Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is
prohibited.
Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation.
VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.
Before Using the Product
An administration fee may be charged if either
(a) an engineer is called out at your request and there is no defect in the product
(i.e. where you have failed to read this user manual).
(b) you bring the unit to a repair center and there is no defect in the product
(i.e. where you have failed to read this user manual).
The amount of such administration charge will be advised to you before any work or home visit is
carried out.
Icons used in this manual
The following images are for reference only. Real-life situations may
differ from what is shown in the images.
Symbols for safety precautions
Warning
A serious or fatal injury may result if instructions are not followed.
Caution
Personal injury or damage to properties may result if instructions are
not followed.
Activities marked by this symbol are prohibited.
Instructions marked by this symbol must be followed.
Before Using the Product
7
Cleaning
!
Before Using the Product
Cleaning
Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
Take the following steps when cleaning.
1. Power off the monitor and computer.
2. Disconnect the power cord from the monitor.
Hold the power cable by the plug and do not touch the cable with wet
hands. Otherwise, an electric shock may result.
3. Wipe the monitor screen using a clean, soft and dry cloth.
Do not apply a cleaning agent that contains alcohol,
solvent, or surfactant to the monitor.
!
Do not spray water or detergent directly on the product.
4. Wet a soft and dry cloth in water and wring thoroughly to clean the
exterior of the monitor.
5. Connect the power cord to the product after cleaning the product.
6. Power on the monitor and computer.
Before Using the Product
8
Before Using the Product
3.93
inches
(10 cm)
3.93 inches(10 cm)
3.93
inches
(10 cm)
3.93 inches
(10 cm)
3.93 inches(10 cm)
Securing the Installation Space
Ensure some space around the product for ventilation. An internal temperature rise may cause fire
and damage the product. Be sure to allow the amount of space as shown below or greater when
installing the product.
The exterior may differ depending on the product.
Precautions for storage
Be sure to contact Samsung Customer Service Center (page 100) if the inside of the monitor needs
cleaning. (Service fee will be charged.)
Before Using the Product
9
Before Using the Product
!
!
!
Safety Precautions
Electricity and Safety
The following images are for reference only. Real-life situations may differ from what is shown in the
images.
Warning
Do not use a damaged power cord or plug, or a loose power socket.
An electric shock or fire may result.
Do not plug many products into the same power socket.
Otherwise, the socket may overheat and cause a fire.
Do not touch the power plug with wet hands.
Otherwise, an electric shock may result.
Insert the power plug all the way in so it is not loose.
An unstable connection may cause a fire.
Ensure you connect the power plug to a grounded power socket. (type 1
insulated devices only).
An electric shock or injury may result.
Do not bend or pull the power cord with force. Do not weigh the power cord
down with a heavy object.
A damaged power cord may cause an electric shock or fire.
Do not place the power cord or product near heat sources.
An electric shock or fire may result.
Remove foreign substances such as dust around the plug pins and power socket
with a dry cloth.
Otherwise, a fire may result.
Before Using the Product
10
Before Using the Product
!
!
!
!
Caution
Do not unplug the power cord when the product is in use.
The product may become damaged by an electric shock.
Do not use the power cord for products other than authorized products supplied
by Samsung.
An electric shock or fire may result.
Keep the power socket where the power cord is connected unobstructed.
If any problem occurs in the product, unplug the power cable to completely
cut the power to the product.
Power to the product cannot be completely cut off with the power button.
Hold the plug when disconnecting the power cord from the power socket.
An electric shock or fire may result.
Installation and Safety
Warning
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP
OF THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES.
Otherwise, a fire may result.
Avoid installing the product in a narrow space with bad ventilation, such as a
bookshelf or wall closet.
Otherwise, a fire may result due to an increased internal temperature.
Keep the plastic packaging bag for the product in a place that cannot be reached
by children.
Children may suffocate.
Before Using the Product
11
Before Using the Product
!
!
Do not install the product on an unstable or vibrating surface (insecure shelf,
sloped surface, etc.).
The product may fall and break or cause a personal injury.
Using the product in an area with excess vibration may damage the product
or cause a fire.
Do not install the product in a vehicle or a place exposed to dust, moisture (water
drips, etc.), oil, or smoke.
An electric shock or fire may result.
Do not expose the product to direct sunlight, heat, or a hot object such as a
stove.
Otherwise, the product lifespan may be reduced, or a fire may result.
Caution
Do not install the product within the reach of young children.
The product may fall and injure children.
Edible oil, such as soybean oil, can damage or deform the product. Do not install
the product in a kitchen or near a kitchen counter.
Take care not to drop the product when moving it.
Otherwise, product failure or personal injury may result.
Do not set down the product on its front.
The screen may become damaged.
When installing the product on a cabinet or shelf, make sure that the bottom
edge of the front of the product is not protruding.
The product may fall and break or cause a personal injury.
Install the product only on cabinets or shelves of the right size.
Before Using the Product
12
Before Using the Product
!
SAMSUNG
!
!
!
Put down the product carefully.
The product may fall and break or cause a personal injury.
Installing the product in an unusual place (a place exposed to a lot of fine
particles, chemical substances or extreme temperatures, or an airport or train
station where the product should operate continuously for an extended period of
time) may seriously affect its performance.
Be sure to consult Samsung Customer Service Center (page 100) before
installation if you want to install the product at such a place.
Operation and Safety
Warning
High voltage runs through the product. Do not attempt to disassemble, repair, or
modify the product on your own.
An electric shock or fire may result.
Contact Samsung Customer Service Center (page 100) for repair.
Before moving the product, turn off the power switch and disconnect the power
cable and all other connected cables.
Otherwise, the power cord may be damaged and a fire or electric shock may
result.
If the product generates a strange noise, a burning smell, or smoke, remove the
power cord immediately and contact Samsung Customer Service Center (page
100).
An electric shock or fire may result.
Do not let children hang from the product or climb on top of it.
The product may fall, and your child may become injured or seriously
harmed.
If the product falls or the exterior is damaged, power off the product, remove the
power cord, and contact Samsung Customer Service Center (page 100).
Otherwise, an electric shock or fire may result.
Do not put a heavy object, toy, or sweets on top of the product.
The product or heavy objects may fall as children try to reach for the toy or
sweets resulting in a serious injury.
Before Using the Product
13
Before Using the Product
!
!
!
GAS
!
100
During a lightning or thunderstorm, power off the product and remove the power
cable.
An electric shock or fire may result.
Do not drop objects on the product or apply impact.
An electric shock or fire may result.
Do not move the product by pulling the power cord or any cable.
Otherwise, the cable may be damaged and product failure, an electric shock
or fire may result.
If a gas leakage is found, do not touch the product or power plug. Also, ventilate
the area immediately.
Sparks can cause an explosion or fire.
Do not lift or move the product by pulling the power cord or any cable.
Otherwise, the cable may be damaged and product failure, an electric shock
or fire may result.
Do not use or keep combustible spray or an inflammable substance near the
product.
An explosion or fire may result.
Ensure the vents are not blocked by tablecloths or curtains.
Otherwise, a fire may result from an increased internal temperature.
Do not insert a metallic object (a chopstick, coin, hair pin, etc.) or inflammable
object (paper, match, etc.) into the vent or ports of the product.
