Samsung NT10FK02CX, NT10FP02CX, NT10FP03DR, NT10FK03DR, NT10FP01WX User Manual

Notices

No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, mechanical photocopying, recording or
otherwise, without the prior written permission of the manufacturer.

The information within this manual is subject to change without notice.

The manufacturer shall not be held liable for technical or editorial errors or omissions
contained in herein; nor for incidental or consequential damages resulting from the

furnishing, performance or use of this material.

Microsoft Windows is a registered trademark of the Microsoft Corporation.

Product names mentioned herein are for identification purposes only, and may be
trademarks and/or registered trademarks of their respective companies.

Macrovision Statement

If your computer has a DVD drive and an analog TV Out port, the following
paragraph applies:

This product incorporates copyright protection technology that is protected by method
claims of certain U.S. patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.

Copyright 2002 All rights are reserved

Notices i

Important Safety Information

Safety Instructions

Your system is designed and tested to meet the latest standards for safety of
information technology equipment. However, to ensure safe use of this product, it is
important that the safety instructions marked on the product and in the documentation
are followed.

Always follow these instructions to help guard against personal injury and
damage to your system.

i

Setting Up your System

• Read and follow all instructions marked on the product and in the

documentation before you operate your system. Retain all safety and operating
instructions for future use.

• Do not use this product near water or a heat source such as a radiator.

• Set up the system on a stable work surface.

• The product should be operated only with the type of power source indicated on

the rating label.

• Ensure that the electrical outlet you are using to power your equipment is easily

accessible in case of fire or short circuit.

• If your computer has a voltage selector switch, make sure that the switch is in

the proper position for your area.

• Openings in the computer case are provided for ventilation. Do not block or

cover these openings. Make sure you provide adequate space, at least 6 inches
(15 cm), around the system for ventilation when you set up your work area.
Never insert objects of any kind into the computer ventilation openings.

• Ensure that the fan vents on the bottom of the casing are clear at all times. Do

not place the computer on a soft surface, doing so will block the bottom vents.

• If you use an extension cord with this system, make sure that the total ampere

rating on the products plugged into the extension cord does not exceed the
extension cord ampere rating.

ii Users Manual

Care During Use

• Do not walk on the power cord or allow anything to rest on it.

• Do not spill anything on the system. The best way to avoid spills is to not eat or

drink near your system.

• Some products have a replaceable CMOS battery on the system board. There is

a danger of explosion if the CMOS battery is replaced incorrectly. Replace the
battery with the same or equivalent type recommended by the manufacturer.
Dispose of batteries according to the manufacturer’s instructions. If the CMOS
battery requires replacement insure that a qualified technician performs the task

• When the computer is turned off, a small amount of electrical current still flows

through the computer. To avoid electrical shock, always unplug all power
cables, remove the battery and modem cables from the wall outlets before
cleaning the system.

• Unplug the system from the wall outlet and refer servicing to qualified

personnel if:

– The power cord or plug is damaged.

– Liquid has been spilled into the system.

– The system does not operate properly when the operating instructions are

followed.

– The system was dropped or the casing is damaged.

– The system performance changes.

Replacement Parts and Accessories

Use only replacement parts and accessories recommended by manufacturer.

To reduce the risk of fire, use only No. 26 AWG or larger telecommunications

line cord.

Do not use this product in areas classified as hazardous. Such areas include

patient care areas of medical and dental facilities, oxygen rich environments,

or industrial areas.

Important Safety Information iii

Battery Disposal

Do not put rechargeable batteries or products powered by non-removable
rechargeable batteries in the garbage.

Contact the Samsung Helpline for information on how to dispose of batteries that you
cannot use or recharge any longer.

Follow all local regulations when disposing of old batteries.

iv Users Manual

Federal Communications Commission (FCC)

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class
B digital device pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates and can radiate radio
frequency energy and if not installed and used in accordance with the
instructions may cause harmful interference.. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

If necessary, the user should consult the dealer or an experienced radio/television
technician for additional suggestions. The user may find the following booklet helpful:
"Something About Interference." This is available at FCC local regional offices. Our
company is not responsible for any radio or television interference caused by
unauthorized modifications of this equipment or the substitution or attachment of
connecting cables and equipment other than those specified by our company. The
correction will be the responsibility of the user. Use only shielded data cables with this
system.

FCC statement for Wireless LAN use:

"While installing and operating this transmitter and antenna combination the
radio frequency exposure limit of 1mW/cm2 may be exceeded at distances
close to the antenna installed. Therefore, the user must maintain a minimum
distance of 20cm from the antenna at all times. This device can not be
colocated with another transmitter and transmitting antenna."

Federal Communications Commission (FCC) v

Federal Communications Commission Part 68 Statement

This equipment compiles with part of the FCC rules. On the back of this equipment is
a label that contains, among other information, the FCC registration number and ringer
equivalence number(REN) for this equipment. If requested, this information must be
provided to the telephone company.

This equipment uses the following USOC jacks : RJ11C

An FCC compliant telephone cord and modular plug is provided with this equipment.
This equipment is designed to be connected to the telephone network or promises
wiring using a compatible modular jack which is Part 68 compliant. See Installation
Instructions for details.

The REN is used to determine the quantity of devices which may be connected to
telephone line. Excessive RENs on the telephone line may result in the devices not
ringing in response to an incoming call. In most, but not all areas, the sum of RENs
should not exceed five(5.0). To be certain of the number of devices that may be
connected to a line, as determined by total RENs, contact the local telephone company
to determine the maximum REN for the calling area.

If the terminal equipment causes harm to the telephone network, the Telephone
Company will notify you in advance that temporary discontinuance of service may be
required. But if advance notice is not practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of your right to file a complaint
with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations, or
procedures that could affect the operation of the equipment. If this happens, the
telephone company will provide advanced notice in order for you to make necessary
modifications to maintain uninterrupted service.

If trouble is experienced with this equipment (SENS Modem) for repair or warranty
information, please contact your local distributor. If the equipment is causing harm to
the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.

The user must use the accessories and cables supplied by the manufacturer to get
optimum performance from the product.

No repairs may be done by the customer.

This equipment cannot be used on public coin phone service provided by the telephone
company. Connection to party line service is subject to state tariffs.

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to
use a computer or other electronic device, including faxmachines, to send any message
unless such message clearly contains in a margin at the top or bottom of each

vi Users Manual

transmitted page or on the first page of the transmission, the date and time it is sent and
an identification of the business or other entity, or other individual sending themessage
and the telephone number of the sending machine or such business, other entity, or
individual. (The telephone number provided may not be any number for which charges
exceed local or long-distance transmission charges.)

In order to program this information into your fax machine, refer to your
communications software user manual.

CTR21 Statement

The equipment has been approved in accordance with Council Decision 98/482/EC for
pan-European single terminal connection to the public switched telephone network
(PSTN). However, due to differences between the individual PSTNs provided in
different countries, the approval does not, of itself, give an unconditional assurance of
successful operation on every PSTN network termination point.

In the event of problems, you should contact your equipment supplier in the first
instance.

Canadian Radio Interference Regulations

This apparatus does not exceed the class B limits for radio noise emissions set out in
the radio interference regulations of the Canadian Department of Communications.

Le présent appareil n’émet pas de bruits radioélectriques dépassant les limites
applicable aux appareils de la classe B prescrites par le règlement de brouillage
radioélectrique dicté par le Ministère des Communications du Canada.

Federal Communications Commission (FCC) vii

Laser Safety

All systems equipped with CD or DVD drives comply with the appropriate safety
standards, including IEC 825. The laser devices in these components are classified as
“Class 1 Laser Products” under a US Department of Health and Human Services
(DHHS) Radiation Performance Standard. Should the unit ever need servicing, contact
an authorized service location.

Laser Safety Note:

Use of controls or adjustments or performance of procedures other than those
specified in this manual may result in hazardous radiation exposure. To
prevent exposure to laser beams, do not try to open the enclosure of a CD or
DVD drive.

viii Users Manual

Power Cord Requirements

The power cord set (wall plug, cable and AC adapter plug) you received with your
computer meets the requirements for use in the country where you purchased your
equipment.

Power cord sets for use in other countries must meet the requirements of the country
where you use the computer. For more information on power cord set requirements,
contact your authorized dealer, reseller, or service provider.

General Requirements

The requirements listed below are applicable to all countries:

• The length of the power cord set must be at least 6.00 feet (1.8m) and a

maximum of 9.75 feet (3.0m).

• All power cord sets must be approved by an acceptable accredited agency

responsible for evaluation in the country where the power cord set will be used.

• The power cord set must have a minimum current capacity of 7 A and a

nominal voltage rating of 125 or 250 volts AC, as required by each country’s
power system.

• The appliance coupler must meet the mechanical configuration of an EN 60

320/IEC 320 Standard Sheet C13 connector, for mating with appliance inlet on
the computer.

Power Cord Requirements ix

Country-Specific Power Cord Set Requirements

The requirements listed below are applicable to the specific country listed:

Country

Australia EANSW 1

Austria OVE 1

Belgium CEBC 1

Canada CSA 2

Denmark DEMKO 1

Finland FIMKO 1

France UTE 1

Germany VDE 1

Italy

Japan JIS 3

The Netherlands KEMA 1

Norway NEMKO 1

Sweden SEMKO 1

Switzerland SEV 1

United Kingdom BSI 1

United States

Accrediting
Agency

IMQ 1

UL 2

Applicable Note
Numbers

Notes:

1. Flexible cord must be Type HO5VV-F, 2-conductor, 1.0 mm² conductor

size. Power cord set fittings (appliance coupler and wall plug) must bear
the certification mark of the agency responsible for evaluation in the
country where it will be used.

2. Flexible cord must be Type SVT or equivalent, No.18 AWG. Wall plug must
be a two-pole grounding type.

3. Appliance coupler, flexible cord, and wall plug must bear a "T" mark and
registration number in accordance with the Japanese Dentori Law. Flexible
cord must be Type VCT or VCTF, 2-conductor, 0.75 mm² conductor size.
Wall plug must be a two-pole grounding type with a Japanese Industrial
Standard C8303 (15 A, 125V) configuration.

x Users Manual

Using Your Documentation

Congratulations on your purchase of a notebook computer with the Windows® XP
operating system. Whether you are new to using a portable computer or are an
experienced user, this user’s manual can help you get the most from your computer.

Manual Documentation Conventions

Information Icons

Three icons and their associated messages appear in this manual. The information
icons are placed before the step/information they apply to:

Warning:

Indicates the possibility of personal injury.

Caution:

Warns you of possible damage to equipment or data.

Note:

Informs you of special circumstances.

Technical Information:

Informs you of special requirements or limitations for use of item(s).

Keyboard Conventions

Keys that you need to press to perform certain functions are displayed in the manual
using a small graphic of the button. For example: <Ctrl>

or <Ctrl> indicates the control key (Ctrl on the keyboard).

