Samsung LNT3253HX/XAA, LNT2653HX/XAA, LNT2354HX/XAA User Manual

Contact SAMSUNG WORLD-WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.

Contacte con SAMSUNG WORLD-WIDE Si tiene alguna pregunta o comentario referente a nuestros productos, por favor contacte con nuestro Servicio de Atención al Cliente.

LN-T2353H

Country

CANADA 1-800-SAMSUNG (7267864) www.samsung.com/ca

U.S.A 1-800-SAMSUNG (7267864) www.samsung.com

Customer Care Center

Web Site Address

Samsung Electronics Canada Inc., Customer Service 55 Standish Court Mississauga, Ontario L5R 4B2 Canada

Samsung Electronique Canada Inc., Service à la Clientèle 55 Standish Court Mississauga, Ontario L5R 4B2 Canada

Samsung Electronics America, Inc. 105 Challenger Road Ridgefield Park, NJ 07660-0511

LN-T2354H LN-T2653H LN-T3253H LN-T4053H

TFT-LCD TELEVISION

BN68-01156B-01

Owner’s Instructions

Record your Model and Serial number here for future reference.

· Model __________ · Serial No. ____________

Precautions When Displaying a Still Image

A still image may cause permanent damage to the TV screen

• Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention. This image retention is also known as "screen burn". To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

• Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and center of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause a similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.

• Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

Precauciones al mostrar en la pantalla una imagen fija

La imagen fija puede causar daños permanentes en la pantalla del televisor.

• No deje una imagen fija en la pantalla LCD durante más de dos horas ya que se podría producir una retención de la imagen en la pantalla. Este fenómeno de retención de imágenes también se denomina “quemadura de pantalla”. Para evitar que se produzca esa persistencia de la imagen, reduzca el nivel de luminosidad y de contraste de la pantalla cuando muestre imágenes fijas.

• El uso del televisor LCD en formato 4:3 durante un tiempo prolongado puede dejar rastros de bordes en las

partes izquierda, derecha y central de la pantalla debido a las diferencias en la emisión lumínica de la pantalla. La reproducción de un DVD o el uso de una consola de videojuegos pueden provocar un efecto similar en la pantalla. Reproducir un DVD o una videoconsola puede causar un efecto similar en la pantalla. La garantía no cubre estos daños.

• Ver imágenes fijas de videojuegos y PC durante más tiempo del indicado puede producir restos de imágenes parciales.

Para evitar este efecto, reduzca el ‘brillo’ y el ‘contraste’ cuando vea imágenes fijas.

Contents

GENERAL INFORMATION

■

List of Features .........................................................................2

■

Accessories ..............................................................................2

■

Viewing the Control Panel .......................................................3

■

Viewing the Connection Panel (depending on the model) ........ 4

■

Remote Control (LN-T2353H, LN-T2354H , LN-T2653H) ........5

■

Remote Control (LN-T3253H, LN-T4053H) ..............................6

■

Installing Batteries in the Remote Control ................................7

CONNECTIONS

■

Connecting VHF and UHF Antennas ........................................7

■

Connecting Cable TV ................................................................ 8

■

Connecting a VCR ....................................................................9

■

Connecting a DVD Player/Set-Top Box ..................................10

■

Connecting a Camcorder .......................................................10

■

Connecting a DVD Player/Set-Top Box via HDMI .................. 11

■

Connecting a DVD Player/Set-Top Box via DVI ...................... 11

■

Connecting a Digital Audio System .........................................12

■

Connecting an Amplier/DVD Home Theater .........................12

■

Connecting a PC ..................................................................... 12

OPERATION

■

Turning the TV On and Off ......................................................13

■

Plug & Play Feature ................................................................13

■

Changing Channels ................................................................ 14

■

Adjusting the Volume ..............................................................15

■

Viewing the Display ................................................................15

■

Viewing the Menus .................................................................16

■

Memorizing the Channels .......................................................16

■

Setting Up Your Remote Control (depending on the model)... 18

■

Remote Control Codes ........................................................... 20

■

To Select the Source (depending on the model)..................... 23

■

To Edit the Input Source Name (depending on the model) .....23

PICTURE CONTROL

■

Using Automatic Picture Settings ............................................24

■

Adjusting the Color Tone ......................................................... 25

■

Activating Backlight ................................................................. 25

■

Adjusting the Detailed Settings ...............................................26

■

Changing the Screen Size ......................................................29

■

Setting the Active Color .......................................................... 30

■

DNIe (Digital Natural Image engine) .......................................30

■

Freezing the Picture (depending on the model)...................... 31

■

HDMI Black Level ................................................................... 31

■

Setting the Film Mode .............................................................31

■

Viewing Picture-in-Picture ....................................................... 32

SOUND CONTROL

■

Customizing the Sound ........................................................... 34

■

Using Automatic Sound Settings ............................................ 34

■

Setting the TruSurround XT ....................................................35

■

Choosing a Multi-Channel Sound (MTS) track - Digital .........35

■

Choosing a Multi-Channel Sound (MTS) track - Analog ........36

■

Automatic Volume Control ......................................................36

■

Selecting the Internal Mute .....................................................37

■

Setting the On/Off Melody ......................................................37

■

Listening to the Sound of the Sub (PIP) Picture ..................... 38

■

Resetting the Sound Settings to the Factory Defaults ............38

■

Connecting Headphones ........................................................ 38

■

Selecting the Antenna ............................................................. 39

CHANNEL CONTROL

■

Clearing Scrambled Channels - Digital ...................................39

■

Setting the Channel Lists ........................................................40

■

To set-up Your Favorite Channels ...........................................41

■

Using the Channel Lists ..........................................................42

■

Viewing the Channel Lists ......................................................42

■

Labeling Channels ..................................................................43

■

LNA (Low Noise Amplier) ...................................................... 43

■

Fine Tuning Analog Channels .................................................44

■

Checking the Digital-Signal Strength ......................................44

PC DISPLAY

■

Using Your TV as a Computer (PC) Display ........................... 45

■

Display Modes ........................................................................ 45

■

Setting up the TV with your PC ............................................... 46

■

Setting the Home Theater PC ................................................. 47

TIME SETTING

■

Setting the Clock ..................................................................... 48

FUNCTION DESCRIPTION

■

Selecting a Menu Language ...................................................52

■

Setting the Blue Screen Mode ................................................52

■

Using the Game Mode ............................................................53

■

Viewing Closed Captions (On-Screen Text Messages) -

Analog .....................................................................................

■

Viewing Closed Captions (On-Screen Text Messages) -

Digital ......................................................................................

■

Menu Transparency Level ...................................................... 56

■

Using the Energy Saving Feature ...........................................56

■

Setting the Function Help .......................................................57

■

Setting the Light Effect ............................................................ 57

■

Digital Noise Reduction ..........................................................58

■

Using the V-Chip ..................................................................... 59

■

Upgrading the Software (depending on the model) ................66

WISELINK

■

Using the WISELINK Function (LN-T3253H, LN-T4053H) .....67

■

Using the WISELINK Menu ....................................................68

■

Using the PHOTO (JPEG) List ...............................................69

■

Using the MP3 List .................................................................. 76

■

Using the Setup Menu ............................................................ 78

ABOUT ANYNET

■

What is Anynet+? (LN-T3253H, LN-T4053H) ........................80

■

Connecting Anynet+ Devices .................................................. 80

■

Setting Up Anynet+ ................................................................. 81

■

Scanning and Switching between Anynet+ Devices ............... 81

■

Recording ...............................................................................82

■

Listening through a Receiver (Home theater) .........................83

■

Check Points before Requesting Service ............................... 83

APPENDIX

■

Troubleshooting ......................................................................84

■

Installing the Stand ................................................................. 86

■

Disconnecting the Stand .........................................................86

■

Wall- Mount Adjustment (LN-T4053H) (Sold separately) ........87

■

Wall Mount Kit Specications ( VESA ) ...................................88

■

Using the Anti-Theft Kensington Lock .....................................89

■

Specications .......................................................................... 89

English

English - 1

Symbol Press Important Note One-Touch

Button

General Information

List of Features

 Adjustable picture settings that can be stored in the TV’s memory.  Automatic timer to turn the TV on and off.  A special sleep timer.  V-Chip function.  Excellent Digital Interface & Networking :

With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Set-Top Box needed.  Remote Control The supplied remote can be used to operate the TV as well as most DVD players, Set-top boxes, Cable Boxes and VCRs.  Excellent Picture Quality

- DNIe technology provides life-like clear images.

