SAMSUNG LN46A860S2F User Manual

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.

Contacte con SAMSUNG WORLDWIDE

Si tiene alguna pregunta o comentario referente a nuestros productos, por favor contacte con nuestro Servicio de Atención al Cliente.

Country

CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca

U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com/us

Customer Care Center

Web Site Address

Samsung Electronics Canada Inc., Customer Service 55 Standish Court Mississauga, Ontario L5R 4B2 Canada

Samsung Electronique Canada Inc., Service à la Clientèle 55 Standish Court Mississauga, Ontario L5R 4B2 Canada

Samsung Electronics America, Inc. 105 Challenger Road Ridgefield Park, NJ 07660-0511

LCD TV

user manual

BN68-01691A-02

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service, please register your product at

www.samsung.com/global/register

Model Serial No.

Important Warranty Information Regarding Television Format Viewing

Wide screen format LCD Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format

full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to ll the screen if

your model offers this feature and the images are constantly moving. Displaying stationary graphics and images on screen, such as the dark sidebars on nonexpanded standard format television video and programming, should be limited to no more than 5% of the total television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary images that exceed the above guidelines can cause uneven aging of LCD Displays that leave subtle, but permanent burned-in ghost images in the LCD picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars.

On LCD models that offer picture sizing features, use these controls to view different formats as a full screen picture. Be careful in the selection and duration of television formats used for viewing. Uneven LCD aging as a result of format selection and use, as

well as burned-in images, are not covered by your Samsung limited warranty.

SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY STATEMENT

Subject to the requirements, conditions, exclusions and limitations of the original Limited Warranty supplied with Samsung Electronics (SAMSUNG) products, and the requirements, conditions, exclusions and limitations contained herein, SAMSUNG will additionally provide Warranty Repair Service in the United States on SAMSUNG products purchased in Canada, and in Canada on SAMSUNG products

purchased in the United States, for the warranty period originally specied, and to the Original Purchaser only.

The above described warranty repairs must be performed by a SAMSUNG Authorized Service Center. Along with this Statement, the Original Limited Warranty Statement and a dated Bill of Sale as Proof of Purchase must be presented to the Service Center. Transportation to and from the Service Center is the responsibility of the purchaser.

Conditions covered are limited only to manufacturing defects in material or workmanship, and only those encountered in normal use of the product.

Excluded, but not limited to, are any originally specied provisions for, in-home or on-s

exchanges or replacements, accessories, options, upgrades, or consumables.

For the location of a SAMSUNG Authorized Service Center, please call toll-free:

In the United States : 1-800-SAMSUNG (1-800-726-7864) In Canada : 1-800-SAMSUNG

See the warranty card for more information on warranty terms.

➣

Precautions When Displaying a Still Image

A still image may cause permanent damage to the TV screen

Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention. This image

• retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

•

Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the left,

right and center of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause a similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.

ite services, minimum or maximum repair

times,

Contents

English

General Information

List of Features ..................................................................3

■

Accessories .......................................................................3

■

Viewing the Control Panel .................................................4

■

Viewing the Connection Panel ...........................................5

■

Remote Control .................................................................7

■

Mini Remote Control ..........................................................8

■

Installing Batteries in the Remote Control .........................8

■

Using the Remote Control Backlight Buttons ....................9

■

Connections

Connecting VHF and UHF Antennas .................................9

■

Connecting Cable TV ......................................................10

■

Connecting a DVD/Blu-Ray player or Cable Box/Satellite

■

receiver (Set-Top Box) via HDMI .....................................11

Connecting a DVD/Blu-Ray player or Cable Box/Satellite

■

receiver (Set-Top Box) via DVI ........................................11

Connecting a DVD/Blu-Ray player or Cable Box/Satellite

■

receiver (Set-Top Box) via Component cables ................12

Connecting a Camcorder .................................................12

■

Connecting a VCR ...........................................................13

■

Connecting a Digital Audio System .................................14

■

Connecting an Amplier/DVD Home Theater ..................14

■

Connecting a PC .............................................................15

■

Operation

Turning the TV On and Off ..............................................16

■

Plug & Play Feature .........................................................16

■

Changing Channels .........................................................18

■

Adjusting the Volume .......................................................18

■

Viewing the Display .........................................................19

■

Viewing the Menus ..........................................................19

■

Using the TOOLS Button .................................................20

■

Memorizing the Channels ................................................20

■

Setting Up Your Remote Control .....................................22

■

Remote Control Codes ....................................................24

■

To Select the Source .......................................................27

■

To Edit the Input Source Name ........................................27

■

Picture Control

Changing the Picture Standard .......................................28

■

Customizing the Picture Settings .....................................28

■

Adjusting the Detailed Settings ........................................29

■

Resetting the Picture Settings to the Factory Defaults ....32

■

Conguring Picture Options .............................................33

■

Viewing Picture-in-Picture ...............................................38

■

Sound Control

Changing the Sound Standard ........................................40

■

Customizing the Sound ...................................................40

■

Setting the TruSurround XT .............................................41

■

Choosing Preferred Language ........................................42

■

Choosing a Multi-Channel Sound (MTS) track ................42

■

Automatic Volume Control ...............................................43

■

Selecting the Speaker .....................................................43

■

Listening to the Sound of the Sub (PIP) Picture ..............44

■

Resetting the Sound Settings to the Factory Defaults .....45

■

Connecting Headphones (Sold separately) .....................45

■

Channel Control

Managing Channels .........................................................46

■

Clearing Scrambled Channels - Digital ............................53

■

Fine Tuning Analog Channels ..........................................53

■

Checking the Digital-Signal Strength ...............................54

■

PC Display

Using Your TV as a Computer (PC) Display ....................55

■

Display Modes .................................................................55

■

Setting up the TV with your PC .......................................56

■

Time Setting

Setting the Clock .............................................................58

■

Function Description

Selecting a Menu Language ............................................62

■

Using the V-Chip ..............................................................62

■

Viewing Closed Captions (On-Screen Text Messages)

■

- Analog ...........................................................................69

Viewing Closed Captions (On-Screen Text Messages)

■

- Digital ............................................................................70

Adjusting the TV On/Off Melody Sound ...........................71

■

Setting the Light Effect ....................................................71

■

Setting the Entertainment mode ......................................72

■

Using the Energy Saving Feature ....................................72

■

Upgrading the Software

■

Self diagnosis .................................................................74

■

...................................................73

WISELINK Pro

Using the WISELINK Pro Function ..................................75

■

Using the Photo List ........................................................77

■

Sorting Photo List ............................................................78

■

Viewing a Photo or Slide Show ......................................83

■

Using the Music List ........................................................87

■

Sorting Music List ............................................................88

■

Playing a Music File .........................................................92

■

Using the Movie List ........................................................94

■

Sorting Movie List ............................................................95

■

Playing a Movie File ........................................................98

■

Picture/Music Settings Using WISELINK .......................100

■

Using the Setup Menu ...................................................100

■

WISELINK Pro-DLNA

Setting the DLNA Network .............................................102

■

Installing the DLNA Application ......................................103

■

Using the DLNA Application ...........................................104

■

Using the DLNA Function ..............................................109

■

Content Library

Using the Content Library .............................................. 111

■

Using the TV Memory Contents ....................................112

■

Using Additional Content Using External USB Memory

■

Storage

..........................................................................117

English - 1

Network Settings and InfoLink

Network Connection - Cable ..........................................118

■

Network Connection - Wireless .....................................120

■

Network selection ..........................................................120

■

Cable Network Setup .....................................................121

■

Wireless Network Setup ................................................123

■

Using InfoLink ................................................................126

