facing up, and

push the CD down until it clicks.

Eject Button

3. Push the tray in gently until it clicks.

To eject a CD

1. Stop any process that accesses the CD drive and ensure the CD access LED is

2. Press the eject button on right side of the CD drive.

3. When the tray slides out, remove the CD from the tray.

4. Push the tray in gently until it clicks.

20 Users Manual

turned off.

CD Access LED

Emergency Eject
Hole

If you remove the CD when the CD access LED is on, the disk and the data in
it may be damaged.

Emergency Eject Hole

To eject a CD when the CD drive is not working or the computer is turned off,
unfold a paper clip, and insert the unfolded end of the clip into the emergency
eject hole and press until the CD tray opens.

To clean a CD or DVD title

Clean the disc with a soft clean cloth by wiping from the center outwards.

To play a DVD

You have to install the DVD software provided on a separate CD to view a
DVD title.

To use the Windows Media Player

The Windows Media Player allows you to play audio and video files from the computer
or the Internet.

To launch the Windows Media Player, click Start > All Programs > Accessories >
Entertainment > Windows Media Player.

Features

Playback Control Area

Playlist

Using The Computer 21

Windows Media Player tour

For more information about using the Windows Media Player, run the
Windows Media Player and click Help > Help Topics > Windows Media

Player tour.

To play a video CD

If a video CD does not run automatically, follow these steps.

1. Insert a video CD into the CD drive.

2. When the CD drive window appears, double-click the MPEGAV folder.

3. Double-click the .dat file.

4. When the [Caution] dialog appears, click Open With.

5. Select “Select the program from a list” and click OK.

6. Select the Windows Media Player, and click OK. The video starts playing.

Above procedure applies only to the video CDs that has a .dat file as the
execution file. Playing procedure may be different according to video CDs.

To control the volume

Using the keyboard:

Press <Fn>+<PgDn> or <Fn>+<PgUp> to adjust volume.

Using the volume control program:

Click the Volume icon ( ) on the taskbar, and adjust the slide bars.

Or, double-click the Volume icon ( ) on the taskbar, and adjust the settings in the
[Master Volume] dialog.

22 Users Manual

To display the Volume icon on the taskbar
Click Start > Control Panel > Sound, Speech, and Audio Devices >
Sounds and Audio Devices. On the Volume tab, select “Place volume icon
in the taskbar” check box and click OK.

To write data on a CD (Option)

If you have CD-RW drive or CD-RW/DVD ROM combo drive installed on your
computer, you can write data on a CD.

This function is provided in Windows XP only. Install the CD writer software
provided on a separate CD to write a CD in other operating systems.

You cannot write on a CD that already has data in it.

1. Insert a blank CD into the CD drive.

2. On the [CD Drive] dialog, select Open Writable CD Folder and click OK. The

CD drive window appears.

3. Click Start > My Computer.

4. In My Computer window, select files and folders to copy, then drag and drop them

onto the CD drive window.

My Computer window

4. Drag and drop folders or
files to copy.

5. Click Write these files to CD.

CD drive window

Using The Computer 23

5. Click Write these files to CD in the CD drive window.

6. When the CD Writing Wizard appears, enter the CD label, and click Next. The

data begins copying.

7. When copying is completed, a message ‘completed’ appears and the CD drive
window opens automatically.

For more information on writing CDs

Click Start > Help and Support. Type “CD copy” in the search field, and click
the Search icon ( ).

To create an audio CD

Run the Windows Media Player program, click the Help > Help Topics. Click
Using Windows Media Player > Using CDs > Creating your own CDs > To
create your own CD.

24 Users Manual

Enjoying Home Theater (S/PDIF Port)

Your computer supports 5.1 channel output, which is a basic function for home theater
systems, and DVD drives. It provides 3D surrounding sound and vivid screen.

What is a home theater system?

Home theater system usually consists of a TV, DVD, 5.1 channel speaker, and
digital amp and provides a high-resolution screen (MPEG2) and 3D
surrounding sound (Dolby 5.1 or DTS). With a home theater system, you can
enjoy a vivid screen and sound in your home as if you are in a movie theater.

Following devices is required to enjoy a home theater system.

• 5.1 channel speakers including amplifier and connection cables (Purchased

separately)

• DVD drive and program

• TV output port on your computer

When purchasing a 5.1 channel speaker, make sure it supports S/PDIF
(optical) port.

You need a CD/DVD that supports 5.1 channel to enjoy the 5.1 channel
speaker system.

To use home theater system, complete the following procedures:

• Step 1. Connect digital amp and speakers to the computer.

• Step 2. Enable S/PDIF port on the computer.

• Step 3. Enable S/PDIF on the DVD program.

Using The Computer 25

Step 1. Connect digital amp, speakers, and TV to the computer

1. Connect a digital amp to the S/PDIF port of your computer.

Headphone / S/PDIF Port

2. Connect speakers to the digital amp.

Digital Amplifier

Front Left Speaker

Surround Left Speaker Surround Right Speaker

Computer

TV

Center

Speaker

Sub

Woofer

Front Right Speaker

Step 2. Enable S/PDIF port on the computer

1. Click Start > Control Panel > Sounds, speech, and Audio Devices > Sounds

2. On the Volume tab, click Advanced in the Device volume area.

3. On the [Master Volume] dialog, click Options > Advanced Control to display the

4. Click Advanced, select “S/PDIF” check box, and click OK.

26 Users Manual

To watch through a TV

Connect the TV and change the setting in the Display Properties to TV. See
“Using External Display Devices” on page 73.

and Audio Devices.

Advanced button.

Step 3. Enable S/PDIF on the DVD program

To use 5.1 channel speakers, you need to install the Power DVD program from the
DVD Installation CD provided with your computer, then change the settings as
following procedure.

1. Run Power DVD program and click the Settings icon ( ).

2. On the Audio tab, set the Audio Output setting to “Use SPDIF” and click OK.

Now, you can enjoy home theater using DVD titles.

If you have enabled S/PDIF on the DVD program, sound will not be output to
the built-in speaker and the headphone terminal.

To control volume for your 5.1 channel speaker, use the control on the digital
amp. (Please refer to the speaker manual.)

Using The Computer 27

Using the PCMCIA Card Slot

Various different functions can be added by inserting PCMCIA cards into the system.
This system supports 16/32 bit, type I or II PCMCIA card types.

The PCMCIA card slot does not support a ZV card or a PCMCIA III card.

To insert a PCMCIA card

Before using the PCMCIA slot, remove the slot protector.

Push the eject button of the PCMCIA card slot once to pop it out. Push the
button again to eject the slot protector.

1. Insert a PCMCIA card into the PCMCIA card slot on the side of the computer.

Eject button

2. Windows automatically installs the necessary driver for the card. If there is no

28 Users Manual

available driver found by Windows, you have to install the driver using a disk
supplied with the card.

To remove a PCMCIA card

1. Double-click Safely Removes Hardware icon ( ) on the taskbar.

2. On the [Safely Remove Hardware] dialog, select the appropriate PCMCIA card
and click Stop.

3. When [Stop a Hardware Device] dialog appears, click OK.

4. Click Close to close the [Safely Remove Hardware] dialog.

5. Push eject button of the PCMCIA card slot once, then the button pops out.

Eject button

6. Push the button again to eject the PCMCIA card.

Using The Computer 29

Connecting to the Internet

Connecting with a Modem

Before Start:

• Prepare a telephone line that is not digital.

• Contact an internet service provider (ISP) for instructions on how to connect to

and disconnect from the Internet, and fees.

1. Connect a telephone line to the computer’s modem port.

2. Connect to the Internet according to the instructions provided by your ISP.

30 Users Manual

If the Internet connection is not disconnected properly, additional telephone
charges may be imposed.

