Samsung HW-C700B-XAA User Manual

Download

HW-C700 HW-C700B HW-C770S HW-C770BS

AV Receiver System

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register your product at

www.samsung.com/register

HW-C700-C770S-C770BS-XAA_0609.in1 1HW-C700-C770S-C770BS-XAA_0609.in1 1 2010-06-09  5:06:292010-06-09  5:06:29

Safety information

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates “dangerous voltage”

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

•

To reduce the risk of ﬁ re or electric shock, do not expose this appliance to rain or moisture. To prevent injury, this apparatus must be securely attached to the ﬂ oor/wall in accordance with the installation instructions.

•

CAUTION

Apparatus shall not be exposed to dripping or splashing and no objects ﬁ lled with liquids, such as vases, shall be placed on the

•

apparatus. The Mains plug is used as a disconnect device and shall stay readily operable at any time.

•

This product satisﬁ es FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances, such as radios and televisions, use shielded cables and connectors for connections.

FCC NOTE (for U.S.A):

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

inside the product that presents a risk of electric shock or personal injury.

This symbol indicates important instructions accompanying the product.

Caution :

FCC regulations state that any unauthorized changes or modiﬁ cations to this equipment may void the user's authority to operate it.

HW-C700-C770S-C770BS-XAA_0609.in2 2HW-C700-C770S-C770BS-XAA_0609.in2 2 2010-06-09  5:06:332010-06-09  5:06:33

IMPORTANT SAFETY INSTRUCTIONS

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE: FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth an uncontrolled environment. This equipment should be installed and operated with minimum distance 7.9 inches between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Canadian Department of Communications Radio Interference Regulations

This digital apparatus (Wireless Internet Radio) does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.

Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference.

1) Read these instructions.

2) Keep these Instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

8) ampliﬁ ers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁ t into your outlet, consult an electrician for replacement of the obsolete outlet.

10)

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachment/accessories speciﬁ ed by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table speciﬁ ed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

ENG

HW-C700-C770S-C770BS-XAA_0609.in3 3HW-C700-C770S-C770BS-XAA_0609.in3 3 2010-06-09  5:06:332010-06-09  5:06:33

Safety information

PRECAUTIONS

2.7 inches

3.9 inches

Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure the ventilation slots are not covered. Do not stack anything on top of the amplifier. In order to disconnect the player completely from the power supply, remove the AC plug from the wall outlet, especially when left unused for a long period of time.

During thunderstorms, disconnect the AC plug from the wall outlet. Voltage peaks due to lightning could damage the unit.

Phones

Protect the player from moisture(i.e. vases), and excess heat(e.g.fireplace) or equipment creating strong magnetic or electric fields (i.e.speakers...). Disconnect the power cable from the AC supply if the player malfunctions. Your player is not intended for industrial use.

Use of this product is for personal use only. Condensation may occur if your player or disc have been

stored in cold temperatures. If transporting the player during the winter, wait

approximately 2 hours until the unit has reached room temperature before using.

Do not expose the unit to direct sunlight or other heat sources.

This could lead to overheating and malfunction of the unit.

The batteries used with this product contain

chemicals that are harmful to the environment.

Do not dispose of batteries in the general household

trash.

HW-C700-C770S-C770BS-XAA_0609.in4 4HW-C700-C770S-C770BS-XAA_0609.in4 4 2010-06-09  5:06:342010-06-09  5:06:34

Features

ENG

Digital AV Receiver

This product is a pure digital AV receiver that performs digital signal processing to minimize signal distortion and loss.

Dolby Pro Logic llx

Dolby Pro Logic IIx is a new technology that provides discrete 7.1 channels out of 2 channel or multi channel sources.It also provides Music,Movie and Game modes. Dolby Pro Logic IIx is an improved surround system that is optimized to a 7.1 CH multimedia system, enabling you to maximize your entertainment experience.

Dolby Pro Logic llz

Dolby Pro Logic IIz adds front height channels to surround sound, creating a 7.1 playback system for video games, home music, and movies; bringing enhanced spatial effects and enveloping sound.

DTS 96/24

DTS 96/24 encodes standard 16 bit/44.1 kHz sound to 24 bit/96kHz and applies it to a 5.1 CH sound track.

DOLBY DIGITAL EX

Adds a surround back channel for more spacious sound compared to regular 5.1 channel Dolby Digital.

DTS (Digital Theater Systems)

DTS provides a discrete 5.1 CH digital audio signal for both music and movie contents and uses less compression than Dolby Digital for richer sound.

Dolby Digital Plus

Dolby Digital Plus is the next-generation audio technology for all high-deﬁ nition programming and media.

Dolby True-HD

Dolby True-HD is Dolby’s next-generation lossless technology developed for high-deﬁ nition disc-based media.

DTS-HD (Master Audio, High Resolution) (Digital Theater Systems - High Deﬁ nition)

DTS-HD Audio provides the highest quality multi-channel sound possible. It delivers sound quality that matches the clear and vivid images of high-deﬁ nition video.

DTS

Provides a full range of 6 channels by converting a digital PCM or analog stereo signal using DTS digital matrix decoding.

iPod

You can enjoy music ﬁ les by connecting your iPod/iPhone to the AV Receiver with the supplied iPod dock.

SFE (Sound Field Effect) Using 32bit Audio Digital Signal Processing

Provides more realistic surround sound with normal stereo audio sources.

Anynet+ (HDMI-CEC) Function

Anynet+ is a function that can be used to operate this AV Receiver with a Samsung TV remote control, by connecting the receiver to a SAMSUNG TV using an HDMI Cable. (This function is available only in connection with Samsung TV and DVD player supporting Anynet+(HDMI-CEC).)

DTS-ES (Extended Surround)

The DTS-ES (Extended Surround) system is a new multi digital signal format that was developed by Digital Theater Systems Inc. Supporting full compatibility with the conventional DTS digital surround sound format, the DTS-ES (Extended Surround) system improves the surround signal for a 360degree surround effect. DTS-ES adds an additional rear center surround channel for

6.1 channel sound.

ACCESSORIES

INPUT SELECT

POWER

TV SOURCE

AMP/TV DIMMER

BD/DVD

123

456

SLEEPNEO : 6

7809

PROLOGIC AUDIO ASSIGN

DSP

MUTE

TUNING

VOL

/CH

ASC

TUNER MEMORY SUBWOOFER MO/ST

SETUP/MENU

INFO

RETURN

EXIT

TVBD/DVD SAT

iPod

MULTI CH VCR / AUX

Remote Control

(AH59-02307A)/

Batteries (AAA size)

(4301-000116)

HW-C700-C770S-C770BS-XAA_0609.in5 5HW-C700-C770S-C770BS-XAA_0609.in5 5 2010-06-09  5:06:372010-06-09  5:06:37

FM antenna

(AH42-00017A)

User’s manual

(AH68-02260R)

iPod Dock

(AH96-00051A)

ASC microphone

( AH30-00099A )

Contents

SAFETY INFORMATION

FEATURES

DESCRIPTION

CONNECTIONS

2 Safety Warnings 3 Important Safety Instructions 4 Precautions

5 Accessories

8 Front Panel 10 Rear Panel 12 Display 13 Insert Remote Control Batteries 13 Operation Range of the Remote Control 14 Tour of the Remote Control

16 Speaker Positioning 18 Connecting the Speakers 19 Connecting External Devices/Your TV via

HDMI 20 HDMI Function 21 Connecting to your TV 22 Connecting a DVD or BD(Blu-ray) Player 23 Connecting a Cable, Satellite or Set-top Box 24 Connecting a VCR 25 Connecting a CD Player 26 Connecting 7.1 Channel Devices 27 Connecting an iPod 29 Connecting the FM Antenna 29 Connecting Aux Components

BASIC FUNCTIONS OF YOUR AV

RECEIVER

30 Before Using the AV Receiver 30 Audio Setup 31 Selecting Digital/Analog Input

HW-C700-C770S-C770BS-XAA_0609.in6 6HW-C700-C770S-C770BS-XAA_0609.in6 6 2010-06-09  5:06:392010-06-09  5:06:39

ENG

SETUP

OPERATION

32 Setup Menu Tree 36 Setting the Speaker Size 37 Setting the Speaker Listening Distance 38 Setting the Speaker Level 39 Setting the Test Tone 40 Setting Dolby Pro Logic Mode 40 Setting Dolby Pro Logic IIx 41 Setting Dolby Pro Logic IIz 41 Setting Tone Control 42 Setting NEO:6 Mode 43 Setting EX/ES Mode 44 AV SYNC 44 MP3 Enhancer 44 Smart Volume 45 ASC (Auto Sound Calibration) Setup 46 DRC Setup 46 HDMI Setup 46 Variable Set

47 Using the Surround Modes 48 Using the Subwoofer Selection Button 49 Listening to the Radio 50 Using an iPod 52 Convenient Functions 53 Software Upgrade

● CONTENTS

MISCELLANEOUS

TROUBLESHOOTING

APPENDIX

54 Operating Your TV With the Remote Control 56 Operating your DVD or BD player with the

remote control

57 Troubleshooting

59 Speciﬁ cations

HW-C700-C770S-C770BS-XAA_0609.in7 7HW-C700-C770S-C770BS-XAA_0609.in7 7 2010-06-09  5:06:392010-06-09  5:06:39

Description

FRONT PANEL

1 2 3

10 11 1412 13

5 6 7

15 16 17

84 9

18 19 20

HEADPHONE JACK

AUX IN JACKS

ASC MIC JACK

DISPLAY

S.DIRECT/STEREO BUTTON

MULTI CH BUTTON

AV SYNC BUTTON

VOLUME CONTROL

POWER

HW-C700-C770S-C770BS-XAA_0609.in8 8HW-C700-C770S-C770BS-XAA_0609.in8 8 2010-06-09  5:06:392010-06-09  5:06:39

Used to connect a set of headphones.

Auxiliary AV input terminals used to connect a camcorder, portable DVD player or gaming device.

Used to connect the ASC MIC for setting up ASC (Auto Sound Calibration).

Displays the speaker/audio input status, listening mode, etc.

Used to select the S.DIRECT or STEREO mode.

Used to select a connected 7.1 multi channel player.

Used to select the Audio Delay Mode.

Adjusts the volume level.

Turns the receiver on/off.

INPUT SELECT BUTTON

ENG

Used to select a source. (FM  BD/DVD  SAT  TV  VCR CD  AUX  7.1 MULTI CH  IPOD AUDIO  IPOD VIDEO).

AUDIO ASSIGN BUTTON

SOUND EFFECT BUTTON

SETUP BUTTON

UP(,), DOWN(.), LEFT(<),

RIGHT(>) BUTTONS

ENTER BUTTON

TONE CONTROL

ASC BUTTON

TUNING MODE BUTTON

SELECT BUTTON

MEMORY BUTTON

BUTTON

Toggles to select an input mode for the selected source.

Toggles to select a surround sound mode.

Displays the SETUP menu.

Used to move the cursor up, down, left or right.

Also used to select detailed options in the SOUND EFFECT mode and to change the tone level.

Used to select an item in the SETUP menu.

Used to set the bass, treble level and tone to on/off.

Used to select the ASC (Auto Sound Calibration) mode.

Used to select the Manual or Preset mode for FM radio.

Used to change the radio frequency.

Used to set a preset radio frequency.

● DESCRIPTION

HW-C700-C770S-C770BS-XAA_0609.in9 9HW-C700-C770S-C770BS-XAA_0609.in9 9 2010-06-09  5:06:402010-06-09  5:06:40

Description

REAR PANEL

1 2 3 4 5

8 9 10 18 196 7

11 12 13 14

15 16 17

HW-C700-C770S-C770BS-XAA_0609.in10 10HW-C700-C770S-C770BS-XAA_0609.in10 10 2010-06-09  5:06:402010-06-09  5:06:40

ENG

FM ANTENNA JACK

MULTI CH IN JACKS

HDMI IN JACKS

HDMI OUT JACK

USB PORT

COMPONENT VIDEO IN JACKS

COMPONENT VIDEO OUT JACKS

iPod JACK

OPTICAL IN JACKS (DIGITAL AUDIO IN)

COAXIAL IN JACK (DIGITAL AUDIO IN)

VCR VIDEO IN JACK

VCR VIDEO OUT JACK

VIDEO IN JACKS

VIDEO OUT JACK

Connect the FM Antenna here.

Receives the analog audio signal from an external player with a multi-channel port.