■

InfoLink Setup ................................................................129

■

Product Guide ................................................................130

■

About Anynet+

What is Anynet+?...........................................................131

■

Connecting Anynet+ Devices.........................................131

■

Setting Up Anynet+ .......................................................132

■

Scanning and Switching between Anynet+ Devices ......133

■

Recording ......................................................................134

■

Listening through a Receiver (Home theater) ................134

■

Troubleshooting for Anynet+ .........................................135

■

Appendix

Troubleshooting .............................................................136

■

Installing the Stand ........................................................138

■

Disconnecting the Stand ................................................138

■

Auto Wall-Mount Adjustment (Sold separately) ............139

■

Wall Mount Kit Specications (VESA) ...........................140

■

Using the Anti-Theft Kensington Lock ...........................141

■

Securing the TV to the Wall ...........................................142

■

Specications ................................................................143

■

Dimensions ....................................................................144

■

Symbol Press Note One-Touch Button

English - 2

English - 3

General Information

List of Features

Adjustable picture settings that can be stored in the TV’s memory.

• Automatic timer to turn the TV on and off.

• A special sleep timer.

• Excellent Digital Interface & Networking :

• With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Cable Box/Satellite receiver (Set-Top Box) needed.

You can view News, Weather, and Stock information over the network (SAMSUNG InfoLink’s Service).

•

You can listen to music les and view pictures on USB Mass Storage Class (MSC) devices.

•

HDMI/DVI connection of your PC to this TV.

• Excellent Picture Quality

•

- DNIe technology provides life-like clear images. SRS TruSurround XT

•

- SRS TruSurround XT provides a virtual surround system.

Accessories

Please make sure the following items are included with your LCD TV. If any items are missing, contact your dealer.

Remote Control & Batteries

➣

(AAA x 2)

(BN59-00700A)

Power Cord

(3903-000144)

The items color and shape may vary depending on the model.

Mini Remote Control &

Lithium battery (3V x 1ea)

(BN59-00788B)

Cleaning Cloth

(BN63-01798B)

Owner’s Instructions

Warranty Card /

Registration Card /

Safety Guide Manual

(Not available in all locations)

Cover-Bottom

(LN46A850S1F, LN46A860S2F: BN63-04822B) (LN52A850S1F, LN52A860S2F: BN63-04822B)

Program CD

(

BN59-00726A

)

Viewing the Control Panel

1 2 3 4 5

Buttons on the Lower-Right Part of the Panel

The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu.

To use the more advanced features, you must use the remote control.

Front Panel buttons

Touch each button to operate.

The product color and shape may vary depending on the model.

➣

SOURCE

Toggles between all the available input sources (TV, AV1, AV2, S-Video, Component1, Component2, PC, HDMI1, HDMI2/DVI, HDMI3, HDMI4). In the onscreen menu, use this button as you would use the ENTER button on the remote control.

Press to see an on-screen menu of your TV’s features.

– VOL +

Press to increase or decrease the volume. In the on-screen menu, use the – VOL + buttons as you

would use the ◄ and ► buttons on the remote control.

Press to change channels. In the on-screen menu, use the CH buttons as

you would use the ▼ and ▲ buttons on the remote

control.

(Power)

Press to turn the TV on and off.

POWER INDICATOR

Blinks and turns off when the power is on and lights up in stand-by mode.

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

SPEAKERS

English - 4

English - 5

Viewing the Connection Panel

HDMI IN4

Use the connection panel jacks to connect A/V components that will be connected continuously, such as DVD/Blu-Ray players or a VCR. For more information on connecting equipment, see pages 9~15.

[LN46A850S1F, LN52A850S1F]

[TV Rear Panel]

[LN46A860S2F, LN52A860S2F]

[TV Side Panel]

➣

The product color and shape may vary depending on the model.

AUDIO OUT

Connects to the audio input jacks on your Amplier/Home theater.

DIGITAL AUDIO OUT (OPTICAL)

Connects to a Digital Audio component.

PC IN [PC] / [AUDIO]

Connects to the video and audio output jacks on your PC.

HDMI IN 1, 2, 3, 4 / DVI IN(HDMI2)[R-AUDIO-L]

Connects to the HDMI jack of a device with an HDMI output.

- No sound connection is needed for an HDMI to HDMI connection. Use the HDMI IN 2 jack for DVI connection to an external device. Use a DVI to HDMI cable or DVI-HDMI adapter (DVI to HDMI) for video connection and the DVI IN (HDMI2) [R-AUDIO-L] jacks for audio.

- When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.

ANT IN

Connects to an antenna or cable TV system.

WISELINK

Connect a USB mass storage device to view movies and photos and listen to music les. You can connect to Samsung’s network wirelessly using the Wireless Infolink adapter (Sold separately).

AV IN 2

Video and audio inputs for external devices, such as a camcorder or VCR.

(HEADPHONE)

Connects a set of external headphones for private listening.

POWER INPUT

Connects the supplied power cord.

S-VIDEO

Connects an S-Video signal from a camcorder or VCR.

- Use the AV IN 1 [R-AUDIO-L] jacks for audio.

COMPONENT IN 1, 2 / AV IN 1

Connects Component video/audio. The COMPONENT IN 1 jack is also used as the AV IN 1 jack.

- Connect the video cable to the COMPONENT IN 1 [Y/VIDEO] jack and the audio cable to the COMPONENT IN 1 [R-AUDIO-L] jacks.

LAN

Connect a LAN cable to this port to connect to the Network (SAMSUNG InfoLink’s Service). (See pages 118~119)

EX-LINK

Connect this to the jack on the optional wall mount bracket. This will allow you to adjust the TV viewing angle using your remote control.

KENSINGTON LOCK

The Kensington Lock (optional) is a device used to physically x the system when used in a public place. If you want to

use a locking device, contact the dealer where you purchased the TV.

➣

The location of the Kensington Lock may be different depending on its model.

English - 6

English - 7

SET RESET

VCR DVD STB

4 5

( )

e f g h

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always point it directly at the TV. You can also use your remote control to operate your VCR, DVD/Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box)

POWER

Turns the TV on and off.

Selects the TV mode directly.

NUMERIC BUTTONS

Press to directly select the channel.

Press to select additional channels (digital and analog) being broadcast by the same station. For example, to select channel “54-3”, press “54”, then press “

(MUTE)

Press to temporarily cut off the sound.

VOL – / VOL +

Press to increase or decrease the volume.

CH LIST

Used to display Channel Lists on the screen.

TOOLS

Use to quickly select frequently used functions.

INFO

Press to display information on the TV screen.

COLOR BUTTONS

Use these buttons in the Channel list, WISELINK Pro, etc.

Controls the caption decoder.

E.MODE

Press to select the preset display and sound modes for sports, cinema and games.

