Samsung LS15E33C, LS17E34C Schematic

TFT-LCD MONITOR

Chassis Model
AS15SO LS15E33C
AS17SO LS17E34C

Manual

SERVICE

TFT-LCD MONITOR CONTENTS

1. Precautions

2. Product Specifications

3. Disassembly & Reassembly

4. Alignment & Adjustments

5. Troubleshooting

6. Exploded View & Parts List

7. Electrical Parts List

8. Block Diagram

9. Wiring Diagram

10. PCB Layout

11. Schematic Diagrams

12. Panel Description

❈ This Service Manual is a property of Samsung Electronics Co., Ltd.

Any unauthorized use of Manual can be punished under applicable
International and/or domestic law.

Samsung Electronics Co.,Ltd.

416, Maetan-3Dong, Paldal-Gu, Suwon City, Kyungki-Do, Korea, 442-742
Printed in Korea
P/N : BN82-00098C-00
URL : http://ecms. samsungelectronics. com/

1-1-1 Warnings

1. For continued safety, do not attempt to modify the
circuit board.

2. Disconnect the AC power and DC Power Jack
before servicing.

1-1-2 Servicing the LCD Monitor

1. When servicing the LCD Monitor disconnect the
AC line cord from the AC outlet.

2. It is essential that service technicians have an
accurate voltage meter available at all times. Check
the calibration of this meter periodically.

1-1-3 Fire and Shock Hazard

Before returning the monitor to the user, perform the
following safety checks:

1. Inspect each lead dress to make certain that the
leads are not pinched or that hardware is not
lodged between the chassis and other metal parts in
the monitor.

2. Inspect all protective devices such as nonmetallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators, etc.

3. Leakage Current Hot Check (Figure 1-1):

WARNING: Do not use an isolation transformer during

this test.

Use a leakage current tester or a metering system
that complies with American National Standards
Institute (ANSI C101.1, Leakage Current for

Appliances), and Underwriters Laboratories (UL
Publication UL1410, 59.7).

Figure 1-1. Leakage Current Test Circuit

4. With the unit completely reassembled, plug the AC
line cord directly into a 120V AC outlet. With the
unit’s AC switch first in the ON position and then
OFF, measure the current between a known earth
ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including: metal cabinets,
screwheads and control shafts. The current
measured should not exceed 0.5 milliamp. Reverse
the power-plug prongs in the AC outlet and repeat

the test.

1-1-4 Product Safety Notices

Some electrical and mechanical parts have special
safety-related characteristics which are often not
evident from visual inspection. The protection they give
may not be obtained by replacing them with
components rated for higher voltage, wattage, etc. Parts
that have special safety characteristics are identified by

on schematics and parts lists. A substitute
replacement that does not have the same safety
characteristics as the recommended replacement part
might create shock, fire and/or other hazards. Product
safety is under review continuously and new
instructions are issued whenever appropriate.

LS15E33C/LS17E34C 1-1

1 Precautions

Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as
electrical shock.

1-1 Safety Precautions

DEVICE
UNDER
TEST

TEST ALL

EXPOSED METAL

SURFACES

(READING SHOULD

NOT BE ABOVE 0.5mA)

LEAKAGE
CURRENT

TESTER

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)

EARTH

GROUND

!

1-2-1 General Servicing Precautions

1. Always unplug the unit’s AC power cord from the
AC power source and disconnect the DC Power
Jack before attempting to:
(a) remove or reinstall any component or assembly,
(b) disconnect PCB plugs or connectors, (c) connect
a test component in parallel with an electrolytic
capacitor.

2. Some components are raised above the printed
circuit board for safety. An insulation tube or tape
is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.

3. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the area around the
serviced part has not been damaged.

1. Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known earth
ground. Alternatively, wear a discharging wrist­strap device. To avoid a shock hazard, be sure to
remove the wrist strap before applying power to
the monitor.

2. After removing an ESD-equipped assembly, place it
on a conductive surface such as aluminum foil to
prevent accumulation of an electrostatic charge.

3. Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage
ESDs.

