Samsung NA30N7755TS Installation manual

Gas Cooktop

Installation manual

NA30N6555T*/NA30N7755T* NA36N6555T*/NA36N7755T*

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 1 5/28/2018 12:50:28 PM

WARNING: If the information in this manual is not followed exactly, a re or explosion may result causing property damage, personal injury or death.

• DO NOT store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS:

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch.

- DO NOT use any phone in your building.

- Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the re department.

• Installation and service must be performed by a qualied installer, service agency, or the gas supplier.

Contents

Before you begin 3

Important safety information 3

Gas cooktop components 8

What’s in the box 8

Installation requirements 10

Pre-installation checklist 10 Location requirements 10 Gas supply requirements 12 Special gas requirements (gas models sold in Massachusetts) 13 Electrical requirements 13

Installation instructions 14

Installing your gas cooktop 14 Step 1. Unpack the cooktop 14 Step 2. Installing the cooktop. 14 Step 3. Connect the cooktop to gas supply 16 Step 4. Check for gas leaks. 17 Step 5. Electrical connections. 18 Step 6. Assemble the cooktop burners. 18 Step 7. Check the ignition of cooktop burners 20 Step 8. Checking the ame quality. 20 Step 9. Install the grates. 21 Step 10. Final installation checklist 22 LP (Propane) conversion instruction 22 Supplied parts 23 Converting the pressure regulator 24 Converting the cooktop burners 25 Adjusting low ame setting on cooktop burners 26

2 English

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 2 5/28/2018 12:50:28 PM

Before you begin

Important safety information

About this manual

READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY.

Important note to the installer

• Read all instructions contained in these installation instructions before installing the cooktop.

• Remove all packing materials from the cooktop compartments before connecting the electric and gas supply to the cooktop.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the consumer.

• Installation of this appliance requires basic mechanical skills.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

Important note to the consumer

Keep these instructions with your user manual for future reference.

• As when using any appliance generating heat, there are certain safety precautions you should follow.

• Be sure your cooktop is installed and grounded properly by a qualied installer or service technician.

• Make sure the wall coverings around the cooktop can withstand the heat generated by the cooktop.

• Cabinet storage space above the cooktop burners should be a minimum of 30 in (76.2 cm).

Important note to the servicer

The electrical diagram is attached inside the burner box.

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE

• All electrical and gas equipment with moving parts can be dangerous. Please read the important safety instructions for this appliance in this manual. The instructions must be followed to minimize the risk of injury, death, or property damage.

• Save this manual. Please Do Not Discard.

Symbols used in this manual

WARNING

Hazards or unsafe practices that may result in severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in electric shock, personal injury, or property damage.

NOTE

Useful tips and instructions. These warning icons and symbols are here to prevent injury to you and others.

Please follow them explicitly. After reading this section, keep it in a safe place for future reference.

Before you begin

English 3

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 3 5/28/2018 12:50:28 PM

Important safety information

WARNING

Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Commonwealth of Massachusetts

Important safety information

• This product must be installed by a licensed plumber or gas tter qualied or licensed by the State of Massachusetts. When using ball-type gas shut-off valves, you must use the T-handle type. Multiple exible gas lines must not be connected in series.

General safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.

• Make sure the hold down brackets are properly installed on the cooktop. See the installation instructions for more information.

• Do not let children near, in, or on the cooktop. Do not let children play with the cooktop or any part(s) of the cooktop. Do not leave children unattended in an area where the cooktop is in use.

• Remove all packaging materials from the cooktop before operating to prevent ignition of these materials. Keep all packaging materials out of children’s reach. Properly dispose the packaging materials after the cooktop is unpacked.

• Do not store any object of interest to children on the cooktop or backguard of the cooktop. Children climbing on the cooktop to reach items could be killed or seriously injured.

• Do not operate the cooktop if the cooktop or any part of the cooktop is damaged, malfunctioning, or missing parts.

• Do not touch any part of the cooktop, including but not limited to, cooktop burners, during or immediately after cooking.

• Know the location of the gas shut-off valve and how to shut it off.

• Do not use the cooktop as a space heater. This cooktop is to be used for cooking purposes only.

• Use only dry pot holders.

• Do not use the cooktop to heat unopened food containers.

• Unplug or disconnect power before servicing.

Fire safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.

• Do not store, place, or use ammable or combustible materials such as paper, plastic, pot holders, linens, curtains, gasoline or other ammable vapors or liquids near the cooktop.

• Do not wear loose tting or hanging garments while using the cooktop.

• To avoid grease buildup, regularly clean the vents.

• Do not let pot holders or other ammable materials touch a heating element. Do

not use a towel or other bulky cloths in place of a pot holder.

• Do not use water on a grease re. To put out a grease re, turn off the heat source and smother the re with a tight-tting lid or use a multipurpose dry chemical or foam-type re extinguisher.

• Do not heat unopened food containers - buildup of pressure may cause container to burst and result in injury.

4 English

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 4 5/28/2018 12:50:29 PM

Gas safety

Electrical and grounding safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.

If you smell gas:

• Close the valve and do not use the cooktop.

• Do not light a match, candle, or cigarette.

• Do not turn on any gas or electric appliances.

• Do not touch any electrical switches or plug a

power cord into an outlet.

• Do not use any phone in your building.