Connecting Through a Wired LAN

1. Connect a LAN cable to the computer’s LAN port.

2. Click Start > Control Panel.

3. Click Network and Internet Connections in the [Control Panel] window.

4. Click Network Connections in the [Network and Internet Connections] window.

5. Right-click the Local Area Connection icon and click Properties.

Connecting to the Internet 31

6. On the General tab, select “Internet Protocol(TCP/IP)” and click Properties.

Intel(R) Pro/100 VE Network Connection

7. If your network environment supports DHCP:

On the General tab, select “Obtain an IP address automatically” and “Obtain DNS
server address automatically” and click OK.

If you want to use a static IP:
On the General tab, select “Use the following IP address” and fill in the IP
address, Subnet mask, Default gateway, Preferred DNS server, and Alternative
DNS server fields. Click OK.

32 Users Manual

To use both DHCP and static IP simultaneously

When you are alternatively using networks with either DHCP or static IP addressing,
you can use both of the network connections without reconfiguring using alternative
settings that enable simultaneous configurations of DHCP and static IP.

This function is provided only when your operating system is Windows XP.

1. Click Start > Control Panel > Network and Internet Connections > Network
Connections > Local Area Connection, press the right button of the touchpad,
and then select Properties.

2. Select the Internet Protocol (TCP/IP) item, and then click Properties.

3. In the Alternate Configuration tab, click User configured, and then enter the

appropriate values for the following: IP address, Subnet mask, Default gateway,
Preferred and alternate DNS server, and Preferred and alternate WINS server.

4. When the configuration has been completed, click OK.
Now you can connect to both networks using DHCP and static IP respectively.

Connecting to the Internet 33

Connecting Through a Wireless LAN

A wireless network (Wireless LAN) environment is a network environment that
enables communication between multiple computers at home or a small-size office
through wireless LAN devices.

Using the wireless network connections between the systems, you can use normal
network functions such as sharing of files, folders and printers. Using computer-to­computer network (ad hoc) connections, you can access the Internet through a
computer connected directly to the Internet even if your computer is not directly
connected to the Internet. For details, see “Using Network Services” on page 44

The information provided in this section only applies to models equipped with
an optional wireless LAN device.

Wireless network connections can be classified into two categories.

1) Access Point

You can connect to an AP to use the network. This is possible only in an environment
equipped with an AP. For details, see “Connecting to an Access Point (AP)” on page 35

What is an Access Point (AP)?

An AP is a network device that bridges wired and wireless LANs, and
corresponds to a wireless hub in a wired network. You can connect multiple
wireless LAN installed computers to an AP.

2) Computer-to-computer (ad hoc)

This is also called a peer-to-peer or ad hoc network.

In computer-to-computer wireless networks, you can wirelessly connect 2 or more
computers that have wireless LAN modules. Using computer-to-computer wireless
networks, you can access the Internet through a computer that is connected to the
Internet even if your computer is not directly connected to the Internet. For details, see
“Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 36

34 Users Manual

Connecting to an Access Point (AP)

This section describes how to connect to an AP. You can use the network when you are
connected to an AP.

In this section, the configuration procedures are described for Windows XP
installed computers. For information on the configuration procedures for other
operating systems, see “Using Wireless Networks in Other Operating
Systems” on page 41 Please ask your network administrator about detailed
configuration information such as the network key (encryption key).

1. Right-click on the Wireless Network Connection ( ) icon on the taskbar, and
select View Available Wireless Networks.

2. Select your desired AP (e.g. Test) to connect, and enter the encryption key for the
AP in the Network key field, and click Connect.

If the network key is not configured for the desired AP, select 'Allow me to
connect to the selected wireless network, even though it is not secure’.

Now you are connected to the AP, and you can access the network.

Connecting to the Internet 35

Checking the connection status

Move the mouse pointer over the Wireless Network Connection ( ) icon on
the taskbar, and the connection status is displayed.

Connecting to computer-to-computer networks (peer-to-peer or

ad hoc)

In computer-to-computer wireless networks, you can wirelessly connect 2 or more
computers that have wireless LAN modules.

You can connect by completing the following steps:

• Step 1. Set up a computer-to-computer network on a computer.

• Step 2. Connect to the configured computer from other computers.

In this section, the configuration procedures are described for Windows XP
installed computers. For information on the configuration procedures for other
operating systems, see “Using Wireless Networks in Other Operating
Systems” on page 41

36 Users Manual

Step 1. Setting up a computer-to-computer network

1. Right-click on the Wireless Network Connection ( ) icon on the taskbar, and
select View Available Wireless Networks.

2. Click Advanced.

3. On the Wireless Network tab, click Advanced.

4. Clear 'Automatically connect to non-default network' check box, if it is selected.
Select 'Computer-to-computer (ad hoc) networks only', and click Close.

5. In the Wireless Networks tab, click Add.

Connecting to the Internet 37

6. Enter the network name (e.g. samsung), and unselect 'The key is provided for me
automatically'. Enter the encryption key in the Network key field, and click OK.

To prevent a network connection from an unauthorized user, it would be better
to configure a network key (encryption key). A network key consists of 5 or 13
alphanumeric characters (e.g. magic), or of 10 or 26 hexadecimal numbers (a
hexadecimal number is represented by numbers '0' to '9' or letters 'a' to 'f').

38 Users Manual

7. Check that the configured network name (e.g. samsung) is in the ’Preferred
networks’ item, and click OK.

Now your wireless network setup has been completed.

Step 2. Connecting to the configured computer

1. Right-click on the Wireless Network Connection ( ) icon on the taskbar, and
select View Available Wireless Networks.

2. Select the wireless network name (e.g. samsung) specified in ”Connecting to
computer-to-computer networks (peer-to-peer or ad hoc)” on page 36, enter the
encryption key in the Network key field, and then click Connect.

Connecting to the Internet 39

If the network key is not configured in ”Connecting to computer-to-computer
networks (peer-to-peer or ad hoc)” on page 36, select 'Allow me to connect to
the selected wireless network, even though it is not secure'.

The two computers are connected and are able to communicate with each other. When
the computers are connected, the 'Wireless Network Connection' message is displayed
for a short time over the Wireless Network Connection icon of the two computers.

Checking the connection status

Move the mouse pointer over the Wireless Network Connection ( ) icon on
the taskbar, and the connection status is displayed.

40 Users Manual

Using Wireless Networks in Other Operating Systems

To use wireless LAN on other operating system except Windows XP, you should
install the MagicLAN program and configure the networking settings.

Installing MagicLAN program

1. Insert the System Software CD into your CD drive.

2. Click Start > Run. Then click Browse and locate the wireless LAN setup program

and click OK.
Program location: D:\Application\Wireless\LanSetup.exe
(Assumed that the CD drive is labeled with "D:".)

3. Follow the directions displayed on the screens to complete the installation.

4. Restart your computer.

Configuring networking settings

1. Click the MagicLAN Utility ( ) icon on the taskbar. If it is not displayed on the
taskbar, click Start > Programs > MagicLAN > MagicUtility > MagicLAN

Utility.

2. Click Yes on the [WLAN Configuration Utility] dialog, and then click Next on the

[Profile Wizard - Step 0/6] dialog.
If the [WLAN Configuration Utility] dialog does not appear, click Profile and
click New.

3. Type appropriate name and description in the Profile Name and Description
fields on the [Profile Wizard - Step 1/6] dialog, and click Next. For example, type
"SAMSUNG" in the Profile Name field.

4. Set the Operating Mode for the wireless network to use on the [Profile Wizard -
Step 2/6] dialog, and then click Next.

• To connect to a computer-to-computer network: Select "802.11 Ad-hoc".

• To connect to an access point (AP): Select "Infrastructure".

Connecting to the Internet 41

5. Click Survey on the [Profile Wizard - Step 3/6] dialog, and select an accessible AP
(for Infrastructure mode) or a computer-to-computer network (for 802.11 Ad-hoc
mode). Click Next.

• To create a computer-to-computer network:

Type a network name (SSID) to use for a computer-to-computer network in
the SSID field. For example, type "p2p" and then click Next.

• To connect to a computer-to-computer network:

To connect to a computer-to-computer network already created, double-click
the network on the "Stations in range" list. For example, double-click the
network named "p2p" on the list.