 SRS TruSurround XT

- SRS TruSurround XT provides a virtual Dolby surround system.

Accessories

Please make sure the following items are included with your LCD TV. If any items are missing, contact your dealer.

Remote Control & Batteries (AAA x 2) LN-T2353H, LN-T2653H (BN59-00598A) LN-T2354H (BN59-00615A) LN-T3253H, LN-T4053H (BN59-00599A)

Stand LN-T2353H (BN96-04663A) LN-T2354H (BN96-04663B) LN-T2653H (BN96-04663A)

LN-T3253H (BN96-04662A)

The items color and shape may vary depending on the model.

Stand Screw LN-T2353H, LN-T2653H, LN-T3253H (6002-001294) LN-T2354H (6003-001324)

Power Cord

(3903-000144)

Cleaning Cloth

(BN63-01798A)

Owner’s Instructions

Cover-Bottom LN-T2353H, LN-T2653H (BN63-03221B) LN-T2354H (BN63-03221C) LN-T3253H (BN63-03103B) LN-T4053H (BN63-03113B)

Warranty Card / Registration

Card / Safety Guide Manual

(Not available in all locations)

English - 2

Viewing the Control Panel

Buttons on the Lower-Right Part of the Panel

The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control.

1 2

The product color and shape may vary depending on the model.

SOURCE

Toggles between all the available input sources (TV, AV1, AV2, S-Video 1, S-Video 2, Component1, Component2, PC, HDMI1, HDMI2, HDMI3). In the on-screen menu, use this button as you would use the ENTER button on the remote control.

23,26 inch model supports TV, AV1, AV2, S-Video1, S-Video 2, Component 1,Component 2, PC, HDMI1, and HDMI2 only.

Press to see an on-screen menu of your TV’s features.

+ VOL -

Press to increase or decrease the volume. In the on-screen menu, use the + VOL - buttons as you

would use the ◄ and ► buttons on the remote control.

Front Panel buttons

Touch the right side of each button to operate.

4 CH

Press to change channels.

In the on-screen menu, use the you would use the ▲ and ▼ butons on the remote control.

(POWER)

Press to turn the TV on and off. POWER INDICATOR Blinks and turns off when the power is on and lights up

in stand-by mode.

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

SPEAKERS

buttons as

English - 3

Viewing the Connection Panel (depending on the model)

Rear Panel Jacks

Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players. For more information on connecting equipment, see pages 6-12.

[Side Panel Jacks]

AUDIO OUT

Connects to the audio input jacks on your Amplifier/ Home theater.

2 DIGITAL AUDIO OUT (OPTICAL) Connects to a Digital Audio component.

3 PC IN Connects to the video and audio output jacks on your PC.

4 HDMI IN 1,2,3 /DVI IN(HDMI1) (AUDIO R/L)

Connects to the HDMI jack of a device with an HDMI output.

Use the HDMI IN 1 terminal for a DVI connection to an

external device. You should use the DVI to HDMI cable or DVI-HDMI adapter (DVI to HDMI) for a video connection, and the DVI IN ‘R-AUDIO-L’ terminal for audio.

- No sound connection is needed for an HDMI to HDMI

connection

- When using an HDMI/DVI cable connection, you must

use the HDMI IN 1 terminal.

- 23,26 inch model supports HDMI1 and HDMI2 only.

5 ANT 1 IN/ANT 2 IN Connects to an antenna or cable TV system.

EX LINK

Connect this to the jack on the optional wall mount

bracket. This will allow you to adjust the TV viewing angle using your remote control.

COMPONENT IN

Connects Component video/audio.

SERVICE (LN-T2353H, LN-T2354H, LN-T2653H)

Connector for SERVICE only

AV IN 1 / AV IN 2

Video and audio inputs for external devices, such as a camcorder or VCR. S-VIDEO Connects an S-Video signal from a camcorder or VCR.

POWER INPUT

Connects the supplied power cord

KENSINGTON LOCK

The Kensington lock (optional) is a device used to physically fix the system when used in a public place. If you want to use a locking device, contact the dealer where you purchased the TV. The place of the Kensington Lock may be different depending on its model.

HEADPHONE

Connects a set of external headphones for private listening.

WISELINK (LN-T3253H,LN-T4053H)

Connect a USB mass storage device to view photo files(JPEG) and play audio files (MP3).

English - 4

Remote Control (LN-T2353H, LN-T2354H, LN-T2653H)

You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always point it directly at the TV. You can also use your remote control to operate your VCR, Cable box, DVD player, or Set-Top Box.

POWER

Turns the TV on and off.

NUMERIC BUTTONS

Press to change the channel.

–

Press to select additional channels(digital and analog) being broadcast by the same station. For example, to select channel “54-3”, press “54”, then press “–” and “3”.

CH LIST

Used to display Channel Lists on the screen.

ANTENNA

Press to select “AIR” or “CABLE”.

VCR/DVD Functions

- Rewind

- Stop

- Play/Pause

- Fast/Forward

VOL / VOL

Press to increase or decrease the volume.

8 (

MUTE)

Press to temporarily cut off the sound.

Displays the main on-screen menu.

S.MODE

Press to select the sound mode.

RETURN

Returns to the previous menu.

P.MODE

Press to select the picture mode.

SRS

Selects SRS TruSurround XT mode.

MTS Press to choose stereo, mono or

Separate Audio Program (SAP broadcast).

SLEEP

Press to select a preset time interval for automatic shut off.

AUTO PROG.

Press to automatically store selected TV/Cable channels.

SET

Sets the remote to control your TV, VCR, Cable, DVD, or Set-Top Box

TV, DVD, STB, CABLE, VCR Press to operate your TV, DVD, STB, CABLE (box), or VCR

see pages 18~22.)

(

When pressing this button, a number of buttons on the remote control (e.g. TV, DVD, STB, CABLE, VCR, VOL and CH buttons) light up for a few seconds and then turn off to save power. This function is convenient for using the remote at night or when dark. (LN-T2353H, LN-T2653H)

)

SOURCE

Press to display all of the available video sources.

PRE-CH Tunes to the previous channel.

FAV.CH

Press to switch to your favorite channels.

HDMI

Selects the HDMI mode directly.

/ CH

Press to change channels.

EXIT

Press to exit the menu.

UP▲ / DOWN▼ / LEFT◄ RIGHT►

Use to select on-screen menu items and change menu values.

Press to display information on the TV screen.

particular scene. Press again to resume normal video.

Picture-in Picture ON/OFF.

sequence. (These buttons change channels in the PIP window only.)

Use to store and delete channels to/from memory.

change the batteries and press the RESET button for 2-3 seconds before use.

/ ENTER

INFO

CAPTION

Controls the caption decoder.

STILL

Press to stop the action during a

P.SIZE

Picture size selection.

