Samsung LS19GSESSY-XAA User Manual

prog

SyncMaster 916V

Install drivers Install

rams

Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

Power

When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.

Do not use a damaged or loose plug.

z This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

This may cause an electric shock or fire.

Use only a properly grounded plug and receptacle.

An improper ground may cause electric shock or equipment damage.

Insert the power plug firmly so that it does not come loose.

A bad connection may cause fire.

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

This may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet.

Installation

z This may cause fire.

Be sure to contact an authorized service center, when installing your monitor in a location with the heavy dust, high or low temperatures, high humidity, chemical substance and where it operates for 24 hours such as the airport, the train station or etc.

Failure to do so may cause a serious damage to your monitor.

Put your monitor in a location with low humidity and a minimum of dust.

Failure to do so may cause an electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

z This may cause damage to the product or human body.

Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf.

Dropping the product may cause damage to the product or personal injury.

Do not place the product on an unstable or small surface area.

Place the product on an even, stable surface, as the product may fall and

cause harm to someone walking by, specifically children.

Do not place the product on the floor.

Someone, specifically children could trip over it.

Keep any flammable objects such as candles, insecticides or cigarettes away from the product.

Otherwise, this may cause a fire.

Keep any heating devices away from the power cable.

A melted coating may lead to electric shock or fire.

Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc.

Any increase in internal temperature may cause fire.

Set down the monitor carefully.

The monitor could be damaged or broken.

Do not place the monitor face down.

The TFT-LCD surface may be damaged.

Installing a wall bracket must be done by a qualified professional.

Clean

z Installation by unqualified personnel may result in injury.

Always use the mounting device specified in the owner's manual.

When installing the product, make sure to keep it away from the wall (more than 10cm/4inch ) for ventilation purposes.

Poor ventilation may cause an increase in the internal temperature of the

product, resulting in a shortened component life and degraded performance.

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.

Do not spray water or detergent directly on the monitor.

This may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.

A dirty connector may cause an electric shock or fire.

Make sure to unplug the power cord before cleaning the product.

Otherwise, this may cause electric shock or fire.

Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.

Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide,

air freshener, lubricant or detergent.

Others

Contact the Service Center or Customer Center for interior cleaning once a year.

Keep the product's interior clean. Dust which has accumulated in the interior

over an extended period of time may cause malfunction or fire.

Do not remove cover (or back).

This may cause an electric shock or fire.

Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact

an authorized dealer or service.

This may cause an electric shock or fire.

Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle.

This may cause malfunction, an electric shock or fire.

Especially avoid operating the monitor near water or outdoors where it could be

exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center .

z The monitor may malfunction, causing an electric shock or fire.

Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time.

Failure to do so may cause an electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not cover the vents on the monitor cabinet.

Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects on the monitor.

This may cause malfunction, an electric shock or fire.

z If a foreign substance enters the monitor, unplug the power cord and contact

the Service Center.

Keep the product away from combustible chemical sprays or inflammable substances.

This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

This may cause an electric shock, fire or injury.

Do not insert metal objects such as chopsticks, wire and gimlet or inflammable objects such as paper and match into the vent, headphone port or AV ports.

It may cause a fire or an electric shock. If an alien substances or water flows

into the product, turn the product off, unplug the power connector from the wall outlet and contact service center.

If you view a fixed screen for an extended period of time, residual image or blurriness may appear.

Change the mode to energy save or set a screensaver to moving picture when

you need to be away from the monitor for an extended period of time.

Adjust the resolution and frequency to the levels appropriate for the model.

z Inappropriate resolution may cause undesirable picture quality.

19 inch - 1280 X 1024

Watching the monitor continuously at a too close angle may result in eyesight damage.

To ease eye strain, take at least a five-minute break after every hour of using the monitor

Do not install the product on an unstable, uneven surface or a location prone to vibrations.

Dropping the product may cause damage to the product or personal injury.

Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire.

When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connecting to other devices, are disconnected before moving the monitor.

z Failure to disconnect cables may damage it and lead to fire or an electric

shock.

Place the product out of children’s reach, as they could damage it by hanging onto it.

A falling product could cause physical damage even death .

When not using the product for an extended time period, keep the product unplugged.

z Otherwise, this may cause heat emission from the accumulated dirt or

degraded insulation, leading to electric shock or fire.

Do not place children’s favorite objects (or anything else that may be tempting) on the product.

Children may try to climb on the product to retrieve an object. The product

could fall, causing physical damage or even death.

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local deale

to buy optional items.

Unpacking

Monitor

Manual

Quick Setup Guide

Monito

Warranty Card

(Not available in all locations)

Bottom Hanger

User's Guide,

Monitor Driver,

Natural Color software,

icTune™ software

Cable

D-Sub Cable Power Cord

Front

MENU button [ ]

MagicBright™ button [ ]

Power button [ ] /

Power indicator

Brightness button [ ]

Adjust buttons [ ]

Enter button [ ]/ AUTO button

Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu.

MagicBright™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Text, Internet, and Entertain. Each mode has its own pre-configured brightness value. You can easily select one of four settings by simply pressing MagicBright™ control button.

1) Custom

Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.

2) Text

For documentations or works involving heavy text.

3) Internet

For working with a mixture of images such as text and graphics.

4) Entertain

For watching motion pictures such as a DVD or VCD.

>>Click here to see an animation clip

Use this button for turn the monitor on and off./

This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.

When OSD is not on the screen, push the button to adjust brightness.

Use this button for navigate and select menus or adjust the menu items in the menu screen.

Activates a highlighted menu item. / Use this button for auto adjustment.