• To connect to an AP (Access Point):

Double-click the AP to use on the "Access Points in range" list.

6. If you want to set the security key (WEP key), select a value (either 40 bit or 104
bit) for WEP Mode on the [Profile Wizard - Step 4/6] dialog.

• Procedure for Setting Security Key :

1. Select either 40-bit or 104-bit for WEP Mode.

2. Type the WEP key to use to connect to the computer-to-computer network
or the AP (Access Point) in the corresponding key input field .

3. Click Next.

We recommend to set a security key (WEP Key). For 40-bit, you should input
either a 5-characters long ASCII string or a 10-digit long hexadecimal value.
For 104-bit, you should input either a 13-characters long ASCII string or a 26­digit long hexadecimal value. The computers and access points on the
network must use the same security key. For setting the security key for
access points, consult your network administrator.

42 Users Manual

This version does not support the "Generate WEP key using Passphrase"
function.

7. Set IP address on the [Profile Wizard - Step 5/6] dialog, and click Next.

• To obtain IP address automatically (DHCP)

Select the "Obtain an IP address automatically" check box.

• To use a static IP address

Select the "Use the following IP address "check box, and type IP Address,
Subnet Mask, Default Gateway, Primary DNS, and Secondary DNS. (For
more information, consult your network administrator.)

8. The settings you selected is displayed on the [Profile Wizard - Step 6/6] dialog.
Select "After creating the profile, apply this setting." check box and click Finish.

9. In case of creating the profile for a computer-to-computer network, the "In the Ad­hoc mode…. " dialog may be displayed after profile creation. Click Yes to
complete the setup.

For more information, press <F1> to see the Help files.

Connecting to the Internet 43

Using Network Services

While the computer is connected to the network, you can use network services to share
files, folders, and printers. Using computer-to-computer wireless networks, you can
access the Internet through a computer that is connected to the Internet even if your
computer is not directly connected to the Internet.

Network services are provided for the computers that are connected to the
network through wired or wireless network connections. For details, see
“Connecting Through a Wired LAN” on page 31 and see “Connecting Through
a Wireless LAN” on page 34

Sharing files or folders

This section describes how to share files and folders between computers connected to
the network.

To share files, complete the following procedures:

• Step 1. Configuring the sharing of files and folders on a computer.

• Step 2. Accessing shared files and folders from another computer.

When a file or folder is shared, anyone connected to the network can open and
delete the shared file or folder.
Configure a file sharing network only when the network is secure, and do not
share important data.

44 Users Manual

Step 1. Configuring Sharing

1. Right-click the target file or folder to share in My Computer, and select Sharing
and Security.

2. Click 'IF you understand the security risks but want to share files without running

the wizard, click here'.

It has the same security effect as that of the 'Network Setup Wizard'.
This screen does not appear if Internet Sharing Network Wizard has been
installed in the computer-to-computer wireless network environment.

3. Select 'Just enable file sharing', and click OK.

4. In the 'Network sharing and security' field, select 'Share this folder on the network',
enter the share name, and click OK.

Be cautious when selecting 'Allow network users to change my files' since
other network users can change the files in the shared folder.

The file and folder sharing configuration has been completed.

Connecting to the Internet 45

Step 2. Using Shared Files or Folders

This section describes how to access shared files or folders if your computer is a
member of the same workgroup.

1. Click Start > My Computer. Under Other Places, click My Network Places in
your computer.

2. Click 'View workgroup computers', and click the desired computer to access the
shared file.

If your computer is a member of another workgroup:

1. Click Other Places > Microsoft Windows Network.

2. Click the desired workgroup.

3. Click the desired computer to display the shared files or folders.

Sharing Printers

This section describes how to share a printer between computers connected to a
network.

To share a printer, complete the following procedures:

46 Users Manual

• Step 1. Configure printer sharing in the computer connected to the printer.

• Step 2. Add and use the shared printer in other computers on the network.

Step 1. Configuring Printer Sharing

1. From the computer connected to the printer, click Start > Printers and Faxes.

2. Right-click the printer you want to share, and click Sharing.

3. Select 'Share this printer', enter a share name for the shared printer, and click OK.

4. In the Printers and Faxes window, you will find the printer icon has been changed

to another icon on a hand.

Step 2. Adding and Using a Shared Printer.

1. From a different computer that wants to use the shared printer, click Start >
Printers and Faxes.

2. Click Add a printer.

3. In the Add Printer Wizard, click Next.

4. Select 'A network printer, or a printer attached to another computer', and click
Next.

Connecting to the Internet 47

5. Select 'Browse for a printer', and click Next.

6. Select the workgroup or computer, select the desired printer, and click Next.

If you cannot find the desired printer, try again after a while.

7. Read the warning about a shared printer, and click Yes to install the shared printer.

8. Select Yes for 'Do you want to use this printer as a default printer?', and click Next.

9. Click Finish.

10. When the printer sharing configuration has been completed, the shared printer

appears in the Printers and Faxes window.

48 Users Manual

Now you can print using the shared printer even if your computer is not directly
connected to a printer.

Sharing an Internet Connection

Using computer-to-computer (peer-to-peer) network connections, you can access the
Internet through a computer connected to the Internet even if your computer is not
directly connected to the Internet.

To share an Internet connection, the computers should be connected to a
computer-to-computer (peer-to-peer) wireless network. For details, see
“Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on
page 36
Also, one of the computers has to be connected to the Internet (external
network).
The configuration procedure to share an Internet connection are described for
Windows XP installed computers.

To share an Internet connection, complete the following procedures:

• Step 1. Configuring a Internet connection sharing from the computer connected

to the Internet.

• Step 2. After completing the shared Internet connection configuration, check

that the other computers can access the Internet through the shared Internet
connection.

Step 1. Configuring Internet Sharing.

Configuring a shared Internet connection on the computer connected to the Internet.

1. Click Start > Control Panel > Network and Internet Connections > Network
Connections.

2. Right-click on the device connected to the Internet, the external network, and

select Properties.

Connecting to the Internet 49

If the computer is connected to the Internet through a wired LAN, select 'Local
Area Connection'.

3. On the Advanced tab, select 'Allow other network users to connect through this
computer's Internet connection', and click OK.

Step 2. Checking the Shared Internet Connection.

When the Internet connection sharing configuration has been completed, the network
icon in the Network Connections window is displayed as follows:

Click Start > Control Panel > Network and Internet Connections > Network
Connections.

– A computer connected to the Internet.

If the icon does not appear after a long time, restart the computer.

50 Users Manual

– A computer sharing the remote Internet connection (other computer).

Computers on the network can access the Internet through the shared Internet
connection only when the computer connected to the Internet is turned on.

Using the Battery

Your computer uses a smart rechargeable Lithium-ion (Li-ion) battery pack for power
when the AC adapter is not attached to an electrical outlet. The smart battery gives a
accurate measurement of the current battery capacity which helps extend operating
time by enabling effective power management in operating systems that take
advantage of the accurate information supplied by the battery.

Charging the Battery

Your computer’s battery starts charging automatically when you connect the power to
the computer and to an electrical outlet. If the computer is off, the battery charges faster
than if the computer’s power is on.

Approximate charging times for the Li-Ion battery are:

• 4 hours with the computer off.

• 10 hours with the computer on.

While the battery is charging normally, the battery charge light on the computer is
amber. When the battery is fully charged, the light changes to green.

When you use a new battery pack for the first time or use a battery after a long period
of storage, the initial battery life is shorter than normal. Normal battery life resumes
after a few discharge-recharge cycles.

Follow these rules for charging your battery:

• A battery normally discharges power when not used for long periods of time.

Be sure to recharge the battery every two months when it is not in use.

• Make it a practice to discharge your battery fully before recharging the battery.

This can help extend the life of the battery.

• Do not attempt to charge the battery in temperatures of under 0

o

C or over 45oC

All batteries eventually wear out and lose the ability to hold a charge. You may
need to replace your battery pack after a year of average usage.