4. Use only a grounded-tip soldering iron to solder or
desolder ESDs.

5. Use only an anti-static solder removal device. Some
solder removal devices not classified as “anti-static”
can generate electrical charges sufficient to damage
ESDs.

4. Check the insulation between the blades of the AC
plug and accessible conductive parts (examples:
metal panels, input terminals and earphone jacks).

5. Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the power
switch ON. Connect an insulation resistance meter
(500 V) to the blades of the AC plug.

The insulation resistance between each blade of the
AC plug and accessible conductive parts (see
above) should be greater than 1 megohm.

6. Always connect a test instrument’s ground lead to
the instrument chassis ground before connecting
the positive lead; always remove the instrument’s
ground lead last.

6. Do not remove a replacement ESD from its
protective package until you are ready to install it.
Most replacement ESDs are packaged with leads
that are electrically shorted together by conductive
foam, aluminum foil or other conductive materials.

7. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.

Caution: Be sure no power is applied to the

chassis or circuit and observe all
other safety precautions.

8. Minimize body motions when handling
unpackaged replacement ESDs. Motions such as
brushing clothes together, or lifting your foot from
a carpeted floor can generate enough static
electricity to damage an ESD.

1 Precautions

1-2 LS15E33C/LS17E34C

1-3 Electrostatically Sensitive Devices (ESD) Precautions

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly
called Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect
transistors. The following techniques will reduce the incidence of component damage caused by static electricity.

1-2 Servicing Precautions

WARNING: An electrolytic capacitor installed with the wrong polarity might explode.
Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions

section of this manual.

Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the

safety precautions, always follow the safety precautions.

2 Product Specifications

2-1 Specifications

LCD Panel TFT-LCD panel, RGB vertical stripe, normally TFT-LCD panel, RGB vertical stripe, normally

white, 15-Inch viewable, 0.297 mm pixel pitch white, 17-Inch viewable, 0.264 mm pixel pitch

Scanning Frequency Horizontal : 30 kHz ~ 69 kHz (Automatic) 30 kHz ~ 81 kHz (Automatic)

Vertical : 56 Hz ~ 75 Hz (Automatic) 56 Hz ~ 75 Hz (Automatic)
Display Colors 16.7 Million colors
Maximum Resolution Horizontal : 1024 Pixels 1280 Pixels

Vertical : 768 Pixels 1024 Pixels
Input Video Signal Analog 0.7 Vp-p ± 5% positive at 75 Ω, internally terminated
Input Sync Signal Type : Separate H/V, automatic synchronization without external switch of sync type

Level : TTL level
Maximum Pixel Clock rate 95 MHz 135 MHz
Active Display

Horizontal/Vertical
AC power voltage & Frequency

AC 90 ~ 264 Volts, 60 / 50 Hz ± 3 Hz
Power Consumption 48 W (Max), (2W Power surge) 58 W (Max), (2W Power surge)
Dimensions (W x D x H)

Set

18.2 x 7.2 x 12.8 Inches (460.9 x 182.2 x 325.1 mm) After installation of stand 20.3 x 7.1 x 14.6 Inches (514.6 x 180.9 x 371.3 mm) After installation of stand

18.1 x 3.4 x 12.2 Inches (460.9 x 87.6 x 305.5 mm) Without stand 21.3 x 3.5 x 13.8 Inches (514.6 x 89.0 x 351.1 mm) Without stand

Package 21.1 x 16.9 x 6.9 Inches (535 x 429 x 175 mm) 23.3 x 18.6 x 6.9 Inches (593 x 473 x 175 mm)
Set Weight 3.9 Kg (8.6 Ibs) / 3.4 Kg (7.5 Ibs) 5.0 Kg (11.0 Ibs) / 4.5 Kg (9.9 Ibs)

Package Weight 6.2 Kg (13.7 Ibs) 6.8 Kg (15.0 Ibs)
Environmental Considerations Operating Temperature : 50 °F ~ 104 °F (10 °C ~ 40 °C)

Operating Humidity : 10 % ~ 80 %

Storage Temperature : -13 °F ~ 113 °F (-25 °C ~ 45 °C)