• Evacuate the room, building, or area of all

occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

Checking for gas leaks

• Leak testing of the appliance shall be conducted according to the manufacturer’s

instructions. Do not use a ame to check for gas leaks. Use a brush to spread a soapy water mixture around the area you are checking. If there is a gas leak, you will see small bubbles in the soapy water mixture at the leak point.

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.

• Plug into a grounded 3-prong outlet.

• Do not remove the ground prong.

• Do not use an adapter or an extension cord.

• Do not use a damaged power plug, power cord,

or loose power outlet.

• Do not modify the power plug, power cord, or power outlet in any way.

• Do not put a fuse in a neutral or ground circuit.

• Use a dedicated 120-volt, 60-Hz, 20-amp, AC, fused electrical circuit for this

cooktop. A time-delay fuse or circuit breaker is recommended. Do not plug more than one appliance into this circuit.

• Do not connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.

• This cooktop must be Earth grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path for the electric current. This cooktop is equipped with a cord having a grounding plug. The plug must be rmly plugged into an outlet that is properly installed and grounded in accordance with the local codes and ordinances. If you are unsure whether your electrical outlet is properly grounded, have it checked by a licensed electrician.

• The cooktop is supplied with a 3-pronged grounded plug. This cord must be plugged into a mating, grounded 3-prong outlet that meets all local codes and ordinances. If codes permit the use of a separate ground wire, we recommend that a qualied electrician determine the proper path for this ground wire.

• Electrical service to the cooktop must conform to local codes. Barring local codes, it should meet the latest ANSI/NFPA No. 70 – Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 – Latest Revisions.

• It is the personal responsibility of the cooktop owner to provide the correct electrical service for this cooktop.

Important safety information

English 5

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 5 5/28/2018 12:50:30 PM

Important safety information

Installation safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

Important safety information

following precautions.

• Have your cooktop installed and properly grounded by a qualied installer, in accordance with the installation instructions. Any adjustment and service should be performed only by qualied gas cooktop installers or service technicians.

• Do not attempt to service, modify, or replace your cooktop or any part of your cooktop unless it is specically recommended in this manual. All other service should be referred to a qualied technician.

• Always use new exible connectors when installing a gas appliance. Do not use old exible connectors.

• Make sure the hold down brackets are properly installed on the cooktop. See the installation instructions for more information.

• Remove all tape and packaging materials.

• Remove all accessories from the cooktop. Grates and griddles are heavy. Use

caution when handling them.

• Make sure no parts came loose during shipping.

• Make sure your cooktop is correctly installed and adjusted by a qualied

service technician or installer for the type of gas (natural or LP) you will use. For your cooktop to utilize LP gas, the installer must replace the 5 cooktop burner orices with the provided LP orice set, and reverse the GPR adapter. These adjustments must be made by a qualied service technician in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. The qualied agency performing this work assumes the gas conversion responsibility.

• Installation of this cooktop must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA.54, latest edition. In Canada, installation must conform with the current Natural Gas Installation Code, CAN/CGA-B149.1, or the current Propane Installation Code, CAN/CGA-B149.2, and with local codes where applicable. This cooktop has been design-certied by ETL according to ANSI Z21.1, latest edition, and Canadian Gas Association according to CAN/CGA-1.1, latest edition.

6 English

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 6 5/28/2018 12:50:30 PM

Location safety

Cooktop safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.

• This cooktop is for indoor, household use only. Do not install the cooktop in areas exposed to

the weather and/or water.

• Do not install the cooktop in a place which is exposed to a strong draft.

• Select a location where a grounded, 3- prong outlet is easily accessible.

• If the cooktop is located near a window, do not hang long curtains or paper

blinds on that window.

• For the cooktop to ventilate properly, there is enough clearance at the top, back, sides, and underneath the cooktop. The vents allow the necessary exhaust for the cooktop to operate properly with correct combustion.

• Make sure the wall coverings around the cooktop can withstand heat up to 194 °F (90 °C) generated by the cooktop.

• Cabinet storage above the surface of the cooktop should be avoided. If cabinet storage above the cooktop is necessary: allow a minimum clearance of 30 inches (76.2 cm) between the cooking surface and the bottom of cabinets.

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.

• Make sure all burners are off when not in use.

• Do not use aluminium foil to line the grates or

any part of the cooktop.

• Do not leave burners unattended on medium or high heat settings.

• Before igniting, make sure all burner caps are properly in place and all burners are level.

• Always use the LITE position when igniting the burners and make sure the burners have ignited. If ignition fails, turn the knob to OFF and wait until the gas has dissipated.

• When you set a burner to simmer, do not turn the knob quickly. Make sure the ame stays on.

• Do not place any objects other than cookware on the cooktop.

• This cooktop is designed to cook with a wok or wok ring attachment. If foods are

amed, they should only be amed under a ventilation hood that is on.

• Before removing or changing cookware, turn off the burners.

• Remove food and cookware immediately after cooking.

• Before removing any parts of the burner for cleaning, make sure the cooktop is

off and completely cool.

• After cleaning the burner spreader, make sure it is completely dry before re- assembling.

• To avoid carbon monoxide poisoning, do not pour water into the cooktop well while cleaning.

• Select cookware that is designed for top-cooktop cooking. Use cookware that is large enough to cover the burner grates. Adjust the burner ames so that the ames do not extend beyond the bottom of the cookware.