If water or any foreign substance enters the product, be sure to power off the
product, remove the power cord, and contact Samsung Customer Service
Center (page 100).
Product failure, an electric shock or fire may result.
Do not place objects containing liquid (vases, pots, bottles, etc) or metallic
objects on top of the product.
If water or any foreign substance enters the product, be sure to power off the
product, remove the power cord, and contact Samsung Customer Service
Center (page 100).
Product failure, an electric shock or fire may result.
Before Using the Product
14
Before Using the Product
!
-_-
!
!
!
!
!
Caution
Leaving the screen fixed on a stationary image for an extended period of time
may cause afterimage burn-in or defective pixels.
If you are not going to use the product for an extended period of time,
activate power-saving mode or a moving-picture screen saver.
Disconnect the power cord from the power socket if you do not plan on using the
product for an extended period of time (vacation, etc.).
Otherwise, a fire may result from accumulated dust, overheating, an electric
shock, or electric leakage.
Use the product at the recommended resolution and frequency.
Otherwise,Your eyesight may deteriorate.
Looking at the screen too close for an extended period of time can deteriorate
your eyesight.
Do not hold the monitor upside-down or move it by holding the stand.
The product may fall and break or cause a personal injury.
Do not use humidifiers or stoves around the product.
An electric shock or fire may result.
Rest your eyes for more than 5 minutes for every 1 hour of product use.
Eye fatigue will be relieved.
Do not touch the screen when the product has been turned on for an extended
period of time as it will become hot.
Store the small accessories used with the product out of reach of children.
Before Using the Product
15
Before Using the Product
!
Exercise caution when adjusting the product angle or stand height.
Otherwise, children's fingers or hands may become stuck and injured.
Tilting the product excessively may cause it to fall and result in personal
injury.
Do not place heavy objects on the product.
Product failure or personal injure may result.
Correct posture to use the product
Use the product in the correct posture as follows.
Straighten your back.
Allow a distance of 45 to 50cm between your eye and the screen, and look slightly
downward at the screen.
Keep your eyes directly in front of the screen.
Adjust the angle so light does not reflect on the screen.
Keep your forearms perpendicular to your upper arms and level with the back of
your hands.
Keep your elbows at about a right angle.
Adjust the height of the product so you can keep your knees bent at 90 degrees or
more, your heels attached to the floor, and your arms lower than your heart.
Before Using the Product
16
Preparations
1
1.1Checking the Contents
1.1.1Removing the Packaging
1Open the packaging box. Be careful not to damage the product when you open the packaging with
a sharp instrument.
2Remove the styrofoam from the product.
3Check the components and remove the styrofoam and plastic bag.
4Store the box in a dry area so that it can be used when moving the product in the future.
This image is for reference only.
1 Preparations
17
1
Preparations
1.1.2Checking the Components
Contact the dealer from whom you purchased the product if any item is missing.
The appearance of the components and items sold separately may differ from the image shown.
Components
Quick setup guide
Power cableD-SUB cable (optional)DVI cable (optional)
StandStand Connector
Components may vary depending on the country.
(Not available in some locations)
Warranty card
User manual
1 Preparations
18
Preparations
Key Guide
SAMSUNG
MAGIC
ANGLE
AUTO
MENU
M
M
SAMSUNG
MAGIC
SAMSUNG
MAGIC
1
1.2Parts
1.2.1Frontal Buttons
The color and shape of parts may differ from what is shown. Specifications are subject to change
without notice to improve quality.
IconsDescription
Open or close the onscreen display (OSD) menu, or return to the
parent menu.
OSD control lock: Maintain the current settings, or lock the OSD
control to prevent unintended changes to settings.
Enable: To lock the OSD control, press the [] button for 10
seconds.
Disable: To unlock the locked OSD control, press the [] button
for more than 10 seconds.
If the OSD control is locked,
Brightness and Contrast can be adjusted, and INFORMATION
can be viewed.
The Customized Key function can be used by pressing the []
button. (The Customized Key is available even when the OSD
control is locked.)
Configure Customized Key and press []. The following options will
be enabled.
- Bright - Eco Saving - Image Size
Angle
To configure Customized Key, go to SETUP&RESET
Customized Key
Move to the upper or lower menu or adjust the value for an option on the
OSD menu.
and select the mode you want.
ENU
ENU
→
1 Preparations
19
1
AUTO
AUTO
Preparations
IconsDescription
Use this button to control the brightness and contrast of the screen.
Confirm a menu selection.
Pressing the [] button when the OSD menu is not displayed will
change the input source (Analog/DVI). If you power on the product or
change the input source by pressing the [] button, a message that
shows the changed input source will appear at the top left corner of the
screen.
This function is not available for products with an Analog interface
only.
Press the [] button to automatically adjust the screen settings.
Changing the resolution in Display Properties will activate the
Auto Adjustment function.
Key Guide
This function is only available in Analog mode.
Turn the screen on or off.
When a control button on the product is pressed, the Key Guide will be
displayed before the onscreen menu opens. (The guide shows the
function of the button pressed.)
To access the onscreen menu when the guide is displayed, press the
corresponding button again.
The Key Guide may vary depending on the function or product model.
Refer to the actual product.
1 Preparations
20
1
DVI INRGB IN
POWER IN
RGB INDVI IN
POWER IN
Preparations
1.2.2Reverse Side
The color and shape of parts may differ from what is shown. Specifications are subject to change
without notice to improve quality.
PortPorts
Connect the power cord for your monitor to the POWER IN port on
the back of the product.
Connect to a PC using the DVI cable.
The [DVI IN] terminal is supplied for the digital (DVI)-dedicated
models only.
Connect to a PC using the D-SUB cable.
1 Preparations
21
Preparations
1
1.3Installation
1.3.1Attaching the Stand
Before assembling the product, place the product down on a flat and stable surface so that the screen
is facing downwards.
Insert the Stand Connector into
the Stand in the direction shown
by the figure.
Place a soft cloth over the table
to protect the product and place
the product onto the cloth so
that the front of the product is
facing downwards.
The color and shape of parts may differ from what is shown. Specifications are subject to change
without notice to improve quality.
Check if the Stand Connector is
firmly connected.
Hold the main body of the
product with your hand as
shown by the figure.
Push the assembled stand into
the main body in the direction of
the arrow as shown in the figure.
Turn the connecting screw at the
bottom of the stand fully so that it
is completely fixed.
- Caution
Do not hold the product upside
down only by the stand.
1 Preparations
22
1
-1° (±2°) ~ 20° (±2°)
Preparations
1.3.2Adjusting the Product Tilt
The color and shape of parts may differ from what is shown. Specifications are subject to change
without notice to improve quality.
You can adjust the tilt of your monitor.
Hold the lower part of the product and adjust the tilt carefully.
1 Preparations
23
1
2
3
B
4
A
B
Preparations
1.3.3Installing a Wall-mount Kit or Desktop Stand
Before Installation
Power the product off and remove the power cable from the power socket.
Place a protective cloth or cushion on a flat
surface. Next, place the product with the face
down on top of the cloth or cushion.
Installing a Wall-mount Kit or Desktop Stand
1
Hold the main body of the product with your hand
as shown by the figure.