Use these buttons in the DMA,

WISELINK Pro and Anynet+ modes. ( used to control recording on Samsung recorders with the Anynet+ feature)

SET

Sets the remote to control your TV, VCR, DVD or Set-Top Box

MODE

Press to operate your TV, DVD, STB or VCR (See pages 22~26)

Press to backlight the buttons on the remote. This function is convenient for using at night or when the room is dark. (Using the remote control with the ON/OFF light button set to On will reduce the battery usage time.) (See page 9)

” and “3”.

: This remote can be

ON/OFF

PRE-CH

Tunes to the previous channel.

CH / CH

Press to change channels.

(

SOURCE

Press to display and select the available video sources.

)

W.LINK (WISELINK Pro)

This function enables you to view and play photo, music and

movie les from an external

device. (Refer to pages 77 (Photo), 87 (Music) and 94 (Movie))

Displays the main on-screen menu.

RETURN

Returns to the previous menu.

 UP▲/DOWN▼/LEFT◄/

RIGHT►/ENTER

Press the Up/Down/Left/Right sections of the wheel button and Enter to select on-screen menu items and change menu values. You can navigate up and down the menu, switch channels and adjust the volume by turning the wheel button. (See pages 18~19)

EXIT

Press to exit the menu.

DMA (Digital Media Adapter)

Use this when connecting a SAMSUNG DMA device through an HDMI interface and switching to DMA mode. For more information on the operating procedures, refer to the user manual of the DMA. This button is available when “Anynet+(HDMI-CEC)” is “On”. (see page 132)

INFO.L

Press to use the News, Stock Market and Weather Forecast information services available over Samsung’s network. (see page 126)

FAV.CH

Press to switch to your favorite channels. (see page 48)

CONTENT

This function enables you to view “Content Library”. (see page 111)

RESET

When your remote does not work, change the batteries and press the RESET button for 2-3 seconds before use.

The performance of the remote control may be affected by bright light.

➣

Mini Remote Control

3 3

The Mini Remote Control is a simplied remote control that consists of the power, channel

and volume buttons only.

Television Standby button

This button only works when you press it for longer than 1.5 seconds.

➣

: Next channel

: Previous channel

+ : Volume increase

– : Volume decrease

IrDA transmitter

Use the Mini Remote Control so that this part faces the TV.

➣

Installing Batteries in the Remote Control

Normal Remote Control

Lift the cover at the back of the remote control upward as shown in the gure.

2. Install two AAA size batteries.

Make sure to match the “+” and “–” ends of the batteries with the diagram inside the

➣

compartment.

Replace the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the

➣

remote control for a long time.

The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the batteries should last for about one year.)

Using the remote control with the

➣

battery usage time.

Mini Remote Control

Turn the battery cover counterclockwise to unlock it and then separate the battery cover.

2. Insert the corresponding 3V Lithium battery.

3. Place the battery cover into the remote control aligning it with the grooves and then turn the

battery cover clockwise to lock the cover.

If the remote control doesn’t work, check the following:

➣

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage or is the power cord unplugged?

5. Is there a special uorescent light or neon sign nearby?

ON/OFF light button set to On will reduce the

English - 8

English - 9

Using the Remote Control Backlight Buttons

Use this feature in dark surroundings and when you are unable to see the remote control buttons clearly.

Press the

Pressing the

➣

When ON, the button backlight is turned on for a moment.

➣

Pressing a remote control button when the remote control is on turns the button backlight on for a moment. If

➣

ON/OFF light button.

ON/OFF light button toggles between ON and OFF.

you touch or move the remote control and the motion is detected by the sensor of the remote control, the button backlight will be turned on for a moment.

Since there is a vibrating device inside the remote control, shaking the remote control will result in a sound

➣

generated by the device.

The button backlight will not be turned on when the remote control is turned off.

➣

Connections

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like the diagram to the right, see “Antennas

with 300 Ω Flat Twin Leads” below.

If your antenna has one lead that looks like the diagram to the right, see “Antennas with

75 Ω Round Leads”.

If you have two antennas, see “Separate VHF and UHF Antennas”.

Antennaswith300ΩFlatTwinLeads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300

Ω twin at leads, follow the directions below.

Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not

supplied). Use a screwdriver to tighten the screws.

ANT IN

Plug the adaptor into the ANT IN terminal on the back of the TV.

Antennaswith75ΩRoundLeads

ANT IN

1. Plug the antenna lead into the ANT IN terminal on the back of the TV.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

Connect both antenna leads to the combiner.

UHF

VHF

2. Plug the combiner into the ANT IN terminal on the bottom of the rear panel.

ANT IN

UHF

VHF

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

Plug the incoming cable into the ANT IN terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view

➣

unscrambled cable channels.

Connecting to a Cable Box that Descrambles All Channels

Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.

➣

Connect the other end of this cable to the ANT IN terminal on the back of the TV.

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch and four lengths of RF cable. (These items are available at most electronics stores.)

Find and disconnect the cable that is

connected to the ANT IN terminal on your cable box.

This terminal might be labeled

➣

“ANT IN”, “VHF IN” or simply, “IN”.

ANT IN

Incoming

cable

ANT IN

ANT OUT

ANT IN

Splitter

Connect this cable to a two-way

splitter.

Connect an RF cable between the

Incoming

cable

Splitter

Cable Box

OUTPUT terminal on the splitter and the IN terminal on the cable box.

Connect an RF cable between the

Incoming

cable

Splitter

Cable Box

RF (A/B)

Switch

ANT OUT terminal on the cable box and the B–IN terminal on the RF(A/B) switch.

5. Connect another cable between the other OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch.

Connect the last RF cable between the OUT terminal on the RF (A/B) switch and the ANT IN terminal on the rear of the

Incoming

cable

Incoming

cable

Splitter

Cable Box

RF (A/B)

Switch

RF (A/B)

Switch

ANT IN

TV Rear

TV.

After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)

English - 10

English - 11

Connecting a DVD/Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box) via HDMI

HDMI IN4

This connection can only be made if there is an HDMI Output connector on the external device.

1. Connect an HDMI Cable between the HDMI IN (1, 2, 3 or 4) jack on the TV and the HDMI jack on the DVD/BluRay player or Cable Box/Satellite receiver (Set-Top Box).

DVD/Blu-Ray player or Cable Box/Satellite

receiver (Set-Top Box) Rear Panel

TV Rear Panel

TV Side Panel

What is HDMI?

➣

HDMI Cable (Not supplied)

• HDMI(High-Denition Multimedia Interface), is an interface that enables the

transmission of digital audio and video signals using a single cable.

• The difference between HDMI and DVI is that the HDMI device is smaller in size and has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed. DVI also requires a separate audio connection (see below).

Each DVD/Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box) has a different

➣

back panel conguration.

The TV may not output sound and pictures may be displayed with abnormal color when

➣

DVD/Blu-Ray players/Cable Boxes/Satellite receivers supporting HDMI versions older than 1.3 are connected. When connecting an older HDMI cable and there is no sound, connect the HDMI cable to the HDMI IN 2 jack and the audio cables to the DVI IN (HDMI2) [R-AUDIO-L] jacks on the back of the TV. If this happens, contact the company

that provided the DVD/Blu-Ray player/Cable Box/Satellite receiver to conrm the HDMI

version, then request an upgrade.