If you need to press two keys at the same time, the key names are shown joined by a
plus sign. For example:

+

means that you should press the Fn key and hold it and then press the F8 key.

or <Fn+F8>

Using Your Documentation 1

CD-ROM Device Naming Convention

In many installation programs you will have to get a program from the CD-ROM
device. The program installation sequence assumes that the CD is drive d:\, however
this is not always the case. The name of the CD-ROM drive is the letter following the
letter assigned to your last HDD. For instance, if you have one HDD with two
partitions, the HDD is drives C: and D: and the CD-ROM drive is then drive E.

Touchpad Conventions

You may be asked to click or double-click on items on the display screen. As a general
note the touchpad actions act much in the same way as a wheel mouse, any differences
are explained fully.

The object that needs to be clicked upon will be displayed in Bold text or shown in a
small figure such as the “Start Button” shown on the right =>.

Table 1. Touchpad Click Conventions

Action Process

Click Depress the touchpad left button and release

Double-Click Quickly click the left touchpad button two times

Windows Conventions:

Almost all “Windows” programs will display the name/function of a button or
icon if you place the touchpad pointer on the item you want information about.

Software User Documentation

Your computer is shipped from the factory with several software programs installed.
The software may include its own online or printed documentation. Refer to the
documentation or the Help options in the software for more information.

The figures and illustrations in this manual may not be identical to those on
your system.

General Icon Note:

Some of the Icons used in Windows XP may be placed on the taskbar by
selecting (ex: Place the volume icon in the taskbar) in the properties dialog
box.

2 Users Manual

Introducing Your Computer

Your computer is a lightweight portable computer that includes features such as Dolby
Digital & Dolby Theater System support, CD-ROM/floppy drives, Biometric
(fingerprint) security system (factory option) and wireless LAN capability (factory
option), to meet your computing needs at home or on the road. [Figures may be
different depending on options).

Where Everything Is

The next 6 figures will explain the location of all of the buttons, LEDs and equipment
needed to operate your notebook computer.

Front

LCD Latch

Biometric

Security

pad

Speaker

Power Button

Keyboard

SENS Keyboard

LEDs

Power, Battery Status

& E-mail LEDs

Buttons

Touchpad
Touchpad Buttons
Internal Microphone

Speaker

Introducing Your Computer 3

Buttons and LEDs

Power Button

Number Lock Icon

Caps Lock Icon

Scroll Lock Icon

Drive Access Icon

Right Side

FDD Fan Vent LAN PortCD/DVD - ROM Hard Drive

Left Side

E-Mail Button

Internet Button

User
Programmable
Button

Battery Status

Power

E-Mail Alert

4 Users Manual

TV-Out Port

PC Card Eject Buttons PC Card Slot

Fan Vent

Security Lock Port

Battery

Wheel Volume
Control

SPDIF In Jack

Line In Jack

Microphone Jack

Headphone Jack

Back Side

PS/2 Port

Modem Port

DC-In Port

Bottom

Battery Compartment

Memory

Compartment

Parallel

Printer Port

Docking

Connector

External Monitor Port

Flex Bay Latch

Flex Bay Compartment

Hard Drive

Mini PCI

Compartment

1394 Port

USB Ports

Fan Vent

Introducing Your Computer 5

Using Your Computer for the First Time

This section gives you detailed information on using your computer for the first time.

Installing the Battery

To install the battery pack:

1. With the computer’s power off, close the LCD panel and turn the computer over

so the bottom of the unit faces up.

2. Slide the battery compartment cover straight up and off the computer.

Insert the battery into the battery compartment, ensuring the correct
orientation so that the battery fits in its slot properly.

3. Slide the battery pack into the compartment. Make sure the battery is fully inserted
into the compartment.

4. Align the tabs on the battery compartment cover with the slots on the battery
compartment.

5. Push the cover straight down until it snaps into place.

6 Users Manual

Attaching the AC Adapter

Your computer runs on power from the battery in the computer or from an electrical
outlet. The first time that you use your computer, fully charge the battery by attaching
the power cord to the computer and to an electrical outlet.

All batteries lose their charge if they sit unused for an extended time period.
When not used, battery can discharge fully in 2 to 3 months. The battery may
have discharged in the time it took for the computer to go from the factory to
you.

To attach the power cord:

1. Plug the AC adapter into the power connector on the back side of the computer.

2. Connect the power cord to the AC adapter and then to an electrical outlet.

AC Adapter

The battery starts charging as soon as you plug the power cord into an electrical outlet.
The battery charges faster if the computer is turned off during charging.

If the battery is fully depleted and the computer is turned off, the battery charges in
about 3 hours. If the computer is turned on, the battery charges in about 6 hours. When
the battery is charging, the battery charge light is red. When the battery is fully charged,
the light turns green.

See ”Using Power Management Options” on page 48 for more information on using
your computer’s battery.

Using Your Computer for the First Time 7

Turning On the Computer

To turn on the computer’s power for the first time:

1. Slide the LCD latch, located on the front of the cover to the right.

2. Lift up the cover.

3. Press and then release the power button.

The power light is on when the computer’s power is on.

Power button

Cover Latch

Initial Computer Startup:

The first time you start your computer you will see the operating system
registration screens. Simply read each screen and follow the simple directions.
You must complete this process in order to use your computer. A tutorial is
provided if you require it.

Adjusting the LCD Display

You may wish to adjust the LCD (Liquid-Crystal Display) when you begin using your
computer. A TFT (Thin-Film Transistor) LCD does not require adjustment for contrast
because the contrast is set to remain at maximum.

To adjust the LCD:

• Press <Fn+Right Arrow> to increase the display brightness.

• Press <Fn+Left Arrow> to decrease the display brightness.

8 Users Manual

+

+

Power Light

Turning Off Your Computer

Prior to shutting down your computer ensure all of your data and current work are
saved. The system will ask if you wish to save any unsaved work, saving your work
first will speed the shutdown process.

To turn off the computer, complete the following steps:

1. Click on the taskbar.

If you need to restart your computer after software (re)installation or because it is not
responding select the Restart option in step 3 below.

2. Click Shut Down Computer to display the shutdown popup window shown
below.

3. Click Turn Off to complete the shutdown sequence.

Power Off:

If the system does not power off, then press and hold the power button for over
5 seconds. See ”Using Power Management Options” on page 48.

Power Button Functions:

The power button has several functions other than just turning on and off your
computer, see “Using Power Management Options” on page 48.

You can also perform a soft boot by saving your files and pressing

+ +

<Ctrl+Alt+Del> to pop-up the “Windows Task Manager” window.

Click Shut Down > Restart.

You can perform a cold boot by pressing the power button for more than 4 seconds to
turn the computer off, waiting more than five seconds, and then pressing the power
button to turn the computer on. The system may perform some extra checks during the
restart.

Using Your Computer for the First Time 9

Tips for Using Your Computer

The following information helps you avoid potential problems as you use your
computer:

Do not try to disassemble your computer. Opening the system chassis voids
your warranty. Only an authorised manufacturer service center can replace or
add any parts inside the chassis.

• Follow all the instructions and cautions in your computer user documentation.

• The LCD has a polarized surface and can be damaged easily. To prevent

damage, avoid touching the screen.

• Use only approved AC adapters, auto adapters, memory modules and other

options.

• Because a notebook computer is small and has restricted air flow around

components, it is more likely to overheat than a desktop computer. A fan inside
your computer runs when needed to help eliminate heat. Make sure the fan vent
on the left side of your computer is not blocked when you use the computer.
Occasionally check the vents and remove any accumulated dust on the outside.

• Avoid using or storing the computer in extremely hot or cold areas, such as a

car on a hot day. Keep the computer away from heaters and out of direct
sunlight. Exposure to excessive heat may damage computer components. If you
have left your computer in a hot place, let it cool down slowly to room
temperature (with the LCD panel open) before using it.

• Do not remove the memory-module compartment door, or try to install a

memory module when the computer is on. (For information on installing
memory modules, see “Installing a Memory Module” on page 60.)

• Set up your computer work area to avoid physical strain. Sit with your back

straight and supported by your chair. Adjust your chair or work table so that
your arms and wrists can remain in a relaxed position, parallel with the floor.
Avoid bending or twisting your wrists as you work. Your hands should “float”
slightly above the keyboard. Refer to a book on office ergonomics for more
information on setting up your work area.

• Take frequent breaks from working at the computer to rest your eyes and

stretch your muscles.

• Remember to save your data files frequently and to make backup copies of your

files.

10 Users Manual

Travelling with Your Computer

Air Travel

If you are travelling by air, follow these tips:

• Take the computer with you as carry-on luggage. Do not check the computer

with your baggage.

• Allow the computer and disks to go through the X-ray security devices. Do not

hand-carry disks through the walk-through metal detectors, which can cause
loss of data.

• Make sure that the battery is charged or the power cord is easily accessible.

You may be required to turn on the computer for airport security personnel.

• Be prepared to turn off the computer during take off and landing.

Locking your Computer

As a precaution when you are travelling or using your computer in an unsecured area,
you should keep your computer as safe as possible. An option to do this is the Security
Lock System. Follow the Security Lock System manufacturers instructions for specific
installation and use. The following figure shows generally how to use the lock.

To Lock

From Lock

Using Your Computer for the First Time 11

Handling Spills

Do not spill anything on your computer. The best way to avoid spills is to avoid eating
and drinking around your computer. If you do spill something on your computer, turn
off your computer, unplug it immediately, and do the following:

• If you spill liquid on the keyboard, drain as much of the liquid from the

keyboard as possible. Be careful not to let the liquid drip onto the LCD panel.
Allow the system to dry for several days before trying to use it.

• If you spill liquid on an external keyboard or keypad, unplug it and drain as

much of the liquid as possible. Allow the keyboard to sit at room temperature
for a full day before trying to use it.

Sweet liquids leave a sticky residue that may jam the keyboard despite your
efforts to dry it.

• If you spill liquid on the LCD panel, clean it immediately with a soft cloth and

denatured alcohol or a proprietary LCD screen cleaner. Do not use water,
window cleaner, acetone, aromatic solvent, or dry, rough towels to clean it.

Some liquids damage the polarized LCD screen. If your screen is damaged,
contact your authorized manufacturer’s service center for a replacement.

Storing the Computer for Long Periods

If possible, leave the power cord connected to the computer and an electrical outlet
when the computer is not in use. This extends the life of the battery and keeps the
battery fully charged.

If you will not be using the computer for a long period of time (a month or more), you
should charge the battery until it is completely full. After you have done so, remove the
battery from the unit.

12 Users Manual

Using the Keyboard

Your computer has an 87/88-key keyboard. By pressing designated key combinations,
you can have access to all the key functions of a full-sized keyboard.