• To avoid cookware discoloration, deformity, and/or carbon monoxide poisoning, do not use cookware that is exceedingly larger than the grate.

• Make sure cookware handles are turned to the side or rear of the cooktop, but

not over other cooktop burners.

Important safety information

English 7

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 7 5/28/2018 12:50:31 PM

Important safety information

Gas cooktop components

• Stand away from the cooktop while frying.

• Always heat frying oils slowly, and watch as they heat. If you are frying foods at

high heat, carefully watch during the cooking process. If a combination of fats or oils is to be used during frying, mix them together before heating.

• Use a deep-fryer thermometer whenever possible. This prevents overheating the fryer beyond the smoking point.

• Use a minimum amount of oil when shallow pan-frying or deep-frying. Avoid cooking unthawed food or food with excessive amounts of ice.

• Before moving cookware full of fats or oils, make sure it has completely cooled.

• To prevent delayed eruptive boiling, always allow heated liquids to stand at least

20 seconds after you have turned off the burner so that the temperature in the liquid can stabilize. In the event of scalding, follow these rst aid instructions:

Gas cooktop components

1. Immerse the scaled area in cool or lukewarm water for at least 10

minutes.

2. Do not apply any creams, oils, or lotions.

3. Cover with a clean, dry cloth.

What’s in the box

Parts supplied

Cooktop burner grates (3) * Cooktop burners and

caps (5) *

Cast-iron griddle (1) *

(NA30N7755T*/

NA36N7755T*)

Regulator (1) * Hold down brackets (2) * Cover (1)

Foam tape

Wok grate (1) *

(NA30N7755T*/

NA36N7755T*)

Aluminum griddle (1) *

(M4L10 2 ea, M4 L16 2 ea,

(NA30N6555T*/

NA36N6555T*)

Screw (6)

W3/16 L75 2 ea)

• Make sure you have received all of the supplied parts shown above.

• If your cooktop was damaged during shipping or you do not have all of the

supplied parts, contact your local retailer.

NOTE

If you need an accessory marked with an * (asterisk), please contact the Samsung Call Center using the phone number listed on the last page of this manual or visit our on-line parts web site at www.samsungparts.com.

8 English

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 8 5/28/2018 12:50:32 PM

Parts needed

Tools needed

Gas line shut-off

valve

135-degree elbow

(optional)

Flexible metal

appliance connector

½ in (ID) x 5 ft

90-degree elbow

(optional)

Flare union adapter ¾ in or ½ in (NPT) x

½ in (ID)

Flare union adapter

½ in (NPT) x ½ in

(ID)

Flat-blade

screwdriver

Phillips screwdriver Open-end or

adjustable wrench

¼" Nut driver Pencil and ruler Level

Utility knife Soapy water

Pliers Saber saw

solution

Pipe wrench (2)

Pipe joint compound

Gas cooktop components

English 9

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 9 5/28/2018 12:50:34 PM

Installation requirements

Pre-installation checklist

1. When preparing cooktop opening, make sure the inside of the cabinet, and the

cooktop do not interfere with each other.

2. Remove packing materials, grate boxes, regulator with literature, and literature

package from the cooktop before beginning installation.

Location requirements

BEFORE YOU BEGIN to install this appliance, refer to the following information, dimensions, and clearances. These dimensions must be met for safe use of the cooktop. The location of the electrical outlet and gas piping may be adjusted to meet the following dimensions and clearances.

CAUTION

This cooktop has been designed to comply with the maximum allowable wood cabinet temperature of 194 °F (90 °C). Make sure the wall covering, countertops, and cabinets around the cooktop can withstand the heat (up to 194 °F [90 °C]) generated by the cooktop. If not, discoloration, delamination, or melting may occur.

Installation requirements

Maintain the following minimum clearance dimensions

13” MAX. (330 mm)

27/8” MIN

(73.0 mm)

30” - NA30N6555T*/ NA30N7755T* 36” - NA36N6555T*/ NA36N7755T*

30” MIN

(762 mm)

12” MIN

(304.8 mm)

18” MIN

(457 mm)

(304.8 mm)

12” MIN

13” MAX.

(330 mm)

33/8” Min

(85.7 mm)

30” MIN

(762 mm)

12”

(304.8 mm)

18” MIN

(457 mm)

12”

(304.8 mm)

NOTE

All horizontal clearances must be maintained for a minimum of 18” (457 mm) above the cooking surface.

39/16”

(90.5 mm)

/16”

(11.1 mm)

DRAWER

NOTE

Allow 7/16” minimum vertical clearance from the cooktop bottom (or 39/16”) minimum depth from the countertop) to any combustible surfaces, including the upper edge or a drawer installed below the cooktop.

Electrical outlet 12” (30.5 cm) minimum

below countertop

Installation over built-in oven

See built-in oven installation for complete installation instructions.

5” To Center of 2” Dia. Hole From Countertop

90° Elbow

Cabinet Sides

2” Dia. Hole

(20

/8” from front

of countertop to

hole Center

View from Front of Cooktop

10 English

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 10 5/28/2018 12:50:35 PM

Overall cooktop dimensions

24/9” (62 mm) countertop to

grate surface

31/8” (79.3 mm)

chassis eight

Model A B C

NA30N6555T* NA30N7755T*

(762 mm) NA36N6555T* NA36N7755T*

(914.4 mm)

Cutout dimensions of countertop

30”

36”

Installation dimensions with downdraft hood

NOTE

• Make sure the clearance dimensions when you install the cooktop with downdraft hood.

