Samsung HW-C779S User Manual
HW-C700
HW-C700B
HW-C770S
HW-C779S
HW-C770BS
AV Receiver System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
HW-C700-C770S-C770BS-ELS_0309.in1 1HW-C700-C770S-C770BS-ELS_0309.in1 1 2010-03-09 10:10:242010-03-09 10:10:24
Safety information
SAFETY WARNINGS
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates “dangerous voltage”
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING : To reduce the risk of fi re or electric shock, do not expose this appliance to rain or moisture.
inside the product that presents a risk of
electric shock or personal injury.
This symbol indicates important instructions
accompanying the product.
CAUTION :
This apparatus shall always be connected to a AC outlet with a protective grounding connection.
•
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the
•
mains plug shall be readily operable.
CAUTION
Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, shall be
•
placed on the apparatus.
The Mains plug is used as a disconnect device and shall stay readily operable at any time.
•
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Wiring the Main Power Supply Plug (UK Only)
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on
the pin face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the
same colour as the fuse fitted in the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you
should obtain a suitable safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect
the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord.
Never attempt to insert bare wires directly into a mains socket. A plug and fuse must be used at all times.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:– BLUE = NEUTRAL BROWN = LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK.
The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING : DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE
LETTER E OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW.
2
HW-C700-C770S-C770BS-ELS_0309.in2 2HW-C700-C770S-C770BS-ELS_0309.in2 2 2010-03-09 10:11:182010-03-09 10:11:18
PRECAUTIONS
2.7 inches
3.9 inches
3.9 inches
3.9 inches
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install your
player horizontally, on a suitable base (furniture), with enough space around it for ventilation (7.5~10cm). Make sure the
ventilation slots are not covered. Do not stack anything on top of the amplifier. In order to disconnect the player completely from the
power supply, remove the AC plug from the wall outlet, especially when left unused for a long period of time.
ENG
During thunderstorms, disconnect the AC plug from the
wall outlet.
Voltage peaks due to lightning could damage the unit.
Phones
Protect the player from moisture(i.e. vases), and excess
heat(e.g.fireplace) or equipment creating strong magnetic or
electric fields (i.e.speakers...). Disconnect the power cable
from the AC supply if the player malfunctions. Your player is
not intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc have been
stored in cold temperatures.
If transporting the player during the winter, wait
approximately 2 hours until the unit has reached room
temperature before using.
Do not expose the unit to direct sunlight or other heat
sources.
This could lead to overheating and malfunction of
the unit.
The batteries used with this product contain chemicals
that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
3
HW-C700-C770S-C770BS-ELS_0309.in3 3HW-C700-C770S-C770BS-ELS_0309.in3 3 2010-03-09 10:11:182010-03-09 10:11:18
Features
Digital AV Receiver
This product is a pure digital AV receiver that performs digital
signal processing to minimize signal distortion and loss.
Dolby Pro Logic llx
Dolby Pro Logic IIx is a new technology that provides
discrete 7.1 channels out of 2 channel or multi channel
sources.It also provides Music,Movie and Game modes.
Dolby Pro Logic IIx is an improved surround system that is
optimized to a 7.1 CH multimedia system, enabling you to
maximize your entertainment experience.
Dolby Pro Logic llz
Dolby Pro Logic IIz adds front height channels to surround
sound, creating a 7.1 playback system for video games,
home music, and movies; bringing enhanced spatial effects
and enveloping sound.
DTS 96/24
DTS 96/24 encodes standard 16 bit/44.1 kHz sound to
24 bit/96kHz and applies it to a 5.1 CH sound track.
DOLBY DIGITAL EX
Adds a surround back channel for more spacious sound
compared to regular 5.1 channel Dolby Digital.
DTS (Digital Theater Systems)
DTS provides a discrete 5.1 CH digital audio signal for both
music and movie contents and uses less compression than
Dolby Digital for richer sound.
Dolby Digital Plus
Dolby Digital Plus is the next-generation audio technology
for all high-defi nition programming and media.
Dolby True-HD
Dolby True-HD is Dolby’s next-generation lossless
technology developed for high-defi nition disc-based media.
DTS-HD (Master Audio, High Resolution)
(Digital Theater Systems - High Defi nition)
DTS-HD Audio provides the highest quality multi-channel
sound possible.