Receives digital video and audio signals simultaneously using an HDMI cable.

Outputs digital video and audio signals simultaneously using an HDMI cable.

Can be only used for ﬁ rmware upgrades.

Receives the component video signal.

Outputs the component video signal.

Receives the audio/video signal from an iPod.

Receives the digital optical audio signal.

Receives the digital coaxial audio signal.

Receives the video signal from a VCR.

Outputs the video signal to a VCR.

Receives the video signal from a video player (BD/DVD, SAT,TV).

Outputs the video signal to video devices (TV, Projector etc).

● DESCRIPTION

VCR AUDIO IN JACKS

VCR AUDIO OUT JACKS

AUDIO IN JACKS

SUBWOOFER AUDIO OUT JACKS

SPEAKER OUT TERMINALS

Receives the audio signal from a VCR.

Outputs the audio signal to a VCR.

Receives the audio signal from a video player (BD/DVD, SAT,TV, CD).

Connect the subwoofers.

Speaker connection terminals.

HW-C700-C770S-C770BS-XAA_0609.in11 11HW-C700-C770S-C770BS-XAA_0609.in11 11 2010-06-09  5:06:412010-06-09  5:06:41

Description

DISPLAY

1 2 3 4

SPEAKER INDICATORS

LISTENING MODE INDICATORS

TUNING INDICATORS

AUDIO INPUT INDICATORS

SPEAKER LEVEL INDICATOR

RADIO FREQUENCY INDICATORS

MESSAGE DISPLAY

Displays the connected speakers.

Displays the current listening mode.

Displays the status of the current radio broadcast.

Displays the audio input signal type of the currently connected external audio source.

Displays the speaker level.

Displays the current radio frequency range.

Informs you of the status of the receiver.

HW-C700-C770S-C770BS-XAA_0609.in12 12HW-C700-C770S-C770BS-XAA_0609.in12 12 2010-06-09  5:06:412010-06-09  5:06:41

INSERT REMOTE CONTROL BATTERIES

* Batteries (AAA size)

Follow these precautions to avoid leaking or cracking cells:

Place batteries in the remote control so they match the polarity : (+) to (+) and (–) to (–).



Assuming typical TV usage, the batteries last for about one year.



Use the correct type of batteries. Batteries that look similar may differ in voltage.



Always replace both batteries at the same time.



Do not expose the batteries to heat or a ﬂ ame.



ENG

● DESCRIPTION

OPERATION RANGE OF THE REMOTE CONTROL

The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also be operated at a horizontal angle of up to 30° from the remote control sensor.

INPUT SELECT

POWER

TV SOURCE

AMP/TV DIMMER

BD/DVD

123

456

SLEEPNEO : 6

7809

PROLOGIC AUDIO ASSIGN

DSP

MUTE

TUNING

VOL

/CH

ASC

TUNER MEMORY SUBWOOFER MO/ST

SETUP/MENU

INFO

RETURN

EXIT

TVBD/DVD SAT

iPod

MULTI CH VCR / AUX

HW-C700-C770S-C770BS-XAA_0609.in13 13HW-C700-C770S-C770BS-XAA_0609.in13 13 2010-06-09  5:06:412010-06-09  5:06:41

Description

TOUR OF THE REMOTE CONTROL

INPUT SELECT

TV SOURCE

BD/DVD

POWER

AMP/TV DIMMER

456

SLEEPNEO : 6

7809

PROLOGIC AUDIO ASSIGN

MUTE

VOL

ASC

DSP

TUNING

/CH

16 17

10 11

TUNER MEMORY SUBWOOFER MO/ST

SETUP/MENU

RETURN

MULTI CH VCR / AUX

INFO

EXIT

TVBD/DVD SAT

iPod

25 26

27 28

HW-C700-C770S-C770BS-XAA_0609.in14 14HW-C700-C770S-C770BS-XAA_0609.in14 14 2010-06-09  5:06:422010-06-09  5:06:42

POWER BUTTON

AMP/TV BUTTON

NUMBER BUTTONS

Turns the receiver on/off.

Used to select the AMP/TV mode.

- If you select the AMP mode, the button will ﬂ ash orange.

- If you select the TV mode, the button will ﬂ ash green.

Used to select a TV channel.

ENG

NEO : 6 BUTTON

PROLOGIC BUTTON

SKIP BUTTONS

STOP/PLAY BUTTON

MUTE BUTTON

VOLUME CONTROL BUTTONS

SUBWOOFER BUTTON

TUNER MEMORY BUTTON

SETUP/MENU BUTTON

UP/DOWN/LEFT/RIGHT BUTTONS

RETURN BUTTON

FUNCTION SELECTOR BUTTONS

INPUT SELECT,

TV SOURCE BUTTON

DIMMER BUTTON

BD/DVD BUTTON

SLEEP BUTTON

Select the desired NEO:6 mode.

Select the desired Dolby Pro Logic audio mode.

Press to skip backwards or forwards on a connected DVD/BD player or iPod.

Press to stop/start playback on a connected DVD/BD player or iPod.

Mutes the sound of a connected device.

Adjusts the volume of the selected device.

Used to select the Subwoofer.

Used to set a preset radio frequency.

Displays the SETUP menu.

Used to navigate the menus.

Used to return to the previous menu from the SETUP menu.

Used to select an input source.

Toggles to ﬁ nd and select an input source.

Press to select a connected TV's video source.

Adjusts the brightness of the display.

Used to select the BD/DVD mode.

- If you select the BD mode, the button will ﬂ ash orange.

- If you select the DVD mode, the button will ﬂ ash green.

Used to set the Sleep Timer.

● DESCRIPTION

AUDIO ASSIGN BUTTON

DSP BUTTON

SEARCH BUTTON

PAUSE BUTTON

TUNING/CHANNEL BUTTONS

ASC BUTTON

MO/ST BUTTON

INFO BUTTON

ENTER BUTTON

EXIT BUTTON

Toggles to select an input mode for the selected source.

Used to select the SFE mode.

Press to search backwards or forwards.

Pauses playback on a connected device.

Used to change the radio broadcasting frequency or TV channel.

Used to set the Auto Sound Calibration function.

Select MONO or STEREO for radio broadcasts.

Display information on the connected device currently being used.

Used to select an item in the SETUP menu.

Exits the SETUP menu.

HW-C700-C770S-C770BS-XAA_0609.in15 15HW-C700-C770S-C770BS-XAA_0609.in15 15 2010-06-09  5:06:422010-06-09  5:06:42

Connections

This section involves various methods of connecting the AV receiver to other external components. Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

SPEAKER POSITIONING

There are two methods for positioning the speakers. When using Dolby Pro Logic IIz, place the Surround Back Speakers in the FHL, FHR position and connect them to SURROUND BACK/ FRONT HEIGHT Jack.

* Speakers are provided with model HW-C770S/HW-C770BS only. Model HW-C700/C700B does not come

with speakers.

FHL FHR

6.6~9.8 feet (2~3m)

RECEIVER

SBL

SBR

RECEIVER

6.6~9.8 feet (2~3m)

L, R, C, SW, SL, SR, SBL, SBR ( Dolby Pro Logic IIx ) L, R, C, SW, SL, SR, FHL, FHR( Dolby Pro Logic IIz)

Position of AV Receiver

Place the AV Receiver on a dedicated stand or rack.

Subwoofer

The position of the subwoofer is not so critical. Place it anywhere you like.

Subwoofer function (HW-C770S/C770BS only)

Active subwoofer with integrated 150W ampliﬁ er provides rich bass sound.

Connect the SW OUT terminal of the ampliﬁ er to the INPUT

•

terminal of the subwoofer speaker. Press the POWER button on the rear side of the subwoofer to

•

turn the power on. Using the subwoofer’s VOLUME control, you can set the desired

•

bass level subwoofer level in the menu).

(See page 38 "Setting the speaker level" to set the

Front Speakers

Place these speakers in front of your listening position, facing inwards (about 45°) toward you.

Place the speakers so that their tweeters will be at the same height as your ears.

Align the front face of the front speakers with the front face of the center speaker or place them slightly

HW-C700-C770S-C770BS-XAA_0609.in16 16HW-C700-C770S-C770BS-XAA_0609.in16 16 2010-06-09  5:06:422010-06-09  5:06:42

in front of the center speaker.

Center speaker

It is best to install it at the same height as the front speakers.

You can also install it directly over or under the TV.

ENG

Surround Speakers

Place these speakers behind your listening position.

If there isn't enough room, place these speakers so they face each other.

Place them about 2 to 3 feet (60 to 90cm) above your ears, facing slightly downward.

Unlike the front and center speakers, the surround speakers are used to handle mainly sound effects and sound will not come from them all the time.

Surround Back Speakers

If you are using two rear center speakers, place them behind the listening position.

Place the surround back speaker about 2.3-3.3 feet (70 cm to 1 m).

Front Height Speakers

When using Dolby Pro Logic IIz, place the Surround Back Speakers on the FHL, FHR position above the front L and front R speakers at least 3.3 feet(1 m) above each one.

- Using the Surround Back Speakers as Front Height Speakers -

Fasten 2 screws(not supplied) for each speaker on the wall

above the front L and R speakers.

Install the Surround Back Speakers (L, R) by ﬁ tting the

holes on the back the Surround Back Speakers to the screws on the wall.

When you attach the speakers to the wall, make sure to fasten them tightly so they do not fall off.



FHL FHR

SBL SBR

When you

(Using Dolby Pro Logic IIz)

● CONNECTIONS

Speaker Conﬁ guration

For the best surround-sound experience, you should connect seven speakers and a powered subwoofer.

The following table shows which channels you should use based on the number of speakers you have.

2 speakers 3 speakers 4 speakers 5 speakers 6 speakers

SBL SBL

No matter how many speakers you use, a powered subwoofer is recommended for powerful and solid bass.



If you place a speaker near your TV set, screen color may be distorted because of the magnetic ﬁ eld generated



by the speaker. If this occurs, place the speaker away from your TV set.

7 speakers

(DPL IIx)

SBR

7 speakers

(DPL IIz)

FHL

FHR

HW-C700-C770S-C770BS-XAA_0609.in17 17HW-C700-C770S-C770BS-XAA_0609.in17 17 2010-06-09  5:06:432010-06-09  5:06:43

Connections

CONNECTING THE SPEAKERS

FRONT (R)

PS-FC770S

ACTIVE SUBWOOFER

(BUILT-IN POWER AMPLIFIER)

PS-AW730

SURROUND (R)

SURROUND BACK (R)

PS-RC770S

PS-BC770S

SURROUND BACK (L)

CENTER

PS-CC770S

SURROUND (L)

PS-RC770S

FRONT (L)

PS-FC770S

PS-BC770S

Model HW-C700/C700B AV Receiver HW-C700/C700B

Model HW-C770S/C770BS AV Receiver HW-C770S/C770BS FRONT SPEAKER PS-FC770S CENTER SPEAKER PS-CC770S SURROUND SPEAKER PS-RC770S SURROUND BACK SPEAKER PS-BC770S ACTIVE SUBWOOFER PS-AW730

Speakers are provided with model HW-C770S/HW-C770BS only. Model HW-C700/C700B does not come with speakers.



One Active Subwoofer is provided, if you would like to use another, purchase it from the retailer where you bought the player and connect it to the other SUBWOOFER OUT Jack.



When using Dolby Pro Logic IIz, connect the Surround Back Speakers (FHL, FHR) to SURROUND BACK/FRONT HEIGHT Jack.

Connecting Speaker Wire

Loosen the knob by turning counterclockwise.

Insert the bare part of the wire into the hole in the side of each

terminal.

Tighten the knob by turning clockwise to secure the wire.

Keep the subwoofer speaker out of reach of children to prevent them from inserting their hands or objects



into the duct (hole).



Never touch speaker terminals while the power is on. Doing so could result in electric shock.



Make sure the polarities (+ and -) are correct.

Connecting the Speakers

Press down the terminal tab on the back of the speaker.

Insert the black wire into the black terminal (–) and the red wire into

the red (+) terminal, and then release the tab.

Connect the connecting plugs to the back of the AV Receiver.

Make sure the colors of the speaker terminals on the back of the

•

AV receiver match the colors of the connecting plugs.