• The cooktop can be installed after detaching Smart Connect module. Please refer to the instruction how to detach Smart Connect module on page 15.

/7” (40 mm) Min.

221/3” (568 mm)

21” (533 mm)

281/7”

(715 mm)

332/3”

(855 mm)

193/8”

(492.1 mm)

186/7”

(479 mm)

/7” (40 mm) Min.

Downdraft Hood

1 Cooktop frame to downdraft hood

Smart Connect Module

Cooktop

(H) Cutout to downdraft hood

Installation requirements

surface

Rear wall

(85.7 mm)

27/8”

(73 mm)

33/8”

Minimum distance to combustible side wall above countertop (both sides)

195/8”

(498.5 mm)

191/8”

(485.8 mm)

281/2”

(723.9 mm)

337/8”

(860.4 mm)

Smart Connect

Module

Model (H) Min.

NA30N6555T* NA30N7755T* NA36N6555T* NA36N7755T*

24/9” (62 mm)

3” (76 mm)

12”

(304.8 mm)

12”

(304.8 mm)

Vertical

combustible

Model (D) Min. (E) Min. (F) Min. (G) Min.

NA30N6555T* NA30N7755T*

NA36N6555T* NA36N7755T*

English 11

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 11 5/28/2018 12:50:35 PM

Installation requirements

Single Oven Under counter

B 4” (10.1 cm)

Installation requirements

C Min. 281/2”/ Max. 285/8” (Min. 72.4 cm / Max. 72.7 cm)

D Min. 1”/ Max. 11/4” (Min. 2.5 cm / Max. 3.2 cm)

E Min. 271/4”/ Max. 271/3” (Min. 69.2 cm / Max. 69.5 cm)

F 24” (61 cm)

G Min. 22” (Min 55.9 cm)

H Max. 91/2” (Max. 24.1 cm) – Junction Box

Utility locations and dimensions

01 This cooktop can be installed above any

Samsung single built-in oven. Refer to installation manual of oven.

02 Gas and Electrical Connections for Gas

Front of unit

Front of cooktop

Cooktop Must be Located in an Adjacent Accessible Location to the Right.

Power cord 393/8”

(100.0 cm) long

/8”-18 NPT male

gas inlet

* Gas inlet protrudes 14/7 (4.0 cm)

Chassis

130/31” (5.0 cm)

from bottom.

11/4” (3.2 cm)

Size

Min. 33/4” (9.5 cm)

Gas supply requirements

Provide adequate gas supply

This cooktop is designed to operate at a pressure of 5 in (13 cm) of water column on natural gas or 10 in (25 cm) of water column on LP gas (propane or butane).

Make sure you are supplying your cooktop with the type of gas for which it is designed. Do not attempt to convert the appliance from the gas specied in this

manual to a different gas without consulting the gas supplier.

This cooktop is convertible for use on natural or propane gas. If you decide to use this cooktop on LP gas, conversion must be made by a qualied LP installer before attempting to operate the cooktop.

For proper operation, the pressure of natural gas supplied to the regulator must be between 5 in and 13 in (13 cm and 33 cm) of water column.

For LP gas, the pressure supplied must be between 10 in and 13 in (25 cm and 33 cm) of water column.

When checking for proper operation of the regulator, the inlet pressure must be at least 1 in (2.5 cm) greater than the operating (manifold) pressure as given.

12 English

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 12 5/28/2018 12:50:36 PM

The pressure regulator located at the inlet of the cooktop manifold must remain in the supply line regardless of whether natural or LP gas is being used.

NOTE

• The cooktop comes from the factory with a regulator in the shipping carton. Use only the regulator provided. The regulator must be installed in the gas line that runs from the cooktop gas inlet to the gas shut off valve.

• An external manual shut-off valve must be installed between the gas inlet and the cooktop for the purpose of turning on or shutting off gas to the appliance.

• Be sure the connectors are installed when you need coupling by a qualied installer.

• Never reuse old connectors when installing the cooktop. The use of old connectors can cause gas leaks and personal injury. Always use new exible connectors when installing a gas appliance.

Special gas requirements (gas models sold in Massachusetts)

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS:

WARNING

Gas leaks may occur in your system, creating a dangerous situation. – Gas leaks may not be detected by smell alone. – Gas suppliers recommend you purchase and install a UL-approved gas detector.

Gas detector should be installed in accordance with the manufacturers instructions.

• Cooktop must be installed by a qualied plumber or gas tter by the State of Massachusetts.

• A T-handle manual gas valve MUST be installed in the gas supply line to your cooktop.

• If a exible gas connector is used to install your cooktop, multiple exible gas lines must not be connected in series.

Electrical requirements

WARNING

• It is the owner’s responsibility to make sure that the electrical service meets electrical requirements and that he electrical outlet has been properly installed by a licensed electrician.

• To reduce the risk of re, electric shock, or personal injury:

All cooktops

• Do not use an extension cord or adapter plug with this cooktop.

• This cooktop must be properly grounded.

• Check with a qualied electrician if you are in doubt as to whether your cooktop

is properly grounded.

• Do not modify the plug provided with your cooktop — if it doesn’t t the outlet, have a proper outlet installed by a qualied electrician.