PIP

CH /

Displays the available channels in

ADD/DEL

RESET

When your remote does not work,

This is a special remote control for the visually impaired, and has Braille

points on the Power, Channel, STOP, PLAY/PAUSE and Volume buttons.

The performance of the remote control may be affected by bright light.

English - 5

Remote Control (LN-T3253H, LN-T4053H)

POWER

Turns the TV on and off.

NUMERIC BUTTONS

Press to change the channel.

–

Press to select additional channels(digital and analog) being broadcast by the same station. For example, to select channel “54-3”, press “54”, then press “–” and “3”.

CH LIST

Used to display Channel Lists on the screen.

ANTENNA

Press to select “AIR” or “CABLE”.

VCR/DVD Functions

- Rewind

- Stop

- Play/Pause

- Fast/Forward

VOL / VOL

Press to increase or decrease the volume.

8 (

MUTE)

Press to temporarily cut off the sound.

Displays the main on-screen menu.

S.MODE

Press to select the sound mode.

RETURN

Returns to the previous menu.

P.MODE

Press to select the picture mode.

CAPTION

Controls the caption decoder.

FAV.CH

Press to switch to your favorite channels.

SLEEP

Press to select a preset time interval for automatic shut off.

SRS

Selects SRS TruSurround XT mode.

SET

Sets the remote to control your TV, VCR, Cable, DVD, or Set-Top Box

TV, DVD, STB, CABLE, VCR Press to operate your TV,DVD, STB, CABLE (box), or VCR (See pages 18-22)

(

This is a special remote control for the visually impaired, and has Braille points on the Power, Channel, STOP, PLAY/PAUSE and Volume buttons.

The performance of the remote control may be affected by bright light.

)

SOURCE

Press to display all of the available video sources.

PRE-CH

Tunes to the previous channel.

WISELINK

This function enables you to view and play photo (JPEG) and audio files (MP3) from an external device. (Refer to page

REC

Records for Live Broadcasting.

Press to change channels.

EXIT

Press to exit the menu.

UP▲ / DOWN▼ / LEFT◄

RIGHT►

Use to select on-screen menu items and change menu values.

INFO

Press to display information on the TV screen.

Anynet+

Runs the Anynet view functions and

sets up Anynet devices.

STILL

Press to stop the action during a particular scene. Press again to resume normal video.

P.SIZE

Picture size selection.

PIP

Picture-in Picture ON/OFF.

CH /

Displays the available channels in sequence. (These buttons change channels in the PIP window only.)

MTS

Press to choose stereo, mono or Separate Audio Program (SAP broadcast).

RESET

When your remote does not work, change the batteries and press the RESET button for 2-3 seconds before use.

/ CH

68)

/ ENTER

English - 6

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the figure.

Install two AAA size batteries.

Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.

Replace the cover. Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV. (Assuming typical TV usage, the batteries should last for about one year.)

If the remote control doesn’t work, check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage, or is the power cord unplugged?

5. Is there a special fluorescent light or neon sign nearby?

Connections

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like the diagram to the right, see “Antennas with 300

Ω Flat Twin Leads” below.

If your antenna has one lead that looks like diagram to the right, see “Antennas with 75 Ω Round Leads”.

If you have two antennas, see “Separate VHF and UHF Antennas”.

Antennas with 300 Ω Flat Twin Leads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears") that has 300 Ω twin at leads, follow the directions

below.

1. Place the wires from the twin leads under the screws on a 300-75 Ω adapter

(not supplied). Use a screwdriver to tighten the screws.

Plug the adaptor into the ANT 2 IN (CABLE) terminal on the back of the TV.

ANT 2 IN (CALBE)

Antennas with 75 Ω Round Leads

Plug the antenna lead into the ANT 1 IN (AIR) terminal on the back of the TV.

ANT 1 IN

(AIR)

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

Connect both antenna leads to the combiner.

UHF

VHF

Plug the combiner into the ANT 1 IN (AIR) terminal on the bottom of the rear panel.

English - 7

ANT 1 IN

(AIR)

UHF

VHF

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

Plug the incoming cable into the ANT 2 IN (CABLE) terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.

Connecting to a Cable Box that Descrambles All Channels

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.

ANT IN

ANT 2 IN (CABLE)

ANT OUT

2. Connect the other end of this cable to the ANT 2 IN (CABLE) terminal on the back of the TV.

ANT 2 IN (CABLE)

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a twoway splitter, an RF (A/B) switch, and four lengths of RF cable. (These items are available at most electronics stores.)

1. Find and disconnect the cable that is connected to the ANT IN terminal on your cable box.

Connect this cable to a two-way splitter.

This terminal might be labeled “ANT IN”,

"VHF IN” or simply, “IN”.

3. Connect an RF cable between the OUTPUT terminal on the splitter and the IN terminal on the cable box.

Incoming

cable

4. Connect an RF cable between the

ANT OUT terminal on the cable box and the B–IN terminal on the RF(A/B) switch.

Incoming

cable

Splitter

5. Connect another cable between the other

OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch.

Incoming

cable

Splitter

6. Connect the last RF cable between the

OUT terminal on the RF (A/B) switch and the ANT IN terminal on the rear of the TV.

Incoming

cable

Splitter

After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)

Splitter

Cable Box

ANT IN

Incoming

cable

Cable Box

Splitter

RF (A/B)

Switch

Cable Box

RF (A/B)

Switch

RF (A/B)

Switch

ANT IN

TV Rear

English - 8

Connecting a VCR

Video Connection

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 7-8). Skip step 1 if you have not yet connected to an antenna or a cable system.

Unplug the cable or antenna

from the back of the TV.

Connect the cable or antenna to the ANT IN terminal on the back of the VCR.

3. Connect an RF Cable between the ANT OUT terminal on the VCR and the ANT 1 IN (AIR) or ANT 2 IN (CABLE) terminal on the TV.

4. Connect a Video Cable between the VIDEO OUT jack on the VCR and the AV IN 1 (or AV IN 2) [VIDEO] jack on the TV.

5. Connect Audio Cables between the AUDIO OUT jacks on the VCR and the AV IN 1 (or AV IN 2) [R- AUDIO-L] jacks on the TV.

If you have a “mono” (non-stereo) VCR, use a Y-connector (not supplied) to hook up to the right and left audio input jacks of the TV. If your VCR is stereo, you must connect two cables.

VCR Rear Panel

Audio Cable (Not supplied)

Video Cable (Not supplied)

RF Cable (Not supplied)

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

Each VCR has a different back panel configuration. When connecting a VCR, match the color of the connection terminal to the cable.

ANT 1 IN

(AIR)

ANT 2 IN (CABLE)

TV Rear Panel

S-Video Connection

Your Samsung TV can be connected to an S-Video signal from an VCR. (This connection delivers a better picture as compared to a standard VCR.)

1. To begin, follow steps 1–3 in the previous section to connect the antenna or cable to your VCR and your TV.

Connect an S-Video Cable

VCR Rear Panel

between the S-VIDEO OUT jack on the VCR and the AV IN1 [S-VIDEO] jack on the TV.

Connect Audio Cables

between the AUDIO OUT jacks on the VCR and the AV IN1 [R-AUDIO-L] jacks on the TV.

An S-Video cable may be included with a VCR. (If not, check your local electronics store.)

Audio Cable (Not supplied)

S-Video Cable (Not supplied)

RF Cable (Not supplied)

Each VCR has a different back panel configuration. When connecting a VCR, match the color of the connection terminal to the cable.

English - 9

TV Rear Panel

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow you to view the camcorder tapes without using a VCR

1. Connect a Video Cable between the AV IN2 [VIDEO] jack on the TV and the VIDEO OUT jack on the camcorder.

Connect Audio Cables between the AV IN2 [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the camcorder.