HDMI cables that are not 1.3 may cause annoying icker or no screen display

➣

Connecting a DVD/Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box) via DVI

This connection can only be made if there is a DVI Output connector on the external device.

1. Connect a DVI to HDMI Cable or DVI-HDMI Adapter between the HDMI IN 2 jack on the TV and the DVI jack on the DVD/Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box).

DVD/Blu-Ray player or Cable Box/

Satellite receiver (Set-Top Box)

TV Rear Panel

Connect Audio Cables

between the DVI IN (HDMI 2) [R-AUDIO-L] jack on the TV and the DVD/Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box).

Audio Cable (Not supplied)

DVI to HDMI Cable (Not supplied)

Each DVD/Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box) has a different

➣

back panel conguration.

When connecting a DVD/Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box),

➣

match the color of the connection terminal to the cable.

When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.

➣

HDMI IN4

Connecting a DVD/Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box) via Component cables

The rear panel jacks on your TV make it easy to connect a DVD/Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box) to your TV.

1. Connect a Component Cable between the COMPONENT IN (1 or 2) [Y, PB, PR] jacks on the TV and the COMPONENT [Y, PB, PR] jacks on the DVD/Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box).

Connect Audio Cables between the COMPONENT IN(1 or 2) [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the DVD/ Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box).

DVD/Blu-Ray player or Cable Box /

Satellite receiver (Set-Top Box)

Audio Cable

(Not supplied)

Component Cable (Not supplied)

Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and

➣

Pr (Red) for enhanced video quality. Be sure to match the component video and audio connections. For example, if connecting a Component video cable to COMPONENT IN 1, connect the audio cable to COMPONENT IN 1 also.

Each DVD/Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box) has a different

➣

back panel conguration.

When connecting a DVD/Blu-Ray player or Cable Box/Satellite receiver (Set-Top Box),

➣

match the color of the connection terminal to the cable.

TV Rear Panel

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow you to view the camcorder tapes without using a VCR.

1. Connect a Video Cable between the AV IN 2 [VIDEO] jack on the TV and the VIDEO OUT jack on the camcorder.

Connect Audio Cables

between the AV IN 2 [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the camcorder.

Camcorder

Video Cable (Not supplied)

Audio Cable (Not supplied)

Each Camcorder has a different back panel conguration.

➣

When connecting a Camcorder, match the color of the connection terminal to the cable.

TV Side Panel

English - 12

English - 13

Connecting a VCR

HDMI IN4

Video Connection

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 9~10). Skip step 1 if you have not yet connected to an antenna or a cable system.

1. Unplug the cable or antenna from the back of the TV.

Connect the cable or

antenna to the ANT IN terminal on the back of the VCR.

Connect an RF Cable

between the ANT OUT terminal on the VCR and the ANT IN terminal on the TV.

Connect a Video Cable

between the VIDEO OUT jack on the VCR and the AV IN 1 [Y/VIDEO] or AV IN 2 [VIDEO] jack on the TV.

Connect Audio Cables

between the AUDIO OUT jacks on the VCR and the AV IN 1 (or AV IN 2) [R-AUDIO-L] jacks on the TV.

VCR Rear Panel

Audio Cable (Not supplied)

Video Cable (Not supplied)

RF Cable (Not supplied)

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

Each VCR has a different back panel conguration.

➣

When connecting a VCR, match the color of the connection terminal to the cable.

➣

When connecting to AV IN 1, the color of the AV IN 1 [Y/VIDEO] jack (Green) does not

➣

match the color of the video cable (Yellow).

If you have a “mono” (non-stereo) VCR, use a Y-connector (not supplied) to connect to

➣

the right and left audio input jacks of the TV. Alternatively, connect the cable to the “R” jack. If your VCR is stereo, you must connect two cables.

ANT IN

TV Rear Panel

TV Side Panel

S-Video Connection

Your Samsung TV can be connected to an S-Video jack on a VCR. (This connection delivers a better picture as compared to a standard VCR.)

1. To begin, follow steps 1–3 in the previous section to connect the antenna or cable to your

VCR Rear Panel

TV Rear Panel

VCR and your TV.

Connect an S-Video

Cable between the S-VIDEO OUT jack on the VCR and the [S-VIDEO] jack on the TV.

Connect Audio Cables

between the AUDIO OUT jacks on the VCR

Audio Cable (Not supplied)

S-Video Cable (Not supplied)

RF Cable (Not supplied)

and the AV IN 1 [R-AUDIO-L] jacks on the TV.

An S-Video cable may be included with a VCR. (If not, check your local electronics store.)

Each VCR has a different back panel conguration.

➣

When connecting a VCR, match the color of the connection terminal to the cable.

➣

Connecting a Digital Audio System

The rear panel jacks on your TV make it easy to connect a Digital Audio System (Home theater/Receiver) to your TV.

1. Connect an Optical Cable between the “DIGITAL AUDIO OUT (OPTICAL)” jacks on the TV and the Digital Audio Input jacks on the Digital Audio System.

When a Digital Audio System

is connected to the “DIGITAL AUDIO OUT (OPTICAL)” jack: Decrease the volume of the TV and adjust the volume level with the system’s volume control.

Digital Audio System

Optical Cable (Not supplied)

5.1CH audio is possible when the TV is connected to an external device

➣

supporting 5.1CH.

Each Digital Audio System has a different back panel conguration.

➣

When the receiver (home theater) is set to On, you can hear sound output from

➣

the TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver. If you want to hear 5.1 channel audio, connect the DIGITAL AUDIO OUT (OPTICAL) jack on

the DVD/Blu-Ray player or Cable/Satellite Box directly to an Amplier or Home

Theater, not the TV.

TV Rear Panel

ConnectinganAmplier/DVDHomeTheater

1. Connect Audio Cables between the AUDIO OUT [R-AUDIO-L] jacks on the TV and AUDIO IN [R-AUDIO-L]

jacks on the Amplier/DVD

Home Theater.

When an audio amplier is

connected to the “AUDIO OUT [R-AUDIO-L]” jacks: Decrease the volume of the TV and adjust the volume level with

the Amplier’s volume control.

Amplier/DVDHomeTheater

Audio Cable (Not supplied)

Each Amplier/DVD Home Theater has a different back panel conguration.

➣

When connecting an Amplier/DVD Home Theater, match the color of the

connection terminal to the cable.

TV Rear Panel

English - 14

English - 15

Connecting a PC

Using the D-Sub Cable

1. Connect a D-Sub Cable between PC IN [PC] connector on the TV and the PC output connector on your computer.

Connect a PC Audio Cable

between the PC IN [AUDIO] jack on the TV and the Audio Out jack of the sound card on your computer.

Using the HDMI/DVI Cable

1. Connect an HDMI/DVI cable between the HDMI IN 2 jack on the TV and the PC output jack on your computer.

Connect a 3.5 mm Stereo mini-

plug/2RCA Cable between the DVI IN(HDMI2) [R-AUDIO-L] jack on the TV and the Audio Out jack of the sound card on your computer.

TV Rear Panel

PC Audio Cable (Not supplied)

D-Sub Cable (Not supplied)

TV Rear Panel

3.5 mm Stereo mini-plug/2RCA Cable (Not supplied)

HDMI/DVI Cable (Not supplied)

Each PC has a different back panel conguration.

