Samsung LNV-6071R, LNV-6031R, LNV-6021R, LNO-6071R, LNO-6031R User Manual

...

NETWORK CAMERA

User Manual

LND-6011R/LND-6021R/LND-6031R/LND-6071R LNO-6011R/LNO-6021R/LNO-6031R/LNO-6071R LNV-6011R/LNV-6021R/LNV-6031R/LNV-6071R

Network Camera

User Manual

Hanwha Techwin

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.

Disclaimer

Hanwha Techwin

provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. right to change the contents of this document without prior notice.

Design and specications are subject to change without prior notice.

The initial administrator ID is “admin” and the password should be set when logging in for the rst time.

Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be

Co., Ltd. All r ights reser ved.

Hanwha Techwin

reserves the

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.

(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.)

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from PoE , 0.18A.

16. If you use excessive force when installing the product, the camera may be damaged and malfunction. If you forcibly install the product using non-compliant tools, the product may be damaged.

17. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or near the kitchen table. This may cause damage to the product.

18. When installing the product, be careful not to allow the surface of the product to be stained with chemical substance. Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface.

19. If you install/disassemble the product in a manner that has not been recommended, the production functions/ performance may not be guaranteed. Install the product by referring to “Installation & connection” in the user manual.

20. Installing or using the product in water can cause serious damage to the product.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

●● OVERVIEW

English _3

overview

Class construction

An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

ATTENTION

IL Y A RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE TYPE INCORRECT. METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Please use the input power with just one camera and other devices must not be connected.

The ITE is to be connected only to PoE networks without routing to the outside plant.

The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3af shall be a UL Listed device with the output evaluated as a Limited Power Source as defined in UL60950-1.

Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102. As such, associated Ethernet wiring shall be limited to inside the building.

Please read the following recommended safety precautions carefully.

yDo not place this apparatus on an uneven surface. yDo not install on a surface where it is exposed to direct sunlight, near heating equipment or

heavy cold area. yDo not place this apparatus near conductive material. yDo not attempt to service this apparatus yourself. yDo not place a glass of water on the product. yDo not install near any magnetic sources. yDo not block any ventilation openings. yDo not place heavy items on the product. yPlease wear protective gloves when installing/removing the camera.

The high temperature of the product surface may cause a burn.

User’s Manual is a guidance book for how to use the products. The meaning of the symbols are shown below.

yReference : In case of providing information for helping of product’s usages yNotice : If there’s any possibility to occur any damages for the goods and human caused by

not following the instruction

 Please read this manual for the safety before using of goods and keep it in the safe place.

WARNING

To prevent damage which may caused by IR LED, don’t stare at operating lamp.

For below models only.

LND-6011R/LND-6021R/LND-6031R/LND-6071R

LNO-6011R/LNO-6021R/LNO-6031R/LNO-6071R

LNV-6011R/LNV-6021R/LNV-6031R/LNV-6071R

Risk Group 1

4_ overview

WARNING IR emitted from this product.

Do not stare at operating lamp.

Product tested against IEC 62471

CONTENTS

overview

installation & connection

3 Important Safety Instructions 6 Product Features 6 Recommended PC Specifications 6 Recommended Micro SD/SDHC Memory

Card Specifications

7 What’s Included (LND-

6011R/6021R/6031R/6071R)

7 What’s Included (LNO-

6011R/6021R/6031R/6071R)

8 What’s Included (LNV-

6011R/6021R/6031R/6071R)

9 At a Glance (LND-6011R/6021R/6031R) 10 At a Glance (LND-6071R) 12 At a Glance (LNO-6011R/6021R/6031R) 12 At a Glance (LNO-6071R) 13 At a Glance (LNV-6011R/6021R/6031R) 14 At a Glance (LNV-6071R)

15 Installation (LND-

6011R/6021R/6031R/6071R)

16 Installation (LNO-

6011R/6021R/6031R/6071R)