Function & Special Purpose Keys

Gauge

Gauge

Application Key

Although the layout of the keys on your computer’s keyboard is different from
that on a desktop computer’s keyboard, the keyboard feels like a full-sized
keyboard when you use it.

Windows KeyFunction Key

Embedded
Numeric Keypad

Cursor/Screen

Control Keys

The keys on the keyboard can be grouped into the following categories:

• Full-sized Alphanumeric typewriter keys are arranged like a standard

typewriter keyboard and are used for text entry. The Windows keys on either
side of the spacebar open Windows menus and perform other special functions.

• Function keys, when pressed together with the key, enable special

functions.

• Cursor and Screen control keys move the cursor. They may perform other

functions, depending on your software.

To clean the computer keyboard, use slightly damp cotton swabs. Scrub the keys and
the surface around the keys.

Using the Keyboard 13

Do not allow liquid to drip into the keyboard or you may damage the keyboard.

Using the Numeric Keypad

Your keyboard includes a numeric keypad, which is a group of keys that you can set to
type numbers and mathematical symbols, such as the plus sign. A number or symbol
on the right corner of each keypad key shows its numeric function.

Num Lock LED

Press to turn on the embedded numeric keypad. The numeric functions of the
keypad are enabled and the Num Lock LED turns on. (See ”Reading the System Status
Lights” on page 20 for the location of the Num Lock LED.)

While the numeric functions are enabled, you can temporarily return a key to its normal
function by pressing and the key. For example to type the letter m, press + ,
this operation displays the letter m.

To turn the numeric keypad off, press again. The Num Lock LED turns off.

14 Users Manual

Using Special Function Keys

The function key activates special functions when it is pressed in combination with
another keys. Table 2 shows the special key combinations.

Table 2. Description of Special Function Key Combinations

Key

Combinations

+

+

+

Gauge

+

+

+

+

+

+

+

+

Key
Name

F1
Prt Sc

F2
Sys Rq

F5
CRT/LCD

F6
Gauge

F8
Mute

F9

Volume
down:

F10

Volume
up:

F11
Rest:

F12
Scroll

Left
Arrow

Right
Arrow

Key Function

Print screen: Takes a picture of the open screen, which you can paste into

System
request:

CRT/LCD: Switches the display between the LCD, the external monitor,

Gauge Displays the battery gauge in the upper-right corner of your

Mute: Increases the audio volume.

Volume
down:

Volume up: Increases the audio volume.

Rest: Puts the computer into Suspend mode. To resume normal

Scroll: In some applications, sets the cursor-control keys to scroll

Brightness
Down:

Brightness
Up:

many graphics programs.

Reserved for use in software programs.

and simultaneous display on both the LCD and the external
monitor.

screen.
The gauge closes in a few seconds, or you can press <Esc>
to close the gauge. (See ”Monitoring the Battery Charge” on
page 39 for more information on the battery gauge.)

Decreases the audio volume.

operation from rest, press the power button. (See ”Using
Power Management Options” on page 48 for more
information about the rest mode.)

the page up or down while the cursor position does not
change. Pressing key combination again turns off the
scrolling function.

Decreases the LCD brightness.

Increases the LCD brightness.

When you press a function key combination, the system sound may be
temporarily muted.

Using the Keyboard 15

User Defined Buttons (SENS Keyboard)

You may program the three buttons to the right of the power button to start any
program you have installed on your computer.

User defined program

Internet Explorer

Outlook Express

The default settings for these buttons are:

Internet E-Mail - Outlook Windows Calculator

To reprogram the Sens Keyboard, follow the steps below:

1. Double-Click icon on the Windows taskbar, the Key Setting window is

displayed.

2. Select Button you wish to reprogram from the drop down menus in the Key
Setting window.

3. Use the Browse button to locate the program you wish to assign to the SENS
Keyboard button selected.

4. Click on your program choice to select it.

5. Click Open.

6. Click OK to close window and complete programming the Sens Keyboard.

16 Users Manual

Using the Touchpad

Your computer is equipped with a touchpad, which is an integrated-pointing device
that is used to perform standard mouse functions. The touchpad is an advanced and
reliable pointing device that works with a touch of your finger.

Touchpad

Mouse Buttons

Press on the touchpad gently. The touchpad responds to light pressure.

Scroll Button

Table 3. Using the Touchpad

Action Process and Comment

Click/Tap

Process

Depress the touchpad left button and release or position the pointer
over the object and Quickly tap the touchpad once with your finger.
This action is called clicking.

Comment

This will cause a process to begin or select an object on the screen.

Using the Touchpad 17

Action Process and Comment

Double-Click/Tap

Process

Quickly click the left touchpad button two times or position the pointer
over the object and Quickly tap the touchpad twice with your finger.
This action is called Double-clicking.

Comment

This will cause a process to begin or open a file folder.

Click-Hold

Right-Click

Scroll Up

Scroll Down

Process

Depress the left touchpad button and do not release.

Comment

This is used to move/drag objects to new locations. See ”Drag (Move)”
on page 19.

Process

Position the pointer over the object. Quickly press and release the right
button once.
This action is called Right-clicking.

Comment

This is usually used to obtain information about an object or access a
short cut menu.

Process

Place your finger on the top half of the button to scroll up the current
window.

Comment
Moves the current window down.

Process

Place your finger on the bottom half of the button to scroll up the current
window.

Comment

Moves the current window up.

PS/2 Mouse:

You may change the setup in Setup > Advanced Menu
Disabled prevents both the touchpad and external PS/2 port from functioning.
Single mouse (default) enables the external PS/2 port or the touchpad, and
external PS/2 port has priority. Dual Mouse allows the use of both the
touchpad and PS/2 port.

18 Users Manual

Drag (Move)

To move a window on the desktop, complete the following:

1. Click the window title bar or icon in the bottom of the window which you want

to drag using the touchpad.

2. Press the left touchpad button and hold it.

3. Drag the window using the touchpad.

Cursor in Windows

1

2

1 Click the Window

Title Bar and Hold

2 Drag your finger to
move the window

Area or Multiple item selection:

The drag function may be used to select an area or multiple items in an area
by clicking in one area and then dragging to create a selection window. The
items inside the window will be selected.

Title Bar

Using the Touchpad 19

Reading the System Status Lights

System Status lights show the status of computer functions.

Table 4. System Status Lights

LED Name Function

Num Lock Changes a portion of the keyboard to a numeric keypad.

See ”Using the Numeric Keypad” on page 14.

Caps Lock Changes all alpha or letter input into capital letters.

Scroll Lock Scroll lock in certain software.

Drive Access Using the Disk Drives.

E-mail Alert The Light comes on when e-mail arrives.

Power Green - System power on.

Battery
Status

No changes occur to numeric and special keys.

Blinking Green - HDD is being accessed
Blinking Amber - FDD or CD-ROM is being accessed

To use this function, you must register an E-mail Account in the Register E-mail
Account window. To register an E-mail account Select: Start > All Programs >

StartUp > Internet Launcher.

Blinking - Standby mode.

Green - No battery pack installed/battery fully charged.
Red - Charging.

20 Users Manual

Connecting to the Internet

This section explains how to connect you to the internet. For details on how to establish
the connection contact the Internet Service Provider [ISP] or system administrator
[SysAdmin].

Using the Modem

Install the Modem cable by simply plugging the cable into the slot in the back of the
computer.

Modem Cable

(Minimum 26 AWG)

1. Contact your Internet Service Provider to obtain information or CD required to
make the connection in your area.

2. After the cable is connected create a “Dialup” connection by clicking
Start > Control Panel > Network and Internet Connections.

3. Click Set up or change your Internet connection > Setup to start the connection

wizard.

4. Follow the instructions in provided in the Make New Connection wizard.

Connecting to the Internet 21

Precautions Before Use

Country Selection

Country Selection:

Because your computer is very mobile you must ensure you select the

country you are calling from is selected correctly, otherwise you may
experience connection problems.

To change the country selection proceed as follows:

1. Start > Control Panel > Network and Internet Connections.

2. Click Phone and Modem Options.

3. Click on the connection you wish to edit in the Locations: box.

4. Click Edit in the Dialing Rules Tab

5. Select the Country/region you are calling from in the General tab.

6. Click OK to close the “Edit Locations” box.

7. Click OK to close “Phone and Modem Options” box.

Digital Phone Lines:

If you connect the modem to a digital phone line (such as a company
4-wire system), the modem may be damaged.

DOS support

• Windows XP: Does not support pure DOS mode and the modem does not

support a DOS box in Windows. So you cannot use a
communication application which runs under DOS.

Using the Modem on a PBX system

If you use a Windows Communication Program:

1. Click Start > Control Panel > Network and Internet Connections.

2. Click Phone and Modem Options.

3. Click Properties in the Modems tab section.

4. Check off “Wait for dial tone before dialing” check box in the Modem tab section.

5. Click OK to close the dialog box.

6. Click OK to close “Modem Properties” dialog box.

22 Users Manual

If you use a simple terminal program (i.e. hyper terminal):

Type the “ATX3&W” or “ATX3” command as an initialization command.

MODEM Notes:

1. In order to use the 56K feature, be sure to check if the standards supported
by the on-line service provider and the modem are identical.

2. If you use a PBX phone system, you can not connect using the 56K mode.

3. Internationally connected calls will be limited to 33.6K (Max.)

Using the LAN

You may connect to the network using either a LAN cable or by establishing a wireless
connection if factory option is installed.

Cable Connection

Install the LAN cable by simply plugging the cable into the slot in the right side of the
computer.

Your computer’s LAN adapter is ready to use for most situations, however if your
system does not have a DHCP server or you wish to personally configure your LAN
connection, proceed as outlined in “Configuring Network Environment” below.

Network Protocols:

You may need to consult your SysAdmin if their network protocols and settings
are required for your LAN environment.

Connecting to the Internet 23

Configuring Network Environment

Configure the Network Adapter as follows:

1. Click Start > Control Panel > Network and Internet Connections

2. Click icon (Network Connections)

3. Double-Click the icon (Labeled Local Area Network)

4. Select Internet Protocol (TCP/IP) in the “This connection uses the following

items:” box.

Intel(R) Pro/100 VE Network Connection

5. Click Properties. The TCP/IP Properties window opens.

6. Click “Use the following IP address” in the General tab

7. In the “Use the following IP address” box, enter your IP address:, subnet mask:

8. In the “Use the following DNS server addresses” box, Enter your Preferred DNS

9. Click OK when you finish the TCP/IP set-up.

24 Users Manual

Step 7

Step 8

and Default Gateway:.

server: and Alternate DNS server:.

Wireless Connection (Factory Option)

Your computer’s wireless LAN adapter is ready to use for most situations, however if
your system does not have a DHCP server or you wish to personally configure your
wireless LAN connection, proceed as outlined in “Configuring Network Environment”
below.