➣

When connecting a PC, match the color of the connection terminal to the cable.

➣

When using an HDMI/DVI cable connection, you must use the HDMI IN 2

➣

terminal.

Operation

VCR DVD STB

Turning the TV On and Off

Press the POWER button on the remote control. You can also use the POWER button on the TV.

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.

Press the POWER button on the remote control.

The message “Menu Language, Store Demo, Channels and Time will be set.” is displayed.

Press the ENTER button, then “Select Language of the OSD.” menu

is automatically displayed. Press the ENTER button.

2. Press the ▲ or ▼ button to select language, then press the ENTER button. The message “Select ‘Home Use’ when installing this TV in your home.” is displayed.

Press the ◄ or ► button to select “Store Demo” or “Home Use”, then

press the ENTER button. The message “Select the Antenna source to memorize.” is displayed.

We recommend setting the TV to “Home Use” mode for the best picture in

➣

your home environment.

“Store Demo” mode is only intended for use in retail environments.

➣

If the unit is accidentally set to “Store Demo” mode and you want to return

➣

to “Home Use” (Standard): Press the Volume button on the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.

Press the ▲ or ▼ button to memorize the channels of the selected

connection. Press the ENTER button to select “Start”.

➣

Air: “Air” antenna signal. Cable: “Cable” antenna signal. Auto: “Air” and “Cable” antenna signals.

➣

In Cable mode, you can select the correct signal source among STD,

HRC, and IRC by pressing the ▲,▼,◄ or ► button, then press the

ENTER

button. If you have Digital cable, select the cable system signal source for both Analog and Digital. Contact your local cable company to identify the type of cable system that exists in your particular area.

Menu Language, Store Demo, Channels, and Time will be set.

Select Language of the OSD.

Menu Language : English

Select ‘Home Use’ when installing this TV in your home.

Select the Antenna source to memorize.

Air

Cable

Auto

Selects the cable system.

Analog

Digital

Auto Program in Progress.

DTV Air : 02 Air : 11 DTV Cable : 23 Cable : 21

Plug & Play

Store Demo

Plug & Play

Auto Program

STD

Plug & Play

English

Español

Français

Home Use

HRC IRC

HRC IRCSTD

Start

Stop

Enter

EnterMove

Start

SkipEnterMove

Cable 38 50%

Skip

English - 16

English - 17

5. The TV will begin memorizing all of the available channels.

To stop the search before it has nished, press the ENTER button with

➣

“Stop” selected.

After all the available channels are stored, it starts to remove scrambled

channels (see page 53). And then, the Auto program menu reappears. Press the ENTER button when channel memorization is complete. The message “Set the Clock Mode.” is displayed.

Press the ENTER button.

Press the ▲ or ▼ button to select “Auto”, then Press the ENTER button. The message “Set to daylight saving time.” is displayed. If you select “Manual”, “Set current date and time” is displayed. (See page 58)

7. Press the ▲ or ▼ button to select “Off”, “On” or “Auto”, then press the

ENTER button. The message “Select the time zone in which you live.” is displayed.

Press the ▲ or ▼ button to highlight the time zone for your local area. Press

the ENTER button. If you have received a digital signal, the time will be set automatically. If not, see page 58 to set the clock.

The message “Enjoy your watching.” is displayed.

When you have nished, press the ENTER button.

Plug & Play

Removing scrambled channel.

DTV Air : 05 Air : 12 DTV Cable : 25 Cable : 32

Stop

Enter

Auto Program is completed. 119 channels are memorized. DTV Air : 05 Air : 24 DTV Cable : 10 Cable : 80

Set the Clock Mode.

Clock Mode : Auto

Set to daylight saving time.

DST : Auto

Select the time zone in which you live.

Newfoundland

Atlantic

Eastern

Central

Mountain

Pacific

Plug & Play

Auto

Manual

Plug & Play

Off

Auto



Move

Plug & Play

Enjoy your watching.

DTV Cable 41

77%

Skip

SkipEnter

SkipEnterMove

SkipEnter

If you want to reset this feature...

Press the MENU button to display the menu.

Press the ▲ or ▼ button to select “Setup”, then press the ENTER button.

2. Press the ENTER button again to select “Plug & Play”.

For further details on setting up options, refer to the pages 16~17.

The “Plug & Play” feature is only available in the TV mode.

➣

Setup

Plug & Play

Language : English

Time

Network selection : Cable

Cable Network Setup

Wireless Network Setup

V-Chip

Caption

Changing Channels

VCR DVD STB

Using the Channel Buttons

Press the CH or CH button to change channels.

When you press the CH

➣

sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels). You will not see channels that were either erased or not memorized. See page 20 to memorize channels.

To increase the channel number, turn the wheel clockwise when the

➣

Channel Display is displayed. To decrease the channel number, turn the wheel counterclockwise.

Using the Number Buttons

Press the number buttons to go directly to a channel. For example, to select

channel 27, press 2, then 7.

➣

For quick channel change, press the number buttons, then press the

ENTER

button.

Using the Button

The button is used to select stations that broadcast a digital signal.

1. For example, for Channel 7-1, press 7, then , then 1.

HD indicates the TV is receiving a Digital High Denition signal.

➣

SD indicates the TV is receiving a Standard Denition signal.

For quick channel change, press the number buttons, then press the

➣

ENTER

button.

or CH button, the TV changes channels in

Using the PRE-CH Button to select the Previous Channel

Press the PRE-CH button. The TV will switch to the last channel viewed.

➣

To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Then use the PRE-CH button to quickly alternate between them.

Adjusting the Volume

Using the Volume Button

Press the VOL – or VOL+ button to increase or decrease the volume.

➣

To turn the volume up, turn the wheel clockwise when the Volume Control window is displayed. To turn the volume down, turn the wheel counterclockwise.

Using the MUTE button

At any time, you can cut off the sound using the MUTE button.

Press MUTE button and the sound cuts off.

“ ” is displayed on the screen.

To turn mute off, press the MUTE button again or simply press the

VOL – or VOL+ button.

English - 18

English - 19

Viewing the Display

VCR DVD STB

The display identies the current channel and the status of certain audio-video

settings.

Press the INFO button on the remote control.

The TV will display the channel, the type of sound, and the status of certain

picture and sound settings.

➣

Press the INFO button once more or wait approximately 10 seconds and the display disappears automatically.

Viewing the Menus

1. With the power on, press the MENU button.

The main menu appears on the screen. The menu’s left side has icons: Picture, Sound, Channel, Setup, Input, Application.

Press the ▲ or ▼ button to select one of the icons.

Then press the ENTER button to access the icon’s sub-menu.

To move to a lower menu, turn the wheel clockwise when the menu Display

➣

is displayed. To move to a higher menu, turn the wheel counterclockwise.

TV #8

DTV Air

4-2

Picture

Sun, Sep 3 1:45 pm

Dolby Digital

Life On Venus Avenu e

♥

No Detai ld Informa tion

Mode

Backlight : 7

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Detailed Settings

1080i

9:59 am - 10:59 am

Standard

16:9

English

3. Press the EXIT button to exit.

The on-screen menus disappear from the screen after about one minute.

➣

Using the TOOLS Button

VCR DVD STB

You can use the TOOLS button to select your frequently used functions quickly and easily. The “Tools” menu changes depending on which external input mode you are viewing.

