SAMSUNG MM-N2 Alignment and Adjustments

Page 1
1. Alignment and Adjustments
1-1 Tuner
Samsung Electronics 1-1
FM THD Adjustment
Minimum Distortion (Figure 1-1)
SSG FREQ.
Adjustment point (IT1)
98 MHz
FM DETECTOR COIL
FM Stereo Adjustment
L-CH/R-CH : Maximum(Figure 1-3)
SSG FREQ.
Frequency
Adjustment point (ISVR1)
98MHz
98MHz
SEMI-VR(5KΩ)
FM Search Level Adjustment
Adjust ISVR2 so that “TUNED” of LCD is lighted (Figure 1-2)
Figure1-2 FM Auto Search Level Adjustment
Figure1-3 FM Stereo Separation Adjustment
Figure1-1 IF CENTER and THD Adjustment
SSG FREQ.
Adjustment point
(ISVR2)
98 MHz
BEACON SENSITIVITY SEMI-VR(50KΩ)
FM SSG
FM SSG
75 Dummy
5K
Stereo Modulator (Pilot 10%)
OUT
Oscilloscope
FM antenna
SET
Speaker Terminal
EXT
GND
VTVM
GND
22 dB
FM SSG
Output GND
Speaker Terminal
FM Antenna Terminal
Distortion Meter
Input
SET
Input
output
Oscilloscope
FM IN
FM Antenna
SET
50 k
ISVR1
ISVR2
FM DET
IT1
Page 2
1-2 Samsung Electronics
1-1-1 Test Equipment
1-1-2 Pre-Adjustment
1-1-3 AM Adjustment
1. AM Standard Signal Generator (S.S.G) : 400Hz, 30% MOD
2. Oscilloscope
3. VTVM
4. Frequency counter
5. Loop antenna
6. Dummy load (4Ω)
7. DC voltmeter
1. Check the source voltage
2. Press TUNER/BAND to select the AM(MW) function.
3. Set the volume control to mid position.
Intermediate frequency (IF) adjustment
AM frequency coverage adjustment
AM tracking adjustment
Figure 1-4 Connect DC voltmeter to AM VT and GND(OKV1)
1
2
4
5
3
Figure 1-5
Figure 1-5
450 KHz
594 KHz
Figure 1-4
SET
60 cm
AM Signal Generator
Test Loop Antenna
Speaker Terminal
VTVM
IN
OUT
GND
Oscilloscope
AM Loop Antenna Jack
Figure 1-5
SET
AM VT(OR1)
OKV1 GND
Input
DC Voltmeter
594 KHz
OL 1
-
-- -
-
-
-
-
522 KHz
522 KHz
IT 2
OT 1
0.9V
Maximum output
Maximum output
Non Adjust
Non Adjust
Remark
FREQ. Setting
Adjust. PointSSG.FREQ.Item
Step
Connection
Alignment and Adjustments
Page 3
Samsung Electronics 1-3
1-2-1 Additional Test Equipment : Testing Tape
1. MTT-111 (or equipment) : Test tape on which 3KHz signal is recorded (Tape speed adjustment)
2. MTT-113CN (or equivalent) : Test tape on which 8KHz signal is recorded (Azimuth adjustment)
Tape speed
1
2
Figure 1-6
Figure 1-8
SVR Inside motor
Figure 1-7
3KHz
Maximum output and identical phase of L,R channel. Set the screw after adjustment
Remark
Adjustment Point
Location no.
Item
Step
Tape
Insert MTT-111 to
Deck.
Press PLAY button
Insert MTT-113CN
to Deck.
Press PLAY button
AZIMUTH (DECK) adjustment
TP3
Cassette Deck
Speaker Terminal
output
LINE OUT
Frequency Counter
Figure 1-6
Figure 1-7
Recording /Play head
REVERSE PLAY
AZIMUTH control knob
Figure 1-8
In Out
Speaker Terminal
Oscilloscope
SET
(GND)
VTVM
V H
1-2 Cassette Deck
Alignment and Adjustments
Loading...