FCC statement for Wireless LAN use:

“While installing and operating this transmitter and antenna combination the
radio frequency exposure limit of 1mW/cm2 may be exceeded at distances
close to the antenna installed. Therefore, the user must maintain a minimum
distance of 20cm from the antenna at all times. This device can not be co­located with another transmitter and transmitting antenna.”

The table below shows the Windows taskbar icons for the wireless LAN.

Icon Name Description

Connection
Established

Connection
Unavailable

Displays if connection is available.

Displays if connection is unavailable.

To display relative Signal Strength:

1. Double Click the icon in the taskbar to display the Wireless Network

Connection Status window. This window also displays connection Status, Speed,
Duration and Activity.

Network Protocols:

You may need to consult your System Administrator if their network protocols
and settings are required for your wireless LAN environment.

Connecting to the Internet 25

Configuring Network Environment

Configure the Wireless Network Adapter as follows:

1. Click Start > Control Panel > Network and Internet Connections

2. Click icon (Network Connections)

3. Double-Click the Wireless Network Connection icon. The Connect to Wireless

Network window pops up.

General Office Net

Supervisor Office Net

4. Select one of the available networks in the Available networks section, if
displayed.

No networks are displayed

Office - Consult your system administrator.

Home - Verify your access point is working properly.

5. Click the Connect button. The Wireless Network Connection icon in the control

Change Wireless Network Access Point as follows:

1. Right Click the Wireless Network Connection icon.

2. Click View Available Wireless Networks. The Connect to Wireless Network

3. Select the new network from the available networks in the Available networks

4. Click Connect button. The Wireless Network Connection icon in the control panel

26 Users Manual

panel will show your connection is Enabled. You may proceed using the network
as normal wired LAN connections.

window pops up.

section, if displayed.

will show your connection is Enabled. You may proceed using the network as
normal wired LAN connections

Using the Flex-Bay

The Flex-Bay provides an impressive array of secondary
storage devices listed below:

CD-ROM drive:

Shipped with some computers is also an available option.

CD-ROM R/W drive:

Shipped with some computers is also an available option.

DVD-ROM drive:

Shipped with some computers is also an available option.

DVD/CD-RW Combo drive:

Shipped with some computers is also an available option.

Optional secondary hard drive:

Available as an option for your computer.

Superdisk LS-120:

Available as an option for your computer.

If your operating system is Windows, you must install the Softex Bay Manager
software on the software CD in order to use the Bay Manager Utility to hot­swap the devices.

If you do not use Windows, make sure that the computer’s power is off before
you remove or install any devices.

Using the Flex-Bay 27

Remove/Install a Flex-Bay Device - Power On

You can use the Softex Bay Manager utility to hot-swap your devices in the flex-bay.

To start the Softex Bay Manager utility:

1. Click Start > Control Panel > Other Control Panel Options > Softex Bay
Manager.

- or -

2. Double-Click the SwapBay icon in the windows taskbar.

To remove a device:

1. Start the Softex Bay Manager Utility.

You do not have to turn the computer over or tip it on its side to change
devices. Simply tilt the computer up at the front about 10 cm and locate the
Flex-Bay latch. See Figure below for the location of the Flex-Bay latch. The
computer in the figure is tilted on its side for clarity.

Flex-Bay Latch

2. Click Remove / Swap. A Device Change popup window stating, “Please wait until

3. Tilt the computer up & locate the smart bay latch.

4. Slide and hold the device latch toward the front of the computer.

5. Slide the device out.

6. Click OK. The message “Please wait until the system processes the device change”

7. Click OK to close the Softex Bay Manager Utility.

28 Users Manual

the system processes the device change” appears then another popup window
appears and says, “Please remove or swap your bay device(s) now and press OK.”

appears again.

To insert a device:

1. Open the Softex Bay Manager Utility.

You do not have to turn the computer over to change devices. Simply tilt the
computer up and locate the Flex-Bay latch. See ”Bottom” on page 5 for the
location of the Flex-Bay latch.

2. Click Device Insert. A popup window appears stating “Please insert your device(s)
into the bay now and click OK.”

3. Insert the device.

4. Click OK to allow your computer to detect the device. The message “Please wait

until the system processes the device change” appears.

5. Click OK to close the Softex Bay Manager Utility.

Remove/Install a Flex-Bay Device - Power Off

Remove a Device:

1. Turn the computer’s power off.

2. Close the LCD panel, and turn the computer over so that the bottom of the unit

faces up.

3. Tilt the computer up & locate the smart bay latch.

4. Slide and hold the device latch toward the front of the computer.

5. Slide the device out.

Install a Device:

1. Turn the computer’s power off.

2. Carefully slide the device into the bay.

3. Push the device in until it is flush with the chassis and the Flex-Bay latch snaps

into place. Your computer’s operating system automatically recognizes the device
in the Flex-Bay and configures your computer accordingly when power is restored.

Using the Flex-Bay 29

Using the Disk Drives

Using the Floppy Disk Drive

Your computer comes with a 1.44 MB, 3.5-inch, floppy drive.

To use a floppy disk in your computer, insert it into the floppy drive.

To remove a floppy disk, press the floppy disk eject button on the front of the floppy
drive.

To protect the data on your floppy disks, follow the manufacturers guidelines.

Floppy Disk Eject Button

30 Users Manual

Using the CD/DVD-ROM Drive

Compact discs are designed so that you can easily insert one into the computer when
you need it, and then remove it. See ”Using the Flex-Bay” on page 27 for information
on installing the DVD-ROM drive into the computer.

DVD Notes:

A DVD player is a factory option and if you ordered this option you will have to
install the provided DVD software to view the DVD Title.

1. Press the button on the CD-ROM or DVD-ROM drive, and the tray slides out.
(Do not lean on the tray; because it will not support much weight.)

CD/DVD Drive Warnings:

Do not place reflective objects other than the CD/DVD disks in the disk slot
because of possible hazardous laser emissions. The laser beam used in this
CD/DVD-ROM drive is harmful to the eyes. Do not attempt to disassemble the
CD/DVD-ROM drive. Refer servicing to your authorized service center.

Do not touch the CD/DVD lens, doing so may damage the device.

CD/DVD Precautions:

The tray may be stuck, in which case straighten out a paper clip, insert
it into the Emergency Eject hole in the front of the CD/DVD-ROM and push it
until the tray ejects.

A LED on the drive tray is on when the computer is reading from a CD. Do not
remove a disc when this LED is on.

To clean a CD/DVD, wipe from the center outwards with clean and dry cloth.
Remove the CD/DVD when the drive activity LED is off.

2. Insert a CD/DVD, label side up (or remove a disc, if you have finished using it).

3. Push the tray in gently to close the drive tray.

CD-ROM Light

Emergency Eject Button

Eject Button

Install and/or start a CD-based program as you would run a program on a floppy disk.

Using the Disk Drives 31

Working with PC Cards

When you install PC Cards, you can add a multitude of functions to your notebook
computer similar to those found on add-in boards for desktop computers. There are
many PC Cards on the market, the supported PC Cards are listed below:

• Input/output, such as modem, network, video capture, and SCSI cards.

• Storage, such as hard drive and flash memory cards.

Your computer includes the following PC Card support:

• Two PC-Card slots: You can install Type I, II, or III cards in the slots.

TYPE III Cards:

Type III cards are thicker than Types I and II. If you install a Type III card in the
bottom slot, you cannot install a card in the top slot.

• CardBus hardware and software: CardBus enables the computer to use 32-bit

PC Cards. Windows XP supports 32-bit and 16-bit PC Cards.

• Zoomed video: Both PC Card slots and the video chip on your computer

support zoomed video. When you install a zoom video PC Card in the upper or
lower slot, data can be transferred directly from the PC Card to video and audio
systems without going through the microprocessor. Video conferencing and
real-time multimedia devices, such as video cameras, are supported by zoomed
video.

Maintaining PC Cards

To maintain your PC Cards, follow these guidelines:

• Keep cards away from excessive heat, direct sunlight, and liquids.

• Do not drop, bend, flex, or crush cards when handling.

• Keep dust, magnets, and static electricity away from PC Cards.

• When a card is not in use, carry it in its protective carrying case.

• Some PC Cards include cables that extend from the back of the cards. Be

careful not to bend or put excessive strain on these cables.

32 Users Manual

Using PC Cards

To insert a PC Card into a slot:

1. Push the slot door in with the PC Card.

2. Align the card with a slot and insert the card into the slot until it locks in place.

PC Card Eject Buttons

PC Card: (Example)
Insert PC Card with product
information facing up

Windows automatically assigns computer resources (such as communication ports and
memory addresses) to a PC Card installed in your computer.

To remove a PC Card from your computer:

Use the following procedures to remove PC Cards, or you may lose data that
is being stored to a card.

1. Click icon on the taskbar.

2. Select the card currently in use, and click the Stop button.

The eject button for the card slot operates in two steps, therefore to remove a PC Card:

PC Card Eject Buttons

3. Push the eject button once to pop it outward then push the eject button again to
eject the card.

4. Pull the card out of the PC Card slot.

Working with PC Cards 33

Multi Media Functions/Equipment

Media Player

You can play video and audio CD files with the Windows Media Player, as well as
watching TV, video and listening to the radio through internet. The on-board audio
hardware and software of your computer enable the computer to play audio/video
compact discs. The instructions to play a video CD-ROM are the same as the
instructions for the audio CD below. If you wish to do so, you can attach external
speakers to the Headphone jack.

Playing a Audio/Multimedia CD

To play an CD follow the instructions below:

1. Insert a compact disc into your CD-ROM drive.

2. Press the button on the CD-ROM drive to open the CD-ROM device.

3. Insert a CD, label side up.

4. Carefully push the tray in to close the drive tray. The Windows Media Player

button appears on the taskbar if not already there, and the music begins to play. If
the disk does not play click Start > All Programs > Accessories >
Entertainment > Windows Media Player.

CD LED On:

A LED on the drive tray is on when the computer is reading from a CD. Do not
remove a disc when this LED is on.

Removing the Audio/Multimedia CD

To remove the CD follow the instructions below:

1. Click Start > All Programs > Accessories > Entertainment > Windows Media

2. Click Stop in the Windows Media Player window or simply close the Windows

3. Press the button on your CD-ROM drive. The drive tray opens and you can remove

4. For more information on playing compact discs, see the Help menu in the

34 Users Manual

Player to open the Windows Media Player window, if not already open.

media player.

the CD from the CD-ROM drive.

Windows Media Player window.

Dolby Digital & Dolby Theater System

Your computer supports Dolby Digital & Dolby Theater System through a SPDIF
connector, located next to the volume control wheel on the left side of the computer.
You must have a 3.5 mm (mono)- to RCA cable to use this port.

Volume Control

Using the Wheel Volume Control

Simply turn the wheel located on the left side of the computer.