Press the TOOLS button. The “Tools” menu will appear.

Press the ▲ or ▼ button to select a menu.

3. Press the ▲/▼/◄/►/ENTER buttons to display, change, or use the selected

items. For a more detailed description of each function, refer to the corresponding page.

Anynet+ (HDMI-CEC): see page 132

• Multi-Track Sound: see page 42

• Picture Size: see page 33

• Picture Mode: see page 28

• Sound Mode: see page 40

• Sleep Timer: see page 60

• Add to Favorite: see page 48

• Switch to Cable (or Switch to Air): see page 20

• PIP: see page 39

• Auto Adjustment: see page 56

•

Multi-Track Sound : Stereo

Picture Size : 16:9

Picture Mode : Standard

Sound Mode : Custom

Sleep Timer : Off

Add to Favorite

Switch to Cable

Tools

Anynet+ (HDMI-CEC)

Move Enter e Exit

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (Air) and “Cable” channels. After the available channels are memorized, use the CH or CH button to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding or deleting channels (Channel Lists).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an Air or a Cable system).

Press the MENU button to display the menu.

Press the ▲ or ▼ button to select “Channel”, then press the ENTER button.

Channel

Antenna

Auto Program

Clear Scrambled Channel

Channel List

Fine Tune

Signal Strength

Air

Press the ENTER button to select “Antenna”.

Press the ▲ or ▼ button to select “Air” or “Cable”, then press the ENTER button.

Press the EXIT button to exit.

Easy Setting

Press the TOOLS button on the remote control.

Press the ▲ or ▼ button to select “Switch to Cable (or Switch to Air)”.

3. Press the ENTER button to switch “Cable” (or “Air”).

English - 20

Channel

Antenna

Auto Program

Clear Scrambled Channel

Channel List

Fine Tune

Signal Strength

Tools

Anynet+ (HDMI-CEC)

Multi-Track Sound : Stereo

Picture Size : 16:9

Picture Mode : Standard

Sound Mode : Custom

Sleep Timer : Off

Add to Favorite

Switch to Cable

Move Enter e Exit

Air

Cable

English - 21

Storing Channels in Memory (Automatic Method)

Press the MENU button to display the menu.

Press the ▲ or ▼ button to select “Channel”, then press the ENTER button.

Press the ▲ or ▼ button to select “Auto Program”, then press the ENTER

button.

Channel

Antenna

Auto Program

Clear Scrambled Channel

Channel List

Fine Tune

Signal Strength

Air

3. Press the ▲ or ▼ button to select the antenna connection, then press the

ENTER button.

Air: “Air” antenna signal.

➣

Cable: “Cable” antenna signal. Auto: “Air” and “Cable” antenna signals.

4. When selecting the Cable TV system:

Press the ENTER button to start the auto program.

Press the ▲,▼, ◄ or ► to select the correct analog signal cable system

source among “STD”, “HRC”, and “IRC”. Press the ▲ or ▼ button to select “Start”, then press the ENTER button. If you have Digital cable TV, select the cable system signal source for both Analog and Digital.

STD, HRC and IRC identify various types of cable TV systems. Contact

➣

your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected.

The TV begins memorizing all available stations.

➣

After all the available channels are stored, it starts to remove scrambled channels (see page 53). The Auto program menu then reappears.

➣

If you want to stop Auto Programming, press the ENTER

button.

The “Stop Auto Program?” message will be displayed. Select “Yes” by pressing the ◄ or ► button, then press the ENTER button.

Press the EXIT button to exit.

Auto Program

Select the Antenna source to memorize.

Air

Cable

Auto

Move

Auto Program

Selects the cable system.

Analog

Digital

Auto Program in Progress.

DTV Cable : 12 Cable : 32

Removing scrambled channel.

DTV Cable : 16 Cable : 45

Stop Auto Program?

DTV Cable : 16 Cable : 45

Auto Program is completed. 90 channels are memorized. DTV Cable : 10 Cable : 80

STD

Yes

HRC IRC

HRC IRCSTD

Start

Auto Program

Stop

Enter

Auto Program

DTV Cable 41

Stop

Enter

Auto Program

Move

Auto Program

Start

ReturnEnter

ReturnEnterMove

Cable 38 50%

Return

77%

Return

77%

ReturnEnter

Setting Up Your Remote Control

VCR DVD STB

SET RESET

VCR DVD STB

SET RESET

VCR DVD STB

After the television has been set up properly, your remote control can operate in different modes: TV, VCR, DVD, Set-Top Box. Pressing the corresponding button on the remote control allows you to switch between these modes and control whichever piece of equipment you choose.

The remote control might not be compatible with all DVD Players, VCRs, and Set-

➣

Top Boxes.

Setting Up the Remote to Operate Your VCR

Turn off your VCR.

2. Press the MODE button and make sure that the VCR LED is illuminated.

3. Press the SET button on your TV’s remote control.

Using the number buttons on your remote control, enter three digits of the VCR

code listed on page 24 of this manual for your brand of VCR. Make sure you enter

three digits of the code, even if the rst digit is a “0”. (If more than one code is listed, try the rst one.)

5. Press the POWER button on the remote control.

Your VCR should turn on if your remote is set up correctly.

If your VCR does not turn on after set up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of VCR. If no other codes are listed, try each VCR code, 000 through 080.

Note on Using Remote Control Modes: VCR When your remote control is in VCR mode, the volume buttons still control your TV’s volume.

Setting Up the Remote to Operate Your DVD

Turn off your DVD.

2. Press the MODE button and make sure that the DVD LED is illuminated.

3. Press the SET button on your TV’s remote control.

Using the number buttons on your remote control, enter three digits of the DVD

code listed on pages 25 of this manual for your brand of DVD.

Make sure you enter three digits of the code, even if the rst digit is a “0”. (If there is more than one code listed, try the rst one.)

5. Press the POWER button on the remote control.

Your DVD should turn on if your remote is set up correctly.

If your DVD does not turn on after set up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of DVD. If no other codes are listed, try each code, 000 through 141.

➣

Note on Using Remote Control Modes: DVD When your remote control is in DVD mode, the volume buttons still control your TV’s volume.

English - 22

English - 23

Setting Up the Remote to Operate Your STB

VCR DVD STB

SET RESET

VCR DVD STB

SET RESET

VCR DVD STB

Turn off your STB.

2. Press the MODE button and make sure that the STB LED is illuminated.

3. Press the SET button on your TV’s remote control.

Using the number buttons on your remote control, enter three digits of the STB

code listed on page 26 of this manual for your brand of STB.

Make sure you enter three digits of the code, even if the rst digit is a “0”. (If there is more than one code listed, try the rst one.)

5. Press the POWER button on the remote control.

Your STB should turn on if your remote is set up correctly.

If your STB does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of STB. (If no other codes are listed, try each code, 000 through 074.)

Note on Using Remote Control Modes: STB

➣

When your remote control is in STB mode, the volume buttons still control your TV’s volume.

Setting Up the Remote to Operate Your Cable Box

Turn off your Cable Box.