• All wiring and grounding must be done in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA No. 70 – Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 – Latest Revisions and local codes and ordinances.

• Wiring diagram is located on the inside of the burner box.

• This cooktop is equipped with an electronic ignition system that will not operate

if plugged into an outlet that is not properly polarized.

Gas cooktops

• All gas models are equipped with a power cord with an equipment-grounding conductor and a grounding plug.

• A 120-Volt, 60-Hz, AC, approved electrical service with 20-amp circuit breaker or time-delay fuse is required for all U.S. and Canadian models.

Installation requirements

English 13

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 13 5/28/2018 12:50:36 PM

Installation instructions

Grounding

• All cooktops must be grounded for personal safety.

• The plug must be rmly plugged into a three-prong outlet that is properly

installed and grounded in accordance with all local codes and ordinances. In the event of a malfunction or breakdown, grounding will decrease the risk of electrical shock by providing a path for the electric current.

• Do not use a damaged power plug or loose wall outlet.

• Do not use an extension cord or adapter with this appliance

• Do not, under any circumstances, cut, modify, remove, or otherwise defeat the

grounding (third) prong from the power cord. If the plug and the outlet do not match or you have any doubt, have a qualied electrician install the proper outlet. The customer should have the wall receptacle and circuit checked by a qualied electrician to make sure the receptacle is properly grounded.

• NEVER connect ground wire to plastic plumbing lines, gas lines, or water pipes.

CAUTION

Failure to follow these instructions can result in death, re, or electrical shock.

Additional installation requirements for mobile homes

The installation of appliances designed for mobile home installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or, when such standard is not applicable, the Standard for Manufactured Home Installations, latest edition (Manufactured Home Sites,

Installation instructions

Communities and Set-Ups), ANSI A225.1, latest edition, or with local codes. In Canada, mobile home installation must be in accordance with the current CAN/CSA Z240/MH Mobile Home Installation Code.

Installing your gas cooktop

IMPORTANT:

Please read the following instructions, as well as the Important Safety Instructions section at the front of this manual, completely and carefully BEFORE installing and/or operating the gas cooktop. Improper installation, adjustment, service, or maintenance can cause personal injury or property damage.

NOTE

To ensure proper installation, we strongly recommend that you hire a professional installer.

Step 1. Unpack the cooktop

Remove all packaging materials. Failure to remove packaging materials could result in damage to the appliance.

Inventory all loose parts against the Parts supplied components listed on page 8. Check for shipping damage and/or missing parts. Any damage and/or missing

parts should be reported to your local retailer.

Step 2. Installing the cooktop.

Rubber

Smart Connect module

Smart Connect

module

CAUTION

• When inserting the cooktop into the cutout opening, do not remove the rubber piece protecting Smart Connect module. Protecting rubber piece should be removed after carefully inserting the cooktop.

• When mounting the cooktop, make sure to insert the cooktop with the front side rst. Inserting from the rear may damage the Wi-Fi module.

14 English

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 14 5/28/2018 12:50:36 PM

Correct installation

Front of unit

Hold down

bracket holes

1. Locate electrical outlet and gas shut-off valve beneath cabinet.

2. Apply the foam tape around the edge of the cutout opening. Do not overlap the foam strips.

• The foam strip helps avoid damage to the underside of the cooktop from debris and helps the cooktop sit at on uneven counters.

3. Protect surface of cooktop

• Place a towel or tablecloth onto the countertop.

4. With bottom side rst, gently put the cooktop down. Then, slightly lift up the rear to remove the protective rubber for the Wi-Fi module.

• Make sure the front of the countertop is parallel to the cooktop

• Make nal check that all required clearances are met.

5. Secure the cooktop to the countertop using the two provided hold-down brackets as shown.

Hold down bracket install guide

Case 1.

Chassis

M4 L10 screw

M4 L16 screw

Countertop

Side wall of

undercounter

cabinet

Hold down

bracket

Case 2.

Countertop

Chassis

Hold down

bracket

M4 L10 screw

W3/16 L75 screw

NOTE

Smart Connect module can/must be detached before installation of the cooktop in folowing cases:

• The consumer doesn’t need to Smart connect function.

• Installation is not possible because the Smart Connect module protrudes against

the rear wall of the countertop.

• The downdraft hood is installed and protrudes against the Smart Connect module.

The Cover must be installed in place of Smart connect module if Smart connect module has been removed. Please read following instructions on how to detach Smart connect module.

Installation instructions

Gas inlet

Power cord

Hold Down Bracket Installation

English 15

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 15 5/28/2018 12:50:37 PM

Installation instructions

Smart connect module

Cover

Installation instructions

Top view

Rubber

Insert the wire connector

Wire connector

1. Remove screws from all 5 burner cups and 4 screws from the cooktop frame. Remove the rubber protecting Smart connect module. Pull out all knob dials and lift up to remove the frame cooktop.

2. Detach Smart connect module from case burner. Disconnect wire connector from the PCB.

3. Install supplied cover in place of Smart connect module.

4. Insert the wire connector diagonally into the cover. Make sure it ts rmly.

5. Return all burner cups and cooktop frame to original position, reinstall all knob dials.

Step 3. Connect the cooktop to gas supply

Shut off the main gas supply valve before disconnecting the old cooktop and leave it off until the new hookup has been completed. Don’t forget to relight the burner on other gas appliances when you turn the gas back on.