Wheel Volume Control

Using the Keyboard

Changing the volume with your keyboard.

Use to decrease the volume or to increase the volume.

+ +

Using the Volume Control Icon

Double-Click icon in the active program tray. The Volume Control window pops
up. Use this window to adjust the volume. You can pop up a simple volume slider by
a single click icon.

Multi Media Functions/Equipment 35

Movie Maker

You can edit audio and video data using this Movie Maker included with Windows XP.
It is also possible to make a slide show with each frame or picture.

To start the program:

Click Start > All Programs > Accessories > Windows Movie Maker.

Please refer to the on-line help manual to operate the Windows Movie Maker.

36 Users Manual

Using the Battery

Your computer uses a smart rechargeable Lithium-ion (Li-ion) battery pack for power
when the AC adapter is not attached to an electrical outlet. The smart battery gives a
accurate measurement of the current battery capacity which helps extend operating
time by enabling effective power management in operating systems that take
advantage of the accurate information supplied by the battery.

Charging the Battery

Your computer’s battery starts charging automatically when you connect the power to
the computer and to an electrical outlet. If the computer is off, the battery charges faster
than if the computer’s power is on.

Approximate charging times for the Li-Ion battery are

• 3 hours with the computer off.

• 7 hours with the computer on.

While the battery is charging normally, the battery charge light on the computer is red.
When the battery is fully charged, the light changes to green.

When you use a new battery pack for the first time or use a battery after a long period
of storage, the initial battery life is shorter than normal. Normal battery life resumes
after a few discharge-recharge cycles.

Follow these rules for charging your battery:

• A battery normally discharges power when not used for long periods of time.

Be sure to recharge the battery every two months when it is not in use.

• Make it a practice to discharge your battery fully before recharging the battery.

This can help extend the life of the battery.

• Do not attempt to charge the battery in temperatures of under 5

o

C or over 35oC

All batteries eventually wear out and lose the ability to hold a charge. You may
need to replace your battery pack after a year of average usage.

Using the Battery 37

Safely Using the Battery

Follow these guidelines to safely use the battery:

• Turn off your computer and unplug it if you accidentally:

– Expose the equipment to liquid.

– Drop, jar, or damage the computer.

• Use only approved battery chargers.

• Do not disassemble the battery, heat it above 100°C, or burn it. The battery

used in this computer may cause a fire or chemical burn if mistreated.

• Your computer's rechargeable battery may be considered hazardous waste. If

you replace your battery with a new one:

– Keep the old battery out of the reach of children.

– Dispose of the old battery promptly.

– Make sure that you follow all local requirements when you dispose of the

old battery.

Removing the Battery

Your computer comes with the battery pack inserted in the computer.

To remove the battery from the computer:

1. Turn the computer’s power off.

2. Close the LCD panel, and turn the computer over so that the bottom of the unit

faces up.

3. Slide the battery compartment cover straight up and off the computer.

4. Fold down and grasp the wire tab then pull the battery out of the compartment.

38 Users Manual

Installing the Battery

To install the battery pack:

1. With the computer’s power off, close the LCD panel and turn the computer over

so the bottom of the unit faces up.

2. Slide the battery compartment cover straight up and off the computer.

Insert the battery into the battery compartment, ensuring the correct
orientation so that the battery fits in its slot properly.

3. Slide the battery pack into the compartment. Make sure the battery is fully inserted
into the compartment. Carefully fold up the wire removal device.

4. Align the tabs on the battery compartment cover with the slots on the battery
compartment.

5. Push the cover straight down until it snaps into place.

Monitoring the Battery Charge

Battery life is affected by factors such as the power-management settings in System
Setup, the applications you use, and the brightness settings of the LCD. Under normal
usage, the battery charge lasts approximately 3 hours.

Battery life estimates are subject to variation. The actual life of your battery
may be less than the estimates given in the manual.

You can monitor the charge of the battery pack installed in your computer by using the
Power Meter or Battery Gauge.

Using the Battery 39

Power Meter

The Power Meter displays the charge of the batteries and the current source of
computer power, AC or batteries. You may monitor the battery charge or usage by
using the “Power Meter”. To access the power meter click icon on the task bar or
click Start > Control Panel > Performance and Maintenance > Power Options >
Power Meter Tab.

The Power Status icons shown below are displayed

during Battery Charging Operations

At ~15% and 10% remaining battery power the

current power source and the battery Icons

respectively change to the icon shown below and

you should follow the instructions in “Battery

Warnings” section below

You may also check battery charge by moving the cursor to the icon, a small dialog
box will display the % of charge.

Battery Gauge

You may display the battery gauge while you are in any program by pressing

Gauge

+

disabled. The battery gauge is only displayed for a few seconds.

Power Source:

. While the battery gauge is being displayed, all keys except are

Battery Level:

40 Users Manual

• Indicates that the computer is powered by the AC adapter.

• Indicates that the computer is powered by the battery.

• The top/right section indicates the approximate amount of the

primary battery charge remaining.

Battery Warnings

If the battery charge is low (about 10%) you have approximately 5–10 minutes of
battery life left. You should:

• Save your work and,

• Connect the power cord to the computer or turn off the computer and install a

fully charged battery.

You can adjust the battery alarm features by using the operating systems power
management program (Start > Control Panel > Power Options in Windows).

If you cannot run your computer from the battery and the battery will not charge when
you attach the power cord, the problem may be that:

• The battery temperature is below 10°C or over 32°C. If you think the battery

temperature is too hot or too cold, turn off the computer, remove the battery,
and let the battery reach room temperature. Then try charging the battery again.

• The battery is defective. Replace the battery with a new battery.

Battery Calibration

Calibrating your battery once a month is one of the recommended methods of
increasing your computer’s battery life. To calibrate the battery complete the following
steps:

Calibration Notes:

You should start the battery calibration process with a fully charged battery,
battery status LED is green. The power meter may not show 100%.

Before you commence the battery calibration process you should fully charge,
then fully discharge and finally fully recharge the battery again.

1. Disconnect the AC power adapter after turning off the system.

2. Restart your computer and press <F2> to enter BIOS setup.

3. Using the arrow keys, highlight Battery Calibration in the Power menu.

4. Press Enter to start calibration process. The calibration usually takes 2 to 3 hours

depending on the current battery charge.

5. When the calibration process is complete, recharge the battery fully.

Using the Battery 41

Using System Setup

The System Setup (BIOS) program enables you to configure your computer hardware
and set security and power-savings options. The settings you choose are stored in
battery-maintained CMOS memory that saves the information even when the
computer’s power is turned off. When your computer is turned back on, it is configured
with the values found in this memory.

Run System Setup if you get a message prompting you to run the program. You may
also want to run System Setup, particularly the first time you use your computer, to set
the time and date, use security or power-management features, or alter the settings of
other features.

BIOS Caution:

If you are not familiar with BIOS setup and what the parameters mean, seek
help from a person who is knowledgeable. Incorrect settings may cause your
system to “Crash”.

Starting System Setup

To start System Setup, turn on your computer and then press and hold until the
System Setup screen appears.

Table 5. System Setup Menus

Menu Function

Main Changes the basic system.

Advanced Configures advanced features on your computer.

Security Enables security features, including passwords and backup

Boot Specifies the order of boot devices and configures boot

Exit Specifies how to exit System Setup.

To open the menu you need to use, use the left or right arrow keys to select the menu
name.

and virus-check reminders.

features.

42 Users Manual

Table 6. System Setup Navigation Keys

Navigation Key Function

Displays the General Help window.

Exits the current menu.

or

or

Moves the cursor up and down between fields.

Selects different menus. Pressing the ESC key at the Main
menu brings you to the Exit menu.

Scrolls backwards through the options for the highlighted field.

Scrolls forward through the options for the highlighted field.

Sets the parameters for the current menu to their default
values.

Sets the parameters for the current menu to their previous
values.

Executes commands or opens a submenu.

Using System Setup 43

Changing Booting Priority

The Boot menu in System Setup enables you to select the booting device and to set
booting options.

Boot Device Priority field enables:

You to select the order in which the computer attempts to boot from different devices.
The field has three (3) options: DVD/CD-ROM Drive, Removable Devices and

Hard Drive.

To change the booting device priority, choose the device positions by completing
the following:

1. At startup, press <F2> to open System Setup.

2. Use to select the Advanced CMOS Setup menu.

3. Highlight the 1

4. Press <Shift+Plus> keys until the option moves up in the list to the desired

position or press <Minus> key until the option moves down in the list to the
desired position.

5. Press <Esc> to return to the Exit menu.

6. Press Enter or <F10> to exit and save your changes.

7. Press Enter again to restart the computer.

st Boot Device option with keys.

or

44 Users Manual

If you want to start the system using a bootable CD, change the CD-ROM
Drive to be the 1

st Boot Device.

Using System Security

This section describes your computer security programs. The first is the standard BIOS
security which is standard on almost all computers. The second is a advanced factory
option Biometric security system that uses your fingerprint(s) to control access to your
computer and individual files if necessary. You no longer have to worry about
passwords being lost, stolen or forgotten.

BIOS Security

The BIOS security operations are explained below:

System Passwords

The computer provides (4) levels of password security: administrative-level
(supervisor), user-level (user), HDD access and Password on Boot. These passwords
prevent unauthorized access to the computer. The supervisor password enables full
access to all System Setup fields. The user password enables full access to only the Set
User Password and Password on boot security fields and read access to all other
System Setup fields. The HDD Password controls access to the hard drive.

You may also enable the biometric security at boot.

The (3) security boot time options are:

The Biometric Security software MUST be installed prior to setting the security
options to any of the fingerprint options.

• Disabled

• Text password

• Finger Print

If multiple users have access to the computer (such as in a network environment), a
supervisor password can prevent unauthorized access to certain security options.

Choose the type of password security that is appropriate for your work.

Using System Security 45

If You Forget Your Password

It is very important that you do not forget your password. If you do, you cannot access
your system. Write your password down and keep it in a safe place. If you do forget
and cannot find the written note, please contact the Samsung Helpline. Please have
your receipts available to verify the type and model of your computer. You may be
charged for password removal.

Creating a Password

To create a password follow the instructions below:

1. At startup, press to open System Setup.

2. Use to select the Security menu.

Precautions for Password Entry:

You can enter letters or numbers, but you cannot use the function keys, such
as the Shift key. Your computer does not distinguish between capitalized and
lowercase letters in your password. As you type the password, the cursor
moves but your password does not appear on the screen. Choose the type of
password security that is appropriate for your work. If you want to set a user
password, you must set a supervisor password first.

3. Use to select Set Supervisor Password or Set User Password.

4. Press <Enter>. The Set Password dialog box appears.

5. Press <Enter> after you have typed your password. The computer prompts you to

reenter your password for verification.