2. Press the MODE button and make sure that the STB LED is illuminated.

3. Press the SET button on your TV’s remote control.

Using the number buttons on your remote control, enter three digits of the cable

box code listed on page 26 of this manual for your brand of cable box. Make sure

you enter three digits of the code, even if the rst digit is a “0”. (If there is more than one code listed, try the rst one.)

5. Press the POWER button on the remote control.

Your cable box should turn on if your remote is set up correctly.

If your cable box does not turn on after set up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of cable box. If no other codes are listed, try each code, 000 through 046.

Note on Using Remote Control Modes: STB

➣

When your remote control is in STB mode, the volume buttons still control your TV’s volume.

Remote Control Codes

VCR

➣

Brand Code

SAMSUNG 000 001 002 003 004 005 077 078 079

ADMIRAL 020

AIWA 025

AKAI 004 027 032

AUDIO DYNAMICS 007 026

BELL&HOWELL 018

BROKSONIC 022

CANDLE 002 003 006 008 015 055

CANON 021 056

CITIZEN 002 003 006 008 015 055

COLORTYME 007

CRAIG 002 024

CURTIS MATHES 002 007 008 017 021 025 056 064 066

DAEWOO 003 010 011 012 013 014 015 016

DB 007 026

DIMENSIA 017

DYNATECH 025

ELECTROHOME 034

EMERSON

FISHER 018 024 028 029 048 051 061

FUNAI 025

GENERAL ELECTRIC

GO VIDEO 002

HARMAN KARDON 007

HITACHI 019 025 041 042 074

INSTANT REPLAY 021

JC PENNEY

JCL

JVC

KENWOOD

KLH

KONIA

LG(Goldstar)