It delivers sound quality that matches the clear and vivid
images of high-defi nition video.
DTS
Provides a full range of 6 channels by converting a digital PCM
or analogue stereo signal using DTS digital matrix decoding.
iPod
You can enjoy music fi les by connecting your iPod/iPhone
to the AV Receiver with the supplied iPod dock.
SFE (Sound Field Effect) Using 32bit
Audio Digital Signal Processing
Provides more realistic surround sound with normal stereo
audio sources.
Anynet+ (HDMI-CEC) Function
Anynet+ is a function that can be used to operate this AV
Receiver with a Samsung TV remote control, by connecting
the receiver to a SAMSUNG TV using an HDMI Cable. (This
function is available only in connection with Samsung TV
and DVD player supporting Anynet+(HDMI-CEC).)
DTS-ES
(Extended Surround)
The DTS-ES (Extended Surround) system is a new multi
digital signal format that was developed by Digital Theater
Systems Inc.
Supporting full compatibility with the conventional DTS
digital surround sound format, the DTS-ES (Extended
Surround) system improves the surround signal for a 360degree surround effect.
DTS-ES adds an additional rear centre surround channel for
6.1 channel sound.
ACCESSORIES
INPUT SELECT
POWER
TV SOURCE
AMP/TV DIMMER
BD/DVD
RDS DISPLAY
TA
123
PTY- PTY SEARCH
PTY+
456
SLEEPNEO : 6
7809
PROLOGIC AUDIO ASSIGN
DSP
MUTE
TUNING
VOL
/CH
ASC
TUNER MEMORY SUBWOOFER MO/ST
SETUP/MENU
INFO
RETURN
EXIT
TVBD/DVD SAT
CD
iPod
MULTI CH VCR / AUX
Remote Control
/Batteries (AAA size) FM antenna User’s manual iPod Dock ASC microphone
4
HW-C700-C770S-C770BS-ELS_0309.in4 4HW-C700-C770S-C770BS-ELS_0309.in4 4 2010-03-09 10:11:212010-03-09 10:11:21
Contents
ENG
SAFETY INFORMATION
2
FEATURES
4
DESCRIPTION
7
CONNECTIONS
14
2 Safety Warnings
3 Precautions
● CONTENTS
4 Accessories
7 Front Panel
9 Rear Panel
10 Display
11 Insert Remote Control Batteries
11 Operation Range of the Remote Control
12 Tour of the Remote Control
14 Speaker Positioning
16 Connecting the Speakers
17 Connecting External Devices/Your TV via
HDMI
18 HDMI Function
19 Connecting to your TV
20 Connecting a DVD or BD(Blu-ray) Player
21 Connecting a Cable, Satellite or Set-top Box
22 Connecting a VCR
23 Connecting a CD Player
24 Connecting 7.1 Channel Devices
25 Connecting an iPod
27 Connecting the FM Antenna
27 Connecting Aux Components
BASIC FUNCTIONS OF YOUR AV
RECEIVER
28 Before Using the AV Receiver
28 Audio Setup
29 Selecting Digital/Analogue Input
28
5
HW-C700-C770S-C770BS-ELS_0309.in5 5HW-C700-C770S-C770BS-ELS_0309.in5 5 2010-03-09 10:11:232010-03-09 10:11:23
Contents
SETUP
30
OPERATION
45
30 Setup Menu Tree
34 Setting the Speaker Size
35 Setting the Speaker Listening Distance
36 Setting the Speaker Level
37 Setting the Test Tone
38 Setting Dolby Pro Logic Mode
38 Setting Dolby Pro Logic IIx
39 Setting Dolby Pro Logic IIz
39 Setting Tone Control
40 Setting NEO:6 Mode
41 Setting EX/ES Mode
42 AV SYNC
42 MP3 Enhancer
42 Smart Volume
43 ASC (Auto Sound Calibration) Setup
44 DRC Setup
44 HDMI Setup
44 Variable Set
45 Using the Surround Modes
46 Using the Subwoofer Selection Button
47 Listening to the Radio
48 About RDS Broadcasting
50 Using an iPod
52 Convenient Functions
53 Software Upgrade
MISCELLANEOUS
54 Operating Your TV With the Remote Control
56 Operating your DVD or BD player with the
remote control
54
TROUBLESHOOTING
57 Troubleshooting
57
APPENDIX
59 Specifi cations
59
6
HW-C700-C770S-C770BS-ELS_0309.in6 6HW-C700-C770S-C770BS-ELS_0309.in6 6 2010-03-09 10:11:232010-03-09 10:11:23
Description
FRONT PANEL
1 2 3
5 6 7
ENG
● DESCRIPTION
84 9
HEADPHONE JACK
1
AUX IN JACKS
2
ASC MIC JACK
3
DISPLAY
4
S.DIRECT/STEREO BUTTON
5
MULTI CH BUTTON
6
AV SYNC BUTTON
7
VOLUME CONTROL
8
POWER
9
10 11 1412 13
Used to connect a set of headphones.