Black

Red

HW-C700-C770S-C770BS-XAA_0609.in18 18HW-C700-C770S-C770BS-XAA_0609.in18 18 2010-06-09  5:06:462010-06-09  5:06:46

CONNECTING EXTERNAL DEVICES/YOUR TV VIA HDMI

OPTICAL OUT

HDMI is a digital standard interface for connection to such devices as a TV, projector, DVD player, Blu-ray player, set-top box and more.

HDMI removes any loss of signal from analog conversion, enabling you to enjoy video and audio sound quality as it was originally created in the digital source.

By connecting through the HDMI(High-Deﬁ nition Multimedia Interface) interface, you can play back digital video and audio.

ENG

● CONNECTIONS

DVD or

Blu-ray Player

•

Connect it if you want to use Anynet+.

SAT

(Cable/Satellite/Set-top box)

Game console

Camcorder or HDTV Tuner

(HDTV Terrestrial Receiver)

High-bandwidth Digital Content Protection System (HDCP) support

To play digital contents through the HDMI connection, both the connected external device and TV must support High-bandwidth Digital Content Protection System (HDCP). This product supports HDCP.

Compatibility with a TV Supporting HDMI

A TV with an HDMI jack. Video/Audio

A TV with a DVI-D jack (TV supporting HDCP) Video

A TV with a DVI-D jack (TV not supporting HDCP) -

Audio from SACD discs will not be heard with this connection. To play a DVD disc whose copyright is protected



by CPPM, use a player supporting CPPM. The quality of the audio output through the HDMI jack (sampling frequency and bit rate) may be limited by the



performance of the connected device. Since HDMI connection supports both video and audio, you don’t have to connect an additional audio cable.



HW-C700-C770S-C770BS-XAA_0609.in19 19HW-C700-C770S-C770BS-XAA_0609.in19 19 2010-06-09  5:06:512010-06-09  5:06:51

Connections

HDMI FUNCTION

Using Anynet+(HDMI-CEC)

Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's remote control. Anynet + can be used by connecting this AV Receiver to a SAMSUNG TV using an HDMI Cable. This is only available with SAMSUNG TVs and SAMSUNG AV Products that support Anynet+.

Connect the AV receiver to a Samsung TV with an HDMI cable. (See page 19)

Set the Anynet+ function on your TV. (See the TV instructions manual for more information.)

•

You can operate the volume on the AV receiver by using Volume buttons on the TV remote

control.

To turn on Anynet+

Press the SETUP/MENU button.

•

Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the ▲▼ buttons to select HDMI SETUP, and then press the ENTER or ► button.

Press the ▲▼ buttons to select HDMI ANYNET+, and then press the ENTER or ► button.

Press the ▲▼ buttons to set ANYNET+ to ON.

- To exit setup mode-

•

Press the SETUP/MENU button. SETUP OFF appears on the display and Setup Mode is exited.

If you use an HDMI cable to connect a Samsung TV to your AV Receiver, you can operate the AV receiver using



the TV’s remote control. This function is available only in connection with Samsung TV and DVD player supporting Anynet +(HDMI-CEC).

Please check your TV for the n logo. If your TV has an n logo, then it supports the Anynet+



function.

When you are making Anynet+ connection, do not connect more than two AV receivers (Anynet+ installed).



Otherwise, it can cause a malfunction.

HW-C700-C770S-C770BS-XAA_0609.in20 20HW-C700-C770S-C770BS-XAA_0609.in20 20 2010-06-09  5:06:552010-06-09  5:06:55

CONNECTING TO YOUR TV

or or

ENG

● CONNECTIONS

COMPONENT IN

VIDEO IN

OPTICAL OUT

AUDIO OUT

Video Connection

If your television is equipped with Component Video inputs, connect a Component video cable(not supplied) from the Component Video Output (PR, PB and Y) jacks on the back of your AV Receiver to the Component Video Input jacks on your TV.

Connect the Video cable from the VIDEO OUT (MONITOR) jack on the back of your AV Receiver to the Video Input jack on your TV.

Audio Connection

Connect the Digital Input (OPTICAL 3) on your AV Receiver to the Digital Output of the TV.

Connect AUDIO IN (TV) on your AV Receiver to the Audio Out of the TV.

HW-C700-C770S-C770BS-XAA_0609.in21 21HW-C700-C770S-C770BS-XAA_0609.in21 21 2010-06-09  5:06:552010-06-09  5:06:55

Connections

CONNECTING A DVD OR BD(Blu-ray) PLAYER

COMPONENT IN

VIDEO IN

COMPONENT OUT

OPTICAL OUT

AUDIO OUT

VIDEO OUT

DVD or BD Player

Video Connection

Connect a Component video cable(not supplied) from the COMPONENT IN (BD/DVD) (PR, PB and Y) jacks on the back of your AV Receiver to the Component Video Output jacks on your DVD/BD player.

Connect a Video cable from the VIDEO IN (BD/DVD) jack on the back of your AV Receiver to the Video Output jack on your DVD/BD player.

Audio Connection

Connect the Digital Input (OPTICAL 1) on your AV Receiver to the Digital Output of the DVD/BD player.

Connect AUDIO IN (BD/DVD) on your AV Receiver to the Audio Out of the DVD/BD player.

HW-C700-C770S-C770BS-XAA_0609.in22 22HW-C700-C770S-C770BS-XAA_0609.in22 22 2010-06-09  5:06:592010-06-09  5:06:59

CONNECTING A CABLE, SATELLITE OR SET-TOP BOX

ENG

COMPONENT IN

VIDEO IN

● CONNECTIONS

SAT

(Cable/Satellite/Set-top box)

COMPONENT OUT

OPTICAL OUT

AUDIO OUT

VIDEO OUT

Video Connection

Connect a Component video cable(not supplied) from the COMPONENT IN (SAT) (PR, PB and Y) jacks on the back of your AV Receiver to the Component Video Output jacks on your SAT.

Connect a Video cable from the VIDEO IN (SAT) jack on the back of your AV Receiver to the Video Output jack on your SAT.

Audio Connection

Connect the Digital Input (OPTICAL 2) on your AV Receiver to the Digital Output of the SAT.

Connect AUDIO IN (SAT) on your AV Receiver to the Audio Out of the SAT.

Disconnect the power plug from the outlet if you will not use this unit for a long period of time.



If the cable/set-top box has only one audio output jack, connect it to either the right or left audio input jack of



the main unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.

HW-C700-C770S-C770BS-XAA_0609.in23 23HW-C700-C770S-C770BS-XAA_0609.in23 23 2010-06-09  5:07:022010-06-09  5:07:02

Connections

CONNECTING A VCR

VCR

AUDIO OUT

VIDEO OUT

VIDEO IN

AUDIO IN

(For playback) (For recording)

VIDEO IN

Video Connection

For playback

Connect a Video cable from the VIDEO IN (VCR) jack on the back of your AV Receiver to the Video Output jack on your VCR.

For recording

Connect a Video cable from the VIDEO OUT (VCR) jack on the back of your AV Receiver to the Video Input jack on your VCR.

Audio Connection

For playback

Connect AUDIO IN (VCR) on your AV Receiver to the Audio Out of the VCR.

For recording

Connect AUDIO OUT (VCR) on your AV Receiver to the Audio In of the VCR.

Disconnect the power plug from the outlet if you will not use this unit for a long period of time.



HW-C700-C770S-C770BS-XAA_0609.in24 24HW-C700-C770S-C770BS-XAA_0609.in24 24 2010-06-09  5:07:062010-06-09  5:07:06

CONNECTING A CD PLAYER

ENG

CD player

COAXIAL OUT

AUDIO OUT

● CONNECTIONS

Audio Connection

Connect the Digital Input (COAXIAL) on your AV Receiver to the Digital Output of the CD Player.

Connect AUDIO IN (CD) on your AV Receiver to the Audio Out of the CD player.

If the CD player has only one audio output jack, connect it to either the right or left audio input jack of the main



unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.

HW-C700-C770S-C770BS-XAA_0609.in25 25HW-C700-C770S-C770BS-XAA_0609.in25 25 2010-06-09  5:07:092010-06-09  5:07:09

Connections

CONNECTING 7.1 CHANNEL DEVICES

You can connect the AV receiver to a DVD player, SUPER AUDIO CD player or other device with 7.1 channel output.

FRONT SURROUND SURROUND

5.1 CH

7.1 CH

SUB WOOFER

CENTER

BACK

7.1 Channel device

HW-C700-C770S-C770BS-XAA_0609.in26 26HW-C700-C770S-C770BS-XAA_0609.in26 26 2010-06-09  5:07:142010-06-09  5:07:14

ENG

CONNECTING AN

You can listen to audio from an iPod through the main unit. For iPod operation with your receiver, see this page and

pages 50 ~ 51.

Connect the iPod dock connector to the iPod jack on your reciever.

Place the iPod in the Dock.

If you want to play a movie stored in your iPod player, you should set the player's TV Out option to

•

On before inserting it into the dock. See page 51.

Press the iPod button on the remote control.

You can also use the INPUT SELECT button on the main unit.

•

The mode switches as follows :

FM  BD/DVD  SAT  TV  VCR  CD  AUX  7.1 MULTI CH  IPOD AUDIO  IPOD VIDEO

iPod

iPOD

● CONNECTIONS

Disconnecting an iPod

Follow the steps below to prevent damage to an iPod and data when disconnecting from your AV receiver.

Press the INPUT SELECT button on the main unit to switch to a mode other than IPOD AUDIO or

IPOD VIDEO.

Turn off the AV Receiver.

Disconnect the iPod player from the iPod dock, or remove the iPod dock connector from the AV

receiver.

You must have the VIDEO (Monitor or VCR) output connected to your TV to view iPod video.



See page 24.

Adjust the volume to a moderate level before you connect your iPod and AV Receiver.



When the unit is powered on and you connect an iPod, the unit will charge your iPod's battery.



Make sure to connect the dock connector so that the label “SAMSUNG” faces upward.



“Made for iPod” means that an electronic accessory has been designed to connect speciﬁ cally to an iPod and



has been certiﬁ ed by the developer to meet Apple performance standards. “Works with iPhone” means that an electronic accessory has been designed to connect speciﬁ cally to an



iPhone and has been certiﬁ ed by the developer to meet Apple performance standards.

HW-C700-C770S-C770BS-XAA_0609.in27 27HW-C700-C770S-C770BS-XAA_0609.in27 27 2010-06-09  5:07:192010-06-09  5:07:19

Connections

CONNECTING AN

iPod models that are compatible with HW-C700/C700B/C770S/C770BS

iPod (Continued)

"Made for iPod" means that the dock has been designed to connect speciﬁ cally for the iPod and has been certiﬁed by the



developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.



iPod is a trademark of Apple Inc., registered in the U.S. and other countries.

iPhone is a trademark of Apple Inc.

HW-C700-C770S-C770BS-XAA_0609.in28 28HW-C700-C770S-C770BS-XAA_0609.in28 28 2010-06-09  5:07:232010-06-09  5:07:23

CONNECTING THE FM ANTENNA

Connect the FM antenna supplied to the FM ANTENNA terminal as a temporary measure.

Slowly move the antenna wire around until you ﬁ nd a location where reception is good, then fasten it to a wall or

2. other rigid surface.

FM antenna (supplied)

ENG

● CONNECTIONS

Do not place the antenna cable close to the power cord. Keep it as far away as possible.



If you experience poor FM reception, use an external antenna.

CONNECTING AUX COMPONENTS

You can connect external devices you use for a short time (camcorder, game console, mobile equipment,etc.) to the front of this unit for convenience.

AUDIO

VIDEO

OUT

Camcorder

HW-C700-C770S-C770BS-XAA_0609.in29 29HW-C700-C770S-C770BS-XAA_0609.in29 29 2010-06-09  5:07:232010-06-09  5:07:23

Basic functions of your AV Receiver

BEFORE USING THE AV RECEIVER

Turning On/Off

Connect the power plug to the outlet.

Press the POWER button on the main unit for 2 seconds.

This unit will be turned on or set to Standby mode.

•

You can also turn the unit on/off by pressing the POWER button on the remote control.

•

Remote control functions

You can operate your AMP (this AV receiver)/ TV and BD(Samsung only)/DVD player with this remote control. See pages 54 ~ 55 for more details.

To select a function

Method 1

Press the INPUT SELECT button.

Each time you press this button, FM  BD/DVD  SAT  TV  VCR  CD  AUX

•

 7.1 MULTI CH  IPOD AUDIO  IPOD VIDEO will be selected in turn.

Method 2

Press the TUNING/CH, BD/DVD, SAT, TV, CD, MULTI CH, VCR/AUX or iPod button.