LIOYD

LOGIK

LXI

MAGNAVOX

MARANTZ

MARTA

MEI

MEMOREX

MGA

MIDLAND

MINOLTA

MITSUBISHI

001 003 006 021 022 025 030 032 034 040 047 050 052 060 063 065 066 067 069 073

002 005 017 021 056

002 007 018 019 021 026 037 041 054 056

007 008 018 021 026 037

081 082 083

007 008 018 026 037

070

036

006 007 008 009 010

025

038

025

021 056 059

007 008 018 021 026 037 062

006

021

006 021 024 025

034

005

019 041 075

019 034 041 046

Brand Code

MONTGOMERY WARD

MTC 002 025

MULTITECH 002 005 025 038

NEC 007 008 018 026 037 062 064

OPTIMUS 020

ORION 073 074 075 076

PANASONIC 021 056 071 072

PENTAX 019 041 075

PENTEX RESEARCH+

PHILCO 021 056 059

PHILIPS 021 080

PIONEER 019 026 039 053

PORTLAND 015 049 055

PROSCAN 017

QUARTZ 018

QUASAR 021 056

RADIO SHACK/ REALISTIC

RCA

SANSUI 026

SANYO 018 024

SCOTT 003 047 052 067

SEARS 006 018 019 024 028 029 041 048 051

SHARP 020 034 045 015

SHIMTOM 027 033 038 058

SIGNATURE 025

SONY 027 033 044

SYLVANIA 021 025 056 059

SYMPHONIC 025

TANDY 018 025

TASHIKA 006

TATUNG 037

TEAC 025 037 068

TECHNICS 021

TEKNIKA 006 021 025 031

TMK 066

TOSHIBA 003 019 029 051 052

TOTEVISION 002 006

UNITECH 002

VECTOR RESEARCH

VICTOR 026

VIDEO CONCEPTS 007 026

VIDEOSONIC 002

WARDS

YAMAHA 007 008 018 026 037

ZENITH 023 027 033

020

008

006 018 020 021 024 025 029 034 048 056

002 017 019 021 035 041 043 057 068 076

007 026

002 003 006 019 020 021 024 025 034 038 041

English - 24

English - 25

SAMSUNG DVD

➣

Product Code

DVD 000 001 002 022

DVDR 003 004

BD Record 005 006

VCR COMBO 007 008 009 010 011

VCR Record 012

DHR COMBO 013

DVD

➣

Brand Code

ANAM 030

AUDIOVOX 075

AUDIOLOGIC 085

ANABA 072

APEX DIGITAL 070 071 074 086 083 084 088 111 112

AIWA 114

BROKSONIC 062

BLAUPUNKT 074

B&K 122 123

CURTIS MATHES 027

CYBER HOME 077 078 079 082

CLARION 080 125

CIRRUS 081

CYBER HOME 065

CINEVISION 095

DAEWOO 066

DENON 146

FARENHEIT 067 068

FISHER 090

GPX 060

GO VIDEO 061 089 133 135

GE 069 074

GREENHILL 074

HITACHI 064 113

HITEKER 071

HOYO 073

HARMAN / KARDON

IRT 089

INTEGRA 092

JBL 091

JVC 022 033 115 116

JATON 073

KENWOOD 051 108 109

KISS 073

KONKA 059 100 106 107

KLH 074 075

LG(Goldstar) 025 031

LOEWE 057

LASONIC 058

MOBILE AUTHORITY

MEMOREX 055

MALATA 056

MAGNAVOX 076 093

MINTEK 074 094

MONYKA 073

091 110

054

Product Code

Home Theater VCR COMBO 014 015 016

HDD Recorder COMBO 017

TWIN TRAY COMBO 018

STB DVD COMBO 019

DVD Receiver 020

AV Receiver 021

Brand Code

NORCENT 048 049 050

NEXT BASE 052

NEC 053

NANTAUS 144

NESA 074

OPTOMEDIA ELECTRONICS

OPTIVIEW 072

ONKYO 076 092 119

PHILCO 044 045

PRINCETON 046 047

PROSCAN 023

PANASONIC 024 034 124 134 136 137 138

PHILIPS 036 076

PIONEER 037 143

ROTEL 117 118

RIO 120

RCA 023 035 074 075 131 132

RAITE 073

ROWA 038

SAMPO 104

SONY 026 029 126 127 128 129 130 141

SHERWOOD 039 041

SVA 042

SYLVANIA 043 093

SHARP 140

SANSUI 062

SANYO 062 090

SHINSONIC 094

THOMSON 145

TOSHIBA 028 062 076

TECHNICS 139

TVIEW 072

TOKAI 073

TEAC 096

TECHWOOD 097

TREDEX 098 099 101

URBAN CONCEPTS

VENTURER 075

VOCOPRO 102

YAMAHA 032 063

YAMAKAWA 040 073

XWAVE 103

ZENITH 076 121

105

076

SAMSUNG SET-TOP BOX

➣

Product Code

Ground wave STB 000 001 002 008 CABLE STB 000 004 008 009 010 011 012 013 014

Satellite STB 000 003 008

SET-TOP BOX, CABLE BOX

➣

Brand Code

ALPHASTAR 023

ANAM 043

CHANNEL MASTER 018 034

CROSSDIGITAL 019

CHAPARRAL 035

DIRECT TV 015 016 017 019 022 045 060 061 062

DAEWOO 074

DISH NETWORK SYSTEM

DISHPRO 069

DRAKE 018 024 032

DX ANTENNA 027

ECHOSTAR 025 069 070 071

EXPRESSVU 069

GE 065

GENERAL INSTRUMENT

GI 116

GOI 069

HAMLIN 078 099 106

HTS 069

HOME CABLE 056

HITACHI 022 100 105

HUGHES NETWORK

IQ 020

IQ PRISM 020

JANEIL 059

JERROLD 063 113 114

JVC 069 070

LG(Goldstar) 044 073

MAGNAVOX 016 021 036 038 039 040 041 042 084

MEMOREX 016

MOTOROLA 064

MACOM 018 100 105

MITSUBISHI 015

NEXT LEVEL 047 048 064

075 076 077 078 079 080 081 082

065 066 067 068

069 070

046 047 048 063 064

015 017

098 103

013

Brand Code

OAK 101

PHILIPS 015 016 017 021 033 036 038 039 040

PIONEER 093 095 079 119

PRIMESTAR 046 049 050 063

PANASONIC 058 059 061 062 078 097 102 112 119

PAYSAT 016

PROSCAN 065 066

RCA 051 052 053 065 066 089 097 115

RADIOSHACK 064

REALISTIC 057

REGAL 078

REGENCY 090 098

SA 117 118

SAMSUNG 000 001 002 003 004 008 009 010 011

SCIENTIFIC ATLANTA

STAR TRAK 026

STS 020 027

SKY 031

SKY LIFE 005 006 007

SHACK 064

STAR CHOICE 064

SONY 054 060

SPRUCER 097

STARGATE 2000 111

SYLVANIA 091

TEXSCAN 091

TOCOM 107

TOSHIBA 015 017 028 029 030 072

ULTIMATE TV 060 066

UNIDEN 016 021 037 055 056 057

UNIVERSAL 108 109

VIEWSTAR 094 096 098 103

WAMER AMEX 121

ZENITH 024 031 068 092 104 110 112 120

041 042 067 094 096 098 103

012 013 014 075 080 078 079 081 082 076 077

117 118

English - 26

English - 27

To Select the Source

VCR DVD STB

Use to select TV or other external input sources such as DVD players or Cable Box/Satellite receivers (Set-Top Box) connected to the TV. Use to select the input source of your choice.

Press the MENU button to display the menu.

Press the ▲ or ▼ button to select “Input”, then press the ENTER button.

2. Press the ENTER button to select “Source List”. Press the ▲ or ▼ button to select signal source, then press the ENTER button.

Available signal sources: TV, AV1, AV2, S-Video, Component1,

➣

Component2, PC, HDMI1, HDMI2/DVI, HDMI3, HDMI4, USB, DLNA.

You can choose only those external devices that are connected to the TV.

➣

In the “Source List”, connected inputs will be highlighted and sorted to the top. Inputs that are not connected will be sorted to the bottom.

If each USB device is connected to 2 WISELINK jacks, each is shown as

➣

“USB1”, “USB2” in order of reading.

Using the Color buttons on the remote with the Source list

➣

Red (Refresh): Refreshes the connecting external devices.

•

TOOLS (Option)

•

Press the SOURCE button on the remote control to view an external signal

source.

: Displays the “Edit Name” and “Information” menus.

Input

AV1 ----

AV2 ----

S-Video ----

Component1 ----

Component2 ----

Refresh

Source List

Edit Name

Source List

Option

To Edit the Input Source Name

Name the device connected to the input jacks to make your input source selection easier.

Press the MENU button to display the menu.

Press the ▲ or ▼ button to select “Input”, then press the ENTER button. Press the ▲ or ▼ button to select “Edit Name”, then press the ENTER

button.

Press the ▲ or ▼ button to select “AV1”, “AV2”, “S-Video”, “Component1”,

“Component2”, “PC”, “HDMI1”, “HDMI2/DVI”, “HDMI3”, “HDMI4” input jack, then press the ENTER button.

Press the ▲ or ▼ button to select “VCR”, “DVD”, “Cable STB”,

“Satellite STB”, “PVR STB”, “AV Receiver”, “Game”, “Camcorder”, “PC”, “TV”, “IPTV”, “Blu-Ray”, “HD DVD”, “DMA” input source, then press the ENTER button. Press the EXIT button to exit.

When a PC with a resolution of 1920 x 1080@60Hz is connected to the

➣

HDMI IN 2 port, you should set the “HDMI2/DVI” mode to “PC” in the “Edit Name” of the “Input” mode.

Input

AV1 : ---- ►

AV2 : ----

S-Video : ----

Component1 : ----

Component2 : ----

PC : ----

HDMI1 : ----

AV1 : ----

AV2 : ----

S-Video : ----

Component1 : ----

Component2 : ----

PC : ----

HDMI1 : ----

Source List

Edit Name

▼

Edit Name

Enter ReturnMove

----

VCR

DVD

Cable STB

Satellite STB

PVR STB

▼

Enter ReturnMove

Picture Control

Changing the Picture Standard

You can select the type of picture which best corresponds to your viewing requirements.

Press the MENU button to display the menu.

Press the ENTER button to select “Picture”.

Picture

Mode

Backlight : 7

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Detailed Settings

Standard

2. Press the ENTER button to select “Mode”. Press the ▲ or ▼ button to select “Dynamic”, “Standard” or “Movie”. Press the ENTER button.

Dynamic: Selects the picture for high-denition in a bright room.

•

Standard: Selects the picture for the optimum display in a normal

• environment.

Movie: Selects the picture for viewing movies in a dark room.

•

3. Press the EXIT button to exit.

Easy Setting

Press the TOOLS button on the remote control.

Press the ▲ or ▼ button to select “Picture Mode”.

3. Press the ◄ or ► button to select the required option.

4. Press the EXIT or TOOLS button to exit.

Customizing the Picture Settings

Your television has several setting options that allow you to control the picture quality.

To select the desired picture mode, follow the “Changing the Picture

Standard” instructions numbers 1 and 2.

Press the ▲ or ▼ button to select “Backlight”, “Contrast”, “Brightness”,

“Sharpness”, “Color” or “Tint(G/R)”, then press the ENTER button.

3. Press the ◄ or ► button to decrease or increase the value of a particular

item. Press the ENTER button.

Press the EXIT button to exit.

➣

When you make changes to “Backlight”, “Contrast”, “Brightness”, “Sharpness”, “Color” or “Tint(G/R)”, the OSD will be adjusted accordingly.

➣

In PC mode, you can only make changes to “Backlight”, “Contrast” and “Brightness”.

➣

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

➣

The energy consumed during use can be signicantly reduced if the level

of brightness of the picture is reduced, and that this will reduce the overall running cost.

Backlight: Adjusts the brightness of LCD back light.

• Contrast: Adjusts the contrast level of the picture.

• Brightness: Adjusts the brightness level of the picture.

•

Sharpness: Adjusts the edge denition of the picture.

• Color: Adjusts color saturation of the picture.

• Tint(G/R): Adjusts the color tint of the picture.

•

Picture

Mode

Backlight : 7

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Detailed Settings

Tools

Anynet+ (HDMI-CEC)

Multi-Track Sound : Stereo

Picture Size : 16:9

Picture Mode ◄ Standard ►

Sound Mode : Custom

Sleep Timer : Off

Add to Favorite

Switch to Cable

Move

Adjust

Mode : Standard

Picture

Backlight : 7

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Detailed Settings

Picture Options

AdjustMove

Dynamic

Standard

Movie

Exit

Enter Return

►

7Backlight

English - 28

+ 125 hidden pages