18 Installation (LNV-

6011R/6021R/6031R/6071R)

20 Inserting/Removing a Micro SD Memory

Card

22 Powering and networking

network connection and

setup

web viewer

appendix

23 Connecting the Camera Directly to Local

Area Networking

23 Connecting the Camera Directly to a DHCP

Based DSL/Cable Modem

24 Connecting the Camera Directly to a

PPPoE Modem

24 Connecting the Camera to a Broadband

Router with the PPPoE/Cable Modem

25 Buttons used in IP Installer 25 Static IP Setup 27 Dynamic IP Setup 27 Port Range Forward (Port Mapping) Setup 28 Connecting to the Camera from a Shared

Local PC

28 Connecting to the Camera from a Remote

PC via the Internet

29 Connecting to the Camera 30 Password setting 30 Login 30 Plug-in support specifications for each

browser

31 Installing WebViewer Plugin 31 Using a Plug-in Free Webviewer

32 Specification 36 Product Overview 39 Troubleshooting 40 Open Source Announcement

●● OVERVIEW

English _5

overview

PRODUCT FEATURES

• Dustproof/Waterproof (IP66) (LNO-6011R/6021R/6031R/6071R, LNV-6011R/6021R/6031R/6071R) The dustproof and waterproof design makes you feel at ease when installing the product outdoors or exposing

it to rain.

• IR mode If the IR indicator turns on, the product switches to the IR mode for preventing an object from being too bright,

which helps you identify the object in near distance.

• Supports 2 megapixel resolution videos

• Multi-Streaming This network camera can display videos in different resolutions and qualities simultaneously using different

CODECs.

• Web Browser-based Monitoring Using the Internet web browser to display the image in a local network environment.

• Alarm When an event occurs, related videos are sent to the user’s registered e-mail and FTP server or stored on the Micro

SD memory card.

• Tampering Detection Detects tempering attempts on video monitoring.

• Motion Detection Detects motion from the camera’s video input.

• ONVIF Compliance This product supports ONVIF Profile S&G. For more information, refer to www.onvif.org.

RECOMMENDED PC SPECIFICATIONS

• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher

• Supported OS : Windows, Mac OS X

• Plug-in free web viewer Supported web browsers : Google Chrome, MS Edge, Mozilla Firefox(Window 64bit only), Apple Safari(Mac OS X only)

• Plug-in Webviewer Supported web browsers : MS Explorer

• VGA : PCIe 256MB GDDR3 video graphics card or higher

※

For detailed version information on the OS and the browser, please refer to the appendix.

RECOMMENDED MICRO SD/SDHC MEMORY CARD SPECIFICATIONS

• Recommended capacity : 16GB ~ 32GB (MLC Type)

• For your camera, we recommend you use a memory card from the following manufacturers: Micro SD/SDHC Memory Card : Sandisk, Transcend

6_ overview

WHAT’S INCLUDED (LND-6011R/6021R/6031R/6071R)

Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.)

Appearance Item Name Quantity Description

WHAT’S INCLUDED (LNO-6011R/6021R/6031R/6071R)

Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.)

Appearance Item Name Quantity Description Model Name

●● OVERVIEW

Camera

Warranty card

(Optional)

Template

Product installation guide

Camera

Warranty card

(Optional)

Template

RJ45 waterproof accessory

Card-type moisture absorbent

Product installation guide

Used to install in humid places

Attached when installed. LNO-6071R

LNO-6011R/6021R/

6031R/6071R

Use for all models

English _7

overview

WHAT’S INCLUDED (LNV-6011R/6021R/6031R/6071R)

Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.)

Appearance Item Name Quantity Description Model Name

Camera

Warranty card

(Optional)

Template

Star-shaped wrench

Card-type moisture absorbent

Cable bush

Product installation guide

Used for the assembly and disassembly

of dome covers

Attached when installed.

Used to connect the LAN cable with a

diameter of Ø7~8.5.