Storage Humidity : 5 % ~ 95 %

TV System

Antenna Input 75Ω, Coaxial Cable

– MAX internal speaker Out : Right => 3W, Left => 3W
Sound Characteristic

– BASS Control Range : -12dB~ + 12dB

– TREBLE Control Range : -12dB~ + 12dB

– Headphone Out: RF => 5mW max (400m Vrms)

A/V => 10mW max (580 Vrms), Max input sound: -9 dBm

– Output Frequency : RF => 80 Hz ~ 15 kHz

A/V => 80 Hz ~ 20 kHz

LS15E33C/LS17E34C 2-1

Item

Description

LS15E33C LS17E34C

304.1 mm / 228.1 mm 338.1 mm / 270.1 mm

Tuning Frequency Synthesize

Color PAL, NTSC, SECAM

Sound BTSC, ECJ, KOREA

2 Product Specifications

2-2 LS15E33C/LS17E34C

2-2 Pin Assignments

Sync
Type

Pin No.

Separate H/V Composite H/V

Sync-on-green

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15

Red
Green
Blue
GND
GND (DDC Return)
GND-Red
GND-Green
GND-Blue
No Connection
GND-Sync./Self Test
GND
DDC Data
Horizontal sync.
Vertical sync.
DDC Clock

Red
Green
Blue
GND
GND (DDC Return)
GND-Red
GND-Green
GND-Blue
No Connection
GND-Sync./Self Test
GND
DDC Data
H/V-Sync.
Not Used
DDC Clock

Red
Green + H/V Sync.
Blue
GND
GND (DDC Return)
GND-Red
GND-Green
GND-Blue
Not Used
GND-Sync./Self Test
GND
DDC Data
Not Used
Not Used
DDC Clock

2 Product Specifications

LS15E33C/LS17E34C 2-3

QRS

P

O

Video

Sync

Sync

Horizontal

Vertical

CDE

P

O

B

A

Video

Sync

Sync

Separate Sync

2-3 Timing Chart

This section of the service manual describes the timing that the computer industry recognizes as standard
for computer-generated video signals.

C D

A

O

E

B

P

Video

Sync

Sync

Video

Q R S

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
C : Back porch D : Active time Q : Back porch R : Active time
E : Front porch S : Front porch

VIDEO

A

B

O

P

Q

R

S

Horizontal

Vertical

H/V Composite Sync

Sync-on-Green

79.976

12.504

1.067

1.837

9.481

0.119

75.025

13.329

0.038

0.475

12.804

0.013

135.000

Positive
Positive

Separate

1280/75Hz
1280x1024

1024/75Hz

1024 x 768

60.023

16.660

1.219

2.235

13.003

0.203

75.029

13.328

0.050

0.466

12.795

0.017

78.750

Positive
Positive

Separate

31.469

31.777

3.813

1.589

26.058

0.318

70.087

14.268

0.064

0.858

13.155

0.191

28.322

Negative

Positive

Separate

fH (KHz)
A µsec
B µsec
C µsec
D µsec
E µsec
fV (Hz)
O msec
P msec
Q msec
R msec
S msec
Clock

Freq.
(MHz)

Polarity
H.Sync

V.Sync
Remark

IBM

640/75 Hz
640 x 480

800/75 Hz
800 x 600

1024/60Hz

1024 x 768

VGA2/

70 Hz

720 x 400

VGA3/

60 Hz

640 x 480

Table 2-1 Timing Chart

31.469

31.778

3.813

1.589

26.058

0.318

59.940

16.683

0.064

0.794

15.761

0.064

25.175

Negative
Negative
Separate

37.500

26.667

2.032

3.810

20.317

0.508

75.000

13.333

0.080

0.427

12.800

0.027

31.500

Negative
Negative
Separate

46.875

21.333

1.616

3.232

16.162

0.323

75.000

13.333

0.064

0.448

12.800

0.021

49.500

Positive
Positive

Separate

48.363

20.677

2.092

2.462

15.754

0.369

60.004

16.666

0.124

0.600

15.880

0.062

75.000

Negative
Negative
Separate

Mode

VESA

Timing

(17” Only)

Green

Horizontal

B

Vertical

P

Q

R

O

S

LS15E33C/LS17E34C 3-1

3 Disassembly and Reassembly

This section of the service manual describes the disassembly and reassembly procedures for the
LS15E33C/LS17E34C monitor.

WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling

these components.

3-1 Disassembly

Cautions : 1. Disconnect the monitor from the power source before disassembly.

2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.

3. R/Cover opening jig : BH81-00001A

3-1-1 LS15E33C

1. Loacte the monitor on the cushioned table
with face down. Remove the stand from LCD­TV and pull the rear cover by pressing a hand.

2. Remove power cable on the hand and signal
cable on the driver.

3. Remove 2 screws on the rear cover and
remove the rear cover by using opening jig.

4. Open the rear cover and remove 6 screws
from the holder.

5. Disconnect ass’y shield PCB cable and
inverter cable from the shield.
(see illustrations)

3 Disassembly and Reassembly

3-2 LS15E33C/LS17E34C

6. Remove 2 screws from the shield.
Disconnect IR PCB cable. (see illustrations)

7. Lift up the shield D-SUB.
Disconnect LVDS cable. (see illustrations)

8. Lift up the panel. (see illustrations)

1. Loacte the monitor on the cushioned table
with face down. Remove the stand from LCD­TV and pull the rear cover by pressing a hand.

2. Remove power cable on the hand and signal
cable on the driver.

3. Remove 2 screws on the rear cover and
remove the rear cover by using opening jig.

3-1-2 LS17E34C

3 Disassembly and Reassembly

LS15E33C/LS17E34C 3-3

4. Open the rear cover and remove 8 screws
from the shield.

5. Disconnect cable and inverter cable from the
shield. (see illustrations)

6. Remove 6 screws from the shield.
(see illustrations)

7. Remove IR PCB cable from the shield and lift
up the shield. (see illustrations)

8. Remove LVDS cable from the main shield and
lift up the panel. (see illustrations)

9. Remove the panel.

LS15E33C/LS17E34C 4-1

4 Alignments and Adjustments

4-1 General Alignment Instruction

1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation.
Check the basic characteristics such as height, horizontal and vertical sync.

2. Use the specified test equipment or its equivalent.

3. Correct impedance matching is essential.

4. Avoid overload. Excessive signal from a sweep generator might overload the front-end
of the TV. When inserting signal markers, do not allow the marker generator to distort
test results.

5. Connect the TV only to an DC power source with voltage and frequency as specified on
the backcover nameplate.

6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure
that the power cord is disconnected before replacing any parts.

7. To protect aganist shock hazard, use an isolation transformer.

4-2 Adjustment Instruction

4-2-1 Service Mode Screen

1. Adjustment

2. Options

3. Auto Color

4. Check sum

5. Reset

4-2-2 Service function

1. EEPROM Clear : Initially executed when replacing OTP.

2. TV Auto Color : Used to adjust TV image color.

3. PC Auto Color : Used to adjust PC image color.

4. Reset : Used after all adjustments.

5. Other functions shown are not service related.

4-2-3 Adjustment Sequence for ROM change only

4 Alignments and Adjustments

4-2 LS15E33C/LS17E34C

RGB Contrast 24
RGB Bright d3
R Gain d
G Gain d
B Gain d
FB Gain d

Help Osd : on
TTX List : off
High D : on
Channel Table
Eeprom Clear

Auto color (PC)
Auto color (TV)

EEPROM Clear TV auto color PC auto color RESET

(For ROM

change only)

LS15E33C/LS17E34C 5-1

5 Troubleshooting

5-1 No Power

Does proper DC 14 V appear at

DC jack connected to CN12?

Check SMPS PCB and adapter.

Yes

No

Does proper DC 5 V appear at

Pin 4 of IC11?

Check IC11.

Check IC23.

Yes

No

Does proper DC 14V appear at

Pin 1 of IC11?

Check IC11.

Yes

No

Does proper DC 3.3 V appear at

Pin 3 of IC14?

Check IC14.

Yes

Yes

No

Does proper DC 2.5 V appear at

Pin 4 of IC109 and IC17?