Because hard piping restricts movement of the cooktop, the use of a CSA International-certied exible metal appliance connector is recommended unless local codes require a hard-piped connection.

WARNING

If the information in this manual is not followed exactly, a re or explosion may result, causing death, personal injury, or property damage.

– Do not store or use gasoline or other ammable vapors and liquids in the

vicinity of this or any other appliance.

– WHAT TO DO IF YOU SMELL GAS:

• DO NOT light a match, candle, or cigarette.

• DO NOT try to light any appliance.

• DO NOT touch any electrical switch.

• DO NOT use any phone in your building.

16 English

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 16 5/28/2018 12:50:38 PM

• Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

– Installation and service must be performed by a qualied installer, service

agency, or gas supplier.

– Do not install the cooktop without also installing the included gas regulator. Do

not use the cooktop without the regulator installed.

– Ensure that the arrow on the regulator points in the direction of the gas ow,

towards the cooktop. – Do not apply excessive pressure when tightening gas connections and ttings. – Test the gas lines for leaks as instructed before use. Do not use a ame to check

for leaks. Never use an old connector when installing a new cooktop. If the hard-piping

method is used, you must carefully align the pipe; the cooktop cannot be moved after the connection is made.

To prevent gas leaks, apply pipe-joint compound or wrap pipe-thread tape with Teon on all male (external) pipe threads.

1. Attach the gas pressure regulator (included with the cooktop) to the cooktop

pipe nipple inlet. For tight installations, the regulator may be installed upstream from the pipe nipple, anywhere between the shut-off valve and the cooktop. For best performance, minimize gas pressure loss by attaching the regulator as close as possible to the cooktop gas inlet.

2. Complete connection of the gas supply to the cooktop by installing a exible

gas line between the pressure regulator and the shut-off valve.

Flexible connector hookup

Installer: Inform the consumer of the location of the gas shut-off valve.

Gas Shut-Off Valve

0.5-in or 0.75-in Gas Pipe

Adapter

Flex Connector (6-ft max.)

Gas Flow into Cooktop

Adapter

Tubing Line

to Cooktop

Control

Manifold

Pressure

Regulator

NOTE

The gas shut-off valve should be installed in an accessible location in the gas piping, external to the appliance, for the purpose of turning on or shutting off the gas to the appliance.

Step 4. Check for gas leaks.

WARNING

To prevent death, personal injury, explosion, and/or re hazard, DO NOT use a ame to check for gas leaks.

When using test pressures greater than ½ psig to pressure-test the gas supply system of the residence, disconnect the cooktop and individual shut-off valve from the gas supply piping. When using test pressures of ½ psig or less to test the gas supply system, simply isolate the cooktop from the gas supply system by closing the individual shut-off valve.

1. When all connections have been made, make sure all cooktop controls are in the off position and turn on the main gas supply valve.

2. Use a liquid leak detector at all joints and connections to check for leaks in the system.

3. Tighten all connections if necessary to prevent gas leakage in the cooktop or supply line.

Installation instructions

English 17

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 17 5/28/2018 12:50:38 PM

Installation instructions

Step 5. Electrical connections.

WARNING

• Disconnect all electrical power of the main circuit breaker or fuse box before installing.

• BEFORE OPERATING OR TESTING, follow the grounding requirements on pages 14 in this manual. Improper connection of the grounding plug can result in a rick of electric shock.

• All gas cooktops come with a power cord. The power cord is connected to the bottom of the cooktop. Please review “Electrical requirements” on pages 13.

• The electrical system, including the power cord, is preinstalled and prewired at the factory. Altering any part of this system may result in a short or overload.

1. Plug in the power cord. Make sure the outlet meets local or national electrical

codes as referenced on pages 13.

2. Check the gas supply line to make sure it did not get damaged and it stayed

connected during positioning.

Installation instructions

Step 6. Assemble the cooktop burners.

CAUTION

• Do not operate the cooktop burners without all burner parts in place.

• Be careful not to push in any cooktop controls while removing the cooktop

burner. A slight electrical shock might result which could cause you to knock over hot cookware.

• Do not remove the top or touch the electrode of any burner while another burner is turned on. Electrical shock might result.

1. Position cooktop burner heads on top of the cooktop burner manifolds as shown on the right. The electrodes will t into the slot in the bottom of the heads. Make sure the cooktop burner heads are at and parallel with the cooktop.

2. Place the matching size caps on top of each cooktop burner head.

Dual Burner head

1. As shown, insert the marked area of

burner head into the matching area of burner cup so that they line up.

18 English

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 18 5/28/2018 12:50:39 PM

Round Burner head

2. Install the burner head so that the

electrode passes through the opening for the electrode. Make sure the burner head lies at on the stove top.

1. Orient the burner head so that the opening for the electrode lines up with the electrode.

2. Install the burner head so that the electrode passes through the opening for the electrode. Make sure the burner head lies at on the stove top.

Burner Cap

Burner cap

1. Match the burner caps to the burners by size, and then re-install the caps on the burner heads.

CAUTION

Make sure each cap is re-installed on the correct burner head, is centered on the burner head, and lies at.

CAUTION

Make sure all burner components (heads and caps) are reinstalled properly. They will be stable and rest at when correctly installed.

Burner Head

CAUTION

Make sure all burner components (heads and caps) are reinstalled properly. They will be stable and rest at when correctly installed.