Pull the stand in the direction of the arrow as
shown in the figure to separate it.
A
Attach the wall-mount kit or desktop stand here
Bracket (sold separately)
Align the grooves and tightly fasten the screws on the bracket on the product with the corresponding
parts on the wall-mount kit or desktop stand you want to attach.
1 Preparations
24
1
RGB INDVI IN
POWER IN
Preparations
Notes
Using a screw longer than the standard length can damage the internal components of the
product.
The length of screws required for a wall mount that does not comply with the VESA standards may
vary depending on the specifications.
Do not use screws that do not comply with the VESA standards. Do not attach the wall-mount kit
or desktop stand using excessive force. The product may get damaged or fall and cause personal
injury. Samsung shall not be held liable for any damage or injury caused by using improper screws
or attaching the wall-mount kit or desktop stand using excessive force.
Samsung shall not be held liable for any product damage or personal injury caused by using a wall-
mount kit other than the one specified or from an attempt to install the wall-mount kit on your own.
To mount the product on a wall, ensure you purchase a wall-mount kit that can be installed 10cm
or farther away from the wall.
Be sure to use a wall-mount kit that complies with the standards.
1.3.4Anti-theft Lock
An anti-theft lock allows you to use the product securely even in public places. The locking device shape
and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft
locking device for details. The lock device is sold separately.
The color and shape of parts may differ from what is shown. Specifications are subject to change
without notice to improve quality.
To lock an anti-theft locking device:
1Fix the cable of your anti-theft locking device to a heavy object such as a desk.
2Put one end of the cable through the loop on the other end.
3Insert the locking device into the anti-theft lock slot at the back of the product.
4Lock the locking device.
An anti-theft locking device can be purchased separately.
Refer to the user guide provided with your anti-theft locking device for details.
Anti-theft locking devices can be purchased at electronics retailers or online.
1 Preparations
25
Connecting and Using a Source Device
RGB INDVI IN
POWER IN
POWER IN
2
2.1Before Connecting
2.1.1Pre-connection Checkpoints
Before connecting a source device, read the user manual provided with it.
The number and locations of ports on source devices may differ from device to device.
Do not connect the power cable until all connections are completed.
Connecting the power cable during connection may damage the product.
Check the types of ports at the back of the product you want to connect.
2.2Connecting the Power
To use the product, connect the power cable to a power outlet and the [POWER IN] port on the
product.(The input voltage is switched automatically.)
2 Connecting and Using a Source Device
26
Connecting and Using a Source Device
RGB IN
DVI IN
2
2.3Connecting and Using a PC
2.3.1Connecting to a PC
Select a connection method suitable for your PC.
Connecting parts may differ in different products.
Connection Using the D-SUB Cable (Analog Type)
Do not connect the power cable before connecting all other cables. Ensure you connect a source
device first before connecting the power cable.
1
Connect the D-SUB cable to the [RGB IN] port on the back of the product and the RGB port on the PC.
2Press [] to change the input source to Analog.
Connection Using the DVI Cable
This function is not available for products with an Analog interface only.
Do not connect the power cable before connecting all other cables. Ensure you connect a source
device first before connecting the power cable.
1Connect the DVI cable to the [DVI IN] port on the back of the product and the DVI port on the PC.
2Press [] to change the input source to DVI.
The [DVI IN] terminal is supplied for the digital (DVI)-dedicated models only.
2 Connecting and Using a Source Device
27
2
Connecting and Using a Source Device
2.3.2Driver Installation
You can set the optimum resolution and frequency for this product by installing the corresponding
drivers.
An installation driver is contained on the CD supplied with the product.
If the file provided is faulty, visit the Samsung homepage (http://www.samsung.com) and
download the file.
1Insert the user manual CD provided with the product into the CD-ROM drive.
2Click "Windows Driver".
3Follow the instructions given on the screen to proceed with installation.
4Select your product model from the list of models.
5Go to Display Properties and check that the resolution and refresh rate are appropriate.
Refer to your Windows OS manual for further details.
2 Connecting and Using a Source Device
28
2
EXIT
AUTO
The optimal resolution for this
monitor is as follows:
**** x **** **Hz
Use the above settings to set
the resolution on your PC.
English
M
Connecting and Using a Source Device
2.3.3Setting Optimum Resolution
An information message about setting optimum resolution will appear if you power on the product for the
first time after purchase.
Select a language on the product and change the resolution on your PC to the optimum setting.
1Press [] to move to the language you want and press [].
2To hide the information message, press [].
If the optimum resolution is not selected, the message will appear up to three times for a specified
time even when the product is turned off and on again.
The optimum resolution can also be selected in Control Panel on your PC.
ENU
2 Connecting and Using a Source Device
29
2
12
3
**** ****
**********
Connecting and Using a Source Device
2.3.4Changing the Resolution Using a PC
Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture
quality.
The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected.
Changing the Resolution on Windows XP
Go to Control PanelDisplay Settings and change the resolution.
2 Connecting and Using a Source Device
30
2
12
34
***********
***********
Connecting and Using a Source Device
Changing the Resolution on Windows Vista
Go to Control PanelPersonalization Display Settings and change the resolution.
2 Connecting and Using a Source Device
31
2
12
34
Connecting and Using a Source Device
Changing the Resolution on Windows 7
Go to Control PanelDisplay Screen Resolution and change the resolution.
2 Connecting and Using a Source Device
32
Connecting and Using a Source Device
12
34
5
2
Changing the Resolution on Windows 8
Go to Settings Control Panel Display Screen Resolution and change the resolution.
2 Connecting and Using a Source Device
33
Screen Setup
SAMSUNG
MAGIC
MENU
Custom
Off
Off
: Auto
PICTURE
Brightness
Contrast
Sharpness
Image Size
SAMSUNG
MAGIC
Bright
SAMSUNG
MAGIC
Angle
AUTO
SAMSUNG
MAGIC
Upscale
3
Configure the screen settings such as brightness.
3.1Brightness
You can adjust the general brightness of the picture. (Range: 0~100)
A higher value will make the picture appear brighter.
This menu is not available when Bright is set to Dynamic Contrast mode.
This menu is unavailable when Eco Saving is set.
3.1.1Configuring Brightness
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to PICTURE and press [] on the product.
3Press [] to move to Brightness and press [] on the product. The following screen will
appear.
4Adjust the Brightness using the [] buttons.
3 Screen Setup
34
Screen Setup
SAMSUNG
MAGIC
MENU
&XVWRP
2II
2II
Auto
PICTURE
SAMSUNG
MAGIC
Bright
SAMSUNG
MAGIC
Angle
Brightness
Contrast
Sharpness
Image Size
AUTO
SAMSUNG
MAGIC
Upscale
3
3.2Contrast
Adjust the contrast between the objects and background. (Range: 0~100)
A higher value will increase the contrast to make the object appear clearer.
This menu is not available when Bright is in Cinema or Dynamic Contrast mode.
3.2.1Configuring Contrast
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to PICTURE and press [] on the product.
3Press [] to move to Contrast and press [] on the product. The following screen will
appear.
4Adjust the Contrast using the [] buttons.