Using the Battery 51

Safely Using the Battery

Follow these guidelines to safely use the battery:

• Turn off your computer and unplug it if you accidentally:

– Expose the equipment to liquid.

– Drop, jar, or damage the computer.

• Do not disassemble the battery, heat it above 100°C, or burn it. The battery

used in this computer may cause a fire or chemical burn if mistreated.

• Your computer's rechargeable battery may be considered hazardous waste. If

you replace your battery with a new one:

– Keep the old battery out of the reach of children.

– Dispose of the old battery promptly.

– Make sure that you follow all local requirements when you dispose of the

old battery.

Removing and Installing a Battery

1. Turn off the computer and close the LCD.

2. Turn the computer over so the bottom of the computer faces up.

3. While sliding the battery latch inward, slide the battery compartment cover up and

off the computer.

4. Pull the battery out using a band on the battery.

5. To install the battery again, insert the battery with product information facing

52 Users Manual

down. Close the battery compartment cover.

Monitoring the Battery Charge

Battery life is affected by factors such as the power management settings in System
Setup, the applications you use, and the brightness settings of the LCD. Under normal
usage, the battery charge lasts approximately 2 hours.

Battery life estimates are subject to variation. The actual life of your battery
may be less than the estimates given in the manual.

CPU speed when using the battery

When the computer is running on battery power, CPU operation speed is
adjusted automatically to extend the battery operation time.

To use the power meter

Click Start > Control Panel > Performance and Maintenance > Power Options >
Power Meter tab to display the power meter. You can check the current power source

and total battery power remaining.

Using the Battery 53

To use the indicators on the battery

Remove the battery from the computer and press the PUSH button on the side of the
battery to display the battery power remaining.

PUSH button

Battery Warnings

If the battery charge is low (about 10%) you have 5–10 minutes of battery life left. You
should:

• Save your work and,

• Connect the power cord to the computer or turn off the computer and install a

fully charged battery.

You can adjust the battery alarm features by using the operating systems power
management program (Start > Control Panel > Power Options in Windows).

If you cannot run your computer from the battery and the battery will not charge when
you attach the power cord, the problem may be that:

54 Users Manual

• The battery temperature is below 0°C or over 45°C. If you think the battery

temperature is too hot or too cold, turn off the computer, remove the battery,
and let the battery reach room temperature. Then try charging the battery again.

• The battery may be defective, please try running your system from the AC

adaptor with the battery removed from the system. Please contact the Samsung
helpline if you are unsure.

To extend the battery’s life span

When the battery is in continuous use without being completely charged or discharged,
there may be a difference between the displayed battery charge and the actual battery
charge, owing to the inherent characteristics of the battery.

Battery calibration process, which is completely discharging the battery and fully
recharging it, can correct this problem.

1. Turn off the computer and disconnect the AC adapter.

2. Turn on the computer and press <F2> to enter System Setup.

3. Select Smart Battery Calibration in the Boot menu, and press <Enter> to start.

The calibration process usually takes 3 to 4 hours depending on the remaining
battery charge.

4. When the calibration process is complete and the battery is completely discharged,
connect the AC adapter to fully recharge the battery.

Using the Battery 55

Using System Setup

The System Setup (BIOS) program enables you to configure your computer hardware
and set security and power-savings options. The settings you choose are stored in
battery-maintained CMOS memory that saves the information even when the
computer’s power is turned off. When your computer is turned back on, it is configured
with the values found in this memory.

Run System Setup if you get a message prompting you to run the program. You may
also want to run System Setup, particularly the first time you use your computer, to set
the time and date, use security or power-management features, or alter the settings of
other features.

BIOS Caution:

If you are not familiar with BIOS setup and what the parameters mean, seek
help from a person who is knowledgeable. Incorrect settings may cause your
system to “Crash”.

Your computer’s version of System Setup may not include all the fields listed
here or may include additional fields. Field names and order of appearance
can vary according to the version of the BIOS (basic input/output system) on
your computer.

Starting System Setup

To start System Setup, turn on your computer and then press <F2> and hold until the
System Setup screen appears.

To open the menu you need to use, use the left or right arrow keys to select the menu
name.

56 Users Manual

Table 2. System Setup Menus

Menu Function

Main Changes the basic system.

Advanced Configures advanced features on your computer.

Security Enables security features, including passwords.

Boot Specifies the order of boot devices and configures boot

Exit Specifies how to exit System Setup.

features.

Table 3. System Setup Navigation Keys

Navigation Key Function

<F1> Displays the General Help window.

<Esc> Exits the current menu.

<Left Arrow> or
<Right Arrow>

<Up Arrow> or
<Down Arrow>

<F5> or <F6> Changes Values

<F9> Sets the parameters for the current menu to their default values.

<F10> Save changes and exit system setup.

<Enter> Executes commands or opens a submenu.

Selects different menus.

Moves the cursor up and down between fields.

Using System Setup 57

Changing Booting Priority

The Boot menu in System Setup enables you to select the booting device and to set
booting options.

Boot Device Priority field enables you to select the order in which the computer
attempts to boot from different devices. The field has 3 options: DVD/CD-ROM

Drive, Removable Devices and Hard Drive.

To change the booting device priority, choose the device positions by completing
the following:

1. At startup, press <F2> to open System Setup.

2. Use <Right Arrow> to select Boot menu.

3. Press <Enter> on Boot Options.

4. Highlight the 1st Boot Device option with <Up Arrow> or <Down Arrow> keys.

5. Press <F5> or <F6> until the option is moved to the desired position.

6. Press <F10> to exit and save your changes.

7. Press <Enter> again to restart the computer.

58 Users Manual

Configuring the Password

Setting the Supervisor Password

By configuring a supervisor password, you can restrict system access to authorized
users only.

1. Select the Security menu in the System Setup. To enter System Setup, see “Using
System Setup” on page 56.

2. On the Set Supervisor Password item, press <Enter>.

3. Enter a password, press <Enter>, re-enter the password for confirmation, and
press <Enter> again.

4. When a message confirming the password configuration appears in the [Setup
Notice] window, press <Enter>.

Setting the User Password

You can configure user passwords so that other users can use the system.

Before configuring a user password, a supervisor password must have been
configured.
Users can start the system with their user password, but cannot enter into the
System Setup.
Deactivating the supervisor password also deactivates the user password.

On the Set User Password item, press <Enter>, and complete step 3-4 of "Setting the
Supervisor Password".

Configuring the Password 59

Activating the Booting Password

Before activating the booting password, the supervisor password must have
been configured.

Set the Password on boot option to [Enabled].

From now on, system booting will not proceed without the password.

Deactivating the Password

1. On the password to delete, press <Enter>. (e.g. supervisor password)

2. Enter the current configured password, and press <Enter>.

3. Leave the 'Enter New Password' and 'Confirm New Password' field empty, and
press <Enter> to deactivate the password.

60 Users Manual

Using Power Management Options

Your computer includes Power Management options that can help the battery charge
last longer and extend the life of the battery. Power management options will slow
down or shut off system components when the components are not being used.

Power management may slow down system performance. Your computer runs fastest
with the power cord attached, when power management is disabled.

In the next sections, basic and advanced methods of power management will be
discussed.

Basic Power Management Schemes

This section discusses the basic schemes of power management when the computer is
operating on battery power or using AC power.

Standby vs. Hibernation

Hibernation is a state where the contents of memory are stored in a special file
on the hard disk, and Standby simply keeps a small holding current through
the memory to keep the data. You are more likely to sustain loss of data in
Standby mode so it is recommended to save all open files before entering
Standby.

Changing Devices:

Do not change PC Cards while in standby or hibernate modes.

To enter the power management window complete the following:

1. Click Start > Control Panel > Performance and Maintenance.

2. Click icon to display the Power Options Properties window.

Using Power Management Options 61

3. Click the Power Schemes tab to display the basic power management options.

Power Schemes Tab

4. Select the time that you wish each of the following actions to occur in Battery and
AC power mode.

• Turn off monitor:

• Turn off hard disks:

• System standby:

• System hibernates:

Turning off the monitor and HDDs will save a substantial battery power, therefore
when in battery only mode select the shortest time practical.

a Hibernate Mode (Power Management or Manual Method)

62 Users Manual

When hibernation is used, your computer turns off and when you power up again,
everything is restored exactly as you left it—including programs and documents
you may not have saved or closed. Everything in memory gets saved to the HDD,
and the monitor and hard disk get turned off.