Camcorder

Each Camcorder has a different back panel configuration. When connecting a Camcorder, match the color of the connection terminal to the cable.

TV Side Panel

Video Cable (Not supplied)

Audio Cable (Not supplied)

Connecting a DVD Player/Set-Top Box

The rear panel jacks on your TV make it easy to connect a DVD player to your TV.

Connect a Component

Cable between the COMPONENT IN(1 or 2) [Y, PB, PR] jacks on the TV and the COMPONENT [Y, PB, PR] jacks on the DVD/Set-top Box.

Connect Audio Cables between the COMPONENT IN(1 or 2) [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the DVD/Set-top Box

DVD Player/Set-Top Box

Audio Cable (Not supplied)

Component Cable (Not supplied)

Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red) for enhanced video quality. Be sure to match the component video and audio connections. For example, if connecting the video cable to COMPONENT IN, connect the audio cable to COMPONENT IN also.

Each DVD Player/STB has a different back panel configuration.

When connecting a DVD player/STB, match the color of the connection terminal to the cable.

TV Rear Panel

English - 10

Connecting a DVD Player/Set-Top Box via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.

Connect an HDMI Cable

between the HDMI IN (1,2 or 3) connector on the TV and the HDMI connector on the DVD player/Set-Top Box

DVD Player Rear Panel

TV Rear Panel

TV Side Panel

HDMI Cable (Not supplied)

What is HDMI?

• HDMI(High-Definition Multimedia Interface), is a next-generation an interface that enables the transmission of digital audio and video signals using a single cable.

• The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed.

Each DVD player/STB has a different back panel configuration. 32,40 inch model supports HDMI 3 only

Connecting a DVD Player/Set-Top Box via DVI

This connection can only be made if there is a DVI Output connector on the external device.

Connect a DVI to HDMI Cable or DVI-HDMI Adapter between the HDMI IN 1 connector on the TV and the DVI connector on the DVD player/Set-Top Box.

Connect Audio Cables between the DVI IN (HDMI 1) [R-AUDIO-L] jack on the TV and the AUDIO OUT jacks on the DVD player/ Set-Top Box.

DVD Player / Set-Top Box

TV Rear Panel

Audio Cable (Not supplied)

DVI to HDMI Cable (Not supplied)

Each DVD player/STB has a different back panel configuration. When connecting a DVD player/STB, match the color of the connection terminal to the cable.

When using an HDMI/DVI cable connection, you must use the HDMI IN 1 terminal.

English - 11

Connecting a Digital Audio System

The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV.

1. Connect an Optical Cable between the “DIGITAL

Digital Audio System

AUDIO OUT (OPTICAL)” jacks on the TV and the Digital Audio Input jacks on the Digital Audio System.

When a Digital Audio System is connected to the “DIGITAL AUDIO OUT (OPTICAL)” terminal: Decrease the volume

Optical Cable (Not supplied)

of the TV, and adjust the volume level with the system’s volume control.

5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH. Each Digital Audio System has a different back panel configuration. .

Connecting an Amplier/DVD Home Theater

TV Rear Panel

1. Connect Audio Cables

between the AUDIO OUT [R-AUDIO-L] on the TV and AUDIO IN [R-AUDIO L] on the Amplifier/DVD Home Theater.

When an audio amplifier is connected to the “AUDIO OUT [L-AUDIO-R]” terminals: Decrease the volume of the TV, and adjust the volume level with the Amplifier’s volume control.

Connecting a PC

1. Connect a D-Sub

Cable between PC IN [PC] connector on the TV and the PC output connector on your computer.

Connect a PC Audio

Cable between PC IN [AUDIO] jack on the TV and the Audio Out jack of the sound card on your computer.

TV Rear Panel

Amplier/DVD Home Theater

Audio Cable (Not supplied)

Each Amplifier/DVD Home Theater has a different back panel configuration. When connecting an Amplifier/DVD Home Theater, match the color of the connection terminal to the cable.

TV Rear Panel

PC Audio Cable (Not supplied)

D-Sub Cable (Not supplied)

Each PC has a different back panel configuration. When connecting a PC, match the color of the connection terminal to the cable. When using an HDMI/DVI cable connection, you must use the HDMI IN 1 terminal.

English - 12

Operation

Turning the TV On and Off

Press the POWER button on the remote control. You can also use the button on the front of the panel.

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently:

1. Press the POWER button on the remote control. The message “Menu language, Shop Mode, Channels and Time will be set.” is displayed. Press the ENTER button, then “Select the language of the OSD” menu is automatically displayed.

Press the ▲ or ▼ buttons to select language, then press the ENTER button.

The message “Select Home Mode when installing this TV at home.” is displayed.

Press the ◄ or ► buttons to select “Shop” or “Home”, then press the

ENTER button. The message “Select the antennas to memorize.” is displayed.

We recommend setting the TV to Home mode for the best picture in your home environment. Shop mode is only intended for use in retail environments. If the unit is accidentally set to Shop mode and you want to return to Dynamic (Home) mode, press any Volume button and then hold down the MENU button for five seconds on the side panel of the TV.

Press the ▲ or ▼ buttons to memorize the channels of the selected connection. Press the ENTER button to select “Start”. If the antenna is connected to ANT 1(AIR), select “Air” and if it is connected to ANT 2 (CABLE), select “Cable”.

If both ANT 1 (AIR) and ANT 2 (CABLE) are connected, select the “Air + Cable”. In Cable mode, you can select the correct signal source among STD, HRC,

and IRC by pressing the ▲ or ▼ button, then press the ENTER button. Contact your local cable company to identify the type of cable system that exists in your particular area.

The TV will begin memorizing all of the available channels.

After all the available channels are stored, the Auto program menu reappears. Press the ENTER button when channel memorization is complete. The message “Select the clock mode.” is displayed.

To stop the search before it has finished, press the ENTER button with stop selected.

Menu language, Shop Mode,

Channels and Time will be set.

Select the language of the OSD.

Menu Language

Move Enter Skip

Select Home Mode when installing this TV at home.

Move Enter Skip

Select the antennas to memorize.

Air Cable Air+Cable

Move Enter Skip

Auto Program in progress.

Enter Skip

Auto Program is completed. 16 Channels were memorized. Air : 16,

Shop

Cable : 0.

Start

Plug & Play

English

Español

Français

Plug & Play

Home

Plug & Play

Start Start Start

Plug & Play

Air Channel 50

35%

Stop

Plug & Play

6. Press the ENTER button.

Press the ▲ or ▼ buttons to select “Manual” or “Auto”, then Press the ENTER button. The message “Set to daylight savings time.” is displayed.

English - 13

Enter

Clock Set

Select the clock mode.

Clock Mode :

Move Enter Skip

Plug & Play

Manual

Auto

Skip

7. Press the ▲ or ▼ buttons to select “On” or “Off”, then Press the ENTER button.

The message “Select the time zone in which you live.” is displayed.

Set to daylight savings time.

Plug & Play

Daylight Savings Time :

Off

8. Press the ▲ or ▼ buttons to highlight the time zone for your local area.

Press the ENTER button. If you have received a digital signal, the time will be set automatically. If not, see page 49 to set the clock.

The message “Enjoy your watching.” is displayed.

9. When you have finished, press the ENTER button.

If you want to reset this feature...

1. Press the MENU

button to display the menu.

Press the ▲ or ▼ buttons to select “Setup”, then press the ENTER button.

2. Press the ENTER

3. The message “Menu language, Shop Mode, Channels and Time will be set."

button again, to select “Plug & Play”.

is displayed.

