SAMSUNG LN46A580P6F User Manual

Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
Comment contacter Samsung dans le monde
Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez contacter le Service Consommateurs Samsung.
Country
CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca
U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com
Customer Care Center
Samsung Electronics Canada Inc., Customer Service 55 Standish Court Mississauga, Ontario L5R 4B2 Canada
Samsung Electronique Canada Inc., Service à la Clientèle 55 Standish Court Mississauga, Ontario L5R 4B2 Canada
Samsung Electronics America, Inc. 105 Challenger Road Ridgefield Park, NJ 07660-0511
LCD TV
user manual
BN68-01392N-01
imagine the possibilities
Thank you for purchasing this Samsung product. To receive more complete service, please register your product at
www.samsung.com/global/register
Model Serial No.
Important Warranty Information Regarding Television Format Viewing
Wide screen format LCD Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format
full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to ll the screen if
your model offers this feature and the images are constantly moving. Displaying stationary graphics and images on screen, such as the dark sidebars on nonexpanded standard format television video and programming, should be limited to no more than 5% of the total television viewing per week.
Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary images that exceed the above guidelines can cause uneven aging of LCD Displays that leave subtle, but permanent burned-in ghost images in the LCD picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars.
On LCD models that offer picture sizing features, use these controls to view different formats as a full screen picture. Be careful in the selection and duration of television formats used for viewing. Uneven LCD aging as a result of format selection and use, as
well as burned-in images, are not covered by your Samsung limited warranty.
U.S.A Only
The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. In particular, this product is licensed under the following US patents: 5,991,715, 5,740,317, 4,972,484, 5,214,678, 5,323,396, 5,539,829, 5,606,618, 5,530,655, 5,777,992, 6,289,308, 5,610,985, 5,481,643, 5,544,247, 5,960,037, 6,023,490, 5,878,080, and under US Published Patent Application No. 2001-44713-A1.
This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers
the use of this product unit to encode and/or decode audio les conforming to the ISO/IEC 1
granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
Other countries
The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of
this product unit to encode and/or decode audio les conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under
this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
1172-3 or ISO/IEC 13818-3. No rights are
SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY STATEMENT
Subject to the requirements, conditions, exclusions and limitations of the original Limited Warranty supplied with Samsung Electronics (SAMSUNG) products, and the requirements, conditions, exclusions and limitations contained herein, SAMSUNG will additionally provide Warranty Repair Service in the United States on SAMSUNG products purchased in Canada, and in Canada on SAMSUNG products
purchased in the United States, for the warranty period originally specied, and to the Original Purchaser only.
The above described warranty repairs must be performed by a SAMSUNG Authorized Service Center. Along with this Statement, the Original Limited Warranty Statement and a dated Bill of Sale as Proof of Purchase must be presented to the Service Center. Transportation to and from the Service Center is the responsibility of the purchaser.
Conditions covered are limited only to manufacturing defects in material or workmanship, and only those encountered in normal use of the product.
Excluded, but not limited to, are any originally specied provisions for, in-home or on-s
exchanges or replacements, accessories, options, upgrades, or consumables.
For the location of a SAMSUNG Authorized Service Center, please call toll-free:
In the United States : 1-800-SAMSUNG (1-800-726-7864) In Canada : 1-800-SAMSUNG
See the warranty card for more information on warranty terms.
Precautions When Displaying a Still Image
A still image may cause permanent damage to the TV screen
Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention. This image
• retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the left,
right and center of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause a similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.
ite services, minimum or maximum repair times,
© 2008 Samsung Electronics Co., Ltd. All rights reserved.
Contents
English
General Information
List of Features ..................................................................2
Accessories .......................................................................2
Viewing the Control Panel .................................................3
Viewing the Connection Panel ...........................................4
Remote Control .................................................................5
Installing Batteries in the Remote Control .........................6
Connections
Connecting VHF and UHF Antennas .................................6
Connecting Cable TV ........................................................7
Connecting a DVD Player or Cable Box/Satellite receiver
(Set-Top Box) via HDMI .....................................................8
Connecting a DVD Player or Cable Box/Satellite receiver
(Set-Top Box) via DVI ........................................................8
Connecting a DVD Player or Cable Box/Satellite receiver
(Set-Top Box) via Component cables ................................9
Connecting a Camcorder ...................................................9
Connecting a VCR ...........................................................10
Connecting a Digital Audio System .................................11
Connecting an Amplier/DVD Home Theater .................. 11
Connecting a PC .............................................................11
Operation
Turning the TV On and Off ..............................................12
Plug & Play Feature .........................................................12
Changing Channels .........................................................13
Adjusting the Volume .......................................................14
Viewing the Display .........................................................14
Viewing the Menus ..........................................................14
Using the TOOLS Button .................................................15
Memorizing the Channels ................................................15
To Select the Source .......................................................17
To Edit the Input Source Name ........................................17
Picture Control
Changing the Picture Standard .......................................18
Customizing the Picture Settings .....................................18
Adjusting the Detailed Settings ........................................19
Resetting the Picture Settings to the Factory Defaults ....22
Conguring Picture Options .............................................23
Viewing Picture-in-Picture ...............................................27
Sound Control
Changing the Sound Standard ........................................29
Customizing the Sound ...................................................29
Setting the TruSurround XT .............................................30
Choosing Preferred Language ........................................31
Choosing a Multi-Channel Sound (MTS) track ................31
Automatic Volume Control ...............................................32
Setting the TV Speakers On/Off ......................................32
Listening to the Sound of the Sub (PIP) Picture ..............33
Resetting the Sound Settings to the Factory Defaults .....33
Connecting Headphones (Sold separately) .....................33
PC Display
Using Your TV as a Computer (PC) Display ....................42
Display Modes .................................................................42
Setting up the TV with your PC .......................................43
Time Setting
Setting the Clock .............................................................45
Function Description
Selecting a Menu Language ............................................49
Using the V-Chip ..............................................................49
Viewing Closed Captions (On-Screen Text Messages)
- Analog ...........................................................................56
Viewing Closed Captions (On-Screen Text Messages)
- Digital ............................................................................57
Adjusting the TV On/Off Melody Sound ...........................58
Setting the Entertainment mode ......................................58
Using the Energy Saving Feature ....................................59
Upgrading the Software ...................................................60
WISELINK
Using the WISELINK Function ........................................61
Using the Photo List ........................................................62
Sorting Photo List ............................................................64
Viewing a Photo or Slide Show ......................................68
Using the Music List
Sorting Music List ............................................................73
Playing a Music File .........................................................77
Using the Setup Menu .....................................................79
About Anynet
What is Anynet+?.............................................................80
Connecting Anynet+ Devices...........................................80
Setting Up Anynet+ .........................................................81
Scanning and Switching between Anynet+ Devices ........81
Recording ........................................................................82
Listening through a Receiver (Home theater) ..................83
Troubleshooting for Anynet+ ...........................................83
........................................................72
+
Appendix
Troubleshooting ...............................................................84
Installing the Stand ..........................................................86
Disconnecting the Stand ..................................................86
Auto Wall-Mount Adjustment (Sold separately) ..............87
Wall Mount Kit Specications (VESA) .............................88
Using the Anti-Theft Kensington Lock .............................89
Specications ..................................................................90
Dimensions ......................................................................91
Channel Control
Managing Channels .........................................................34
Clearing Scrambled Channels - Digital ............................40
Fine Tuning Analog Channels ..........................................40
Checking the Digital-Signal Strength ...............................41
Symbol Press Note One-Touch Button
English - 1

General Information

List of Features

Adjustable picture settings that can be stored in the TV’s memory.
• Automatic timer to turn the TV on and off.
• A special sleep timer.
• Excellent Digital Interface & Networking :
• With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Cable Box/Satellite receiver (Set-Top Box) needed.
You can listen to music les and view pictures on USB Mass Storage Class (MSC) devices.
HDMI/DVI connection of your PC to this TV.
• Excellent Picture Quality
- DNIe technology provides life-like clear images. SRS TruSurround XT
- SRS TruSurround XT provides a virtual surround system.