Top Bottom

NOTE

The precise simmer burner (RR) cap and the inner Dual burner (Center) cap are interchangeable.

English 19

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 19 5/28/2018 12:50:40 PM

Installation instructions

Step 7. Check the ignition of cooktop burners

Check the operation of all cooktop burners after the cooktop has been installed and assembled, gas supply lines have been carefully checked for leaks, and electrical power cord has been plugged in.

NOTE

• If the burner does not light within 4 seconds, turn the knob off and wait one

Installation instructions

minute before trying again.

• When you push in and turn the control knob, all spark igniters will make a series of sparks, but only the burner turned to Lite will light.

To turn on a cooktop burner

1. Push in and turn the control knob for that cooktop burner to the Lite position. The “clicking” sound indicates the electronic ignition system is operating properly. The burner will light in about 4 seconds, after the air has been purged from the supply line .

2. After the burner lights, turn the control knob to the desired setting. The “clicking” sound will stop and the ame height will change from Max. to Min. during turning the control knob.

3. Repeat steps 1 and 2 to check the operation of each cooktop burner in succession.

Step 8. Checking the ame quality.

All combustion ames need to be visually checked to determine their ame quality.

CAUTION

If you attempt to measure the ame, please use caution. Burns could result.

1. Soft blue ames—Normal for natural gas operation.

2. Yellow tips on outer cones—Normal for LP gas operation.

3. Yellow ames—Abnormal for any gas operation; call for service.

NOTE

If burner ame looks like 3, the cooktop should not be used until it is serviced. Call for service. Normal burner ames shall look like 1 or 2, depending on the gas type you use.

20 English

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 20 5/28/2018 12:50:41 PM

Step 9. Install the grates.

NOTE

Install the grates as instructed below for longest life. When installed properly, the openings in the grates are centered over the burners. The three cooktop grates are designed to t in specic positions on the cooktop. For maximum stability, these grates should only be used in their proper positions.

• Please place the grate marked with the letter ‘L’ on the left side, and the one with the letter ‘R’ on the right side.

• The middle grate must be installed with the lled-in section, marked ‘BACK’, oriented towards the back of the cooktop.

The back of the right grate is notched to help you orient the grates correctly. See the illustration below.

To replace the grates correctly, follow these steps:

1. Locate the notch on the back of the right grate.

2. Orient the right grate so that it is on the right side of the cooktop with the

notch in the back.

3. Gently lower the legs of the right grate into the corresponding dimples on the

cooktop.

4. Gently lower the legs of the remaining two grates into the corresponding

dimples on the cooktop as shown in the illustration.

Back of left grate

Back of center grate

Back of right grate

Installation instructions

English 21

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 21 5/28/2018 12:50:41 PM

Installation instructions

Step 10. Final installation checklist

WARNING

• To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked.

• Proper installation is the responsibility of the homeowner. The importance of proper installation of your Samsung cooktop cannot be overemphasized.

You have just completed installing your cooktop. Make sure all control knobs are in the off position. The following is a checklist to conrm your cooktop is safely installed and ready for operation.

– Gas line has been properly connected to the cooktop. The gas has been turned

on.

All connections have been checked for leaks. – The cooktop is plugged into the properly grounded electrical receptacle. – The cooktop burners and grates have been properly assembled. – All burners have been tested for proper operation.

Installation instructions

LP (Propane) conversion instruction

WARNING

• This conversion must be performed by a qualied installer or gas supplier in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. Failure to follow ALL in structions could result in serious injury or property damage. The qualied agency performing this work assumes responsibility for the conversion.

• Know the location of the gas shut-off valve and how to shut it off if necessary.

• Unplug or disconnect power before servicing.

• Do not operate the cooktop burners when using LP gas before converting the

pressure regulator and burner orices for LP gas use. Failure to do so could cause high ames and toxic fumes which can result in serious injury.

• Do not mix up or substitute LP gas burner orices during conversion process. Improper orice placement will effect burner and cooking performance and could result in personal injury and/or product damage.

All Samsung gas cooktops are manufactured and shipped to be used with natural gas. The cooktop are also shipped with LP Conversion Kits, so the cooktop can be converted to be used with LP gas. The kits consist of a set of properly-sized burner orices to be used in the cooktop burners. These orices will be positioned in a sheet of cardboard and placed in a plastic bag. The bag is placed with a user manual. The orice in the pressure regulator is a dual-purpose orice, one side for natural gas and the other for LP gas.

22 English

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 22 5/28/2018 12:50:41 PM

Supplied parts

115

The following parts make up the LP conversion kit:

ORIFICES/ORIFICES/ORIFICIOS

LR(WHT)

LF(WHT

DG69-00399A

DG96-00686A

(ASSY NOZZLE-KIT)

NA30N6555T*/ NA36N6555T* NA30N7755T*/ NA36N7755T*

The all orices’ positions are marked on the provided sheet. The spud in the pressure regulator is factory-installed for Natural Gas (NG) use. LP conversion requires spud removal and reinstallation for LP use.

