LTN154X3-L06 is a color active matrix TFT (Thin Film Transistor) liquid crystal display
(LCD) that uses amorphous silicon TFT as a switching devices. This model is composed of
a TFT LCD panel, a driver circuit and a backlight system. The resolution of a 15.4" contains
1280 x 800 pixels and can display up to 262,144 colors. 6 O'clock direction is the Optimum
viewing angle.
FEATURES
• Thin and light weight
• High contrast ratio, high aperture structure
• Wide XGA (1280x800 pixels) resolution
• Fast Response Time
• Low power consumption
• Single CCFL
• DE (Data enable) only mode.
• 3.3V LVDS Interface
• On board EDID chip
APPLICATIONS
• Notebook PC
• If the usage of this product is not for PC application, but for others, please contact SEC
www.jxlcd.com
GENERAL INFORMATION
Pixel pitch
www.jxlcd.com
331.2(H) X 207.0(V) (15.4”diagonal)Display area
a-si TFT active matrixDriver element
262,144Display colors
1280 x 800 ( 16 : 10, Wide XGA )Number of pixel
RGB vertical stripePixel arrangement
Note (1) Temperature and relative humidity range are shown in the figure below.
95 % RH Max. (40 °C ≥ Ta)
Maximum wet - bulb temperature at 39
www.jxlcd.com
www.jxlcd.com
100
-40-20020406080
Relative Humidity ( %RH)
95
80
60
40
20
Operating Range
Storage Range
5
0
O
C or less. (Ta > 40 °C ) No condensation
( 40,95 )
( 50,50.4 )
( 60,27.7 )
Temperature (OC)
(2) 2ms, half sine wave, one time for ±X, ±Y, ± Z.
(3) 5 - 500 Hz, random vibration, 30min for X, Y, Z.
(4) At testing Vibration and Shock, the fixture in holding the Module to be tested have to be
hard and rigid enough so that the Module would not be twisted or bent by the fixture.
DD + 0.3VDD –0.3VDDPower Supply Voltage
DD + 0.3VDD –0.3VDDLogic Input Voltage
Note (1) Within Ta (25 ± 2 °C)
(2) BACK-LIGHT UNIT
Lamp Current
Lamp frequency
Note 1) Permanent damage to the device may occur if maximum values are exceeded
Functional operation should be restricted to the conditions described under normal operating conditions.
www.jxlcd.com
www.jxlcd.com
L
L
(1)VV
(1)VV
Ta = 25 ± 2 °C
NoteUnitMax.Min.SymbolItem
(1)mArms6.53.0I
(1)kHz6550F
Samsung Secret
Doc.No.Rev.No
04-A02-G-070730
Page
/ 30LTN154X3-L06
6
Approval
2. OPTICAL CHARACTERISTICS
The following items are measured under stable conditions. The optical characteristics
should be measured in a dark room or equivalent state with the methods shown in Note (5).
Measuring equipment : TOPCON BM-5A and PR-650
* Ta = 25 ± 2 °C, VDD=3.3V, fv= 60Hz, fDCLK = 68.9MHz, IL = 6.0 mA
Contrast Ratio
(5 Points)
Response Time at Ta
( Rising + Falling )
Average Luminance
of White (5 Points)
Red
Color
Chromaticity
( CIE )
Green
www.jxlcd.com
Blue
www.jxlcd.com
White
CR
RT
L,AVE
Y
Unit
-
msec
-150125Y
Normal
X
Y
Y
Y
Viewing
Angle
φ = 0
θ = 0
0.6170.5870.557R
0.3740.3440.314R
0.3500.3200.290GX
0.5710.5410.511G
0.1850.1550.125BX
0.1700.1300.100B
0.3430.3130.283WX
0.3590.3290.299W
cd/m
-
2
NoteMaxTyp.Min.ConditionSymbolItem
(1), (2), (5)-400300
(1), (3)3525-T
I
L=6.0mA
(1), (4)
(1), (5)
PR-650
θ
L
Hor.
Viewing
Angle
13 Points
White Variation
Samsung Secret
Ver.
H
CR ≥ 10
L
L
Doc.No.Rev.No
4540
4540θ
1510φH
3025φ
04-A02-G-070730
Degrees
-
Page
(1), (5)
BM-5A
(6)1.6--δ
7
/ 30LTN154X3-L06
Note 1) Definition of Viewing Angle : Viewing angle range(10
Normal Line
o
φ = 0
,
θ = 0
θ L
φ L
L
=90
o
x
θ
φ H
≤ C/R)
o
θ R
Approval
12 O’clock
direction
y
φ
H
= 90
o
6 O’clock
direction
φ
Note 2) Definition of Contrast Ratio (CR) : Ratio of gray max (Gmax) ,gray min (Gmin)
at 5 points(4, 5, 7, 9, 10)
Points : , , , , at the figure of Note (6).
Note 3) Definition of Response time :
Display data
Optical
Response
o
= 90
L
CR(4) + CR(5) + CR(7) + CR(9) + CR(10)
CR =
49
www.jxlcd.com
www.jxlcd.com
100%
90%
10%
0%
5
White(TFT OFF)White(TFT OFF)
7
5
10
Black(TFT ON)
TR
x'y'
=90
θ
R
TF
o
Note 4) Definition of Average Luminance of White : measure the luminance of white at 5 points.
(320)( 640)(960)
5
L,AVE )
10
7
5
04-A02-G-070730
9
4
: test point
Average Luminance of White ( Y
Y
L4 + YL5 + YL7 + YL9 + YL10
YL,AVE =
Samsung Secret
Doc.No.Rev.No
Time
VIEW AREA
(200)
(400)
(600)
(lines)
Page
/ 30LTN154X3-L06
8
Approval
Note 5) After stabilizing and leaving the panel alone at a given te mperature for 30 min , the measurement
should be executed. Measurement should be executed in a stable, windless,and dark room.
30 min after lighting the backlight. This should be measured in the center of screen.
Lamp current : 6.0mA ( Inverter : SIC-130T )
Environment condition : Ta = 25 ± 2 °C
Photo-detector
( TOPCON BM-5A
PR-650 )
Field
= 2°
50 cm
TFT-LCD module
Center of the screen
[ Optical characteristics measurement setup ]
www.jxlcd.com
www.jxlcd.com
Note 6) Definition of 13 points white variation (δ L ), [ ~ ]
Maximum luminance of 13 points
δ L=
Minimum luminance of 13 points
10mm
320640
10mm
1312
10
113
960
9
LCD panel
10mm
11
200
8
5
3
10mm
Samsung Secret
Doc.No.Rev.No
7
4
2
04-A02-G-070730
6
400
600
(lines)
1
: test point
Page
/ 30LTN154X3-L06
9
Loading...
+ 21 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.