Samsung SNOW-1810U, LH008IWJ, LH012IWJ, LH016IWJ Installation Manual

Samsung Electronics

LED Display

Installation Manual

LH008IWJ*** (P0.84)

LH012IWJ*** (P1.26) LH016IWJ*** (P1.68)

SNOW-1810U

Ver. 2.0 (2020.03.20)

Samsung Electronics

Revision History

Version Date (Y/M/D)

Description

2.0 2020/03/20

New

Release

Samsung Electronics

 When humidity get into LED package because of high humidity, it is

possible to cause ‘Line defect’ by electrical short in side of LED

Package.

 For keeping quality of products during installation, please refer below

cautions.

- If one of below case meet before installation, MUST do dehumidification process.

∙ Case when vacuum packaging is broken before unpacking.

∙ Case when environment condition is exceed Samsung recommended operation condition.

(Please refer Operation condition from User manual)

∙ Case when period between unpacking and turning on the power of products is spent

more than 7days, even though it is under Samsung recommended storage condition.

∙ Case when production date on the label is exceed more than 6 months, even though

vacuum packaging is no problem.

- When Volatile chemicals such as oil paint, solvent are used or operation condition

is exceed around of products installed place, MUST play video more than 2 hours everyday.

- If it is not meet with upper cases, it is helpful to play video more than 2 hours

everyday for protection for humidity getting into LED Package.

Dehumidification guidance – during installation

Samsung Electronics

 Electrical short in package is possible to happen during products are

working.

 For keeping quality of products during installation, please refer below

cautions.

- If one of below case meet during operation, MUST do dehumidification process.

∙ Case when environment condition is exceed operation condition.

∙ Case when products are not working more than 1 month, even though environment

condition is under operation condition.

- When environment condition is exceed operation condition, products are out of

warranty. Please check environment condition.

- Even products are operating, if the installed place have extra construction such as

interior modification, MUST do dehumidification following installation condition.

- It is possible to happen dew condensation on surface of products, even though

working on operating condition. When happening dew condensation, MUST operate after cleaning the dew condensation & dehumidification.

Dehumidification guidance – during operation

Samsung Electronics

Dew condensation due to overcooling

 Even though meet with Samsung recommended operation

condition, dew condensation is possible to happen when surface of products is colder than environment temperature or hot & humid air blow to cooled surface of products.

(cf : Principle of happening dew on surface of glass which have ice)

 Case when dew condensation is happen on products, it is

possible to be the root of defect. In this case, it is possible to be out of warranty.

Samsung Electronics

 When install products, please update latest firmware on online

- You can download latest firmware from SLM site.

∙ URL of SLM Page : https://www.secslm.com

∙ After login  Help  Download Center에서 Download

∙ Before you download firmware, you MUST check same firmware of model (marked red

letter in below) & upper number of version (marked blue in below).

- You can update firmware through LSM.

∙ Please refer ‘7-1 PC control program’ for the way to update firmware.

Guidance of latest firmware

Cabinet : Main - L-xxxMWWAC-nnnn.n  xxx = Pan name, nnnn.n = version

FPGA - aabbb_ddddd  aa = pixel pitch, bbb = LED package type, ddddd= version

Example : IER P2.5  Cabinet : L-IERMWWAC-1003.1, FPGA : 25252-31046

S-box : TB-KTM2SBMDWWC_100x.x

Samsung Electronics

Check first before Installation (1/2)

• For HDBT signal stability, use the cable above CAT6 *STP, *FTP level. ( Length 15m~100m )

- Do not use “comb” or “pinstripe” cable.

“CAT6 UTP can not be allowed”

• All Power cables and OCM cable must be connected firmly

• Do not mix cabinet which have different Project number, each cabinet have its own project

number.

Module Cabinet

Box

Samsung Electronics

Check first before Installation (2/2)

• Install the device only using SNOW-1810U and its supplied IG.