Check IC109 and IC17.

No

5 Troubleshooting

5-2 LS15E33C/LS17E34C

5-2 No Video (PC Signal)

Power indicator is green.

Does the signal appear

at C134, C135, C136

of R, G, B input?

Check CN11.

Yes

Yes

No

Does the clock pulse

appear at X21?

Check X21 and related circuit of X21.

Yes

No

Does the clock pulse appear at

output of <RA35~RA39, RA310>15”

<RA35~RA39, RA310,

RA313~318>17”?

Check related circuit of IC32.

Yes

No

Does the clock pulse appear at

output of <R611~R620>15”

<R611~R620, R61~R69, R610>17”?

Check related circuit of IC61, IC62.

Yes

No

Replace LCD panel.

5 Troubleshooting

LS15E33C/LS17E34C 5-3

Does signal appear at

<RA35~RA39, RA310>15”

<RA35~RA39, RA310, RA313~RA318>17”

of related IC32?

Check IC32 and related circuit.

Yes

No

Check IC61, 62 and

<R611, 612, ~R620>15”

<R611, 612, ~R620, R61~R69, R610>17”.

5-3 No Picture (TV, Video, S-Video)

Check Pin 55, 56 (S-Video)

and Pin 52 (VCR) and Pin 74

and Pin 53 (RF-CVBS)

of IC401 (VSP9407)?

Check CN41 (Tuner) and

CN26 (VCR connector).

Yes

No

Does the signal

appear at RA33, RA34?

Check IC401 (VSP9407)

and related circuit.

Yes

No

5 Troubleshooting

5-4 LS15E33C/LS17E34C

Does the signal appear at

Pin 67 (Tuner sound signal) and Pin

57, 56 (PC sound) and Pin 51, 50 (VCR

sound) and Pin 53,54(component) of

IC53 (MSP3411G)?

Check CN51 (PC conector)

and CN26(VCR connector) and

CN25(component connector).

Yes

No

Does the signal appear at Pin 27,

28 of IC53 (MSP3411G)?

Check IC32 and related circuit.

Yes

No

Does the signal appear

at L53~L56?

Check IC55 (Audio amp) and related circuit.

Yes

No

Replace the speaker.

5-4 No Sound

6 Exploded View and Parts List

❈ You can search for updated part codes through CMS web site.

URL : http://ecms. samsungelectronics. com/

6-1 LS15E33C

LS15E33C/LS17E34C 6-1

6 Exploded View & Parts List

6-2 LS15E33C/LS17E34C

6-2 LS17E34C

BD28 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD29 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD41 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD42 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD43 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD44 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD51 3301-001145 CORE-FERRITE BEAD AB,4.5x1.6x1.6mm,-,- SNA
BD52 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
C11 2402-001081 C-AL,SMD 100uF,20%,25V,WT,TP,8.3x8.3x10
C110 2402-001042 C-AL,SMD 100uF,20%,16V,GP,TP,6.6x6.6x5.4mm
C112 2402-001086 C-AL,SMD 100UF,20%,16V,WT,TP,6.6X6.6X5.3
C113 2402-001042 C-AL,SMD 100uF,20%,16V,GP,TP,6.6x6.6x5.4mm
C114 2402-001086 C-AL,SMD 100UF,20%,16V,WT,TP,6.6X6.6X5.3
C119 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C12 2402-001081 C-AL,SMD 100uF,20%,25V,WT,TP,8.3x8.3x10
C120 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C121 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C122 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C123 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C125 2203-000697 C-CERAMIC,CHIP 0.002NF,0.25PF,50V,C0G,TP,1608
C126 2203-000697 C-CERAMIC,CHIP 0.002NF,0.25PF,50V,C0G,TP,1608
C127 2203-000697 C-CERAMIC,CHIP 0.002NF,0.25PF,50V,C0G,TP,1608
C13 2402-001044 C-AL,SMD 100UF,20%,25V,GP,TP,8.3X8.3X6.3MM
C131 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C132 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C133 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C134 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C135 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C136 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C137 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C138 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C139 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C14 2402-001044 C-AL,SMD 100UF,20%,25V,GP,TP,8.3X8.3X6.3MM
C140 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C141 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C142 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C143 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C144 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C145 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C146 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C147 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C148 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C15 2402-001086 C-AL,SMD 100UF,20%,16V,WT,TP,6.6X6.6X5.3
C150 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C154 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C155 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C156 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C157 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C158 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C159 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C160 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C162 2203-001155 C-CERAMIC,CHIP 0.068nF,5%,50V,NP0,TP,1608
C163 2203-000236 C-CERAMIC,CHIP 0.1NF,5%,50V,C0G,TP,1608
C17 2402-001042 C-AL,SMD 100uF,20%,16V,GP,TP,6.6x6.6x5.4mm
C18 2402-001042 C-AL,SMD 100uF,20%,16V,GP,TP,6.6x6.6x5.4mm
C19 2402-001042 C-AL,SMD 100uF,20%,16V,GP,TP,6.6x6.6x5.4mm
C21 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C210 2203-001417 C-CERAMIC,CHIP 0.036nF,5%,50V,NP0,TP,1608
C211 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C212 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C213 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C214 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C215 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C216 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C217 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,