Move Enter Skip

Select the time zone in which you live.

Newfoundland

Atlantic

Eastern

Central

Mountain

Pacific Alaska Hawaii

Move Enter Skip

Plug & Play

Enjoy your watching.

Plug & Play ► Language : English ► Time

Game Mode : Off ►

V-Chip ► Caption ► Menu Transparency : High ▼More

Move Enter Return

Menu language, Shop Mode,

Channels and Time will be set.

Setup

►

Start

►

Changing Channels

Using the Channel Buttons

1. Press the CH or

When you press the CH or sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels). You will not see channels that were either erased or not memorized. See page 17 to memorize channels.

Using the PRE-CH Button to select the Previous Channel

1. Press the PRE-CH button.

The TV will switch to the last channel viewed. To quickly switch between two channels that are far apart, tune to one

channel, then use the number button to select the second channel. Then use the PRE-CH button to quickly alternate between them.

button to change channels.

button, the TV changes channels in

English - 14

Adjusting the Volume

1. Press the

VOL or VOL buttons to decrease or increase the volume.

Using Mute At any time, you can cut off the sound using the MUTE button.

Press MUTE button and the sound cuts off. The word “ “ will appear in the lower-left corner of the screen.

To turn mute off, press the MUTE button again, or simply press the

VOL or VOL buttons.

Viewing the Display

The display identies the current channel and the status of certain audio-video settings.

1. Press the INFO button on the remote control. The TV will display the channel, the type of sound,

and the status of certain picture and sound settings.

Air 7

Mono Picture Mode : Dynamic Sound Mode : Custom MTS : Stereo

05 : 54 pm

Press the INFO button once more or wait approximately 10 seconds and the

display disappears automatically.

English - 15

Viewing the Menus

1. With the power on, press the MENU button.

The main menu appears on the screen. The menu’ s left side has five icons: Picture, Sound, Channel, Setup, Input.

Use the ▲ or ▼ buttons to select one of the five icons.

Source List : TV ► Edit Name WISELINK Anynet+ (HDMI-CEC)

Input

►

Then press the ENTER button to access the icon’s sub-menu.

Press the EXIT button to exit.

Move Enter Exit

The on-screen menus disappear from the screen after about one minute.

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (Air) and “Cable” channels. After the available channels are memorized, use the CH or channels by entering the channels digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding or deleting channels (Channel Lists).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an Air or a Cable system).

Press the MENU button to display the menu.

Press the ▲ or ▼ buttons to select “Channel”, then press the ENTER button.

Press the ENTER button select “Antenna”.

Press the ▲ or ▼ buttons to select “Air” or “Cable”, then press the ENTER button. Press the EXIT

button to exit.

buttons to scan through the channels. This eliminates the need to change

Antenna : Air ► Auto Program ►

Clear Scrambled Channel ►

Channel List ► Name ► Fine Tune ►

Signal Strength ►

LNA : On ►

Move Enter Return

Antenna : Air

Auto Program

Clear Scrambled Channel

Channel List Name Fine Tune

Signal Strength

LNA : On

Move Enter Return

Channel

Air

Cable

English - 16

Storing Channels in Memory (Automatic Method)

Press the MENU button to display the menu. Press the ▲ or ▼ buttons to select “Channel”, then press the ENTER button.

Press the ▲ or ▼ buttons to select “Auto Program”, then press the ENTER button.

Press the ▲ or ▼ buttons to select the antenna connection, then press the ENTER button.

Air: “Air” antenna signal. / Cable: “Cable” antenna signal. / Air+Cable: “Air” and “Cable” antenna signals.

When selecting the Cable TV system: Press the ENTER button to start the auto

program. By default, the cable TV system is set to “STD”. If you want to select

another type of cable system, press the ▲ or ▼ button to select “STD”, “HRC” or

“IRC”. STD, HRC and IRC identify various types of cable TV systems. Contact your

local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected.

Press the ENTER

button to start the auto program.

To stop the search before it has finished, press the ENTER button with stop selected.

After all the available channels are stored, the “Auto Program” menu reappears. Press the EXIT button to exit.

Antenna : Air ► Auto Program

Clear Scrambled Channel

Channel List ► Name Fine Tune

Signal Strength

LNA : On

Select the antennas to memorize.

Air Cable Air+Cable

Select the cable system.

Move Enter Return

Auto Program in Progress.

Enter Return

Auto Program is completed. 16 Channels were memorized.

Cable : 0.

Air : 16,

Channel

►

Move Enter Return

Channel

Start

Move Enter Return

Auto Program

Analog

STD

HRC

IRC

Digital

STD

HRC

IRC

Move Enter Return

Auto Program

Plug & Play

Start

Cable Channel 50

Stop

►

35%

English - 17

Enter Return

Setting Up Your Remote Control (depending on the model)

After the television has been set up properly, your remote control can operate in five different modes: TV, DVD, Cable, Set-Top Box, VCR. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose.

The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top Boxes.

Setting Up the Remote to Operate Your VCR

1. Turn off your VCR.

2. Press the VCR

3. Press the SET

4. Using the number buttons on your remote control, enter three digits of the VCR code

listed on page 20 of this manual for your brand of VCR. Make sure you enter three digits

of the code, even if the first digit is a “0”.

(If more than one code is listed, try the first one.)

5. Press the POWER button on the remote control.

Your VCR should turn on if your remote is set up correctly.

If your VCR does not turn on after set up, repeat steps 2, 3, and 4, but try one of the

other codes listed for your brand of VCR.

If no other codes are listed, try each VCR code, 000 through 080.

Note on Using Remote Control Modes: VCR When your remote control is in “VCR” mode, the volume buttons still control your TV’s volume.

button on your TV’s remote control.

Setting Up the Remote to Operate Your Cable Box

1. Turn off your cable box.

2. Press the CABLE

3. Press the SET

4. Using the number buttons on your remote control, enter three digits of the cable box code

listed on page 21 of this manual for your brand of cable box. Make sure you enter three

digits of the code, even if the first digit is a “0”. (If there is more than one code listed, try

the first one.)

5. Press the POWER button on the remote control.

Your cable box should turn on if your remote is set up correctly.

If your cable box does not turn on after set up, repeat steps 2, 3, and 4, but try one of the

other codes listed for your brand of cable box. If no other codes are listed, try each code,

000 through 046.

Note on Using Remote Control Modes: Cable Box When your remote control is in “CABLE” mode, the volume buttons still control your TV’s volume.

button on your TV’s remote control.

English - 18

Setting Up the Remote to Operate Your DVD

1. Turn off your DVD.

2. Press the DVD

3. Press the SET

button on your TV’s remote control.

4. Using the number buttons on your remote control, enter three digits of the DVD code

listed on page 21~22 of this manual for your brand of DVD.

Make sure you enter three digits of the code, even if the first digit is a “0”.

(If there is more than one code listed, try the first one.)

5. Press the POWER button on the remote control.

Your DVD should turn on if your remote is set up correctly.

If your DVD does not turn on after set up, repeat steps 2, 3, and 4, but try one of the

other codes listed for your brand of DVD.

If no other codes are list-ed, try each code, 000 through 141.

Note on Using Remote Control Modes: DVD When your remote control is in “DVD” mode, the volume buttons still control your TV’s volume.

Setting Up the Remote to Operate Your STB

1. Turn off your STB.

2. Press the STB

3. Press the SET

button on your TV’s remote control. button on your TV’s remote control.

4. Using the number buttons on your remote control, enter three digits of the STB code

listed on page 22 of this manual for your brand of STB.

Make sure you enter three digits of the code, even if the first digit is a “0”.

(If there is more than one code listed, try the first one.)