You can directly select the desired function.

•

AUDIO SETUP

Selecting a source device and connection jack

Select the external devices you have connected to the receiver.

Press the SETUP/MENU button.

Each time the button is pressed, the mode switches

•

between SETUP ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the the ENTER or ► button.

Press the

•

Devices switch as follows; BD/DVD, SAT, TV, CD

- To exit setup mode -

•

Press the SETUP/MENU button. SETUP OFF appears on the display and Setup Mode is exited.

You can also use the SETUP, ,,.,<, >, ENTER buttons on the front of your AV Receiver.



▲▼

buttons to select AUDIO SETUP, and then press

▲▼ buttons

to select a desired jack.

HW-C700-C770S-C770BS-XAA_0609.in30 30HW-C700-C770S-C770BS-XAA_0609.in30 30 2010-06-09  5:07:322010-06-09  5:07:32

SELECTING DIGITAL/ANALOG INPUT

AMP/TV

BD/

ENG

You can listen to sound in 2 channel analog , Dolby Digital or DTS using this unit.

Press the INPUT SELECT button to select a desired function (BD/DVD, SAT,TV,

CD, AUX). See page 30.

Press the AUDIO ASSIGN button on the remote control to select the external

device you have connected.

•

Each time you press this button, the input mode changes as follows:

For BD/DVD function

•

Ä Ä

For SAT function

•

Ä Ä

For TV function

•

Ä Ä

DIMME

INPUT SELECT

TV SOURCE

DVD

POWER

POWE

AMP/TV DIMMER BD/DVD

456

● BASIC FUNCTIONS OF YOUR AV RECEIVER

For CD function

•

For AUX function

•

You can also change the input mode by pressing the AUDIO ASSIGN button on the front of your AV Receiver.



You can enjoy Dolby Digital or DTS if you connect the digital audio output jack of an external audio component to the optical



or coaxial digital audio input jack on the main unit.

HW-C700-C770S-C770BS-XAA_0609.in31 31HW-C700-C770S-C770BS-XAA_0609.in31 31 2010-06-09  5:07:322010-06-09  5:07:32

Setup

For your convenience, you can set this AV receiver's features for the best use.

SETUP MENU TREE

Here’s a quick look at how the setup menus are organized on your AV Receiver.

AUDIO SETUP

BD/DVD

OPT 1,2,3

SAT

OPT 1,2,3

COAX

SPK SIZE

SPK DISTANCE

SPK LEVEL TEST TONE

DPLIIX SETUP

DPLIIZ SETUP TONE CONTROL NEO:6 SETUP

EX/ES SETUP

A/V SYNC

MP3 ENHANCER

SMART VOLUME

ASC SETUP

DRC SETUP HDMI SETUP

VARIABLE SET

HW-C700-C770S-C770BS-XAA_0609.in32 32HW-C700-C770S-C770BS-XAA_0609.in32 32 2010-06-09  5:07:352010-06-09  5:07:35

SETUP MENU TREE (Continued)

ENG

AUDIO SETUP

SPK SIZE

SPK DISTANCE

SPK LEVEL

FRONT

CENTER

SURR

SBACK

FRONTH

SUBW

CROVR

F.L

F.R

CEN

S.L

S.R

SBL/FHL

SBR/FHR

S.W

F.L

F.R

CEN

S.L

S.R

SBL/FHL

SBR/FHR

S.W

LARGE SMALL

● SETUP

LARGE NONESMALL

YES NO

60Hz, 80Hz, 100Hz, 120Hz, 150Hz, 180Hz, 200Hz

1 ~ 30 FT (1 foot steps) , default : 10 FT

-10 ~ +10dB (1dB step) , default : 00dB

TEST TONE

DPLIIX SETUP

DPLIIZ SETUP TONE CONTROL NEO:6 SETUP

EX/ES SETUP

A/V SYNC

MP3 ENHANCER

SMART VOLUME

ASC SETUP DRC SETUP HDMI SETUP

VARIABLE SET

If Dolby Pro Logic IIz is set to On, the Surround Back speaker (SBL/SBR) is changed



to the Front Height Speaker (FHL/FHR).

AUTO MANUAL

HW-C700-C770S-C770BS-XAA_0609.in33 33HW-C700-C770S-C770BS-XAA_0609.in33 33 2010-06-09  5:07:352010-06-09  5:07:35

Setup

SETUP MENU TREE (Continued)

AUDIO SETUP

SPK SIZE

SPK DISTANCE

SPK LEVEL

TEST TONE

DPLIIX SETUP

DPLIIZ SETUP

TONE CONTROL

NEO:6 SETUP

PANORAMA

DIMENSION

C- WIDTH

HEIGHT

TONE

BASS

TREBLE

C-IMAGE

OFF

-7 ~ 0 ~ +7

0~7

OFF ON

-6dB ~ +6dB (1dB Step)

0~5

AUTO OFF ONEX/ES SETUP

A/V SYNC

MP3 ENHANCER

SMART VOLUME

ASC SETUP DRC SETUP HDMI SETUP

VARIABLE SET

HW-C700-C770S-C770BS-XAA_0609.in34 34HW-C700-C770S-C770BS-XAA_0609.in34 34 2010-06-09  5:07:352010-06-09  5:07:35

SETUP MENU TREE (Continued)

AUDIO SETUP

SPK SIZE

SPK DISTANCE

SPK LEVEL

TEST TONE

DPLIIX SETUP

DPLIIZ SETUP

TONE CONTROL

NEO:6 SETUP

EX/ES SETUP

ENG

● SETUP

A/V SYNC

MP3 ENHANCER

SMART VOLUME

ASC SETUP

HDMI SETUP

VARIABLE SET

SYNC OFF ~ SYNC 240MS (10MS Step)

OFF ON

START EQ ON / EQ OFF

MAX STD MINDRC SETUP

SYNC

ON OFF

AUDIO

AVR TV

ANYNET+

ON OFF

OFF ON

HW-C700-C770S-C770BS-XAA_0609.in35 35HW-C700-C770S-C770BS-XAA_0609.in35 35 2010-06-09  5:07:352010-06-09  5:07:35

Setup

SETTING THE SPEAKER SIZE

Signal outputs and frequency response from the speaker will be adjusted according to your speaker conﬁ guration and whether certain speakers are used or not.

Press the SETUP/MENU button.

•

Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the ►

Press the ENTER or ► button.

•

Press the selected speaker.

Repeat steps 3-5 to set the mode for each speaker.

- To exit setup mode -

•

Press the SETUP/MENU button. SETUP OFF appears on the display and Setup Mode is exited.

Setting the Speaker

▲▼

buttons to select SPK SIZE, and then press the ENTER or

button.

▲▼

buttons to select the speaker you want, and then press the

▲▼

Each time you press the SBACK Æ FRONTH Æ SUBW Æ CROVR will be selected in turn.

▲▼

buttons to set the mode (LARGE, SMALL etc.) for the

buttons, FRONTÆCENTER Æ SURR Æ

SPEAKER Possible Settings Default Setting

FRONT (Front) LARGE, SMALL SMALL

CENTER (Center) LARGE, SMALL, NONE SMALL

SURR (Surround) LARGE, SMALL, NONE SMALL

SBACK (Surround Back) LARGE, SMALL, NONE SMALL

FRONTH (Front Height) LARGE, SMALL, NONE NONE

SUBW (Subwoofer) YES, NO YES

CROVR (Crossover Frequency) 60, 80, 100,120, 150, 180, 200(Hz) 100Hz

•

LARGE : Select when using large speakers. You can listen to full range sound.

•

SMALL : Select this when using small speakers.

•

NONE : Select when no speaker is used.

•

YES (subwoofer) : Select when using the subwoofer speaker.

•

NO (subwoofer) : Select when not using the subwoofer speaker.

•

CROVR : Select the crossover frequency for the best bass response in your room.



You can also use the SETUP, ,,., <, >, ENTER buttons on the front of your AV Receiver.

When the Front speaker is only set to LARGE, you can select LARGE of other speakers.



When the Surround speaker is only set to LARGE, you can select LARGE of SBACK (Surround Back)



speaker.

HW-C700-C770S-C770BS-XAA_0609.in36 36HW-C700-C770S-C770BS-XAA_0609.in36 36 2010-06-09  5:07:362010-06-09  5:07:36

SETTING THE SPEAKER LISTENING DISTANCE

If the speakers cannot be placed at equal distances from the listening position, you can adjust the delay time of the audio signals from the center and surround speakers.

Press the SETUP/MENU button.

•

Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the ENTER or ► button.

Press the the ENTER or ► button.

•

Press the

•

▲▼

buttons to select SPK DISTANCE, and then press the

▲▼

buttons to select the speaker you want, and then press

Each time you press the ▲▼ buttons, F.L Æ F.RÆ CEN Æ S.L Æ S.R Æ SBL Æ SBR Æ S.W will be selected in turn.

▲▼

buttons to set the Speaker Distance.

For the FRONT LEFT, FRONT RIGHT, CENTER, SURR. LEFT, SURR. RIGHT, SURRBACK.LEFT, SURRBACK.RIGHT and SUBWOOFER Speakers, you can set the distance from the speaker to listening position between 1ft ~ 30ft (0.3~9.0m) in intervals of 1ft (0.3m).

ENG

● SETUP

- To exit setup mode -

•

Press the SETUP/MENU button. SETUP OFF appears on the display and Setup Mode is exited.

- Setting Speaker Distance -

Set the distance from the speaker to listening position in intervals of 1ft(0.3m).

• F.L (front left) : 1ft ~ 30ft • SW (subwoofer) : 1ft ~ 30ft

• F.R (front right) : 1ft ~ 30ft • SBL (surround back left) : 1ft ~ 30ft

• S.L (surround left) : 1ft ~ 30ft • SBR (surround back right) : 1ft ~ 30ft

• S.R (surround right) : 1ft ~ 30ft • FHL (front height left) : 1ft ~ 30ft

• CEN (center) : 1ft ~ 30ft • FHR (front height right) : 1ft ~ 30ft



If the listening position is beyond the range of the speaker distance setup, set the speaker distance to the maximum.



The distance range of the overall speaker system is determined based on the F.L (front left) speaker distance from the listening position.



If Dolby Pro Logic IIz is set to On, the Surround Back speaker (SBL/SBR) is changed to the Front Height Speaker (FHL/FHR).

HW-C700-C770S-C770BS-XAA_0609.in37 37HW-C700-C770S-C770BS-XAA_0609.in37 37 2010-06-09  5:07:362010-06-09  5:07:36

Setup

SETTING THE SPEAKER LEVEL

You can set the balance and level of speakers.

Press the SETUP/MENU button.

Each time the button is pressed, the mode switches between SETUP

•

ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the

or ► button.

Press the the ENTER or ► button.

•

Press the ▲▼ buttons to set the Speaker Level mode.

•

▲▼

buttons to select SPK LEVEL, and then press the ENTER

▲▼

buttons to select the speaker you want, and then press

Each time you press this button, F.L Æ F.RÆ CEN Æ S.L Æ S.R Æ SBL Æ SBR Æ S.W will be selected in turn.

You can adjust it from -10 to +10dB in 1 step increments. The sound gets quieter at -10dB and louder at +10dB.

- To exit setup mode -

•

Press the SETUP/MENU button. SETUP OFF appears on the display and Setup Mode is exited.

- Setting Speaker Level -

• F.L (front left) : -10 ~ +10dB • SW (subwoofer) : -10 ~ +10dB

• F.R (front right) : -10 ~ +10dB • SBL (surround back left) : -10 ~ +10dB

• S.L (surround left) : -10 ~ +10dB • SBR (surround back right) : -10 ~ +10dB

• S.R (surround right) : -10 ~ +10dB • FHL (front height left) : -10 ~ +10dB

• CEN (center) : -10 ~ +10dB • FHR (front height right) : -10 ~ +10dB

If Dolby Pro Logic IIz is set to On, the Surround Back speaker (SBL/SBR) is changed to the Front Height



Speaker (FHL/FHR).

HW-C700-C770S-C770BS-XAA_0609.in38 38HW-C700-C770S-C770BS-XAA_0609.in38 38 2010-06-09  5:07:362010-06-09  5:07:36

SETTING THE TEST TONE

Use the test tone to check the speaker connection status or level.

Press the SETUP/MENU button.

•

Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the or ► button.