6. Type your password again and press <Enter>. A message appears telling you that
the changes have been saved.

7. Press <Enter> again to return to the Security menu.

8. Press to go to the Exit menu.

9. Press <Enter> or <F10> to exit and save your changes.

10. Press <Enter> again to restart the computer.

46 Users Manual

If password use is not desired:

Follow the creating a password procedure above except leave the password field empty in
step 5.

Biometric Security

The factory optional fingerprint sensor provides unique
security access to your computer. You will no longer have to
worry about losing or forgetting your password. Since every
person has a unique set of fingerprints, only a biometrically
enrolled person may have access to your computer.

Advantages of Biometric Security are:

• Very high level of security

• No password to remember, lose or have stolen.

• Streamlined logon process.

• Single fingerprint will access many programs, eliminating passwords.

If you purchased the Biometric Security option, please refer to the manual provided for
installation and use.

Using System Security 47

Using Power Management Options

Your computer includes Power Management options that can help the battery charge
last longer and extend the life of the battery. Power-management options will slow
down or shut off system components when the components are not being used.

Power management may slow down system performance. Your computer runs fastest
with the power cord attached, when power management is disabled.

In the next sections, basic and advanced methods of power management will be
discussed.

Basic Power Management Schemes

This section discusses the basic schemes of power management when the computer is
operating on battery power or using AC power.

Standby vs. Hibernation

Standby unlike hibernation mode does not store unsaved information on your
hard disk; it's stored only in the computer memory. If there is an interruption in
power, the information is lost. So before putting your computer on standby,
you should save your files.

Changing Devices:

Do not change PC Cards while in standby or hibernate modes.

To enter the power management window complete the following:

1. Click Start > Control Panel > Performance and Maintenance.

2. Click icon to display the Power Options Properties window.

48 Users Manual

3. Click the Power Schemes tab to display the basic power management options.

Power Schemes Tab

4. Select the time that you wish each of the following actions to occur in Battery and
AC power mode.

• Turn off monitor:

• Turn off hard disks:

• System standby:

• System hibernates:

Turning off the monitor and HDDs will save a substantial battery power, therefore
when in battery only mode select the shortest time practical.

a Hibernate Mode (Power Management or Manual Method)

When hibernation is used, your computer turns off and when you power up again,
everything is restored exactly as you left it—including programs and documents
you may not have saved or closed. Everything in memory gets saved to the HDD,
and the monitor and hard disk get turned off.

Using Power Management Options 49

If You Reinstall Windows:

You should re-establish hibernate in power options by opening

Power

Options Properties window and click on the Hibernate tab then click

“Enable Hibernation”.

Hibernate Tab

Frequent Interruptions:

If you experience frequent interruptions, you might also consider putting your
computer into automatic hibernation after a specified number of minutes using
the power management options.

a Standby Mode (Power Management or Manual Method)

Standby is used mainly for conserving battery power in your notebook computer. It
also gives you the benefit of getting right back to your work without waiting for the
computer to restart. Standby turns off your monitor and hard disks, placing your entire
system in a low-power state. When you return to your computer, restores your desktop
exactly as you left it. It is recommended that you do not enter standby mode with less
than 20% battery power.

5. Click OK to set your power management options and close the window.

50 Users Manual

Rest Key:

The manual <Fn+F11> key combination will not activate Standby
or Hibernate modes whilst you are playing a multimedia program or have an
active USB device connected.

+

Advanced Power Management Schemes

This section discusses the advanced power management schemes. There are two
buttons that you can use to manually conserve power.

To enter the power management window complete the following:

1. Click Start > Control Panel > Performance and Maintenance.

2. Click icon to display the Power Options Properties window.

3. Click the Advanced tab to display the advanced power management options.

Advanced Tab

Power & Sleep Button
Programming Windows

4. Select the mode (Do nothing/Ask me what to do/Standby/Hibernate/Shut
down) assigned to the Power button and/or Rest

<F11> key. Also select the

action (Do nothing/Standby/Hibernate) associated with closing the computer
lid.

The “Rest” key is assigned to the <Fn+F11> key combination.
See ”Basic Power Management Schemes” on page 48 for a better
understanding of Standby and Hibernate modes.

+

5. Click OK to set your power management options and close the window.

You can return to normal operation after you have used one of the “Power
Management” buttons by quickly pushing and releasing the Power button.

Using Power Management Options 51

Using the Hard Drive

Your computer includes a removable IDE (integrated drive electronics) hard drive. The
IDE hard drive can store the data and programs your computer uses. The drive plugs
into a connector on the system board.

The hard drive that comes with your computer has already been formatted. Do
not format the hard drive. Doing so destroys all data contained on the drive. If
you need to format a new drive, or want to erase all data on your existing hard
drive, refer to the manual for your operating system.

Removing the Hard Drive

To prevent loss of data and damage to the disk, do not remove the hard drive
while the computer’s power is on and do not drop or jar the hard drive.

To remove the hard drive from the computer:

1. If you are installing a new hard drive, backup the application and data files on the

old hard drive before removing it from the computer.

2. Turn the computer’s power off.

3. Close the LCD panel, and turn the computer over so that the bottom of the unit

faces up.

4. Remove the screw that holds the hard drive in place.

5. Pull the hard drive out of the computer.

52 Users Manual

Bottom of computer

Hard-drive

Installing a Hard Drive

To install a hard drive:

1. Remove the old hard drive from the computer as described in the previous section.

2. Slide the new drive into the hard drive compartment. Make sure the drive is pushed

back as far as it will go.

3. Install the screw that holds the hard drive in place.

4. If required install windows and appropriate device drivers according to the

instructions below.

(Re)Installing Windows and Device Drivers

Use System Recovery CD to (re)install OS and System Software CD to (re)install
device' drivers.

The System Recovery CD is used to (re)install the OS and System Software
to a new HDD or recover from a system crash.

Notebook computers that ship from the factory include System Recover CD­ROM and System Software CD-ROM, which contains a copy of the
applications and drivers needed for computer's operating system.

In the unlikely event that programs on the computer hard drive become
corrupted or are erased, you can use the System Recovery CD-ROM to
reinstall your operating system and then System Software CD-ROM to
reinstall your original applications and drivers.

Using the Hard Drive 53

Video Features and Configuration

All these video modes can be displayed on an external monitor. However, if you
disconnect an external monitor that was attached to your computer and then start the
computer, the LCD may revert to a different resolution than the one you chose for the
external monitor.

Resolution and Colour Depth

The resolution of the LCD is the sharpness of the image it can display. Resolution is
measured by the number of pixels (individual dots) displayed on the entire screen. In
general, the more pixels the LCD can display, the better the image.

The number of colours the LCD can display is measured by how many bits the LCD
uses to represent each pixel:

• 16-bit colour can support 64 K (65,536) colours.

• 32-bit colour can support 16 M (16.8 million) colours.

All these video modes can be displayed on an external monitor. However, if you
disconnect an external monitor that was attached to your computer and then start the
computer, the LCD may revert to a different resolution than the one you chose for the
external monitor.

54 Users Manual

Configuring Display Features

The following sections describe how to configure the display settings on your
computer.

Display Resolution Notes:

When Windows XP is initially installed it will automatically adjust the resolution
to maximum available.

Changing Colour Depth and Resolution

To change the colour depth and resolution of your LCD or external monitor:

1. Click Start > Control Panel > Appearance and Themes.

2. Click icon. The Display Properties window appears.

3. Click the Settings tab. The Settings screen appears.

4. To change the colour depth, click the arrow next to the Colour quality palette and

select the available colour depth you want.

5. To change the resolution, click and drag the slider under the Screen resolution
until you select the available resolution you want.

6. Click OK.

7. Follow the prompts that appear on the screen.

Video Features and Configuration 55

Using Dual View Mode

Single View mode is the basic display mode which displays same view on all the
display devices connected to a system.

Dual View mode is the “Extended screen mode” supported in Windows, which
displays separate views on each display devices connected to a system.

The default setting on your system is Single View mode.

Setting Dual View Mode

To set Dual View mode on your system:

1. Connect peripheral display device such as monitor or TV to your system and start

the system.

2. Select Start > Control Panel > Appearance and Themes.

3. Click icon. The Display Properties window appears.

4. Click the Settings tab. The Settings window appears.

5. Check Extend my Windows desktop onto this monitor.

6. You can drag the second monitor image to position where you want your extended

screen space with respect to the primary monitor (usually the LCD).

To confirm whether the system is set properly with Dual View mode:

1. Open Display properties and click Settings tab.

2. Place the cursor on the first monitor picture and click and hold over a second, a

number 1
the second monitor picture and click and hold over a second, then digit number 2
will be shown on the second actual monitor screen.

3. The monitor displays digit number 1 is the primary monitor and number 2 is the
secondary monitor.
In Windows explorer, the program is displayed on the primary monitor, if you can
drag it to the secondary monitor, then Duo View mode is now working properly.

will be shown on the first actual monitor screen. And place the cursor on

56 Users Manual

The secondary monitor has a display of 256 colours (colour depth) and 640x480 pixels
(resolution) at first. The colour depth and resolution of primary/secondary monitors are
separately changeable.

To reset the system to Single View mode:

1. Start Display properties.

2. Click Settings tab.

3. Click the second monitor among two monitor pictures.

4. Uncheck Extend my Windows desktop onto this monitor.

5. Click OK.

Using Dual View Mode 57

Using the TV-Out Port

Using the TV-out port, a compatible TV or other compatible display device can be
connected and an image displayed. No Audio is transmitted through the TV-Out port.
To check if and how your TV displays the TV-out signal see the documentation
included with your TV. You must also insure that (TV/Video) is changed to Video
mode using the TV remote controller or the buttons on the TV set.

To enable TV-out:

1. Connect the TV to the TV-Out port using an appropriate cable.

2. Click Start > Control Panel > Appearance and Themes.

3. Click Display > Settings

4. Ensure Extend my Windows desktop onto this monitor box is unchecked.

5. Click Advanced > Display.

6. Click the check box to the left of the text “TV”.

7. Follow the screen prompts and the LCD screen display will be duplicated on the

television.

If the TV symbol is grayed out then the system has not detected a TV, check
that the TV standard in the System Setup is set correctly and that the TV is
turned on and connected properly. You can not use TV-out port in DOS mode.

8. Click Apply or OK.

58 Users Manual

Using Options

You can order the following options for your Notebook computer from your authorised
reseller:

• An extra AC adapter.

• An auto adapter that enables you to charge the computer’s battery and operate

the computer while in an automobile.

• An extra battery pack.

• An upgraded hard drive. Optional hard drives are available to fit in the hard

drive compartment or the Flex-Bay.

• 128, 256 and 512 MB DDR SDRAM memory modules that enable you to

upgrade your computer’s memory to a maximum of 1 GB.

