Datasheet K4M511533E Datasheet (SAMSUNG)

查询K4M511533E供应商

K4M511533E - Y(P)C/L/F

8M x 16Bit x 4 Banks Mobile SDRAM in 54FBGA

FEATURES

• 3.0V or 3.3V power supply.

• LVCMOS compatible with multiplexed address.

• Four banks operation.

• MRS cycle with address key programs.

-. CAS latency (1, 2 & 3).

-. Burst length (1, 2, 4, 8 & Full page).

-. Burst type (Sequential & Interleave).

• EMRS cycle with address key programs.

• All inputs are sampled at the positive going edge of the system
clock.

• Burst read single-bit write operation.

• Special Function Support.

-. PASR (Partial Array Self Refresh).

-. Internal TCSR (Temperature Compensated Self Refresh)

• DQM for masking.

• Auto refresh.

• 64ms refresh period (8K cycle).

• Commercial Temperature Operation (-25°C ~ 70°C).

• 2 /CS Support.

• 2chips DDP 54Balls FBGA with 0.8mm ball pitch
( -YXXX : Leaded , -PXXX : Lead Free).

Mobile-SDRAM

GENERAL DESCRIPTION

The K4M511533E is 536,870,912 bits synchronous high data
rate Dynamic RAM organized as 4 x 8,388,608 words by 16 bits,
fabricated with SAMSUNG’s high performance CMOS technol­ogy. Synchronous design allows precise cycle control with the
use of system clock and I/O transactions are possible on every
clock cycle. Range of operating frequencies, programmable
burst lengths and programmable latencies allow the same
device to be useful for a variety of high bandwidth and high per­formance memory system applications.

ORDERING INFORMATION

Part No. Max Freq. Interface Package

K4M511533E-Y(P)C/L/F75 133MHz(CL=3)
K4M511533E-Y(P)C/L/F1H 105MHz(CL=2)
K4M511533E-Y(P)C/L/F1L

- Y(P)C/L/F : Normal / Low Power, Commercial Temperature(-25°C ~ 70°C)

Notes :

1. In case of 40MHz Frequency , CL1 can be supported.

2. Samsung shall not offer for sale or sell either directly or through and third-party proxy, and DRAM memory products that include "Multi-Die Plastic
DRAM" for use as components in general and scientific computers such as, by way of example, mainframes, servers, work stations or desk top
computers for the first three years of five year term of this license. Nothing herein limits the rights of Samsung to use Multi-Die Plastic DRAM in other
products or other applications under paragrangh such as mob ile, telecom or non-computer application(which include by way of example laptop or
notebook computers, cell phones, televisions or visual monitors)
Violation may subject the customer to legal claims and also excludes any warranty against infringement from Samsung." .

3. Samsung are not designed or manufactured for use in a device or system that is used under circumstance in which human life is potentially at stake.
Please contact to the memory marketing team in samsung electronics when considering the use of a product contained herein for any specific
purpose, such as medical, aerospace, nuclear, military, vehicular or undersea repeater use.

105MHz(CL=3)

*1

LVCMOS

54 FBGA

Leaded (Lead Free)

February 2004

K4M511533E - Y(P)C/L/F

FUNCTIONAL BLOCK DIAGRAM

CLK, /CAS, /RAS,

/WE, DQM, CKE

/CS1

/CS0

Mobile-SDRAM

16Mx16

16Mx16

DQ0~DQ15

A0~A12, BA0, BA1

February 2004

K4M511533E - Y(P)C/L/F

Package Dimension and Pin Configuration

Mobile-SDRAM

*2

>

RAS WE

Row Address Strobe

Write Enable

[Unit:mm]

1

*1

>

E/2

*2

>

SEC Week

XXXX

e

D

D/2

A

A1

z

b

123789
A VSS DQ15 VSSQ VDDQ DQ0 VDD
B DQ14 DQ13 VDDQ VSSQ DQ2 DQ1
C DQ12 DQ11 VSSQ VDDQ DQ4 DQ3
D DQ10 DQ9 VDDQ VSSQ DQ6 DQ5
EDQ8CS1
F UDQM CLK CKE CAS
G A12 A11 A9 BA0 BA1 CS0
HA8A7A6A0A1A10
J VSS A5 A4 A3 A2 VDD