Press the ENTER or ► button.

•

▲▼

buttons to select TEST TONE, and then press the ENTER

▲▼

buttons to select the option you want, and then press the

AUTO : Test signal will be automatically output as follows; F.L Æ CEN Æ S.W Æ F.R Æ S.R Æ SBR Æ SBL Æ S.L.

- During test tone output, press the output level from -10 to +10 dB by 1 step.

MANUAL : Enables you to adjust the output level of the speaker manually.

1) Press the

Each time you press the Æ S.R Æ SBR Æ SBLÆ S.L will be selected in turn.

ENTER

button to select the speaker you want.

ENTER

▲▼

buttons to adjust the speaker

button, F.L Æ CEN Æ S.W Æ F.R

ENG

● SETUP

2) Press the You can adjust the speaker output level from -10 to +10dB by 1 step. The sound gets quieter at -10dB and louder at +10dB.

- Test Tone Output -

• F.L (front left) : -10 ~ +10dB • CEN (center) : -10 ~ +10dB

• F.R (front right) : -10 ~ +10dB • S.W (subwoofer) : -10 ~ +10dB

• S L (surround left) : -10 ~ +10dB • SBL (surround back left) : -10 ~ +10dB

• S.R (surround right) : -10 ~ +10dB • SBR (surround back right) : -10 ~ +10dB

- To stop test tone -

•

Press the SETUP/MENU button once. SETUP OFF appears on the display and test tone stops.



In the Dolby Pro Logic IIz mode, test signal will be automatically output as follows : F.L Æ FHL Æ CEN Æ S.W Æ FHR Æ F.R Æ S.R.

▲▼

buttons to set the Test Tone mode you want.

HW-C700-C770S-C770BS-XAA_0609.in39 39HW-C700-C770S-C770BS-XAA_0609.in39 39 2010-06-09  5:07:362010-06-09  5:07:36

Setup

SETTING DOLBY PRO LOGIC MODE

This mode provides 7.1 channel sound from 2 channel sources. Press the PROLOGIC button on the remote control.

MOVIE : Adds realism to the movie soundtrack.

•

MUSIC : Provides 7.1 channel surround sound for digital, analog or existing stereo sources.

•

GAME : Enhances the excitement of the game’s sound.

•

MATRIX : You will hear 7.1 channel surround sound.

•

PL (Pro Logic) : You will experience a surround effect with 5.1 channel surround sound.

•

SETTING DOLBY PRO LOGIC IIx

This function works only in Dolby Pro Logic IIx MUSIC mode.

Press the SETUP/MENU button.

•

Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the ENTER or ► button.

•

▲▼

buttons to select DPLIIX SETUP, and then press the

▲▼

buttons to select the option you want, and then press the

PANORAMA : You can set it ON or OFF. (This mode extends the front stereo image to include the surround speakers for an exciting "wraparound" effect with side wall imaging.)

DIMENSION : You can set from -7 to +7. (Incrementally adjusts the sound ﬁ eld (DSP)from the front or surround.)

C- WIDTH : You can set from 0 to 7. (This sets the width of the center sound image. The higher the setting, the less sound comes from the center speaker.)

PANORAMA, DIMENSION and CENTER WIDTH settings are enabled only if the mode is set to MUSIC.



You cannot use Dolby Pro Logic llx mode for multi channel signals such as Dolby Digital, Dolly Digital +,



Dolby true HD, DTS, DTS-HD Master Audio.

Pro Logic works only for PCM audio signals with sampling frequencies of 32KHz, 44KHz or 48KHz.



When Dolby Pro Logic IIz is set ON, Dolby Pro Logic IIx can not be used.



HW-C700-C770S-C770BS-XAA_0609.in40 40HW-C700-C770S-C770BS-XAA_0609.in40 40 2010-06-09  5:07:372010-06-09  5:07:37

SETTING DOLBY PRO LOGIC IIz

Dolby Pro Logic IIz adds front height channels to surround sound.

Press the SETUP/MENU button.

Each time the button is pressed, the mode switches between SETUP

•

ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the

ENTER or ► button.

Press the

•

▲▼

buttons to select DPLIIZ SETUP, and then press the

▲▼

buttons.

Each time you press this button, HEIGHT OFF Æ HEIGHT ON will be selected in turn.

If Dolby Pro Logic IIz is set to On, the Surround Back speaker in the speaker size mode is changed to NONE,



the Front Height Speaker will be turned on. If Dolby Pro Logic IIz is set to OFF, the surround back speaker and front height speaker can't be turned to default setting.

If you change Dolby Pro Logic IIz mode to Dolby Pro Logic IIx mode, ﬁ rst Dolby Pro Logic IIz will be



turned off, second FRONTH in the speaker size mode will be turned off, lastly the Surround Back Speaker will be turned on. If you turn Dolby Pro Logic IIz on, FRONTH in the speaker size mode and the Surround Back Speaker can not be changed to NONE.

ENG

● SETUP

SETTING TONE CONTROL

This will enable you to adjust the bass and treble level.

Press the SETUP/MENU button.

Each time the button is pressed, the mode switches between SETUP

•

ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the

ENTER or ► button.

Press the ENTER or ► button.

•

Press the ▲▼ buttons to set the Tone Control mode you want.

•

- To exit setup mode -

•

Press the SETUP/MENU button. SETUP OFF appears on the display and Setup Mode is exited.

▲▼

buttons to select TONE CONTROL, and then press the

▲▼

buttons to select the option you want, and then press the

Each time you press this button, TONE Æ BASS Æ TREBLE will be selected in turn.

If it is set to TONE OFF, the Tone Control function will be disabled. You can adjust it from -6 to +6dB by 1 step. The sound gets quieter at -6dB and louder at +6dB.

The Tone Control function can be applied to all channels except for the subwoofer.



HW-C700-C770S-C770BS-XAA_0609.in41 41HW-C700-C770S-C770BS-XAA_0609.in41 41 2010-06-09  5:07:372010-06-09  5:07:37

Setup

SETTING NEO:6 MODE

You can play back 2 channel sound over 6.1 channels when enjoying music or a movie.

Press the SETUP/MENU button.

Each time the button is pressed, the mode switches between SETUP

•

ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the

ENTER or ► button.

Press the You can set C-IMAGE from 0 to 5 This parameter adjusts the height of the center image through the front and center speakers. “0” is the lowest while “5” is the highest.

- To exit setup mode-

•

Press the SETUP/MENU button. SETUP OFF appears on the display and Setup Mode is exited.

▲▼

buttons to select NEO:6 SETUP, and then press the

▲▼

buttons to set the C-IMAGE mode you want.

NEO:6 mode cannot be used with Dolby Digital, Dolly Digital +, Dolby true HD, DTS, DTS-HD Master Audio.



Pro Logic works only for PCM audio signals with sampling frequencies of 32KHz, 44KHz or 48KHz.



HW-C700-C770S-C770BS-XAA_0609.in42 42HW-C700-C770S-C770BS-XAA_0609.in42 42 2010-06-09  5:07:382010-06-09  5:07:38

SETTING EX/ES MODE

When surround back speakers are connected, you can listen to 6.1 or 7.1 multi-channel sound using the built-in Dolby Digital Surround EX or DTS ES decoder. This function works when a Dolby Digital or DTS source (such as a DVD player) is input, and does not work with L.PCM and Dolby Digital 2 channel sources.

Press the SETUP/MENU button.

Each time the button is pressed, the mode switches between SETUP

•

ENTER and SETUP OFF.

Press

- To exit setup mode-

the ENTER

Press the ENTER or ► button.

Press the

•

▲▼

AUTO : If the unit receives an audio signal that it can recognize, it will select an optimal decoder for playback in 6.1/7.1 channels. If the ampliﬁ er does not recognize the audio signal, it will not play in

6.1/7.1 channel automatically. ON : Dolby Digital or DTS signal will be played in 6.1 / 7.1 channel using

Dolby Digital Surround EX / DTS ES decoder. OFF : Dolby Digital Surround EX / DTS ES decoder will not be used for playback.

Press the SETUP/MENU button. SETUP OFF appears on the display and Setup Mode is exited.

button to select SETUP ENTER.

buttons to select EX/ES SETUP, and then press the

buttons to set the EX/ES mode you want.

ENG

● SETUP



You cannot use DTS-ES without surround back speakers connected.

HW-C700-C770S-C770BS-XAA_0609.in43 43HW-C700-C770S-C770BS-XAA_0609.in43 43 2010-06-09  5:07:382010-06-09  5:07:38

Setup

AV SYNC

Video may look slower than the audio if it is connected to a digital TV. If this occurs, adjust the audio delay time to match the video.

Press the SETUP/MENU button.

Each time the button is pressed, the mode switches between SETUP

•

ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the ▲▼ buttons to select A/V SYNC, and then press the ENTER

or ► button.

Press the ▲▼ buttons to set the A/V Sync mode you want.

You can adjust it from OFF to 240MS in 10MS steps.

•

MP3 ENHANCER

This also helps enhance your sound experience (ex. mp3 music). Use this if you want to hear better sound from a low quality mp3 source.

Press the SETUP/MENU button.

•

Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the ▲▼ buttons to select MP3 ENHANCER, and then press the ENTER or ► button.

Press the ▲▼ buttons to select ON or OFF.

SMART VOLUME

This will regulate and stabilize the volume level against a drastic volume change when changing channels or during a scene transition.

Press the SETUP/MENU button.

•

Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the ▲▼ buttons to select SMART VOLUME, and then press the ENTER or ► button.

Press the ▲▼ buttons to select ON or OFF.

HW-C700-C770S-C770BS-XAA_0609.in44 44HW-C700-C770S-C770BS-XAA_0609.in44 44 2010-06-09  5:07:382010-06-09  5:07:38

ASC (AUTO SOUND CALIBRATION) SETUP

By setting the ASC function just once when you relocate or install the unit, you can have the unit automatically recognize the distance between speakers, levels between channels, and frequency characteristics to create a

7.1-channel sound ﬁ eld optimized for your environment.

- Before Setting -

Plug the ASC microphone into the ASC MIC jack.

Place the ASC microphone at the listening position.

Press the ASC button on the front panel, and then press the ENTER button.

Press the SETUP/MENU button.

Each time the button is pressed, the mode switches between SETUP

•

ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the ▲▼ buttons to select ASC SETUP, and then press the

ENTER or ► button.

Press the ▲▼

ENTER button.

•

To create the optimal 7.1 channel sound ﬁ eld, the selections are in the following sequence:

L ➞ C ➞ R ➞ SR ➞ SBR ➞ SBL ➞ SL ➞ SW

•

EQ ON : The ASC(Auto Sound Calibration) EQ mode is set to on.

EQ OFF: The ASC(Auto Sound Calibration) EQ mode is set to off.

buttons

to select ASC START, and then press the

ENG

● SETUP

If you see a ASC READY message on the screen, press the ENTER button to apply the measurement value. And then unplug the ASC microphone.

ASC

Microphone

To cancel the ASC (Auto Sound Calibration) setup.

This will be automatically reverted if you press the RETERN button.

* If ASC error occurs, see "ASC Error List" on page 58.

Setting the ASC function takes about 3 minutes.



Because the volume level of the tone is ﬁ xed during the ASC setup, you cannot adjust the volume using the volume control. If the ASC microphone is disconnected during the ASC setup, the setup will be canceled.



You can also press the ASC button on the remote control to use this function.



If Dolby Pro Logic IIz is set to ON, the selection are in the following sequence : FL Æ CEN Æ FR Æ SR Æ SL Æ SW.



HW-C700-C770S-C770BS-XAA_0609.in45 45HW-C700-C770S-C770BS-XAA_0609.in45 45 2010-06-09  5:07:392010-06-09  5:07:39

Setup

DRC SETUP

You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night.DRC compresses the audio to make the loudest sounds quieter and the quietest sounds louder.

Press the SETUP/MENU button.

•

Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the ▲▼ buttons to select DRC SETUP, and then press the ENTER or ► button.

Press the ▲▼ buttons to set the DRC Setup mode you want.

•

STD : Sets DRC effect to standard. •MAX : Sets DRC effect to maximum.

•

MIN : Sets DRC effect to minimum.

HDMI SETUP

Use this if you want to receive audio from HDMI connected external devices.

Press the SETUP/MENU button.

•

Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.

Press the ENTER button to select SETUP ENTER.

Press the ▲▼ buttons to select HDMI SETUP, and then press the ENTER or ► button.