Auxiliary AV input terminals used to connect a camcorder, portable DVD player or gaming device.
Used to connect the ASC MIC for setting up ASC (Auto Sound Calibration).
Displays the speaker/audio input status, listening mode, etc.
Used to select the S.DIRECT or STEREO mode.
Used to select a connected 7.1 multi channel player.
Used to select the Audio Delay Mode.
Adjusts the volume level.
Turns the receiver on/off.
15 16 17
18 19 20
7
HW-C700-C770S-C770BS-ELS_0309.in7 7HW-C700-C770S-C770BS-ELS_0309.in7 7 2010-03-09 10:11:232010-03-09 10:11:23
Description
FRONT PANEL
Used to select a source.
INPUT SELECT BUTTON
10
(FM BD/DVD SAT TV VCR CD AUX 7.1 MULTI CH IPOD AUDIO IPOD
VIDEO).
AUDIO ASSIGN BUTTON
11
SOUND EFFECT BUTTON
12
SETUP BUTTON
13
UP(,), DOWN(.), LEFT(<),
14
RIGHT(>) BUTTONS
ENTER BUTTON
15
TONE CONTROL
16
ASC BUTTON
17
TUNING MODE BUTTON
18
SELECT BUTTON
19
MEMORY BUTTON
20
BUTTON
Toggles to select an input mode for the selected source.
Toggles to select a surround sound mode.
Displays the SETUP menu.
Used to move the cursor up, down, left or right.
Also used to select detailed options in the SOUND EFFECT mode and to change the tone level.
Used to select an item in the SETUP menu.
Used to set the bass, treble level and tone to on/off.
Used to select the ASC (Auto Sound Calibration) mode.
Used to select the Manual or Preset mode for FM radio.
Used to change the radio frequency.
Used to set a preset radio frequency.
8
HW-C700-C770S-C770BS-ELS_0309.in8 8HW-C700-C770S-C770BS-ELS_0309.in8 8 2010-03-09 10:11:232010-03-09 10:11:23
REAR PANEL
1 2 3 4 5
ENG
● DESCRIPTION
8 9 10 18 196 7
FM ANTENNA JACK
1
MULTI CH IN JACKS
2
HDMI IN JACKS
3
HDMI OUT JACK
4
USB PORT
5
COMPONENT VIDEO IN JACKS
6
11 12 13 14
15 16 17
Connect the FM Antenna here.
Receives the analogue audio signal from an external player with a multi-channel port.
Receives digital video and audio signals simultaneously using an HDMI cable.
Outputs digital video and audio signals simultaneously using an HDMI cable.
Can be only used for fi rmware upgrades.
Receives the component video signal.
COMPONENT VIDEO OUT JACKS
7
iPod JACK
8
HW-C700-C770S-C770BS-ELS_0309.in9 9HW-C700-C770S-C770BS-ELS_0309.in9 9 2010-03-09 10:11:232010-03-09 10:11:23
Outputs the component video signal.
Receives the audio/video signal from an iPod.
9
Description
REAR PANEL
OPTICAL IN JACKS (DIGITAL AUDIO IN)
9
COAXIAL IN JACK (DIGITAL AUDIO IN)
10
VCR VIDEO IN JACK
11
VCR VIDEO OUT JACK
12
VIDEO IN JACKS
13
VIDEO OUT JACK
14
VCR AUDIO IN JACKS
15
VCR AUDIO OUT JACKS
16
AUDIO IN JACKS
17
SUBWOOFER AUDIO OUT JACKS
18
SPEAKER OUT TERMINALS
19
DISPLAY
1 2 3 4
Receives the digital optical audio signal.