3 Screen Setup
35
Screen Setup
SAMSUNG
MAGIC
SAMSUNG
MAGIC
MENU
Custom
Off
Off
: Auto
PICTURE
SAMSUNG
MAGIC
Bright
SAMSUNG
MAGIC
Angle
Brightness
Contrast
Sharpness
Image Size
AUTO
SAMSUNG
MAGIC
Upscale
3
3.3Sharpness
Make the outline of objects more clear or blurry. (Range: 0~100)
A higher value will make the outline of objects clearer.
This menu is not available when Bright is in Cinema or Dynamic Contrast mode.
This menu is not available when Upscale is in Mode1 or Mode2.
3.3.1Configuring Sharpness
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to PICTURE and press [] on the product.
3Press [] to move to Sharpness and press [] on the product. The following screen will
appear.
4Adjust the Sharpness using the [] buttons.
3 Screen Setup
36
Screen Setup
SAMSUNG
MAGIC
MENU
SAMSUNG
MAGIC
یࡈ࣏ࢽ
ଥࢿ
Auto
PICTURE
SAMSUNG
MAGIC
Bright
Custom
Standard
Game
Cinema
Dynamic Contrast
SAMSUNG
MAGIC
Angle
Brightness
Contrast
Sharpness
Image Size
AUTO
SAMSUNG
MAGIC
Upscale
3
3.4SAMSUNG MAGIC Bright
This menu provides an optimum picture quality suitable for the environment where the product will be
used.
This menu is unavailable when Eco Saving is set.
This menu is not available when Angle is enabled.
You can customize the brightness to suit your preferences.
3.4.1Configuring SAMSUNG MAGIC Bright
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to PICTURE and press [] on the product.
3Press [] to move to Bright and press [] on the product. The following screen will
appear.
Custom: Customize the contrast and brightness as required.
Standard: Obtain a picture quality suitable for editing documents or using Internet.
Game: Obtain a picture quality suitable for playing games that involve many graphic effects and
dynamic movements.
Cinema: Obtain the brightness and sharpness of TVs suitable for enjoying video and DVD
content.
Dynamic Contrast: Obtain balanced brightness through automatic contrast adjustment.
4Press [] to move to the option you want and press [].
5The selected option will be applied.
3 Screen Setup
37
Screen Setup
SAMSUNG
MAGIC
SAMSUNG
MAGIC
MENU
SAMSUNG
MAGIC
یࡈ࣏ࢽ
ଥࢿ
PICTURE
SAMSUNG
MAGIC
Angle
Off
Lean Back Mode 1
Lean Back Mode 2
Standing Mode
Side Mode
Group View
Custom
SAMSUNG
MAGIC
Bright
Brightness
Contrast
Sharpness
Image Size
AUTO
SAMSUNG
MAGIC
Upscale
4
2
3
1
1
55
②
③
④
⑤
①
④
3
3.5SAMSUNG MAGIC Angle
Angle allows you to configure the settings to obtain the optimum picture quality according to your
viewing angle.
This menu is not available when Bright is in Cinema or Dynamic Contrast mode.
This menu is not available for S19C200NY and S22C200NY models.
You can customize the angle to suit your preferences.
3.5.1Configuring SAMSUNG MAGIC Angle
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to PICTURE and press [] on the product.
3Press [] to move to Angle and press [] on the product. The following screen will
appear.
Off : Select this option to view directly in front of the product.
Lean Back Mode 1 : Select this option to view from a place slightly lower than the product.
Lean Back Mode 2 : Select this option to view from a place lower than Lean Back Mode 1.
Standing Mode : Select this option to view from a place higher than the product.
Side Mode : Select this option to view from either side of the product.
Group View: Select this option for more than one viewer to view from places , , and .
Custom: Lean Back Mode 1 will be applied by default if Custom is selected.
4Press [] to move to the option you want and press [].
5The selected option will be applied.
①
3 Screen Setup
⑤
38
Screen Setup
SAMSUNG
MAGIC
SAMSUNG
MAGIC
MENU
SAMSUNG
MAGIC
Custom
OffAuto
PICTURE
Brightness
Contrast
Sharpness
Image Size
SAMSUNG
MAGIC
Bright
SAMSUNG
MAGIC
Upscale
Off
Mode1
Mode2
MoveEnterReturn
Off
SAMSUNG
MAGIC
Angle
AdjustEnterReturn
AUTO
AUTO
AUTO
AUTO
AUTO
3
3.6SAMSUNG MAGIC Upscale
Upscale function can enhance the layers of the picture details and the vividness of the picture.
The function has more obvious effects on low-resolution pictures.
This menu is not available when Bright is in Cinema or Dynamic Contrast mode.
3.6.1Configuring SAMSUNG MAGIC Upscale
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to PICTURE and press [] on the product.
3Press [] to move to Upscale and press [] on the product. The following screen
will appear.
Comparing with Mode1, Mode2 has a stronger effect.
4Press [] to move to the option you want and press [].
5The selected option will be applied.
3 Screen Setup
39
Screen Setup
MENU
Custom
Off
PICTURE
SAMSUNG
MAGIC
Bright
SAMSUNG
MAGIC
Angle
Brightness
Contrast
Sharpness
Image Size
$XWR
:LGH
AUTO
SAMSUNG
MAGIC
Upscale
Custom
Off
PICTURE
SAMSUNG
MAGIC
Bright
SAMSUNG
MAGIC
Angle
Brightness
Contrast
Sharpness
Image Size
AUTO
6FUHHQ)LW
SAMSUNG
MAGIC
Upscale
3
3.7Image Size
Change the picture size.
3.7.1Changing the Image Size
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to PICTURE and press [] on the product.
3Press [] to move to Image Size and press [] on the product. The following screen will
appear.
Auto: Display the picture according to the aspect ratio of the input source.
Wide: Display the picture in full screen regardless of the aspect ratio of the input source.
4:3: Display the picture with an aspect ratio of 4:3. Suitable for videos and standard broadcasts.
16:9: Display the picture with an aspect ratio of 16:9.
Screen Fit: Display the picture with the original aspect ratio without cutting off.
3 Screen Setup
40
3
Custom
Off
PICTURE
SAMSUNG
MAGIC
Bright
SAMSUNG
MAGIC
Angle
Brightness
Contrast
Sharpness
Image Size
AUTO
:LGH
6FUHHQ)LW
SAMSUNG
MAGIC
Upscale
Screen Setup
4:3: Display the picture with an aspect ratio of 4:3. Suitable for videos and standard broadcasts.
Wide: Display the picture in full screen regardless of the aspect ratio of the input
source.(S19C200NW/S19C200BW/S22C200BW)
Screen Fit: Display the picture with the original aspect ratio without cutting off.
Changing the screen size is available when the following conditions are satisfied,except
S19C200NR and S19C200BR models.
A digital output device is connected using the DVI cable.
The input signal is 480p, 576p, 720p, or 1080p and monitor can display normally(not every
model can support all of these signals ).
This can only be set when the external input is connected through DVI and PC/AV Mode is
set to AV.
4Press [] to move to the option you want and press [].
5The selected option will be applied.