Press the ▲▼ buttons to select the option you want, and then press the ENTER or ► button.

Press the ▲▼ buttons to set the HDMI Setup mode you want.

•

HDMI AUDIO : AVR(Audio Video Receiver), TV

This preference determines whether audio received at the HDMI IN is output by the HDMI OUT. If you want to listen to audio from an HDMI connected external device through your HDMI connected TV's speakers, set it to TV. Otherwise, leave it on AVR to listen to audio from the A/V receiver.

- AVR : HDMI audio is not output - TV : HDMI audio is output

•

HDMI ANYNET+ : ON, OFF

Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's remote control.

- ON : Anynet+ is enabled. - OFF : Anynet+ is disabled.

•

HDMI SYNC : ON, OFF

The AV receiver can be set to automatically correct any delay between the video and the audio, based on the data from the connected TV.

- ON : HDMI Sync is enabled. - OFF : HDMI Sync is disabled.

HDMI Audio is enabled only if both the HDMI INPUT and HDMI OUT are connected properly and working normally.



This function works only if your HDMI-compatible TV supports HDMI Sync.



VARIABLE SET (Low Power Consumption SETUP)

This function enhances electric power efﬁ ciency.

Press the SETUP/MENU button.

Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.

•

Press the ENTER button to select SETUP ENTER.

Press the ▲▼ buttons to select VARIABLE SET, and then press the ENTER or ► button.

Press the ▲▼ buttons to select ON or OFF.

ON :This is Samsung's electric power efﬁ ciency function, you can save about 30 % for power consumption.

•

OFF: Normal power efﬁ ciency function.

•

This function is not available after the Tone Control, Speaker Level, SFE mode or ASC is changed from the factory setting.



HW-C700-C770S-C770BS-XAA_0609.in46 46HW-C700-C770S-C770BS-XAA_0609.in46 46 2010-06-09  5:07:402010-06-09  5:07:40

Operation

USING THE SURROUND MODES

Using the SOUND EFFECT button on the front of the main unit

Selecting the DPLIIx mode

Press the SOUND EFFECT button to select DPLIIX.

Each time you press this button, DPLIIX Æ NEO:6 Æ SFE will be selected in turn.

•

Press the

•

Selecting the NEO:6 mode

Press the SOUND EFFECT button brieﬂ y to select NEO:6.

•

Press the

•

UP/DOWN ( ,,. ) button.

Each time you press the MOVIE will be selected in turn.

You can also select the DPLIIx mode by pressing the PROLOGIC button on the remote control.

Each time you press this button, DPLIIX Æ NEO:6 Æ SFE will be selected in turn.

UP/DOWN ( ,,. ) button.

Each time you press the You can also select the NEO:6 mode by pressing the NEO : 6 button on the remote control.

UP/DOWN ( ,,. ) button, MUSIC Æ GAME Æ MATRIX Æ PL Æ

UP/DOWN ( ,,. ) button, MUSIC Æ CINEMA will be selected in turn.

ENG

● OPERATION

Selecting the SFE mode

Press the SOUND EFFECT button to select SFE.

Each time you press this button, DPLIIX Æ NEO:6 Æ SFE will be selected in turn.

•

Press the

•

UP/DOWN ( ,,. ) button.

Each time you press the Æ CHURCH Æ ROCK Æ CLASSIC Æ LIVE Æ GAME Æ MOVIE Æ CONCERT Æ STADIUM will be selected in turn.

You can also select the SFE mode by pressing the DSP button on the remote control.

You cannot use Dolby Pro Logic llx mode for multi channel signals such as Dolby Digital and DTS.



Pro Logic works only for BITSTREAM audio signals with sampling frequencies of 32KHz, 44KHz or



48KHz.

If you turn Dolby Pro Logic IIz on, the Dolby Pro Logic IIx mode is only available MOVIE.



UP/DOWN ( ,,. ) button, STEREO Æ HALL 1Æ HALL 2 Æ J.CLUB

Using the S.DIRECT/STEREO button on the front of the main unit

Press the S.DIRECT/STEREO button.

Each time the button is pressed, the mode switches between the S. DIRECT mode and the STEREO

•

mode.

•

S.DIRECT : Outputs 2 CH PCM audio signal without any signal processing, providing higher audio quality. This is useful for obtaining the best sound from a connected CD player.

•

STEREO : Outputs sound of the selected source in 2 CH stereo.

HW-C700-C770S-C770BS-XAA_0609.in47 47HW-C700-C770S-C770BS-XAA_0609.in47 47 2010-06-09  5:07:402010-06-09  5:07:40

Operation

USING THE SURROUND MODES

Surround Mode and Input Signal Chart

o = active, – = inactive

Surround Mode Input Signal Decoding

Dolby D Surr. EX Dolby Digital 5.1

Dolby D (5.1ch) Dolby Digital 5.1 Dolby D Surr.EX Pro Logic IIz

DOLBY

NEO:6

SFE

EX/ES

STEREO

True-HD True-HD True-HD Dolby

Digital +

DTS-HD

Dolby D(5.1ch) Pro Logic IIz

Dolby D (2ch) Pro Logic IIx(z)

Dolby D (2ch Surr) Pro Logic IIx(z)

L.PCM (Audio) Pro Logic IIx(z)

Analog Pro Logic IIx(z)

L.PCM (Audio) Neo:6

Analog Neo:6

Dolby D (2ch) Neo:6

Dolby D (2ch Surr) Neo:6

Dolby D (2ch) DD+SFE

Dolby D (2ch Surr) DD+SFE

L.PCM (Audio) SFE

Analog SFE

Dolby D Surr. EX Dolby Digital EX

Dolby D (5.1ch) Dolby Digital EX

DTS-ES DTS-ES

DTS (5.1ch) DTS-ES

Dolby D (2ch) Stereo

Dolby D (2ch Surr) Stereo

L.PCM (Audio) Stereo L.PCM 96KHz Stereo

Analog Stereo

Dolby Digital +

Master Audio Master Audio

High Resolution High Resolution

Dolby Digital +

L/R C

OOOO O OOO– O OOOO O OOOO O OOOO O OOOO O OOOO O OOOO O OOOO O OOOO O OOOO O OOOO O OOO– O OOO– O OOO– O OOO– O OOOO O OOOO O OOOO O OOOO O O–– – O O–– – O O–– – O O–– – O O–– – O OOOO O

OOOO O

OOOO O OOOO O

(Continued)

Output Channel Display Information

SLSRSBL

SBR

SUBW

Display Signal

Format DIGITAL DIGITAL DIGITAL DIGITAL DIGITAL DIGITAL

L.PCM

Analog

L.PCM

Analog DIGITAL DIGITAL DIGITAL DIGITAL

L.PCM

Analog DIGITAL DIGITAL

dts, ES

dts DIGITAL DIGITAL

L.PCM L.PCM Analog

True-HD

Dolby Digital +

DTS-HD DTS-HD

Channel Status

L, C, R, SL, SR, SBL, SBR, SW

L, C, R, SL, SR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW

L, R, SW L, R, SW L, R, SW L, R, SW L, R, SW

L, C, R, SL, SR, SBL, SBR, SW

L, C, R, SL, SR, SBL, SBR, SW L, C, R, SL, SR, SBL, SBR, SW

L/R : front speaker (left/right)

•

C : center speaker SL/SR : surround speaker (left/right) SBL/SBR : surround back speaker (left/right) SW : subwoofer

Channel status displays are dependent on the speaker conﬁ guration.



SFE mode works with 2-ch signals.



If Dolby Pro Logic IIz is set to On, the Surround Back speaker(SBL/SBR) is changed to the Front Height



Speaker(FHL/FHR), Dolby true HD, Dolby plus, DTS-HD Master Audio ,SFE and NE0:6 will be output 5.1 channel.

USING THE SUBWOOFER SELECTION BUTTON

You can set the subwoofer to on/off.

Press the SUBWOOFER button.

HW-C700-C770S-C770BS-XAA_0609.in48 48HW-C700-C770S-C770BS-XAA_0609.in48 48 2010-06-09  5:07:402010-06-09  5:07:40

LISTENING TO THE RADIO

You can listen to the radio by using either automatic or manual tuning.

Press the INPUT SELECT button to select FM.

Select a frequency (radio broadcast).

Preset tuning :

• Press the #,$ buttons on the remote control to select the preset frequency.

•

Manual tuning 1 (Automatic tuning): Press and hold the TUNING/CH ( .,, ) buttons on the remote control to automatically tune in a frequency.

•

Manual tuning 2 : Press the TUNING/CH ( .,, ) buttons on the remote control to increase or decrease the frequency step by step.



To Listen in mono/stereo

Press the MO/ST button on the remote control.

•

You can also use the SELECT (.,,) button on the main uint to change the radio frequency.

Each time you press this button, STEREO or MONO will be selected in turn. If you select MONO in an area with weak reception, it will help to reduce noise. This function works only with the remote control.

ENG

● OPERATION

Presetting radio stations

You can preset up to 30 FM stations.

E.g.: Setting station FM 89.10 in preset 2.

Press the INPUT SELECT button to select FM.

Press the TUNING/CH ( .,, ) buttons on the remote control

to select 89.10.

Refer to step 2 above to tune in automatically and manually.

•

Press the MEMORY button on the main unit.

You can also use the TUNER MEMORY button on the

•

remote control. Tuner number will blink on the display.

•

Press the TUNING/CH ( .,, ) buttons on the remote control

to select preset 2.

You can select from presets 1 to 30.

•

Press the MEMORY button on the main unit.

Tuner number will disappear and station 89.10 will be

•

saved in preset 2.

To preset other stations, repeat steps 2 to 5.

To Listen to Preset Station

•

Press the TUNING MODE button to select PRESET and press the SELECT ( .,, ) buttons.

HW-C700-C770S-C770BS-XAA_0609.in49 49HW-C700-C770S-C770BS-XAA_0609.in49 49 2010-06-09  5:07:402010-06-09  5:07:40

Operation

USING AN

You can enjoy playback of your iPod using the supplied remote control.

iPod

Listening to Music (iPod audio function)

You can play music ﬁ les stored in the iPod player by connecting it to the AV receiver.

Connect the iPod dock connector to the iPod jack on the AV

Receiver.

Place the iPod in the dock.

Your iPod is automatically turned on.

•

Press the INPUT SELECT button on the remote control to select IPOD AUDIO mode.

Press the

•

You can use the remote control to control simple playback functions such as the PLAY, PAUSE, STOP, SKIP (#,$) buttons.

PLAY

button on the remote control to play.

The AV receiver starts playing from the ﬁ rst track of the iPod player.

See page 28 for compatible iPods.



Compatibility depends on the software version of your iPod. You can also select iPod by pressing the iPod button on the remote control.



HW-C700-C770S-C770BS-XAA_0609.in50 50HW-C700-C770S-C770BS-XAA_0609.in50 50 2010-06-09  5:07:402010-06-09  5:07:40

ENG

USING AN

Watching a Movie (iPod Video function)

You can play video ﬁ les stored in the iPod player on a TV by connecting it to the AV receiver.

Connect the iPod dock connector to the iPod jack on the AV receiver.

In the iPod screen, move to Videos > Settings and set the TV Out option to On.

Place the iPod in the dock.

Press the INPUT SELECT button on the remote control to select IPOD VIDEO mode.

Set the AV IN option of the TV connected to the AV receiver to COMPOSITE.

Follow the iPod onscreen guide through the following steps.

Press the S,T buttons on the remote control to select Videos and press the ENTER button.

Press the S,T buttons on the remote control to select Movies and press the ENTER button.

Press the S,T buttons to select the ﬁ le to play and press the ENTER button.

•

iPod

(Continued)

The iPod's video ﬁ les will be played on the TV screen.

● OPERATION

You can use the remote control to control simple playback functions such as the PLAY, PAUSE, STOP, SKIP (#,$) buttons.

•

If you press the PREV button within 3 seconds after the playback, the player will stop playing and return to the list screen. If you press the PREV button 3 seconds or later after the playback, the player will move to the start screen of the current ﬁ le.

•

Press the STOP button to stop playing and return to the list screen.

•

Press the RETURN button to return to the previous menu.

You must have the VIDEO (Monitor or VCR) output connected to your TV to view iPod video.



See page 28 for compatible iPods.



Compatibility depends on the software version of your iPod. When the current ﬁ le is played to the end, the next ﬁ le will not be played automatically.



