SAMSUNG max960, Max980 Alignment and Adjustments

1-1Samsung Electronics

1. Alignment and Adjustments

1-1 Tuner

FM THD Adjustment

Output

23 dB

60 dB

Minumum Distortion (0.3% below) (Figure 1-1)

SSG FREQ.

Adjustment point (TL3)

98 MHz

FM DETECTOR COIL

FM Search Level Adjustment

Adjust TSR1 so that “TUNED” of FLT is lighted (Figure 1-2)

Figure1-2 FM Auto Search Level Adjustment

*Adjust FM S.S.G level to 23dB

Figure1-1 IF CENTER and THD Adjustment

SSG FREQ.

Adjustment point

(TSR1)

98 MHz

BEACON SENSITIVITY

SEMI-VR(5KΩ)

FM S.S.G

GND

23 dB

FM S.S.G

Output GND

Speaker Terminal

FM Antenna Terminal

Distortion Meter

Input

SET

Input

output

Oscilloscope

FM IN

FM Antenna

SET

5 kΩ

OUTPUT

AM SSG 450KHZ

INPUT

AM ANT IN

Speaker Terminal

60cm

TL2

VTVM Oscilloscope

AM(MW) I.F Adjustment

Maximum output (Figure 1-3)

SSG FREQ.

Frequency

Adjustment point (TL2)

450 kHz

522 kHz

AM I.F COIL

Figure1-3 AM I.F Adjustment

OUTPUT

* Adjustment Location of SW Band

* Adjustment Location of LW Band

(GND)

VTVM

Alignment and Adjustments

1-2 Samsung Electronics

1-2-1 To Adjust Tape Speed

1) Measuring tape: i) MTT-111 (or equivalent) (Tapes recorded with 3kHz)

ii) MTT-5512 (or equivalent)

2) Connect the cassette deck to the frequency counter

as in figure 1-4.

1) Before the actual adjustment, clean the play/recording

head.

2) Measuring tape :

i) MTT-114NA(or equivalent 12.5kHz AZIMUTH control)

ii) MTT-150(or equivalent : Dolby level 200nwb/m)

3) Dolby NR SW OFF

4) The cassette deck is connections as shown in figure 1-6.

Notes

NOR SPEED Control

OUT

(connected

to the frequency

counter)

Turn CVR1 to left and right

3KHz

6KHz

Turn CVR2 to left and right

Remark

Standard

To Adjust

Pre-Setup

Item

Step

Pre-Setup Condition

Same as above

1) Deck 1:MTT-111

2) Press PLAY

SW button

3) Deck 2:Same

as above

1) Deck 1:MTT-111

2) Deck 2:MTT-5512

3) Press DUBBING

SW button two times.

HI SPEED

Control

AZIMUTH

TP1 OUT

(VTVM is

connected to

the scope)

1) Turn the control screw to as shown in Figure 1-5.

2) Adjust the right

control screw to playback REV. Mode

Max output and same phase (both channels)

After adjustment secure it with REGION LOCK.

Adjust to level and same Aux level.

L-CH:Turn JSR2L

to the right and

left R-CH:Turn J SR2R to the right and left

See the diagram for adjustment locations.

Remark

Standard

To Adjust

Pre-Setup

Item

Step

Pre-Setup Condition

Same as above

After putting MTT-

114NA into Deck 1

1) Press FWD PLAY

button.

2) Press REV PLAY

button.

PLAY MTT-150

on Deck 1.

PlayBack out Level

AZIMUTH

TP1 OUT

(VTVM is

connected to

the scope)

1) Turn the control screw to as shown in Figure 1-5.

2)Adjust the right

control screw to playback REV. Mode

Max output and same phase (both channels)

After adjustment secure it with REGION LOCK.

Adjust to level and same Aux level.

L-CH:Turn JSR3L

to the right and left

R-CH:Turn JSR3R to

the right and left

See the diagram for adjustment locations.

Remark

Standard

To Adjust

Pre-Setup

Item

Step

Pre-Setup Condition

Same as above

After putting MTT-

114NA into Deck 2

1)Press FWD PLAY

button.

2)Press REV PLAY

button.

PLAY MTT-150

on Deck 2.

PlayBack out Level

1-2-2 To Adjust PlayBack Level

@ Adjust Deck 2 Play Level

! Adjust Deck 1 Play Level

Cassette Deck

output

SPK OUT

Frequency Counter

Figure 1-4

Figure 1-5

SPK OUT

Recording /Play head

FWD PLAY

REVERSE PLAY

AZIMUTH control screw

Figure 1-6

In Out

Cassette Deck

Oscilloscope

1-2 Cassette Deck

Fig1-8

+ 1 hidden pages