3 Screen Setup
41
Screen Setup
MENU
PICTURE
H-Position
V-Position
Coarse
Fine
AUTO
PICTURE
H-Position
V-Position
Coarse
Fine
AUTO
3
3.8H-Position & V-Position
H-Position: Move the screen to the left or right.
V-Position: Move the screen up or down.
This menu is available in Analog mode.
This menu is only available when Image Size is set to Screen Fit in AV Mode. When a 480P or
576P or 720P or 1080P signal is input in AV mode and the monitor can display normally ,select
Screen Fit to adjust horizontal position in 0-6 levels.
3.8.1Configuring H-Position & V-Position
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to PICTURE and press [] on the product.
3Press [] to move to H-Position or V-Position, and press []. The following screen will
appear.
4Press [] to configure H-Position or V-Position.
3 Screen Setup
42
Screen Setup
MENU
PICTURE
H-Position
V-Position
Coarse
Fine
AUTO
3
3.9Coarse
Adjust the screen frequency.
This menu is available in Analog mode only.
3.9.1Adjusting Coarse
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to PICTURE and press [] on the product.
3Press [] to move to Coarse and press [] on the product. The following screen will
appear.
4Adjust the Coarse using the [] buttons.
3 Screen Setup
43
Screen Setup
MENU
PICTURE
H-Position
V-Position
Coarse
Fine
AUTO
3
3.10Fine
Fine-adjust the screen to obtain a vivid picture.
3.10.1Adjusting Fine
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to PICTURE and press [] on the product.
3Press [] to move to Fine and press [] on the product. The following screen will appear.
This menu is available in Analog mode only.
4Adjust the Fine using the [] buttons.
3 Screen Setup
44
Configuring Tint
SAMSUNG
MAGIC
MENU
COLOR
:
:
:
:
:
Red
Green
Blue
Color Tone
Gamma
Mode1
Normal
AUTO
4
Adjust the tint of the screen. This menu is not available when Bright is set to Cinema or
Dynamic Contrast mode.
4.1Red
Adjust the value of the color red in the picture. (Range: 0~100)
A higher value will increase the intensity of the color.
4.1.1Configuring Red
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to COLOR and press [] on the product.
3Press [] to move to Red and press [] on the product. The following screen will appear.
4Adjust the Red using the [] buttons.
4 Configuring Tint
45
Configuring Tint
MENU
COLOR
:
:
:
:
:
Red
Green
Blue
Color Tone
Gamma
Mode1
Normal
AUTO
4
4.2Green
Adjust the value of the color green in the picture. (Range: 0~100)
A higher value will increase the intensity of the color.
4.2.1Configuring Green
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to COLOR and press [] on the product.
3Press [] to move to Green and press [] on the product. The following screen will appear.
4Adjust the Green using the [] buttons.
4 Configuring Tint
46
Configuring Tint
MENU
COLOR
:
:
:
:
:
Mode1
Normal
Red
Green
Blue
Color Tone
Gamma
AUTO
4
4.3Blue
Adjust the value of the color blue in the picture. (Range: 0~100)
A higher value will increase the intensity of the color.
4.3.1Configuring Blue
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to COLOR and press [] on the product.
3Press [] to move to Blue and press [] on the product. The following screen will appear.
4Adjust the Blue using the [] buttons.
4 Configuring Tint
47
Configuring Tint
SAMSUNG
MAGIC
MENU
COLOR
:
:
:
:
:
ֻҖ
ࣱ
&RRO
&RRO
1RUPDO
:DUP
:DUP
&XVWRP
Red
Green
Blue
Color Tone
Gamma
AUTO
4
4.4Color Tone
Adjust the general color tone of the picture.
This menu is not available when Angle is enabled.
4.4.1Configuring the Color Tone Settings
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to COLOR and press [] on the product.
3Press [] to move to Color Tone and press [] on the product. The following screen will
appear.
Cool 2: Set the color temperature to be cooler than Cool 1.
Cool 1: Set the color temperature to be cooler than Normal mode.
Normal: Display the standard color tone.
Warm 1: Set the color temperature to be warmer than Normal mode.
Warm 2: Set the color temperature to be warmer than Warm 1.
Custom: Customize the color tone.
4Press [] to move to the option you want and press [].
5The selected option will be applied.
4 Configuring Tint
48
Configuring Tint
SAMSUNG
MAGIC
MENU
COLOR
:
:
:
:
:
ֻҖ
Normal
Mode1
Mode2
Mode3
Red
Green
Blue
Color Tone
Gamma
AUTO
4
4.5Gamma
Adjust the mid-range brightness (Gamma) of the picture.
This menu is not available when Angle is enabled.
4.5.1Configuring Gamma
1Press any button on the front of the product to display the Key Guide. Next, press [] to display
the corresponding menu screen.
2Press [] to move to COLOR and press [] on the product.
3Press [] to move to Gamma and press [] on the product. The following screen will
appear.
4Press [] to move to the option you want and press [].
MultiScreen enables users to use the monitor by partitioning multiple sections.
8.2.1Installing the Software
1Insert the installation CD into the [CD-ROM drive].
2Select the "MultiScreen" setup program.
3When the Installation Wizard appears, click [Next].
If the pop-up screen for the software installation does not appear on the main screen, find and
double-click the "MultiScreen" setup file on the [CD-ROM].
4Follow the instructions given on the screen to proceed with installation.
Restrictions and Problems with the Installation (MultiScreen)
The "MultiScreen" installation may be affected by the [Graphics card], [Motherboard] and the [Networking
environment].
Operating System
"OS"
"Windows 2000"
"Windows XP Home Edition"
"Windows XP Professional"
"Windows Vista 32bit"
"Windows 7 32bit"
The software may not work properly if you do not restart the computer after the installation.
The "MultiScreen" icon may not appear depending on the computer system and the product
specifications.
If the shortcut icon does not appear, press the F5 key.
"Windows 8 32bit"
For "MultiScreen", the operating systems "Windows 2000" or later is recommended.
"Hardware"
At least 32MB of memory
At least 60MB of free space on the hard disk drive
8 Installing the Software
66
8
Installing the Software
8.2.2Removing the Software
Click [Start], select [Settings]/[Control Panel], and then double-click [Add or Remove Programs].
Select "MultiScreen" from the program list and click the [Add/Delete] button.
8 Installing the Software
67
Troubleshooting Guide
9
9.1Requirements Before Contacting Samsung Customer
Service Center
9.1.1Testing the Product
Before calling Samsung Customer Service Center, test your product as follows. If the problem persists,
contact Samsung Customer Service Center.
Check if your product is operating normally by using the product test function.
If the screen is turned off and the power indicator blinks even though the product is properly connected
to a PC, perform a self-diagnosis test.
1Power off both the PC and product.
2Disconnect the cables from the product.
3Power on the product.
4If the message "Check Signal Cable" appears, the product is working normally.
9.1.2Checking the Resolution and Frequency
For a mode that exceeds the supported resolution (refer to "10.3 Standard Signal Mode Table"), the
message "Not Optimum Mode" will appear for a short time.
9.1.3Check the following.
The screen keeps switching on and off. Check the cable connection between the product
If the screen remains blank, check the PC system, video controller and cable.
Installation issue (PC mode)
and PC, and ensure the connectors are locked.