Receives the digital coaxial audio signal.
Receives the video signal from a VCR.
Outputs the video signal to a VCR.
Receives the video signal from a video player (BD/DVD, SAT,TV).
Outputs the video signal to video devices (TV, Projector etc).
Receives the audio signal from a VCR.
Outputs the audio signal to a VCR.
Receives the audio signal from a video player (BD/DVD, SAT,TV, CD).
Connect the subwoofers.
Speaker connection terminals.
5
67
SPEAKER INDICATORS
1
LISTENING MODE INDICATORS
2
TUNING INDICATORS
3
AUDIO INPUT INDICATORS
4
SPEAKER LEVEL INDICATOR
5
RADIO FREQUENCY INDICATORS
6
MESSAGE DISPLAY
7
10
HW-C700-C770S-C770BS-ELS_0309.in10 10HW-C700-C770S-C770BS-ELS_0309.in10 10 2010-03-09 10:11:252010-03-09 10:11:25
Displays the connected speakers.
Displays the current listening mode.
Displays the status of the current radio broadcast.
Displays the audio input signal type of the currently connected external audio source.
Displays the speaker level.
Displays the current radio frequency range.
Informs you of the status of the receiver.
INSERT REMOTE CONTROL BATTERIES
* Batteries (AAA size)
Follow these precautions to avoid leaking or cracking cells:
M
Place batteries in the remote control so they match the polarity : (+) to (+) and (–) to (–).
Assuming typical TV usage, the batteries last for about one year.
Use the correct type of batteries. Batteries that look similar may differ in voltage.
Always replace both batteries at the same time.
Do not expose the batteries to heat or a fl ame.
ENG
● DESCRIPTION
OPERATION RANGE OF THE REMOTE CONTROL
The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also be operated at a
horizontal angle of up to 30° from the remote control sensor.
INPUT SELECT
POWER
TV SOURCE
AMP/TV DIMMER
BD/DVD
RDS DISPLAY
TA
123
PTY- PTY SEARCH
PTY+
456
SLEEPNEO : 6
7809
PROLOGIC AUDIO ASSIGN
DSP
MUTE
TUNING
VOL
/CH
ASC
TUNER MEMORY SUBWOOFER MO/ST
SETUP/MENU
INFO
RETURN
EXIT
TVBD/DVD SAT
CD
iPod
MULTI CH VCR / AUX
11
HW-C700-C770S-C770BS-ELS_0309.in11 11HW-C700-C770S-C770BS-ELS_0309.in11 11 2010-03-09 10:11:252010-03-09 10:11:25
Description
TOUR OF THE REMOTE CONTROL
1
2
3
4
5
6
7
8
9
2
INPUT SELECT
TV SOURCE
BD/DVD
TA
3
PTY+
POWER
AMP/TV DIMMER
RDS DISPLAY
1
PTY- PTY SEARCH
456
SLEEPNEO : 6
7809
PROLOGIC AUDIO ASSIGN
MUTE
VOL
ASC
DSP
TUNING
/CH
16
17
18
19
20
21
22
23
24
25
12
10
11
12
13
14
15
TUNER MEMORY SUBWOOFER MO/ST
SETUP/MENU
RETURN
MULTI CH VCR / AUX
INFO
EXIT
TVBD/DVD SAT
CD
iPod
26
27
28
29
30
HW-C700-C770S-C770BS-ELS_0309.in12 12HW-C700-C770S-C770BS-ELS_0309.in12 12 2010-03-09 10:11:262010-03-09 10:11:26
POWER BUTTON
1
AMP/TV BUTTON
2
NUMBER BUTTONS
3
Turns the receiver on/off.
Used to select the AMP/TV mode.
- If you select the AMP mode, the button will fl ash orange.
- If you select the TV mode, the button will fl ash green.
Used to select a TV channel.