If You Reinstall Windows

You should re-establish hibernate in power options by opening Power Options
Properties window and click on the Hibernate tab then click “Enable
Hibernation”.

Hibernate Tab

Frequent Interruptions:

If you experience frequent interruptions, you might also consider putting your
computer into automatic hibernation after a specified number of minutes using
the power management options.

a Standby Mode (Power Management or Manual Method)

Standby is used mainly for conserving battery power in your notebook computer. It
also gives you the benefit of getting right back to your work without waiting for the
computer to restart. Standby turns off your monitor and hard disks, placing your entire
system in a low-power state. When you return to your computer, restores your desktop
exactly as you left it. It is recommended that you do not enter standby mode with less
than 20% battery power.

5. Click OK to set your power management options and close the window.

Standby Key:

The manual <Fn+F4> key combination will not activate Standby or Hibernate
modes whilst you are playing a multimedia program or have an active USB
device connected.

Using Power Management Options 63

Advanced Power Management Schemes

This section discusses the advanced power management schemes. There are two
buttons that you can use to manually conserve power.

To enter the power management window complete the following:

1. Click Start > Control Panel > Performance and Maintenance.

2. Click icon to display the Power Options Properties window.

3. Click the Advanced tab to display the advanced power management options.

Advanced Tab

Power & Sleep Button
Programming Windows

4. Select the mode (Do nothing/Ask me what to do/Standby/Hibernate/Shut

5. Click OK to set your power management options and close the window.

You can return to normal operation after you have used one of the “Power
Management” buttons by quickly pushing and releasing the Power button.

64 Users Manual

down) assigned to the Power button and/or Standby <F4> key. Closing the lid is
the same as pushing the Sleep button.

The “Standby” key is assigned to the <Fn+F4> key combination. See ”Basic
Power Management Schemes” on page 61 for a better understanding of
Standby and Hibernate modes.

Using the Hard Drive

Your computer includes a removable IDE (integrated drive electronics) hard drive. The
IDE hard drive can store the data and programs your computer uses. The drive plugs
into a connector on the system board.

The hard drive that comes with your computer has already been formatted. Do
not format the hard drive. Doing so destroys all data contained on the drive. If
you need to format a new drive, or want to erase all data on your existing hard
drive, refer to the online manual for your operating system.

Removing the Hard Drive

To prevent loss of data and damage to the disk, do not remove the hard drive
while the computer’s power is on and do not drop or jar the hard drive.

To remove the hard drive from the computer:

1. If you are installing a new hard drive, backup the application and data files on the

old hard drive before removing it from the computer.

2. Turn the computer’s power off.

3. Close the LCD panel, and turn the computer over so that the bottom of the unit

faces up.

4. Remove the screw that holds the hard drive in place.

Hard-drive

Bottom of computer

5. Pull the hard drive out of the computer.

Using the Hard Drive 65

Installing a Hard Drive

To install a hard drive:

1. Remove the old hard drive from the computer as described in the previous section.

2. Remove the 4 HDD retaining screws to remove the old HDD from the drive

bracket.

3. Place the new HDD into the drive bracket and the replace the 4 retaining screws.

4. Slide the new drive into the hard drive compartment. Make sure the drive is pushed

back as far as it will go.

5. Install the screw that holds the hard drive in place.

6. If required, install windows and appropriate device drivers according to the

instructions below. For details, see “Reinstalling Windows XP” on page 92 and
”Reinstalling Software” on page 90.

66 Users Manual

Memory Modules

You can increase system memory by installing optional memory modules.

To avoid possible system problems, use only approved memory modules in
your computer. Please consult the appropriate sections of this manual,
Samsung Technical Support, or the support website (www.samsungpc.com)
for additional information.

Before You Install Memory

To prevent personal injury and damage to the equipment, follow the
precautions listed here before installing a memory module.

Take the following precautions when installing a memory module:

• Before you start this process, turn off the computer, unplug the power cord, and

remove the battery. Also, disconnect any external devices.

• Before handling a memory module, discharge any static electricity by touching

a grounded surface or using a grounding wrist strap.

• Do not insert objects with conductive material, such as metal screwdrivers or

graphite pencils, into the memory-module compartment.

• Be careful in handling the metal plate of the memory door.

Memory Modules 67

Installing a Memory Module

Handle a memory module carefully. Hold them only by the edges.

To install a memory module:

1. Close the LCD and turn the computer over so that the bottom faces up.

2. Using a screwdriver, remove the screw that holds the keyboard in the hole labeled

“KBD”.

3. Turn the computer over so the keyboard is up and open the LCD cover.

68 Users Manual

Keyboard Removal

Use extreme care when removing the keyboard because it may be easily
damaged. Also take care when lifting out the keyboard, not to damage the
keyboard output ribbon cable.

You do NOT have to unplug the ribbon cable to complete this process, you
should just pull the keyboard back far enough to access the memory cover.

4. Carefully, using a small flat screwdriver, locate the (2) small tabs then push down
and pry up the keyboard at the two (2) points indicated in the figure below.

5. Lift the keyboard away from the computer chassis to expose the memory module
compartment door.

Memory

Module

Keyboard

Ribbon Cable

Cover

6. Using a screwdriver, remove the screw that holds the memory module
compartment door in place.

7. Grasp the door and pull the door off the memory module slots.

Memory Modules 69

Memory Module Precautions:

When removing the module, pull on the plastic portion of the connector slots
tabs only. Do not pull on the metal part of the tabs, this may damage the tabs.

8. Remove the installed module if necessary.

a. Pull the tabs on the connector slot outward slightly, until the edge of the

memory module pops up.

o

4

5

b. Hold the memory module by the edges and pull it forward out of the

compartment.

9. Align the connector on the memory module with the connector of the slot.

10. Push the memory module into the slot at a slight angle (~30

o

) until the connectors

are fully engaged.

11. Push down on the edge of the memory module until the module snaps into place.

12. Carefully align the memory module compartment door with the compartment,

13. Replace the keyboard by inserting the top at a ~ 30

14. Close the LCD and turn over the computer, then replace the screw you removed in

70 Users Manual

insuring that the tabs ate in properly then reinstall the screw you removed in step 6.

o

angle and carefully pushing

down at the bottom near the (2) tabs until it snaps into place.

step 2.

Video Features and Configuration

Resolution and Colour Depth

The resolution of the LCD is the sharpness of the image it can display. Resolution is
measured by the number of pixels (individual dots) displayed on the entire screen. In
general, the more pixels the LCD can display, the better the image.

The number of colours the LCD can display is measured by how many bits the LCD
uses to represent each pixel:

• 16-bit colour can support 64 K (65,536) colours.

• 32-bit colour can support 16 M (16.8 million) colours.

All these video modes can be displayed on an external monitor. However, if you
disconnect an external monitor that was attached to your computer and then start the
computer, the LCD may revert to a different resolution than the one you chose for the
external monitor.

Adjusting the LCD Brightness

There are 6 levels of LCD brightness (1: Dimmest ~ 6: Brightest). The default LCD
brightness setting is level 4. Whenever you change the power source, the brightness
level is changed to the following setting:

• When operating on AC power : Level 6 (Brightest)

• When operating on battery power : Level 1 (Dimmest)

Once the LCD brightness has been changed, the changed setting will be maintained
after restarting the computer. When the power source is changed (AC to battery or
battery to AC) while in operation, both the default brightness settings described above
will be restored.

You can adjust the LCD brightness by pressing <Fn+Up Arrow> or <Fn+Down
Arrow> on the keyboard.

Video Features and Configuration 71

Configuring Display Features

The following sections describe how to configure the display settings on your
computer.

