Samsung nc10 Service Manual
3-1
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10
3. Disassembly and Reassembly
3-1. NC10 Disassembly and assembly
Part Picture Description
Main
System
1
2
1
1. Before disassembling the system, the AC adapter and the
battery have to be separated.
2. As shown in picture 1, adhere KNOB to the end closely
into the arrow direction, then push the battery up as shown
in picture 2.
3. When the battery is pushed upwards, it can be separated.
4. Remove the BOTTOM screw.
IF only keboard is disassembled, remove only 3 BOTTOM
screws(ㅁ mark).
M2 x L8, Silver (15EA)
5. Remove the DOOR-MEMORY.
[Caution] Attention to red sentence.
Winchester_NC10_Eng.indb 1 2008-09-20 오후 1:36:02
3-2
3. Disassembly and Reassembly
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10
Part Picture Description
Main
System
6. Remove the memory by pushing the xed-tap out.
7. Push the Hook up inwards by using a pin-set as shown in
the picture, and then lift the key board up.
[Notice]
When you push the hook up, you have to be careful not to
scratch Topdp.
As shown in the picture, lift the top side of keyboard up and
then disassemble keyboard.
8. Lift the Keyboard up, and then take the FPC out after
lifting the Connector Lock.
Take Keyboard FPC cable out after opening Keyboard
connector Lock.
Winchester_NC10_Eng.indb 2 2008-09-20 오후 1:36:13
3-3
3. Disassembly and Reassembly
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10
Part Picture Description
Main
System
9. As shown in the picture, separate the BOTTOM-
COVER(LAN Connector side rst) by widening the gap
between the BOTTOM-COVER and the TOP. (Be careful
not to make scratch in the gap using a wooden-driver.)
As shown in the picture, separate the BOTTOM-COVER
by widening the gap between the BOTTOM-COVER and
the TOP. (Be careful not to make scratch in the gap using a
wooden-driver.)
10. After removing the Screw for xing HDD remove the
INSULATOR by lifting the HDD up to about 70 degrees
direction.
[Notice]
When you life the HDD up, you shall not enforce excessive
strength.
11. Speaker CONN. INT Mic CONN., Power S/W CONN.
Touch-Pad FPC.
Winchester_NC10_Eng.indb 3 2008-09-20 오후 1:36:22
3-4
3. Disassembly and Reassembly
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10
Part Picture Description
Main
System
12. Remove the Antenna Cable which is connected with
wireless LAN, and then remove the Screw which xes
WLAN. [Aux(Black)]
M2 x L4, Black (1EA)
1. White, Main
2. Black, Aux
13. Remove the Bluetooth Camera Cable and the LCD cable
CONN. and disassemble the W/L Antenna Cable.
14. Remove the Screw which xes the Main Board and the
TOP and then separate Main Board from TOP.
M2 x L4, Black (2EA)
15. Remove the both sides of Screw, which fasten the Hinge
and the TOP.
M2 x L4, Black (4EA)
16. Stand the Top Ass’y in a vertical direction.
Winchester_NC10_Eng.indb 4 2008-09-20 오후 1:36:32
Loading...