• A CD-ROM drive module (CD Only or CD R/W).

• DVD/CD-RW Combo drive:

• A DVD-ROM drive module.

• A Superdisk LS-120 drive.

• Docking options that enable you to use your computer like a desktop computer.

• Wireless LAN

• IrSTICK

The options that are available may change periodically. Contact your reseller for
updated information on current and new options.

TM

Memory Modules

You can increase system memory by installing optional memory modules. You can
install a 128 256 or 512 MB modules.

To avoid possible system problems, use only approved memory modules in
your computer.

Using Options 59

Before You Install Memory

To prevent personal injury and damage to the equipment, follow the
precautions listed here before installing a memory module.

Take the following precautions when installing a memory module:

• Before you remove the memory module compartment door, turn off the

computer, unplug the power cord, and remove the battery. Also, disconnect any
peripheral devices.

• Before handling a memory module, discharge any static electricity by touching

a grounded surface or using a grounding wrist strap.

• Do not insert objects with conductive material, such as metal screwdrivers or

graphite pencils, into the memory-module compartment.

• Be careful in handling the metal plate of the memory door.

Installing a Memory Module

Handle a memory module carefully. Hold them only by the edges.

To install a memory module:

1. Turn the computer over so that the bottom faces up.

60 Users Manual

2. Using a screwdriver, remove the screw that holds the memory-module
compartment door in place.

3. Grasp the edge of the door and pull the door off the chassis.

4. Remove installed modules if necessary:

5. Align the connector on the memory module with the connector of the slot.

6. Push the memory module into the slot at a slight angle until the connectors are fully

engaged.

o

45

7. Push down on the edge of the memory module until the module snaps into place.

8. Align the memory module compartment door with the compartment and push the

door down until it snaps into place.

9. Reinstall the screw you removed in step 2.

10. Turn on the computer and perform a complete POST to check the memory

integrity.

Using Options 61

Docking Options

Contact your reseller for a list of docking options available for your Notebook
computer. User’s manuals are included with the docking options.

Wireless LAN

The wireless LAN option allows easy connection to large or small office networks
while also providing freedom from the constraints of cables and sockets.

To setup and use the Wireless LAN, Please refer to the user manual provided with the
option at the time of purchase.

62 Users Manual

Troubleshooting

Complete the following in the order presented until your system is functioning
properly. If all of the steps below fail then contact your local reseller for assistance.

 Questions and Answers

Please see “Questions and Answers” on page 64 for assistance in correcting any
computer operational problems.

 Check the Connections

Verify all of the power and peripheral cables are securely plugged into their sockets
and that your system and power supply is on.

 Norton AntiVirus

Run Norton AntiVirus to insure a virus is not affecting your computer.

To run Norton AntiVirus proceed as follows:

Click Start > Programs > Norton AntiVirus > Norton AntiVirus 2002

 Windows Help and Support

Run Windows Help and Support to find problem that may be affecting your
computer.

To run Windows Help and Support proceed as follows:

Click Start > Help

 Reinstalling Software

If for some reason your system crashes you may corrupt your HDD, Windows
Operating system and/or some of your device drivers. If this is the case, use System
Recovery CD to reinstall OS and System Software CD to reinstall the corrupt device
drivers.

System Recovery Precaution:

Before you start restoring your windows operating system insure you backup
all data on your hard drive.

Samsung is NOT responsible for any data loss.

Troubleshooting 63

Questions and Answers

Operating System Problems

Problem Action

The computer does nothing
when you turn it on.

Some of the letter keys type
numbers instead of the
indicated letters.

Battery power seems to run
out faster than expected.

Certain software programs
“hang” during operations
when there is no interaction
with the keyboard or
peripheral devices.

PC Card does not work
correctly.

Your ATA or Compact
Flashcard do not work.

The System Setup settings
are not retained when you
turn off the computer.

Has the battery run down? Connect the power cord
to the computer and recharge the battery. Try turning
on the computer again.

Is the Num Lock light on? If so, the numeric keypad
on the keyboard is active. To return the keypad keys
to typing letters, press <Num Lock>.

If you are running the computer from the battery
rather than the power cord, make sure that you set
the Idle Mode field in System Setup to On. This
setting enables the microprocessor and the hard
drive to slow down when the computer is not busy.

Your computer may be in Suspend or Rest mode.
Tap the touchpad to resume from Suspend or press
the power button to resume from rest.

Make sure that the PC Card is inserted left side up in
the PC Card slot. Check that the card is inserted fully
into the slot. If you are using a PC Card modem,
check the modem cable connections.

A patch is provided for these cards on the Recovery
CD

The CMOS battery inside the computer may need to
be replaced. The CMOS battery provides power to
save the system BIOS information when the
computer is turned off. Normally, the CMOS battery
lasts for several years. Do not attempt to open the
chassis and replace this battery yourself or your
warranty is void. Have an authorized the
manufacturer’s service center replace the CMOS
battery.

64 Users Manual

Problem Action

No sound.

System/BIOS behaves
erratically

Video Problems

Problem Action

Nothing appears on the LCD
panel when you turn on the
computer.

Error Message when
entering Power Management
while in Multimonitor mode.

Nothing appears on the
external monitor when you
switch the display to it.

Only the LCD Display works
when system returns from
Power management mode
while in Multimonitor mode.

The external monitor
displays flashes or waves.

Verify if the mute check box is checked or the
volume is not turned down in the pop up menu by
clicking the speaker icon of the task bar.

If you caused an abnormal power interruption (i.e..
removing battery while on battery power), you may
cause BIOS data corruption.

Adjust the brightness on a TFT LCD. Are you using
an external monitor? If so, press <Fn+F5> to return
to the LCD panel.

If the secondary monitor is set to 256 colours, this
error message could appear. Change the colour of
the secondary monitor to ‘high colour (16 bit)’.

Is the monitor properly connected to the computer?
Is the monitor’s power cord connected to an AC wall
outlet? Check the brightness and contrast controls on
the monitor. Does the program appear on the LCD
panel instead of the external monitor? If so, press
<Fn+F5> to switch to the monitor. Try turning the
monitor off and on again.

The system resets to the original BIOS setup when
the system returns from the power management
mode. If the Display mode, in the Advanced menu of
BIOS setup is set to LCD, then only the LCD will be
turned on when the system wakes up. Set the Display
mode in the BIOS to Both to turn on the LCD &
CRT on wakeup.

Check the cables between the monitor and the
computer. Are they properly installed?

Troubleshooting 65

Problem Action

Cannot toggle between CRT
and LCD while playing the
3D game.

There is LCD or CRT has
noise (speckles, lines or
raged edges) on the
picture when playing a
MPEG file with the Media
player/ DVD software or
using the USB camera.

In DOS mode the CRT/LCD
button does not work.

If the connected CRT
monitor display is not steady.

If you are using the Multimonitor mode, you can not
use the <Fn+F5> key combination and also you
cannot use this function in 3D games using Direct­X.

Adjust the resolution and the colour to 1400 x 1050
and 32 bit to display clearly, or avoid playing two
programs at the same time.

The LCD only mode is not supported using this Key
combination.

If the refresh rate is not optimal for the connected
CRT, then this problem may occur.

To correct this problem do the following:

1.Click Start > Settings > Control Panel.

2.Double Click the Display icon to open the Display
properties.

3.Select Settings

4.Click the Advanced button.

5.Click the Adapter tab

6.Adjust the Refresh rate to optimal or other selections

until you see the CRT clearly.

66 Users Manual

Modem Problems

Problem Action

My modem doesn't connect
to services or disconnects
during communication

When using a PBX phone
system I can't dial on my
modem.

Screen displays random or
garbage characters during
communications.

Reports error message that
insufficient Hard Disk space
is available.

If your modem has difficulty in connecting to on­line services and sustaining communications, first
check if other devices are connected and remove
them. Also remove any extension leads. Interference
from certain devices or poor line power conditions
may degrade the quality of your connection. Under
these conditions gradually reduce the
communication speed of your modem until a reliable
connection is achieved.
Check with your on-line service provider.

If you use a PBX phone system you may need to
press a number i.e. '9' to connect to an external line,
you should enter the following command before
trying the connection and check modem
initialization. (ATX3&W)

And add “9,” as the external line prefix (example) of
the phone number when using the dial command
“ATDT9, 123-4567”.

After your modem has connected to the on-line
service, your screen may display garbage characters
or after-images in screen transitions. This problem is
caused by a mismatch of the terminal modes
between communications service and
communications programs. You need to match the
terminal modes to each other. Refer to the user's
guide of the communications program you're using.

Delete the unnecessary messages or data you
received by Modem or Fax every one to three
months as required.

If you're using the internet, many picture and data
files can get downloaded to your HARD DISK every
time you visit a home page, which will consume a lot
of your HARD DISK space. For more detailed
information about the method of deleting, refer to
the help of the Web browser you've been using or
your user's guide.

Troubleshooting 67

FAX Problems:

Depending on telephone line status, or types of Fax machines/programs that
send/receive the Fax, Fax transmission/reception may not work correctly. In
that case, please try other Fax programs. (e.g. Win Fax)

Reinstalling Software

Windows Application/Driver (Re)Installation

If you wish to reinstall drivers or applications, please use the Software CD.

If you wish to reinstall the Windows operating system, please use the Recovery CD.

Application/Driver (Re)Installation

Simply install the driver(s) according to the instructions below:

1. Insert the System Software CD-ROM.

2. Follow the directions provided in the opening window.

Windows (Re)Installation

To reinstall the your Microsoft Windows XP Operating System:

1. Start your computer.

2. Open the CD Drawer and insert the Recovery CD. Close the drawer.

3. When the Recovery Menu appears, select the option as required to restore your

system. You have two options for system recovery. The Standard Installation and
the User Installation.

• The Standard Installation Option will SAVE all user data files on your hard

disk and restore your operating system to normal.

• The User Installation Option will DESTROY all data on your hard disk. If

you have any data files or other software you do not wish to lose, make a
backup of these files to a diskette or other medium using a backup utility
before proceeding.

Samsung is NOT responsible for any data loss.

68 Users Manual

You MUST, however reinstall all of your applications and drivers using the
Software CD and other application software as required.

If the Recovery Menu does not appear, proceed as follows:

1. Restart your computer

2. Open the CD Drawer and insert the Recovery CD. Close the drawer.

3. You will see a message “Press any key to boot from the CD”, press any
key.

4. You will be presented with the User Installation Option.

If your computer cannot boot from the CD, change the boot priority to the
CD-ROM device as described in this manual.