Display Resolution Notes:

When Windows XP is initially installed it will automatically adjust the resolution
to maximum available.

Changing Colour Depth and Resolution

To change the colour depth and resolution of your LCD:

1. Click Start > Control Panel > Appearance and Themes.

2. Click icon. The Display Properties window appears.

3. Click the Settings tab. The Settings screen appears.

4. To change the colour depth, click the arrow next to the Colour quality palette and

select the available colour depth you want.

5. To change the resolution, click and drag the slider under the Screen resolution
until you select the available resolution you want.

6. Click OK.

72 Users Manual

Using External Display Devices

You can display on an external monitor or television instead of the LCD of your
notebook computer. You can duplicate the same screen on both the LCD and the
monitor simultaneously, but not the LCD and the television.

TV Connection Restrictions

You should only connect/disconnect cables and wires to your computer and
TV when the power is off.

TV Support Limitations

The computer will only support televisions with S-VHS output capability. The
standard composite video in port is not supported.

The TV-out port is not supported in DOS mode.

To start using an external display device

1. Connect the external monitor or the television to the monitor port or TV out port
of the computer.

2. Right-click on the desktop, and click Graphics Options > Output To. Click
Monitor, Television, or Intel(R) Dual Display Clone > Monitor + Notebook.

To use <Fn>+<F3> keys

Press <Fn>+<F3> to change the setting to display on the LCD, the monitor, or
simultaneously on the LCD and the monitor.

To use <Ctrl>+<Alt>+<F1/F2/F3> keys

Press <Ctrl>+<Alt>+<F1> to change the setting to display on the monitor.
Press <Ctrl>+<Alt>+<F2> to change the setting to display on the television.
Press <Ctrl>+<Alt>+<F3> to change the setting to display on the LCD.

To change setting for each display device
Right-click on the desktop, and click Graphics Options > Graphics
properties. On the Device tab, select a display device and change color
quality and screen resolution setting, then click OK.

Using External Display Devices 73

To stop using an external display device

1. Right-click on the desktop, and click Graphics Options > Output To >
Notebook.

2. Disconnect the external monitor or television from the computer.

74 Users Manual

Using Options

Authorised Reseller Options

You can order the following options for your Notebook computer from your authorised
reseller:

• An extra AC adapter

• An auto adapter that enables you to charge the computer’s battery and operate

the computer while in an automobile.

• An extra battery pack

• 128, 256 and 512 MB PC133 SDR SDRAM memory modules that enable you

to upgrade your computer’s memory to a maximum of 1 GB.

The options that are available may change periodically. Contact your reseller for
updated information on current and new options.

Factory Options

You may order these options at the time of purchase:

• A CD-ROM drive (Factory Option)

• A CD-R/W drive (Factory Option)

• DVD-ROM drive (Factory Option)

• CD-RW/DVD-ROM Combo drive (Factory Option)

• IEEE 1394 Port (Factory Option)

Using Options 75

Troubleshooting

Complete the following in the order presented until your system is functioning
properly. If all of the steps below fail then contact your local reseller for assistance.

 Questions and Answers

Please see “Questions and Answers” on page 77 for assistance in correcting any
computer operational problems.

 Check the Connections

Verify all of the power and peripheral cables are securely plugged into their sockets
and that your system and power supply is on.

 Norton AntiVirus

Run Norton AntiVirus to insure a virus is not affecting your computer. The Norton
Antivirus Subscription on your Samsung notebook will expire within 3 months. It is
your responsibility to update the virus definitions, and renew subscription with
Symantec when the subscription expires.

To run Norton AntiVirus proceed as follows:

Click Start > All Programs > Norton AntiVirus > Norton AntiVirus 2002.

 Windows Help and Support

Run Windows Help and Support to find problem that may be affecting your
computer.

To run Windows Help and Support proceed as follows:

Click Start > Help and Support.

 Reinstalling Software and Windows XP

If for some reason your system crashes, you may corrupt your HDD, Windows
Operating system and/or some of your device drivers. If this is the case, use System
Recovery CD to reinstall OS and System Software CD to reinstall the corrupt device
drivers.

76 Users Manual

System Recovery Precaution:

Before you start restoring your windows operating system insure you backup
all data on your hard drive.
Samsung is NOT responsible for any data loss.

Questions and Answers

The followings describe troubleshooting and reference information for the problems
that may occur during using your computer.

Windows Related

Q1 The system does not shutdown properly.

A When the system does not shutdown normally, press and hold the Power button

until the system manually shuts off. If the Power-Saving Mode is configured into
the Power button, press and hold for more than 4 seconds to shut the system off.
When the system is turned on after such manual shutdown, Scandisk will run to
check errors in the system.

Q2 The system freezes during program operation

A1 There is an error with the program currently being used. Press the <Ctrl>, <Alt>,

and <Delete> keys simultaneously and click and Task in the [Windows Task
Manager] window.

A2 There is an error with the Windows OS. Reboot the system by using the Power

button.

Q3 The USB mouse and touchpad do not work in the Safe mode on Windows 98.

A The touchpad may not operate in Windows 98 safe mode when the USB mouse

is installed. Use the touchpad or an external PS/2 mouse in Windows 98 safe
mode without installing USB mouse.

Q4 DOS window is displayed abnormally after applying a new desktop theme

on Windows 98.

A When you apply a new desktop theme, if you run a MS-DOS window and then

switch to full DOS screen mode, the screen may be displayed abnormally. If this
symptom occurs, press the <Fn>+<F4> keys to switch to standby mode. Then,
the screen will be displayed normally. If you use full DOS screen mode, we
recommend to revert the desktop theme to the default theme of Windows. (To
revert to the default theme, click Start > Settings > Control Panel> Desktop
theme> Windows default.)
Please be careful not to use the full DOS screen mode when a custom desktop
theme is used.

Troubleshooting 77

DOS Mode Related

Q1 DOS prompt is not displayed normally in full DOS screen mode.

A When graphic setting is set to notebook and the "Full Screen" option is set, this

problem may occur if you switch between full DOS screen mode and DOS
window mode. To resolve the problem, right-click on the desktop, and click
Graphic Options > Graphic Settings, then clear the "Full Screen" check box. Or,
click Graphics icon on the Windows taskbar and click Graphic Options, and then
set the Monitor Alignment item to "Disable". We also recommend not to switch
repeatedly between full DOS screen mode and DOS window mode.

To release the full screen mode with a shortcut key

Press the <Ctrl> + <Alt> + <F11> keys to release full screen. First, release full
screen mode on Windows and then switch to full DOS screen to ensure that
the screen is displayed normally.

Q2 When I connected a TV in DOS mode and start the computer, the screen is

not displayed.

A DOS mode does not support TV output. Start your computer in LCD mode and

then connect the TV in Windows mode.

78 Users Manual

Display Problems

Q1 LCD screen is dim.

A1 Adjust LCD screen brightness. Use the <Fn> + <Up Arrow> or <Fn> + <Down

Arrow> keys on the keyboard.

A2 Each time you press the <Fn>+<F3 / LCD/CRT>, the screen is displayed in the

order of Notebook>Monitor>Notebook+Monitor. Press those keys and check
whether the screen is displayed properly.

Q2 I removed the graphic driver on Control Panel and the screen is not

displayed.

A Start your computer in safe mode and then restart your computer. The screen will

be displayed.

In case of using an external display device (monitor), connect it to your notebook
and then configure the settings so that you can view the screen on both of your
notebook and monitor at the same time (called Dual Display mode). Then remove
the graphic driver on Control Panel. Now, you can view the screen on the monitor
connected.

Q3 The notebook screen is smaller than the LCD size in dual display mode.

A This problem may occur when the screen resolution is set to a smaller resolution

than 1024×768. This occurs because the Intel graphics chipset used in the
product does not support extending to full screen when the screen resolution is
set to 640×480 or 800×600 in dual display mode. Hence, you should release the
dual display mode to view full screen fitted to the LCD size.