5. Press the POWER button on the remote control.

Your STB should turn on if your remote is set up correctly.

If your STB does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other

codes listed for your brand of STB.

(If no other codes are listed, try each code, 000 through 074.)

Note on Using Remote Control Modes: STB When your remote control is in “STB” mode, the volume buttons still control your TV’s volume.

English - 19

Remote Control Codes

VCR

Brand Code

SAMSUNG 000 001 002 003 004 005 077 078 079 ADMIRAL 020 AIWA 025 AKAI 004 027 032 AUDIO DYNAMICS 007 026 BELL&HOWELL 018 BROKSONIC 022 CANDLE 002 003 006 008 015 055 CANON 021 056 CITIZEN 002 003 006 008 015 055 COLORTYME 007 CRAIG 002 024 CURTIS MATHES 002 007 008 017 021 025 056 064 066 DAEWOO 003 010 011 012 013 014 015 016 DB 007 026 DIMENSIA 017 DYNATECH 025 ELECTROHOME 034 EMERSON

FISHER 018 024 028 029 048 051 061 FUNAI 025 GENERAL ELECTRIC GO VIDEO 002 HARMAN KARDON 007 HITACHI 019 025 041 042 074 INSTANT REPLAY 021 JC PENNEY JCL JVC KENWOOD KLH KONIA LG(Goldstar) LIOYD LOGIK LXI MAGNAVOX MARANTZ MARTA MEI MEMOREX MGA MIDLAND MINOLTA MITSUBISHI

001 003 006 021 022 025 030 032 034 040 047 050 052 060 063 065 066 067 069 073

002 005 017 021 056

002 007 018 019 021 026 037 041 054 056 007 008 018 021 026 037 081 082 083 007 008 018 021 026 037 070 036 006 007 008 009 010 025 038 025 021 056 059 007 008 018 021 026 037 062 006 021 006 021 024 025 034 005 019 041 075 019 034 041 046

Brand Code

MONTGOMERY WARD MTC 002 025 MULTITECH 002 005 025 038 NEC 007 008 018 026 037 062 064 OPTIMUS 020 ORION 073 074 075 076 PANASONIC 021 056 071 072 PENTAX 019 041 075 PENTEX RESEARCH+ PHILCO 021 056 059 PHILIPS 021 080 PIONEER 019 026 039 053 PORTLAND 015 049 055 PROSCAN 017 QUARTZ 018 QUASAR 021 056 RADIO SHACK/

REALISTIC RCA SANSUI 026 SANYO 018 024 SCOTT 003 047 052 067 SEARS 006 018 019 024 028 029 041 048 051 SHARP 020 034 045 015 SHIMTOM 027 033 038 058 SIGNATURE 025 SONY 027 033 044 SYLVANIA 021 025 056 059 SYMPHONIC 025 TANDY 018 025 TASHIKA 006 TATUNG 037 TEAC 025 037 068 TECHNICS 021 TEKNIKA 006 021 025 031 TMK 066 TOSHIBA 003 019 029 051 052 TOTEVISION 002 006 UNITECH 002 VECTOR RESEARCH VICTOR 026 VIDEO CONCEPTS 007 026 VIDEOSONIC 002 WARDS YAMAHA 007 008 018 026 037 ZENITH 023 027 033

020

008

006 018 020 021 024 025 029 034 048 056

002 017 019 021 035 041 043 057 068 076

007 026

002 003 006 019 020 021 024 025 034 038 041

English - 20

CABLE BOX

Brand Code

SAMSUNG 000 001 002 003 004 005 006 007 GI 041 HAMLIN 003 024 031 HITACHI 025 030 JERROLD 038 039 MACOM 025 030 MAGNAVOX 019 023 028 OAK 026 PANASONIC 003 022 027 037 044 PHILIPS 019 021 023 028 PIONEER 004 018 020 044 RCA 014 022 040 REGAL 003

SAMSUNG DVD

Product Code

DVD 000 001 002 DVDR 003 004 BD Record 005 006 VCR COMBO 007 008 009 010 011 VCR Record 012 DHR COMBO 013

DVD

Brand Code

ANAM 030 AUDIOVOX 075 AUDIOLOGIC 085 ANABA 072 APEX DIGITAL 070 071 074 086 083 084 088 111 112 AIWA 114 BROKSONIC 062 BLAUPUNKT 074 B&K 122 123 CURTIS MATHES 027 CYBER HOME 077 078 079 082 CLARION 080 125 CIRRUS 081 CYBER HOME 065 CINEVISION 095 DAEWOO 066 DENON 146 FARENHEIT 067 068 FISHER 090 GPX 060 GO VIDEO 061 089 133 135 GE 069 074 GREENHILL 074 HITACHI 064 113 HITEKER 071 HOYO 073 HARMAN / KARDON IRT 089

091 110

Brand Code

REGENCY 015 023 SA 042 043 SCIENTIFIC ATLAN 042 043 SPRUCER 022 STARGATE 2000 036 SYLVANIA 016 TEXSCAN 016 TOCOM 032 UNIVERSAL 033 034 VIEWSTAR 019 021 023 028 WARNER AMEX 046 ZENITH 017 029 035 037 045

Product Code

Home Theater VCR COMBO 014 015 016 HDD Recorder COMBO 017 TWIN TRAY COMBO 018 STB DVD COMBO 019 DVD Receiver 020 AV Receiver 021

Brand Code

INTEGRA 092 JBL 091 JVC 022 033 115 116 JATON 073 KENWOOD 051 108 109 KISS 073 KONKA 059 100 106 107 KLH 074 075 LG(Goldstar) 025 031 LOEWE 057 LASONIC 058 MOBILE AUTHORITY MEMOREX 055 MALATA 056 MAGNAVOX 076 093 MINTEK 074 094 MONYKA 073 NORCENT 048 049 050 NEXT BASE 052 NEC 053 NANTAUS 144 NESA 074 OPTOMEDIA ELECTRONICS OPTIVIEW 072 ONKYO 076 092 119 PHILCO 044 045 PRINCETON 046 047 PROSCAN 023

054

105

English - 21

DVD

Brand Code

PANASONIC 024 034 124 134 136 137 138 PHILIPS 036 076 ROTEL 117 118 RIO 120 RCA 023 035 074 075 131 132 RAITE 073 ROWA 038 SAMPO 104 SONY 026 029 126 127 128 129 130 141 SHERWOOD 039 041 SVA 042 SYLVANIA 043 093 SHARP 140 SANSUI 062 SANYO 062 090 SHINSONIC 094

SAMSUNG SET-TOP BOX

Product Code

Ground wave STB 001 002 Satellite STB 003 CABLE STB 004 STB DVD COMBO 008 Satellite STB HDD COMBO Standard 009

SET-TOP BOX

Brand Code

ALPHASTAR 023 ANAM 043 CHANNEL MASTER 018 034 CROSSDIGITAL 019 CHAPARRAL 035 DIRECT TV 015 016 017 019 022 045 060 061 062

DAEWOO 074 DISH NETWORK SYSTEM DISHPRO 069 DRAKE 018 024 032 DX ANTENNA 027 ECHOSTAR 025 069 070 071 EXPRESSVU 069 GOI 069 GE 065 GENERAL INSTRUMENT HTS 069 HOME CABLE 056 HITACHI 022 HUGHES NETWORK IQ 020 IQ PRISM 020 JANEIL 059 JERROID 063 JVC 069 070 LG(Goldstar) 044 073