7 Electrical Parts List

7-2 LS15E33C/LS17E34C

Loc. No. Code No. Description Specification Remarks

C218 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C219 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C22 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C220 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C221 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C222 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C223 2203-000784 C-CERAMIC,CHIP 0.33NF,5%,50V,C0G,TP,2012
C224 2203-000784 C-CERAMIC,CHIP 0.33NF,5%,50V,C0G,TP,2012
C225 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C226 2203-000236 C-CERAMIC,CHIP 0.1NF,5%,50V,C0G,TP,1608
C227 2203-000236 C-CERAMIC,CHIP 0.1NF,5%,50V,C0G,TP,1608
C228 2203-000236 C-CERAMIC,CHIP 0.1NF,5%,50V,C0G,TP,1608
C229 2203-000236 C-CERAMIC,CHIP 0.1NF,5%,50V,C0G,TP,1608
C23 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C230 2203-000236 C-CERAMIC,CHIP 0.1NF,5%,50V,C0G,TP,1608
C231 2203-000236 C-CERAMIC,CHIP 0.1NF,5%,50V,C0G,TP,1608
C232 2203-000236 C-CERAMIC,CHIP 0.1NF,5%,50V,C0G,TP,1608
C233 2203-000236 C-CERAMIC,CHIP 0.1NF,5%,50V,C0G,TP,1608
C234 2203-000236 C-CERAMIC,CHIP 0.1NF,5%,50V,C0G,TP,1608
C24 2402-001042 C-AL,SMD 100uF,20%,16V,GP,TP,6.6x6.6x5.4mm
C25 2402-001006 C-AL,SMD 4.7uF,20%,25V,GP,TP,3.6x6.3x3.
C26 2402-001006 C-AL,SMD 4.7uF,20%,25V,GP,TP,3.6x6.3x3.
C27 2203-001077 C-CERAMIC,CHIP 0.056nF,5%,50V,NP0,TP,2012
C28 2203-001077 C-CERAMIC,CHIP 0.056nF,5%,50V,NP0,TP,2012
C29 2203-001417 C-CERAMIC,CHIP 0.036nF,5%,50V,NP0,TP,1608
C31 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C314 2402-001006 C-AL,SMD 4.7uF,20%,25V,GP,TP,3.6x6.3x3.
C315 2402-001006 C-AL,SMD 4.7uF,20%,25V,GP,TP,3.6x6.3x3.
C317 2402-000108 C-AL,SMD 10uF,20%,16V,WT,TP,4.3x4.3x5.4
C318 2402-000179 C-AL,SMD 47uF,20%,16V,GP,TP,6.6x6.6x5.4
C319 2402-000179 C-AL,SMD 47uF,20%,16V,GP,TP,6.6x6.6x5.4
C32 2203-000697 C-CERAMIC,CHIP 0.002NF,0.25PF,50V,C0G,TP,1608
C321 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C3246 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C329 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C33 2203-000697 C-CERAMIC,CHIP 0.002NF,0.25PF,50V,C0G,TP,1608
C330 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C3300 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C331 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C332 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C333 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C334 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C335 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C336 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C337 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C338 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C339 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C3390 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C34 2203-000697 C-CERAMIC,CHIP 0.002NF,0.25PF,50V,C0G,TP,1608
C340 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C341 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C342 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C343 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C344 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C345 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C346 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C347 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C348 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C349 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C35 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C350 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C351 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C352 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C353 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C354 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,