Right-click on the desktop, and click Graphic Options > Graphic Settings. Then
select Notebook on the Device tab and select the "Full Screen" check box.

Or, click Graphics icon on the Windows taskbar and click Graphic Options, and
then set the Monitor Alignment item to "Enable".

To set/release the full screen mode with a shortcut key

Press the <Ctrl> + <Alt> + <F11> keys to set/release full screen.

Q4 The screen blinks or the pointer disappears when the <Fn>+<F3 / CRT/

LCD> keys are pressed.

Troubleshooting 79

A This problem occurs when you try to switch display device by pressing the

<Fn>+<F3 / LCD/CRT> keys when no monitor is connected. Connect a monitor
before switching display device.

Q5 Display screen is abnormal. (Afterimage, white spots, blinking, etc)

A These problem may occur during detecting display devices when your computer

starts, or awakes from standby or hibernation mode, or when you press the
<Fn>+<F3 / LCD/CRT> keys, or change the screen resolution.

In case of afterimages, the screen will be displayed normally after a while. Please
be careful that those symptoms may occur when you change modes (such as
display screen mode) while a 3D game or program is being executed. If abnormal
symptom persists, try to restart your notebook.

80 Users Manual

Modem Related

Q1 I cannot hear the modem sound.

A1 Check that the telephone line is properly connected to the modem.

A2 Check that the modem driver is installed properly.

1. Click Start > Control Panel > Performance and Maintenance > System.

2. Select Hardware tab > Device Manager > Modems in the System Properties

window, and check if there is a yellow exclamation mark on the installed modem
icon. If there is, delete the modem device driver and reinstall the driver, because
the yellow exclamation mark represents a not properly installed driver.

3. If there is no yellow exclamation mark, double-click the installed modem, and

click Diagnostics tab > Query Modem in the Modem Properties window to
diagnose the modem.

No message in either of Command and Response in the Diagnostics tab means
that the modem is not operating properly.

Diagnose the modem again after restarting the system or reinstalling the driver.

(You have to exit all programs using modem in the advance of diagnostics of the
modem).

A3 Although I can make a connection with the modem, I cannot hear the dial tone

and modem connection sound. In this case check the following list:

1. Click Start > All Programs > Accessories > Entertainment > Volume Control.

2. Clear the Mute check box in the Telephone Line item.

(Depending on the sound driver, it may be displayed as another name such as
Modem, Phone, Mono. If there is no corresponding item, click Options >
Properties > Volume Control, select 'Playback', and select the 'Telephone Line'
under the 'Display the following volume controls'. Click OK.)

Q2 I cannot make a call using an extension line.

A In general, the dial tone of a PBX or a digital phone switching system is not a

continuous one, unlike that of trunk line.

Therefore, the modem may not make a call because the modem mistakes the dial
tone from a PBX or a digital phone switching system as a busy tone.

In this case, complete the following procedures.

Troubleshooting 81

- Using an AT command

As an initialization command, use the command, ATX3.

Otherwise, enter the ATX3 command manually before making a call.

It can correct this problem by skipping the dial tone check step.

- Configuring the Modem through the Control Panel

1. Click Start > Control Panel > Network and Internet Connections.

2. Under See Also, click Phone and Modem Options.

3. In the Modems tab, select the installed modem, and click Properties.

4. In the Modem tab of the Modem Properties window, clear the 'Wait for dial tone

before dialing' check box.

5. When the configuration is completed, click OK.

Q3 How do I use my modem when dialing from overseas?

A1 Check that the modem is correctly configured according to the current country.

Because the values for communication may differ according to the country, you
may not be able to connect via the modem due to an incorrect modem
configuration.

1. Click Start > Control Panel > Network and Internet Connections.

2. Under See Also, click Phone and Modem Options.

3. In the Dialing Rules tab, click Edit.

4. In the General tab in the Edit Location window, select the current country from

the Country/region radio box, specify the Area code, and click OK.

A2 Because the shape of the telephone plug may differ according to the country, you

Q4 How do I receive a fax while the system is in power saving mode (Rest mode)

A To receive a fax when the system is in power saving mode, and the operating

1. The automatic fax reception function of the fax program needs to be activated.

2. Click Start > Control Panel > Network and Internet Connections.

3. Under See Also, click Phone and Modem Options.

82 Users Manual

have to purchase and use the appropriate telephone plug for that particular
country.

(For Windows XP and 2000)?

system is Windows XP or 2000, configure the system as follows:

(For more information, refer to the corresponding fax program manual.)

4. In the Modems tab, select the installed modem, and click Properties.

5. In the Power Management tab of the Modem Properties window, select the "This

device activates the computer in power saving mode" check box, and click OK.

The above setting enables the modem to turn on the system and receive a fax

when in power saving mode.

Troubleshooting 83

Wireless LAN Related

Q1 The Wireless LAN device is operating properly, but I cannot connect to the

network.

This is due to an incorrect configuration, or a configuration error. Check the
following check lists:

A1 If you are using a computer-to-computer network (peer-to-peer) connection,

check that the name of the configured network is correct. The network name used
to connect should be the same in all computers. The network name is case
sensitive, if the name contains letters.

A2 If you are using a network key (encryption key), an AP (Access Point) and a

computer-to-computer network (peer-to-peer), you have to use the same network
key. The network key of the AP is configured in the AP management program.
Ask your network administrator for more detailed information.

A3 Check that the device driver is properly installed. If the driver is not properly

installed, you will find a yellow exclamation mark on the network icon by
clicking Start > Control Panel > Performance and Maintenance > System >
Hardware tab > Device Manager > Network adapters > Wireless LAN adapter. If
there is a yellow exclamation mark, please reinstall the device driver with the
system software CD.

A4 To connect to an access point using network authentication (Shared key):

- In Windows XP, select Network Authentication (Shared mode) in the Wireless
Network Properties window.

- If you use the wireless LAN program (PROSet) in Windows 2000, make sure
that the network authentication mode is configure to Shared in security settings.
For more information on the network authentication configuration procedures,
ask your access point administrator.

Q2 The signal strength is excellent, but I cannot connect to the network.

A1 Check that the TCP/IP properties are configured properly. When you connect to

84 Users Manual

Even if the signal strength is excellent, the network connection may not operate
properly if the TCP/IP properties are not properly configured, or the network key
(encryption key) is incorrect.

an AP, click the Wireless Network Connection icon on the taskbar and select the
Support tab. If the IP is not allocated properly, the IP address will be displayed
as follows. (e.g. 169.254.xxx.xxx)
If the network does not provide DHCP, you have to specify the correct IP address
by asking your network administrator.

Even if the network provides DHCP, the server may not allocate an IP address to
the client properly, and the client station cannot connect to the network.

A2 If you are using a network key (encryption key), an AP (Access Point) and a

computer-to-computer network (peer-to-peer), you have to use the same network
key. The network key of the AP is configured in the AP management program.
Ask your network administrator for more detailed information.

Q3 I cannot share an Internet connection.

A1 It may require some time to synchronize the computers to share an Internet

connection after the Internet connection sharing configuration is completed. If
you cannot share Internet connection even after a longer period, restart the
computer.

A2 Check if there is a configured bridge connection between the network adapters.

If there is a configured bridge connection between the network adapters through
the network configuration wizard, remove the network bridge, and reconfigure
the Internet connection sharing.

Q4 I cannot connect to the AP wireless network.

A1 Check the wireless LAN radio environment. Using a wireless LAN may be

restricted by the surrounding radio environment, and the distance between
wireless stations. Also obstacles such as walls or doors may affect wireless LAN
connections.

A2 Check that the AP is operating properly. Turn the AP off, and turn it on after a

short wait.

A3 Check that the network key (encryption key) configuration for the AP is correct.

Q5 In the Windows XP 'Available wireless networks' window, the Wireless

Network Connection is displayed as 'Not Available'.

A1 Check that the specific program for a wireless LAN connection is installed.