Troubleshooting 69

Specifications

Dimension

* LCD viewing area

LCD viewing area (15” TFT) 304.8 x 228.6 mm

Width 32.4 cm

Depth 27.2 cm

Height 4.1 cm

Weight (with integrated floppy drive,
Li-Ion battery & 14.1” TFT LCD & weight saver)

Environment

Ambient temperature, operating 10o–32oC

Ambient temperature, storage -5o–40o C

Relative humidity (noncondensing), operating 20–80%

Relative humidity (noncondensing), storage 5–90%

Altitude, operating 0 to 2,348 m

Altitude, storage 0 to 12,192 m

Shock, operating 10 G for 11 ms half sine

Shock, nonoperating 60 G for 11 ms half sine

Lithium-Ion Smart Battery

Normal Weight 500g

Nominal open circuit voltage 11.1 VDC

Capacity, typical 6450 mAhr, 72.0whr

Charging time, approximate, with computer turned off, typical 3.0 hr

Charging time, approximate, with computer turned on , typical 7.0 hr

Average battery life, with power management enabled 3.0 hr

External AC Adapter

Operating voltage 100-240 VAC

Line frequency 50-60 Hz

Input current 1.5 A 100 V ~ 0.8 A 240 V

Output current 4.2 A

Output voltage 19.0 VDC

3221 g

70 Users Manual

Abbreviations

A . . . . . . . . . Amperes

AC . . . . . . . . Alternating current

ACPI . . . . . . Advanced Configuration and Power management Interface

APM . . . . . . Advanced Power Management

ATA. . . . . . . AT attachment (refers to the hard-drive interface in an AT-

ATAPI. . . . . AT attachment packet interface

BBS . . . . . . . Bulletin board system

BIOS . . . . . . Basic input/output system

C . . . . . . . . . Centigrade

CD . . . . . . . . Compact disc

CD-ROM . . Compact disc read-only memory

cm . . . . . . . . Centimeters

COM . . . . . . Communication (as in communication port)

CMOS . . . . . Complementary metal-oxide semiconductor

DC . . . . . . . . Direct current

DMA . . . . . . Direct memory access

DPMS . . . . . Display power-management signaling

DRAM. . . . . Dynamic random access memory

DSTN . . . . . Double layer super twist nematic

ECP . . . . . . . Extended capabilities port

EPP . . . . . . . Enhanced parallel port

g . . . . . . . . . . gram

G . . . . . . . . . Gravity

GB . . . . . . . . Gigabytes

hr . . . . . . . . . hour

Hz . . . . . . . . Hertz

IDE . . . . . . . Integrated drive electronics

I/O . . . . . . . . Input/output

IRQ . . . . . . . Interrupt request line

compatible computer)

Abbreviations 71

ISA . . . . . . . Industry Standard Architecture

KB . . . . . . . . Kilobytes

kg . . . . . . . . . Kilograms

LAN. . . . . . . Local-area network

lb.. . . . . . . . . Pounds

LBA . . . . . . . Logical block addressing

LCD. . . . . . . Liquid-crystal display

m . . . . . . . . . Meters

mA. . . . . . . . Milliampere

mAhr. . . . . . Milliampere hour

MB. . . . . . . . Megabyte

mm . . . . . . . millimeter

MPEG . . . . . Motion Picture Experts Group

MPU . . . . . . Microprocessor unit

ms . . . . . . . . Millisecond

PDF . . . . . . . Portable document format

PC . . . . . . . . Personal computer

PCI . . . . . . . Peripheral component interconnect

PCMCIA. . . Personal Computer Memory Card International Association

POST. . . . . . Power-on self-test

PNP . . . . . . . Plug and play

PS/2 . . . . . . . Personal System/2

RAM . . . . . . Random-access memory

ROM . . . . . . Read-only memory

SVGA . . . . . Super video graphics array

TFT . . . . . . . Thin-film transistor

USB . . . . . . . Universal serial bus

V . . . . . . . . . Volt

VAC . . . . . . Voltage alternating current

VCC . . . . . . Voltage collector current

VDC . . . . . . Voltage direct current

whr . . . . . . . Watt hour

72 Users Manual

Glossary

AC adapter

The AC (or alternating current) adapter regulates current coming into your
computer from the wall outlet. The current at the wall outlet is alternating current
and needs to be changed by the adapter to DC (direct current) before your
computer can use it for power.

ACPI

ACPI (Advanced Configuration and Power Interface)- a method for describing
hardware interfaces in terms abstract enough to allow flexible and innovative
hardware implementations and concrete enough to allow shrink-wrap OS code to
use such hardware interfaces.

BIOS

BIOS stands for basic input/output system. The BIOS is software (often called
firmware) that is independent of any operating system. It enables the computer to
communicate with the screen, keyboard, and other peripheral devices without
using programs on the hard disk.
The BIOS on your computer is flash BIOS, which means that it has been recorded
on a flash memory chip that can be updated if needed.

Boot

To start your computer. A cold boot resets the entire computer and runs through
all computer self-tests. A warm boot clears out computer memory only.

Boot disk

A disk containing operating system programs required to start your computer. A
boot disk can be a floppy disk, hard drive, or compact disc.

Byte

The basic unit of measure for computer memory. A character—such as a letter of
the alphabet—uses one byte of memory. Computer memory is often measured in
kilobytes (1,024 bytes) or megabytes (1,048,576 bytes).
Each byte is made up of eight bits. For more information on bytes and bits, see an
introductory book on computers.

Cache memory

Cache is very fast, zero-wait-state memory located between the microprocessor
and main memory. Cache reduces the average time required by the
microprocessor to get the data it needs from the main memory by storing recently
accessed data in the cache.

Glossary 73

CardBus

CardBus technology enables the computer to use 32-bit PC Cards. Hardware in
the computer and the Windows operating system provide support for the 32-bit
cards. The voltage of 32-bit cards (3.3 volts) is lower than that of 16-bit cards (5
volts). The 32-bit cards can transmit more data at a time than the 16-bit cards, thus
increasing their speed.

CMOS memory

CMOS (complementary metal oxide semiconductor) memory is powered by the
CMOS battery. The System Setup settings and other parameters are maintained in
CMOS memory. Even when you turn your computer off, the information in
CMOS memory is saved.

COM port

COM stands for communication. COM ports are the serial ports in your computer.

Compact Disc

A compact disc (CD).

Conventional memory

The first 640 KB of system memory. Operating systems and application programs
can directly access this memory without using memory-management software.

Disk

The device used by the computer to store and retrieve information. Disk can refer
to a floppy disk, hard disk, or RAM disk.

Disk cache

A software device that accumulates copies of recently used disk sectors in RAM.
The application program can then read these copies without accessing the disk.
This, in turn, speeds up the performance of the application.
A cache is a buffer for transferring disk sectors in and out of RAM. Data stored in
a disk cache is a copy of data already stored on the physical disk.

DMA (direct memory access)

A method of transferring data from a device to memory without having the data
pass through the microprocessor. Using DMA can speed up system performance.

DPMS

Display Power Management Signalling. Displays or monitors that comply with
this can be managed by the Power Management features found in the system
setup.

Floppy disk

A removable disk, also called floppy or diskette.

74 Users Manual

Hard drive

Also called fixed disk. A hard drive is connected to the computer and can be
installed or removed. Data written to a hard drive remains until it is overwritten
or corrupted.
The 2.5-inch hard drive in your computer was designed for use in a notebook
computer. Because hard drives in notebook computers are smaller than those in
desktop computers, their maximum storage capacity may be less than that of
desktop hard drives. However, because of their smaller size, the drives handle
shock and vibration better than larger drives, which is important for a notebook
computer.

I/O

Input/output. Refers to peripheral devices, such as printers, that are addressed
through an I/O address.

I/O address

I/O stands for input/output. Peripheral devices, such as printers, are addressed
through the I/O port address.

IRQ (interrupt request line)

The IRQ is a hardware line that a device uses to signal the microprocessor when
the device needs the microprocessor’s services. The number of IRQs is limited by
industry standards.

LCD (liquid-crystal display)

The LCD screen on your computer differs from the display screen of a desktop
monitor. Most desktop monitors use CRT (cathode-ray tube) displays, which
work by moving an electron beam across phosphor dots on the back of the screen.
The phosphor dots light up to show the image. LCDs use a liquid-crystal solution
between two sheets of polarizing material. Electric current passing through the
liquid aligns the crystals so that light can or cannot pass through them, creating an
image.

MB (megabyte)

1,024 kilobytes.

Megabit

1,048,576 bits or about 128 kilobytes.

Operating system

A program that supervises the computer's operation, including handling I/O.
Application programs and users can request operating-system services. A user
might request operation-system services to copy files or format a disk. An
application program might use the operating system to obtain keyboard input,
write data to a file, or write data to a screen.

Glossary 75

PC Card

PC Card stands for personal computer card. The Personal Computer Memory
Card International Association (PCMCIA) defines the standards used to develop
all PC Cards. PC Card types include: modems, Ethernet adapters, SCSI adapters,
ATA cards, and memory cards.

PC slot

The PC slot is the hardware slot in the computer where the PC Card is placed.

Pixel

A pixel is an individual dot in a graphic displayed on your computer. The pixels
are so close together that they look as though they are connected. An LCD screen
displays thousands or millions of pixels.

Plug and Play

A plug and play operating system automatically configures computer components
to work with your system. With this type of operating system, you normally do
not need to set jumpers on devices or set memory addresses or IRQs.

RAM (random access memory)

The computer's system memory, including conventional and extended memory.
You can write to and read from RAM. Information stored in RAM is temporary,
and is erased when the system is turned off.

Refresh rate

The refresh rate is the rate at which the image on the LCD screen is rewritten to
the screen. A fast refresh rate helps keep the image from flickering.

Resolution

The resolution is the sharpness or clarity of the image on your LCD screen.
Resolution is measured by the number of pixels the computer’s screen can
display. For example, a resolution of 800 x 600 means that the screen can display
800 pixels in row and can display 600 rows. The more pixels displayed, the higher
the resolution and the better the image.

ROM (read-only memory)

Permanent computer memory dedicated to a particular function. For example, the
instructions for starting the computer when you first turn on power are contained
in ROM. You cannot write to ROM. (ROM is not the same as RAM).

Sector

Also known as disk sector. The portion of a track that is numbered and can hold
a specified number of characters (usually 512 KB).

76 Users Manual

Shadow RAM

A write-protected area of RAM that contains a copy of the BIOS. As the computer
boots, the BIOS is copied from its permanent location in ROM to RAM. The
BIOS can be executed much faster in RAM than in ROM. The BIOS remains in
shadow RAM until you turn off the computer.

TFT (thin film transistor) LCD

A TFT LCD uses a separate transistor circuit to control each pixel. This
technology provides the best resolution for an LCD screen. A TFT LCD is also
sometimes called an active matrix LCD.

Zoomed video

Zoomed video technology enables zoom video PC Card to transfer data directly
from the card to video and audio systems without going through the
microprocessor. This process improves video performance. Video conferencing
and real-time multimedia devices, such as video cameras, are supported by zoom
video.

Glossary 77