LNV-6011R/6021R/

6031R/6071R

Use for all models

8_ overview

AT A GLANCE (LND-6011R/6021R/6031R)

Appearance

Components

a b

Item Description

Dome cover

Camera Case

Case cover used to protect the lens and the main unit.

Housing part that covers the camera body.

cdb

ACT LINK NETWORK

FRONT

Item Description

Inside cover Protective cover for the main body.

Illumination Sensor Detects incoming light to control the IR LED.

Lens Lens for the camera.

IR LED These infrared LED’s are controlled by the illumination sensor.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that DHCP can be

Reset Button

Micro SD Memory Card

Compartment

enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

Compartment for the Micro SD memory card.

RESET

f g

●● OVERVIEW

NETWORK

ACT LINK

PoE connector Supply power through the Ethernet cable and connect to the network.

English _9

overview

AT A GLANCE (LND-6071R)

Appearance

Item Description

a b

Dome cover

Camera Case

Case cover used to protect the lens and the main unit.

Housing part that covers the camera body.

Components

i h

NETWORK

ACT

LiNK

FRONT

10_ overview

LINK

RESET

NETWORK

ACT

Item Description

Inside cover Protective cover for the main body.

Illumination Sensor Detects incoming light to control the IR LED.

Lens Lens for the camera.

IR LED These infrared LED’s are controlled by the illumination sensor.

PoE connector Supply power through the Ethernet cable and connect to the network.

Micro SD Memory Card

Compartment

Reset Button

Zoom control lever

Focus control lever

Compartment for the Micro SD memory card.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that DHCP can be

T Zoom in (Tele)

W Zoom out (Wide)

Release the lever and move it to left or right to zoom the lens in or out. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

N Focusing on a near object (Near)

F Focusing on a far object (Far)

Release the lever and move it to left or right to adjust the lens focus. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

●● OVERVIEW

English _11

overview

AT A GLANCE (LNO-6011R/6021R/6031R)

Appearance

Item Description

Micro SD card slot

Reset button

(Internal space of the product) This is a slot in which you can insert a Micro SD card.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that DHCP can be

AT A GLANCE (LNO-6071R)

Appearance

Item Description

Micro SD card slot

Reset button

(Internal space of the product) This is a slot in which you can insert a Micro SD card.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

d e

If you reset the camera, the network settings will be adjusted so that DHCP can be enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

PoE connector Supply power through the Ethernet cable and connect to the network.

12_ overview

PoE connector

Focus control lever

Zoom control lever

Supply power through the Ethernet cable and connect to the network.

N Focusing on a near object (Near)

F Focusing on a far object (Far)

Release the lever and move it to left or right to adjust the lens focus. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

T Zoom in (Tele)

W Zoom out (Wide)

Release the lever and move it to left or right to zoom the lens in or out. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

AT A GLANCE (LNV-6011R/6021R/6031R)

Components

Appearance

Dome cover

Camera Case

Item Description

Case cover used to protect the lens and the main unit.

Housing part that covers the camera body.

b ca

DC12V

Item Description

Illumination Sensor Detects incoming light to control the IR LED.

Lens Lens for the camera.

IR LED These infrared LED’s are controlled by the illumination sensor.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that DHCP can be

Reset button

Micro SD Memory Card

Compartment

Compartment for the Micro SD memory card.

RESET

e f

NETWORK

ACT LINK

●● OVERVIEW

PoE connector Supply power through the Ethernet cable and connect to the network.

English _13

overview

AT A GLANCE (LNV-6071R)

Appearance

Item Description

a b

Dome cover

Camera Case

Case cover used to protect the lens and the main unit.

Housing part that covers the camera body.

Components

b ca

d e

NETWORK

LiNK

ACT

Item Description

Illumination Sensor Detects incoming light to control the IR LED.

Lens Lens for the camera.

IR LED These infrared LED’s are controlled by the illumination sensor.