065 066 067 068

069 070

046 047 048 063 064

015 017

Brand Code

THOMSON 145 TOSHIBA 028 062 076 TECHNICS 139 TVIEW 072 TOKAI 073 TEAC 096 TECHWOOD 097 TREDEX 098 099 101 URBAN CONCEPTS VENTURER 075 VOCOPRO 102 YAMAHA 032 063 YAMAKAWA 040 073 XWAVE 103 ZENITH 076 121

Product Code

Satellite STB HDD COMBO Premium 010 CABLE STB HDD COMBO Standard 011 CABLE STB HDD COMBO Premium 012 Ground wave STB HDD COMBO Standard 013 Ground wave STB HDD COMBO Premium 014

Brand Code

MAGNAVOX 016 021 036 038 039 040 041 042 MEMOREX 016 MOTOROLA 064 MACOM 018 MITSUBISHI 015 NEXT LEVEL 047 048 064 PHILIPS 015 016 017 021 033 036 038 039 040

PRIMESTAR 046 049 050 063 PANASONIC 058 059 061 062 PAYSAT 016 PROSCAN 065 066 RCA 051 052 053 065 066 RADIOSHACK 064 REALISTIC 057 STAR TRAK 026 STS 020 027 SKY 031 SKY LIFE 005 006 007 SHACK 064 STAR CHOICE 064 SONY 054 060 TOSHIBA 015 017 028 029 030 072 ULTIMATE TV 060 066 UNIDEN 016 021 037 055 056 057 ZENITH 024 031 068

076

041 042 067

English - 22

To Select the Source (depending on the model)

Use to select TV or other external input sources connected to the TV.

Use to select the input source of your choice.

Press the MENU button to display the menu.

Press the▲ or ▼ buttons to select “Input”, then press the ENTER button.

Press the ENTER button to select “Source List”.

Press the ▲ or ▼ buttons to select signal source, then press the ENTER button.

When you connect equipment to the LCD, you can choose between the following sets of jacks: TV, AV1, AV2, S-Video1, S-Video2, Component1, Component2, PC, HDMI1, HDMI2, HDMI3 on the TV’s rear panel. HDMI1, HDMI2, HDMI3 input can only be selected when the external device is turned on and connected via HDMI. 23,26 inch model supports TV, AV1, AV2, S-Video1,S-Video 2, Component1, Component 2, PC, HDMI1, and HDMI2 only.

AV2/S-Video2/HDMI3 is placed on the side of the TV.

You can choose only those external devices that are connected to the TV.

Press the SOURCE button on the remote control to view an external signal source.

To Edit the Input Source Name (depending on the model)

Name the device connected to the input jacks to make your input source selection easier.

1. Press the MENU button to display the menu.

Press the▲ or ▼ buttons to select “Input”, then press the ENTER button. Press the ▲ or ▼ buttons to select “Edit Name”, then press the ENTER

button.

Source List : TV ► Edit Name WISELINK Anynet+ (HDMI-CEC)

AV1 : ---AV2 : ---S-Video1 : ---S-Video2 : ---Component1 : ---Component2 : ----

▼More

Source List : TV ► Edit Name WISELINK Anynet+ (HDMI-CEC)

Input

Move Enter Return

Source ListTV

Move Enter Return

Input

►

2. Press the ▲ or ▼ buttons to select “AV1”, “AV2”, “S-Video1”, “S-Video2”,

"Component1”, “Component2”, “PC”, “HDMI1”, “HDMI2”, “HDMI3” input jack, then press the ENTER 23,26 inch model supports TV, AV1, AV2, S-Video1,S-Video 2, Component1,

button.

Component 2, PC, HDMI1, and HDMI2 only.

Press the ▲ or ▼ buttons to select “VCR”, “DVD”, “D-VHS”, “Cable STB”, "HD STB”, “Satellite STB”, “PVR STB”, “AV Receiver”, “DVD Receiver”, "Game”, “Camcorder”, “DVD Combo”, “PC”, “VOD STB”, “TV” input source, then press the ENTER button. Press the EXIT button to exit.

English - 23

Move Enter Return

Edit NameTV

AV1 AV2 : ---S-Video1 : ---S-Video2 : ---Component1 : ---Component2 : ----

▼More

Move Enter Return

AV1

AV2 : ---- S-Video1 : ---- S-Video2 : ---- Component1 : ---- Component2 : ----

▼More

Move Enter Return

Edit NameTV

: ----

----

: ----

VCR DVD D-VHS Cable STB HD STB Satellite STB PVR STB

▼

Picture Control

Using Automatic Picture Settings

Your TV has Three automatic picture settings ("Dynamic”, “Standard”, “Movie") that are preset at the factory. You can activate either Dynamic, Standard, Movie by making a selection from the menu.

Press the MENU button to display the menu.

Press the ENTER button, to select “Picture”.

Press the ENTER button to select “Mode”.

Press the ENTER button again. Press the ▲ or ▼ buttons to select the “Dynamic”, “Standard”, “Movie” picture setting. Press the ENTER button.

 Choose Dynamic to increase the clarity and sharpness of the picture.  Choose Standard for the standard factory settings.  Choose Movie for a natural Image without picture enhancements.

3. Press the ▲ or ▼ buttons to select “Contrast”, “Brightness”, “Sharpness”, "Color”, or “Tint(G/R)”, then press the ENTER button.

Press the ◄ or ► buttons to decrease or increase the value of a particular item.

For example, if you select “Contrast”, pressing the ► button increases it.

Press the EXIT

button to exit.

• When you make changes to Contrast, Brightness, Sharpness, Color, Tint(G/R) OSD will be also adjusted accordingly.

• When in PC mode, Tint, Sharpness, and Color are not available.

Mode : Dynamic Contrast 100 Brightness 45 Sharpness 75 Color 55 Tint G 50 R 50 Backlight 10

▼More

Move Enter Return

Mode : Dynamic

Contrast 100 Brightness 50 Sharpness 85 Color 55 Tint G 50 R 50 Backlight 10

▼More

Move Enter Return

Mode : Dynamic Contrast 100 Brightness 50 Sharpness 85 Color 55 Tint G 50 R 50 Backlight 10

▼More

Move Enter Return

▲

Contrast

▼

Move Adjust Return

PictureTV

Dynamic

Standard Movie

PictureTV

►

100

Press the P.MODE button on the remote control repeatedly to select the desired picture mode.

English - 24

Activating Backlight

You can adjust the screen brightness by adjusting the LCD backlight brightness. (0~10)

1. Press the MENU button to display the menu. Press the ENTER button, to select “Picture”.

Press the ▲ or ▼ button to select “Backlight”, then press the ENTER button.

Press the ◄ or ► button to decrease or increase the value of the backlight brightness. Press the ENTER button.

Press the EXIT button to exit.

Adjusting the Color Tone

You can change the color of the entire screen according to your preference.

Press the MENU button to display the menu. Press the ENTER button to select “Picture”.

2. Press the ▲ or ▼ buttons to select “Color Tone”, then press the ENTER button.

3. Press the ▲ or ▼ buttons to select “Cool2”, “Cool1”, “Normal”, “Warm1”,

or “Warm2”. Press the ENTER button.

When the picture mode is set to Dynamic or Standard, Warm1 and Warm2 cannot be selected. Movie mode is only available .

Mode : Dynamic Contrast 100 Brightness 50 Sharpness 85 Color 55 Tint G 50 R 50 Backlight 10

▼More

▲

Backlight

▼

▲More

Color Tone : Cool2

Detailed settings

Size : 16 : 9 Digital NR : Low Active Color : On DNle : On Reset : OK

▲More

Color Tone : Cool1

Detailed settings

Size : 16 : 9 Digital NR : Low Active Color : On DNle : On Reset : OK

PictureTV

Move Enter Return

Move Adjust Return

PictureTV

►

Move Enter Return

PictureTV

Cool2

Cool1 Normal

Warm1 Warm2

Move Enter Return

►

► ► ► ►

Resetting the Picture Settings to the Factory Defaults

Press the ▲ or ▼ buttons to select “Reset”, then press the ENTER button.