7 Electrical Parts List

LS15E33C/LS17E34C 7-3

Loc. No. Code No. Description Specification Remarks

C355 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C3552 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C356 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C357 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C358 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C359 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C36 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C360 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C361 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C362 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C363 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C365 2203-000440 C-CERAMIC,CHIP 1nF,10%,50V,X7R,TP,1608,­C366 2203-000440 C-CERAMIC,CHIP 1nF,10%,50V,X7R,TP,1608,­C367 2203-000440 C-CERAMIC,CHIP 1nF,10%,50V,X7R,TP,1608,­C368 2203-000440 C-CERAMIC,CHIP 1nF,10%,50V,X7R,TP,1608,­C3688 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C369 2203-000440 C-CERAMIC,CHIP 1nF,10%,50V,X7R,TP,1608,­C37 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C370 2203-000440 C-CERAMIC,CHIP 1nF,10%,50V,X7R,TP,1608,­C372 2203-005005 C-CERAMIC,CHIP 100nF,10%,16V,X7R,TP,1608
C373 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C374 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C375 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C376 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C3782 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C383 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C384 2203-000384 C-CERAMIC,CHIP 0.015NF,5%,50V,C0G,TP,1608
C3890 2402-000144 C-AL,SMD 3.3uF,20%,50V,GP,TP,4.3x4.3x5.
C39 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C41 2203-000903 C-CERAMIC,CHIP 0.0047NF,0.25PF,50V,C0G,TP,1608
C410 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C411 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C412 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C413 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C414 2203-002793 C-CERAMIC,CHIP 1000nF,+80-20%,25V,Y5V,TP,2012
C415 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C416 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C417 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C418 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C4186 2402-001042 C-AL,SMD 100uF,20%,16V,GP,TP,6.6x6.6x5.4mm
C419 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C42 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C420 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C424 2203-000440 C-CERAMIC,CHIP 1nF,10%,50V,X7R,TP,1608,­C426 2203-000784 C-CERAMIC,CHIP 0.33NF,5%,50V,C0G,TP,2012
C427 2203-000236 C-CERAMIC,CHIP 0.1NF,5%,50V,C0G,TP,1608
C428 2203-000236 C-CERAMIC,CHIP 0.1NF,5%,50V,C0G,TP,1608
C43 2203-000972 C-CERAMIC,CHIP 47nF,10%,16V,X7R,TP,1608
C430 2203-000280 C-CERAMIC,CHIP 0.01NF,0.5PF,50V,C0G,TP,1608
C431 2203-000998 C-CERAMIC,CHIP 0.047NF,5%,50V,C0G,TP,1608
C432 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C433 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C434 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C437 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C438 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C439 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C44 2203-000972 C-CERAMIC,CHIP 47nF,10%,16V,X7R,TP,1608
C441 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C442 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C443 2203-000552 C-CERAMIC,CHIP 0.02NF,5%,50V,C0G,TP,1608
C444 2203-000552 C-CERAMIC,CHIP 0.02NF,5%,50V,C0G,TP,1608
C445 2203-000626 C-CERAMIC,CHIP 0.022NF,5%,50V,C0G,TP,1608
C446 2203-000626 C-CERAMIC,CHIP 0.022NF,5%,50V,C0G,TP,1608
C4482 2203-000236 C-CERAMIC,CHIP 0.1NF,5%,50V,C0G,TP,1608
C449 2203-001656 C-CERAMIC,CHIP 0.47nF,5%,50V,NP0,TP,1608

7 Electrical Parts List

7-4 LS15E33C/LS17E34C

Loc. No. Code No. Description Specification Remarks