(Refer to "2.3 Connecting and Using a PC")
Screen issue
The power LED is off. The screen will not switch
on.
The message "Check Signal Cable" appears. Check that the cable is properly connected to the
Check that the power cable is connected
properly. (Refer to "2.3 Connecting and Using a
PC")
product. (Refer to "2.3 Connecting and Using a
PC")
Check that the device connected to the product is
powered on.
9 Troubleshooting Guide
68
9
Troubleshooting Guide
Screen issue
"Not Optimum Mode" is displayed. This message appears if the signal from the
graphics card exceeds the maximum resolution or
frequency for the product.
Change the maximum resolution and frequency to
suit the product performance, referring to
Standard Signal Mode Table (page 86).
The images on the screen look distorted.Check the cable connection to the product (Refer
to "2.3 Connecting and Using a PC")
The screen is not clear. The screen is blurry.Adjust Coarse (page 43) and Fine (page 44).
Remove any accessories (video extension cable,
etc.) and try again.
Set the resolution and frequency to the
recommended level. (Refer to "10.1 General")
The screen appears unstable and shaky.Check that the resolution and frequency for the
There are shadows or ghost images left on the
screen.
The screen is too bright. The screen is too dark.Adjust Brightness (page 34) and Contrast (page
Screen color is inconsistent.Change the COLOR settings.
The colors on the screen have a shadow and are
distorted.
White does not really look white.Change the COLOR settings.
There is no image on the screen and the power
LED blinks every 0.5 to 1 second.
PC are within the range of resolution and
frequency compatible with the product. Next, if
required, change the settings, referring to
Standard Signal Mode Table (page 86) in this
manual and the INFORMATION menu on the
product.
35).
(Refer to " Configuring Tint")
Change the COLOR settings.
(Refer to " Configuring Tint")
(Refer to " Configuring Tint")
The product is operating in power-saving mode.
Press any key on the keyboard or move the
mouse to return to normal operating mode.
Source device issue
A beeping sound is heard when my PC is booting.If a beeping sound is heard when your PC is
booting, have your PC serviced.
9 Troubleshooting Guide
69
Troubleshooting Guide
9
9.2Q & A
QuestionAnswer
How can I change the
frequency?
Set the frequency on your graphics card.
Windows XP: Go to Control Panel Appearance and
Themes Display Settings Advanced Monitor,
and adjust Refresh rate under Monitor settings.
Windows ME/2000: Go to Control Panel Display
Settings Advanced Monitor, and adjust Refresh rate
under Monitor settings.
Windows Vista: Go to Control Panel Appearance and
Personalization Personalization Display Settings
Advanced Settings Monitor, and adjust Refresh rate
under Monitor settings.
Windows 7: Go to Control Panel Appearance and
Personalization Display Screen Resolution
Advanced settings Monitor, and adjust Refresh rate under
Monitor settings.
Windows 8: Go to Settings Control Panel Appearance
and Personalization Display Screen Resolution
Advanced settings Monitor, and adjust Refresh rate under
Monitor settings.
9 Troubleshooting Guide
70
9
Troubleshooting Guide
QuestionAnswer
How can I change the
resolution?
How do I set power-saving
mode?
Windows XP: Go to Control Panel Appearance and
Themes Display Settings, and adjust the resolution.
Windows ME/2000: Go to Control Panel Display
Settings, and adjust the resolution.
Windows Vista: Go to Control Panel Appearance and
Personalization Personalize Display Settings, and
adjust the resolution.
Windows 7: Go to Control Panel Appearance and
Personalization Display Adjust Resolution, and adjust
the resolution.
Windows 8: Go to Settings Control Panel Appearance
and Personalization Display Adjust Resolution, and
adjust the resolution.
Windows XP: Set power-saving mode in Control Panel
Appearance and Themes Display Screen Saver
Settings or BIOS SETUP on the PC.
Windows ME/2000: Set power-saving mode in Control Panel
DisplayScreen Saver Settings or BIOS SETUP on the
PC.
Windows Vista: Set power-saving mode in Control Panel
Appearance and Personalization Personalize Screen
Saver Settings or BIOS SETUP on the PC.
Windows 7: Set power-saving mode in Control Panel
Appearance and Personalization Personalize Screen
Saver Settings or BIOS SETUP on the PC.
Windows 8: Set power-saving mode in Settings Control
Panel Appearance and Personalization Personalize
Screen Saver Settings or BIOS SETUP on the PC.
Refer to the user manual for your PC or graphics card for further instructions on adjustment.
This monitor can be installed and used with any Plug-and-Play
compatible systems. Two-way data exchange between the monitor
and PC system optimizes the monitor settings. Monitor installation
takes place automatically. However, you can customize the
installation settings if desired.
Due to the nature of the manufacturing of this product,
approximately 1 pixel per million (1ppm) may be brighter or darker on
the LCD panel. This does not affect product performance.
This monitor can be installed and used with any Plug-and-Play
compatible systems. Two-way data exchange between the monitor
and PC system optimizes the monitor settings. Monitor installation
takes place automatically. However, you can customize the
installation settings if desired.
Due to the nature of the manufacturing of this product,
approximately 1 pixel per million (1ppm) may be brighter or darker on
the LCD panel. This does not affect product performance.
This monitor can be installed and used with any Plug-and-Play
compatible systems. Two-way data exchange between the monitor
and PC system optimizes the monitor settings. Monitor installation
takes place automatically. However, you can customize the
installation settings if desired.
Due to the nature of the manufacturing of this product,
approximately 1 pixel per million (1ppm) may be brighter or darker on
the LCD panel. This does not affect product performance.
10 Specifications
77
10
Specifications
Model NameS22C200BS22C200BW
Size21.5 Inches (54 cm)22.0 Inches (55 cm)
Panel
Synchronization
Display Color16.7M
Resolution
Maximum Pixel Clock148MHz (Analog,Digital)146MHz (Analog,Digital)
Power Supply
Display area
Pixel Pitch
Horizontal
Frequency
Vertical
Frequency
Optimum
Resolution
Maximum
Resolution
476.64 mm (H) x 268.11 mm (V)
18.8 Inches (H) x 10.6 Inches (V)
0.24825 mm (H) x 0.24825 mm (V)
0.010 Inches (H) x 0.010 Inches (V)
30 ~ 81 kHz
56 ~ 75 Hz
1920x1080@60Hz1680x1050@60Hz
1920x1080@60Hz1680x1050@60Hz
This product uses 100 to 240V.
Refer to the label at the back of the product as the standard voltage
can vary in different countries.
This monitor can be installed and used with any Plug-and-Play
compatible systems. Two-way data exchange between the monitor
and PC system optimizes the monitor settings. Monitor installation
takes place automatically. However, you can customize the
installation settings if desired.
Due to the nature of the manufacturing of this product,
approximately 1 pixel per million (1ppm) may be brighter or darker
on the LCD panel. This does not affect product performance.
