Samsung LN22B360C5DUZA User Manual [en, es]

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.

Comuníquese con SAMSUNG WORLDWIDE

Si desea formular alguna pregunta o comentario en relación con los productos de Samsung, comuníquese con el centro de atención al cliente de SAMSUNG.

Country

CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca

U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com/us

Customer Care Center

Web Site Address

Samsung Electronics Canada Inc., Customer Service 55 Standish Court Mississauga, Ontario L5R 4B2 Canada

Samsung Electronique Canada Inc., Service à la Clientèle 55 Standish Court Mississauga, Ontario L5R 4B2 Canada

Samsung Electronics America, Inc. 105 Challenger Road Ridgefield Park, NJ 07660-0511

LCD TV

user manual

BN68-01975A-01

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service, please register your product at

www.samsung.com/register

Model Serial No.

Important Warranty Information Regarding Television Format Viewing

❑

See the warranty card for more information on warranty terms.

Wide screen format LCD Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to

ll the screen if your model offers this feature and the images are constantly moving. Displaying stationary graphics and images

on screen, such as the dark sidebars on nonexpanded standard format television video and programming, should be limited to no more than 5% of the total television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary images that exceed the above guidelines can cause uneven aging of LCD Displays that leave subtle, but permanent burned-in ghost images in the LCD picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars.

On LCD models that offer picture sizing features, use these controls to view different formats as a full screen picture. Be careful in the selection and duration of television formats used for viewing. Uneven LCD aging as a result of format selection

and use, as well as burned-in images, are not covered by your Samsung limited warranty.

SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY STATEMENT

●

Subject to the requirements, conditions, exclusions and limitations of the original Limited Warranty supplied with Samsung Electronics (SAMSUNG) products, and the requirements, conditions, exclusions and limitations contained herein, SAMSUNG will additionally provide Warranty Repair Service in the United States on SAMSUNG products purchased in Canada, and

in Canada on SAMSUNG products purchased in the United States, for the warranty period originally specied, and to the

Original Purchaser only. The above described warranty repairs must be performed by a SAMSUNG Authorized Service Center. Along with this

Statement, the Original Limited Warranty Statement and a dated Bill of Sale as Proof of Purchase must be presented to the Service Center. Transportation to and from the Service Center is the responsibility of the purchaser.

Conditions covered are limited only to manufacturing defects in material or workmanship, and only those encountered in normal use of the product.

Excluded, but not limited to, are any originally specied provisions for, in-home or on-site services, minimum or maximum

repair times, exchanges or replacements, accessories, options, upgrades, or consumables. For the location of a SAMSUNG Authorized Service Center, please call toll-free:

In the United States : 1-800-SAMSUNG (1-800-726-7864)

In Canada : 1-800-SAMSUNG

Precautions When Displaying a Still Image

❑

A still image may cause permanent damage to the TV screen

Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention. This image

●

retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

●

Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the left,

right and center of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause a similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.

CONTENTS

English

General Information

List of Features .....................................................................2

■

Accessories

■

Viewing the Control Panel

■

Viewing the Connection Panel

■

Remote Control

■

Installing Batteries in the Remote Control

..........................................................................2

....................................................3

..............................................4

....................................................................6

............................6

Connections (LN19B360, LN22B360)

■

Connecting VHF and UHF Antennas ....................................7

■

Connecting Cable TV

■

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via HDMI

■

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via DVI

■

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via Component cables

■

Connecting a VCR

■

Connecting a Digital Audio System

■

Connecting an Amplier / DVD Home Theater

■

Connecting a Camcorder....................................................12

■

Connecting a PC

...........................................................7

............................8

.............................................9

.......9

..............................................................10

....................................10

...................11

................................................................13

Connections (LN26B360, LN32B360)

■

Connecting VHF and UHF Antennas ..................................14

■

Connecting Cable TV

■

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via HDMI

■

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via DVI

■

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via Component cables

■

Connecting a VCR

■

Connecting a Digital Audio System

■

Connecting an Amplier / DVD Home Theater

■

Connecting a Camcorder....................................................19

■

Connecting a PC

.........................................................14

..........................15

...........................................16

.....16

..............................................................17

....................................17

...................18

................................................................20

Operation

■

Viewing the menus .............................................................21

■

Plug & Play Feature............................................................22

Channel Control

■

Conguring the Channel Menu ...........................................23

■

Managing Channels ...........................................................23

Picture Control

■

Conguring the Picture Menu .............................................25

■

Using Your TV as a Computer (PC) Display

■

Setting up the TV with your PC

..........................................28

.......................27

Sound Control

■

Conguring the Sound Menu ..............................................29

Setup

■

Conguring the Setup Menu ...............................................30

Input / Support

■

Conguring the Input Menu ................................................34

■

Conguring the Support Menu............................................34

Appendix

■

Troubleshooting ..................................................................36

■

Installing the Stand

■

Disconnecting the Stand.....................................................37

■

How to Adjust the Stand (LN19B360)

■

How to Adjust the Angle of the TV (LN19B360)

■

Installing VESA Compliant Mounting Devices (LN19B360)

■

Using the Decoration Covers (LN19B360)

■

Wall Mount Kit Specications (VESA)

■

Using the Anti-Theft Kensington Lock

■

Securing the TV to the Wall

■

Specications

■

Dimensions

.............................................................37

.................................38

..................38

.........................39

................................40

................................................41

.....................................................................42

.........................................................................43

License

❑

TruSurround HD, SRS and Symbol are trademarks of SRS Labs, Inc. TruSurround HD technology is incorporated under license from SRS Labs, Inc.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Symbol

❑

N O T

Note One-Touch Button TOOL Button

English - 1

GENERAL INFORMATION

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.

Product design and specications may be changed without notice in order to enhance product performance.

List of Features

Adjustable picture settings that can be stored in the TV’s memory.

● Automatic timer to turn the TV on and off.

●

A special sleep timer.

● Excellent Digital Interface & Networking :

● With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Cable Box/Satellite receiver (Set-Top

● Box) needed.

HDMI/DVI connection of your PC to this TV.

●

Excellent Picture Quality

● SRS TruSurround HD provides a virtual surround system.

●

Accessories

Remote Control

(BN59-00857A) &

Batteries (AAA x 2)

Cover-Bottom (LN22B360: BN63-04269A) (LN26B360: BN63-04269A) (LN32B360: BN63-05326A)

Decoration Cover

(LN19B360: Right- BN63-04242A

Left- BN63-04254A)

Please make sure the following items are included with your LCD TV. If any items The items color and shape may vary depending on the model.

Power Cord

(3903-000144)

Screw (M4 X L16) (LN22B360: 6002-001294) (LN26B360: 6002-001294) (LN32B360: 6002-001294)

Owner’s Instructions Warranty Card /

TV-Holder & Screw (M4 X L16)

(LN32B360: BN96-10788A)

Screw (M4 X L14)

(LN32B530: 6003-001334)

Cleaning Cloth

(BN63-01798B)

Wall Mount kit

(LN19B360: BN96-04960A)

Safety Guide Manual

are missing, contact your dealer.

English - 2

English - 3

Viewing the Control Panel

The product color and shape may vary depending on the model.

You can use a button by pressing the side panel buttons.

SOURCEE: Toggles between all the available input sources. In the on-screen menu, use this button as you use the

ENTERE button on the remote control.

MENU: Press to see an on-screen menu of your TV’s features.

3 y

◄ and ► buttons on the remote control.

4 Z

on the remote control.

5 P 6

SPEAKERS

REMOTE CONTROL SENSOR: Aim the remote control towards this spot on the TV.

POWER INDICATOR: Blinks and turns off when the power is on and lights up in stand-by mode.

: Press to increase or decrease the volume. In the on-screen menu, use the

: Press to change channels. In the on-screen menu, use the

(POWER): Press to turn the TV on and off.

buttons as you would use the ▼ and ▲ buttons

buttons as you would use the

Viewing the Connection Panel

!@#

21 3 4 5 7 8

8 6 3 # 2

1!@

!@#

21 3 4 5 7 8

LN19B360, LN22B360



[TV Rear Panel]

LN26B360, LN32B360



[TV Rear Panel]

The product color and shape may vary depending on the model.

English - 4

English - 5

EX-LINK

Connector for service only.

–

DIGITAL AUDIO OUT (OPTICAL)

Connects to a Digital Audio component such as a Home theater receiver.

–

PC IN [PC] / [AUDIO]

Connects to the video and audio output jacks on your PC.

–

4 H

(HEADPHONE)

Connects a set of external headphones for private listening.

–

HDMI (DVI) IN / DVI AUDIO IN [R-AUDIO-L] (LN19B360, LN22B360)

Connects to the HDMI jack of a device with an HDMI output.

–

No sound connection is needed for an HDMI to HDMI connection.

Use the HDMI (DVI) IN jack for DVI connection to an external device. Use a DVI to HDMI cable or DVI-HDMI adapter

(DVI to HDMI) for video connection and the DVI AUDIO IN [R-AUDIO-L] jacks for audio. When using an HDMI/DVI cable connection, you must use the HDMI (DVI) IN jack.

You can also use the ports to connect to a PC.

HDMI IN 1, 2 / DVI IN(HDMI1)[R-AUDIO-L] (LN26B360, LN32B360)

Connects to the HDMI jack of a device with an HDMI output.

–

No sound connection is needed for an HDMI to HDMI connection.

Use the HDMI IN 1 jack for DVI connection to an external device. Use a DVI to HDMI cable or DVI-HDMI adapter

(DVI to HDMI) for video connection and the DVI IN (HDMI1) [R-AUDIO-L] jacks for audio. When using an HDMI/DVI cable connection, you must use the HDMI IN 1 jack.

You can also use the ports to connect to a PC.

SERVICE

–

Connector for software upgrades.

ANT IN

Connects to an antenna or cable TV system.

–

POWER INPUT

Connects the supplied power cord.

–

KENSINGTON LOCK

The Kensington Lock (optional) is a device used to physically x the system when used in a public place. If you want to

–

use a locking device, contact the dealer where you purchased the TV.

The location of the Kensington Lock may be different depending on its model.

AV IN

Video and audio inputs for external devices, such as a camcorder or VCR.

–

COMPONENT IN

Connects Component video / audio.

–

AUDIO OUT

Connects to the audio input jacks on your Amplier/Home theater.

–

$ % ^ &

(

) a

3 4

9 0

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.

The performance of the remote control may be affected by bright light.

The product color and shape may vary depending on the model.

POWER: Turns the TV on and

off.

NUMERIC BUTTONS: Press to

change the channel.

_: Press to select additional

channels (digital) being broadcast by the same station. For example, to select channel ‘54-3’, press ‘54’, then press _ and ‘3’.

MUTE M: Press to temporarily

cut off the sound.

5 y

decrease the volume.

CH LIST: Used to display

Channel Lists on the screen.

TOOLS: Use to quickly select

frequently used functions.

INFO: Press to display

information on the TV screen.

COLOR BUTTONS: Use these

buttons in the Channel list menus etc.

P.SIZE: Picture size selection.

TV: Selects the TV mode directly.

: Press to increase or

PRE-CH: Enables you to return

to the previous channel you were watching.

# z

channels.

SOURCE: Press to display

and select the available video sources.

FAV.CH: Press to switch to your

favorite channels.

MENU: Displays the main on-

screen menu.

RETURN: Returns to the

previous menu.

 UP▲/DOWN▼/LEFT◄/

RIGHT►/ENTERE: Use to

select on-screen menu items and change menu values.

(

EXIT: Press to exit the menu.

)

CC: Controls the caption

decoder.

MTS: Press to choose stereo,

mono or Separate Audio Program (SAP broadcast).

: Press to change

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the gure.

2. Install two AAA size batteries.

Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram inside the

compartment.

3. Replace the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the

remote control for a long time. (Assuming typical TV usage, the batteries should last for about one year.)

If the remote control doesn’t work, check the following:

Is the TV power on?

●

Are the plus and minus ends of the batteries reversed?

●

Are the batteries drained?

●

Is there a power outage or is the power cord unplugged?

● Is there a special uorescent light or neon sign nearby?

●

English - 6

English - 7

CONNECTIONS (LN19B360, LN22B360)

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like the diagram to the right, see ‘Antennas with 300

Ω Flat Twin Leads’ below.

If your antenna has one lead that looks like the diagram to the right, see ‘Antennas with 75 Ω

Round Leads’. If you have two antennas, see ‘Separate VHF and UHF Antennas’.

Antennaswith300ΩFlatTwinLeads

If you are using an off-air antenna (such as a roof antenna or ‘rabbit ears’) that has 300Ω twin at leads, follow the directions below.

1. Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not

supplied). Use a screwdriver to tighten the screws.

2. Plug the adaptor into the ANT IN terminal on the back of the TV.

Antennaswith75ΩRoundLeads

Plug the antenna lead into the ANT IN terminal on the back of the TV.

ANT IN

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

1. Connect both antenna leads to the combiner.

2. Plug the combiner into the ANT IN terminal on the bottom of the rear panel.

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

Plug the incoming cable into the ANT IN terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable

channels.

Connecting to a Cable Box that Descrambles All Channels

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled ‘ANT OUT’, ‘VHF OUT’ or simply, ‘OUT’.

2. Connect the other end of this cable to the ANT IN terminal on the back of the TV.

UHF

VHF

ANT IN ANT OUT

UHF

VHF

ANT IN

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a twoway splitter, an RF (A/B) switch and four lengths of RF cable. (These items are available at most electronics stores.)

ANT IN

Incoming cable

Splitter

Cable Box

RF (A/B) Switch

1. Find and disconnect the cable that is connected to the ANT IN terminal on your cable box.

This terminal might be labeled ‘ANT IN’, ‘VHF IN’ or simply, ‘IN’.

2. Connect this cable to a two-way splitter.

3. Connect an RF cable between the OUTPUT terminal on the splitter and the IN terminal on the cable box.

4. Connect an RF cable between the ANT OUT terminal on the cable box and the B–IN terminal on the RF(A/B) switch.

5. Connect another cable between the other OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch.

6. Connect the last RF cable between the OUT terminal on the RF (A/B) switch and the ANT IN terminal on the rear of the TV.

After you have made this connection, set the A/B switch to the ‘A’ position for normal viewing. Set the A/B switch to the ‘B’ position to view scrambled channels. (When you set the A/B switch to ‘B’, you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.

DVD / Blu-ray player / Cable Box /

TV Rear Panel

Satellite receiver (Set-Top Box)

TV Rear

HDMI Cable (Not supplied)

1. Connect an HDMI Cable between the HDMI (DVI) IN jack on the TV and the HDMI jack on the DVD / Blu-ray Player or Cable

Box / Satellite receiver (Set-Top Box). What is HDMI?

HDMI(High-Denition Multimedia Interface), is an interface that enables the transmission of digital audio and video signals

●

using a single cable. The difference between HDMI and DVI is that the HDMI device is smaller in size and has the HDCP (High Bandwidth Digital

●

Copy Protection) coding feature installed.

Each DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) has a dif

N N

The TV may not output sound and pictures may be displayed with abnormal color when DVD / Blu-ray player / Cable Box /

ferent back panel conguration.

Satellite receiver (Set-Top Box) supporting HDMI versions older than 1.3 are connected. When connecting an older HDMI cable and there is no sound, connect the HDMI cable to the HDMI (DVI) IN jack and the audio cables to the DVI AUDIO IN [R-AUDIO-L] jacks on the back of the TV. If this happens, contact the company that provided the DVD / Blu-ray player /

Cable Box / Satellite receiver (Set-Top Box) to conrm the HDMI version, then request an upgrade.

HDMI cables that are not 1.3 may cause annoying icker or no screen display.

English - 8

English - 9

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via DVI

This connection can only be made if there is a DVI Output connector on the external device.

TV Rear Panel

DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box)

Audio Cable (Not supplied)

DVI to HDMI Cable (Not supplied)

1. Connect a DVI to HDMI Cable or DVI-HDMI Adapter between the HDMI (DVI) IN jack on the TV and the DVI jack on the DVD /

Blu-ray player / Cable Box / Satellite receiver (Set-Top Box).

2. Connect Audio Cables between the DVI AUDIO IN [R-AUDIO-L] jack on the TV and the DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box).

Each DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) has a dif

When connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box), match the color of the connection

terminal to the cable.

ferent back panel conguration.

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via Component cables

The rear panel jacks on your TV make it easy to connect a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) to your TV.

TV Rear Panel

DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box)

Audio Cable (Not supplied)

Component Cable (Not supplied)

1. Connect a Component Cable between the COMPONENT IN [Y, PB, PR] jacks on the TV and the COMPONENT [Y, PB, PR]

jacks on the DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box).

2. Connect Audio Cables between the COMPONENT IN [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the DVD /

Blu-ray player / Cable Box / Satellite receiver (Set-Top Box).

Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red) for enhanced video quality.

Be sure to match the component video and audio connections. For example, if connecting a Component video cable to COMPONENT IN, connect the audio cable to COMPONENT IN also.

Each DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) has a dif

N N

When connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box), match the color of the connection terminal to the cable.

ferent back panel conguration.

Connecting a VCR

TV Rear Panel

VCR Rear Panel

Audio Cable (Not supplied)

Video Cable (Not supplied)

1. Connect a Video Cable between the AV IN [VIDEO] jack on the TV and the VIDEO OUT jack on the VCR.

2. Connect Audio Cables between the AV IN [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the VCR.

If you have a ‘mono’ (non-stereo) VCR, use a Y-connector (not supplied) to connect to the right and left audio input jacks

of the TV. Alternatively, connect the cable to the ‘R’ jack. If your VCR is stereo, you must connect two cables.

Each VCR has a different back panel conguration.

When connecting a VCR, match the color of the connection terminal to the cable.

Connecting a Digital Audio System

The rear panel jacks on your TV make it easy to connect a Digital Audio System (Home theater/Receiver) to your TV.

Digital Audio System

Optical Cable (Not supplied)

1. Connect an Optical Cable between the DIGITAL AUDIO OUT (OPTICAL) jacks on the TV and the Digital Audio Input jacks on

the Digital Audio System.

When a Digital Audio System is connected to the DIGITAL AUDIO OUT (OPTICAL) jack: Decrease the volume of the TV

and adjust the volume level with the system’s volume control.

5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.

Each Digital Audio System has a different back panel conguration.

When the Home Theater receiver is set to On, you can hear sound output from the TV’s Optical jack. When the TV is

displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digital component such as a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver. If you want to hear 5.1 channel audio, connect the digital audio out jack on DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) directly to an

Amplier or Home Theater, not the TV.

TV Rear Panel

English - 10

English - 11

ConnectinganAmplier/DVDHomeTheater

TV Rear Panel

Amplier/DVDHomeTheater

Audio Cable (Not supplied)

1. Connect Audio Cables between the AUDIO OUT [R-AUDIO-L] jacks on the TV and Audio Input jacks on the Amplier / DVD

Home Theater.

When an audio amplier is connected to the AUDIO OUT [R-AUDIO-L] jacks: Decrease the volume of the TV and adjust

the volume level with the Amplier’s volume control. Each Amplier/DVD Home Theater has a different back panel conguration.

When connecting an Amplier/DVD Home Theater, match the color of the connection terminal to the cable.

Connecting a Camcorder

Using a Video Cable

TV Rear Panel

Camcorder

1. Connect a Video Cable between the AV IN [VIDEO] jack on the TV and the VIDEO OUT jack on the camcorder.

2. Connect Audio Cables between the AV IN [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the camcorder.

Each Camcorder has a different back panel conguration.

When connecting a Camcorder, match the color of the connection terminal to the cable.

Audio Cable (Not supplied)

Video Cable (Not supplied)

Using an HDMI Cable

TV Rear Panel

HD Camcorder

HDMI Cable (Not supplied)

1. Connect a HDMI Cable between the HDMI (DVI) IN jack on the TV and the HDMI OUT jack on the camcorder.

English - 12

English - 13

Connecting a PC

Using a D-Sub Cable

TV Rear Panel

PC Audio Cable (Not supplied)

D-Sub Cable (Not supplied)

1. Connect a D-Sub Cable between PC IN [PC] connector on the TV and the PC output connector on your computer.

2. Connect a PC Audio Cable between the PC IN [AUDIO] jack on the TV and the Audio Out jack of the sound card on your

computer.

When connecting a PC, match the color of the connection terminal to the cable.

Using an HDMI/DVI Cable

TV Rear Panel

3.5 mm Stereo mini-plug/2RCA Cable (Not supplied)

HDMI/DVI Cable (Not supplied)

1. Connect an HDMI/DVI cable between the HDMI (DVI) IN jack on the TV and the PC output jack on your computer.

2. Connect a 3.5 mm Stereo miniplug / 2RCA Cable between the DVI AUDIO IN [R-AUDIO-L] jack on the TV and the Audio Out

jack of the sound card on your computer.

Using an HDMI Cable

TV Rear Panel

HDMI Cable (Not supplied)

1. Connect an HDMI cable between the HDMI (DVI) IN jack on the TV and the PC output jack on your computer.

Each PC has a different back panel conguration.

CONNECTIONS (LN26B360, LN32B360)

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like the diagram to the right, see ‘Antennas with 300

Ω Flat Twin Leads’ below.

If your antenna has one lead that looks like the diagram to the right, see ‘Antennas with 75 Ω

Round Leads’. If you have two antennas, see ‘Separate VHF and UHF Antennas’.

Antennaswith300ΩFlatTwinLeads

If you are using an off-air antenna (such as a roof antenna or ‘rabbit ears’) that has 300Ω twin at leads, follow the directions below.

1. Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not

supplied). Use a screwdriver to tighten the screws.

2. Plug the adaptor into the ANT IN terminal on the back of the TV.

Antennaswith75ΩRoundLeads

Plug the antenna lead into the ANT IN terminal on the back of the TV.

ANT IN

Separate VHF and UHF Antennas

1. Connect both antenna leads to the combiner.

2. Plug the combiner into the ANT IN terminal on the bottom of the rear panel.

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

Plug the incoming cable into the ANT IN terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable

channels.

Connecting to a Cable Box that Descrambles All Channels

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled ‘ANT OUT’, ‘VHF OUT’ or simply, ‘OUT’.

2. Connect the other end of this cable to the ANT IN terminal on the back of the TV.

UHF

VHF

ANT IN ANT OUT

UHF

VHF

ANT IN

English - 14

English - 15

Connecting to a Cable Box that Descrambles Some Channels

ANT IN

Incoming cable

Splitter

Cable Box

RF (A/B) Switch

1. Find and disconnect the cable that is connected to the ANT IN terminal on your cable box.

This terminal might be labeled ‘ANT IN’, ‘VHF IN’ or simply, ‘IN’.

2. Connect this cable to a two-way splitter.

3. Connect an RF cable between the OUTPUT terminal on the splitter and the IN terminal on the cable box.

4. Connect an RF cable between the ANT OUT terminal on the cable box and the B–IN terminal on the RF(A/B) switch.

5. Connect another cable between the other OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch.

6. Connect the last RF cable between the OUT terminal on the RF (A/B) switch and the ANT IN terminal on the rear of the TV.

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.

TV Rear Panel

DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box)

TV Rear

HDMI Cable (Not supplied)

1. Connect an HDMI Cable between the HDMI IN (1 or 2) jack on the TV and the HDMI jack on the DVD Player or Cable Box /

Satellite receiver (Set-Top Box). What is HDMI?

HDMI(High-Denition Multimedia Interface), is an interface that enables the transmission of digital audio and video signals

●

using a single cable. The difference between HDMI and DVI is that the HDMI device is smaller in size and has the HDCP (High Bandwidth Digital

●

Copy Protection) coding feature installed.

Each DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) has a dif

N N

The TV may not output sound and pictures may be displayed with abnormal color when DVD / Blu-ray player / Cable Box /

ferent back panel conguration.

Satellite receiver (Set-Top Box) supporting HDMI versions older than 1.3 are connected. When connecting an older HDMI cable and there is no sound, connect the HDMI cable to the HDMI IN 1 jack and the audio cables to the DVI IN (HDMI 1) [R-AUDIO-L] jacks on the back of the TV. If this happens, contact the company that provided the DVD / Blu-ray player /

Cable Box / Satellite receiver (Set-Top Box) to conrm the HDMI version, then request an upgrade.

HDMI cables that are not 1.3 may cause annoying icker or no screen display.

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via DVI

This connection can only be made if there is a DVI Output connector on the external device.

TV Rear Panel

DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box)

Audio Cable (Not supplied)

DVI to HDMI Cable (Not supplied)

1. Connect a DVI to HDMI Cable or DVI-HDMI Adapter between the HDMI IN 1 jack on the TV and the DVI jack on the DVD /

Blu-ray player / Cable Box / Satellite receiver (Set-Top Box).

2. Connect Audio Cables between the DVI IN (HDMI 1) [R-AUDIO-L] jack on the TV and the DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box).

Each DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) has a dif

When connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box), match the color of the connection

terminal to the cable. When using an HDMI / DVI cable connection, you must use the HDMI IN 1 jack.

ferent back panel conguration.

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via Component cables

The rear panel jacks on your TV make it easy to connect a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) to your TV.

TV Rear Panel

DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box)

Audio Cable (Not supplied)

Component Cable (Not supplied)

1. Connect a Component Cable between the COMPONENT IN [Y, PB, PR] jacks on the TV and the COMPONENT [Y, PB, PR]

jacks on the DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box).

2. Connect Audio Cables between the COMPONENT IN [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the DVD /

Blu-ray player / Cable Box / Satellite receiver (Set-Top Box).

Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red) for enhanced video quality.

Be sure to match the component video and audio connections. For example, if connecting a Component video cable to COMPONENT IN, connect the audio cable to COMPONENT IN also.

Each DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) has a dif

N N

When connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box), match the color of the connection terminal to the cable.

ferent back panel conguration.

English - 16

English - 17

Connecting a VCR

TV Rear Panel

VCR Rear Panel

Audio Cable (Not supplied)

Video Cable (Not supplied)

1. Connect a Video Cable between the AV IN [VIDEO] jack on the TV and the VIDEO OUT jack on the VCR.

2. Connect Audio Cables between the AV IN [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the VCR.

If you have a ‘mono’ (non-stereo) VCR, use a Y-connector (not supplied) to connect to the right and left audio input jacks

of the TV. Alternatively, connect the cable to the ‘R’ jack. If your VCR is stereo, you must connect two cables.

Each VCR has a different back panel conguration.

When connecting a VCR, match the color of the connection terminal to the cable.

Connecting a Digital Audio System

The rear panel jacks on your TV make it easy to connect a Digital Audio System (Home theater/Receiver) to your TV.

TV Rear Panel

Digital Audio System

Optical Cable (Not supplied)

1. Connect an Optical Cable between the DIGITAL AUDIO OUT (OPTICAL) jacks on the TV and the Digital Audio Input jacks on

the Digital Audio System.

When a Digital Audio System is connected to the DIGITAL AUDIO OUT (OPTICAL) jack: Decrease the volume of the TV

and adjust the volume level with the system’s volume control.

5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.

Each Digital Audio System has a different back panel conguration.

When the Home Theater receiver is set to On, you can hear sound output from the TV’s Optical jack. When the TV is

Amplier or Home Theater, not the TV.

ConnectinganAmplier/DVDHomeTheater

TV Rear Panel

Amplier/DVDHomeTheater

Audio Cable (Not supplied)

1. Connect Audio Cables between the AUDIO OUT [R-AUDIO-L] jacks on the TV and Audio Input jacks on the Amplier / DVD

Home Theater.

When an audio amplier is connected to the AUDIO OUT [R-AUDIO-L] jacks: Decrease the volume of the TV and adjust

the volume level with the Amplier’s volume control. Each Amplier/DVD Home Theater has a different back panel conguration.

When connecting an Amplier/DVD Home Theater, match the color of the connection terminal to the cable.

English - 18

English - 19

Connecting a Camcorder

Using a Video Cable

TV Rear Panel

Camcorder

1. Connect a Video Cable between the AV IN [VIDEO] jack on the TV and the VIDEO OUT jack on the camcorder.

2. Connect Audio Cables between the AV IN [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the camcorder.

Each Camcorder has a different back panel conguration.

When connecting a Camcorder, match the color of the connection terminal to the cable.

Audio Cable (Not supplied)

Video Cable (Not supplied)

Using an HDMI Cable

TV Rear Panel

HD Camcorder

HDMI Cable (Not supplied)

1. Connect a HDMI Cable between the HDMI IN (1 or 2) jack on the TV and the HDMI OUT jack on the camcorder.

Connecting a PC

Using a D-Sub Cable

TV Rear Panel

D-Sub Cable (Not supplied)

PC Audio Cable (Not supplied)

1. Connect a D-Sub Cable between PC IN [PC] connector on the TV and the PC output connector on your computer.

2. Connect a PC Audio Cable between the PC IN [AUDIO] jack on the TV and the Audio Out jack of the sound card on your

computer.

When connecting a PC, match the color of the connection terminal to the cable.

Using an HDMI/DVI Cable

TV Rear Panel

3.5 mm Stereo mini-plug/2RCA Cable (Not supplied)

HDMI/DVI Cable (Not supplied)

1. Connect an HDMI/DVI cable between the HDMI IN 1 jack on the TV and the PC output jack on your computer.

2. Connect a 3.5 mm Stereo miniplug / 2RCA Cable between the DVI IN (HDMI 1) [R-AUDIO-L] jack on the TV and the Audio

Out jack of the sound card on your computer.

When using an HDMI/DVI cable connection, you must use the HDMI IN 1 terminal.

Using an HDMI Cable

TV Rear Panel

HDMI Cable (Not supplied)

1. Connect an HDMI cable between the HDMI IN (1 or 2) jack on the TV and the PC output jack on your computer.

Each PC has a different back panel conguration.

English - 20

English - 21

OPERATION

Viewing the menus

Before using the TV, follow the steps below to learn how to navigate the menu in order to select and adjust different functions.

1. Press the MENU button. The main menu is displayed on the screen. Its left side has the following icons: Picture,

Sound, Channel, Setup, Input, Support.

2. Press the ▲ or ▼ button to select one of the icons.

Press the ◄ or ► button to access the icon’s sub-menu.

3. Press the ▲ or ▼ button to move to items in the menu.

Press the ENTER

button to enter items in the menu.

4. Press the ▲/▼/◄/► button to change the selected items.

Press the RETURN button to return to the previous menu.

5. Press the EXIT button to exit from the menu.

Using the remote control buttons

Button Operations Button Operations

RETURN

EXIT

Display the main on-screen menu. ▲/▼/◄/►/

Return to the previous menu.

Exit the on-screen menu.

ENTER

Example: Setting the TV’s Brightness in the Picture Menu

Adjusting the Brightness to 80



1. Press the MENU button to display the menu.

2. Press the ENTERE button to select Picture.

3. Press the ▲ or ▼ button to select Brightness.

4. Press the ENTERE button.

5. Press the ◄ or ► button until the Brightness changes to 80.

6. Press the ENTERE button.

Press the EXIT button to exit from the menu.

Picture

Mode : Standard

Backlight : 8

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Move the cursor and select an item. Select the currently selected item.

Conrm the setting.

Picture

Mode : Standard

Backlight : 8

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Picture

Mode   :Standard ►

Backlight : 8

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Backlight : 8

Picture

Contrast : 95

Brightness  :45  ►

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Advanced Settings

Picture Option

Picture Reset

Brightness 45

Move L Adjust E Enter R Return

Brightness 80

Move L Adjust E Enter R Return

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.

1. Press the POWER P button on the remote control.

You can also use the POWER

The message Menu Language, Store Demo, Channels, and Time will be set. is

button on the TV.

displayed.

Menu Language, Store Demo, Channels, and Time will be set.

Plug & Play

Start

Enter

2. Press the ENTERE button, then Sets the menu language. menu is automatically displayed.

3. Press the ▲ or ▼ button to select the language, then press the ENTERE button. The message Select ‘Home Use’ when installing this TV in your home. is displayed.

4. Press the ◄ or ► button to select Store Demo or Home Use, then press the ENTERE button. The message Select the Antenna source to memorize. is displayed.

We recommend setting the TV to Home Use mode for the best picture in your home environment.

Store Demo mode is only intended for use in retail environments. If the unit is accidentally set to Store Demo mode and you want to return to Home Use (Standard): Press the volume button on the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.

5. Press the ▲ or ▼ button to memorize the channels of the selected connection. Press the ENTERE button to select Start.

Air: Air antenna signal. / Cable: Cable antenna signal. / Auto: Air and Cable antenna signals.

In Cable mode, you can select the correct signal source among STD, HRC, and IRC by pressing the ▲, ▼, ◄ or ► button, then press the ENTER

button. If you have Digital cable, select the cable system signal source for both Analog

and Digital. Contact your local cable company to identify the type of cable system that exists in your particular area.

6. Press the ENTERE button to select Start. The TV will begin memorizing all of the available channels.

To stop the search before it has nished, press the ENTER

After all the available channels are stored, it starts to remove scrambled channels. The Auto program menu then reappears. Press the ENTER

button when channel memorization is complete. The message Set the Clock Mode. is

button with Stop selected.

displayed.

7. Press the ENTERE button. Press the ▲ or ▼ button to select Auto, then Press the ENTER

button. The message Set to daylight saving time. is

displayed. If you select Manual, Set current date and time is displayed.

8. Press the ▲ or ▼ button to select Off, On or Auto, then press the ENTERE button.

9. Press the ▲ or ▼ button to highlight the time zone for your local area. Press the ENTERE button. If you have received a

digital signal, the time will be set automatically. If not, see page 30 to set the clock.

10. The connection method to provide the best quality HD is offered. After conrming the method, press the ENTERE button.

11. The message Enjoy your watching. is displayed. When you have nished, press the ENTERE button.

If you want to reset this feature...

1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTERE button.

2. Press the ENTERE button again to select Plug & Play.

The Plug & Play feature is only available in the TV mode.

English - 22

English - 23

CHANNEL CONTROL

ConguringtheChannelMenu

Antenna→Air/Cable

❑

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an Air or a Cable system).

Press the TOOLS button to display the Tools menu. You can also set the Antenna by

selecting

Auto Program

❑

Air: Air antenna signal. / Cable: Cable antenna signal. / Auto: Air and Cable antenna



Tools→SwitchtoCable (or Switch to Air).

signals

When selecting the Cable TV system: Selects the cable system. STD, HRC and IRC

identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected.

After all the available channels are stored, it starts to remove scrambled channels (Clear Scrambled Channels). The Auto

program menu then reappears. If you want to stop Auto Programming, press the ENTER

button. The Stop Auto Program? message will be displayed.

Select Yes by pressing the ◄ or ► button, then press the ENTERE button.

Clear Scrambled Channels (digital channels only)

❑

This function is used to lter out scrambled channels after Auto Program is completed. This process may take up to 20~30 minutes.

To stop searching scrambled channels: Press the ENTER

button to select Stop. Press the ◄ button to select Yes, then

press the ENTERE button. This function is only available in Cable mode.

Channel

Antenna  :Air  ►

Auto Program

Clear Scrambled Channel

Channel List

Fine Tune

Channel List

❑

For detailed procedures on using the Channel List, refer to the ‘Managing Channels’ instructions.

You can select these options by simply pressing the CH LIST button on the remote control.

Fine Tune (analog channels only)

❑

Use ne tuning to manually adjust a particular channel for optimal reception.

If you do not store the ne-tuned channel in memory, adjustments are not saved.

* will appear next to the name of ne-tuned channels.

To reset the ne tuning setting, press the ▼ button to select Reset, then press the ENTER

Managing Channels

Using this menu, you can add / delete or set favorite channels and use the program guide for digital broadcasts.



All Channels

Shows all currently available channels.



Added Channels

Shows all added channels.



Favorite

Shows all favorite channels.

To select the favorite channels you have set up, press the FAV.CH button on the remote control.

button.

Added Channels

Air

2 Air

4 Air

4-2 ♥ TV #8

8 Air

13 Air

13-1 ♥ TV #3

Alice’s Adventures in Wonderland

Zoom Select T Tools

Programmed



Shows all current reserved Programs.

Select a channel in the All Channels, Added Channels or Favorite screen by pressing the ▲ / ▼ buttons, and pressing the

ENTER

button. Then you can watch the selected channel.

Using the Color buttons with the Channel List

Green (Zoom): Enlarges or shrinks a channel number.

–

Yellow (Select): Selects multiple channel lists. You can perform the add / delete or add to Favorite / delete from Favorite

–

function for multiple channels at the same time. Select the required channels and press the yellow button to set all the selected channels at the same time. The

–

TOOLS (Tools): Displays the Add (or Delete), Add to Favorite (or Delete from Favorite), Timer Viewing, Channel

mark appears to the left of the selected channels.

Name Edit, Select All (or Deselect All) and Auto Program menus (The Options menus may differ depending on the situation.)

Channel Status Display Icons

–

♥ : A channel set as a Favorite.

–

: A channel selected by pressing the yellow button.

–

(

: A Program currently being broadcast.

–

)

: A reserved program

Channel List Option Menu (in All Channels / Added Channels / Favorite)

Press the TOOLS button to use the option menu.

Option menu items may differ depending on the channel status.

Add / Delete



You can delete or add a channel to display the channels you want.

All deleted channels will be shown on All Channels menu.

A gray-colored channel indicates the channel has been deleted.

The Add menu only appears for deleted channels.

You can also delete a channel from the Added Channels or Favorite menu in the same

manner.

Add to Favorite / Delete from Favorite



You can set channels you watch frequently as Favorite.

Press the TOOLS button to display the Tools menu. You can also set the add to (or delete from) Favorites by selecting Tools

→AddtoFavorite (or Delete from Favorite). The ♥ symbol will be displayed and the channel will be set as a favorite.

All favorite channels will be shown in the Favorite menu.

Timer Viewing



If you reserve a program you want to watch, the channel is automatically switched to the reserved channel in the Channel List;

even when you are watching another channel. To reserve a program, set the current time rst. (See page 30)

Only memorized channels can be reserved.

You can set the channel, month, day, year, hour and minute directly by pressing the number buttons on the remote control.

Reserving a program will be shown in the Programmed menu.

Digital Program Guide and Viewing Reservation

When a digital channel is selected, and you press the ► button, the Program Guide for the channel appears.

a program according to the procedures described above.



Channel Name Edit (analog channels only)

Channels can labeled so that their call letters appear whenever the channel is selected.

The names of digital broadcasting channels are automatically assigned and cannot be labeled.



Select All / Deselect All

●

Select All: You can select all the channels in the channel list.

●

Deselect All: You can deselect all the selected channels.

You can only select Deselect All when there is a selected channel.

Auto Program



For further details on setting up options, refer to page 23.

All Channels

Air

2 Air

4 Air

4-2 ♥ TV #8

8 Air

13 Air

13-1 ♥ TV #3

Alice’s Adventures in Wonderland

Zoom Select T Tools

You can reserve

Delete

Add to Favorite

Timer Viewing

Channel Name Edit

Select All

Auto Program

English - 24

English - 25

Channel List Option Menu (in Programmed)

You can view, modify or delete a reservation.

Press the TOOLS button to use the option menu.

Change Info



Select to change a viewing reservation.

Cancel Schedules



Select to cancel a viewing reservation.

Information



Select to view a viewing reservation. (You can also change the reservation information.)

Select All



Select all reserved Programs.

PICTURE CONTROL

ConguringthePictureMenu

Mode

❑

You can select the type of picture which best corresponds to your viewing requirements.

Press the TOOLS button to display the Tools menu. You can also set the picture mode by

selecting



Dynamic

Selects the picture for increased denition in a bright room.



Standard

Selects the picture for the optimum display in a normal environment.



Movie

Selects the picture for viewing movies in a dark room.

Tools→PictureMode.

Programmed

1 / 1 / 2009

9:08 am 5 TV1 Quincy, M.E

3:15 pm 2 TV3 The Equalizer

5:50 pm 2 TV3 McMillan & Wife

Zoom Select

Picture

Mode  :Standard  ►

Backlight : 8

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Change Info

Cancel Schedules

Information

Select All

Tools E Information

Backlight / Contrast / Brightness / Sharpness / Color / Tint (G/R)

❑

Your television has several setting options that allow you to control the picture quality.

Backlight: Adjusts the brightness of LCD back light.

●

Contrast: Adjusts the contrast level of the picture.

●

Brightness: Adjusts the brightness level of the picture

● Sharpness: Adjusts the edge denition of the picture.

●

Color: Adjusts color saturation of the picture.

●

Tint (G/R): Adjusts the color tint of the picture.

●

When you make changes to Backlight, Contrast, Brightness, Sharpness, Color or Tint (G/R) the OSD will be adjusted

accordingly. In PC mode, you can only make changes to Backlight, Contrast and Brightness.

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

The energy consumed during use can be signicantly reduced if the brightness level of the picture is lowered, which will

reduce the overall running cost.

Advanced Settings

❑

Samsung’s new TVs allow you to make even more precise picture settings than previous models.

Advanced Settings is available in Standard or Movie mode.

In PC mode, you can only make changes to Gamma and White Balance from among the

Advanced Settings items.

BlackTone→Off/Dark/Darker/Darkest



You can select the black level on the screen to adjust the screen depth.

Advanced Settings

Black Tone : Off ►

Dynamic Contrast : Medium Gamma : 0 Color Space : Native White balance Flesh Tone : 0 Edge Enhancement : On

Move E Enter R Return

DynamicContrast→Off/Low/Medium/High



You can adjust the screen contrast so that the optimal contrast is provided.

Gamma



You can adjust the primary color (red, green, blue) Intensity. (-3 ~ +3)

Color Space



Color space is a color matrix composed of red, green and blue colors. Select your favorite color space to experience the most natural color.

Native: Native Color Space offers deep and rich color tone.

●

Auto: Auto Color Space automatically adjusts to the most natural color tone based on program sources.

●

White Balance



You can adjust the color temperature for more natural picture colors.

R-Offset / G-Offset / B-Offset / R-Gain / G-Gain / B-Gain: You can adjust the Color ‘temperature’ in the light areas by

●

changing the values of R, G, B. Recommended for advanced users only. Reset: The previously adjusted white balance will be reset to the factory defaults.

●

Changing the adjustment value will refresh the adjusted screen.

Flesh Tone



You can emphasize the pink ‘esh tone’ in the picture.

Changing the adjustment value will refresh the adjusted screen.

EdgeEnhancement→Off/On



You can emphasize object boundaries in the picture.

Picture Options

❑

In PC mode, you can only make changes to the Color Tone and Size from among the

items in Picture Options.

ColorTone→Cool/Normal/Warm1/Warm2



Warm1 or Warm2 is only activated when the picture mode is Movie.

Settings can be adjusted and stored for each external device you have connected to an

Picture Options

Color Tone : Normal ►

Size : 16:9 Digital NR : Auto

HDMI Black Level : Normal

Film Mode : Off

input of the TV.

Size



Move E Enter R Return

Occasionally, you may want to change the size of the image on your screen. Your TV comes with six screen size options, each

designed to work best with specic types of video input. Your cable box/satellite receiver may have its own set of screen sizes as

well. In general, though, you should view the TV in 16:9 mode as much as possible.

Alternately, you can press the P.SIZE button on the remote control repeatedly to change the picture size.

16:9 : Sets the picture to 16:9 wide mode.

● Zoom1: Magnies the size of the picture on the screen.

● Zoom2: Magnies the size of the picture more than Zoom1.

● Wide Fit: Enlarges the aspect ratio of the picture to t the entire screen.

●

4:3 : Sets the picture to 4:3 normal mode.

●

Screen Fit: Use the function to see the full image without any cutoff when HDMI (720p/1080i), Component (1080i) or DTV

●

(1080i) signals are input.

16:9

Zoom1 U Move Zoom2 U Move

16:9 Zoom1 Zoom2

Wide Fit U Move

4:3 Screen Fit

Wide Fit 4:3 Screen Fit

English - 26

+ 65 hidden pages