Accessories

Please make sure the following items are included with your LCD TV. If any items are missing, contact your dealer.
Remote Control & Batteries (AAA x 2)
(BN59-00673A)
Warranty Card / Registration Card /
Safety Guide Manual
(Not available in all locations)
The items color and shape may vary depending on the model.
Ferrite Core (Power Cord)
The ferrite cores are used to shield the cables from interference. When connecting a cable, open the ferrite core and clip it around the cable near the plug.
Power Cord
(3903-000144)
Cleaning Cloth
(BN63-01798A)
(LN46A580P6F: BN63-04353A) (LN52A580P6F: BN63-04353A)
Owner’s Instructions
Cover-Bottom
Ferrite Core
(3301-001110)
English - 2
English - 3

Viewing the Control Panel

77
1 2
3
4
6
5
8
Buttons on the Lower-Right Part of the Panel
The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu.
To use the more advanced features, you must use the remote control.
Front Panel buttons
Touch each button to operate.
The product color and shape may vary depending on the model.
1
SOURCE
Toggles between all the available input sources (TV, AV1, AV2, S-Video, Component1, Component2, PC, HDMI1, HDMI2/DVI, HDMI3, USB). In the on­screen menu, use this button as you would use the ENTER button on the remote control.
2
MENU
Press to see an on-screen menu of your TV’s features.
3
– VOL +
Press to increase or decrease the volume. In the on-screen menu, use the – VOL + buttons as you
would use the ◄ and ► buttons on the remote control.
4
CH
Press to change channels. In the on-screen menu, use the CH buttons as
you would use the ▼ and ▲ buttons on the remote
control.
5
POWER INDICATOR
Blinks and turns off when the power is on and lights up in stand-by mode.
6
(Power)
Press to turn the TV on and off.
7
SPEAKERS
8
REMOTE CONTROL SENSOR
Aim the remote control towards this spot on the TV.

Viewing the Connection Panel

Use the connection panel jacks to connect A/V components that will be connected continuously, such as DVD players or a VCR. For more information on connecting equipment, see pages 6~11.
[TV Side Panel][TV Rear Panel]
The product color and shape may vary depending on the model.
AUDIO OUT
1
Connects to the audio input jacks on your Amplier/ Home theater.
2
DIGITAL AUDIO OUT (OPTICAL)
Connects to a Digital Audio component.
3
PC IN [PC] / [AUDIO]
Connects to the video and audio output jacks on your PC.
4
HDMI IN 1, 2, 3 / DVI IN(HDMI2)[R-AUDIO-L]
Connects to the HDMI jack of a device with an HDMI output.
- No sound connection is needed for an HDMI to HDMI connection.
Use the HDMI IN 2 jack for DVI connection to an external device. Use a DVI to HDMI cable or DVI-HDMI adapter (DVI to HDMI) for video connection and the DVI IN (HDMI2) [R-AUDIO-L] jacks for audio.
- When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.
5
ANT IN
Connects to an antenna or cable TV system.
6
WISELINK
Connect a USB mass storage device to view photo les and play audio les.
7
AV IN 2
Video and audio inputs for external devices, such as a camcorder or VCR.
S-VIDEO Connects an S-Video signal from a camcorder or VCR.
8
(HEADPHONE)
Connects a set of external headphones for private listening.
9
POWER INPUT
Connects the supplied power cord.
0
COMPONENT IN 1, 2 / AV IN 1
Connects Component video/audio. The COMPONENT IN 1 jack is also used as the
AV IN 1 jack.
- Connect the video cable to the COMPONENT IN 1 [Y/VIDEO] jack and the audio cable to the COMPONENT IN 1 [R-AUDIO-L] jacks.
!
EX-LINK
Connect this to the jack on the optional wall mount bracket. This will allow you to adjust the TV viewing angle using your remote control.
@
KENSINGTON LOCK
The Kensington Lock (optional) is a device used to
physically x the system when used in a public place.
If you want to use a locking device, contact the dealer where you purchased the TV.
The location of the Kensington Lock may be different
depending on its model.
English - 4
English - 5

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.
1
POWER
Turns the TV on and off.
2
TV
Selects the TV mode directly.
3
NUMERIC BUTTONS
Press to change the channel.
4
Press to select additional channels (digital and analog) being broadcast by the same station. For example, to select channel “54-3”, press “54”, then press “ ” and “3”.
5
(MUTE)
Press to temporarily cut off the sound.
6
VOL – / VOL +
Press to increase or decrease the volume.
7
CH LIST
Used to display Channel Lists on the screen.
8
TOOLS
Use to quickly select frequently used functions.
9
INFO
Press to display information on the TV screen.
0
COLOR BUTTONS
Use these buttons in the Channel list, WISELINK, etc.
!
CC
Controls the caption decoder.
@
E.MODE
Press to select the preset display and sound modes for sports, cinema and games.
#
Use these buttons in the
DMA, WISELINK and Anynet+ modes. ( : This remote can be used to control recording on Samsung recorders with the Anynet+ feature)
$
ON/OFF
Press to backlight the buttons on the remote. This function is convenient for using at night or when the room is dark. (Using the remote control with the ON/OFF to On will reduce the battery usage time.)
light button set
%
PRE-CH
Tunes to the previous channel.
^
CH / CH
Press to change channels.
&
SOURCE
Press to display and select the available video sources.
*
W.LINK (WISELINK)
This function enables you to view and play photo and music
les from an external device.
(Refer to pages 62 (Photo) and 72 (Music))
(
MENU
Displays the main on-screen menu.
)
RETURN
Returns to the previous menu.
a
 UP▲/DOWN▼/LEFT◄/
RIGHT►/ENTER
Use to select on-screen menu items and change menu values.
b
EXIT
Press to exit the menu.
c
DMA (Digital Media Adapter)
Use this when connecting a SAMSUNG DMA device through an HDMI interface and switching to DMA mode.
For more information on the operating procedures, refer to the user manual of the DMA.
This button is available when “Anynet+(HDMI-CEC)” is “On”. (see page 81)
d
MTS
Press to choose stereo, mono or Separate Audio Program (SAP broadcast).
e
FAV.CH
Press to switch to your favorite channels.
f
P.SIZE
Picture size selection.
The performance of the remote control may be affected by bright light.

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the gure.
2. Install two AAA size batteries.
Make sure to match the “+” and “–” ends of the batteries with the diagram inside the
compartment.
3.
Replace the cover.
Remove the batteries and store them in a cool, dry place if you won’t be using the
remote control for a long time.
The remote control can be used up to about 23 feet from the TV. (Assuming typical TV usage, the batteries should last for about one year.)
Using the remote control with the ON/OFF light button set to On will reduce the
battery usage time.
If the remote control doesn’t work, check the following:
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power outage or is the power cord unplugged?
5. Is there a special uorescent light or neon sign nearby?

Connections

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like the diagram to the right, see “Antennas
with 300 Ω Flat Twin Leads” below.
If your antenna has one lead that looks like the diagram to the right, see “Antennas with
75 Ω Round Leads”.
If you have two antennas, see “Separate VHF and UHF Antennas”.
Antennaswith300ΩFlatTwinLeads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300
Ω twin at leads, follow the directions below.
1.
Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not
supplied). Use a screwdriver to tighten the screws.
ANT IN
Plug the adaptor into the ANT IN terminal on the back of the TV.
2.
Antennaswith75ΩRoundLeads
1. Plug the antenna lead into the ANT IN terminal on the back of the TV.
ANT IN
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).
1.
Connect both antenna leads to the combiner.
UHF
VHF
2. Plug the combiner into the ANT IN terminal on the bottom of the rear panel.
English - 6
ANT IN
UHF
VHF
English - 7

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.
Cable without a Cable Box
Plug the incoming cable into the ANT IN terminal on the back of the TV.
1.
Because this TV is cable-ready, you do not need a cable box to view
unscrambled cable channels.
Connecting to a Cable Box that Descrambles All Channels
1.
Find the cable that is connected to the ANT OUT terminal on your cable box.
This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.
2.
Connect the other end of this cable to the ANT IN terminal on the back of the TV.
ANT IN
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch and four lengths of RF cable. (These items are available at most electronics stores.)
1.
Find and disconnect the cable that is
connected to the ANT IN terminal on your cable box.
This terminal might be labeled
ANT IN
“ANT IN”, “VHF IN” or simply, “IN”.
ANT IN
ANT OUT
ANT IN
2. Connect this cable to a two-way splitter.
Connect an RF cable between the
3.
Incoming
cable
Splitter
OUTPUT terminal on the splitter and the IN terminal on the cable box.
Incoming
cable
Splitter
Cable Box
4. Connect an RF cable between the ANT OUT terminal on the cable box and the B–IN terminal on the RF(A/B) switch.
Connect another cable between the
5.
Incoming
cable
Splitter
Cable Box
RF (A/B)
Switch
other OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch.
6. Connect the last RF cable between
Incoming
cable
Splitter
Cable Box
RF (A/B)
Switch
ANT IN
the OUT terminal on the RF (A/B) switch and the ANT IN terminal on the rear of the TV.
Incoming
cable
Splitter
Cable Box
RF (A/B)
Switch
TV Rear
After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.
1. Connect an HDMI Cable between the HDMI IN (1, 2 or 3) jack on the TV and the HDMI jack on the DVD Player or Cable Box/Satellite receiver (Set-Top Box).
DVD Player or Cable Box/Satellite receiver
(Set-Top Box) Rear Panel
TV Rear Panel
TV Side Panel
What is HDMI?
HDMI Cable (Not supplied)
or
• HDMI(High-Denition Multimedia Interface), is an interface that enables the
transmission of digital audio and video signals using a single cable.
• The difference between HDMI and DVI is that the HDMI device is smaller in size and has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed.
Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different back
panel conguration.
The TV may not output sound and pictures may be displayed with abnormal color when
DVD players/Cable Boxes/Satellite receivers supporting HDMI versions older than 1.3 are connected. When connecting an older HDMI cable and there is no sound, connect the HDMI cable to the HDMI IN 2 jack and the audio cables to the DVI IN (HDMI2) [R-AUDIO-L] jacks on the back of the TV. If this happens, contact the company that
provided the DVD player/Cable Box/Satellite receiver to conrm the HDMI version, then
request an upgrade.
HDMI cables that are not 1.3 may cause annoying icker or no screen display
.

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via DVI

This connection can only be made if there is a DVI Output connector on the external device.
1. Connect a DVI to HDMI Cable or DVI-HDMI Adapter between the HDMI IN 2 jack on the TV and the DVI jack on the DVD Player or Cable Box/Satellite receiver (Set-Top Box).
DVD Player or Cable Box/
Satellite receiver (Set-Top Box)
TV Rear Panel
Connect Audio Cables
2.
between the DVI IN (HDMI 2) [R-AUDIO-L] jack on the TV and the DVD Player or Cable Box/Satellite receiver (Set-Top Box).
Audio Cable (Not supplied)
2
DVI to HDMI Cable (Not supplied)
1
Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different back
panel conguration.
When connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box), match
the color of the connection terminal to the cable.
When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.
English - 8
English - 9

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via Component cables

The rear panel jacks on your TV make it easy to connect a DVD Player or Cable Box/Satellite receiver (Set-Top Box) to your TV.
1. Connect a Component Cable between the COMPONENT IN (1 or 2) [Y, PB, PR] jacks on the TV and the COMPONENT [Y, PB, PR] jacks on the DVD Player or Cable Box/Satellite receiver (Set-Top Box).
2.
Connect Audio
Cables between the COMPONENT IN(1 or
2) [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the DVD Player or Cable Box/Satellite receiver (Set-Top Box).
DVD Player or Cable Box /
Satellite receiver (Set-Top Box)
Audio Cable
2
(Not supplied)
Component Cable (Not supplied)
1
Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and
Pr (Red) for enhanced video quality. Be sure to match the component video and audio connections. For example, if connecting a Component video cable to COMPONENT IN 1, connect the audio cable to COMPONENT IN 1 also.
Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different back
panel conguration.
When connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box), match
the color of the connection terminal to the cable.
TV Rear Panel

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow you to view the camcorder tapes without using a VCR.
1. Connect a Video Cable (or S-Video Cable) between the AV IN 2 [VIDEO] (or S-VIDEO) jack on the TV and the VIDEO OUT jack on the camcorder.
2.
Connect Audio Cables
between the AV IN 2 [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the camcorder.
Camcorder
Each Camcorder has a different back panel conguration.
When connecting a Camcorder, match the color of the connection terminal to the cable.
or
S-Video Cable (Not supplied)
1
Video Cable (Not supplied)
1
Audio Cable
2
(Not supplied)
TV Side Panel

Connecting a VCR

Video Connection
These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 6~7). Skip step 1 if you have not yet connected to an antenna or a cable system.
1. Unplug the cable or antenna from the back of the TV.
2.
Connect the cable or
antenna to the ANT IN terminal on the back of the VCR.
3.
Connect an RF Cable
between the ANT OUT terminal on the VCR and the ANT IN terminal on the TV.
4.
Connect a Video Cable
VCR Rear Panel
between the VIDEO OUT jack on the VCR and the AV IN 1 [Y/VIDEO] or AV IN 2 [VIDEO] jack on the TV.
5.
Connect Audio Cables
between the AUDIO OUT jacks on the VCR and the AV IN 1 (or AV IN 2) [R-AUDIO-L] jacks
Audio Cable (Not supplied)
5
Video Cable (Not supplied)
4
RF Cable (Not supplied)
3
on the TV.
If you have a “mono”
(non-stereo) VCR, use a Y-connector (not supplied) to connect to the right and left audio input jacks of the
Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.
Each VCR has a different back panel conguration.
When connecting a VCR, match the color of the connection terminal to the cable.
When connecting to AV IN 1, the color of the AV IN 1 [Y/VIDEO] jack (Green) does not
match the color of the video cable (Yellow).
TV. Alternatively, connect the cable to the “R” jack. If your VCR is stereo, you must connect two cables.
S-Video Connection
Your Samsung TV can be connected to an S-Video jack on a VCR. (This connection delivers a better picture as compared to a standard VCR.)
1. To begin, follow steps 1–3 in the previous section to connect the antenna or cable to your
VCR Rear Panel
VCR and your TV.
2.
Connect an S-Video
Cable between the S-VIDEO OUT jack on the VCR and the AV IN 2 [S-VIDEO] jack on the TV.
3.
Connect Audio Cables
between the AUDIO OUT jacks on the VCR
RF Cable (Not supplied)
1
S-Video Cable (Not supplied)
2
Audio Cable (Not supplied)
3
and the AV IN 2 [R-AUDIO-L] jacks on the TV.
An S-Video cable may be included with a VCR. (If not, check your local electronics store.)
Each VCR has a different back panel conguration.
When connecting a VCR, match the color of the connection terminal to the cable.
ANT IN
TV Rear Panel
TV Rear Panel
TV Side Panel
TV Side Panel
English - 10
English - 11

Connecting a Digital Audio System

The rear panel jacks on your TV make it easy to connect a Digital Audio System (Home theater/Receiver) to your TV.
1. Connect an Optical Cable between the “DIGITAL AUDIO
Digital Audio System
TV Rear Panel
OUT (OPTICAL)” jacks on the TV and the Digital Audio Input jacks on the Digital Audio System.
When a Digital Audio System
is connected to the “DIGITAL AUDIO OUT (OPTICAL)” jack: Decrease the volume of the
Optical Cable (Not supplied)
TV and adjust the volume level with the system’s volume control.
5.1CH audio is possible when the TV is connected to an external device
supporting 5.1CH.
Each Digital Audio System has a different back panel conguration.
➣ ➣
When the receiver (home theater) is set to On, you can hear sound output from the TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver. If you want to hear 5.1 channel audio, connect the DIGITAL AUDIO OUT (OPTICAL) jack on the DVD player or
Cable/Satellite Box directly to an Amplier or Home Theater, not the TV.
ConnectinganAmplier/DVDHomeTheater
1. Connect Audio Cables between the AUDIO OUT [R-AUDIO-L] jacks on the TV and AUDIO IN [R-AUDIO-L]
jacks on the Amplier/DVD
Home Theater.
When an audio amplier is
connected to the “AUDIO OUT [R-AUDIO-L]” jacks: Decrease the volume of the TV and adjust the volume level with
the Amplier’s volume control.

Connecting a PC

Using the D-Sub Cable
1.
Connect a D-Sub Cable
between PC IN [PC] connector on the TV and the PC output connector on your computer.
2.
Connect a PC Audio Cable
between the PC IN [AUDIO] jack on the TV and the Audio Out jack of the sound card on your computer.
Using the HDMI/DVI Cable
1.
Connect an HDMI/DVI cable
between the HDMI IN 2 jack on the TV and the PC output jack on your computer.
2.
Connect a 3.5 mm Stereo mini-
plug/2RCA Cable between the DVI IN(HDMI2) [R-AUDIO-L] jack on the TV and the Audio Out jack of the sound card on your computer.
TV Rear Panel
Amplier/DVDHomeTheater
Audio Cable (Not supplied)
Each Amplier/DVD Home Theater has a different back panel conguration.
➣ ➣
When connecting an Amplier/DVD Home Theater, match the color of the
connection terminal to the cable.
Using the D-Sub Cable
PC Audio Cable (Not supplied)
2
D-Sub Cable (Not supplied)
1
Using the HDMI/DVI Cable
3.5 mm Stereo mini-plug/2RCA Cable (Not supplied)
2
HDMI/DVI Cable (Not supplied)
1
Each PC has a different back panel conguration.
➣ ➣
When connecting a PC, match the color of the connection terminal to the cable.
When using an HDMI/DVI cable connection, you must use the HDMI IN 2 terminal.
TV Rear Panel
TV Rear Panel

Operation

Turning the TV On and Off

Press the POWER button on the remote control. You can also use the POWER button on the TV.

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.
1.
Press the POWER button on the remote control.
The message “Menu Language, Store Demo, Channels, and Time will be set.” is displayed.
Press the ENTER button, then “Select language of the OSD.” menu
is automatically displayed. Press the ENTER button.
2. Press the ▲ or ▼ button to select language, then press the ENTER button. The message “Select ‘Home Use’ when installing this TV in your home.” is displayed.
Press the ◄ or ► button to select “Store Demo” or “Home Use”, then
3.
press the ENTER button. The message “Select the Antenna source to memorize.” is displayed.
We recommend setting the TV to “Home Use” mode for the best picture in
your home environment.
“Store Demo” mode is only intended for use in retail environments.
If the unit is accidentally set to “Store Demo” mode and you want to return
to “Home Use” (Standard): Press the Volume button on the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.
4.
Press the ▲ or ▼ button to memorize the channels of the selected
connection. Press the ENTER button to select “Start”.
Air: “Air” antenna signal. Cable: “Cable” antenna signal. Auto: “Air” and “Cable” antenna signals.
In Cable mode, you can select the correct signal source among STD,
HRC, and IRC by pressing the ▲, ▼, ◄ or ► button, then press the
ENTER signal source for both Analog and Digital. Contact your local cable company to identify the type of cable system that exists in your particular area.
The TV will begin memorizing all of the available channels.
5.
To stop the search before it has nished, press the ENTER button with “Stop” selected.
After all the available channels are stored, it starts to remove scrambled
channels (see page 40). And then, the Auto program menu reappears. Press the ENTER button when channel memorization is complete. The message “Set the Clock Mode.” is displayed.
button. If you have Digital cable, select the cable system
English - 12
Plug & Play
Menu Language, Store Demo, Channels, and Time will be set.
OK
Select language of the OSD.
Menu Language : English
Select ‘Home Use’ when installing this TV in your home.
Select the Antenna source to memorize.
Air
Cable
Auto
Selects the cable system.
Analog
Digital
Auto Program in Progress.
DTV Air : 02 Air : 11 DTV Cable : 23 Cable : 21
Removing scrambled channel.
DTV Air : 05 Air : 12 DTV Cable : 25 Cable : 32
Auto Program is completed. 119 channels are memorized. DTV Air : 05 Air : 24 DTV Cable : 10 Cable : 80
Plug & Play
Plug & Play
Store Demo
Plug & Play
Plug & Play
STD
Plug & Play
Plug & Play
Plug & Play
English
Español
Français
Home Use
HRC IRC
HRC IRCSTD
Start
Stop
Stop
OK
Enter
DTV Cable 41
Enter
EnterMove
Start
Start
Start
Cable 38 50%
77%
ReturnEnter
EnterMove
SkipEnterMove
SkipEnterMove
Skip
Skip
SkipEnter
English - 13
6. Press the ENTER button.
Press the ▲ or ▼ button to select “Auto”, then Press the ENTER button. The message “Set to daylight saving time.” is displayed. If you select “Manual”, “Set current date and time” is displayed. (See page 45)
Press the ▲ or ▼ button to select “Off” or “On”, then press the ENTER
7.
button. The message “Select the time zone in which you live.” is displayed.
Press the ▲ or ▼ button to highlight the time zone for your local area.
8.
Press the ENTER button. If you have received a digital signal, the time will be set automatically. If not, see page 45 to set the clock.
9.
The message “Enjoy your watching.” is displayed.
When you have nished, press the ENTER button.
Plug & Play
Set the Clock Mode.
Clock Mode : Auto
Set to daylight saving time.
DST : Auto
Select the time zone in which you live.
Newfoundland
Atlantic
Eastern
Central
Mountain
Pacific
Auto
Manual
Plug & Play
Off
On
Plug & Play
Move
Plug & Play
Enjoy your watching.
OK
SkipEnterMove
SkipEnterMove
SkipEnter
If you want to reset this feature...
1.
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select “Setup”, then press the ENTER button.
2. Press the ENTER button again to select “Plug & Play”. For further details on setting up options, refer to the pages 12~13.
The “Plug & Play” feature is only available in the TV mode.

Changing Channels

Using the Channel Buttons
Press the CH or CH button to change channels.
1.
When you press the CH
sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels). You will not see channels that were either erased or not memorized. See page 16 to memorize channels.
Using the Number Buttons
Press the number buttons to go directly to a channel. For example, to select
1.
channel 27, press 2, then 7.
For quick channel change, press the number buttons, then press the
ENTER
button.
or CH button, the TV changes channels in
Setup
Plug&Play
Language : English
Time
V-Chip
Caption
External Settings
Entertainment : Off
Energy Saving : Off
Using the Button
The button is used to select stations that broadcast a digital signal.
1. For example, for Channel 7-1, press 7, then , then 1.
HD indicates the TV is receiving a Digital High Denition signal.
SD indicates the TV is receiving a Standard Denition signal.
For quick channel change, press the number buttons, then press the
ENTER
button.
Using the PRE-CH Button to select the Previous Channel
Press the PRE-CH button. The TV will switch to the last channel viewed.
1.
To quickly switch between two channels that are far apart, tune to one
channel, then use the number button to select the second channel. Then use the PRE-CH button to quickly alternate between them.

Adjusting the Volume

Using the Volume Button
Press the VOL – or VOL + button to increase or decrease the volume.
1.
Using the MUTE button
At any time, you can cut off the sound using the MUTE button.
1.
Press MUTE button and the sound cuts off.
“ ” is displayed on the screen.
2.
To turn mute off, press the MUTE button again or simply press the
VOL – or VOL + button.

Viewing the Display

The display identies the current channel and the status of certain audio-video
settings.
1.
Press the INFO button on the remote control.
The TV will display the channel, the type of sound, and the status of certain
picture and sound settings.
Press the INFO button once more or wait approximately 10 seconds and
the display disappears automatically.

Viewing the Menus

1. With the power on, press the MENU button. The main menu appears on the screen. The menu’s left side has icons: Picture, Sound, Channel, Setup, Input, Application.
2.
Press the ▲ or ▼ button to select one of the icons.
Then press the ENTER button to access the icon’s sub-menu.
3. Press the EXIT button to exit.
The on-screen menus disappear from the screen after about one minute.
TV #8
DTV Air
4-2
Picture
Sun, Sep 3 1:45 pm
Dolby Digital
Life On Venus Avenu e
No Detai ld Informa tion
Mode
Backlight : 7
Contrast : 95
Brightness : 45
Sharpness : 50
Color : 50
Tint (G/R) : G50/R50
Detailed Settings
:
1080i
9:59 am - 10:59 am
Standard
|
|
16:9
English
English - 14
English - 15

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and easily. The “TOOLS” menu changes depending on which external input mode you are viewing.
1.
Press the TOOLS button.
The “TOOLS” menu will appear.
2.
Press the ▲ or ▼ button to select a menu.
3. Press the ▲/▼/◄/►/ENTER buttons to display, change, or use the selected items. For a more detailed description of each function, refer to the corresponding page.
Device List
TOOLS
EnterMove
e
Exit
Device List: see page 81
• Picture Mode: see page 18
• Sound Mode: see page 29
• Sleep Timer: see page 47
• Add to Favorite: see page 36
• Switch to Cable (or Switch to Air): see page 15
• PIP: see pages 27~28
• Auto adjustment: see page 43
Picture Mode : Standard
Sound Mode : Custom
Sleep Timer : Off
Add to Favorite
Switch to Cable

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (Air) and “Cable” channels. After the available channels are memorized, use the CH or CH button to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding or deleting channels (Channel Lists).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an Air or a Cable system).
Press the MENU button to display the menu.
1.
Press the ▲ or ▼ button to select “Channel”, then press the ENTER button.
Channel
Antenna
:
Auto Program
Clear Scrambled Channel
Channel List
Fine Tune
Signal Strength
Air
2.
Press the ENTER button to select “Antenna”.
Press the ▲ or ▼ button to select “Air” or “Cable”, then press the ENTER button.
Press the EXIT button to exit.
Easy Setting
1.
Press the TOOLS button on the remote control.
2.
Press the ▲ or ▼ button to select “Switch to Cable (or Switch to Air)”.
3. Press the ENTER button to switch “Cable” (or “Air”).
Channel
Antenna
:
Auto Program
Clear Scrambled Channel
Channel List
Fine Tune
Signal Strength
Device List
Picture Mode : Standard
Sound Mode : Custom
Sleep Timer : Off
Add to Favorite
Switch to Cable
Air
Air
Cable
TOOLS
Move Enter e Exit
Storing Channels in Memory (Automatic Method)
Press the MENU button to display the menu.
1.
Press the ▲ or ▼ button to select “Channel”, then press the ENTER button.
2.
Press the ▲ or ▼ button to select “Auto Program”, then press the ENTER
button.
Antenna
Channel
Auto Program
Clear Scrambled Channel
Channel List
Fine Tune
Signal Strength
:
Air
3. Press the ▲ or ▼ button to select the antenna connection, then press the
ENTER button.
Air: “Air” antenna signal.
Cable: “Cable” antenna signal. Auto: “Air” and “Cable” antenna signals.
When selecting the Cable TV system:
4.
Press the ENTER button to start the auto program.
Press the ▲,▼, ◄ or ► to select the correct analog signal cable system source among “STD”, “HRC”, and “IRC”. Press the ▲ or ▼ button to select
“Start”, then press the ENTER button. If you have Digital cable TV, select the cable system signal source for both Analog and Digital.
STD, HRC and IRC identify various types of cable TV systems. Contact
your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected.
5.
The TV begins memorizing all available stations.
After all the available channels are stored, it starts to remove scrambled channels (see page 40). The Auto program menu then reappears.
If you want to stop Auto Programming, press the ENTER
button.
The “Stop Auto Program?” message will be displayed. Select “Yes” by pressing the ◄ or ► button, then press the ENTER button.
Press the EXIT button to exit.
Auto Program
Select the Antenna source to memorize.
Air
Cable
Auto
Move
Auto Program
Selects the cable system.
Analog
Digital
Auto Program in Progress.
DTV Cable : 12 Cable : 32
Removing scrambled channel.
DTV Cable : 16 Cable : 45
Stop Auto Program?
DTV Cable : 16 Cable : 45
Auto Program is completed. 3 channels are memorized.
DTV Cable : 1 Cable : 2
STD
STD
Yes
HRC IRC
HRC IRC
Start
Move
Auto Program
Stop
Enter
Auto Program
DTV Cable 41
Stop
Enter
Auto Program
No
Move
Auto Program
Start
Start
Start
ReturnEnter
ReturnEnter
Cable 38 50%
Return
77%
Return
77%
ReturnEnter
English - 16
OK
ReturnEnter
English - 17

To Select the Source

Use to select TV or other external input sources such as DVD players or Cable Box/Satellite receivers (Set-Top Box) connected to the TV. Use to select the input source of your choice.
1.
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select “Input”, then press the ENTER button.
2. Press the ENTER button to select “Source List”. Press the ▲ or ▼ button to select signal source, then press the ENTER button.
Available signal sources: TV, AV1, AV2, S-Video, Component1,
Component2, PC, HDMI1, HDMI2/DVI, HDMI3, USB.
You can choose only those external devices that are connected to the TV.
In the “Source List”, connected inputs will be highlighted and sorted to the top. Inputs that are not connected will be sorted to the bottom.
Using the Color buttons on the remote with the Source list
Red (Refresh): Refreshes the connecting external devices.
TOOLS (Option)
Press the SOURCE button on the remote control to view an external signal
O
source.
: Displays the “Edit Name” and “Information” menus.
Input
Source List
Edit Name
TV
AV1 ----
AV2 ----
S-Video ----
Component1 ----
Component2 ----
PC ----
Refresh
TOOLS
Option

To Edit the Input Source Name

Name the device connected to the input jacks to make your input source selection easier.
1.
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select “Input”, then press the ENTER button. Press the ▲ or ▼ button to select “Edit Name”, then press the ENTER
button.
Press the ▲ or ▼ button to select “AV1”, “AV2”, “S-Video”, “Component1”,
2.
“Component2”, “PC”, “HDMI1”, “HDMI2/DVI”, “HDMI3” input jack, then press the ENTER button.
Press the ▲ or ▼ button to select “VCR”, “DVD”, “Cable STB”,
3.
“Satellite STB”, “PVR STB”, “AV Receiver”, “Game”, “Camcorder”, “PC”, “TV”, “IPTV”, “Blu-Ray”, “HD DVD”, “Digital Media Adapter” input source, then press the ENTER button. Press the EXIT button to exit.
When a PC with a resolution of 1920 x 1080@60Hz is connected to the
HDMI IN 2 port, you should set the “HDMI2/DVI” mode to “PC” in the “Edit Name” of the “Input” mode.
Input
AV1 : ----
AV2 : ----
S-Video : ----
Component1 : ----
Component2 : ----
PC : ----
HDMI1 : ----
AV1 : ----
AV2 : ----
S-Video : ----
Component1 : ----
Component2 : ----
PC : ----
HDMI1 : ----
Source List
Edit Name
Edit Name
Enter ReturnMove
Edit Name
----
VCR
DVD
Cable STB
Satellite STB
PVR STB
Enter ReturnMove

Picture Control

Changing the Picture Standard

You can select the type of picture which best corresponds to your viewing requirements.
1.
Press the MENU button to display the menu.
Press the ENTER button to select “Picture”.
2. Press the ENTER button to select “Mode”. Press the ▲ or ▼ button to select “Dynamic”, “Standard” or “Movie”. Press the ENTER button.
Dynamic: Selects the picture for high-denition in a bright room.
Standard: Selects the picture for the optimum display in a normal
• environment.
Movie: Selects the picture for viewing movies in a dark room.
3. Press the EXIT button to exit.
Picture
Mode
Backlight : 7
Contrast : 95
Brightness : 45
Sharpness : 50
Color : 50
Tint (G/R) : G50/R50
Detailed Settings
Picture
Mode
Backlight : 7
Contrast : 95
Brightness : 45
Sharpness : 50
Color : 50
Tint (G/R) : G50/R50
Detailed Settings
:
:
Standard
Dynamic
Dynamic
Standard
Movie
Easy Setting
1.
Press the TOOLS button on the remote control.
2.
Press the ▲ or ▼ button to select “Picture Mode”.
3. Press the ◄ or ► button to select the required option.
4. Press the EXIT or TOOLS button to exit.

Customizing the Picture Settings

Your television has several setting options that allow you to control the picture quality.
1.
To select the desired picture mode, follow the “Changing the Picture
Standard” instructions numbers 1 and 2.
2.
Press the ▲ or ▼ button to select “Backlight”, “Contrast”, “Brightness”,
“Sharpness”, “Color” or “Tint(G/R)”, then press the ENTER button.
3. Press the ◄ or ► button to decrease or increase the value of a particular
item. Press the ENTER button.
Press the EXIT button to exit.
When you make changes to “Backlight”, “Contrast”, “Brightness”, “Sharpness”, “Color” or “Tint(G/R)”, the OSD will be adjusted accordingly.
In PC mode, you can only make changes to “Backlight”, “Contrast” and “Brightness”.
Settings can be adjusted and stored for each external device you have connected to an input of the TV.
The energy consumed during use can be signicantly reduced if the level
of brightness of the picture is reduced, and that this will reduce the overall running cost.
Backlight: Adjusts the brightness of LCD back light.
Contrast: Adjusts the contrast level of the picture.
Brightness: Adjusts the brightness level of the picture.
Sharpness: Adjusts the edge denition of the picture.
Color: Adjusts color saturation of the picture.
Tint(G/R): Adjusts the color tint of the picture.
TOOLS
Device List
Picture Mode ◄ Standard ►
Sound Mode : Custom
Sleep Timer : Off
Add to Favorite
Switch to Cable
Move Adjust e Exit
Mode : Standard
Picture
Backlight : 7
Contrast : 95
Brightness : 45
Sharpness : 50
Color : 50
Tint (G/R) : G50/R50
Detailed Settings
Picture Options
7Backlight
Enter ReturnAdjustMove
English - 18
English - 19

Adjusting the Detailed Settings

Samsung’s new TVs allow you to make even more precise picture settings than previous models. See below to adjust detailed picture settings.
Activating Detailed Settings
Press the MENU button to display the menu.
1.
Press the ENTER button to select “Picture”.
2. Press the ENTER button to select “Mode”.
Press the ▲ or ▼ button to select “Standard” or “Movie”, then press the
ENTER button.
“Detailed Settings” is available in “Standard” or “Movie” mode.
Picture
Mode
Backlight : 5
Contrast : 95
Brightness : 50
Sharpness : 20
Color : 50
Tint (G/R) : G50/R50
Detailed Settings
:
Movie
3.
Press the ▲ or ▼ button to select “Detailed Settings”, then press the
ENTER button.
In PC mode, you can only make changes to “Dynamic Contrast”, “Gamma” and “White Balance” from among the “Detailed Settings” items.
Setting the Black adjust
You can select the black level on the screen to adjust the screen depth.
4.
Press the ▲ or ▼ button to select “Black adjust”, then press the ENTER
button.
5.
Press the ▲ or ▼ button to select “Off”, “Low”, “Medium” or “High”.
Press the ENTER button.
Off: Turns off the black adjustment function.
Low: Sets the black color depth to low.
Medium: Sets the black color depth to medium.
High: Sets the black color depth to high.
Setting the Dynamic Contrast
You can adjust the screen contrast so that the optimal contrast is provided.
6.
Press the ▲ or ▼ button to select “Dynamic Contrast”, then press the
ENTER button.
7. Press the ▲ or ▼ button to select “Off”, “Low”, “Medium” or “High”.
Press the ENTER button.
Off: Turns off the dynamic contrast adjustment function.
Low: Sets the dynamic contrast to low.
Medium: Sets the dynamic contrast to medium.
High: Sets the dynamic contrast to high.
Color : 50
Tint (G/R) : G50/R50
Picture
Detailed Settings
Picture Options
Picture Reset
Detailed Settings
Black Adjust : Off
Dynamic Contrast : Off
Gamma : 0
Color Space : Auto
White Balance
Flesh Tone : 0
Edge Enhancement : Off
Return
EnterMove
Off
Low
Black Adjust :
Detailed Settings
Black Adjust : Off
Dynamic Contrast : Off
Gamma : 0
Color Space : Auto
White Balance
Flesh Tone : 0
Edge Enhancement : Off
Dynamic Contrast :
Medium
High
EnterMove
EnterMove
Off
Low
Medium
High
EnterMove
Return
Return
Return
Adjusting the Gamma
You can adjust the Primary Color (Red, Green, Blue) Intensity. (-3 ~ +3)
8.
Press the ▲ or ▼ button to select “Gamma”, then press the ENTER
button.
9.
Press the ◄ or ► button to decrease or increase the value.
Press the ENTER button.
Setting the Color Space
Color space is a color matrix composed of red, green and blue colors. Select your favorite color space to experience the most natural color.
10.
Press the ▲ or ▼ button to select “Color Space”, then press the ENTER
button.
11.
Press the ENTER button again to select “Color Space”.
12. Press the ▲ or ▼ button to select “Auto”, “Native” or “Custom”. Press the ENTER button.
Auto: Auto Color Space automatically adjusts to the most natural color
• tone based on program sources.
Native: Native Color Space offers deep and rich color tone.
Custom: Adjusts the color range to suit your preference.
• (see “Customizing the Color Space”)
Detailed Settings
Black Adjust : Off
Dynamic Contrast : Off
Gamma : 0
Color Space : Auto
White Balance
Flesh Tone : 0
Edge Enhancement : Off
Return
EnterMove
Gamma
0
Return
EnterAdjust
Detailed Settings
Black Adjust : Off
Dynamic Contrast : Off
Gamma : 0
Color Space : Auto
White Balance
Flesh Tone : 0
Edge Enhancement : Off
Return
EnterMove
Color Space
Color Space : Auto
Color : Red
Red 50
Green 0
Blue 0
Reset
Customizing the Color Space
Press the ▲ or ▼ button to select “Color”, then press the ENTER button.
13.
“Color” is available when “Color Space” is set to “Custom”.
14.
Press the ▲ or ▼ button to select “Red”, “Green”, “Blue”, “Yellow”, “Cyan” or
“Magenta”. Press the ENTER button.
15. Press the ▲ or ▼ button to select “Red”, “Green”, or “Blue” to change it.
Press the ENTER button.
16. Press the ◄ or ► button to decrease or increase the value of a particular
item. Press the ENTER button.
In “Color”, you can adjust the RGB values for the selected color.
To reset the adjusted RGB value, select “Reset”.
Red: Adjusts the red saturation level of the selected color.
Green: Adjusts the green saturation level of the selected color.
Blue: Adjusts the blue saturation level of the selected color.
Reset: Resets the color space to the default values.
Changing the adjustment value will refresh the adjusted screen.
Settings can be adjusted and stored for each external device you have connected to an input of the TV. For example, if you have a DVD player connected to HDMI 1 and it is currently selected, settings and adjustments will be saved for the DVD player.
English - 20
Return
EnterMove
Auto
Color Space
Color Space
AdjustMove
Native
Custom
EnterMove
EnterMove
Red
Green Blue Yellow Cyan Magenta
EnterMove
Enter Return
Return
Return
Return
50Red
Color Space :
Color Space : Custom
Color : Red
Red 50
Green 0
Blue 0
Reset
Color :
English - 21
Adjusting the White Balance
You can adjust the color temperature for more natural picture colors.
17.
Press the ▲ or ▼ button to select “White Balance”, then press the
ENTER button.
18. Select the required option by pressing the ▲ or ▼ button, then press the
ENTER button.
19. Press the ◄ or ► button to decrease or increase the value of a particular
item. Press the ENTER button.
R-Offset: Adjusts the red color darkness.
G-Offset: Adjusts the green color darkness.
B-Offset: Adjusts the blue color darkness.
R-Gain: Adjusts the red color brightness.
G-Gain: Adjusts the green color brightness.
B-Gain: Adjusts the blue color brightness.
Reset: The previously adjusted white balance will be reset to the
• factory defaults.
Changing the adjustment value will refresh the adjusted screen.
Detailed Settings
Black Adjust : Off
Dynamic Contrast : Off
Gamma : 0
Color Space : Auto
White Balance
Flesh Tone : 0
Edge Enhancement : Off
Return
Move
White Balance
R-Offset 25
G-Offset 25
B-Offset 25
R-Gain 25
G-Gain 25
B-Gain 25
Reset
White Balance
Enter
EnterMove
Return
25R-Offset
Enter ReturnAdjustMove
Adjusting the Flesh Tone
You can emphasize the pink ‘esh tone’ in the picture.
20.
Press the ▲ or ▼ button to select “Flesh Tone”, then press the ENTER
button.
21.
Press the ◄ or ► button to decrease or increase the value.
Press the ENTER button.
Changing the adjustment value will refresh the adjusted screen.
Setting the Edge Enhancement
You can emphasize object boundaries in the picture.
22.
Press the ▲ or ▼ button to select “Edge Enhancement”, then press the
ENTER button.
23. Press the ▲ or ▼ button to select “Off” or “On”. Press the ENTER button.
Detailed Settings
Black Adjust : Off
Dynamic Contrast : Off
Gamma : 0
Color Space : Auto
White Balance
Flesh Tone : 0
Edge Enhancement : Off
Return
Flesh Tone
Enter
0
Return
EnterAdjust
Return
Enter
Off
On
Return
EnterMove
Move
Detailed Settings
Dynamic Contrast : Off
Gamma : 0
Color Space : Auto
White Balance
Flesh Tone : 0
Edge Enhancement : Off
xvYCC : Off
Move
Edge Enhancement :
Setting the xvYCC
Setting the xvYCC mode to “On” increases detail and color space when watching movies from an external device (ie. DVD player) connected to the HDMI or Component IN jacks.
24.
Press the ▲ or ▼ button to select “xvYCC”, then press the ENTER
button.
25.
Press the ▲ or ▼ button to select “Off” or “On”.
Press the ENTER button.
“xvYCC” is available when the picture mode is set to “Movie”, and the
external input is set to “HDMI” or “Component” mode.
Detailed Settings
Dynamic Contrast : Off
Gamma : 0
Color Space : Auto
White Balance
Flesh Tone : 0
Edge Enhancement : Off
xvYCC : Off
Return
Move
Enter
xvYCC :

Resetting the Picture Settings to the Factory Defaults

1. To select the desired picture mode, follow the “Changing the Picture Standard” instructions numbers 1 and 2. (see page 18)
Press the ▲ or ▼ button to select “Picture Reset”, then press the
2.
ENTER button.
3. Press the ▲ or ▼ button to select “OK” or “Cancel”, then press the
ENTER button.
Press the EXIT button to exit.
Each mode can be reset.
Picture
Picture
Off
On
Return
EnterMove
Detailed Settings
Picture Options
PictureReset
Detailed Settings
Picture Options
PictureReset
OK
Cancel
English - 22
English - 23
ConguringPictureOptions
Activating Picture Options
Press the MENU button to display the menu.
1.
Press the ENTER button to select “Picture”.
2. Press the ▲ or ▼ button to select “Picture Options”, then press the ENTER button.
Press the ▲ or ▼ button to select a particular item. Press the ENTER
button. When you are satised with your setting, press the ENTER
In PC mode, you can only make changes to the “Color Tone” and “Size” from
button.
among the items in “Picture Options”.
Tint (G/R) : G50/R50
Detailed Settings
Picture
PictureOptions
Picture Reset
Setting the Color Tone
Follow the “Activating Picture Options” instructions numbers 1 and 2.
1.
2. Press the ▲ or ▼ button to select “Color Tone”, then press the ENTER
button.
Press the ▲ or ▼ button to select “Cool2”, “Cool1”, “Normal”, “Warm1” or
3.
“Warm2”. Press the ENTER button.
“Warm1” or “Warm2” is only activated when the picture mode is “Movie”.
Settings can be adjusted and stored for each external device you have connected to an input of the TV.
Setting the Screen Size
Occasionally, you may want to change the size of the image on your screen. Your
TV comes with six screen size options, each designed to work best with specic
types of video input. Your cable box or satellite receiver may have its own set of screen sizes as well. In general, though, you should view the TV in 16:9 mode as much as possible.
1.
Follow the “Activating Picture Options” instructions numbers 1 and 2.
2. Press the ▲ or ▼ button to select “Size”, then press the ENTER button.
3.
Press the ▲ or ▼ button to select the screen format you want.
Press the ENTER button. Press the EXIT button to exit.
16:9 : Sets the picture to 16:9 wide mode.
Zoom1: Magnies the size of the picture on the screen.
Zoom2: Magnies the size of the picture more than “Zoom1”.
Wide Fit: Enlarges the aspect ratio of the picture to t the entire screen.
4:3 : Sets the picture to 4:3 normal mode.
Just Scan: Use the function to see the full image without any cutoff when HDMI (720p/1080i/1080p), Component (1080i/1080p) or DTV (1080i) signals are input.
Picture Options
Color Tone : Normal
Size : 16:9
Digital NR : Auto
DNle : Off
HDMI Black Level : Normal
Film Mode : Off
Blue Only Mode : Off
Move
Picture Options
Color Tone : Normal
Size : 16:9
Digital NR : Auto
DNle : Off
HDMI Black Level : Normal
Film Mode : Off
Blue Only Mode : Off
Color Tone : Normal
Size : 16:9
Digital NR : Auto
DNle : Off
HDMI Black Level : Normal
Film Mode : Off
Blue Only Mode : Off
16:9
Zoom1
Zoom2
Wide Fit
4:3
Just Scan
Cool2
Cool1
Normal
Warm1
Warm2
Move
Picture Options
Move
Size
Move
ReturnEnter
ReturnEnter
ReturnEnter
ReturnEnter
When Double ( , ) mode has been set in PIP, the Picture Size cannot be set.
Temporary image retention may occur when viewing a static image on the set for more than two hours.
After selecting “Zoom1”, “Zoom2” or “Wide Fit”:
Press the ◄ or ► button to select “Position”, then press the ENTER button. Press the ▲ or ▼ button to move the picture up and down.
Reset: Press the ◄ or ► button to select “Reset”, then press the ENTER
button. You can initialize the setting.
After selecting “Just Scan” in HDMI (1080i/1080p) or Component (1080i/1080p) mode:
Press the ◄ or ► button to select “Position”, then press the ENTER button. Press the ▲, ▼, ◄ or ► button to move the picture.
Reset: Press the ◄ or ► button to select “Reset”, then press the ENTER
button. You can initialize the setting.
HD (High Denition)
16:9
Zoom1
Zoom2
Wide Fit
4:3
Just Scan
16:9
Zoom1
Zoom2
Wide Fit
4:3
Just Scan
Size
Position
Adjust
Size
Position
16:9 - 1080i/1080p (1920x1080), 720p (1280x720)
Adjust
Settings can be adjusted and stored for each external device you have connected to an input of the TV.
Input Source Picture Size
ATV, Video, S-Video, Component (480i, 480p) 16:9, Zoom1, Zoom2, 4:3
DTV(1080i), Component (1080i, 1080p), HDMI (720p, 1080i, 1080P) 16:9, 4:3, Wide Fit, Just Scan
PC 16:9, 4:3
Reset
ReturnEnter
Reset
ReturnEnter
Alternately, you can press the P.SIZE button on the remote control repeatedly
O
to change the picture size.
16:9
16:9
Sets the picture to 16:9 wide mode.
Zoom1 Magnies the size of the picture on
Zoom1 U Move
the screen.
Wide Fit U Move
Wide Fit
Enlarges the aspect ratio of the
4:3
Sets the picture to 4:3 normal mode.
4:3 Just Scan
picture to t the entire screen.
Zoom2 U Move
Zoom2 Magnies the size of the picture more
than “Zoom1”.
Just Scan
Use the function to see the full image without any cutoff when HDMI (720p/1080i/1080p), Component (1080i/1080p) or DTV (1080i) signals are input.
English - 24
English - 25
Setting the Digital Noise Reduction
If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen.
1.
Follow the “Activating Picture Options” instructions numbers 1 and 2.
(Refer to page 23)
2.
Press the ▲ or ▼ button to select “Digital NR”, then press the ENTER
button.
3.
Press the ▲ or ▼ button to select “Off”, “Low”, “Medium”, “High” or “Auto”.
Press the ENTER button.
Off: Turns the screen noise reduction function off.
Low: Reduces screen noise at a low level.
Medium: Reduces screen noise at a medium level.
High: Reduces screen noise at a high level.
Auto: Automatically recognizes and reduces screen noise.
Press the EXIT button to exit.
Picture Options
Color Tone : Normal
Size : 16:9
Digital NR : Auto
DNle : Off
HDMI Black Level : Normal
Film Mode : Off
Blue Only Mode : Off
Move
Picture Options
Color Tone : Normal
Size : 16:9
Digital NR : Auto
DNle : Off
HDMI Black Level : Normal
Film Mode : Off
Blue Only Mode : Off
Off
Low
Medium
High
Auto
ReturnEnter
Setting the DNIe (Digital Natural Image engine)
This TV includes the DNIe function to provide high visual quality. If you set DNIe to on, you can view the screen with the DNIe feature activated.
1.
Follow the “Activating Picture Options” instructions numbers 1 and 2.
(Refer to page 23)
2.
Press the ▲ or ▼ button to select “DNIe”, then press the ENTER
button.
3.
Press the ▲ or ▼ button to select “Off” or “On”, then press the ENTER
button.
Off: Switches off the DNIe mode.
On: Switches on the DNIe mode.
Press the EXIT button to exit.
DNIe™ (Digital Natural Image engine)
This feature brings you a more detailed image with 3D noise reduction and detail, contrast and white enhancement.
“DNIe” is only available in “Dynamic” mode.
Setting the HDMI Black Level
You can select the black level on the screen to adjust the screen depth.
1.
Follow the “Activating Picture Options” instructions numbers 1 and 2.
(Refer to page 23)
2.
Press the ▲ or ▼ button to select “HDMI Black Level”, then press the
ENTER button.
3. Press the ▲ or ▼ button to select “Normal” or “Low”, then press the
ENTER button.
Normal: The screen gets brighter.
Low: The screen gets darker.
This function is active only when an external device is connected to the TV via HDMI. “HDMI Black Level” function may not be compatible with all external devices.
Press the EXIT button to exit.
Move
Picture Options
Color Tone : Cool1
Size : 16:9
Digital NR : Auto
DNle : On
HDMI Black Level : Normal
Film Mode : Off
Blue Only Mode : Off
Move
Picture Options
Color Tone : Cool1
Size : 16:9
Digital NR : Auto
DNle : On
HDMI Black Level : Normal
Film Mode : Off
Blue Only Mode : Off
Color Tone : Normal
Size : 16:9
Digital NR : Auto
DNle : Off
HDMI Black Level : Normal
Film Mode : Off
Blue Only Mode : Off
Color Tone : Normal
Size : 16:9
Digital NR : Auto
DNle : Off
HDMI Black Level : Normal
Film Mode : Off
Blue Only Mode : Off
Off
On
Move
Picture Options
Move
Picture Options
Normal
Low
ReturnEnter
ReturnEnter
ReturnEnter
ReturnEnter
Move
ReturnEnter
Setting the Film Mode
The TV can be set to automatically sense and process lm signals from all
sources and adjust the picture for optimum quality.
1.
Follow the “Activating Picture Options” instructions numbers 1 and 2.
(Refer to page 23)
2.
Press the ▲ or ▼ button to select “Film Mode”, then press the ENTER
button.
Picture Options
Color Tone : Normal
Size : 16:9
Digital NR : Auto
DNle : Off
HDMI Black Level : Normal
Film Mode : Off
Blue Only Mode : Off
3. Press the ▲ or ▼ button to select “Off” or “Auto”, then press the ENTER button.
Press the EXIT button to exit.
“Film mode” is supported in TV, Video, S-Video,
Component (480i / 1080i) and HDMI (480i / 1080i).
Setting the Blue Only Mode
This function is for AV device measurement experts. This function displays the blue signal only by removing the red and green signals from the video signal so as to provide a Blue Filter effect that is used to adjust the Color and Tint of video equipment such as DVD players, Home Theaters, etc.
Using this function, you can adjust the Color and Tint to preferred values appropriate to the signal level of each video device using the Red/Green/Blue/ Cyan/Magenta/Yellow Color Bar Patterns, without using an additional Blue Filter.
1.
Follow the “Activating Picture Options” instructions numbers 1 and 2.
(Refer to page 23)
2.
Press the ▲ or ▼ button to select “Blue Only Mode”, then press the
ENTER button.
3. Press the ▲ or ▼ button to select “Off” or “On”, then press the ENTER button.
Press the EXIT button to exit.
“Blue Only Mode” is available when the picture mode is set to “Movie” or
“Standard”.
Move
Picture Options
Color Tone : Normal
Size : 16:9
Digital NR : Auto
DNle : Off
HDMI Black Level : Normal
Film Mode : Off
Blue Only Mode : Off
Color Tone : Normal
Size : 16:9
Digital NR : Auto
DNle : Off
HDMI Black Level : Normal
Film Mode : Off
Blue Only Mode : Off
Color Tone : Normal
Size : 16:9
Digital NR : Auto
DNle : Off
HDMI Black Level : Normal
Film Mode : Off
Blue Only Mode : Off
Off
Auto
Move
Picture Options
Move
Picture Options
Off
On
Move
ReturnEnter
ReturnEnter
ReturnEnter
ReturnEnter
English - 26
English - 27

Viewing Picture-in-Picture

You can use the PIP feature to simultaneously watch the TV tuner (analog broadcasts only) and one external video source. (See page 33 to select the PIP picture sound.) This product has one built-in tuner, which does not allow PIP to function in the same mode. Please see ‘PIP Settings’ below for details.
While V-Chip (See page 49) is in operation, the PIP function cannot be used.
Activating Picture-in-Picture
1.
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Press the ▲ or ▼ button to select “PIP”, then press the ENTER button.
2.
Press the ENTER button again. Press the ▲ or ▼ button to select “On”, then press the ENTER button.
If you turn the TV off while watching in PIP mode and turn it on again, the
PIP window will disappear.
You can view Analog TV broadcasts on the PIP screen (sub-picture) when
the main picture is from an external device connected to HDMI 1, HDMI/DVI 2, HDMI 3, Component1, 2 or PC.
When the resolution is set to 1920 x1080@60Hz and the current input
port is either PC or HDMI, and PIP is turned on, the main picture may not be displayed clearly.
PIP Settings
Main picture Sub picture
Component 1, 2
HDMI 1, HDMI/DVI 2, HDMI 3PCAnalog TV broadcasts only
Changing the Size of the PIP Window
3.
Press the ▲ or ▼ button to select “Size”, then press the ENTER button. Press the ▲ or ▼ button to select the required option, then press the ENTER
button.
You may notice that the picture in the PIP window becomes slightly
unnatural when you use the main screen to view a game or karaoke.
Entertainment : Off Energy Saving : Off
Setup
PIP
SW Upgrade
PIP
PIP :
Size :
Position :
Air/Cable : Air
Channel : Air 11
Move
PIP
PIP : On
Size :
Position :
Air/Cable : Air
Channel : Air 11
Off
Off
On
ReturnEnter
Changing the Position of the PIP Window
Press the ▲ or ▼ button to select “Position”, then press the ENTER
4.
button. Press the ▲ or ▼ button to select the required option, then press the ENTER
button.
In Double Window (
) and Double Wide ( ) modes, “Position”
cannot be selected.
Move
PIP
PIP : On
Size :
Position :
Air/Cable : Air
Channel : Air 11
Move
ReturnEnter
ReturnEnter
Changing the PIP Channel
Press the ▲ or ▼ button to select “Air/Cable”, then press the ENTER
5.
button.
6.
Press the ▲ or ▼ button to select “Air” or “Cable”, then press the ENTER
button.
PIP
PIP : On
Size :
Position :
Air/Cable : Air
Channel : Air 11
Air
Cable
7. Press the ▲ or ▼ button to select “Channel”, then press the ENTER button.
8.
Press the ▲ or ▼ button to select the desired channel in the PIP window.
Press the ENTER button.
You can select only analog TV broadcasts on the PIP screen
(sub-picture).
Press the EXIT button to exit.
Easy Setting
1.
Press the TOOLS button on the remote control.
2.
Press the ▲ or ▼ button to select “PIP”, then press the ENTER button.
3. Press the ▲ or ▼ button to select a particular item.
4. Press the ◄ or ► button to select the required option.
5. Press the EXIT or TOOLS button to exit.
Move
PIP
PIP : On
Size :
Position :
Air/Cable : Air
Channel : Air 11
Picture Mode : Standard
Sound Mode : Custom
Sleep Timer : Off
PIP
PIP ◄ Off ►
Size :
Posion :
Air/Cable : Air
Channel : Air 11
Move
Device List
Air 11
TOOLS
PIP
EnterMove
Adjust
ReturnEnter
ReturnEnter
e
Exit
Return
English - 28
Loading...
+ 168 hidden pages