Pin Name Pin Function

CLK System Clock

0 ~ 1 Chip Select

CS

CKE Clock Enable

A

0 ~ A12 Address

BA

0 ~ BA1 Bank Select Address

RAS
CAS

WE

L(U)DQM Data Input/Output Mask

0 ~ 15 Data Input/Output

DQ
V

DD/VSS Power Supply/Ground

V

DDQ/VSSQ Data Output Power/Ground

Symbol Min Typ Max

A 1.00 1.10 1.20

A

1

E-11.5-

E

1

D - 10.0 -

D

1

e - 0.80 ­b 0.40 0.45 0.50
z--0.10

< Bottom View

E

521634897

A
B
C
D

1

D

E
F
G
H
J

E

*2: Top View

*1: Bottom View

< Top View

#A1 Ball Origin Indicator

K4M511533E

< Top View

54Ball(6x9) FBGA

VSS VDD LDQM DQ7

Column Address Strobe

0.27 0.32 0.37

-6.40-

-6.40-

February 2004

K4M511533E - Y(P)C/L/F

Mobile-SDRAM

ABSOLUTE MAXIMUM RATINGS

Parameter Symbol Value Unit

Voltage on any pin relative to V
Voltage on V

DD supply relative to Vss VDD, VDDQ -1.0 ~ 4.6 V

ss VIN, VOUT -1.0 ~ 4.6 V

Storage temperature T
Power dissipation P
Short circuit current I

NOTES:

Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded.
Functional operation should be restricted to recommended operating condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.

STG -55 ~ +150 °C

D 1.0 W

OS 50 mA

DC OPERATING CONDITIONS

Recommended operating conditions (Voltage referenced to VSS = 0V, TA = -25°C ~ 70°C)

Parameter Symbol Min Typ Max Unit Note

Supply voltage

Input logic high voltage VIH 2.2 3.0 VDDQ + 0.3 V 1
Input logic low voltage VIL -0.3 0 0.5 V 2
Output logic high voltage VOH 2.4 - - V IOH = -2mA
Output logic low voltage VOL - - 0.4 V IOL = 2mA
Input leakage current ILI -10 - 10 uA 3

NOTES :

1. VIH (max) = 5.3V AC.The overshoot voltage duration is ≤ 3ns.

2. VIL (min) = -2.0V AC. The undershoot voltage duration is ≤ 3ns.

3. Any input 0V ≤ VIN ≤ VDDQ.
Input leakage currents include Hi-Z output leakage for all bi-directional buffers with tri-state outputs.

4. Dout is disabled, 0V ≤ VOUT ≤ VDDQ.

VDD 2.7 3.0 3.6 V

VDDQ 2.7 3.0 3.6 V

CAPACITANCE (VDD = 3.0V & 3.3V, TA = 23°C, f = 1MHz, VREF =0.9V ± 50 mV)

Pin Symbol Min Max Unit Note

Clock CCLK 3.0 12.0 pF
RAS, CAS, WE, CKE CIN 3.0 12.0 pF
CS CIN 1.5 6.0 pF
DQM CIN 3.0 12.0 pF
Address CADD 3.0 12.0 pF
DQ0 ~ DQ15 COUT 6.0 13.0 pF

February 2004

K4M511533E - Y(P)C/L/F

DC CHARACTERISTICS

Recommended operating conditions (Voltage referenced to VSS = 0V, TA = -25 to 70°C)

Mobile-SDRAM

Parameter Symbol Test Condition

Operating Current
(One Bank Active)

Precharge Standby Current in
power-down mode

Precharge Standby Current
in non power-down mode

Active Standby Current
in power-down mode

Active Standby Current
in non power-down mode
(One Bank Active)

Operating Current
(Burst Mode)

Version

-75 -1H -1L

Burst length = 1

ICC1

t

RC ≥ tRC(min)

I

O = 0 mA

ICC2P CKE ≤ VIL(max), tCC = 10ns 1.5

ICC2PS CKE & CLK ≤ VIL(max), tCC = ∞ 1.5

CKE ≥ VIH(min), CS ≥ VIH(min), tCC = 10ns

ICC2N

Input signals are changed one time during 20ns

ICC2NS

ICC3PS CKE & CLK ≤ VIL(max), tCC = ∞ 8

ICC3NS

CKE ≥ VIH(min), CLK ≤ VIL(max), tCC = ∞
Input signals are stable

ICC3P CKE ≤ VIL(max), tCC = 10ns 8

CKE ≥ VIH(min), CS ≥ VIH(min), tCC = 10ns

ICC3N

Input signals are changed one time during 20ns
CKE ≥ VIH(min), CLK ≤ VIL(max), tCC = ∞

Input signals are stable

100 90 85 mA 1

20

10

45 mA

35 mA

IO = 0 mA

Page burst

ICC4

4Banks Activated
t

CCD = 2CLKs

145 125 115 mA 1

Unit Note

mA

mA

mA

Refresh Current ICC5 tRC ≥ tRC(min) 190 170 160 mA 2

-C 1800

-L 1500 5

Self Refresh Current ICC6 CKE ≤ 0.2V

NOTES:

1. Measured with outputs open.

2. Refresh period is 64ms.

3. Internal TCSR can be supported(In commercial Temp : Max 40°C/Max 70°C).

4. K4M511533E-Y(P)C**

5. K4M511533E-Y(P)L**

6. K4M511533E-Y(P)F**

7. Unless otherwise noted, input swing IeveI is CMOS(VIH /VIL=VDDQ/VSSQ).

Internal TCSR Max 40 Max 70 °C 3

Full Array 850 1300

-F

1/2 of Full Array 600 900
1/4 of Full Array 500 700

uA

uA 6

4

February 2004

K4M511533E - Y(P)C/L/F

Mobile-SDRAM

AC OPERATING TEST CONDITIONS

Parameter Value Unit

AC input levels (Vih/Vil) 2.4 / 0.4 V
Input timing measurement reference level 1.4 V
Input rise and fall time tr/tf = 1/1 ns
Output timing measurement reference level 1.4 V
Output load condition See Figure 2

VDDQ

1200Ω

Output

870Ω

VOH (DC) = 2.4V, IOH = -2mA
VOL (DC) = 0.4V, IOL = 2mA

30pF

(VDD = 2.7V ∼ 3.6V, TA = -25 to 70°C)

Output

Vtt=0.5 x VDDQ

50Ω

Z0=50Ω

30pF

Figure 1. DC Output Load Circuit

Figure 2. AC Output Load Circuit

February 2004

K4M511533E - Y(P)C/L/F

OPERATING AC PARAMETER

(AC operating conditions unless otherwise noted)

Mobile-SDRAM

Parameter Symbol

Row active to row active delay tRRD(min) 15 19 19 ns 1
RAS to CAS delay tRCD(min) 19 19 24 ns 1
Row precharge time tRP(min) 19 19 24 ns 1

Row active time

Row cycle time tRC(min) 64 69 84 ns 1
Last data in to row precharge tRDL(min) 2 CLK 2
Last data in to Active delay tDAL(min) tRDL + tRP - 3
Last data in to new col. address delay tCDL(min) 1 CLK 2
Last data in to burst stop tBDL(min) 1 CLK 2
Col. address to col. address delay tCCD(min) 1 CLK 4
Number of valid output data CAS latency=3 2
Number of valid output data CAS latency=2 1
Number of valid output data CAS latency=1 0

NOTES:

1. The minimum number of clock cycles is determined by dividing the minimum time required with clock cycle time and then rounding off to the next
higher integer.

2. Minimum delay is required to complete write.

3. Minimum tRDL=2CLK and tDAL(= tRDL + tRP) is required to complete both of last data write command(tRDL) and prech arge command(tRP).

4. All parts allow every cycle column address change.

5. In case of row precharge interrupt, auto precharge and read burst stop.

tRAS(min) 45 50 60 ns 1

tRAS(max) 100 us

-75 -1H -1L

Version

Unit Note

ea 5

February 2004

K4M511533E - Y(P)C/L/F

AC CHARACTERISTICS(AC operating conditions unless otherwise noted)

Mobile-SDRAM

Parameter Symbol

CLK cycle time CAS latency=3 tCC 7.5
CLK cycle time CAS latency=2 tCC 9.5 9.5 12
CLK cycle time CAS latency=1 tCC - - 25
CLK to valid output delay CAS latency=3 tSAC 5.4 7 7
CLK to valid output delay CAS latency=2 tSAC 7 7 8
CLK to valid output delay CAS latency=1 tSAC - - 20
Output data hold time CAS latency=3 tOH 2.5 2.5 2.5
Output data hold time CAS latency=2 tOH 2.5 2.5 2.5
Output data hold time CAS latency=1 tOH - - 2.5
CLK high pulse width tCH 2.5 3.0 3.0 ns 3
CLK low pulse width tCL 2.5 3.0 3.0 ns 3
Input setup time tSS 2.0 2.5 2.5 ns 3
Input hold time tSH 1.0 1.5 1.5 ns 3
CLK to output in Low-Z tSLZ 1 1 1 ns 2

CAS latency=3

CLK to output in Hi-Z

CAS latency=2 7 7 8

tSHZ

-75 -1H -1L

Min Max Min Max Min Max

9.5

1000

5.4 7 7

1000

9.5
1000 ns 1

Unit Note

ns 1,2

ns 2

ns

CAS latency=1 - - 20

NOTES :

1. Parameters depend on programmed CAS latency.

2. If clock rising time is longer than 1ns, (tr/2-0.5)ns should be added to the parameter.

3. Assumed input rise and fall time (tr & tf) = 1ns.
If tr & tf is longer than 1ns, transient time compensation should be considered,
i.e., [(tr + tf)/2-1]ns should be added to the parameter.

February 2004

K4M511533E - Y(P)C/L/F

Mobile-SDRAM

SIMPLIFIED TRUTH TABLE

COMMAND CKEn-1 CKEn CS RAS CAS WE DQM BA0,1 A10/AP

Register Mode Register Set H X L L L L X OP CODE 1, 2

Auto Refresh

Refresh

Bank Active & Row Addr. H X L L H H X V Row Address
Read &

Column Address

Write &
Column Address

Burst Stop H X L H H L X X 6

Precharge

Clock Suspend or
Active Power Down

Precharge Power Down
Mode

DQM H X V X 7

No Operation Command H X

Self
Refresh

Auto Precharge Disable
Auto Precharge Enable H 4, 5

Auto Precharge Disable
Auto Precharge Enable H 4, 5

Bank Selection
All Banks X H

Entry L 3

Exit L H

Entry H L

Exit L H X X X X X

Entry H L

Exit L H

H

H X L H L H X V

H X L H L L X V

H X L L H L X

H

L L L H X X

L H H H
H X X X 3

H X X X

H X X X
L H H H
H X X X
L V V V

H X X X
L H H H

X X

V L

X

X

X

X X

A12,A11,

A9 ~ A0

L Column

Address
(A0~A8)

L Column

Address
(A0~A8)

X

XL V V V

X

Note

3

3

4

4

(V=Valid, X=Don′t Care, H=Logic High, L=Log ic Lo w)

NOTES :

1. OP Code : Operand Code
A0 ~ A12 & BA0 ~ BA1 : Program keys. (@MRS)

2. MRS can be issued only at all banks precharge state.
A new command can be issued after 2 CLK cycles of MRS.

3. Auto refresh functions are the same as CBR refresh of DRAM.
The automatical precharge without row precharge command is meant by "Auto".
Auto/self refresh can be issued only at all banks precharge state.

Partial self refresh can be issued only after setting partial self refresh mode of EMRS.

4. BA0 ~ BA1 : Bank select addresses.

5. During burst read or write with auto precharge, new read/write command can not be issued.
Another bank read/write command can be issued after the end of burst.
New row active of the associated bank can be issued at tRP after the end of burst.

6. Burst stop command is valid at every burst length.

7. DQM sampled at the positive going edge of CLK masks the data-in at that same CLK in write operation (W ri te DQM latency is 0), but i n read opera tion,
it makes the data-out Hi-Z state after 2 CLK cycles. (Read DQM latency is 2).

February 2004

K4M511533E - Y(P)C/L/F

Mobile-SDRAM

A. MODE REGISTER FIELD TABLE TO PROGRAM MODES

Register Programmed with Normal MRS

Address

Function

BA0 ~ BA1

"0" Setting for Normal

MRS

A12 ~ A10/AP

*1

RFU

*2

A8 A7 A6 A5 A4 A3 A2 A1 A0

A9

W.B.L Test Mode CAS Latency BT Burst Length

Normal MRS Mode

Test Mode CAS Latency Burst Type Burst Length

A8 A7 Type A6 A5 A4 Latency A3 Type A2 A1 A0 BT=0 BT=1

0 0 Mode Register Set 0 0 0 Reserved 0 Sequential 0 0 0 1 1
0 1 Reserved 0 0 1 1 1 Interleave 0 0 1 2 2
1 0 Reserved 0 1 0 2 Mode Select 0 1 0 4 4
1 1 Reserved 0 1 1 3 BA1 BA0 Mode 0 1 1 8 8

Write Burst Length 1 0 0 Reserved

A9 Length 1 0 1 Reserved 1 0 1 Reserved Reserved

0 Burst 1 1 0 Reserved 1 1 0 Reserved Reserved
1 Single Bit 1 1 1 Reserved 1 1 1 Full Page Reserved

0 0

Setting

for Nor-

mal MRS

1 0 0 Reserved Reserved

Full Page Length x16 : 512Mb(1024)

Register Programmed with Extended MRS

Address BA1 BA0 A12 ~ A10/AP A9 A8 A7 A6 A5 A4 A3 A2 A1 A0

Function Mode Select

RFU

*1

DS

RFU

*1

PASR

EMRS for PASR(Partial Array Self Ref.) & DS(Driver Strength)

Mode Select Driver Strength PASR

BA1 BA0 Mode A6 A5 Driver Strength A2 A1 A0 Size of Refreshed Array

0 0 Normal MRS 0 0 Full 0 0 0 Full Array
0 1 Reserved 0 1 1/2 0 0 1 1/2 of Full Array
1 0 EMRS for Mobile SDRAM 1 0 Reserved 0 1 0 1/4 of Full Array
1 1 Reserved 1 1 Reserved 0 1 1 Reserved

Reserved Address 1 0 0 Reserved

A12~A10/AP A9 A8 A7 A4 A3 1 0 1 Reserved

0 0 0 0 0 0

NOTES:

1. RFU(Reserved for future use) should stay "0" during MRS cycle.

2. If A9 is high during MRS cycle, "Burst Read Single Bit Write" function will be enabled.

1 1 0 Reserved
1 1 1 Reserved

February 2004

K4M511533E - Y(P)C/L/F

Mobile-SDRAM

Partial Array Self Refresh

1. In order to save power consumption, Mobile SDRAM has PASR option.

2. Mobile SDRAM supports 3 kinds of PASR in self refresh mode : Full Array, 1/2 of Full Array and 1/4 of Full Array.

BA1=0
BA0=0

BA1=1
BA0=0

BA1=0
BA0=1

BA1=1
BA0=1

BA1=0
BA0=0

BA1=1
BA0=0

- Full Array - 1/2 Array

BA1=0
BA0=1

BA1=1
BA0=1

BA1=0
BA0=0

BA1=1
BA0=0

- 1/4 Array

BA1=0
BA0=1

BA1=1
BA0=1

Partial Self Refresh Area

Internal Temperature Compensated Self Refresh(Internal TCSR)

1. In order to save power consumption, Mobile-DRAM includes the internal temperature sensor and control units to control the self
refresh cycle automatically according to the two temperature range : Max 40 °C and Max 70 °C(for Commercial Temperature).

2. If the EMRS for external TCSR is issued by the controller, this EMRS code for TCSR is ignored.

Self Refresh Current (Icc6)

Temperature Range

Max 70 °C
Max 40 °C 850 600 500

- C - L
Full Array 1/2 of Full Array 1/4 of Full Array

1300 900 700

1800 1500

- F

Unit

uA

B. POWER UP SEQUENCE

1. Apply power and attempt to maintain CKE at a high state and all other inputs may be undefined.

- Apply VDD before or at the same time as VDDQ.

2. Maintain stable power, stable clock and NOP input condition for a minimum of 200us.

3. Issue precharge commands for all banks of the devices.

4. Issue 2 or more auto-refresh commands.

5. Issue a mode register set command to initialize the mode register.

6. Issue a extended mode register set command to define DS or PASR operating type of the device after normal MRS.

EMRS cycle is not mandatory and the EMRS command needs to be issued only when DS or PASR is used.
The default state without EMRS command issued is the full driver strength and full array refreshed.
The device is now ready for the operation selected by EMRS.
For operating with DS or PASR , set DS or PASR mode in EMRS setting stage.
In order to adjust another mode in the state of DS or PASR mode, additional EMRS set is required but power up sequence is not
needed again at this time. In that case, all banks have to be in idle state prior to adjusting EMRS set.

February 2004

K4M511533E - Y(P)C/L/F

Mobile-SDRAM

C. BURST SEQUENCE

1. BURST LENGTH = 4

Initial Address

A1 A0

0 0 0 1 2 3 0 1 2 3
0 1 1 2 3 0 1 0 3 2
1 0 2 3 0 1 2 3 0 1
1 1 3 0 1 2 3 2 1 0

Sequential Interleave

2. BURST LENGTH = 8

Initial Address

A2 A1 A0

0 0 0 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7
0 0 1 1 2 3 4 5 6 7 0 1 0 3 2 5 4 7 6
0 1 0 2 3 4 5 6 7 0 1 2 3 0 1 6 7 4 5
0 1 1 3 4 5 6 7 0 1 2 3 2 1 0 7 6 5 4
1 0 0 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3
1 0 1 5 6 7 0 1 2 3 4 5 4 7 6 1 0 3 2
1 1 0 6 7 0 1 2 3 4 5 6 7 4 5 2 3 0 1
1 1 1 7 0 1 2 3 4 5 6 7 6 5 4 3 2 1 0

Sequential Interleave

February 2004