To play the next ﬁ le, select a ﬁ le to play in the list screen of the iPod player. No other screen than the playback one will appear on the TV screen. Check other screens on



the iPod player.

HW-C700-C770S-C770BS-XAA_0609.in51 51HW-C700-C770S-C770BS-XAA_0609.in51 51 2010-06-09  5:07:402010-06-09  5:07:40

Operation

VOL

/CH

SOURCE

CONVENIENT FUNCTIONS

Sleep timer function

You can set the time that this unit will shut itself off.

Press the SLEEP button.

SLEEP : OFF Æ 15 Æ 30 Æ 45 Æ 60 Æ 90 Æ 120 M (MIN) will be

•

selected in turn.

To check sleep timer

Press the SLEEP button.

The remaining time before this unit will shut itself off is shown on the display.

•

Pressing the button again changes the sleep time from what you set previously.

•

To cancel sleep timer

Press the SLEEP button until SLEEP OFF appears on the display.

•

Mute function

This function is useful when answering a doorbell or telephone call.

456

NEO : 6

NEO :

SLEEP

PROLOGIC AUDIO ASSIGN

PROLOGI

UDIO ASSIG

DSP

Press the MUTE button.

•

MUTE appears on the display.

To output sound again

Press the MUTE button again.

•

MUTE will disappear and sound will output.

Adjust the display

You can adjust the brightness of the display.

Press the DIMMER button.

•

Each time you press this button, the brightness changes as follows : Dark Æ Bright.

SLEEP, Mute and the Adjust Display functions can only be operated with the remote control.



MUTE

TUNING

ASC

UNIN

INPUT SELECT

INPUT SELE

TV SOURCE

VOL

POWER

POWE

AMP/TV DIMMER BD/DVD

MP/TV BD/DVD

/CH

HW-C700-C770S-C770BS-XAA_0609.in52 52HW-C700-C770S-C770BS-XAA_0609.in52 52 2010-06-09  5:07:402010-06-09  5:07:40

Reset function

NEO

PROLOGICAUDIO ASSIGN

SUBWOO

MO/ST

RETURN

EXIT

When the Power is on,

Press the MUTE button.

•

MUTE appears on the display.

Press the 9 button ﬁ ve times and then press the ENTER button.

•

INITIAL : NO appears on the display.

Press the

•

When the Power is Off,

Press and hold the MEMORY button on the front of your AV Receiver for longer than 5 seconds.

•

▲▼

buttons to select YES.

The unit will turn off after 5 seconds.

POWER LED will blink one time.

Using the RESET function will erase all stored settings.



Do not use this unless necessary.



SLEEPNEO : 6

LEEP

PROLOGIC AUDIO ASSIGN

VOL

TUNER MEMORY SUBWOOFER MO/ST

TUNER MEMOR

SETUP/MENU

SETUP/MEN

RETURN

MUTE

ASC

FER

DSP

TUNING

TUNIN

/CH

POPUP

NFO

INFO

EXIT

ENG

● OPERATION

PUP

Using headphones

Use headphones (not supplied) for private listening pleasure.

Connect the headphones to the headphone (PHONES) jack and listen to music.

Do not turn the volume up too high when you use headphones as it may damage your hearing.



SOFTWARE UPGRADE

Samsung may offer upgrades for AV Receiver's ﬁ rmware in the future.

Please visit Samsung.com or contact the Samsung call center at 1-800-SAMSUNG (726-7864) to receive information about downloading upgrades and using a USB drive. Upgrades will be possible by connecting a USB drive to the USB port located on your AV Receiver.

Insert a USB drive containing the ﬁ rmware upgrade into the USB port



on the back of the main unit.

Please be careful to not disconnect the power or remove the USB



drive while upgrades are being applied. The main unit will turn off automatically after completing the ﬁ rmware upgrade. When software is upgraded, settings you have made will return to their default (factory) settings. We recommend you write down your settings so that you can easily reset them after the upgrade.

If you failed software upgrade, it is strongly recommended whole USB data



format to FAT16 and retry software upgrade.

The NTFS USB File System can not be supported.



Depending on the manufacturer, the USB may not be supported.



HW-C700-C770S-C770BS-XAA_0609.in53 53HW-C700-C770S-C770BS-XAA_0609.in53 53 2010-06-09  5:07:412010-06-09  5:07:41

Miscellaneous

OPERATING YOUR TV WITH THE REMOTE CONTROL

Press the POWER button to turn on the TV.

Press the AMP/TV button to set the remote to TV mode.

Point the remote control toward the TV.

While holding down the POWER button, enter the code corresponding to your brand of TV.

If there is more than one code listed for your TV in the table, enter one at a time to determine which code

•

works. If the code matches the TV's code, the TV will be turned off.

•

If TV is turned on or off when you press the POWER button of the remote control, the setting is completed.

You can use the TV POWER, VOLUME, CHANNEL, MENU and Numeric buttons (0~9).

•

The remote control may not work on some brands of TVs. Also, some operations may not be possible



depending on your brand of TV.

The remote control will work with Samsung TVs by default.



HW-C700-C770S-C770BS-XAA_0609.in54 54HW-C700-C770S-C770BS-XAA_0609.in54 54 2010-06-09  5:07:422010-06-09  5:07:42

OPERATING YOUR TV WITH THE REMOTE CONTROL (Continued)

TV Brand Code List

ENG

Brand Code Number Brand Code Number Brand Code Number

Admiral (M.Wards) 056, 057, 058 Luxman 018 Sylvania 018, 040, 048, 054, 059, A Mark 001, 015 LXI (Sears) 019, 054, 056, 059, 060,

Anam 001, 002, 003, 004,005,

006, 007, 008, 009, 010, 011, 012, 013, 014

AOC 001, 018, 040, 048 Marantz 040, 054 Teknika 003, 015, 018, 025 Bell & Howell (M.Wards) Brocsonic 059, 060 MGA 018, 040 Toshiba 019, 057, 063, 071, 101 Candle 018 Mitsubishi/MGA 018, 040, 054, 059, 060,

Citizen 003, 018, 025 MTC 018 Videch 059, 060, 069 CINEMA 097 NEC 018, 019, 020, 040, 059, Classic 003

Concerto 018 Nikei 003 Yamaha 018 Contec 046 Onking 003 York 040 Coronado 015 Onwa 003 Yupiteru 003 Craig 003, 005, 061, 082, 083,

Croslex 062 Penney 018 Dongyang 003, 054 Crown 003 Philco 003, 015, 017, 018, 048, CURTIS MATHES 059, 061, 063 FINLUX 054, 109, 114

CXC 003 Philips 015, 017, 018, 040, 048 Daewoo 002, 003, 004, 015,016,

Daytron 040 Radio Shack 017, 048, 056, 060, 061, Dynasty 003 BLAUPUNKT 108

Emerson 003, 015, 040, 046, 059,

Fisher 019, 065, 103 Sampo 040 MIVAR 113 Funai 003 Samsung 000, 015, 016, 017, 040, Futuretech 003 BANG&OLUFSEN 114 General Electric (GE) 006, 040, 056, 059, 066,

Hall Mark 040 METZ 114 Hitachi 015, 018, 050, 059, 069 Scott 003, 040, 060, 061 WEGA 114

Inkel 045 Sears 015, 018, 019 RADIOMARELLI 114 JC Penny 056, 059, 067, 086 Sharp 015, 057, 064, 101, 105, JVC 070 SINUDYNE 114

KTV 059, 061, 087, 088 Signature 2000

KEC 003, 015, 040 Sony 050, 051, 052, 053, 055, KMC 015

LG (Goldstar) 001, 015, 016, 017, 037,

057, 058, 081 Matsui 054 TMK 018, 040

084

017, 018, 019, 020, 021, 022, 023, 024, 025, 026, 027, 028, 029, 030, 032, 034, 035, 036, 040, 048, 059, 090, 099, 100

061, 064, 082, 083, 084, 085

067, 068

038, 039, 040, 041, 042, 043, 044, 054, 086

Magnavox 015, 017, 018, 048, 054,

Panasonic 006, 007, 008, 009, 054,

Pioneer 063, 066, 080, 091 RADIOLA 054, 112 Portland 015, 018, 059 SCHNEIDER 054 Proton 040 AKAI 103 QUASAR 006, 066, 067 GRUNDIG 108, 109, 113, 119, 120,

RCA/Proscan 018, 059, 067, 076, 077,

Realistic 003, 019 IMPERIAL 113

Sanyo 019, 061, 065, 101, 102,

(M.Wards)

Soundesign 003, 040 Spectricon 001 SSS 018

062, 063, 065, 071

059, 060, 062, 072, 089

075, 101Cetronic 003 Vidtech 018

060

066, 067, 073, 074

054, 059, 062, 069, 090

054, 062, 072, 112, 114, 117, 118

075

078, 092, 093, 094

043, 046, 047, 048, 049, 054, 059, 060, 098

103, 104

106, 115 057, 058 TELEFUNKEN 116

101

Symphonic 061, 095, 096 Tatung 006

Techwood 018

Wards 015, 017, 018, 040, 048,

Zenith 058, 079 Zonda 001

LOWE 054

YOKO 054 LOEWE OPTA 054, 114 PHONOLA 054, 112, 114

SIEMENS 108 CGE 113

SABA 114

BRIONVEGA 114

FORMENTI 114

SINGER 114

060, 062

107, 109, 110, 111, 113

054, 060, 064

121

● MISCELLANEOUS

HW-C700-C770S-C770BS-XAA_0609.in55 55HW-C700-C770S-C770BS-XAA_0609.in55 55 2010-06-09  5:07:422010-06-09  5:07:42

Miscellaneous

OPERATING YOUR DVD OR BD PLAYER WITH THE REMOTE CONTROL

Press the POWER button to turn on the DVD (BD) player.

Press the BD/DVD button on the remote control to set the remote to DVD (BD) mode.

Point the remote control toward the DVD (BD).

While holding down POWER button, enter the code corresponding to your brand of DVD (BD).

If there is more than one code listed for your DVD (BD) in the table, enter one at a time to determine which

•

code works. If the code matches the DVD (BD)'s code, the DVD (BD) will be turned off.

•

If DVD (BD) is turned on or off when you press the POWER button of the remote controller, the setting is

completed.

You can use DVD (BD) POWER, PLAY, PAUSE, STOP, SKIP, MENU and Numeric buttons (0~9).

•

The remote control may not work on some brands of DVD.



Also, some operations may not be possible depending on your brand of DVD.

The remote control will work with Samsung DVD (BD) by default.



DVD Brand Code List

Brand Code Number Brand Code Number Brand Code Number

DENON 003, 032 ONKYO 004, 014 TOSHIBA 004, 018 DOONOON 019 OPTIMUS 011 YAMAHA 009, 033 DMTECH 017 PANASONIC 021 ZENITH 004, 024 FISHER 002 PROSCAN 006 TAEGWANG 026 GE 006 PHILIPS 004, 023 PS2 028 HARMAN/KARDON 012 PIONEER 007, 011, 022, 025 X-BOX 029 JVC 010, 013 RCA 006 APEX 030 KENWOOD 008 SAMSUNG 000, 027 Marantz 031 LG 001 SANYO 002 MAGNAVOX 004 SONY 015, 020 MITSUBISHI 005, 016 THETA DIGITAL 011

BD player Brand Code List

Brand Code Number

SAMSUNG 000, 001, 002, 003, 004

The remote control will control Samsung BD players only.



HW-C700-C770S-C770BS-XAA_0609.in56 56HW-C700-C770S-C770BS-XAA_0609.in56 56 2010-06-09  5:07:432010-06-09  5:07:43

Troubleshooting

Before requesting service, please check the following.

Symptom Check Remedy

The unit will not turn on.

A function does not work when the button is pressed.

Sound is not produced.

Picture does not appear on a TV when the function is selected.

Remote controller does not work.

The sound from the left/right channels is reversed.

Can't receive radio broadcasts.

There is no sound from surround speakers.

There is no sound from surround back speakers

Can't select EX/ES mode.

• Is the power cord plugged into the outlet?

• Is there static electricity in the air? • Disconnect the power plug and

• Are the speakers and external components connected properly?

• Is the Mute function on?

• Is the volume set to minimum?

• Is the Speaker Size set incorrectly to NONE?

• Is the external component connected properly?

• Are the batteries drained?

• Is the distance between remote control and main unit too great?

• Are the left/right speaker or left/right input/output cables connected properly?