※ Please check below Cabinet and S-box compatibility table information

S-Box

SNOW-1810U SNOW-1703ULD SNOW-1703U

I/G

BN91-20525A BN91-19993A BN91-19100A

Cabinet

IF015H, IF020H,

IF025H,

IF025H-D, IF040H-D, IF060H-D,

IF012J,

IW008J

IW012J

IW016J

IF015H, IF020H,

IF025H,

IF025H-D, IF040H-D, IF060H-D,

IF012J

IF015H, IF020H,

IF025H,

IF025H-D, IF040H-D,

IF060H-D

Samsung Electronics

Table of Contents

1. Product Information and Precautions for Installation ( 4 page )

2. Check Point about the Radiant Heat ( 9 page )

3. Preparation for Cabinet Installation ( 15 page )

4. Frame Installation ( 22 page )

5. Cabinet + Frame Installation ( 30 page )

6. Disassembly & Front Service ( 41 page )

7. Cable Connection ( 58 page )

8. S-BOX Installation and Connection ( 71 page )

9. LSM Settings and How to Use ( 88 page )

10. Issue and Solution ( 103 page )

11. Color Calibration ( 104 page )

12. Bezel Installation ( 107 page )

13. Annex ( 115 page )

Samsung Electronics

◇ Cabinet Infomation

IW008J (P0.84) IW012J (P1.26) IW016J (P1.68)

Basic Spec.

Pitch

0.84 mm 1.26 mm 1.68 mm

Cabinet Resolution 960 X 540 640 X 360 480 X 270

Color Spec.

Brightness (Max)

1600-nit/500-nit 1600-nit/800-nit 1400-nit/1000-nit

Contrast Ratio

10,000:1

Viewing angle (H/V)

145°/155° 140°/160° 135°/155°

Refresh rate

1920 Hz ~ 3840 Hz

Power Spec.

Input Power

100~240 VAC, 50/60 Hz

Power consumption (Max)

190 (W/Cabinet) 192 (W/Cabinet) 180 (W/Cabinet)

Operation

Spec.

Working Temperature

0℃~+40℃/10~80%RH

IP Rating

IP20

Power Daisy Chain (220V / 110V)

4sets / 3sets

Certification

Spec.

Safety

60950-1

EMC

Class B

1. Product Information and Precautions for Installation

Samsung Electronics

◇ Screen configuration by model (Pitch) (Refer to page 22 for frame kit)

1. Product Information and Precautions for Installation

◇ SBB-SNOWJAU (S-Box, I/G)

◇ Cabinet Product Information

Specification

IWJ

P0.84 P1.26 P1.68

Cabinet

Cabinet Size

806.4 x 453.6 x 72.2 806.4 x 453.6 x 72.2 806.4 x 453.6 x 72.8

Module Size

201.6 mm x 151.2 mm

Weight

12.5kg 12.2kg 12.5kg

Screen

FHD

Cabinet Q’ty

2x2 (4set) 3x3 (9set) 4x4 (16set)

I/G Q’ty

1 1 1

Size

1612.8mm X 907.2mm 2419.2mm X 1360.8mm 3225.6mm X 1814.4mm

Frame Kit

VG-LFJ08FWW VG-LFJ08TWW VG-LFJ08UWW

Bezel

IWJPA-WP008D2X2 IWJPA-WP008D3X3 IWJPA-WP008D4X4

UHD

Cabinet Q’ty

4x4 (16set) 6x6 (36set) 8x8 (64set)

I/G Q’ty

4 4 4

Size

3225.6mm X 1814.4mm

4838.4mm X 2721.6mm 6451.2mm X 3628.8mm

Frame Kit

VG-LFJ08UWW VG-LFJ08TWW x4 VG-LFJ08UWW x4

Bezel

IWJPA-WP008D4X4 IWJPA-WP008D3X3 IWJPA-WP008D4X4

(S-Box)

(I/G x4ea)

Interface Gender

Samsung Electronics

1. Product Information and Precautions for Installation

• Precautions for Installation (LED damage)

Caution Image

[ Beware of Outside Impact, Fall]

① Beware not to cause any impact on the LED screen or drop the product on the floor after the protection gets taken off for installation. ② Beware not to put the LED side headed downwards to the floor after the protection

gets taken off for installation.

③ Beware not to have the corner area of LED module be damaged due to the contact with the outside.

④

Beware not to put more than 12 layers.

①

②

③

④

[Beware of LED Damage due to Static Electricity]

▶

Beware not to touch LED screen with bare hands without putting gloves on.

[Beware of LED & Film Damage due to Metallic Substances]

▶

Beware not to have metallic substances pulled in to the surface

due to the magnetic force on the front side of the LED.

▶

If any metallic substances get drawn in on the surface, please disassemble the

module and then remove the pollutants by using a magnet.

[Beware of LED Damage due to chemicals.]

▶

Beware not to contact water, waxes, benzene, thinners, mosquito repellents,

lubricants, cleaners, solvents or surfactants on LED.

▶

When installing on the construction site, it should be installed after construction & cleaning.

▶

If the installation site requires construction work, the product is covered with a

curtain and operated 50% white or video for 2 hours every day.

MODULE

Front

LED &

Film

Samsung Electronics

1. Product Information and Precautions for Installation

◇ Caution for cleaning screen

- It is recommended to wipe with a soft cleaning cloth provided

with the product. If there is a contamination area that is not removed well, a small amount of glass detergent of the surfactant component is sprayed on the cleaning cloth provided. (However, do not spray the glass detergent directly on the screen)

- Hard stuff on screen surface can damage LED chip and film during cleaning. Clear screen surface before cleaning

- Watch out for damage when cleaning gap between HalfCabinets

- Watch out for damage when cleaning gap between Modules

- Do not insert any cleaning tool or spay cleaner directly into the gap

- Do not wipe the LED surface with hard materials such as paper towels, brushes comb or brush, acrylic or steel.

- Do not use chemicals such as wax, benzene, cinna, mosquito

repellent, air freshener, lubricant, and detergent in products

★Caution★

Samsung Electronics

1. Product Information and Precautions for Installation

• Preparations for Installation

MAGNET JIG

(BN81-17114A)

(-) (+) driver

Absorber

(BN81-17124A) x4

Adjustment tool

(BN81-17112A)

GAP-TOOL

(BN81-17113A)

Glove

(RA00400E-002539)

Hex Wrench

2mm, 6mm

PLIER

(BN81-17541A)

• Provided in Frame Kit. (VG-LFJ08*WW).

• Provided in accessory kit. (CY-WJJPWP).

PROTECTION

(BN81-17111A)

EDGE PROTECTION V/H

(BN81-17514A/BN81-17515A)

• Provided in Frame Kit.

(BN96-48298A)

Cover-PCB

(BN63-18008A)

SCREW-MACHINE

HOLDER-SCREW

(BN61-16452B)

※ Packed in a small zipper bag

M4, L6

M3, L6

Samsung Electronics

2. Check Point about the Radiant Heat

 Standard and condition for indoor installation

- Standard for using ‘SAMSUNG WALL MOUNT’ (Fulfill ADA)

- Ceiling installation, outdoor installation, cannot be installed where there is vibration

It is not possible to install it in a special case, and it is necessary to consult technical sales

separately.

- In principle, solar window direct radiation condition installation is avoided.

- Window side, adjacent installation

. A weak solar scan of the time zone except for the noon time zone during work is allowed

. If surface temperature rise is minor (1 ~ 2 degrees) allowed

. Use UV blocking / light blocking film when installation of window adjacent is inevitable.

- Room temperature is recommended to be 0 ~ 25 ℃

- Effect of Cold / Hot Wind on Air Conditioning System

. If the cold or hot air is the same air conditioning system, be careful not to affect the product.

- Air temperature measurement position

. Based on product center or air let part

※ ADA(American’s with Disabilities Act

98.6mm

26.1mm

wall

Measuring

location for

ambient

temperature

Measuring

location for

ambient

temperature

※ Written under ‘Full white, (back light 7)’ standard

Written under ‘Video, (back light 10)’ standard

Samsung Electronics

 Minimum spacing for buried installation

Min 60mm

WALL

Min 60mm

Min 100mm (set ~ floor)

2. Check Point about the Radiant Heat– without Fan

※ Vent and interior finishing work will proceed after screen installation

Recommended condition : Min 500mm (set ~ ceiling) Min 100mm when maintaining the indoor temperature below 25 degrees due to air conditioning operation

Air vent area

Must use mesh with an opening rate of 60% or more

Air vent area Must use mesh with an opening rate of 60% or more

※ At least 60mm installation space required for upper, lower, left, and right All interior finishes proceed after screen installation

Samsung Electronics

 Minimum spacing for buried installation

Air vent area

WALL

Min 100mm (set ~ floor)

Recommended condition : Min 500mm (set ~ ceiling) Min 100mm when maintaining the indoor temperature below 25 degrees due to

air conditioning operation

2. Check Point about the Radiant Heat– without Fan

Samsung Electronics

Min 60mm

WALL

Min 60mm

 Example of minimum spacing and placement during landfill installation

left and right sealing

Min 100mm (set ~ floor)

Excluding FAN

should be sealed

Air vent area must use mesh with

an opening rate of 60% or more

Air vent area Must use mesh with an opening rate of 60% or more

Min 60mm

2. Check Point about the Radiant Heat– with Fan

※ Vent and interior finishing work will proceed after screen installation

Recommended condition : Min 500mm (set ~ ceiling) Min 100mm when maintaining the indoor temperature below 25 degrees due to

air conditioning operation

Samsung Electronics

WALL

 Example of minimum spacing and placement when installing walls

Min 100mm (set ~ floor)

2. Check Point about the Radiant Heat– with Fan

※ Vent and interior finishing work will proceed after screen installation

left and right sealing

Excluding FAN

should be sealed

Air vent area must use mesh with an

opening rate of 60% or more

Recommended condition : Min 500mm (set ~ ceiling) Min 100mm when maintaining the indoor temperature below 25 degrees due to

air conditioning operation

Samsung Electronics

left and right sealing

 Example of minimum spacing and placement during rear exhaust

Excluding FAN

should be sealed

The SCREEN wall is managed below 30 ℃ on the back of the wall.

WALL

Min 60mm

Min 100mm (set ~ floor)

2. Check Point about the Radiant Heat– with Fan

※ Vent and interior finishing work will proceed after screen installation

Recommended condition : Min 500mm (set ~ ceiling) Min 100mm when maintaining the indoor temperature below 25 degrees due to

air conditioning operation

Air vent area Must use mesh with an opening rate of 60% or more

Samsung Electronics

3. Preparation for Cabinet Installation

• Preparations Before Installation

① Remove the Box tape at the upper area and then open up the box. (Fig.2) ② Remove the Top–Cushion and hold the handle inside PE-Bag and pull out the set then remove PE bag.

(Fig.2)

③ Check whether there is any abnormality on the screen by connecting the power cable.(Fig.3)

※ Process of Screen check (Page.21)

Fig.1 Packing & Product

Fig. 2 Remove Al-Bag

Fig.3 Check the Screen

HANDLE

BOX

CUSHION-TOP

CUSHION-BOTTOM

LED-SET

SWITCH

Al-Bag

Samsung Electronics

3. Preparation for Cabinet Installation

④ 18ea Holder-PCB fixing screws and 4 Cover-PCB fixing screws are released.

⑤ Remove the filament tape attached to the top / bottom / left / right.

Fig.4 Holder-PCB & Cover-PCB & Protective Sheet Removal

X18

HOLDER-PCB COVER-PCB

Filament Tape

※ Remove Cover-PCB and screws and keep them separately.

It is required when working on the back.

※ The Cover-PCB, Screw, and Bolt are included in the accessory of the Cabinet

SCREW-MACHINE (6003-000133, M4,L8)

SCREW-MACHINE (6003-001501, M3,L6)

Samsung Electronics

3. Preparation for Cabinet Installation

⑥ Unfasten the 4 screws on the Cover Corner area to separate those screws and

Remove the protective sheet attached to the two sides (Top/Bottom). (Fig.4)

Fig.4 Cover Corner Removal

SCREW

SCREW-MACHINE (6003-000133, M4L8)

Samsung Electronics

3. Preparation for Cabinet Installation

- Using Spacer-PET

⑦ When Black Seam occurs, remove the Spacer-PET of the point.

※ Spacer-PET should not protrude more than module

⑧ If necessary, attach Spacer-PET. (Fig.5)

※ Check the gap between the module and the Bracket-Sub using a gap gauge.

※ If the step is 0.06mm or more, attach Spacer-PET (0.05t / 0.1t).

Step compensation by attaching GapSheet

Fig.5 Check the difference between the

module and B / SUB

Using Gap gauge

※ Spacer-PET :

- In order to minimize the load applied to the module during large size installation, Attach it to the Bracket-Sub to minimize the gap between the module and the Bracket-Sub.

- Cabinet 8poiont attached to Spacer-PET

Samsung Electronics

3. Preparation for Cabinet Installation

◈ Dehumidification

① In order to protect LED devices, the following items must be dehumidified.

[Dehumidification when Installed]

- If it is installed after more than 6 months in vacuum-packed condition after factory shipment.

- Storage for more than one week should be performed without vacuum treatment.

[Dehumidification during Use]

- Dehumidification is performed in an environment of 40 ℃ / 80% or less for 30 days or more. (Refer to LSM dehumidification, page 102page)

② How to dehumidify before installation

- Press the button for 3 seconds after the cabinet is turned on. ※ When the initial AC power is turned on, time required for operation of AM3352 IC is required.

Wait about 30 seconds and let it go. When the button is released, Dehumidifying Mode is executed. (Display the module at the top left)

- Aging with 24 hours on.

3초

Aging 24 hours

SWITCH

※ Caution

♦ The normal installation mode of operating IWJ (LH008IWJMWS, LH012IWJMWS, LH016IWJMWS) is “ STB ” mode (switch).

Please use "O" mode only for cabinet landing inspection and change it to "STB" mode after inspection.

♦ The switch that performs the factory dehumidification mode and factory reset function is the same. If you press 3 seconds, you enter

dehumidification mode. If you press 10 seconds or more, the factory reset is performed.

Samsung Electronics

3. Preparation for Cabinet Installation

◈ Process of Dehumidification

- The Dehumidification process progresses automatically for 24 hours as the brightness increases gradually.

Step condition Brightness Time

1 Lighting up display with 10 gray scale 5% 2 hr

2 Lighting up display with 20 gray scale 8% 2 hr

3 Lighting up display with 30 gray scale 10% 2 hr

4 Lighting up display with 40 gray scale 15% 2 hr

5 Lighting up display with 50 gray scale 20% 2 hr

6 Lighting up display with 70 gray scale 25% 2 hr

7 Lighting up display with 90 gray scale 35% 2 hr

8 Lighting up display with 120 gray scale 45% 2 hr

9 Lighting up display with 150 gray scale 60% 2 hr

10 Lighting up display with 180 gray scale 70% 2 hr

11 Lighting up display with 200 gray scale 80% 2 hr

12 Lighting up display with 255 gray scale 100% 2 hr

Samsung Electronics

3. Preparation for Cabinet Installation

◈ Reference : Process of Screen check

화면 검사 사진 확인

Check the picture of the screen

◈ Internal white pattern

1. After turn on power, press the toggle switch button for five seconds

2. Dehumidification screen comes out, push the toggle switch twice

3. when the white screen is displayed, check the defective LED by sequentially pressing toggle switch

* Do not turn on the white pattern over 10 seconds before dehumidification

4. if you need more brighter pattern, push ‘toggle switch’ button for three(3) seconds in white pattern

5. push toggle switch for three(3) seconds again to exit factory OSD

POWER INLET

POWER OUTLET

SWITCH

TOGGLE SWITCH

Samsung Electronics

4. Frame Installation

◇ Frame Kit Composition.

ⓐ

ⓑ

ⓒⓑ

ⓓ

ⓗ

M5,L65

ⓔ

ⓘ

ⓙ

ⓕ

ⓖ

ⓚ

ⓛ

ⓜ

Item

-LFJ08S

-LFJ08F

-LFJ08T

-LFJ08U

1x1 2x2 3x3 4x4

Units Units Units Units

ⓐ

BRACKET H (horizontal)

2 2 2 6

ⓑ

BRACKET SIDE (vertical)

2 2 2 2

ⓓ JOINT H 2 2 2 3

ⓔ JOINT V 2 4 6 8

ⓕ BRACKET JIG 1 1 1 1

ⓖ LEVELER - 2 2 2

ⓗ SCREW 4 6 6 15

ⓘ

Anchor

4 6 6 15

ⓙ

DRY WALL SCREW

4 6 6 15

ⓚ

MANUAL-INSTALL

1 1 1 1

ⓛ

ALIGN JIG

- - 1 1

ⓜ

LEVEL

- 1 1 2

ⓝ

HOLDER PCB

15 30 45 60

Installation Screen Size (mm)

806.4x453.6

1612.8x907.2

2419.2*1360.8

3225.6*1814.4

ⓝ

Samsung Electronics

4. Frame Installation

① Assemble Bracket Side/Middle with Bracket H.

- First insert ⓐBracket H to assembled Joint H and Bracket H. (Fig.1)

- Second put 3 groups of Bracket H on ground. And insert Bracket Side/Middle to Bracket H. (Fig.2)

- Then fasten up the screws. (Fig.3)

Fig.1 Insert Bracket H

Fig.2 Insert Bracket V to Bracket H

Fig.3 Fix Bracket with screw

M4L8

M6L8

ⓐ

ⓑ,ⓒ

ⓑ

ⓒ

ⓐ

Samsung Electronics

4. Frame Installation

② Assemble Leveler on the Bracket Side at required height position.

- Put Leveler on Bracket side at required height position with moving up and down. (Fig.1)

Fig.1 Assemble Leveler

M4L8 Screw

+ 94 hidden pages