Windows XP supports wireless LAN connections through the Wireless Zero
Configuration (WZC) service. Therefore, an additional program for a wireless
LAN connection is not required. However, installation of the specific program
for a wireless LAN connection may disable the 'Available wireless networks'
window of the Wireless Network Connection supported by WZC service in
certain cases. Exit the program and try again.

A2 Initialize the device driver.

Click Start > Control Panel > Performance and Maintenance > System >

Troubleshooting 85

Hardware tab > Device Manager > Network adapters, and select the wireless
LAN adapter. Right-click the network adaptor and select 'Disable'. Then right­click over the network adaptor and select 'Enable' after a short wait to check that
the device is operating properly.

Q6 The Wireless network connection operates properly, but the Wireless

Network Connection icon on the taskbar displays the "Disconnected"
message.

A This is one of the known problems when you are using a wireless LAN

connection after installing Windows XP service pack 1.

Check that the wireless LAN card is operating properly by initializing the device
driver referring to A2 of Q5. For more information, refer to the following link for
known problems with Microsoft.
http://support.microsoft.com/default.aspx?scid=kb;en-us;Q328647

Q7 When connecting to a computer-to-computer (Ad Hoc) network, I cannot

connect to another computer connected to the same computer-to-computer
network.

A1 Make sure that the security settings and network name of the computer-to-

computer (Ad Hoc) network is correct.

A2 Check the TCP/IP properties of the computers to be connected through the

computer-to-computer (Ad Hoc) network. All of those computers should be
configured so that their IP addresses are within the same subnet range.

- If the IP address is configured to DHCP (Obtain an IP address automatically) in
TCP/IP properties, IP address is configured within the same subnet range
automatically.

- If the IP address is configured to static IP in TCP/IP properties, select Use the
following IP address in the TCP/IP properties of the wireless adapter, configure
IP address:10.0.0.1~10.0.0.254, and Subnet mask: 255.255.0.0, and then try
again.

Q8 My notebook does not awake from standby mode or hibernate mode when

A Click Start > Control Panel > Performance and Maintenance > System >

86 Users Manual

Orinoco USB Wireless LAN is used.

Hardware tab > Device Manager > Network Adapter > Orinoco USB Client.
Then check the properties of Orinoco USB Client.
Click Power Management on the Device property. Clear the "Can turn off this
device to conserve power." check box. Then your computer will work normally.

Games and Programs Problems

In Windows XP, when some application programs, especially games, are running,
some operating problems may occur because some specific functions are not supported
normally or device drivers are not compatible perfectly. For latest drivers and
troubleshooting information, please visit our web site.

Q1 LCD screen looks small when running a game.

A In dual display mode, full screen mode is not supported for LCD screen. If you

want to extend the screen in LCD only mode so that it fits to the LCD size, right­click on the desktop, and click Graphic Options > Graphic Settings. Then, select
Notebook on the Device tab and select the "Full Screen" check box. (Or, right­click on the desktop, and click Graphic Options, and then set the Monitor
Alignment item to 'Enable'.)

To set/release the full screen mode with a shortcut key

- Press the <Ctrl> + <Alt> + <F11> keys to set/release full screen.

- Do not switch to full screen mode when a 3D program is running. Otherwise,
the screen may be displayed abnormally in full screen mode.

Q2 Cannot run 3D games, or some functions do not work.

A Set the graphic setting for the game to '2D' or 'Software Renderer' and then try to

run it again.

Q3 A game does not run when it is executed immediately after installation.

A This problem occurs when the game is not compatible with Windows XP. Try to

run the game again and it will run normally.

Q4 My computer does not operate when I switch display device by pressing the

<Fn> + <F3 / LCD/CRT> keys during running a 3D program or VCD/
MPEG/DVD.

A Errors may occur when the <Fn> + <F3 / LCD/CRT> keys are pressed during

running a 3D program or VCD/MPEG/DVD. Be careful not to press the <Fn> +
<F3 / LCD/CRT> keys during running a 3D program or VCD/MPEG/DVD.

On Windows XP, the <FN> + <F3 / LCD/CRT> keys are disabled when
running VCD/MPEG/DVD in 1024x768 screen resolution.

Troubleshooting 87

Q5 Screen resolution changes or the screen is not displayed when playing back

music file (Mid/MP3/Wave) with Media player.

A This problem may occur when you try to switch display device by pressing the

<Fn>+<F3 / LCD/CRT> keys or the <Ctrl> +<Alt>+<F1 or F3> keys when
Media player is running in full screen mode. Be careful not to press the
<Fn>+<F3 / LCD/CRT> keys or the <Ctrl> +<Alt>+<F1 or F3> keys while
Media player is running.

Pressing the <Ctrl>+<Alt>+<F1> keys switches to monitor screen. Pressing
the <Ctrl>+<Alt>+<F3> keys switches to notebook LCD screen.

Q6 The screens break when Windows Movie Maker is running in full screen

mode.

A Change color quality to 16-bit, and the screen will be displayed normally.

Q7 Screen stopping occurs during playing back a video CD or audio CD from

the CD-ROM drive.

A Click Start > Control Panel > Performance and maintenance > System >

Hardware tab > Device Manger. Right-click on Secondary IDE channel under
IDE ATA/ATAPI Controller and click Properties. On the Advanced Settings tab,
check the transfer mode. If it is set to PIO only, change it to DMA (when
available).

Q8 The screen is abnormal when a moving picture game is running.

A This problem may occur when a moving picture is running in full screen mode.

Q9 The screen is displayed abnormally when an image is inserted into MS-

A The problem may occur during scrolling the screen when images are inserted into

88 Users Manual

Release the full screen mode on the Graphics settings window before running a
moving picture.

Office program file. (MS-Word, MS-Excel, etc)

MS-Office program file. Update the graphics driver with the drivers contained in
the Software CD and set color quality to '32-bit'. (Refer to ReadMe.htm on the
Software CD.)

Q10 The screen is displayed abnormally when the Metal of Honor game is

running.

A Set the texture detail to 'Low' on the Graphic settings of the game options. Or,

install the graphics driver using the Software CD.

Troubleshooting 89

Reinstalling Software

If you have reinstalled the Windows operating system, or the system and program do
not operate properly, you can reinstall the driver and program using the system
software CD.

The drivers and programs included in the system software CD are listed in the
D:\ReadMe.htm file. (Provided that the name of CD-ROM drive is "D".)

Running the system software CD

Insert the system software CD into the CD drive. The initial screen appears
automatically.

Installs device drivers

Installs programs

Installing drivers

1. In the initial screen, click Driver Installation.

2. Select the driver you want to install from the device installation screen, and click

90 Users Manual

Install Now!

How can one install the drivers for operating systems other than
Windows XP?

Install the appropriate driver software included in the system software CD.

Installing programs

1. In the initial screen, click Install programs.

2. Click Standard installation in the program installation screen (standard

installation is recommended).

• Standard installation: Installs and recovers programs to the state of shipment.

• User installation: You can select the program installation location, and other

options for the program installation.

Troubleshooting 91

Reinstalling Windows XP

If the Windows XP does not operate properly due to an error in the system, or if you
have replaced the hard disk drive, you can reinstall Windows XP using the system
recovery CD.

With the system recovery CD, you can reinstall Windows XP only. To return
the system to the state of shipment, reinstall the device drivers and programs
with the system software CD after reinstalling Windows XP with the system
recovery CD.

Reinstalling Window may delete the data on the hard disk drive such as files,
programs, etc. In order to minimize damage from data loss, please remember
to always back up data. Samsung Electronics is not liable in the case of data
loss, please consult your warranty statement for clarification.

Reinstalling Windows

1. Insert the system recovery CD into the CD-ROM drive.

2. In the initial screen, click Standard installation. (Installation with the standard

installation option is recommended. The standard installation does not require
steps 5 and 7.)

92 Users Manual

• Standard installation: Installs Windows preserving the data saved on the hard

disk drive. However, since personal data that is in the Windows folder may be
deleted, please backup personal data.

• Custom installation: Enables Windows installation after partitioning or

formatting the hard disk drive. Note that all data on the hard disk drives may be
deleted depending on your configuration.