BURNER ORIFICE SIZES AND OUTPUT RATINGS

Burner Location BTU Rate Orice size [mm]

RF 11,500 1.04

LF 7,500 0.83

RR 4,000 0.62

LR 7,500 0.83

Center

Model NA30N6555T* / NA36N6555T*

Model NA30N7755T* / NA36N7755T*

RR(YEL)

CENTER Out(PUR) In(GRAY)

F(RED)

(LP Gas [Propane] 10 in WCP)

14,500 In: 0.46 / Out: 0.74 (2 pcs)

16,500 In: 0.46 / Out: 0.83 (2 pcs)

LR(WHT)

LF(WHT

DG69-00399B

(ASSY NOZZLE-KIT)

CENTER Out(WHT) In(GRAY)

DG96-00686B

RR(YEL)

F(RED)

BURNER ORIFICE SIZES AND OUTPUT RATINGS

(Natural Gas 5 in WCP)

Burner Location BTU Rate Orice size [mm]

RF 13,000 1.64

LF 9,500 1.40

RR 5,000 1.01

LR 9,500 1.40

Center

Model NA30N6555T* / NA36N6555T*

Model NA30N7755T* / NA36N7755T*

19,000 In: 0.70 / Out: 1.30 (2 pcs)

22,000 In: 0.85 / Out: 1.36 (2 pcs)

NOTE

Orice markings:

115 – Denotes 1.15 mm orice size opening.

Installation instructions

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 23 5/28/2018 12:50:42 PM

English 23

Installation instructions

Required tools

Adjustable wrench

Small at-bladed

precision screwdriver

To convert your for use with LP gas, perform the following steps and procedures:

1. Disconnect electrical power to the cooktop. Unplug the cooktop power cord, trip the circuit breaker, or remove the fuse from the fuse box.

2. Shut off the gas supply to the cooktop. Close the manual shut-off valve to the cooktop.

Installation instructions

/2” open-end wrench Screwdrivers: Phillips

Nut drivers: 9/32” or 7

Converting the pressure regulator

NOTE

If you are using LP gas to fuel the cooktop, the following steps and conversions must be made before the ames can be adjusted.

1. Using your ngers, turn the cap. And carefully look at the spring retainer to locate the NAT or LP position.

NAT

NAT. Position

Gasket

Pressure Regulator

NATCap

NAT

Spring Retainer

L.P./Propane

Position

2. Turn the spring retainer over by rotating it 90 deg., pull it from the cap, turn the

spring retainer over so that LP is showing, insert it back into the cap, and then rotate it 90 deg. Into position.

3. Screw the cap back onto the regulator and tighten.

24 English

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 24 5/28/2018 12:50:43 PM

Converting the cooktop burners

NOTE

If you are using LP gas to fuel the cooktop, the following steps and conversions must be made before the ames can be adjusted.

1. Lift off the cooktop burner caps and the cooktop burner heads from the cooktop burner manifold cups.

NOTE

Save these orices and note their positions for future conversions back to natural gas.

3. Locate the LP conversion orices that were shipped with the cooktop.

4. Identify the proper orice by orice size for each of the cooktop burners.

5. Install the proper orices in each of the burner manifold cups and tighten with

a 9/32” or 7 mm nut driver.

Cap

Burner Head

Burner Cup

Cooktop Burner Locations

2. Using a 9/32” or 7 mm nut driver, remove the burner orice from the bottom of each burner manifold cup.

Cooktop

Burner Orice

NOTE

Any other placement of orices could result in dangerous operating conditions and/or poor cooking results.

6. Set all burner heads on top of the manifold cups in the same location as they were removed. The hole on the side of the burner heads goes over the electrodes. The burner heads are correctly installed when they are at on the top of the manifold cups.

7. Set all burner caps on top of the burner heads. These are also at when they are installed to ensure proper safe operation.

Installation instructions

English 25

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 25 5/28/2018 12:50:43 PM

Installation instructions

Adjusting low ame setting on cooktop burners

All Cooktop burner ames should be checked at their lowest setting. Use the following steps to check and adjust the cooktop burner settings.

NOTES

• Low setting adjustments should always be made with two or more burners operating at the same time.

• Call for service when you need to adjust the inner ame of the cooktop center burner settings.

1. Turn on two or more cooktop burners and set them between MED and HI.

2. Quickly turn one of the control knobs counterclockwise to the lowest setting.

The ame should stay lit. If the ame utters or goes out, adjust the bypass valve on the control valve for that burner.

3. Pull the control knob for that burner straight off.

4. Using a small at-bladed screwdriver, adjust the bypass valve screw in the base

of the valve stem. Turn the bypass valve screw counter clockwise to increase the ame size.

Installation instructions

Value Stem

Flat-bladed

screwdriver

Dual valve

Inner ame bypass screw

Outer ame bypass screw

Combustion ame quality

1. Soft blue ames—Normal for natural gas

operation.

2. Yellow tips on outer cones—Normal for LP gas operation.

3. Yellow ames—Abnormal for any gas operation. Further adjustment required.

Additional low ame check

1. Quickly open and close the cabinet door while the cooktop burner is set on LO.

If the ame is extinguished, increase the low ame setting and repeat the test until the ame is stable.

2. Turn the knob from HI to the lowest setting quickly. If the ame goes out at the lowest setting, increase the low ame setting and repeat the test until the ame is stable.

5. Replace control knob and recheck the low ame setting.

6. Repeat step 1 thru 5 to check and adjust the low ame settings on the

remaining cooktop burners.

26 English

Install_NA30N6555TG_DG68-01091A-01_EN+MES+CFR.indb 26 5/28/2018 12:50:44 PM

+ 58 hidden pages