• Is FM antenna connected properly? • Connect the antenna correctly.

• Are the surround speakers connected properly?

• Is SURR (surround) incorrectly set to NONE in the Speaker Size?

• Is surround mode set to stereo?

• Are the surround back speakers

connected properly?

• Is SBACK (Surround Back) set to

NONE in the Speaker Size?

• Is Surround Mode set to EX/ES?

• Is SBACK (Surround Back) set to

NONE in the Speaker Size?

• Is the input signal selected properly?

ENG

● TROUBLESHOOTING

• Connect the power plug to the outlet.

connect it again.

• Connect them correctly.

• Press the MUTE button to cancel the

function.

• Adjust the volume.

• Refer to pages 36 to select LARGE, SMALL or YES.

• Connect it correctly.

• Replace with new batteries.

• Operate at close distance.

• Check the left/right channel and connect it/them correctly.

• If the input strength of antenna signal is weak, install the FM antenna in a place with good reception.

• Refer to pages 16 ~18 to connect them properly.

• Refer to page 36 to select LARGE or SMALL.

• Refer to pages 47~48 to select proper Surround Mode.

• Refer to pages 16 ~18 to connect

them properly.

• Refer to page 36 to select LARGE

or SMALL.

• Refer to page 43 to set Surround

Mode to EX/ES.

• Refer to page 36 to select LARGE or

SMALL.

• Use a 7.1 channel external

component.

HW-C700-C770S-C770BS-XAA_0609.in57 57HW-C700-C770S-C770BS-XAA_0609.in57 57 2010-06-09  5:07:432010-06-09  5:07:43

Troubleshooting

Symptom Check Remedy

Can't select Dolby Pro Logic llx mode.

Can't select NEO:6 mode.

There is no sound when playing a DTS encoded DVD.

• Is the input signal selected properly? • Only 2 channel signal can select Dolby Pro Logic IIx mode. (ex:Dolby Digital, PCM, 2 channel analog input signal.)

• Is the input signal selected properly? • Use PCM and Analog input signal.

• Is Digital input selected? • Check whether the DVD player is

properly connected and refer to page 31 to select the digital input.

Product protection function

Heat protection

•

The protection function will come on if the main unit or power transformer overheats.

" " will appear in the display .

This function will come on :

- If speaker terminal is shorted

- If speaker cable is shorted If there is no problem when you turn the unit on again after turning it off, PROTECTION mark will disappear on the display and the unit will work properly.



If PROTECTION appears on the display, check whether the speaker terminal is shorted and then turn on the unit again.

ASC Error List

Error No. VFD Message Action

E01

E02

E03

E04

E05

E07

E08

E13

E14

HP CONCT

NO MIC

NOISY

MIC LEVL

NO FRONT

LEVL OVR

DIST OVR

TIME OVR

CODE ERR

Disconnect the headphones.

Connect the microphone.

Take an appropriate action to reduce the surrounding noise.

The speaker is too close to the microphone. Check the distance between speaker and microphone.

Check if the front speaker is connected properly.

Check the position of each of speaker and microphone.

The distance between speaker and microphone exceeds the acceptable value. Check the location of microphone and each speaker.

Unplug the power cable and plug it back. Then, perform ASC again.

HW-C700-C770S-C770BS-XAA_0616.in58 58HW-C700-C770S-C770BS-XAA_0616.in58 58 2010-06-16  4:17:532010-06-16  4:17:53

Appendix

SPECIFICATIONS

Power supply 120V, 60 Hz

Standby power consumption 0.9W

Power consumption

GENERAL

FM TUNER

AMPLIFIER

FREQUENCY

RESPONSE

HDMI

VIDEO OUTPUT

Weight 13.7 Ibs

Dimensions (W x H x D) 17.2 x 6.6 x 14.7 inches

Operating temperature range 41°F~+95°F

Operating humidity range 10%~75%

Frequency response 87.5~108.0MHz

Usable sensitivity 12dBf

S/N ratio MONO/STEREO 55/55dB

Distortion MONO/STEREO 0.3/0.8%

Stereo separation 30dB

Tuner output level 1kHz, 75kHz Dev

Rated output 20Hz~20kHz/THD = 0.9%

Front speaker (left+right) 6 Ω 120W/CH

Center speaker 6 Ω 120W/CH

Surround speaker (left+right) 6 Ω 120W/CH

Surround back speaker (left+right) 6 Ω 120W/CH

Subwoofer speaker 8 Ω 150W/CH

Input sensitivity/impedance 450mV/47kΩ

S/N ratio (analog input) 80dB

Separation (1kHz) 60dB

Analog input 20Hz~20kHz(±3dB)

Digital input/96kHz PCM 20Hz ~44kHz(±3dB)

Input Compatible 1080p

Output Compatible 1080p

TV format NTSC/PAL

Input level/impedance 1Vp-p/75 Ω

Output level/impedance 1Vp-p/75 Ω

Video frequency response 5Hz to 10kHz(-3dB)

S/N Ratio 60dB

ENG

● APPENDIX

Main unit 75W

Subwoofer 35W

* S/N Ratio, Distortion, Separation and Usable sensitivity are based on measurement using AES (Audio Engineering

Society) guidelines.

- Samsung Electronics Co., Ltd reserves the right to change the speciﬁ cations without notice.

- Weight and dimensions are approximate.

- Design and speciﬁ cations are subject to change without prior notice.

HW-C700-C770S-C770BS-XAA_0609.in59 59HW-C700-C770S-C770BS-XAA_0609.in59 59 2010-06-09  5:07:432010-06-09  5:07:43

SAMSUNG AV receiver

LIMITED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) Year Parts and Labor*

(*90 days Parts and Labor for Commercial Use)

This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG's authorized service center. Transportation of the product to and from the service center is the responsibility of the purchaser.

SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer.

SAMSUNG's obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name are set forth in the applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided, are on an “AS IS” basis. Non-SAMSUNG manufacturers, suppliers, publishers, and service providers may provide their own warranties.

This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the extent otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply to the following, including, but not limited to: damage which occurs in shipment; delivery and installation; applications and uses for which this product was not intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning or other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied and authorized by SAMSUNG, or which damage this product or result in service problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions, cleaning, maintenance and environmental instructions that are covered and prescribed in the instruction book; product removal or reinstallation; reception problems and distortion related to noise, echo, interference or other signal transmission and delivery problems. SAMSUNG does not warrant uninterrupted or error-free operation of the product.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND PURCHASER°ØS PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

To obtain warranty hardware service, please contact SAMSUNG at:

Samsung Electronics America, Inc.

105 Challenger Road Ridgefield Park, NJ07660-0511

1-800-SAMSUNG(726-7864) and www.samsung.com

HW-C700-C770S-C770BS-XAA_0609.in60 60HW-C700-C770S-C770BS-XAA_0609.in60 60 2010-06-09  5:07:432010-06-09  5:07:43

Contact SAMSUNG WORLD WIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.

Area Contact Center

North America



Web Site

Canada 1-800-SAMSUNG (726-7864) www.samsung.com

Mexico

01-800-SAMSUNG (726-7864)

www.samsung.com

U.S.A 1-800-SAMSUNG (726-7864) www.samsung.com

Latin America

Argentine 0800-333-3733 www.samsung.com

Brazil

0800-124-421 4004-0000

www.samsung.com

Chile 800-SAMSUNG (726-7864) www.samsung.com

Nicaragua 00-1800-5077267 www.samsung.com

Honduras 800-7919267 www.samsung.com

Costa Rica 0-800-507-7267 www.samsung.com

Ecuador 1-800-10-7267 www.samsung.com

El Salvador 800-6225 www.samsung.com

Guatemala 1-800-299-0013 www.samsung.com

Jamaica 1-800-234-7267 www.samsung.com

Panama 800-7267 www.samsung.com

Puerto Rico 1-800-682-3180 www.samsung.com

Rep. Dominica 1-800-751-2676 www.samsung.com

Trinidad & Tobago

1-800-SAMSUNG (726-7864) www.samsung.com

Venezuela 0-800-100-5303 www.samsung.com

Colombia 01-8000112112 www.samsung.com

Europe

Austria

Belgium 02-201-24-18

Czech

0810 - SAMSUNG (7267864, € 0.07/min)

800 - SAMSUNG (800-726786)

www.samsung.com

www.samsung.com/ be (Dutch) www.samsung.com/ be_fr (French)

www.samsung.com

Denmark 70 70 19 70 www.samsung.com

Finland 030 - 6227 515 www.samsung.com

France 01 48 63 00 00 www.samsung.com

Germany

01805 - SAMSUNG (726-7864 € 0,14/Min)

www.samsung.com

Hungary 06-80-SAMSUNG (726-7864) www.samsung.com

Italia 800-SAMSUNG (726-7864) www.samsung.com

Luxemburg 261 03 710 www.samsung.com

Netherlands

0900-SAMSUNG (0900-7267864) (€ 0,10/Min)

www.samsung.com

Norway 815-56 480 www.samsung.com

Poland

Portugal

0 801 1SAMSUNG (172678) 022-607-93-33

80820-SAMSUNG (726-7864)

www.samsung.com

Slovakia 0800-SAMSUNG (726-7864) www.samsung.com

Spain

902 - 1 - SAMSUNG (902 172 678)

www.samsung.com

Sweden 0771 726 7864 (SAMSUNG) www.samsung.com

U.K 0845 SAMSUNG (7267864) www.samsung.com

Eire 0818 717100 www.samsung.com

Area Contact Center

Switzerland

0848 - SAMSUNG (7267864, CHF 0.08/min)



Web Site

www.samsung.com/ch www.samsung.com/ ch_fr/ (French)

Lithuania 8-800-77777 www.samsung.com

Latvia 8000-7267 www.samsung.com

Estonia 800-7267 www.samsung.com

CIS

Russia 8-800-555-55-55 www.samsung.com

Georgia 8-800-555-555

Armenia 0-800-05-555

Azerbaijan 088-55-55-555

Kazakhstan 8-10-800-500-55-500

Uzbekistan 8-10-800-500-55-500 www.samsung.com

Kyrgyzstan 00-800-500-55-500 www.samsung.com

Tadjikistan 8-10-800-500-55-500 www.samsung.com

Ukraine 0-800-502-000

www.samsung.ua www.samsung.com/ ua_ru

Belarus 810-800-500-55-500

Moldova 00-800-500-55-500

Asia Paciﬁ c

Australia 1300 362 603 www.samsung.com

New Zealand

China

Hong Kong (852) 3698-4698

India

Indonesia

0800 SAMSUNG (0800 726 786)

400-810-5858 010-6475 1880

3030 8282 1800 110011 1800 3000 8282 1800 266 8282

0800-112-8888 021-5699-7777

www.samsung.com

www.samsung.com/ hk www.samsung.com/ hk_en/

www.samsung.com

Japan 0120-327-527 www.samsung.com

Malaysia 1800-88-9999 www.samsung.com

1-800-10-SAMSUNG (726-7864)

Philippines

1-800-3-SAMSUNG (726-7864) 1-800-8-SAMSUNG (726-7864) 02-5805777

www.samsung.com

Singapore 1800-SAMSUNG (726-7864) www.samsung.com

Thailand

1800-29-3232 02-689-3232

www.samsung.com

Taiwan 0800-329-999 www.samsung.com

Vietnam 1 800 588 889 www.samsung.com

Middle East & Africa

Turkey 444 77 11 www.samsung.com

South Africa 0860-SAMSUNG (726-7864) www.samsung.com

U.A.E 800-SAMSUNG (726-7864) www.samsung.com

Bahrain 8000-4726

Jordan 800-22273

HW-C700-C770S-C770BS-XAA_0609.in61 61HW-C700-C770S-C770BS-XAA_0609.in61 61 2010-06-09  5:07:432010-06-09  5:07:43

QUESTIONS OR COMMENTS?

COUNTRY CALL OR VISIT US ONLINE AT WRITE

IN THE US

HW-C700-C770S-C770BS-XAA_0609.in62 62HW-C700-C770S-C770BS-XAA_0609.in62 62 2010-06-09  5:07:432010-06-09  5:07:43

1-800-SAMSUNG

(7267864)

www.samsung.com/us

Samsung Electronics America, Inc.

105 Challenger Road Ridgeﬁ eld Park,

NJ 07660-0511

Code No. AH68-02260R

Samsung HW-C700B-XAA User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual