Samsung Electronics
LED Display
Installation Manual
LH008IWJ*** (P0.84)
LH012IWJ*** (P1.26)
LH016IWJ*** (P1.68)
SNOW-1810U
Ver. 2.0 (2020.03.20)
Revision History
Samsung Electronics
Version |
Date (Y/M/D) |
Description |
|
|
|
2.0 |
2020/03/20 |
New Release |
|
|
|
|
|
|
1
Dehumidification guidance – during installation Samsung Electronics
When humidity get into LED package because of high humidity, it is possible to cause ‘Line defect’ by electrical short in side of LED
Package.
For keeping quality of products during installation, please refer below cautions.
-If one of below case meet before installation, MUST do dehumidification process.
∙Case when vacuum packaging is broken before unpacking.
∙Case when environment condition is exceed Samsung recommended operation condition. (Please refer Operation condition from User manual)
∙Case when period between unpacking and turning on the power of products is spent more than 7days, even though it is under Samsung recommended storage condition.
∙Case when production date on the label is exceed more than 6 months, even though vacuum packaging is no problem.
-When Volatile chemicals such as oil paint, solvent are used or operation condition is exceed around of products installed place, MUST play video more than 2 hours everyday.
-If it is not meet with upper cases, it is helpful to play video more than 2 hours everyday for protection for humidity getting into LED Package.
Dehumidification guidance – during operation Samsung Electronics
Electrical short in package is possible to happen during products are working.
For keeping quality of products during installation, please refer below cautions.
-If one of below case meet during operation, MUST do dehumidification process.
∙Case when environment condition is exceed operation condition.
∙Case when products are not working more than 1 month, even though environment condition is under operation condition.
-When environment condition is exceed operation condition, products are out of warranty. Please check environment condition.
-Even products are operating, if the installed place have extra construction such as interior modification, MUST do dehumidification following installation condition.
-It is possible to happen dew condensation on surface of products, even though working on operating condition. When happening dew condensation, MUST operate after cleaning the dew condensation & dehumidification.
Dew condensation due to overcooling
Samsung Electronics
Even though meet with Samsung recommended operation condition, dew condensation is possible to happen when surface of products is colder than environment temperature or
hot & humid air blow to cooled surface of products.
(cf : Principle of happening dew on surface of glass which have ice)
Case when dew condensation is happen on products, it is possible to be the root of defect. In this case, it is possible to be out of warranty.
Guidance of latest firmware
Samsung Electronics
When install products, please update latest firmware on online
-You can download latest firmware from SLM site.
∙URL of SLM Page : https://www.secslm.com
∙After login Help Download Center Download
∙Before you download firmware, you MUST check same firmware of model (marked red letter in below) & upper number of version (marked blue in below).
Cabinet : Main - L-xxxMWWAC-nnnn.n |
xxx = Pan name, nnnn.n = version |
FPGA - aabbb_ddddd |
aa = pixel pitch, bbb = LED package type, ddddd= version |
Example : IER P2.5 Cabinet : L-IERMWWAC-1003.1, FPGA : 25252-31046
S-box : TB-KTM2SBMDWWC_100x.x
-You can update firmware through LSM.
∙ Please refer ‘7-1 PC control program’ for the way to update firmware.
5
Check first before Installation (1/2)
Samsung Electronics
•All Power cables and OCM cable must be connected firmly
•For HDBT signal stability, use the cable above CAT6 *STP, *FTP level. ( Length 15m~100m )
- Do not use “comb” or “pinstripe” cable.
“CAT6 UTP can not be allowed”
•Do not mix cabinet which have different Project number, each cabinet have its own project number.
Module |
|
Cabinet |
|
Box |
|
|
|
|
|
6
Check first before Installation (2/2)
Samsung Electronics
•Install the device only using SNOW-1810U and its supplied IG.