ENG
NEO : 6 BUTTON
4
PROLOGIC BUTTON
5
SKIP BUTTONS
6
STOP/PLAY BUTTON
7
MUTE BUTTON
8
VOLUME CONTROL BUTTONS
9
SUBWOOFER BUTTON
10
TUNER MEMORY BUTTON
11
SETUP/MENU BUTTON
12
UP/DOWN/LEFT/RIGHT BUTTONS
13
RETURN BUTTON
14
FUNCTION SELECTOR BUTTONS
15
INPUT SELECT,
16
TV SOURCE BUTTON
DIMMER BUTTON
17
BD/DVD BUTTON
18
RDS SELECTION BUTTONS
19
Select the desired NEO:6 mode.
Select the desired Dolby Pro Logic audio mode.
Press to skip backwards or forwards on a connected DVD/BD player or iPod.
Press to stop/start playback on a connected DVD/BD player or iPod.
Mutes the sound of a connected device.
Adjusts the volume of the selected device.
Used to select the Subwoofer.
Used to set a preset radio frequency.
Displays the SETUP menu.
Used to navigate the menus.
Used to return to the previous menu from the SETUP menu.
Used to select an input source.
Toggles to fi nd and select an input source.
Press to select a connected TV's video source.
Adjusts the brightness of the display.
Used to select the BD/DVD mode.
- If you select the BD mode, the button will fl ash orange.
- If you select the DVD mode, the button will fl ash green.
Used to select the RDS functions.
● DESCRIPTION
SLEEP BUTTON
20
AUDIO ASSIGN BUTTON
21
DSP BUTTON
22
SEARCH BUTTON
23
PAUSE BUTTON
24
TUNING/CHANNEL BUTTONS
25
ASC BUTTON
26
MO/ST BUTTON
27
INFO BUTTON
28
ENTER BUTTON
29
EXIT BUTTON
30
Used to set the Sleep Timer.
Toggles to select an input mode for the selected source.
Used to select the SFE mode.
Press to search backwards or forwards.
Pauses playback on a connected device.
Used to change the radio broadcasting frequency or TV channel.
Used to set the Auto Sound Calibration function.
Select MONO or STEREO for radio broadcasts.
Display information on the connected device currently being used.
Used to select an item in the SETUP menu.
Exits the SETUP menu.
13
HW-C700-C770S-C770BS-ELS_0309.in13 13HW-C700-C770S-C770BS-ELS_0309.in13 13 2010-03-09 10:11:262010-03-09 10:11:26
Connections
This section involves various methods of connecting the AV receiver to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
SPEAKER POSITIONING
There are two methods for positioning the speakers.
When using Dolby Pro Logic IIz, place the Surround Back Speakers in the FHL, FHR position and connect them to
SURROUND BACK/ FRONT HEIGHT Jack.
* The HW-C700/C700B model does not supply speakers (sold separately).
FHL FHR
6.6~9.8 feet (2~3m)
AV
RECEIVER
SL
SBL
SBR
SR
SL SR
AV
RECEIVER
6.6~9.8 feet (2~3m)
L, R, C, SW, SL, SR, SBL, SBR ( Dolby Pro Logic IIx ) L, R, C, SW, SL, SR, FHL, FHR( Dolby Pro Logic IIz)
Position of AV Receiver
Place the AV Receiver on a dedicated stand or rack.
Subwoofer
The position of the subwoofer is not so critical. Place it anywhere you like.
Subwoofer function (HW-C770S/C779S/C770BS only)
Active subwoofer with integrated 150W amplifi er provides rich
bass sound.
Connect the SW OUT terminal of the amplifi er to the INPUT
•
terminal of the subwoofer speaker.
Press the POWER button on the rear side of the subwoofer to
•
turn the power on.
•
Using the subwoofer’s VOLUME control, you can set the desired
bass level
subwoofer level in the menu).
(See page 36 "Setting the speaker level" to set the
Front Speakers
Place these speakers in front of your listening position, facing inwards (about 45°) toward you.
Place the speakers so that their tweeters will be at the same height as your ears.
Align the front face of the front speakers with the front face of the centre speaker or place them slightly
in front of the centre speaker.
14
HW-C700-C770S-C770BS-ELS_0309.in14 14HW-C700-C770S-C770BS-ELS_0309.in14 14 2010-03-09 10:11:262010-03-09 10:11:26
Centre speaker
It is best to install it at the same height as the front speakers.
You can also install it directly over or under the TV.
ENG
Surround Speakers
Place these speakers behind your listening position.