Press the ▲ or▼ button to select “OK”, or “Cancel”, then press the ENTER button. Press the EXIT

button to exit.

Each mode can be reset.

English - 25

▲More

Color Tone : Cool1

Detailed settings

Size : 16 : 9 Digital NR : Low Active Color : On DNle : On

Reset : OK

PictureTV

Cancel

Move Enter Return

Adjusting the Detailed Settings

You can set detail picture settings.

Activating Detailed Settings

1. Press the MENU button to display the menu. Press the ENTER button, to select “Picture”.

Press the ENTER button to select “Mode”

Press the ▲ or ▼ buttons to select “Movie”, then press the ENTER button.

Press the ▲ or ▼ buttons to select “Detailed settings”,

then press the ENTER button. Picture Mode is available in Standard or Movie mode. If DNIe is Off, the Detailed Settings cannot be selected when the Picture mode is in Standard mode.

Activating Black adjust

You can directly select the black level on the screen to adjust the screen depth.

Press the ▲ or ▼ button to select “Black adjust”, then press the ENTER

button.

Press the ▲ or ▼ button to select “Off”,“Low”,“Medium”,“High”.

5. Press the ENTER button.

 Off: Turns off the black adjustment function.  Low: Sets the black color depth to low.  Medium: Sets the black color depth to medium.  High: Sets the black color depth to high.

Mode : Movie Contrast 80 Brightness 45 Sharpness 20 Color 45 Tint G 50 R 50 Backlight 5

▼More

Move Enter Return

▲More

Color Tone : Warm2 Detailed settings Size : 16 : 9 Digital NR : Low

Active Color : On DNle : On

Reset : OK

Move Enter Return

Black Adjust : Off Dynamic Contrast : Off Gamma : Color Space : Auto White Balance My Color Control Edge Enhancement : Off

Move Enter Return

Black Adjust : Off

Dynamic Contrast : Off Gamma : 0 Color Space : Auto White Balance My Color Control Edge Enhancement : Off

Move Enter Return

PictureTV

►

Detailed SettingsTV

Detailed Settings

Off

Low Medium High

►

► ► ► ►

► ►

► ► ► ►

Activating Dynamic Contrast

You can adjust the screen contrast so that the optimal contrast is provided.

Press the ▲ or ▼ button to select “Dynamic Contrast”, then press the ENTER

button.

Press the ▲ or ▼ button to select “Off”,“Low”,“Medium”,“High”.

Press the ENTER button.

 Off: Turns off the dynamic contrast adjustment function.  Low: Sets the dynamic contrast to low.  Medium: Sets the dynamic contrast to medium.  High: Sets the dynamic contrast to high.

English - 26

Detailed SettingsTV

Black Adjust : Off Dynamic Contrast : Off Gamma : 0 Color Space : Auto White Balance My Color Control Edge Enhancement : Off

Move Enter Return

Detailed SettingsTV

Black Adjust : Off

Dynamic Contrast : Off

Gamma : 0 Color Space : Auto White Balance My Color Control Edge Enhancement : Off

Move Enter Return

Off

Low Medium High

► ►

► ► ► ►

Activating Gamma

You can adjust the middle brightness of pictures. (-3 ~ 3)

Press the ▲ or ▼ button to select “Gamma”, then press the ENTER

button.

Press the ◄ or ► button to decrease or increase the value of a particular item.

Press the ENTER button.

Detailed SettingsTV

Black Adjust : Off Dynamic Contrast : Off Gamma : Color Space : Auto White Balance My Color Control Edge Enhancement : Off

Move Enter Return

► ►

► ► ► ►

Changing the Color Space

Color space is a color matrix composed of red, green, and blue colors. Select your favorite color space to and experience the most natural color.

10.

Press the ▲ or ▼ button to select “Color Space”, then press the ENTER button. Press the ▲ or ▼ button to select “Wide” or “Auto”.

11. Press the ENTER button.

 Wide : Wide Color Space offers deep and rich color tone.  Auto : Auto Color Space automatically adjusts to the most natural color tone based on

program sources.

Activating White Balance

You can adjust the color temperature for more natural picture colors.

Press the ▲ or ▼ button to select “White Balance”, then press the ENTER

12.

button.

Select the required option by pressing the ▲ or ▼ button, then press the

13. ENTER button.

14.

Press the ◄ or ► button to decrease or increase the value of a particular item.

Press the ENTER button.

 R offset: Adjusts the red color darkness.  G offset: Adjusts the green color darkness.  B offset: Adjusts the blue color darkness.  R gain: Adjusts the red color brightness.  G gain: Adjusts the green color brightness.  B gain: Adjusts the blue color brightness.  Reset: The previously adjusted white balance will be reset to the factory defaults.

Changing the adjustment value will refresh the adjusted screen.

Gamma

Adjust Return

Black Adjust : Off Dynamic Contrast : Off Gamma : Color Space : Auto White Balance My Color Control Edge Enhancement : Off

Move Enter Return

Black Adjust : Off Dynamic Contrast : Off Gamma :

Color Space : Auto

White Balance My Color Control Edge Enhancement : Off

Move Enter Return

Black Adjust : Off Dynamic Contrast : Off Gamma : Color Space : Auto White Balance My Color Control Edge Enhancement : Off

Move Enter Return

R-Offset 15 G-Offset 15 B-Offset 15 R-Gain 15 G-Gain 15 B-Gain 15 Reset

Move Enter Return

▲

R-Offset

▼

Move Adjust Return

Detailed SettingsTV

White BalanceTV

Auto

Wide

► ►

► ► ► ►

► ►

► ► ► ►

English - 27

Activating My Color Control

This setting can be adjusted to suit your personal preferences. When using the My Color Control Feature, the current picture remains in movement.

15.

Press the ENTER button to select “My Color Control”.

16.

Press the ▲ or ▼ button to select “Pink”,“Green”,“Blue”,“White”,“Reset”.

Press the ENTER button.

17.

Press the ◄ or ► button to decrease or increase the value of a particular item.

Press the ENTER button.

 Pink: Darkens or lightens the pink color  Green: Darkens or lightens the green color  Blue: Darkens or lightens the blue color  White: Darkens or lightens the white color  Reset: The previously adjusted colors will be reset to the factory defaults.

Changing the adjustment value will refresh the adjusted screen.

▲

Pink

▼

Detailed SettingsTV

Black Adjust : Off Dynamic Contrast : Off Gamma : Color Space : Auto White Balance My Color Control Edge Enhancement : Off

Move Enter Return

Pink 15 Green 15 Blue 15 White 15 Reset

Move Enter Return

Move Adjust Return

My Color ControlTV

► ►

► ► ► ►

Activating Edge Enhancement

You can emphasize object boundaries in the picture.

18. Press the ▲ or ▼ button to select “Edge Enhancement”, then press the ENTER button.

19.

Press the ▲ or ▼ button to select “Off” or “On”.

Press the ENTER button. Press the EXIT

button to exit.

Detailed SettingsTV

Black Adjust : Off Dynamic Contrast : Off Gamma : Color Space : Auto White Balance My Color Control Edge Enhancement : Off

Move Enter Return

Black Adjust : Off Dynamic Contrast : Off Gamma : Color Space : Auto White Balance My Color Control

Edge Enhancement : O

Move Enter Return

Detailed SettingsTV

Off

► ►

► ► ► ►

English - 28

+ 161 hidden pages