10 Specifications
79
10
Specifications
Model NameS22C210BS23C200B
Size21.5 Inches (54 cm)23.0 Inches (58 cm)
Panel
Synchronization
Display Color16.7M
Resolution
Maximum Pixel Clock148MHz (Analog,Digital)148MHz (Analog,Digital)
Power Supply
Display area
Pixel Pitch
Horizontal
Frequency
Vertical
Frequency
Optimum
Resolution
Maximum
Resolution
476.64 mm (H) x 268.11 mm (V)
18.8 Inches (H) x 10.6 Inches (V)
0.24825 mm (H) x 0.24825 mm (V)
0.010 Inches (H) x 0.010 Inches (V)
30 ~ 81 kHz
56 ~ 75 Hz
1920x1080@60Hz1920x1080@60Hz
1920x1080@60Hz1920x1080@60Hz
This product uses 100 to 240V.
Refer to the label at the back of the product as the standard voltage
can vary in different countries.
This monitor can be installed and used with any Plug-and-Play
compatible systems. Two-way data exchange between the monitor
and PC system optimizes the monitor settings. Monitor installation
takes place automatically. However, you can customize the
installation settings if desired.
Due to the nature of the manufacturing of this product,
approximately 1 pixel per million (1ppm) may be brighter or darker
on the LCD panel. This does not affect product performance.
10 Specifications
81
10
Specifications
Model NameS24C200BL
Size23.6 Inches (59 cm)
Panel
Synchronization
Display Color16.7M
Resolution
Maximum Pixel Clock148MHz (Analog,Digital)
Power Supply
Display area
Pixel Pitch0.2715 mm (H) x 0.2715 mm (V)
Horizontal
Frequency
Vertical
Frequency
Optimum
Resolution
Maximum
Resolution
521.28 mm (H) x 293.22 mm (V)
20.2 Inches (H) x 11.6 Inches (V)
0.011 Inches (H) x 0.011 Inches (V)
30 ~ 81 kHz
56 ~ 75 Hz
1920x1080@60Hz
1920x1080@60Hz
This product uses 100 to 240V.
Refer to the label at the back of the product as the standard voltage
can vary in different countries.
This monitor can be installed and used with any Plug-and-Play
compatible systems. Two-way data exchange between the monitor
Plug-and-Play
Panel Dots (Pixels)
The above specifications are subject to change without notice to improve quality.
This device is a Class B digital apparatus.
and PC system optimizes the monitor settings. Monitor installation
takes place automatically. However, you can customize the
installation settings if desired.
Due to the nature of the manufacturing of this product,
approximately 1 pixel per million (1ppm) may be brighter or darker on
the LCD panel. This does not affect product performance.
(USA only)
Dispose unwanted electronics through an approved recycler.
To find the nearest recycling location, go to our website:
www.samsung.com/recyclingdirect or call, (877) 278 - 0799
10 Specifications
83
Specifications
10
10.2PowerSaver
The power-saving function of this product reduces power consumption by switching off the screen and
changing the color of the power LED if the product is not used for a specified period of time. The power
is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or
move the mouse. Power-saving mode functions only when the product is connected to a PC that has a
power-saving function.
PowerSaver
Power IndicatorOnOnBlinkingOff
Power
Consumption
(S19C200NY)
Power
Consumption
(S19C200N)
Power
Consumption
(S19C200NW)
Power
Consumption
(S19C200BW)
Power
Consumption
(S19C200BR)
Normal
operation mode
Typical 19 watts13 watts
Typical 19 watts13 watts
Typical 19 watts15 watts
Typical 19 watts15 watts
Typical 19 watts16 watts
Energy Star
Power
Consumption
Power saving
mode
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Power off
(Power button)
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Power
Consumption
(S19C200NR)
Power
Consumption
(S20C200B)
Power
Consumption
(S22C200NY)
Power
Consumption
(S22C200N)
Typical 19 watts16 watts
Typical 19 watts16 watts
Typical 24 watts21 watts
cal 24 watts21 watts
i
Typ
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
10 Specifications
84
10
Specifications
PowerSaver
Power
Consumption
(S22C200B)
Power
Consumption
(S22C200BW)
Power
Consumption
(S22C210B)
Power
Consumption
(S23C200B)
Power
Consumption
(S24C200BL)
Normal
operation mode
Typical 24 watts21 watts
Typical 24 watts19 watts
Typical 24 watts21 watts
Typical 25 watts22 watts
Typical 30 watts22 watts
Energy Star
Power
Consumption
Power saving
mode
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Power off
(Power button)
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
Less than
0.1 watts
The power consumption level can vary in different operating conditions or when settings are
changed.(S**C200** Model Power saving mode / Power off (Power button) : Less than 0.1 watts
(Analog Input Condition), Max 0.25watts )
ENERGY STAR
Energy Star power is measured with the test method in the current Energy Star
To reduce the power consumption to 0 watts, turn off the power switch on the back of the product
or disconnect the power cable. Be sure to disconnect the power cable when you will not be using
the product for an extended period of time. To reduce the power consumption to 0 watts when the
power switch is not available, disconnect the power cable.
®
is a US registered mark of the United States Environmental Protection Agency.
®
Standard.
10 Specifications
85
Specifications
10
10.3Standard Signal Mode Table
This product can be set to only one resolution for each screen size to obtain the optimum picture
quality due to the nature of the panel. Therefore, a resolution other than the specified resolution
may degrade the picture quality. To avoid this, it is recommended that you select the optimum
resolution specified for the screen size of your product.
Check the frequency when you exchange a CDT monitor (connected to a PC) for an LCD monitor.
If the LCD monitor does not support 85Hz, change the vertical frequency to 60Hz using the CDT
monitor before you exchange it with the LCD monitor.
If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will
automatically be adjusted. If the signal transmitted from the PC does not belong to the standard signal
modes, the screen may be blank even though the power LED turns on. In such a case, change the
settings according to the following table by referring to the graphics card user manual.
S19C200NY
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1024 x 76856.47670.06975.000-/-
VESA, 1024 x 76860.02375.02978.750+/+
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1366 x 76847.71259.79085.500+/+
10 Specifications
86
10
Specifications
S19C200N
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
VESA, 1024 x 76856.47670.06975.000-/-
VESA, 1024 x 76860.02375.02978.750+/+
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1366 x 76847.71259.79085.500+/+
10 Specifications
87
10
Specifications
S19C200NW
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
MAC, 1152 x 87068.68175.062100.000-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
VESA, 1024 x 76856.47670.06975.000-/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1024 x 76860.02375.02978.750+/+
VESA, 1152 x 86467.50075.000108.000+/+
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1280 x 80049.70259.81083.500-/+
VESA, 1440 x 90055.93559.887106.500-/+
VESA, 1440 x 90070.63574.984136.750-/+
10 Specifications
88
10
Specifications
S19C200BW
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
MAC, 1152 x 87068.68175.062100.000-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
VESA, 1024 x 76856.47670.06975.000-/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1024 x 76860.02375.02978.750+/+
VESA, 1152 x 86467.50075.000108.000+/+
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1280 x 80049.70259.81083.500-/+
VESA, 1440 x 90055.93559.887106.500-/+
VESA, 1440 x 90070.63574.984136.750-/+
10 Specifications
89
10
Specifications
S19C200BR
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
MAC, 1152 x 87068.68175.062100.000-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
VESA, 1024 x 76856.47670.06975.000-/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1024 x 76860.02375.02978.750+/+
VESA, 1152 x 86467.50075.000108.000+/+
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1280 x 80049.70259.81083.500-/+
VESA, 1280 x 96060.00060.000108.000+/+
VESA, 1280 x 102463.98160.020108.000+/+
VESA, 1280 x 102479.97675.025135.000+/+
10 Specifications
90
10
Specifications
S19C200NR
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
MAC, 1152 x 87068.68175.062100.000-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
VESA, 1024 x 76856.47670.06975.000-/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1024 x 76860.02375.02978.750+/+
VESA, 1152 x 86467.50075.000108.000+/+
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1280 x 80049.70259.81083.500-/+
VESA, 1280 x 96060.00060.000108.000+/+
VESA, 1280 x 102463.98160.020108.000+/+
VESA, 1280 x 102479.97675.025135.000+/+
10 Specifications
91
10
Specifications
S20C200B
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
MAC, 1152 x 87068.68175.062100.000-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
VESA, 1024 x 76856.47670.06975.000-/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1024 x 76860.02375.02978.750+/+
VESA, 1152 x 86467.50075.000108.000+/+
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1280 x 80049.70259.81083.500-/+
VESA, 1440 x 90055.93559.887106.500-/+
VESA, 1440 x 90070.63574.984136.750-/+
VESA, 1600 x 90060.00060.000108.000+/+
10 Specifications
92
10
Specifications
S22C200NY
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
MAC, 1152 x 87068.68175.062100.000-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
VESA, 1024 x 76856.47670.06975.000-/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1024 x 76860.02375.02978.750+/+
VESA, 1152 x 86467.50075.000108.000+/+
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1280 x 80049.70259.81083.500-/+
VESA, 1280 x 102463.98160.020108.000+/+
VESA, 1280 x 102479.97675.025135.000+/+
VESA, 1440 x 90055.93559.887106.500-/+
VESA, 1600 x 90060.00060.000108.000+/+
VESA, 1680 x 105065.29059.954146.250-/+
VESA, 1920 x 108067.50060.000148.500+/+
10 Specifications
93
10
Specifications
S22C200N
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
MAC, 1152 x 87068.68175.062100.000-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
VESA, 1024 x 76856.47670.06975.000-/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1024 x 76860.02375.02978.750+/+
VESA, 1152 x 86467.50075.000108.000+/+
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1280 x 80049.70259.81083.500-/+
VESA, 1280 x 102463.98160.020108.000+/+
VESA, 1280 x 102479.97675.025135.000+/+
VESA, 1440 x 90055.93559.887106.500-/+
VESA, 1600 x 90060.00060.000108.000+/+
VESA, 1680 x 105065.29059.954146.250-/+
VESA, 1920 x 108067.50060.000148.500+/+
10 Specifications
94
10
Specifications
S22C200B
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
MAC, 1152 x 87068.68175.062100.000-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
VESA, 1024 x 76856.47670.06975.000-/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1024 x 76860.02375.02978.750+/+
VESA, 1152 x 86467.50075.000108.000+/+
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1280 x 80049.70259.81083.500-/+
VESA, 1280 x 102463.98160.020108.000+/+
VESA, 1280 x 102479.97675.025135.000+/+
VESA, 1440 x 90055.93559.887106.500-/+
VESA, 1600 x 90060.00060.000108.000+/+
VESA, 1680 x 105065.29059.954146.250-/+
VESA, 1920 x 108067.50060.000148.500+/+
10 Specifications
95
10
Specifications
S22C200BW
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
MAC, 1152 x 87068.68175.062100.000-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
VESA, 1024 x 76856.47670.06975.000-/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1024 x 76860.02375.02978.750+/+
VESA, 1152 x 86467.50075.000108.000+/+
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1280 x 80049.70259.81083.500-/+
VESA, 1280 x 102463.98160.020108.000+/+
VESA, 1280 x 102479.97675.025135.000+/+
VESA, 1440 x 90055.93559.887106.500-/+
VESA, 1600 x 90060.00060.000108.000+/+
VESA, 1680 x 105065.29059.954146.250-/+
10 Specifications
96
10
Specifications
S22C210B
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
MAC, 1152 x 87068.68175.062100.000-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
VESA, 1024 x 76856.47670.06975.000-/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1024 x 76860.02375.02978.750+/+
VESA, 1152 x 86467.50075.000108.000+/+
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1280 x 80049.70259.81083.500-/+
VESA, 1280 x 102463.98160.020108.000+/+
VESA, 1280 x 102479.97675.025135.000+/+
VESA, 1440 x 90055.93559.887106.500-/+
VESA, 1600 x 90060.00060.000108.000+/+
VESA, 1680 x 105065.29059.954146.250-/+
VESA, 1920 x 108067.50060.000148.500+/+
10 Specifications
97
10
Specifications
S23C200B
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
MAC, 1152 x 87068.68175.062100.000-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
VESA, 1024 x 76856.47670.06975.000-/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1024 x 76860.02375.02978.750+/+
VESA, 1152 x 86467.50075.000108.000+/+
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1280 x 80049.70259.81083.500-/+
VESA, 1280 x 102463.98160.020108.000+/+
VESA, 1280 x 102479.97675.025135.000+/+
VESA, 1440 x 90055.93559.887106.500-/+
VESA, 1600 x 90060.00060.000108.000+/+
VESA, 1680 x 105065.29059.954146.250-/+
VESA, 1920 x 108067.50060.000148.500+/+
10 Specifications
98
10
Specifications
S24C200BL
Horizontal
Resolution
IBM, 720 x 40031.46970.08728.322-/+
MAC, 640 x 48035.00066.66730.240-/-
MAC, 832 x 62449.72674.55157.284-/-
MAC, 1152 x 87068.68175.062100.000-/-
VESA, 640 x 48031.46959.94025.175-/-
VESA, 640 x 48037.86172.80931.500-/-
VESA, 640 x 48037.50075.00031.500-/-
VESA, 800 x 60035.15656.25036.000+/+
VESA, 800 x 60037.87960.31740.000+/+
VESA, 800 x 60048.07772.18850.000+/+
VESA, 800 x 60046.87575.00049.500+/+
VESA, 1024 x 76848.36360.00465.000-/-
VESA, 1024 x 76856.47670.06975.000-/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1024 x 76860.02375.02978.750+/+
VESA, 1152 x 86467.50075.000108.000+/+
VESA, 1280 x 72045.00060.00074.250+/+
VESA, 1280 x 80049.70259.81083.500-/+
VESA, 1280 x 102463.98160.020108.000+/+
VESA, 1280 x 102479.97675.025135.000+/+
VESA, 1440 x 90055.93559.887106.500-/+
VESA, 1600 x 90060.00060.000108.000+/+
VESA, 1680 x 105065.29059.954146.250-/+
VESA, 1920 x 108067.50060.000148.500+/+
Horizontal Frequency
The time required to scan a single line from the left to the right side of the screen is called a
horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency.
Horizontal frequency is measured in kHz.
Vertical Frequency
Repeating the same picture dozens of times per second allows you to view natural pictures. The
repeat frequency is called "vertical frequency" or "refresh rate" and is indicated in Hz.
10 Specifications
99
Appendix
01-8000 112 112
Bogotá: 6001272
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG