Page 1
COLOR TELEVISION RECEIVER
Chassis : K15A
Model: TXJ1366
TXJ1367
TXJ1396
TXJ1966
TXJ1996
COLOR TELEVISION RECEIVER CONTENTS
Precautions
Specifications
Disassembly and Reassembly
Alignment and Adjustments
Troubleshooting
Exploded Views and Parts List
Electric Parts List
Block Diagram
PCB Layout
Wiring Diagrams
Schematic Diagrams
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Page 2
1. Precautions
1-1 Safety Precautions
1. Be sure that all of the built-in protective
devices are replaced. Restore any missing
protective shields.
2. When reinstalling the chassis and its
assemblies, be sure to restore all protective
devices, including: nonmetallic control knobs
and compartment covers.
3. Make sure that there are no cabinet openings
through which peopleÑparticularly
childrenÑmight insert fingers and contact
dangerous voltages. Such openings include
the spacing between the picture tube and the
cabinet mask, excessively wide cabinet
ventilation slots, and improperly fitted back
covers.
If the measured resistance is less than 1.0
megohm or greater than 5.2 megohms, an
abnormality exists that must be corrected
before the unit is returned to the customer.
4. Leakage Current Hot Check (Figure 1-1):
Warning: Do not use an isolation
transformer during this test. Use a leakagecurrent tester or a metering system that
complies with American National Standards
Institute (ANIS C101.1, Leakage Current for
Appliances), and Underwriters Laboratories
(UL Publication UL1410, 59.7).
5. With the unit completely reassembled, plug
the AC line cord directly into the power
outlet. With the unitÕs AC switch first in the
ON position and then OFF, measure the
current between a known earth ground (metal
water pipe, conduit, etc.) and all exposed
metal parts, including: antennas, handle
brackets, metal cabinets, screwheads and
control shafts. The current measured should
not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the
test.
Fig. 1-1 AC Leakage Test
6. Antenna Cold Check:
With the unitÕs AC plug disconnected from the
AC source, connect an electrical jumper across
the two AC prongs. Connect one lead of the
ohmmeter to an AC prong. Connect the other
lead to the coaxial connector.
7. X-ray Limits:
The picture tube is especially designed to prohibit X-ray emissions. To ensure continued
X-ray protection, replace the picture tube only
with one that is the same type as the original.
Carefully reinstall the picture tube shields and
mounting hardware; these also provide X-ray
protection.
8. High Voltage Limits:
High voltage must be measured each time servicing is done on the B+, horizontal deflection
or high voltage circuits. Correct operation of
the X-ray protection circuits must be
reconfirmed whenever they are serviced.
(X-ray protection circuits also may be called
Òhorizontal disableÓ or Òhold-downÓ.)
Heed the high voltage limits. These include
the XÐray Protection Specifications Label, and
the Product Safety and X-ray Warning Note on
the service data schematic.
Precautions
Samsung Electronics 1-1
LEAKAGE
CURRENT
TESTER
DEVICE
UNDER
TEST
TEST ALL
EXPOSED METAL
SURFACES
2-WIRE CORD
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
EARTH
GROUND
(READING SHOULD
NOT BE ABOVE
0.5mA)
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential
hazards such as electrical shock and X-rays.
Page 3
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified
limits by close-tolerance, safety-related
components and adjustments. If the high
voltage exceeds the specified limits, check
each of the special components.
10. Design Alteration Warning:
Never alter or add to the mechanical or
electrical design of this unit. Example: Do not
add auxiliary audio or video connectors. Such
alterations might create a safety hazard. Also,
any design changes or additions will void the
manufacturerÕs warranty.
11. Hot Chassis Warning:
Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord. If an isolation transformer is not
used, these units may be safely serviced only
if the AC power plug is inserted so that the
chassis is connected to the ground side of the
AC source.
To confirm that the AC power plug is inserted
correctly, do the following: Using an AC
voltmeter, measure the voltage between the
chassis and a known earth ground. If the
reading is greater than 1.0V, remove the AC
power plug, reverse its polarity and reinsert.
Re-measure the voltage between the chassis
and ground.
12. Some TV chassis are designed to operate with
85 volts AC between chassis and ground,
regardless of the AC plug polarity. These units
can be safely serviced only if an isolation
transformer inserted between the receiver and
the power source.
13. Some TV chassis have a secondary ground
system in addition to the main chassis ground.
This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulating material that must not be defeated
or altered.
14. Components, parts and wiring that appear to
have overheated or that are otherwise
damaged should be replaced with parts that
meet the original specifications. Always
determine the cause of damage or overheating, and correct any potential hazards.
15. Observe the original lead dress, especially
near the following areas: Antenna wiring,
sharp edges, and especially the AC and high
voltage power supplies. Always inspect for
pinched, out-of-place, or frayed wiring. Do
not change the spacing between components
and the printed circuit board. Check the AC
power cord for damage. Make sure that leads
and components do not touch thermally hot
parts.
16. Picture Tube Implosion Warning:
The picture tube in this receiver employs
Òintegral implosionÓ protection. To ensure
continued implosion protection, make sure
that the replacement picture tube is the same
as the original.
17. Do not remove, install or handle the picture
tube without first putting on shatterproof
goggles equipped with side shields. Never
handle the picture tube by its neck. Some
Òin-lineÓ picture tubes are equipped with a
permanently attached deflection yoke; do not
try to remove such Òpermanently attachedÓ
yokes from the picture tube.
18. Product Safety Notice:
Some electrical and mechanical parts have
special safety-related characteristics which
might not be obvious from visual inspection.
These safety features and the protection they
give might be lost if the replacement component differs from the originalÑeven if the
replacement is rated for higher voltage,
wattage, etc.
Components that are critical for safety are
indicated in the circuit diagram by shading,
( ) or ( ).
Use replacement components that have the
same ratings, especially for flame resistance
and dielectric strength specifications.
A replacement part that does not have the
same safety characteristics as the original
might create shock, fire or other hazards.
Precautions
1-2 Samsung Electronics
!
Page 4
1-2 Servicing Precautions
1. Servicing precautions are printed on the
cabinet. Follow them.
2. Always unplug the unitÕs AC power cord from
the AC power source before attempting to: (a)
Remove or reinstall any component or
assembly, (b) Disconnect an electrical plug or
connector, (c) Connect a test component in
parallel with an electrolytic capacitor.
3. Some components are raised above the printed
circuit board for safety. An insulation tube or
tape is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.
4. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the portion around
the serviced part has not been damaged.
5. Check the insulation between the blades of the
AC plug and accessible conductive parts
(examples: metal panels, input terminals and
earphone jacks).
6. Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the
power switch ON. Connect an insulation
resistance meter (500V) to the blades of the AC
plug.
The insulation resistance between each blade
of the AC plug and accessible conductive parts
(see above) should be greater than 1 megohm.
7. Never defeat any of the B+ voltage interlocks.
Do not apply AC power to the unit (or any of
its assemblies) unless all solid-state heat sinks
are correctly installed.
8. Always connect a test instrumentÕs ground
lead to the instrument chassis ground before
connecting the positive lead; always remove
the instrumentÕs ground lead last.
Precautions
Samsung Electronics 1-3
Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between
the servicing and safety precautions, always follow the safety precautions.
Warning2: An electrolytic capacitor installed with the wrong polarity might explode.
Page 5
1. Some semiconductor (Òsolid stateÓ) devices
are easily damaged by static electricity. Such
components are called Electrostatically
Sensitive Devices (ESDs); examples include
integrated circuits and some field-effect
transistors. The following techniques will
reduce the occurrence of component damage
caused by static electricity.
2. Immediately before handling any semicon
ductor components or assemblies, drain the
electrostatic charge from your body by
touching a known earth ground. Alternatively,
wear a discharging wrist-strap device. (Be
sure to remove it prior to applying powerÑ
this is an electric shock precaution.)
3. After removing an ESD-equipped assembly,
place it on a conductive surface such as
aluminum foil to prevent accumulation of
electrostatic charge.
4. Do not use freon-propelled chemicals. These
can generate electrical charges that damage
ESDs.
5. Use only a grounded-tip soldering iron when
soldering or unsoldering ESDs.
6. Use only an anti-static solder removal device.
Many solder removal devices are not rated as
Òanti-staticÓ; these can accumulate sufficient
electrical charge to damage ESDs.
7. Do not remove a replacement ESD from its
protective package until you are ready to
install it. Most replacement ESDs are
packaged with leads that are electrically
shorted together by conductive foam,
aluminum foil or other conductive materials.
8. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.
9. Minimize body motions when handling
unpackaged replacement ESDs. Motions such
as brushing clothes together, or lifting a foot
from a carpeted floor can generate enough
static electricity to damage an ESD.
Precautions
1-4 Samsung Electronics
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
Page 6
ELECTRONICS
©
Samsung Electronics Co., Ltd. SEP. 1999
Printed in Korea
3K15A-1425
Page 7
Specifications
Samsung Electronics 2-1
2. Specifications
2-1 Specifications
Television System 14"/20"/21" NTSC COLOR TV SIGNAL
Power Consumption 14" : 57 WATTS NOMINAL,
20" : 70 WATTS NOMINAL
21" : 75 WATTS NOMINAL,
Picture Tube 14" : A34KQV42X
20" : A48KRD82X (H)
21": : A51KQJ63X (H)
Power Requirement AC 120V, 60Hz /AC 100 ~ 240, 50Hz, 60Hz
Operating System REMOCON SYSTEM (SZM354ET)
Tuning Ranges VHF CH : 2-13, UHF CH : 14-69, CABLE CH : 1,14-125
Antenna Input Impedance 75 ohm UNBALANCED TYPE FOR VHF/UHF
Intermediate Frequency PICTURE 45.75MHz, SOUND 41.25MHz,
COLOR SUB CARRIER 42.17MHz
Speaker Impedance Single:
Dual : 8 ohm 3W x 2
Dual : 16 ohm , 3W x 2 (CT-33H1, CT-50H1)
8 ohm 3W
Page 8
Disassembly and Reassembly
Samsung Electronics 3-1
3. Disassembly and Reassembly
3-1 Back Cover Removeal
Fig. 3-1
1. After removing the screws, pull the cabinet backwards.
Page 9
3-2 Main Board Removal
Disassembly and Reassembly
3-2 Samsung Electronics
Fig. 3-2
Fig. 3-3
1. Separate the socket board from the CRT neck.
2. Remove the Anode Cap from the CRT.
3. Remove the main board by pulling it with both hands.
Warning: The FBT is charged with high voltage.
Before removing the Anode Cap, discharge the voltage
through one of the heat sinks on the main board.
Page 10
Disassembly and Reassembly
Samsung Electronics 3-3
3-3 Speaker Removal
1. Loosen the screws and remove the speakers.
Fig. 3-4
Page 11
Disassembly and Reassembly
3-4 Samsung Electronics
3-4 CRT Removel
Fig. 3-5
1. Spread a soft mat on the floor. Place the TV set face down.
2. Remove the 4 nuts mounting the CRT to the front cabinet.
3. Lift the CRT.
4. Caution: Because of the high vacuum and large surface area of the
picture tube, be careful while handling it:
(1) Always lift the picture tube by grasping it firmly around the faceplate, (2) Never lift the tube by its neck. (3) Do not scratch the picture
tube or apply excessive pressure. Fractures of the glass may cause an
implosion.
Page 12
Alignment and Adjustments
Samsung Electronics 4-1
4. Alignment and Adjustments
4-1 Service Mode Adjustments
4-1-1 Service Mode Menus
Since there are no VRs in the K15A chassis, all
adjustments after parts replacement must be
done in the Service Mode. Service Mode
adjustments are necessary when either the
EEPROM (IC902) or the CRT is replaced.
4-1-2 Entering the Service Mode
Press the following transmitter keys
while in STAND-BY mode:
MUTE—>1—>8—>2—>POWER
“Factory Mode Menu” is displayed
<---selected (violet)
RC XXX
VCO XX GC XXX
SBT XX BC XX
SCT XX VA XX
SCR XX VS XX
STT XXX HS XX
GG XXX SS XX
BG XXX SVC : MUTE
AGC XX
AGC XX RC XXX
GC XXX
SBT XX BC XX
SCT XX VA XX
SCR XX VS XX
STT XXX HS XX
GG XXX SS XX
BG XXX SVC : MUTE
VCO XX
VCO
71
AGC XX XXX
XXX
XX XX
XX VA XX
XX VS XX
XXX HS XX
XXX SS XX
XXX
SVC : MUTE
VCO XX
RC
GC
SBT
BC
SCT
SCR
STT
GG
BG
ADJUSTMENT
PATTERN
OPTION
RESET
ADJUSTMENT
PATTERN
OPTION
RESET
Enter Service Mode using the Volume
+,- keys. Service Mode Menu:
Return to the Service mode by pressing
MENU.
Change the data with “Volume +, - “ keys.
Return to the Factory mode via the MENU
key.
Press POWER to enter the Stand-by mode.
Select a mode to be adjusted, using the channel down key. Example: VCO.
Page 13
POWER
OFF
No
Item Function
Range
MICOM Data
1 AGC RF AGC Adjustment 0~63 50
2 VCO PIF VCO Adjustment 0~127 63
3 SCT SUB-CONTRAST Adjustment 0~63 48
4 SCR SUB-COLOR Adjustment 0~27 13
5 STT SUB-TINT Adjustment 0~27 7
6 RC RED-CUT OFF Adjustment 0~255 0
7 GC GREEN-CUT OFF Adjustment 0~255 0
8 BC BLUE-CUT OFF Adjustment 0~255 0
9 SVC Input a Horiz line pattern
10 GG GREEN-GAIN Adjustment 0~255 127
11 BG BLUE-GAIN Adjustment 0~255 127
12 SBT SUB-BRIGHTNESS Adjustment 0~63 31
13 VA VERTICAL SIZE Adjustment 0~63 39
14 VS VERTICAL CENTER Adjustment 0 0
15 HS HORIZONTAL Phase Adjustment 0~31 15
16 SS SUB-SHARPNESS Adjustment 0~31 4
BYTE 0 : 0 0
ADJUSTMENT
PATTERN
OPTION
RESET
ADJUSTMENT
PATTERN
OPTION
RESET
ADJUSTMENT
PATTERN
OPTION
RESET
ADJUSTMENT
PATTERN
OPTION
RESET
ADJUSTMENT
PATTERN
OPTION
RESET
Initalized
Alignment and Adjustments
4-2 Samsung Electronics
4-1-3 Adjustment in Option Mode
This adjustment is necessary whenever the
EEPROM is replaced. Input data (as marked
on the back cabinet).
Select “SET OPTION” by pressing the
Channel key twice.
Press the Volume +, - keys to enter the set
Option mode.
Press MENU to go back to the factory mode.
Select RESET with channel key.
Press volume + key.
▼
▼
4-1-4 Service Mode Adjustments
1. The Pattern Adjustment is done only in the
factory. Do not attempt to readjust it.
2. Refer to 4-2 for other adjustments.
3. Set OPTION data.
4-1-5 Service Mode Adjustment Ratings
Note : The initial MICOM data values take
effect when IC902 is replaced.
Page 14
Alignment and Adjustments
Samsung Electronics 4-3
4-2 Alignment and Adjustment
4-2-1 General Alignment Instructions
1. Usually, a color TV needs only slight
touch-up adjustment upon installation. Check
the basic characteristics such as picture height,
focus and a horizontal and vertical sync.
2. Observe the picture and check for good back
and white details. There should be no
objectionable color shading: If color shading is
present, demagnetize the receiver. If color
shading persists, perform purity and
convergence adjustments described below.
3. To protect against shock hazard, use an
isolation transformer.
4-2-2 Power Supply Check
Check the following:
A: Power plug is connected; “Stand-by” mode
B: Power On when “Power ON” button is pressed
C: Power On by FBT Each supply is marked on
its lead-in wire. ( )
4-2-3 Focus Adjustment
Adjust the focus control on the FBT for well
defined scanning lines.
4-2-4 Fail Safe Circuit Check (FS) (OPTION)
1. The failsafe check must be the final step in
servicing.
2. Turn the power switch ON and adjust
customer controls for normal operation.
3. Temporarily short pin X to pin R on the main
board (RX06, RX04) with a jumper wire.
Raster will disappear.
4. The TV must remain in this state even after
removing the jumper wire. This shows that
the failsafe circuit is working properly.
5. To recover picture and sound, temporarily
turn off the TV and allow the failsafe circuit
more than 30 seconds to reset. Then switch
power ON to produce normal picture and
sound.
4-2-5 IC902 Replacement
1. When IC902 is replaced, all values are reset to
“Initialized MICOM Data” and readjustment
is necessary.
2. Press the POWER button 10 seconds after
plug-in.
3. To enter the Service Mode, refer to Fig. 4-1
(Service Mode Adjustment).
4-2-6 PIF VCO Adjustment
1. Use a Pattern Generator or an off-air signal.
2. Open pin 11 of Micom (IC901) or one side of
lead pin for R237.
3. Adjust VCO in the service mode to set IC101
Pin 44 (AFT) to 2.5V ± 0.4V.
4. Connect the opened site.
4-2-7 RF-AGC Adjustment
1. Input a PHILLIPS pattern.
2. Set the input signal to 60 dB.
3. Enter into the AGC in the service mode.
4. Adjust AGC until color bar noise disappears.
Page 15
Alignment and Adjustments
4-4 Samsung Electronics
4-2-8 Sub-Contrast Adjustment
1. Input a gray scale pattern. Use a pattern
generator (PM5518).
2. Short D208 to switch off the ABL feed-back.
3. Check CN201 R-OUT with an oscilloscope.
4. Set RC, BC, GC data to 0 in the Service Mode.
5. Adjust SCT to 2.40 ± 0.1Vp-p
6. Remove the short across D208 and restore
ABL.
4-2-9 Sub-Tint Adjustment
1. Input a rainbow pattern.
2. Check CN201 B-OUT with an oscilloscope.
3. Adjust STT in the service mode until the 6th
peak is the highest and the 5th and 7th peaks
have equal heights.
4-2-10 Sub-Color Adjustment
1. Do sub-color adjustment after the SubContrast and Sub-Tint adjustments.
2. D208 should still be shorted. The ABL should
still be switched OFF.
3. Input a color bar pattern. Use a pattern generator (PM5518).
4. Check CN201 R-OUT (use an oscilloscope).
5. Ensure that the RC, GC and BC data are 0.
BG are 140 and GG should be 90.
6. Adjust SCR to 2.4 ± 0.1Vp-p (black and
red levels).
7. Remove the short across D208 and restore
ABL.
2.5V 0.1Vpp
+
_
1
2
3
4
5
6
7
8
9
10
2.4V 0.1Vpp
+
_
Page 16
Alignment and Adjustments
Samsung Electronics 4-5
4-2-11 White Balance Adjustment
4-2-11 (A) LOW-LIGHT ADJUSTMENTS
1. Input either a lion head or “pure white” color
pattern.
2. Operate the receiver for 30 minutes.
3. Check the data in the service mode:
RC, GC, BC are 0 and SB is 16;
Steps BG are 90 and GG are 140.
4. Enter the horizontal line mode by pressing
the MUTE key.
5. Adjust the screen VR on the FBT until a dim
colored line (red,green or blue) appears on the
screen.
6. After pressing the MUTE key, go to RC,BC or
GC with channel , keys. After putting a
dim colored line (red, green or blue) in the
horizontal line with MUTE key, adjust color
with volume , keys.
7. Exit the horizontal line via the MUTE key.
4-2-11 (B) HIGH-LIGHT ADJUSTMENTS
1. Input a high-light pattern
2. Adjust GG,BG in the Service Mode.
3. Recheck in low light.
4-2-12 Sub-Brightness Adjustment
1. Input a Toshiba pattern.
2. Warm up the receiver for 10 minutes.
3. Enter the Service Mode and set SB to the point
where the 5th point is brighter in the gray
scale.
4-2-13 Vertical Size Adjustment
1. Input a lion head pattern.
2. After the vertical center adjustment, enter into
the service mode.
3. Adjust VA so that the each top and bottom of
the screen is 4.0. If the top and bottom values
are different, adjust VA so that the sum of the
two values is 8.0.
4-2-14 Horizontal Size Adjustment
1. Receive a lion head pattern.
2. Enter into the service mode.
3. Adjust HS to symmetrized right and left.
4-2-15 When CRT Is Replaced
Do the following adjustments after the basic
purity and convergence adjustments.
1. White Balance
2. Sub-brightness
3. Vertical Size
4. Horizontal Size
5. Fail safe (should be the final step).
W
5
4 3
2 1
▼
▼
▼
▼
Page 17
MEMO
4-6 Samsung Electronics
Page 18
Troubleshooting
Samsung Electronics 5-1
5. Troubleshooting
5-1 No Power
Normal
Check LED when AC
code is plugged.
Check
Fuse.
OFF
No Power
Check
IC801* Pin 1
Oscillation.
Check
IC801 Pin 3 B+.
Abnormal
Abnormal (0 ~ 15V)
Check/Replace
D806, Q401, Q801,
D802, D814*
Check and Replace
D807 ~D810
Abnormal
Abnormal (0V)
Normal (15~20V)
Check/Replace
PC802, DZ807
Check IC801*
Pin 4 Voltage
Check IC802.
Check/Replace
IC802, R812, D856.
ON
Abnormal
Normal (0.5 ~ 3V)
Check/Replace
DZ802, DZ803, D806
Page 19
5-2 No Sound
Troubleshooting
5-2 Samsung Electronics
Abnormal
Abnormal
Normal
Normal
Normal
Abnormal
Abnormal
Abnormal
Normal
Normal (approx. 12V)
No Sound
Check
Connector CN601
and CN701.
Check
Waveform of
IC601 Pin 1.
Check
Waveform of IC201
Pin 52.
Check
Waveform of IC201
Pin 1.
Volume
Up.
Check
SIF (L201).
Check/Replace
IC201.
Abnormal
Check
Waveform of IC601 and
IC602 Pins 4.
Check CN601 and CN701
Connector
Soldering and A/V PCB.
Check
Voltage of IC601 and IC602
Pin 5.
Check Power
12V Line Voltage.
Replace IC601
and IC602.
O.K
NG
Ok
Normal
Page 20
5-3 Horizontal Line Appears
Troubleshooting
Samsung Electronics 5-3
Abnormal
Normal (24V)
Abnormal
Check/Replace
IC201.
NG
Single Horizontal Line
Check
24V-C Voltage.
Check
Waveform of IC201
Pins 22,24.
Normal
O.K
Check Whether
a horizontal line appears in
the service mode..
Check/Replace
IC301.
Check
FBT Pin 2 (24V)
Oscillation.
Normal
NG
Check R409
Open.
Check/Replace
R409.
Open
Check/Replace
FBT.
Page 21
Troubleshooting
5-4 Samsung Electronics
5-4 No Signal
Abnormal
Normal
No Signal
Normal
Normal
Abnormal
Abnormal
Abnormal
Normal
Normal
Abnormal
Normal (2Vp-p)
Normal (1Vp-p)
Normal (3~5Vp-p)
Abnormal
Normal (2Vp-p)
Normal (1Vp-p)
Check
each tuner terminal
voltage.
Check voltage
line.
Check
Micom IC901.
Check
tuner SCL,SDA
waveform.
Check
tuner IF terminal
waveform.
Check
IC201 Pins 7,8
waveform.
Replace tuner.
Check
whether AGC and
AFTadjustment are normal in
the service mode.
Check
IC201 Pin 47
waveform level.
Check IC201
Pin 37 waveform
level.
Readjust AGC
and AFT.
Check IC201 Pin 41
waveform level.
Check
IC201 Pin 43 waveform
level.
Check
IC201 Pins 19,20, 21
waveform level.
Check CRT PCB (180V)
and heater Voltages.
Replace IC201.
Page 22
Exploded Views & Parts List
Samsung Electronics 6-1
6. Exploded Views & Parts List
No Code No Description Specification Q’ty Remark
1 AA92-30161EA ASSY-CABINET,FRONT TXJ1366,9,V0,S/V,K15A 1
AA64-00162A CABINET-FRONT 14F2,BK708P,HIPS,V0,BLK 1
1-1 AA64-70127F BADGE-BRAND AL,SS,SILVER,R800 1
1-2 AA64-00165B KNOB-POWER 14F2,NO-SILK,ABS,HB,BLK 1
1-3 AA61-60003J SPRING-CS -,-,SUS304,0.5,OD6,H 1
1-4 AA60-10002A SCREW-TAPPING -,RH,+,M4,L12,ZP 2 PA+CF
1-5 ASSY-PCB,A/V FRONT
1-6 AA65-30105A CLAMP-WIRE NYLON 66N,VO,NTR,15MM 1
1-7 AA61-40113A STOPPER-PCB -,ABS,HB,NTR. 1
1-8 AA64-00167B INDICATOR-LED 14F2,ACRYL,CLR, 1
1-9 AA64-00166B WINDOW-REMOCON 14F2,PC,VIOLET 1
1-10 6002-000512 SCREW-TAPPING RH,+,2,M4,L12,ZP 1 WIN+CF
1-11 AA64-00164B KNOB-CONTROL 14F2,ABS,HB,BLK 1
1-12 6002-000512 SCREW-TAPPING RH,+,2,M4,L12,ZP 1 KC+CF
1-13 3001-000281 SPEAKER-GENERAL 2.5W8OHM77MM7 1
2 AA03-10001D CRT-COLOR -,A34KQV42X,+380MG,14,90DEG,5 1
2-1 L9400-0002 HOLDER-DEGAUSSING 20POLYVINI 2
2-2 AA60-10050Q SCREW-ASSY WC,HH,M5,L26.5,SWRCH, 4 CRT+CF
3 AA64-00259A CABINET-BACK -,14F2,-,HIPS,V0,BLK. 1
3-1 6002-000514 SCREW-TAPPING RH,+,2,M4,L15,ZP 4 CB+CF
3-2 L7000-0132 ANT-RODVHF 4SDODIPOLE850MMBRN 1 SECA
AA42-00001A ANT-ROD -,3S,650MM,ABS,UL/CSA 1 SEA
4 AA39-10007Y POWER-CORD -,EP2/YES,SPT-2 18AWGx2C,2.4m 1 PWR/AC
6-1 TXJ1366, TXJ1367, TXJ1396
Page 23
Exploded Views & Parts List
6-2 Samsung Electronics
No Code No Description Specification Q’ty Remark
1 AA92-30161NA ASSY-CABINET,FRONT TXJ1966,9,VO,S/V,K15A 1
AA64-00152A CABINET-FRONT 20F2,BK708P,HIPS,V0,BLK 1
1-1 AA64-70127F BADGE-BRAND AL,SS,SILVER,R800 1
1-2 AA64-00156B KNOB-POWER -,20F2,NO-SILK,ABS,HB,BLK 1
1-3 AA61-60003J SPRING-CS -,-,SUS304,0.5,OD6,H 1
1-4 AA61-40113A STOPPER-PCB -,ABS,HB,NTR. 1
1-5 ASSY-PCB,A/V FRONT
1-6 AA60-10002A SCREW-TAPPING -,RH,+,M4,L12,ZP 2 PA+CF
1-7 AA65-30105A CLAMP-WIRE NYLON 66N,VO,NTR,15MM 1
1-8 AA64-00157B WINDOW-REMOCON -,20F2,-,PC,VO,VIOLET,- 1
1-9 6002-000512 SCREW-TAPPING RH,+,2,M4,L12,ZP 1 WIN+CF
1-10 AA64-00155B KNOB-CONTROL -,20F2,-,ABS,HB,BLK 1
1-11 6002-000512 SCREW-TAPPING RH,+,2,M4,L12,ZP 1
1-12 3001-001020 SPEAKER 3W,8ohm,90dB,140Hz 1
1-13 6002-000514 SCREW-TAPPING RH,+,2,M4,L15,ZP 2 SPK+CF
2 LB03-10029W CRT-COLOR A48KRD82X(H)+380MG,SEMTNT.BZIL 1
2-1 L9400-0001 HOLDER-DEGAUSSING 25POLYVINYLCHLORIDEFL 4
2-2 AA60-10050R SCREW-ASSY WC,HH,+M5,L31.5,SWR 4
3 AA64-00154B CABINET-BACK -,20F2 R1,-,HIPS,V0,BLK,-,- 1
3-1 6002-000514 SCREW-TAPPING RH,+,2,M4,L15,ZP 4 CB+CF
3-2 AA42-00001A ANT-ROD -,3S,650MM,ABS,UL/CSA 1 TXJ1996
L7000-0132 ANT-RODVHF 4SDODIPOLE850MMBRN 1 TXJ1966
3-3 CABINET OPTION
4 AA39-10007Y POWER-CORD -,EP2/YES,SPT-2 18AWGx2C,2.4m 1 CORD/P
6-2 TXJ1966, TXJ1996
Page 24
7. Electric Parts List
Electric Parts List
Samsung Electronics 7-1
7-1 Part Differences (by screen size) .......................................................................................
7-2
TXJ1366 (TXJ1996 and TXJ1366 Dissimilar Parts) .........................................
7-3
TXJ1996 .................................................................................................................................
7-1
7-9
7-9
Page 25
No. Loc. No.
INC
H
U.S.A LATIN
SPECIFICATION CODE No. SPECIFICATION CODE No.
1 CRT
14" A34KQV42X,+380mG,14" AA03-10001D
20" A48KRD82X(H),+380mG,21" AA03- 10029W
2 DY
14" DSE-1422FL,14" AA27-50001K
¬Ÿ
20" DSE-1992LL1(H),20" AA27- 50004W
3 CY
14" 22.5MM AA27-60001E
20" -,JH-291-(JH-8210) AA27-60001D
4 V999
14" 7P,22.5PI,12PI, S N 3704-001089
20" 9P,15.24PI, 26.5PI,SN,- 3704-001090 CRT OCKET
5 T444
14" -,FSV-14A001,14",125V A A26-30004H B/R
20" -,FSV-20A001,20",125V A A26-30001Y B/R
6 CN802
14" 14",16.4ohm,75T AA27-20003U D-COIL
20" 20" JAPAN 6.2
W
AA27-20003F 20",14.4ohm,48T AA27-20003X D-COIL
7
TBCWIRE
14" 14" 1P AA98-70014A
20" 20" 1P AA98-70014B
8
ASSY-
CRT
14" A34KQV42X,+380mG,14",BARE AA94-50014P
20" A48KRD82X(H),+380MG,20",BARE A A94-50019X
Ÿ
¬Ÿ
¬Ÿ
¬Ÿ
¬Ÿ
¬Ÿ
¬Ÿ
¬Ÿ
¬Ÿ
¬Ÿ
¬Ÿ
REMARK
Electric Parts List
7-2 Samsung Electronics
7-1 Part Differences (by screen size)
Page 26
Electric Parts List
Samsung Electronics 7-3
7-1-1 Inch Option
No. Loc. No.
INC
H
U.S.A LATIN
SPECIFICATION CODE No. SPECIFICATION CODE No.
1 C402
14" C-C 722 1.6KV 2306-000253
¬Ÿ ¬Ÿ
HORIZONTAL CT CAPACITOR
20" C-C 742 1.6KV 2306-000355
¬Ÿ ¬Ÿ
2 C403
14" C-C 331 2KV 2201-000467
¬Ÿ ¬Ÿ
20" C-C 271 2KV 2201-000406
¬Ÿ ¬Ÿ
3 C404
14" C-MPP 334 250V 23 06-000004
¬Ÿ ¬Ÿ
20" C-MPP 364 200V 23 06-000193
¬Ÿ ¬Ÿ
4 L401
14" 195uH AA27-30001B
¬Ÿ ¬Ÿ
LINEARITY COIL
20" 195uH AA27-30001B
¬Ÿ ¬Ÿ
LINEARITY COIL
5 R404
14" R-C 22-J 1/2T 2001-000020
¬Ÿ ¬Ÿ
HDT B+
RESISTOR
20" R-C 36-J 1/2T 2001-001136
¬Ÿ ¬Ÿ
6 R411
14" R-M 120K-F 1/2T 2004-001377
¬Ÿ ¬Ÿ
ABL RESISTOR
20" R-M 100K-F 1/2T 2004-001373
¬Ÿ ¬Ÿ
7 R412
14" R-M 120K-F 1/2T 2004-001377
¬Ÿ ¬Ÿ
20" R-M 100K-F 1/2T 2004-001373
¬Ÿ ¬Ÿ
8 R413
14" R-C 0.39-K 1/2T 2001-003019
¬Ÿ ¬Ÿ
KSD5386 OPTION
20" JUMPER 3812-000219
¬Ÿ ¬Ÿ
KSD5386 OPTION
REMARK
HORIZONTAL CT CAPACITOR
HORIZONTAL CT CAPACITOR
HORIZONTAL CT CAPACITOR
HORIZONTAL CS CAPACITOR
HORIZONTAL CS CAPACITOR
HDT B+
RESISTOR
ABL RESISTOR
ABL RESISTOR
ABL RESISTOR
9 C301
14" C-P 273 100V 2301-000226
¬Ÿ
20" C-P 223 100V 2301-000223
¬Ÿ
10 C302
14" C-C 471 50V 2201-000556 C-C 561 50V 2201-000599
20" C-C 471 50V 2201-000556
¬Ÿ
11 C304
14" C-E 1uF 50V HR 2401-000553
¬Ÿ
20" C-E 1uF 50V HR 2401-000553
¬Ÿ
12 C305
14" C-P 473 100V 2305-000427
¬Ÿ
20" C-P 683-J 50V 2301-000310 C-P 104 100V 2305-000149
Page 27
Electric Parts List
7-4 Samsung Electronics
No. Loc. No.
INC
H
U.S.A LATIN
SPECIFICATION CODE No. SPECIFICATION CODE No.
13 C311
14" C-E 0.47uF 50V 2401-001333
¬Ÿ
20" C-E 0.47uF 50V 2401-001333
¬Ÿ
14 R303
14" R-C 56K-J 1/8T 2001-000864
¬Ÿ
20" R-C 62K-J 1/8T 2004-001990
¬Ÿ
15 R304
14" R-M.O 2W 3.3-J 2003-001036
¬Ÿ
20" R-M.O 1W 1.5-J 2003-000436
¬Ÿ
16 CN501
14" 8P 300MM AA39-20109D
¬Ÿ
20" 8P 400MM AA39-20109A
¬Ÿ
REMARK
17 R305
14" R-C 33K-J 1/8T 20 01-000660
¬Ÿ
20" R-M 7.5K-J 1/8T 2004-001213
¬Ÿ
18 R306
14" R-M 82K-J 1/8T 20 04-001301
¬Ÿ
20" R-C 43K-J 1/8T 20 01-000766
¬Ÿ
19 R307
14" R-C 36K-J 1/8T 20 01-000679
¬Ÿ
20" R-C 56K-J 1/8T 20 01-000864
¬Ÿ
20 R308
14" R-C 30K-J 1/8T 20 01-000633
¬Ÿ
20" R-M 62K-J 1/8T 20 04-001990
¬Ÿ
21 R309
14" R-M.O 330-J 1W 2003-000649
¬Ÿ
20" R-M.O 510-J 1W 2003-001043
¬Ÿ
22 R518
14" R-F 2W 1.0 20 08-000266 R-F 2W 1.5 2008-001015
20"
" "
R-F 2W 1.0 2008-000266
23 R518A
14" R-F 2W 1.5 20 08-000257
X X
20"
" " X X
24 J504
14"
X X
JUMPER 3 812-000219
20"
X X
JUMPER 3 812-000219
Page 28
Electric Parts List
Samsung Electronics 7-5
No. Loc. No.
INC
H
U.S.A LATIN
REMARK
SPECIFICATION CODE No. SPECIFICATION CODE No.
25 C216
14" C-C 20pF(CH) 2201-000354
¬Ÿ
20" C-C 20pF(CH) 2201-000354
X
26 R204
14" R-C 820-J 1/8T 2004-000995
¬Ÿ
20" R-C 1.2K-J 1/8T 2001-000221
¬Ÿ
27 R205
14" R-C 820-J 1/8T 2004-000995
¬Ÿ
20" R-C 1.2K-J 1/8T 2001-000221
¬Ÿ
28 R206
14" R-C 820-J 1/8T 2004-000995
¬Ÿ
20" R-C 1.2K-J 1/8T 2001-000221
¬Ÿ
29 R214
14" R-C 10K-J 1/8T 2001-000290
¬Ÿ
20" R-C 12K-J 1/8T 2001-000331
¬Ÿ
30 R222
14" R-C 470K-J 1/8T 2001-000773
¬Ÿ
DELETE
(INCH DOES NOT MATTER :
CHANGED TO 4570K)
20" R-C 470K-J 1/8T 2001-000773
¬Ÿ
31 R226
14" R-C 180K-J 1/8T 2001-000397
¬Ÿ
20" R-C 220K-J 1/8T 2001-000508
¬Ÿ
32 R257
14" R-F 1/2W 0.47 2008-000252 R-F 2W 1.0 2008-000266
20" " " " "
X
33 RH01
14"
X X X X
20" R-COMP 4.7K1/2T 2002-001006
¬Ÿ ¬Ÿ
34 RH02
14"
X X X X
20" R-COMP 4.7K1/2T 2002-001006
¬Ÿ ¬Ÿ
35 RM01
14" R-COMP 4.7K1/2T 2002-001006
¬Ÿ ¬Ÿ
20"
X X X X
36 RM02
14" R-COMP 4.7K1/2T 2002-001006
¬Ÿ ¬Ÿ
20"
X X X X
37 T444
14" FSV-14A001,14",125V AA26-30004H
¬Ÿ ¬Ÿ
20" FSV-20A001,14",125V AA26-30001Y
¬Ÿ ¬Ÿ
Page 29
Electric Parts List
7-6 Samsung Electronics
7-1-2 AC Input Option
No. Loc. No.
RELAY USED RELAY DELETE
SPECIFICATION CODE No. SPECIFICATION CODE No.
1 CU10 C-E 220uF 25V 2401-000832
X X
RELAY OPTION
2 J153
X X
JUMPER 3812-000219
APPLIED WHEN DELETING RELAY
3 JU14 JUMPER 3812-000219
X X
RELAY OPTION
4 JWU02
X X
JUMPER 3812-000219
5 L910 FERRIE BEAD 2901-000299
X X
RELAY
6 QU10 TR C2331-Y 0501-000369
X X
RELAY OPTION
7 P801
X X
POSISTOR 7ߟ3P 1404-001048 POSISTOR FREE VOLT
8 P801A POSISTOR 7ߟ2P 1404-000208
X X
POSISTOR SINGLE VOLT (110V)
9 RLU01 RELAY:HR-CR13 3501-001040
X X
RELAY OPTION
10 RU11 R-C 4.7K-J 1/8T 2001-000734
X X
RELAY OPTION
11 RU12 R-C 10K-J 1/8T 2001-000290
X X
RELAY OPTION
12 RU13 R-C 33-J 1/2T 2001-000022
X X
RELAY OPTION
13 DU01 DIODE 1N4004 0402-000132
X X
RELAY OPTION
No. Loc. No.
AC 110V ONLY FREE VOLT
REMARK
SPECIFICATION CODE No. SPECIFICATION CODE No.
1 C801 C-E:220uF 200V 2 401-000822 C-E:220uF 400V 2401-002298 110V/FREE VOLT
2 C804 C-C 400V 222 2201-000987 C-C 400V 332 2201-000446
COUNTERMEASURE ON SMPS NOISE
3 C819 C-C 400V 102 2201-000963
X X
4 IC801 STR S0765 AA96-50395A STR S0680 AA96-50298D
VOLTAGE DIFFERENCE (110V/220)
5 R802 R-M,OXIDE 36K1W 2003-002119 R-M,OXIDE 2W33K 2003-000994
6 R803 R-M,OXIDE 36K1W 2003-002119 R-M,OXIDE 2W33K 2003-000994
7 T801 EER2834 AA27- 20007L EER 354311 AA27-20006U TRANS
COUNTERMEASURE ON SMPS NOISE
VOLTAGE DIFFERENCE
(SINGLE VOLT/FREE VOLT)
VOLTAGE DIFFERENCE
(SINGLE VOLT/FREE VOLT)
REMARK
ADDED WHEN DELETING RELAY
7-1-3 Relay Option
Page 30
Electric Parts List
Samsung Electronics 7-7
7-1-4 X-Ray Option
No. Loc. No.
X-RAY USED X-RAY DELETE
REMARK
SPECIFICATION CODE No. SPECIFICATION CODE No.
1 CX01 C-C 103 25V 2202-000127
X X
X-RAY
2 CX02 10uF 50V 2401-000480
X X
X-RAY
3 CX03 10uF 50V 2401-000480
X X
X-RAY
4 CX04 471 500V 2201-000556
X X
X-RAY
5 DX01 MTZ6.2B 0403-000297
X X
X-RAY
6 DX02 1N4004 400V 04 02-000132
X X
X-RAY
7 JX01 JUMPER 3 812-000219
X X
X-RAY
8 QX01 KSA539-Y 0501-000283
X X
X-RAY
9 RX01 R-C 180K 1/8T 2 001-000397
X X
X-RAY
10 RX02 R-C 18K 1/8T 2001-000411
X X
X-RAY
12 RX03 R-M 4.3K-F 1/2T 2004-001987
X X
X-RAY
13 RX04 R-M 11K-F 1/2T 2004-001376
X X
X-RAY
14 RX05 R-C 22K 1/8T 2001-000522
X X
X-RAY
15 RX07 JUMPER 3812-000219
X X
X-RAY
16 RX08 R-C 51K 1/8T 2001-000837
X X
X-RAY
17 JWX01
X X
JUMPER 3812-000219
ADDED WHEN DELETING X-RAY
Page 31
Electric Parts List
7-8 Samsung Electronics
7-1-5 Sound Option (MONO/DUAL)
No. Loc. No.
~73, ~38, ~1F SYSTEM (1 SPK / 1 AMP)1 ~1H SYSTEM (2 SPKs / 1 AMP) ~39,~85,~66,~1E,~3E SYSTEM ( 2 SPKs / 2 AMPs)
SPECIFICATION CODE No. SPECIFICATION CODE No. SPECIFICATION CODE No.
1 IC602
X X X X
ASSY-H/S LA4425 AA96-50392A
WHEN USING 2 AMPs
2 C652
X X X X
2.2uF 50V 2401-000660
3 C655
X X X X
470uF 16V 2401-001363
4 JDW1
X X X X
JUMPER 38 12-000219 SOUND L OUT
5 JAW04
X X X X
JUMPER 38 12-000219 SOUND L OUT
6 CN603 POST HEADER 3P 3711-002642
X X X X
3P WHEN USING 1 SPEAKER
7 CN601
X X
POST HEADER 4P 3711-002643 POST HEADER 4P 3711-002643
4P WHEN USING 2 SPEAKERS
8 J601
X X
JUMPER 38 12-000219
X X
SOUND R/L CONNECTED
9 D814 RG10V 400V 0402-000534 RG10V 400V 0 402-000534 RK16 0404-001056 RK16 WHEN USING 2 AMPs
10 R604 R-C 2.2K 1/8T 2001-000449
¬Ÿ ¬Ÿ
R-C 3.3K 1/8T 2001-000591 3.3K 1/8T WHEN USING 2 AMPs
No. Loc. No. SPECIFICATION CODE No.
F-A/V DELETE F-A/V USED
REMARK
~1F SYSTEM ~1H SYSTEM OTHER CABINET
1 F-A/V
DELETE EARPHONE A/V
AA95-90030M
X O
DELETE EARPHONE
(FROM THE EXISTING F/A/V)
2 CN701 POST HEADER 7P 3711-002646
X O
ADDED WHEN USING F-A/V
3 JAW01 JUMPER 3812-000219
O X
ADDED WHEN DELETING F/A/V
4 JAW02 JUMPER 3812-000219
O X
REMARK
WHEN USING 2 AMPs
WHEN USING 2 AMPs
ADDED WHEN DELETING F/A/V
7-1-6 Front A/V Option
Page 32
Electric Parts List
Samsung Electronics 7-9
7-2 TXJ1366 (TXJ1996 and TXJ1366 Dissimilar Parts)
TXJ1366X/XAA, TXJ1366X/XAC, TXJ1367/XAC
TXJ1396X/XAA, TXJ1396X/XAC
ASSY-PCB,MAIN
* AA94-10133F2 ASSY-PCB,MAIN(COM);K15A(0),S/V,13,BLK, TXJ1366
AA94-10133F1 ASSY-PCB,MAIN(COM);K15A(0),S/V,13,WHT, TXJ1367
C301 2301-000020 C-FILMPEF;27NF,5%,100V,TP,7.3
C305 2305-000427 C-FILM,MPEF;47NF,5%,100V,7.5X
C402 2306-000253 C-FILM;CF922P1.6KVT722-JBUP
C404 2306-000004 C-FILM,MPPF;330NF,5%,250V,TP,
CN501 L6434-0084-030 CONNECTORASSY;B8XB8300M1007#2
R304 2003-001036 R-METALOXIDE(S);3.3OHM,5%,2W,
R307 2001-000679 R-CARBON;36KOHM,5%,1/8W,AA,TP
R308 2001-000633 R-CARBON;30KOHM,5%,1/8W,AA,TP
R309 2003-000649 R-METALOXIDE(S);330OHM,5%,1W,
R404 2001-001153 R-CARBON(S);47OHM,5%,1/2W,AA,
R411 2004-001377 R-METAL(S);120KOHM,1%,1/2W,AA,TP,2.4X6.4
R412 2004-001377 R-METAL(S);120KOHM,1%,1/2W,AA,TP,2.4X6.4
R413 2001-001037 R-CARBON(S);0.39OHM,5%,1/2W,A
T444 L7000-0032 TRANS-FLYBACK;FSV14A00114INCH
V999 3704-001089 SOCKET CRT;9P,22.5PI,12PI,SN,13
ASSY-SPEAKER
* AA96-10014A ASSY-SPEAKER;8OHM,2.5W,3(2),F/200
SPK 3001-000281 SPEAKER-GENERAL;2.5W8OHM77MM7
L/SPK AA39-20500A LEAD CONNECTOR-ASSY;-,67096-003,REC,3(2)
ASSY-ACCESSORY
A/ROD L7000-0132 ANT-RODVHF;4SDODIPOLE850MMBRN SECA
AA68-11252A INSTRCTION-BOOK;K15A,FRENCH,TM59,205X150 SECA
ASSY-CRT
* AA97-50001C ASSY-CRT;A34KQV42X,-,14INCH,ITC,-,MINI(
CRT AA03-10001D CRT-COLOR;-,A34KQV42X,+380MG,14,90DEG,5
C-Y AA27-00001A MAGNET-CONVERGENCE;JH225-06A,225MM
D-COIL AA27-20004C COIL-DEGAUSSING;-,14,4.5ohm,30T,L890,D
D-Y L7000-0005 DEFL-YOKE(SEMSA);DSE-1422FL
REMOCON
* AA59-10101M REMOCON; DP,TM59,-,-,AA59-10095T
ASSY-CABINET
* AA92-30161EA ASSY-CABINET,FRONT;TXJ1366,9,V0,S/V,K15A
L3113-0003-011 BOSS-CABINET;HIPSVOBLKCT-5073
AA64-00259A CABINET-BACK;-,14F2,-,HIPS,V0,BLK.
AA64-00162A CABINET-FRONT;14F2,BK708P,HIPS,V0,BLK
AA64-00167B INDICATOR-LED;14F2,ACRYL,CLR,
AA64-00164B KNOB-CONTROL;14F2,ABS,HB,BLK
AA64-00165B KNOB-POWER;14F2,NO-SILK,ABS,HB,BLK
AA60-10050Q SCREW-ASSY;WC,HH,M5,L26.5,SWRCH,
AA63-60001Z SPACER-FELT;-,FELT,T1.0,-,35X
AA64-00166B WINDOW-REMOCON;14F2,PC,VIOLET
ASSY-CLAMPERS
* L9100-000-001 ASSY-CLAMPERS;K1,K15A,13,DUA
CDCOIL L9400-0002 HOLDER-DEGAUSSING;20POLYVINI
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Page 33
Electric Parts List
7-10 Samsung Electronics
TXJ1966X/XAA, TXJ1966X/XAC, TXJ1996X/XAA
ASSY-PCB,MAIN
A/MAIN AA94-10133Z ASSY-PCB,MAIN(COM);K15A(O),S/V,19,MONO,
C101 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2
C102 2401-000660 C-ELECTROLYTIC;CE04WTAPG50V2.2
C104 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2
C108 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M
C110 2401-002594 C-AL;220uF,20%,16V,GP,TP,8x11.5,5
C151 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2
C153 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2
C201 2201-000292 C-CERAMIC,DISC;1NF,10%,50V,Y5P
C202 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4
C203 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C204 2301-000188 C-FILM,PEF;1NF,5%,100V,10.5X12
C205 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4
C206 2305-001011 C-FILM,MPEF;22NF,5%,100V,3.5X12.5X7.5MM,
C207 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4
C209 2305-000665 C-FILM;CF922N63VT104-J-40/1053
C210 2305-000665 C-FILM;CF922N63VT104-J-40/1053
C211 2305-000665 C-FILM;CF922N63VT104-J-40/1053
C212 2201-000982 C-CERAMIC,DISC;10NF,+80-20%,50
C213 2201-000193 C-CERAMIC,DISC;10PF,0.25PF,50V
C214 2401-000660 C-ELECTROLYTIC;CE04WTAPG50V2.2
C215 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1
C216 2201-000354 C-CERAMIC,DISC;20PF,5%,50V,NPO
C218 2301-000395 C-FILM,PEF;18nF,5%,50V,TP,6.5x12.5x3.5mm
C219 2401-000603 C-AL;1UF,20%,50V,GP,5X11MM,5MM
C220 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M
C221 2401-002462 C-ELECTROLYTIC;CE04WTAPG16V33M
C222 2305-000665 C-FILM;CF922N63VT104-J-40/1053
C225 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M
C226 2401-000603 C-AL;1UF,20%,50V,GP,5X11MM,5MM
C227 2305-000665 C-FILM;CF922N63VT104-J-40/1053
C229 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2
C230 2305-000665 C-FILM;CF922N63VT104-J-40/1053
C231 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C232 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C233 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M
C234 2301-000445 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm
C235 2202-000279 C-CERAMIC,MLC-AXIAL;47PF,5%,50
C236 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2
C237 2202-000791 C-CERAMIC,MLC-AXIAL;150pF,10%,50V,Y5P,TP
C301 2301-000016 C-FILMPEF;22NF,5%,100V,TP,7.2X
C302 2201-000556 C-CERAMIC,DISC;470PF,10%,500V,
C303 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2
C304 2401-000553 C-AL;1UF,10%,50V,GP,5X11MM,5MM
C305 2301-000310 C-FILM,PEF;68NF,5%,50V,8.0X8.5
C306 2401-002458 C-AL;1000UF,20%,35V,GP,16X25MM
C308 2301-000310 C-FILM,PEF;68NF,5%,50V,8.0X8.5
C309 2401-000360 C-AL;100UF,20%,50V,GP,8X11MM,5
C310 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M
C311 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4
C312 2401-000553 C-AL;1UF,10%,50V,GP,5X11MM,5MM
C313 2305-000470 C-FILM,MPEF;68NF,5%,100V,-,5MM
C401 2301-000224 C-FILM,PEF;22NF,5%,50V,7.4X3.9
C402 2306-000255 C-FILM;CF922P1.6KVT742-HBUP
C403 2201-000991 C-CERAMIC,HIC;CK45(T)B2KV561-K
C404 2306-000193 C-FILM,MPPF;360NF,5%,200V,-,7.
C405 2305-000704 C-M,POLYESTER;CFS922MTAPG250V1
C406 2201-000556 C-CERAMIC,DISC;470PF,10%,500V,
C407 2401-001429 C-ELECTROLYTIC;CE04WTAPG50V470
C408 2201-000556 C-CERAMIC,DISC;470PF,10%,500V,
C409 2401-001998 C-AL;1000UF,20%,25V,GP,TP,10X20
C410 2301-000224 C-FILM,PEF;22NF,5%,50V,7.4X3.9
C411 2201-000556 C-CERAMIC,DISC;470PF,10%,500V,
C412 2401-000927 C-AL;22UF,20%,250V,GP,13X20MM,
C413 2401-000560 C-AL;1UF,20%,160V,GP,GT,6.3,11MM
C444 2201-000441 C-CERAMIC,DISC;3.3nF,10%,500V,Y5P,TP,10x
C445 2201-000441 C-CERAMIC,DISC;3.3nF,10%,500V,Y5P,TP,10x
C501 2202-000863 C-CERAMIC;CKOAX7R50VT561-KUP050561
C502 2202-000862 C-CERAMIC;CCOASL50VT391-JUP050
C503 2202-000825 C-CERAMIC,MLC-AXIAL;680PF,10%,50V,Y5P,TP
C505 2201-002063 C-CERAMIC,DISC;10nF,+80-20%,3KV,Y5V,TP,1
C601 2401-000962 C-AL;22uF,20%,50V,GP,TP,5x11,5
C603 2301-000289 C-FILM,PEF;5.6NF,5%,50V,6.5X5.
C604 2401-000660 C-ELECTROLYTIC;CE04WTAPG50V2.2
C605 2305-000665 C-FILM;CF922N63VT104-J-40/1053
C609 2401-000133 C-AL;1000UF,20%,16V,GP,13X20MM
C611 2202-000279 C-CERAMIC,MLC-AXIAL;47PF,5%,50
C612 2202-000279 C-CERAMIC,MLC-AXIAL;47PF,5%,50
C651 2401-000660 C-ELECTROLYTIC;CE04WTAPG50V2.2
C654 2401-001363 C-AL;470UF,20%,16V,GP,TP,10X12
C701 2305-000665 C-FILM;CF922N63VT104-J-40/1053
C702 2401-000471 C-AL;10UF,20%,50V,BP,6X11MM,5M
C703 2202-000183 C-CERAMIC;CKOAX7R16VT222-MEP05
C705 2202-000183 C-CERAMIC;CKOAX7R16VT222-MEP05
C801 2401-000822 C-ELECTROLYTIC;CE04W200V220U-H
C802 2201-000119 C-CERAMIC,DISC;100NF,+80-20%,5
C803 2303-000163 C-FILM,PPF;2.2NF,5%,800V,-,-,T
C804 2201-000987 C-CERAMIC,AC;CK45PE400V222-M(T
C805 2201-000991 C-CERAMIC,HIC;CK45(T)B2KV561-K
C806 2401-000262 C-AL;100UF,20%,160V,GP,16X25MM,5MM,
C807 2201-000599 C-CERAMIC,DISC;560PF,10%,500V,
C808 2301-000016 C-FILMPEF;22NF,5%,100V,TP,7.2X
C809 2401-001998 C-AL;1000UF,20%,25V,GP,TP,10X20
C810 2305-000412 C-FILM,MPEF;470NF,5%,63V,-,5MM
C812 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1
C813 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C814 2306-000318 C-FILM,MPPF;220NF,20%,250V,-,2
C815 2401-000223 C-AL;100NF,20%,50V,LL,5X11MM,5MM,TP
C816 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M
C817 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1
C819 2201-000963 C-CERAMIC;CK45Y5U400VACT102-MH
C820 2401-001998 C-AL;1000UF,20%,25V,GP,TP,10X20
C821 2401-001486 C-AL;47UF,20%,160V,HR,13X20MM,5MM,T
C822 2301-000192 C-FILM,PEF;1NF,5%,50V,5.3X10MM
C823 2201-000370 C-CERAMIC,DISC;220PF,10%,50V,Y5P,TP
C851 2401-001571 C-ELECTROLYTIC;CE04WTAPG50V47C852 2301-000310 C-FILM,PEF;68NF,5%,50V,8.0X8.5
C901 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C902 2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50
C903 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M
C904 2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50
C905 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4
C907 2401-000027 C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA
C908 2201-000193 C-CERAMIC,DISC;10PF,0.25PF,50V
C909 2201-000573 C-CERAMIC,DISC;47PF,5%,50V,NPO
C911 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M
C912 2301-000310 C-FILM,PEF;68NF,5%,50V,8.0X8.5
C914A 2401-000962 C-AL;22uF,20%,50V,GP,TP,5x11,5
C915 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2
CE01 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M
CLW/HS AA65-30104C CLAMP-WIRE;NYLON 66,V2,NTR,W1 Z4,ALL MOD
CN501 L6434-0084-000 CONNECTORASSY;B8XB8400MM1007#26
CN603 3711-002642 POST-HEADER;67094-003(AUTO)
CN701 3711-002646 POST-HEADER;67094-007(AUTO)
CN704 L6434-0010-040 CONNECTORASSY;B7XS7150MM1007#2
CORD/H AA61-20284A HOLDER P CORD;PP,VO,BLK,KE-002
CORD/P AA39-10007Y POWER-CORD;-,EP2/YES,SPT-2 18AWGx2C,2.4m
CU02 2305-000665 C-FILM;CF922N63VT104-J-40/1053
CU10 2401-000832 C-AL;220UF,20%,25V,GP,8X11MM,5
CX01 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2
CX02 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M
CX03 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M
CX04 2201-000556 C-CERAMIC,DISC;470PF,10%,500V,
D101 0403-000700 DIODE-ZENER;TZP33A,33V,31-35V,
D102 0403-000296 DIODE-ZENER;EQA02-06A/MTZ5.6B(
D103 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41
D201 0403-000663 DIODE-ZENER;MTZ3.3B,3.3V,3.32D202 0401-000005 DIODE;1N4148TAPG
D203 0401-000005 DIODE;1N4148TAPG
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
7-17 TXJ1996
!
!!!
!
!
Page 34
!
Electric Parts List
Samsung Electronics 7-11
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
D204 0401-000005 DIODE;1N4148TAPG
D205 0403-000355 DIODEZENER;UZ5.1BSB,4.97~5.17V,0.5UA,500
D206 0401-000005 DIODE;1N4148TAPG
D207 0401-000005 DIODE;1N4148TAPG
D208 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41
D210 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57D299 0403-000654 DIODE-ZENER;MTZ12,12V,11.4-12.
D301 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40
D302 0403-000654 DIODE-ZENER;MTZ12,12V,11.4-12.
D401 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41
D402 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41
D403 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40
D404 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40
D405 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40
D407 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40
D601 0401-000005 DIODE;1N4148TAPG
D701 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57D703 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57D704 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57D802 0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5
D803 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40
D805 0402-000213 DIODE-RECTIFIER;ERB12-06,600V,
D806 0401-000005 DIODE;1N4148TAPG
D807 0402-000213 DIODE-RECTIFIER;ERB12-06,600V,
D808 0402-000213 DIODE-RECTIFIER;ERB12-06,600V,
D809 0402-000213 DIODE-RECTIFIER;ERB12-06,600V,
D810 0402-000213 DIODE-RECTIFIER;ERB12-06,600V,
D814 0402-000534 DIODE-RECTIFIER;RG10V,400V,1.5
D855 0403-000296 DIODE-ZENER;EQA02-06A/MTZ5.6B(
D856 0403-000296 DIODE-ZENER;EQA02-06A/MTZ5.6B(
D901 0401-000005 DIODE;1N4148TAPG
D902 0403-000296 DIODE-ZENER;EQA02-06A/MTZ5.6B(
D903 0401-000005 DIODE;1N4148TAPG
D904 0401-000005 DIODE;1N4148TAPG
D905 0403-000296 DIODE-ZENER;EQA02-06A/MTZ5.6B(
D906 0403-000296 DIODE-ZENER;EQA02-06A/MTZ5.6B(
DU01 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41
DX01 0403-000297 DIODE-ZENER;EQA02-06D/MTZ6.2B(
DX02 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41
DZ601 0403-000654 DIODE-ZENER;MTZ12,12V,11.4-12.
DZ801 1405-000152 VARISTOR;560V,2500A,14X8.5MM,T
DZ802 0403-000300 DIODE-ZENER;MTZ8.2B,7.78-.19V,
DZ803 0403-000296 DIODE-ZENER;EQA02-06A/MTZ5.6B(
DZ804 1405-000152 VARISTOR;560V,2500A,14X8.5MM,T
DZ806 0403-000294 DIODE-ZENER;MTZ4.7B,4.55-4.80V,500MV,D0DZ807 0403-000297 DIODE-ZENER;EQA02-06D/MTZ6.2B(
DZ901 0403-000296 DIODE-ZENER;EQA02-06A/MTZ5.6B(
DZ902 0403-000296 DIODE-ZENER;EQA02-06A/MTZ5.6B(
DZ903 0403-000355 DIODEZENER;UZ5.1BSB,4.97~5.17V,0.5UA,500
F801 3601-000144 FUSE-FERRULE;125V,4A,SLOWBLOW,
F801A 3602-000114 FUSE-HOLDER;-,-,30MOHM
F801B 3602-000114 FUSE-HOLDER;-,-,30MOHM
GT101A AA39-20010D LEAD-CONNECTOR,ASSY;-,YFH800-01,S,1P,400
IC201 1204-001296 IC-CHROMA;KA2163B,DIP,56P,-,PL
IC301 1204-000475 IC;KA2131 H/SINK
IC601 1201-001298 IC-POWER AMP;4425,SIP,5P,9.5MIL,MONO,45D H/SINK
IC801 1203-001493 IC-PEM CONTROLLER;3S0765RF,TO3PF-5L,5,21 H/SINK
IC802 1203-000576 IC-S/WREGU;TDA8139SIP7POUT-9.5
IC901 AA13-30020A IC-MCU;-,Z8933412PSC-R3757,16BIT,SDIP
IC902 1103-001107 IC-EEPROM;24C020,256X8BIT,DIP,8P,300MIL
JA601 3722-000143 JACK-PHONE;1P,3.4MM,-,MBAG
JA701 3722-000162 JACK-PIN;2P,3.4MM,-,SN
JA703 3722-000184 JACK-RCA;2P,3.4MM,-,AG
L102 2701-000207 INDUCTOR-AXIAL;56UH,5%,2.5X3.4
L152 2701-000202 INDUCTOR-AXIAL;560NH,10%,2.5X3
L201 AA26-10004K TRANS-IF;-,7MG,SIF,-,7MM,100PF
L202 2701-000207 INDUCTOR-AXIAL;56UH,5%,2.5X3.4
L203 2701-000158 INDUCTOR-AXIAL;22UH,10%,2.5X3.
L204 2701-000207 INDUCTOR-AXIAL;56UH,5%,2.5X3.4
L205* AA26-10004C TRANS-IF;-,7MG,VIF,0.37UH,7MM,
L206 2701-000111 INDUCTOR-AXIAL;100UH,10%,2.5X3
L208 2701-000114 INDUCTOR-AXIAL;10UH,10%,2.5X3.
L301 2701-000116 INDUCTOR-AXIAL;10UH,10%,4.2X9.
L401 AA27-30001B COIL-LINEARITY;-,195UH,QIC1010
L402 2701-001032 INDUCTOR-AXIAL;100UH,10%,5X14MM
L501 2701-000184 INDUCTOR-AXIAL;4.7UH,10%,2.5X3.4MM
L502 2701-000184 INDUCTOR-AXIAL;4.7UH,10%,2.5X3.4MM
L503 2701-000184 INDUCTOR-AXIAL;4.7UH,10%,2.5X3.4MM
L602 2701-000158 INDUCTOR-AXIAL;22UH,10%,2.5X3.
L801 AA29-30001R FILTER-LINE;-,6MH,2.0A,-,SQ191
L802 3301-000287 CORE-FERRITEBEAD;AA,3.5X1.0X6.
L803 2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,L804 3301-000287 CORE-FERRITEBEAD;AA,3.5X1.0X6.
L810 AA27-10002Y COIL-CHOKE;-,100UH,K,10,700MA,
L811 2901-000299 FILTER-EMIBEAD;BL02RN2-R65T2DB
L901 2701-000197 INDUCTOR-AXIAL;5.6UH,10%,2.5X3
L902 2701-000114 INDUCTOR-AXIAL;10UH,10%,2.5X3.
L910 2901-000299 FILTER-EMIBEAD;BL02RN2-R65T2DB
L999 2701-000115 INDUCTOR-AXIAL;10UH,10%,2.8X7M
LD901 AA96-30007A ASSY-LED,GUIDE;AA61-50055A,DL-G7GA,GREEN
NT801 1404-000187 THERMISTOR;KL11L4R7-3.5A4.7OHM
P801A 1404-000208 POSISTOR;PTH631D02BF7ROM140TDE
PC802 0604-001038 PHOTOCOUPLER;TR,130-260%,200MW
PWR/AC AA96-20129A ASSY-POWER,CORD;-,EP2/YES,H/C300,ME301P,
Q151 0501-000436 TR-SMALLSIGNAL;KTC3197,NPN,30V
Q201 0501-002183 TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100
Q202 0501-002183 TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100
Q203 0501-002183 TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100
Q401 0502-001160 TR-POWER;2SD2499,NPN,50000mV,T0-3P,BK,8
Q402 0501-000369 TRANSISTOR;KSC2331-Y(TAPG)
Q501 0501-002014 TR-SMALLSIGNAL;KSC2330-RNPN
Q502 0501-002014 TR-SMALLSIGNAL;KSC2330-RNPN
Q503 0501-002014 TR-SMALLSIGNAL;KSC2330-RNPN
Q601 0502-000242 TR-POWER;KSA614,PNP,-80V,-55V,
Q602 0501-002183 TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100
Q801 1203-001217 IC-POST,ADJUSTREG;431,T0-92,3P,4.58MIL,P
Q902 0501-002183 TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100
Q903 0501-002183 TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100
QU01 0504-000123 TR-DIGITAL;KSR1010,NPN,300MW,1
QU10 0501-000369 TRANSISTOR;KSC2331-Y(TAPG)
QX01 0501-000283 TRANSISTOR;KSA539-Y(TAPG)/YTAM
R101 2001-000812 R-CARBON;5.6Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R102 2001-001000 R-CARBON ;82Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R104 2003-000592 R-METALOXIDE(S);22OHM,5%,2W,AD
R105 2003-000592 R-METALOXIDE(S);22OHM,5%,2W,AD
R106 2003-000664 R-METAL OXIDE(S);330HM,5%,2W,AF,TP,4X12M
R107 2003-000664 R-METAL OXIDE(S);330HM,5%,2W,AF,TP,4X12M
R152 2001-000221 R-CARBON;1.2KOHM,5%,1/8W,AA,TP
R153 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP
R154 2001-000780 R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm
R155 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,
R156 2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,1
R157 2001-000568 R-CARBON;27OHM,5%,1/8W,AA,TP,1
R158 2001-000007 R-CARBON;3KOHM,5%,1/8W,AA,TP,1
R159 2001-000007 R-CARBON;3KOHM,5%,1/8W,AA,TP,1
R201 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R202 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP
R203 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP
R204 2001-000221 R-CARBON;1.2KOHM,5%,1/8W,AA,TP
R205 2001-000221 R-CARBON;1.2KOHM,5%,1/8W,AA,TP
R206 2001-000221 R-CARBON;1.2KOHM,5%,1/8W,AA,TP
R207 2001-001111 R-CARBON(S);240OHM,5%,1/2W,AA,
R208 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,
R209 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,
R210 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,
R211 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,
R212 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,
R213 2001-000837 R-CARBON;51KOHM,5%,1/8W,AA,TP,
R214 2001-000331 R-CARBON;12KOHM,5%,1/8W,AA,TP,
R215 2001-000331 R-CARBON;12KOHM,5%,1/8W,AA,TP,
R218 2001-000591 R-CARBON;3.3KOHM,5%,1/8W,AA,TP
R219 2001-000674 R-CARBON;360OHM,5%,1/8W,AA,TP,
R222 2001-000773 R-CARBON;470KOHM,5%,1/8W,AA,TP
R223 2001-000780 R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm
R226 2001-000508 R-CARBON;220KOHM,5%,1/8W,AA,TP
R227 2001-000508 R-CARBON;220KOHM,5%,1/8W,AA,TP
R228 2001-000258 R-CARBON;1.8Kohm,5%,1/8W,AA,TP,1.8x3.2m
R229 2001-000258 R-CARBON;1.8Kohm,5%,1/8W,AA,TP,1.8x3.2m
R230 2001-000591 R-CARBON;3.3KOHM,5%,1/8W,AA,TP
R231 2001-000660 R-CARBON;33KOHM,5%,1/8W,AA,TP,
R233 2004-001234 R-METAL;75KOHM,5%,1/8W,AA,TP,1
R234 2001-000405 R-CARBON;180OHM,5%,1/8W,AA,TP,
R235 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP
R236 2001-000548 R-CARBON;270KOHM,5%,1/8W,AA,TP
!!!!!
!!!
!!!!!
!!!
Page 35
Electric Parts List
7-12 Samsung Electronics
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
R237 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,
R239 2001-000947 R-CARBON;7.5KOHM,5%,1/8W,AA,TP
R240 2001-000577 R-CARBON;2KOHM,5%,1/8W,AA,TP,1
R241 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R242 2001-000221 R-CARBON;1.2KOHM,5%,1/8W,AA,TP
R251 2001-000591 R-CARBON;3.3KOHM,5%,1/8W,AA,TP
R252 2001-000591 R-CARBON;3.3KOHM,5%,1/8W,AA,TP
R253 2001-000591 R-CARBON;3.3KOHM,5%,1/8W,AA,TP
R257 2008-000252 R-FUSIBLE(S);0.47OHM,10%,1/2W,
R301 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R302 2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,
R303 2001-000908 R-CARBON ;62Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R304 2003-000436 R-METALOXIDE(S);1.5OHM,5%,1W,A
R305 2001-000947 R-CARBON;7.5KOHM,5%,1/8W,AA,TP
R306 2001-000766 R-CARBON;43KOHM,5%,1/8W,AA,TP,
R307 2001-000864 R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R308 2001-000908 R-CARBON ;62Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R309 2003-001043 R-METALOXIDE(S);510OHM,5%,1W,A
R401 2001-000780 R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm
R402 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,
R403 2001-001114 R-CARBON(S);270OHM,5%,1/2W,AA,
R404 2001-001165 R-CARBON(S);56OHM,5%,1/2W,AB,T
R405 2003-000540 R-METALOXIDE(S);1KOHM,5%,2W,AD
R406 2003-001024 R-METALOXIDE(S);150OHM,5%,2W,A
R406A 2003-001024 R-METALOXIDE(S);150OHM,5%,2W,A
R407 2003-000994 R-METALOXIDE(S);33KOHM,5%,2W,AF,TP,3.9X1
R408 2004-001390 R-METAL(S);1KOHM,2%,1/2W,AA,TP
R409 2008-000253 R-FUSIBLE(S);0.47OHM,5%,1W,AF,
R410 2008-000206 R-FUSIBLE(S);1OHM,5%,1/2W,AF,T
R411 2004-001373 R-METAL,FILM;RM1/2T100K-F
R412 2004-001373 R-METAL,FILM;RM1/2T100K-F
R415 2003-000755 R-METALOXIDE(S);6.8KOHM,5%,2W,AD,TP,4X12
R416 2001-000022 R-CARBON(S);33OHM,5%,1/2W,AA,T
R417 2001-001410 R-CARBON;RD1/2T(S)430-J43R
R444 2001-001099 R-CARBON/METALFILM;RD1/2T2.7KR501 2001-000007 R-CARBON;3KOHM,5%,1/8W,AA,TP,1
R502 2001-000007 R-CARBON;3KOHM,5%,1/8W,AA,TP,1
R503 2001-000007 R-CARBON;3KOHM,5%,1/8W,AA,TP,1
R504 2003-000784 R-METAL OXIDE(S);7.5KOHM,5%,2W,AF,TP,3.7
R504A 2003-000784 R-METAL OXIDE(S);7.5KOHM,5%,2W,AF,TP,3.7
R505 2003-000784 R-METAL OXIDE(S);7.5KOHM,5%,2W,AF,TP,3.7
R505A 2003-000784 R-METAL OXIDE(S);7.5KOHM,5%,2W,AF,TP,3.7
R506 2003-000784 R-METAL OXIDE(S);7.5KOHM,5%,2W,AF,TP,3.7
R506A 2003-000784 R-METAL OXIDE(S);7.5KOHM,5%,2W,AF,TP,3.7
R507 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,
R508 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,
R509 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,
R510 2001-000628 R-CARBON;300OHM,5%,1/8W,AA,TP,
R511 2001-000628 R-CARBON;300OHM,5%,1/8W,AA,TP,
R512 2001-000628 R-CARBON;300OHM,5%,1/8W,AA,TP,
R513 2001-000666 R-CARBON;33OHM,5%,1/8W,AA,TP,1
R514 2001-000666 R-CARBON;33OHM,5%,1/8W,AA,TP,1
R515 2002-001006 R-COMPOSITION;RC1/2T4.7KK/ERCR517 2001-000666 R-CARBON;33OHM,5%,1/8W,AA,TP,1
R518 2008-000266 R-FUSIBLE(S);1OHM,5%,2W,AF,TP,
R599 2008-000226 R-FUSIBLE;22OHM,5%,1/2W,AA,TP,4.7X11MM
R602 2001-000786 R-CARBON;47KOHM,5%,1/8W,AA,TP,
R603 2001-000786 R-CARBON;47KOHM,5%,1/8W,AA,TP,
R604 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP
R605 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,
R610 2001-000577 R-CARBON;2KOHM,5%,1/8W,AA,TP,1
R611 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R614 2001-001152 R-CARBON/METALFILM;RD1/2T47K-J
R615 2001-001088 R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4
R701 2001-001187 R-CARBON(S);75OHM,5%,1/2W,AA,T
R702 2001-000085 R-CARBON(S);100KOHM,5%,1/2W,AA
R703 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP
R801 2001-001150 R-CARBON(S);470KOHM,5%,1/2W,AA
R802 2003-002119 R-METAL OXIDE(S);36KOHM,5%,1W,AF,TP,2.5X
R803 2003-002008 R-METAL OXIDE(S);18KOHM,5%,2W,AF,TP,3.9X
R804 0403-000555 DIODE-ZENER;MTZ30D,30V,29.02-3
R805 2002-001013 R-COMPOSITION;4.7MOHM,10%,1/2W,AA,TP,3.7
R806 2001-001071 R-CARBON(S);12KOHM,5%,1/2W,AA,
R807 2001-001071 R-CARBON(S);12KOHM,5%,1/2W,AA,
R808 2001-001150 R-CARBON(S);470KOHM,5%,1/2W,AA
R809 2008-000205 R-FUSIBLE(S);10OHM,5%,1/2W,AF,
R811 2001-001170 R-CARBON(S);6.8OHM,5%,1/2W,AB,
R812 2008-000252 R-FUSIBLE(S);0.47OHM,10%,1/2W,
R813 2008-001058 R-FUSIBLE(S);0.18OHM,10%,1W,AF
R814 2001-001135 R-CARBON(S);36KOHM,5%,1/2W,AA,
R815 2004-001408 R-METAL(S);91KOHM,1%,1/2W,AA,T
R816 2001-001134 R-CARBON(S);360OHM,5%,1/2W,AA,TP,2.4X6.4
R817 2001-001134 R-CARBON(S);360OHM,5%,1/2W,AA,TP,2.4X6.4
R818 2001-001134 R-CARBON(S);360OHM,5%,1/2W,AA,TP,2.4X6.4
R819 2008-001011 R-FUSIBLE(S);0.18OHM,10%,2W,AF
R821 2004-004089 R-METAL;123KOHM,1%,1/2W,AA,TP,2.5X6.5
R822 2001-000022 R-CARBON(S);33OHM,5%,1/2W,AA,T
R823 2001-001178 R-CARBON(S);680OHM,5%,1/2W,AA,
R824 2001-001125 R-CARBON(S);300KOHM,5%,1/2W,AA
R852 2001-001088 R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4
R853 2001-001054 R-CARBON(S);1.6KOHM,5%,1/2W,AB,TP,2.4X6.
R854 2004-001983 R-METAL;2.49KOHM,1%,1/2W,AA,TP,2.4X6.4
R901 2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,1
R902 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R903 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,
R904 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,
R905 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R906 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP
R907 2001-000995 R-CARBON;820OHM,5%,1/8W,AA,TP,
R908 2001-000232 R-CARBON;1.3KOHM,5%,1/8W,AA,TP
R910 2001-000995 R-CARBON;820OHM,5%,1/8W,AA,TP,
R911 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,
R913 2001-000924 R-CARBON;680ohm,5%,1/8W,AA,TP,1.8x3.2mm
R914 2001-000577 R-CARBON;2KOHM,5%,1/8W,AA,TP,1
R915 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP
R916 2001-000947 R-CARBON;7.5KOHM,5%,1/8W,AA,TP
R917 2001-000947 R-CARBON;7.5KOHM,5%,1/8W,AA,TP
R918 2001-000947 R-CARBON;7.5KOHM,5%,1/8W,AA,TP
R919 2001-000977 R-CARBON;8.2Kohm,5%,1/8W,AA,TP,1.8x3.2m
R920 2001-000522 R-CARBON;22KOHM,5%,1/8W,AA,TP,
R921 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,
R922 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,
R923 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,
R924 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP
R925 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP
R926 2001-000008 R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R927 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,
R928 2001-000864 R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R929 2001-000232 R-CARBON;1.3KOHM,5%,1/8W,AA,TP
R930 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,
R931 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R932 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,
R933 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,
R934 0401-000005 DIODE;1N4148TAPG
R937 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,
R938 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R940 2001-000708 R-CARBON;39OHM,5%,1/8W,AA,TP,1.8X3.4MM
R951 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP
R952 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP
R988 2001-000508 R-CARBON;220KOHM,5%,1/8W,AA,TP
RE01 2001-000117 R-CARBON(S);68ohm,5%,1/2W,AA,TP,2.4x6.4m
RE02 2001-000117 R-CARBON(S);68ohm,5%,1/2W,AA,TP,2.4x6.4m
RH01 2002-001006 R-COMPOSITION;RC1/2T4.7KK/ERCRH02 2002-001006 R-COMPOSITION;RC1/2T4.7KK/ERCRLU01 3501-001040 RELAYPOWER;12VDC,500MW,10A,1FO
RM901 AA59-60001U MODULE-REMOCON;-,ORC-50VF,38KH
RU01 2002-001010 R-COMPOSITION;1.8MOHM,10%,1/2W,AA,TP,3
RU02 2001-000780 R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm
RU06 2001-000397 R-CARBON;180KOHM,5%,1/8W,AA,TP
RU07 2001-001062 R-CARBON(S);10MOHM,5%,1/2W,AA,
RU10 2001-000924 R-CARBON;680ohm,5%,1/8W,AA,TP,1.8x3.2mm
RU11 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,
RU12 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP
RU13 2001-000022 R-CARBON(S);33OHM,5%,1/2W,AA,T
RX01 2001-000397 R-CARBON;180KOHM,5%,1/8W,AA,TP
RX02 2001-000411 R-CARBON;18KOHM,5%,1/8W,AA,TP,
RX03 2004-001987 R-METAL;4.3KOHM,1%,1/2W,AA,TP,
RX04 2004-001376 R-METAL(S);11KOHM,1%,1/2W,AA,T
RX05 2001-000522 R-CARBON;22KOHM,5%,1/8W,AA,TP,
RX08 2001-000837 R-CARBON;51KOHM,5%,1/8W,AA,TP,
SF101 2904-000304 FILTER-SAW;M1859MNTSC/USAVIFST
SW901 3404-000244 SWITCH-TACT;15V,20MA,90-170GF,
SW902 3404-000244 SWITCH-TACT;15V,20MA,90-170GF,
SW903 3404-000244 SWITCH-TACT;15V,20MA,90-170GF,
!!!
!
!
Page 36
Electric Parts List
Samsung Electronics 7-13
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
SW904 3404-000244 SWITCH-TACT;15V,20MA,90-170GF,
SW905 3404-000244 SWITCH-TACT;15V,20MA,90-170GF,
SW906 3404-000295 SW-TACT,V;KPT1122R1KEYSTT=0.3M
T401 AA26-50001B HORIZ.DRIVE;-,7.1MH,102UH,10-2
T444 AA26-30001Y TRANS-FRYBACK;-,FSV-20A001,20,125V
T801 AA26-20007L TRANS-SWITCHING;120V,125/12.5,UL/CSA,EAE
TU01 AA40-10006U TUNER-F/S;TECC1070PG31A(S)
V999 3704-001090 SOCKET-CRT;9P,15.24PI,26.5PI,SN
X201 2801-000226 CRYSTAL-UNIT;3.579545MHZ,20PPM
X202 2802-000172 RESONATOR-CERAMIC;503.5KHZ,0.5
X901* 2801-003224 CRYSTAL-UNIT;32.768KHZ,20PPM,2
Z201 2903-001022 FILTER-CERAMIC;TR,4.5MHZ
Z601 2903-000135 FILTER-CERAMIC;BP,4.5MHZ
ASSY-CRT
A/CRTP AA94-50014I ASSY-CRT;A48KRD82X(H)+380MG,SEMTNT.BZIL
CRT LB03-10029W CRT-COLOR;A48KRD82X(H)+380MG,SEMTNT.BZIL
C-Y AA27-00002A MAGNET-CONVERGENCE;JH291-SC-OB,29.1M
D-Y AA27-50004W -,DSE-1992LL(1H),20’/A48KRD82X
S-GUM AA63-60004G SPACER-GUM,CRT;-,NTRRUBBER,T3.
SPACER AA63-60028A SPACER-DY;-,NEOPRENE,-,BLK,V0W
ASSY-ACCESSORY
A/ACCS AA97-20009E ASSY-ACCESSORY;TM58,BLK,W-ANT,USA
A/ROD AA42-00001A ANT-ROD;-,3S,650MM,ABS,UL/CSA TXJ1996
I/B AA68-11252D INSTRCTION-BOOK;K15A,ENG,TM58-9,205X150 TXJ1996
L7000-0132 ANT-RODVHF;4SDODIPOLE850MMBRN TXJ1966
AA68-11252A INSTRCTION-BOOK;K15A,FRENCH,TM59,205X150 TXJ1966
ASSY-CLAMPERS
A/CLMP L9100-000-005 ASSY-CLAMPERS;K15A,19,;F/V
AC+BC AA65-30008A CLAMP-CORD;-,PE,HB,BLK,-,-
FBT AA65-30109A CLAMP-FBT;NYLON-66,V2,BLK,-,-,CWIRE1 AA65-30018A CLAMP-WIRE;-,NYLON6.6,-,-,DATL
CWIRFC AA65-30105A CLAMP-WIRE;NYLON 66N,VO,NTR,15MM
CDCOIL L9400-0001 HOLDER-DEGAUSSING;25POLYVINYLCHLORIDEFL
REMOCON
RMT AA59-10102B REMOCON;DP,TM58,AA59-10100B, TXJ1996
RMT AA59-10101M REMOCON; DP,TM59,-,-,AA59-10095T TXJ1966
ASSY-CABINET
A/BACK AA92-10034BA ASSY-CABINET,(COM);TXH1966,9,VO,S/V,K15A
CB+CF 6002-000514 SCREW-TAPPING;RH,+,2,M4,L15,ZP
B/C AA64-00154B CABINET-BACK;-,20F2 R1,-,HIPS,V0,BLK,-,-
ASSY-CABINET,FRONT
A/FRNT AA92-30161NA ASSY-CABINET,FRONT;TXJ1966,9,VO,S/V,K15A
SPK+CF 6002-000514 SCREW-TAPPING;RH,+,2,M4,L15,ZP
PA+CF AA60-10002A SCREW-TAPPING;-,RH,+,M4,L12,ZP
STOPPER AA61-40113A STOPPER-PCB;-,ABS,HB,NTR.
BADGE AA64-70127F BADGE-BRAND;AL,SS,SILVER,R800
D-COIL AA27-20004B COIL-DEGAUSSING;-,20,5.7ohm,30T,L2170,E
CRT+CF AA60-10050R SCREW-ASSY;WC,HH,+M5,L31.5,SWR
ASSY-SPEAKER
A/SPK AA96-10141A ASSY-SPEAKER;3W,8OHMX1,700
SPK 3001-001020 SPEAKER;3W,8ohm,90dB,140Hz
L/SPK AA39-20501C LEAD CONNECTOR-ASSY;-,67096-003,REC,3(2)
CABINET-FRONT
F/C AA64-00152A CABINET-FRONT;20F2,BK708P,HIPS,V0,BLK
INDLED AA64-00158B INDICATOR-LED;20F2,ACRYL,CLR,
KNOCON AA64-00155B KNOB-CONTROL;-,20F2,-,ABS,HB,BLK
KNOPOW AA64-00156B KNOB-POWER;-,20F2,NO-SILK,ABS,HB,BLK
WR+CF 6002-000512 SCREW-TAPPING;RH,+,2,M4,L12,ZP
IL+CF 6002-000512 SCREW-TAPPING;RH,+,2,M4,L12,ZP
SPRING AA61-60003J SPRING-CS;-,-,SUS304,0.5,OD6,H
WINDOW AA64-00157B WINDOW-REMOCON;-,20F2,-,PC,VO,VIOLET,-
!!!
!
!
!
Page 37
7-14 Samsung Electronics
MEMO
Page 38
8. Block Diagram
Block Diagram
Samsung Electronics 8-1
IC601
SOUND-AMP
2.5W x 1CH
LA4425
R.G.B
CRT
1CHIP
IF/V/C/D
KA2163B
SAW
M1859M
TU01*
TUNER
TELH9-212A
IC902
EEPROM
KS24C020
IC901*
MICOM
SZM-354ET
EXT IN
VIDEO
EXT IN
AUDIO
IC201
Q401*
H-TR
KSC5368
VERTICAL-AMP
KA2131
T444*
F.B.T
14" : FSV14A001
20" : FSV20A001
21" : FSV20A001
IC802
MULTI-REGULATOR
KA7631
SWITCHING
TRANS
S:125V,12.5V
T801*
D807 ~ D810
IC801*
SPS CONTROL
KA3SO680
KA3S0765
(125V)
(12.5V)
MICOM
1CHIP
(5V)
(9V)
I2C BUS
PC802
PHOTO
COULPER
DUAL
Page 39
9. PCB Layout
9-1 PCB-MAIN
PCB Layout
Samsung Electronics 9-1
D101 53 150
D102 56 130
D103 71 141
D201 135 196
D202 96 105
D203 96 107
D204 96 110
D205 123 92
D206 114 95
D207 114 97
D208 115 74
D210 99 105
D299 99 212
D301 32 139
D302 31 146
D401 85 99
D402 70 98
D403 59 74
D404 72 53
D405 81 38
D407 58 105
D601 124 213
D701 130 136
D702 227 203
D703 210 238
D704 85 159
D802 104 11
D803 150 23
D804 92 183
D805 168 42
D806 150 27
D807 186 51
D808 193 54
D809 186 67
D810 196 66
D814 99 60
D855 157 100
D856 147 101
D901 160 119
D902 163 110
D903 171 130
D904 132 96
D905 231 179
D906 157 131
DL01 105 219
DL02 108 219
DU01 211 118
DX01 116 107
DX02 111 101
DZ801 215 20
DZ802 179 30
DZ803 178 24
DZ806 157 17
DZ807 150 20
DZ901 231 83
DZ902 231 156
DZ903 203 124
IC201 100 164
IC301 50 132
IC601 146 225
IC602 168 221
IC801 155 10
IC802 141 97
IC901 215 153
IC902 219 178
ICK01 69 213
Q151 61 183
Q201 107 129
Q202 101 140
Q203 99 144
Q401 24 85
Q402 63 118
Q501 24 197
Q502 32 197
Q503 12 195
Q601 145 203
Q602 132 223
Q801 100 29
Q902 119 226
Q903 87 115
QL01 80 237
QL03 115 226
QLK1 106 229
QU01 197 173
QU10 195 115
QX01 112 113
Loc. No. X Y
DIODE
IC
Loc. No. X Y
TRANSISTOR
Page 40
10. Wiring Diagram
Wiring Diagram
Samsung Electronics 10-1
CRT PCB
B
G
R
9V
GND
180V
GND
HT
B
G
R
9V
GND
180V
GND
HT
CN501
CN201
A/V ASSY
V1
R+
RV0
GND
AI
CN702
CN701
A0
V1
R+
R-
V0
GND
AI
A0
S
G
SPEAKER
CN601
MAIN ASSY
CRT
H1
H2
V1
V2
CN401
H1
H2
V1
V2
CRT PCB
CN501
S
G
Page 41
11. Schematic Diagrams
11-1 MAIN 1/4
Schematic Diagrams
Samsung Electronics 11-1
: Power Line
: Signal Line
Page 42
TP13
IC201 30PIN
TP15
TP17
TP21
TP10
TP11
TP19
IC201 37PIN
IC201 43PIN
IC201 47PIN
IC201 53PIN
IC201 25PIN
IC201 27PIN
TP7
TP8
IC201 23PIN
IC201 22PIN
TP14
IC201 32PIN
TP16
TP18
TP12
TP20
IC201 41PIN
IC201 45PIN
IC201 49PIN
IC201 28PIN
TP9
IC201 24PIN
TP4
TP5
IC201 20PIN
IC201 19PIN
TP6
IC201 21PIN
TP1
TP2
IC201 4 PIN
IC201 2 PIN
TP3
IC201 7PIN
Schematic Diagrams
11-2 Samsung Electronics
TP9
TP10
TP13
TP14
TP15
TP16
TP17
TP18
TP21
TP19
TP20
TP1
TP2
TP3
TP4
TP5
TP6
TP7
TP8
TP11
TP12
11-2 MAIN 2/4
: Power Line
: Signal Line
Page 43
Schematic Diagrams
Samsung Electronics 11-3
TP25
TP27
TP26
TP24
11-3 MAIN 3/4
TP24
TP26
TP25
IC801 1 PIN
TP27
T444 10 PIN
: Power Line
Page 44
Schematic Diagrams
11-4 Samsung Electronics
11-4 MAIN 4/4
: Power Line
: Signal Line
Loading...