Focus control lever

Zoom control lever

Reset button

Micro SD Memory Card

Compartment

RESET

N Focusing on a near object (Near)

F Focusing on a far object (Far)

Release the lever and move it to left or right to adjust the lens focus. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

T Zoom in (Tele)

W Zoom out (Wide)

Release the lever and move it to left or right to zoom the lens in or out. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that DHCP can be

Compartment for the Micro SD memory card.

RESET

14_ overview

PoE connector

Supply power through the Ethernet cable and connect to the network.

installation & connection

INSTALLATION (LND-6011R/6021R/6031R/6071R)

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

• For the manual variable focal lens camera, features such as focus and zoom should be adjusted before installation. When adjusting these, be sure to prevent foreign substances from becoming attached.

Disassembling

1. Use one hand to hold the camera’s bottom part and turn the cover

counterclockwise with another hand to separate it.

2. Lift up the inner cover to separate it.

LiNK

NETWORK

ACT

LiNK

NETWORK

ACT

Dome Cover

Installation

1. Attach the installation template to the desired location, and drill

holes by following the template.

●● INSTALLATION & CONNECTION

2. Use the tapping screws to secure the camera to the holes drilled

through the template.

Set the < > mark imprinted on the camera to face the direction of camera

monitoring.

3. Connect the camera internal terminal with the corresponding cable.

4. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. (page 20)

You are recommended not to touch the lens separately, as it is shipped

from the factory with the focus correctly adjusted when the inspection is completed. Touching the lens may cause the focus to become distorted or the lens to become dirty. (LND-6011R/6021R/6031R)

For the manual variable focal lens camera, features such as focus and zoom should be adjusted before installation.

When adjusting these, be sure to prevent foreign substances from becoming attached. (LND-6071R)

5. Please connect the inner cover to the main body.

FRONT

6. While grabbing the bottom side of the camera with your hand, please grab and push its cover with the other hand to align the two arrow signs, as shown in the figure.

To assemble the dome cover, make the arrows match each other and press the

cover firmly. If the dome cover is rotated during assembly or is assembled incorrectly, diffused reflection may occur or the lens section may rotate, which will cause the shooting range to be changed.

Make sure that the dome cover is correctly connected to the bottom part as shown

in the figure. If the snap-fit is not connected correctly, the dome cover may fall, which may cause injury.

FRONT

LiNK

ACT

NETWORK

FRONT

LiNK

ACT

NETWORK

English _15

installation & connection

INSTALLATION (LNO-6011R/6021R/6031R/6071R)

This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are

recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

Installation

1. Attach the installation template to the desired location, and drill

holes by following the template.

2. Use the tapping screws to secure the camera to the holes drilled through the template.

3. Connect the appropriate cables with camera terminals.

Mounting Template

Cable Line

How to connect the RJ45 waterproof cable to a LAN cable

1. Insert it through the arrow direction.

2. Connect the LAN connector (male) to the cable.

3. Connect the RJ45 modular jack (female) to the RJ45 connector

(male).

Please, keep each of the parts separated.

4. Assemble by rotating the RJ45 modular jack (female) and the RJ45 protection cover clockwise (Follow the arrow).

5. Assemble by rotating RJ45 protection cover and back cover clockwise (Follow the arrow). When the back cover is assembled, the cable waterproof gasket is tightly attached to the cable to make it waterproof.

RJ45 modular

jack (female)

RJ45 connector (male)

Rubber ring

RJ45 connector protection cover

Back cover

Rubber ring

Cable waterproof

gasket

4. Adjust the orientation of the camera using a Phillips screwdriver.

When you adjust the camera position using a bracket, please loosen the

bracket screw, adjust the camera, and tighten it. If you attempt to adjust it forcibly while the screw is tight, it may result in a scratch or other problems.

16_ installation & connection

You must fully assemble it to rotate the back cover up to the end of the screw

thread of the RJ45 connector.

+ 35 hidden pages