If there isn't enough room, place these speakers so they face each other.
Place them about 2 to 3 feet (60 to 90cm) above your ears, facing slightly downward.
Unlike the front and centre speakers, the surround speakers are used to handle mainly sound effects
and sound will not come from them all the time.
Surround Back Speakers
If you are using two rear centre speakers, place them behind the listening position.
Place the surround back speaker about 2.3-3.3 feet (70 cm to 1 m).
Front Height Speakers
When using Dolby Pro Logic IIz, place the Surround Back Speakers on the FHL, FHR
position above the front L and front R speakers at least 3.3 feet(1 m) above each one.
- Using the Surround Back Speakers as Front Height Speakers -
1.
Fasten 2 screws(not supplied) for each speaker on the wall
above the front L and R speakers.
2.
Install the Surround Back Speakers (L, R) by fi tting the
holes on the back the Surround Back Speakers to the
screws on the wall.
When you attach the speakers to the wall, make sure to fasten them tightly so they do not fall off.
M
FHL FHR
SBL SBR
When you
(Using Dolby Pro Logic IIz)
● CONNECTIONS
Speaker Confi guration
For the best surround-sound experience, you should connect seven speakers and a powered subwoofer.
The following table shows which channels you should use based on the number of speakers you have.
2 speakers 3 speakers 4 speakers 5 speakers 6 speakers
SBL SBL
No matter how many speakers you use, a powered subwoofer is recommended for powerful and solid bass.
M
If you place a speaker near your TV set, screen colour may be distorted because of the magnetic fi eld
generated by the speaker. If this occurs, place the speaker away from your TV set.
7 speakers
(DPL IIx)
SBR
7 speakers
(DPL IIz)
FHL
FHR
15
HW-C700-C770S-C770BS-ELS_0309.in15 15HW-C700-C770S-C770BS-ELS_0309.in15 15 2010-03-09 10:11:272010-03-09 10:11:27
Connections
CONNECTING THE SPEAKERS
FRONT (R)
PS-FC770S
ACTIVE SUBWOOFER
(BUILT-IN POWER AMPLIFIER)
PS-AW730
SURROUND (R)
SURROUND BACK (R)
PS-RC770S
PS-BC770S
SURROUND BACK (L)
PS-BC770S
CENTRE
PS-CC770S
SURROUND (L)
FRONT (L)
PS-RC770S
PS-FC770S
Model HW-C700/C700B
AV Receiver HW-C700/C700B
Model HW-C770S/C779S/C770BS
AV Receiver
FRONT SPEAKER PS-FC770S
CENTRE
SPEAKER PS-CC770S
SURROUND SPEAKER PS-RC770S
SURROUND BACK SPEAKER PS-BC770S
ACTIVE SUBWOOFER PS-AW730
HW-C770S/C779S/
C770BS
One Active Subwoofer is provided, if you would like to use another, purchase it from the retailer where you bought
M
the player and connect it to the other SUBWOOFER OUT Jack.
When using Dolby Pro Logic IIz, connect the Surround Back Speakers (FHL, FHR) to SURROUND BACK/FRONT
HEIGHT Jack.
Connecting Speaker Wire
Loosen the knob by turning counterclockwise.
1.
Insert the bare part of the wire into the hole in the side of each
2.
terminal.
Tighten the knob by turning clockwise to secure the wire.
3.
Keep the subwoofer speaker out of reach of children to prevent them from inserting their hands or objects
M
into the duct (hole).
Never touch speaker terminals while the power is on. Doing so could result in electric shock.
Make sure the polarities (+ and -) are correct.
Connecting the Speakers
Press down the terminal tab on the back of the speaker.
1.
Insert the black wire into the black terminal (–) and the red wire into
2.
the red (+) terminal, and then release the tab.
Connect the connecting plugs to the back of the AV Receiver.
3.
Make sure the colours of the speaker terminals on the back of the
•
AV receiver match the colours of the connecting plugs.
Black
Red
16
HW-C700-C770S-C770BS-ELS_0309.in16 16HW-C700-C770S-C770BS-ELS_0309.in16 16 2010-03-09 10:28:322010-03-09 10:28:32
CONNECTING EXTERNAL DEVICES/YOUR TV VIA HDMI
OPTICAL
OUT
HDMI is a digital standard interface for connection to such devices as a TV, projector, DVD player, Blu-ray player, set-top
box and more.
HDMI removes any loss of signal from analogue conversion, enabling you to enjoy video and audio sound quality as it
was originally created in the digital source.
By connecting through the HDMI(High-Defi nition Multimedia Interface) interface, you can play back digital video and audio.
ENG
● CONNECTIONS
DVD or
Blu-ray Player
•
Connect it if you want
to use Anynet+.
SAT
(Cable/Satellite/Set-top box)
Game console
Camcorder
or
HDTV Tuner
(HDTV Terrestrial Receiver)
High-bandwidth Digital Content Protection System (HDCP) support
To play digital contents through the HDMI connection, both the connected external device and TV must
support High-bandwidth Digital Content Protection System (HDCP). This product supports HDCP.
Compatibility with a TV Supporting HDMI
A TV with an HDMI jack. Video/Audio
A TV with a DVI-D jack (TV supporting HDCP) Video
A TV with a DVI-D jack (TV not supporting HDCP) -
Audio from SACD discs will not be heard with this connection. To play a DVD disc whose copyright is protected
M
by CPPM, use a player supporting CPPM.
The quality of the audio output through the HDMI jack (sampling frequency and bit rate) may be limited by the
performance of the connected device.
Since HDMI connection supports both video and audio, you don’t have to connect an additional audio cable.
17
HW-C700-C770S-C770BS-ELS_0309.in17 17HW-C700-C770S-C770BS-ELS_0309.in17 17 2010-03-09 10:11:332010-03-09 10:11:33
Connections
HDMI FUNCTION
Using Anynet+(HDMI-CEC)
Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's
remote control. Anynet + can be used by connecting this AV Receiver to a SAMSUNG TV using an
HDMI Cable. This is only available with SAMSUNG TVs and SAMSUNG AV Products that support
Anynet+.
1.
Connect the AV receiver to a Samsung TV with an HDMI cable. (See page 17)
2.
Set the Anynet+ function on your TV.
(See the TV instructions manual for more information.)
•
You can operate the volume on the AV receiver by using Volume buttons on the TV remote
control.
To turn on Anynet+
1.
Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.
2.
Press the ENTER button to select SETUP ENTER.
3.
Press the ▲▼ buttons to select HDMI SETUP, and then press the ENTER or ► button.
4.
Press the ▲▼ buttons to select HDMI ANYNET+, and then press the ENTER or ► button.
5.
Press the ▲▼ buttons to set ANYNET+ to ON.
- To exit setup mode-
•
Press the SETUP/MENU button.
SETUP OFF appears on the display and Setup Mode is exited.
If you use an HDMI cable to connect a Samsung TV to your AV Receiver, you can operate the AV receiver using
M
the TV’s remote control. This function is available only in connection with Samsung TV and DVD player
supporting Anynet +(HDMI-CEC).
Please check your TV for the n logo. If your TV has an n logo, then it supports the Anynet+
function.
When you are making Anynet+ connection, do not connect more than two AV receivers (Anynet+ installed).
Otherwise, it can cause a malfunction.
18
HW-C700-C770S-C770BS-ELS_0309.in18 18HW-C700-C770S-C770BS-ELS_0309.in18 18 2010-03-09 10:11:372010-03-09 10:11:37
CONNECTING TO YOUR TV
or or
ENG
● CONNECTIONS
COMPONENT
IN
VIDEO
IN
OPTICAL
OUT
AUDIO
OUT
Video Connection
If your television is equipped with Component Video inputs, connect a Component video cable(not
supplied) from the Component Video Output (PR, PB and Y) jacks on the back of your AV Receiver to the
Component Video Input jacks on your TV.
OR
Connect the Video cable from the VIDEO OUT (MONITOR) jack on the back of your AV Receiver to the
Video Input jack on your TV.
Audio Connection
Connect the Digital Input (OPTICAL 3) on your AV Receiver to the Digital Output of the TV.
OR
Connect AUDIO IN (TV) on your AV Receiver to the Audio Out of the TV.
19
HW-C700-C770S-C770BS-ELS_0309.in19 19HW-C700-C770S-C770BS-ELS_0309.in19 19 2010-03-09 10:11:372010-03-09 10:11:37
Loading...