Please check below Cabinet and S-box compatibility table information
S-Box |
SNOW-1810U |
SNOW-1703ULD |
SNOW-1703U |
|
|
|
|
I/G |
BN91-20525A |
BN91-19993A |
BN91-19100A |
|
|
|
|
Cabinet |
IF015H, |
IF015H, |
IF015H, |
|
IF020H, |
IF020H, |
IF020H, |
|
IF025H, |
IF025H, |
IF025H, |
|
IF025H-D, |
IF025H-D, |
IF025H-D, |
|
IF040H-D, |
IF040H-D, |
IF040H-D, |
|
IF060H-D, |
IF060H-D, |
IF060H-D |
|
IF012J, |
IF012J |
|
|
IW008J |
|
|
|
IW012J |
|
|
|
IW016J |
|
|
|
|
|
|
7
Table of Contents
Samsung Electronics
1.Product Information and Precautions for Installation ( 4 page )
2. |
Check Point about the Radiant Heat |
( 9 page ) |
|
3. |
Preparation for Cabinet Installation |
( 15 page ) |
|
4. |
Frame Installation |
( 22 page ) |
|
5. |
Cabinet + Frame Installation |
( 30 page ) |
|
6. |
Disassembly & Front Service |
( 41 page ) |
|
7. |
Cable Connection |
( 58 page ) |
|
8. |
S-BOX Installation and Connection |
( 71 page ) |
|
9. |
LSM Settings and How to Use |
( 88 page ) |
|
10. |
Issue and Solution |
( 103 page ) |
|
11. |
Color Calibration |
( 104 page ) |
|
12. |
Bezel Installation |
( 107 page ) |
|
13. |
Annex |
( 115 page ) |
8 |
|
|
|
1. Product Information and Precautions for Installation
Samsung Electronics
Cabinet Infomation
|
|
IW008J (P0.84) |
IW012J (P1.26) |
IW016J (P1.68) |
|
|
|
|
|
|
|
|
Pitch |
0.84 mm |
1.26 mm |
1.68 mm |
|
Basic Spec. |
|
|
|
|
|
|
Cabinet Resolution |
960 X 540 |
640 X 360 |
480 X 270 |
|
|
|
|
|
|
|
|
Brightness (Max) |
1600-nit/500-nit |
1600-nit/800-nit |
1400-nit/1000-nit |
|
|
|
|
|
|
|
|
Contrast Ratio |
|
10,000:1 |
|
|
Color Spec. |
|
|
|
|
|
Viewing angle (H/V) |
145°/155° |
140°/160° |
135°/155° |
||
|
|||||
|
|
|
|
|
|
|
Refresh rate |
|
1920 Hz ~ 3840 Hz |
|
|
|
|
|
|
|
|
|
Input Power |
|
100~240 VAC, 50/60 Hz |
|
|
Power Spec. |
|
|
|
|
|
Power consumption (Max) |
190 (W/Cabinet) |
192 (W/Cabinet) |
180 (W/Cabinet) |
||
|
|||||
|
|
|
|
|
|
|
Working Temperature |
|
0 ~+40 /10~80%RH |
|
|
Operation |
|
|
|
|
|
IP Rating |
|
IP20 |
|
||
Spec. |
|
|
|
|
|
Power Daisy Chain (220V / 110V) |
|
4sets / 3sets |
|
||
|
|
|
|||
|
|
|
|
|
|
Certification |
Safety |
|
60950-1 |
|
|
|
|
|
|
||
Spec. |
EMC |
|
Class B |
|
|
|
|
|
|||
|
|
|
|
|
9
1. Product Information and Precautions for Installation |
Samsung Electronics |
|||||||||||
Screen configuration by model (Pitch) (Refer to page 22 for frame kit) |
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Specification |
|
|
IWJ |
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|||
|
|
P0.84 |
P1.26 |
|
P1.68 |
|
||||||
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Cabinet Size |
806.4 x 453.6 x 72.2 |
806.4 x 453.6 x 72.2 |
|
806.4 x 453.6 x 72.8 |
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Cabinet |
|
Module Size |
|
|
201.6 mm x 151.2 mm |
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Weight |
12.5kg |
12.2kg |
|
12.5kg |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Cabinet Q’ty |
2x2 (4set) |
|
3x3 (9set) |
|
|
4x4 (16set) |
|
|
|
|
|
|
I/G Q’ty |
1 |
|
1 |
|
|
1 |
|
|
|
|
FHD |
|
Size |
1612.8mm X 907.2mm |
|
2419.2mm X 1360.8mm |
|
|
3225.6mm X 1814.4mm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Frame Kit |
VG-LFJ08FWW |
|
VG-LFJ08TWW |
|
|
VG-LFJ08UWW |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Screen |
|
|
Bezel |
IWJPA-WP008D2X2 |
|
IWJPA-WP008D3X3 |
|
|
IWJPA-WP008D4X4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Cabinet Q’ty |
4x4 (16set) |
|
6x6 (36set) |
|
|
8x8 (64set) |
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
I/G Q’ty |
4 |
|
4 |
|
|
4 |
|
|
|
|
UHD |
|
Size |
3225.6mm X 1814.4mm |
|
4838.4mm X 2721.6mm |
|
|
6451.2mm X 3628.8mm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Frame Kit |
VG-LFJ08UWW |
|
VG-LFJ08TWW x4 |
|
x4 |
VG-LFJ08UWW x4 |
x4 |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
Bezel |
IWJPA-WP008D4X4 |
|
IWJPA-WP008D3X3 |
|
IWJPA-WP008D4X4 |
|||
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
Cabinet Product Information |
SBB-SNOWJAU (S-Box, I/G) |
|
(S-Box) |
(I/G x4ea) |
|
|
|
|
|
Interface Gender |
10 |
|
|
1. Product Information and Precautions for Installation
Samsung Electronics
• Precautions for Installation (LED damage)
Caution |
Image |
|
[ Beware of Outside Impact, Fall] |
|
|
Beware not to cause any impact on the LED screen or drop the product on the floor |
MODULE |
|
after the protection gets taken off for installation. |
Front |
|
|
||
Beware not to put the LED side headed downwards to the floor after the protection |
|
|
gets taken off for installation. |
|
|
Beware not to have the corner area of LED module be damaged due to the contact |
||
|
||
with the outside. |
|
|
Beware not to put more than 12 layers. |
|
|
[Beware of LED Damage due to Static Electricity] |
|
|
Beware not to touch LED screen with bare hands without putting gloves on. |
|
|
[Beware of LED & Film Damage due to Metallic Substances] |
|
|
Beware not to have metallic substances pulled in to the surface |
|
|
due to the magnetic force on the front side of the LED. |
LED & |
|
Film |
||
If any metallic substances get drawn in on the surface, please disassemble the |
|
|
module and then remove the pollutants by using a magnet. |
|
|
[Beware of LED Damage due to chemicals.] |
|
|
Beware not to contact water, waxes, benzene, thinners, mosquito repellents, |
|
|
lubricants, cleaners, solvents or surfactants on LED. |
|
|
When installing on the construction site, it should be installed after construction & cleaning. |
|
|
If the installation site requires construction work, the product is covered with a |
|
|
curtain and operated 50% white or video for 2 hours every day. |
11 |
1.Product Information and Precautions for Installation Samsung Electronics
Caution for cleaning screen
-It is recommended to wipe with a soft cleaning cloth provided with the product. If there is a contamination area that is not removed well, a small amount of glass detergent of the surfactant component is sprayed on the cleaning cloth provided. (However, do not spray the glass detergent directly on the screen)
-Hard stuff on screen surface can damage LED chip and film during cleaning.
Clear screen surface before cleaning
Caution
-Watch out for damage when cleaning gap between HalfCabinets
-Watch out for damage when cleaning gap between Modules
-Do not insert any cleaning tool or spay cleaner directly into the gap
-Do not wipe the LED surface with hard materials such as paper towels, brushes comb or brush, acrylic or steel.
-Do not use chemicals such as wax, benzene, cinna, mosquito repellent, air freshener, lubricant, and detergent in products
12
1. Product Information and Precautions for Installation
Samsung Electronics
• Preparations for Installation
(-) (+) driver
•Provided in Frame Kit. (BN96-48298A)
M3, L6
SCREW-MACHINE
Cover-PCB |
M4, L6 |
|
HOLDER-SCREW |
||
(BN63-18008A) |
||
(BN61-16452B) |
||
|
||
|
Packed in a small zipper bag |
•Provided in accessory kit. (CY-WJJPWP).
PROTECTION |
EDGE PROTECTION V/H |
MAGNET JIG |
GAP-TOOL |
|
(BN81-17111A) |
(BN81-17514A/BN81-17515A) |
(BN81-17114A) |
||
(BN81-17113A) |
||||
|
|
|
Adjustment tool |
PLIER |
Absorber |
Glove |
(BN81-17112A) |
(BN81-17541A) |
(BN81-17124A) x4 |
(RA00400E-002539) |
•Provided in Frame Kit. (VG-LFJ08*WW).
Hex Wrench
2mm, 6mm
13
2. Check Point about the Radiant Heat
Samsung Electronics
|
Standard and condition for indoor installation |
Written under ‘Full white, (back light 7)’ standard |
|
|
Written under ‘Video, (back light 10)’ standard |
- |
Standard for using ‘SAMSUNG WALL MOUNT’ (Fulfill ADA) ADA(American’s with Disabilities Act |
|
- |
Ceiling installation, outdoor installation, cannot be installed where there is vibration |
|
|
|
98.6mm |
|
It is not possible to install it in a special case, and it is necessary to consult technical sales |
|
|
separately. |
|
|
|
Measuring |
- |
In principle, solar window direct radiation condition installation is avoided. |
location for |
|
|
ambient |
- |
Window side, adjacent installation |
temperature |
. A weak solar scan of the time zone except for the noon time zone during work is allowed
. If surface temperature rise is minor (1 ~ 2 degrees) allowed temperature
. Use UV blocking / light blocking film when installation of window adjacent is inevitable.26.1mm
-Room temperature is recommended to be 0 ~ 25
-Effect of Cold / Hot Wind on Air Conditioning System
. If the cold or hot air is the same air conditioning system, be careful not to affect the product. - Air temperature measurement position
. Based on product center or air let part
<![endif]>wall
14
2. Check Point about the Radiant Heat– without Fan
Samsung Electronics
Minimum spacing for buried installation
At least 60mm installation space required for upper, lower, left, and right
All interior finishes proceed after screen installation
Recommended condition : Min 500mm (set ~ ceiling)
Min 100mm when maintaining the indoor temperature below Min 60mm
25 degrees due to air conditioning operation
|
|
|
|
|
|
Min 60mm |
|
|
|
|
|
|
|
Air vent area |
|
||
|
|
|
|
|
|
|
|
|
Must use mesh with an opening rate of 60% or more |
|
|
|
|
|
|
|
|
<![endif]>WALL
Min 60mm
Min 100mm (set ~ floor)
Air vent area
Must use mesh with an opening rate of 60% or more
Min 60mm
Vent and interior finishing work will proceed after screen installation 10
2. Check Point about the Radiant Heat– without Fan
Samsung Electronics
Minimum spacing for buried installation
Recommended condition : Min 500mm (set ~ ceiling)
Min 100mm when maintaining the indoor temperature below 25 degrees due to air conditioning operation
<![if ! IE]><![endif]>WALL
Min 100mm (set ~ floor)
11
2. Check Point about the Radiant Heat– with Fan
Samsung Electronics
Example of minimum spacing and placement during landfill installation
Recommended condition : Min 500mm (set ~ ceiling)
Min 100mm when maintaining the indoor temperature below 25 degrees due to air conditioning operation
Min 60mm |
|
|
|
|
|
Excluding FAN |
|
|
|
|
|
|
Air vent area must use mesh with |
|
|
|
|
should be sealed |
|
|
an opening rate of 60% or more |
|
|
|
|
|
|
|
|
||
|
|
|
|
<![if ! IE]> <![endif]>WALL |
|
left and right sealing |
|
|
|
Air vent area
Must use mesh with an opening rate of 60% or more
Min 60mm
Min 100mm (set ~ floor) |
Min 60mm |
Vent and interior finishing work will proceed after screen installation 12
2. Check Point about the Radiant Heat– with Fan
Samsung Electronics
Example of minimum spacing and placement when installing walls
Recommended condition : Min 500mm (set ~ ceiling)
Min 100mm when maintaining the indoor temperature below 25 degrees due to air conditioning operation
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Air vent area must use mesh with an |
|
Excluding FAN |
|
|
|
|
|
opening rate of 60% or more |
|
should be sealed |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
<![endif]>WALL
Min 100mm (set ~ floor)
Vent and interior finishing work will proceed after screen installation 13
2. Check Point about the Radiant Heat– with Fan
Samsung Electronics
Example of minimum spacing and placement during rear exhaust
Recommended condition : Min 500mm (set ~ ceiling)
Min 100mm when maintaining the indoor temperature below 25 degrees due to air conditioning operation
The SCREEN wall is managed below 30 on the back of the wall.
Excluding FAN should be sealed
<![if ! IE]><![endif]>WALL
left and right sealing
Air vent area
Must use mesh with an opening
rate of 60% or more
Min 60mm
Min 100mm (set ~ floor)
Vent and interior finishing work will proceed after screen installation 14
3. Preparation for Cabinet Installation |
Samsung Electronics |
•Preparations Before Installation
Remove the Box tape at the upper area and then open up the box. (Fig.2)
Remove the Top–Cushion and hold the handle inside PE-Bag and pull out the set then remove PE bag.
(Fig.2)
Check whether there is any abnormality on the screen by connecting the power cable.(Fig.3)
Process of Screen check (Page.21)
HANDLE
CUSHION-TOP
SWITCH
LED-SET
CUSHION-BOTTOM
Al-Bag
BOX
Fig.1 Packing & Product |
Fig. 2 Remove Al-Bag |
Fig.3 Check the Screen |
20
3. Preparation for Cabinet Installation
Samsung Electronics
18ea Holder-PCB fixing screws and 4 Cover-PCB fixing screws are released.
Remove the filament tape attached to the top / bottom / left / right.
Fig.4 Holder-PCB & Cover-PCB & Protective Sheet Removal
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HOLDER-PCB |
COVER-PCB |
|
Filament Tape |
|
|
X18 SCREW-MACHINE (6003-000133, M4,L8) |
Remove Cover-PCB and screws and keep them separately. |
|
It is required when working on the back. |
|
The Cover-PCB, Screw, and Bolt are included in the accessory of the Cabinet |
X4 SCREW-MACHINE (6003-001501, M3,L6) |
|
21
3. Preparation for Cabinet Installation
Samsung Electronics
Unfasten the 4 screws on the Cover Corner area to separate those screws and
Remove the protective sheet attached to the two sides (Top/Bottom). (Fig.4)
X4 SCREW-MACHINE (6003-000133, M4L8)
SCREW
Fig.4 Cover Corner Removal
22
3. Preparation for Cabinet Installation
Samsung Electronics
- Using Spacer-PET
When Black Seam occurs, remove the Spacer-PET of the point.
Spacer-PET should not protrude more than module
If necessary, attach Spacer-PET. (Fig.5)
Check the gap between the module and the Bracket-Sub using a gap gauge.
If the step is 0.06mm or more, attach Spacer-PET (0.05t / 0.1t).
Spacer-PET :
-In order to minimize the load applied to the module during large size installation,
Attach it to the Bracket-Sub to minimize the gap between the module and the Bracket-Sub.
- Cabinet 8poiont attached to Spacer-PET
Using Gap gauge
Step compensation by attaching Gap-
Sheet
Fig.5 Check the difference between the module and B / SUB
23
3. Preparation for Cabinet Installation
Samsung Electronics
Dehumidification
In order to protect LED devices, the following items must be dehumidified.
[Dehumidification when Installed]
-If it is installed after more than 6 months in vacuum-packed condition after factory shipment.
-Storage for more than one week should be performed without vacuum treatment.
[Dehumidification during Use]
-Dehumidification is performed in an environment of 40 / 80% or less for 30 days or more. (Refer to LSM dehumidification, page 102page)
How to dehumidify before installation
-Press the button for 3 seconds after the cabinet is turned on.
When the initial AC power is turned on, time required for operation of AM3352 IC is required.
Wait about 30 seconds and let it go.
When the button is released, Dehumidifying Mode is executed. (Display the module at the top left)
- Aging with 24 hours on.
SWITCH
Aging 24 hours
3
Caution
♦The normal installation mode of operating IWJ (LH008IWJMWS, LH012IWJMWS, LH016IWJMWS) is “ STB ” mode (switch).
Please use "O" mode only for cabinet landing inspection and change it to "STB" mode after inspection. |
|
♦ The switch that performs the factory dehumidification mode and factory reset function is the same. If you press 3 seconds, you enter |
24 |
dehumidification mode. If you press 10 seconds or more, the factory reset is performed. |
3. Preparation for Cabinet Installation
Samsung Electronics
Process of Dehumidification
- The Dehumidification process progresses automatically for 24 hours as the brightness increases gradually.
Step |
condition |
Brightness |
Time |
1 |
Lighting up display with 10 gray scale |
5% |
2 hr |
|
|
|
|
2 |
Lighting up display with 20 gray scale |
8% |
2 hr |
|
|
|
|
3 |
Lighting up display with 30 gray scale |
10% |
2 hr |
|
|
|
|
4 |
Lighting up display with 40 gray scale |
15% |
2 hr |
|
|
|
|
5 |
Lighting up display with 50 gray scale |
20% |
2 hr |
|
|
|
|
6 |
Lighting up display with 70 gray scale |
25% |
2 hr |
|
|
|
|
7 |
Lighting up display with 90 gray scale |
35% |
2 hr |
|
|
|
|
8 |
Lighting up display with 120 gray scale |
45% |
2 hr |
|
|
|
|
9 |
Lighting up display with 150 gray scale |
60% |
2 hr |
|
|
|
|
10 |
Lighting up display with 180 gray scale |
70% |
2 hr |
|
|
|
|
11 |
Lighting up display with 200 gray scale |
80% |
2 hr |
|
|
|
|
12 |
Lighting up display with 255 gray scale |
100% |
2 hr |
|
|
|
|
3. Preparation for Cabinet Installation
Samsung Electronics
Reference : Process of Screen check
TOGGLE SWITCH
SWITCH |
POWER INLET |
|
|
|
POWER OUTLET |
|
TOGGLE SWITCH |
Check the picture of the screen
Internal white pattern
1.After turn on power, press the toggle switch button for five seconds
2.Dehumidification screen comes out, push the toggle switch twice
3.when the white screen is displayed, check the defective LED by sequentially pressing toggle switch * Do not turn on the white pattern over 10 seconds before dehumidification
4.if you need more brighter pattern, push ‘toggle switch’ button for three(3) seconds in white pattern
5.push toggle switch for three(3) seconds again to exit factory OSD
26
4. Frame Installation
Samsung Electronics
Frame Kit Composition.
VG-LFJ08SWW VG-LFJ08FWW VG-LFJ08TWW VG-LFJ08UWW
No |
Item |
1x1 |
2x2 |
3x3 |
4x4 |
|
|
|
|
|
|
|
|
|
|
|
Units |
Units |
Units |
Units |
|
|
|
|
|
|
|
|
BRACKET H (horizontal) |
2 |
2 |
2 |
6 |
|
|
|
|
|
|
|
|
|
BRACKET SIDE (vertical) |
2 |
2 |
2 |
2 |
|
|
|
|
|
|
|
|
|
BRACKET MIDDLE (vertical) |
- |
2 |
3 |
4 |
|
|
|
|
|
|
|
|
|
JOINT H |
2 |
2 |
2 |
3 |
|
|
|
|
|
|
|
|
|
JOINT V |
2 |
4 |
6 |
8 |
|
|
|
|
|
|
|
|
|
BRACKET JIG |
1 |
1 |
1 |
1 |
|
|
|
|
|
|
|
|
|
LEVELER |
- |
2 |
2 |
2 |
|
|
|
|
|
|
|
|
|
SCREW |
4 |
6 |
6 |
15 |
|
|
|
|
|
|
|
|
|
Anchor |
4 |
6 |
6 |
15 |
|
|
||||||
|
|
|
|
|
|
|
|
DRY WALL SCREW |
4 |
6 |
6 |
15 |
|
|
||||||
|
|
|
|
|
|
|
|
MANUAL-INSTALL |
1 |
1 |
1 |
1 |
|
|
||||||
|
|
|
|
|
|
|
|
ALIGN JIG |
- |
- |
1 |
1 |
|
|
||||||
|
|
|
|
|
|
|
|
LEVEL |
- |
1 |
1 |
2 |
|
|
||||||
|
|
|
|
|
|
|
|
HOLDER PCB |
15 |
30 |
45 |
60 |
|
|
||||||
|
|
|
|
|||
Installation Screen Size (mm) |
806.4x453.6 |
1612.8x907.2 |
2419.2*1360.8 3225.6*1814.4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
M5,L65
|
|
|
27
4. Frame Installation
Samsung Electronics
Assemble Bracket Side/Middle with Bracket H.
-First insert Bracket H to assembled Joint H and Bracket H. (Fig.1)
-Second put 3 groups of Bracket H on ground. And insert Bracket Side/Middle to Bracket H. (Fig.2)
. Bracket Side used at side position, Bracket Middle used at middle position.
-Then fasten up the screws. (Fig.3)
|
|
|
|
|
|
|
|
|
|
|
, |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
M6L8 |
M4L8 |
Fig.1 Insert Bracket H |
Fig.2 Insert Bracket V to Bracket H |
|
Fig.3 Fix Bracket with screw |
28 |
4. Frame Installation
Samsung Electronics
Assemble Leveler on the Bracket Side at required height position.
- Put Leveler on Bracket side at required height position with moving up and down. (Fig.1)
M4L8 Screw
Fig.1 Assemble Leveler
29