: Normal brightness

: Medium brightness

: High brightness

Rear

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Power port

D-sub 15-pin port

Kensington Lock

(The configuration at the back of the monitor may vary from product to product.)

Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately. )

For usin

See Connecting the Monitor for further information regarding cable connections.

a locking device, contact where you purchase it.

Connecting the Monitor

2-1.

2-2.

2-3.

Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.

Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-SUB connection cable.

In the case of an old model Macintosh, you need to connect the monitor using a special Mac adapter.

Turn on your computer and monitor. If your monitor displays an image, installation is complete.

Using the Stand

Monitor Assembly

1. Monitor and Bottom

2. Monitor and Hanger

Attaching a Base

This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.

A. Monitor B. Mounting interface pad

. Turn off your monitor and unplug its power cord.

. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.

. Remove four screwsand then remove the stand from the LCD monitor.

lign the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four

screws that came with the arm-type base, wall mount hanger or other base.

Installing the Monitor Driver (Automatic)

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

Internet web site : http://www.samsung.com/ (Worldwide)

Windows XP/2000

http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea)

http://www.samsungmonitor.com.cn/ (China)

1. Insert CD into the CD-ROM drive.

2. Click

"Windows XP/2000 Driver"

3. Choose your monitor model in the model list, then click the

"OK"

button.

4. If you can see following message window, then click the click

"OK"

button.

This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor homepage

http://www.samsung.com/.

5. Monitor driver installation is completed.

Installing the Monitor Driver (Manual)

"Continue Anyway"

button. Then

Prepare a blank disk and download the driver program file at the Internet web site shown here.

Internet web site : http://www.samsung.com/ (Worldwide)

http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

Microsoft® Windows® XP Operating System

1. Insert CD into the CD-ROM driver.

2. Click "

Start

" —> "

Control Panel

" then click the "

Windows XP | Windows 2000 | Windows NT | Linux

Appearance and Themes

" Icon.

3. Click "

" icon and choose the "

Display

Settings

" tab then click "

Advanced..

4. Click the "

5. Click "

Update Driver..

Properties

" button on the "

" and select "

" tab and select "

Monitor

Install from a list or..

Driver

" then click "

" tab.

" button.

6. Select "

Don't search ,I will..

" then click "

" and then click "

Have disk

7. Click the " and click the "

" button then choose A:(D:\Driver) and choose your monitor model in the model list

Browse

" button.

8. If you can see following "

Message

" window, then click the "

Continue Anyway

" button. Then click

"OK" button.

This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage.

http://www.samsung.com/

9. Click the "

" button then click "OK" button continually.

10. Monitor driver installation is completed.

Microsoft

Windows® 2000 Operating System

When you can see "Digital Signature Not Found" on your monitor, follow these steps.

1. Choose "OK" button on the "

2. Click the "

Browse

" button on the "

Insert disk

" window.

File Needed

" window.

3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.

How to install

1. Click "

2. Double click the "

3. Choose the "

4. Choose "

Start

" , "

Setting

Settings

Monitor

" , "

Control Panel

" Icon.

Display

" tab and then click "

Advanced..

Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please

stop installation

Case2: If the "Properties" button is active, click the "Properties" button then follow next steps

continually.

5. Click "

6. Choose "

driver

7. Click the "

8. Click the "

9. Choose your monitor model and click the "

10. Click the "

" and then click on "

Driver

Update Driver..

" then click on the "Next" button.

Display a list of the known drivers for this device so that I can choose a specific

" then click "

Browse Open

Finish

" and then click "

Have disk

" button then choose A:(D:\Driver).

" button, then click "OK" button.

" button then the "

" button.

" button then click "

" button.

If you can see the " the "

" button then the "

Finish

Digital Signature Not Found

" button.

" window then click the "

"button. And click

Yes

Microsoft

1. Click

2. In Display Registration Information window, click Settings Tab and then click

Windows® NT Operating System

Start, Settings, Control Panel

, and then double-click

Display

icon.

All Display Modes

3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK.

4. Click

button if you see the screen working normally after clicking

Apply

. If the screen is not

Test

normal, change to a different mode (lower mode of resolution, colors or frequency).

If there is no Mode at

All Display Modes

, select the level of resolution and vertical frequency

by referring to the Preset Timing Modes in the user guide.

Linux Operating System

To execute X-Window, you need to make the X86Config file, which is a type of system setting file.

1. Press Enter at the first and the second screen after executing the X86Config file.

2. The third screen is for

setting your mouse

3. Set a mouse for your computer.

4. The next screen is for

selecting a keyboard

5. Set a Keyboard for your computer.

6. The next screen is for

7. First of all, set a

8. Set a

vertical frequency

9. Enter the

horizontal frequency

model name of your monitor

setting your monitor

for your monitor. (You can enter the frequency directly.)

. This information will not affect the actual execution of X-

Window.

10. You have

Execute

finished

X-Window after setting other requested hardware.

setting up your monitor.

Natural Color

Natural Color Software Program

One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI). This system is available only for Samsung monitors and makes the color of the images on the monitor the same as the printed or scanned images. For more information, refer to Help (F1) in the software program.

How to install the Natural Color software

Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program Natural Color will be executed. Click Natural Color on the initial screen to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM Drive, click the [Start] button of Windows and then select [Execute]. Enter D:\color\eng\setup.exe and then press the <Enter> key. (If the drive where the CD is inserted is not D:\, enter the applicable drive.)

How to delete the Natural Color software program

Select

"Setting/Control Panel"

Select Natural Color from the list and then click the

on the

menu and then double-click

"Start"

"Add/Delete"

button.

"Add/Delete a program"

+ 42 hidden pages