SAMSUNG HT-E5350 User Manual

HT-E5350

5.1CH Blu-ray™

Home Entertainment System

user manual

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service,

please register your product at

www.samsung.com/register

HT-E5350_ZC_ENG_0316.indd 1

2012-03-16 3:30:23

Safety Information

Warning

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

		CAUTION
		RISK OF ELECTRIC SHOCK
		DO NOT OPEN
The lighting flash and Arrowhead	CAUTION: TO REDUCE THE RISK OF			The explanation point within the
within the triangle is a warning sign	ELECTRIC SHOCK, DO NOT REMOVE COVER			triangle is a warning sign alerting you
alerting you of dangerous voltage	(OR BACK) NO USER SERVICEABLE PARTS			of important instructions accompanying
inside the product.	INSIDE. REFER SERVICING TO QUALIFIED			the product.
	SERVICE PERSONNEL.

WARNING

•To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

Note to CATV system installer

This reminder is provided to call the CATV system installer’s attention to Section 820~40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

CLASS 1 LASER PRODUCT

This product is classified as a CLASS 1 LASER product.

Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

DANGER :

•VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM. (FDA 21 CFR)

CAUTION :

•CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO THE BEAM (IEC 60825-1)

•THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVER AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CLASS 1	LASER PRODUCT
KLASSE 1	LASER PRODUKT
LUOKAN 1	LASER LAITE
KLASS 1	LASER APPARAT
PRODUCTO	LÁSER CLASE 1

| 2 English

HT-E5350_ZC_ENG_0316.indd 2

2012-03-16 3:30:27

Precautions

Important Safety Instructions

Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below.

Keep these operating instructions handy for future reference.

1 . Read these instructions.

2 . Keep these instructions.

3 . Heed all warnings.

4 . Follow all instructions.

5 . Do not use this apparatus near water.

6 . Clean only with a dry cloth.

7 . Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8 . Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including AV receivers) that produce heat.

9 . Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 . Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where it exits the apparatus.

11 . Only use attachments/accessories specified by the manufacturer.

12 . Use only with the cart,

stand, tripod, bracket, or table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury from tip-over.

13 . Unplug this apparatus during lightning storms or when unused for long periods of time.

14 . Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Disc Storage & Management

• Holding Discs

- Fingerprints or scratches on a disc may reduce sound and

picture quality or cause skipping.

-Avoid touching the surface of a disc where data has been recorded.

-Hold the disc by the edges so that fingerprints will not get on the surface.

-Do not stick paper or tape on the disc.

•Cleaning Discs

- If you get fingerprints or dirt on a disc, clean it with a mild detergent diluted in water and wipe with a soft cloth.

-When cleaning, wipe gently from the inside to the outside of the disc.

-Disc Storage

Do not keep in direct sunlight.

Keep in a cool ventilated area.

Keep in a clean protection jacket and store vertically.

Handling Cautions

•Do not expose this apparatus to dripping or splashing. Do not put objects filled with liquids, such as vases, on the apparatus.

•To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the power plug must be easily and readily accessible at all times.

•Do not touch the power plug with a wet hand. It can cause an electric shock.

English 3 |

Information Safety 01

HT-E5350_ZC_ENG_0316.indd 3

2012-03-16 3:30:28

Safety Information

•Do not plug multiple electric devices into the same wall socket. Ovedrloading a socket can cause it to overheat, resulting in a fire.

•Maintenance of the Cabinet

-Before connecting other components to this product, be sure to turn them off.

-If you move your product suddenly from a cold place to a warm place, condensation may occur on the operating parts and lens and cause abnormal disc playback. If this occurs, unplug the product, wait for two hours, and then connect the plug to the power outlet. Then, insert the disc, and try to play back again.

•If the product makes an abnormal noise or produces a burning smell or smoke, turn off the power switch immediately and disconnect the power plug from the wall outlet. Then, contact the nearest customer service center for technical assistance. Do not use the product. Using the product as it is may cause a fire or an electric shock.

•To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the power plug must be easily and readily accessible at all times.

Using the 3D Function

IMPORTANT HEALTH AND SAFETY INFORMATION FOR 3D PICTURES. Read and understand the following safety information before using the 3D function.

•Some viewers may experience discomfort while viewing 3D TV such as dizziness, nausea, and headaches.

If you experience any such symptom, stop viewing 3D TV, remove the 3D Active Glasses, and rest.

•Watching 3D images for an extended period of time may cause eye strain. If you feel eye strain, stop viewing 3D TV, remove your 3D Active Glasses, and rest.

•A responsible adult should frequently check on children who are using the 3D function.

If there are any reports of tired eyes, headaches, dizziness, or nausea, have the child stop viewing 3D TV and rest.

| 4 English

•Do not use the 3D Active Glasses for other purposes (such as general eyeglasses, sunglasses, protective goggles, etc.)

•Do not use the 3D function or 3D Active Glasses while walking or moving around. Using the 3D function or 3D Active Glasses while moving around may cause you to bump into objects, trip, and/or fall, and cause serious injury.

•If you want to enjoy 3D content, connect a 3D device (3D compliant AV receiver or TV) to the product’s HDMI OUT port using a high-speed HDMI cable. Put on 3D glasses before playing the 3D content.

•The product outputs 3D signals only through HDMI cable connected to the HDMI OUT port.

•As the video resolution in 3D play mode is fixed according to the resolution of the original 3D video, you can not change the resolution to your preference.

•Some functions such as BD Wise, screen size adjustment, and resolution adjustment may not operate properly in 3D play mode.

•You must use a high-speed HDMI cable for proper output of the 3D signal.

•Stay at least three times the width of the screen from the TV when watching 3D images. For example, if you have a 46 inch screen, stay 138 inches (11.5 feet) from the screen.

-Place the 3D video screen at eye level for the best 3D picture.

•When the product is connected to some 3D devices, the 3D effect may not function properly.

•This product does not convert 2D content into 3D.

•“Blu-ray 3D” and “Blu-ray 3D” logo are trademarks of the Blu-ray Disc Association.

Copyright

© 2012 Samsung Electronics Co.,Ltd.

All rights reserved; No part or whole of this user’s manual may be reproduced or copied without the prior written permission of Samsung Electronics Co.,Ltd.

HT-E5350_ZC_ENG_0316.indd 4

2012-03-16 3:30:29

License

•Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.

•Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,392,195; 7,272,567; 7,333,929; 7,212,872 & other U.S. and worldwide patents issued & pending. DTS-HD, the Symbol, & DTSHD and the Symbol together are registered trademarks & DTS-HD Master Audio | Essential is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.

•The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

•Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners.

•This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of

Rovi Corporation. Reverse engineering and disassembly are prohibited.

•Blu-ray Disc™, Blu-ray™, and the logos are trademarks of Blu-ray Disc Association.

•iPad, iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

•This product uses Cinavia technology to limit the use of unauthorized copies of some commercially-produced film and videos and

their soundtracks. When a prohibited use of an unauthorized copy is detected, a message will be displayed and playback or copying will be interrupted.

More information about Cinavia technology is provided at the Cinavia Online Consumer

Information Center at http://www.cinavia.com. To request additional information about Cinavia by mail, send a postcard with your mailing address to: Cinavia Consumer Information Center, P.O. Box 86851, San Diego, CA, 92138, USA.”

This product incorporates proprietary technology under license from Verance Corporation and is protected by U.S. Patent 7,369,677 and other U.S. and worldwide patents issued and pending as well as copyright and trade secret protection for certain aspects of such technology. Cinavia is a trademark of Verance Corporation. Copyright 2004-2010 Verance Corporation. All rights reserved by Verance. Reverse engineering or disassembly is prohibited.

•Open Source License Notice

-In the case of using open source software, Open Source Licenses are available on the product menu.

English 5 |

Information Safety 01

HT-E5350_ZC_ENG_0316.indd 5

2012-03-16 3:30:29

Contents

SAFETY INFORMATION

2Warning

3Precautions

3Disc Storage & Management

3Handling Cautions

4Using the 3D Function

4Copyright

5License

GETTING STARTED

7Disk and Format Compatibility

8 Logos of Discs the product can play

11Accessories

12Front Panel

12Rear Panel

13Remote Control

CONNECTIONS

15Attaching the Toroidal Ferrite Core to the Power Cord of the Main Unit

15Connecting the Speakers

16Speaker Components

16Installing the Speakers on the Tallboy Stand

17Connecting The Speakers

18Connecting the Optional Wireless Receiver Module

19Connecting the FM Antenna

20Connecting to an iPod/iPhone

20Using a USB Cable

20Using a Dock

21Connecting to a TV

21Method 1 Connecting to a TV with an HDMI Cable - Best Quality (Recommended)

21Method 2 Connecting to a TV with a Video Cable - Good Quality

22Connecting to External Devices

22Method 1 HDMI IN : Connecting to an External Component with an HDMI Cable

22Method 2 OPTICAL : Connecting an External Digital Audio Component

22Method 3 AUX IN : Connecting an External Analog Component

| 6 English

23 Connecting to a Network Router

23 Wired Network

23 Wireless Network

SETTINGS

24 The Initial Settings Procedure

26 The Home Screen

26Accessing the Settings Screen

27Settings Menu Functions

32 Networks and the Internet

36 Upgrading Software

MEDIA PLAY

38The AllShare Play Screen

39Playing Files on a USB Storage Device or iPod/iPhone

39iPod/iPhone Models You Can Use with This Product

40The Function Screen

40Playing Commercial Video Discs

40Playing Commercial Audio Discs

41Playing a Disc with User Recorded Content

41 Using the AllShare Network Function

43 Controlling Video Playback

45Controlling Music Playback

46Playing Photo Contents

47Using the Tools Menu when a File is Highlighted

49 Listening to Radio

49Using the Special Effects Remote Control Buttons

NETWORK SERVICES

51 Using Smart Hub

53 BD-LIVE™

APPENDIX

54 Additional Information

60 Troubleshooting

63 Specifications

HT-E5350_ZC_ENG_0316.indd 6

2012-03-16 3:30:30

Getting Started

Disk and Format Compatibility

Disc types and contents your product can play

	Media	Disc Type	Details
		Blu-ray Disc	BD-ROM or BD-RE/-R disc recorded in the BD-RE format.
		3D Blu-ray Disc
	VIDEO
		DVD-VIDEO, DVD-RW,	DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVDR/+R discs that have
		DVD-R, DVD+RW,	been recorded and finalized, or a USB storage media containing MKV, MP4
		DVD+R	contents.
	MUSIC	CD-RW/-R, DVD-RW/-R,	Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R discs or a USB storage
		BD-RE/-R	media containing MP3 or WMA contents.
	PHOTO	CD-RW/-R, DVD-RW/-R,	Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R discs or a USB storage
		BD-RE/-R	media containing JPEG contents.

|NOTE |

The product may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions.

If a DVD-RW/-R disc has not been recorded properly in DVD video format, it will not be playable.

Your product will not play content that has been recorded on a DVD-R at a bitrate that exceeds 10 Mbps.

Your product will not play content that has been recorded on a BD-R or USB device at a bitrate that exceeds 30 Mbps.

Playback may not work for some types of discs, or when you use specific operations, such as angle change and aspect ratio adjustment. Information about the discs is written in detail on the disc box. Please refer to this if necessary.

When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.

Disc types your product cannot play

• HD DVD	• DVD-RAM	• DVD-RW(VR mode)	• 3.9 GB DVD-R Disc
• DVD-ROM/PD/MV-	• Super Audio CD	• CVD/CD-ROM/CDV/	for Authoring.
Disc, etc	(except CD layer)	CD-G/CD-I/LD
		(CD-Gs play audio
		only, not graphics.)

|NOTE |

This product may not respond to all operating commands because some Blu-ray Disc, DVD, and CD discs allow specific or limited operation and provide only certain features during playback.

Please note that this is not a defect in the product.

Samsung cannot guarantee that this product will play every disc bearing the Blu-ray Disc, DVD or CD logo because disc formats evolve, and problems and errors may occur during the creation of Blu-ray Disc, DVD, and CD software and/or the manufacture of discs.

Please contact the SAMSUNG Customer Care Center at 1-800-726-7864 if you have questions or encounter difficulty when playing Blu-ray Disc, DVD, or CD discs in this product. Also, refer to rest of this user manual for additional information on playback restrictions.

Some commercial discs and DVD discs purchased outside your region may not play on this product.

English 7 |

Started Getting 02

HT-E5350_ZC_ENG_0316.indd 7

2012-03-16 3:30:32

Getting Started

Region Code

Both products and discs are coded by region. These regional codes must match for a disc to play. If the codes do not match, the disc will not play.

The Region Number for this product is displayed on the rear panel of the product.

Disc Type	Region				Area
		Code
			A		North America, Central America,
					South America, Korea, Japan,
					Taiwan, Hong Kong and South
					East Asia.
Blu-ray Disc			B		Europe, Greenland, French
					territories, Middle East, Africa,
					Australia and New Zealand.
			C		India, China, Russia, Central and
					South Asia.
					The U.S., U.S. territories and
			1
					Canada
					Europe, Japan, the Middle East,
			2
					Egypt, South Africa, Greenland
					Taiwan, Korea, the Philippines,
			3
					Indonesia, Hong Kong

DVD-VIDEO

Mexico, South America,

Central America, Australia,

4 New Zealand, Pacific Islands,

Caribbean

Russia, Eastern Europe, India, 5 most of Africa, North Korea,

Mongolia

6 China

|NOTE |

If the Region number of a Blu-ray Disc/DVDs does not correspond to the Region number of this product, the product cannot play the disc.

| 8 English

Logos of Discs the product can play

Blu-ray Disc

3D Blu-ray Disc

BD-LIVE			Dolby

DTS

NTSC broadcast system in

U.S.A, Canada, Korea, Japan

Java

Supported Formats

Music File Support

File	Container	Audio	Support Range
Extension		Codec
*.mp3	MP3	MP3	-
			Compliant with
			WMA version 10
			* Sampling rates (in
*.wma	WMA	WMA	kHz) - 8, 11, 16,
			22, 32, 44.1, 48
			* Bitrates - All
			bitrates in the
			range 5kbps to
			384kbps

HT-E5350_ZC_ENG_0316.indd 8

2012-03-16 3:30:33

Video File Support

	File Extension	Container	Video Codec	Resolution	Frame rate	Bitrate	Audio Codec
					(fps)	(Mbps)
			H.264 BP/MP/HP	1920x1080	6 ~ 30	25	MP3
	*.avi	AVI					AC3
			MPEG4 SP/ASP	1920x1080	6 ~ 30	8	LPCM
							DTS Core
			H.264 BP/MP/HP	1920x1080	6 ~ 30	25	MP3
	*.mkv	MKV					AC3
			MPEG4 SP/ASP	1920x1080	6 ~ 30	8	LPCM
							DTS Core
			H.264 BP/MP/HP	1920x1080	6 ~ 30	25	MP3
	*.asf	ASF					AC3
			MPEG4 SP/ASP	1920x1080	6 ~ 30	8	LPCM
							WMA
	*.wmv	WMV (wmv9)	Window Media	1920x1080	6 ~ 30	25	WMA
			Video v9
	*.mp4	MP4	H.264 BP/MP/HP	1920x1080	6 ~ 30	25	MP3
			MPEG4 SP/ASP	1920x1080	6 ~ 30	8	AAC
	*.3gp	3GPP	H.264 BP/MP/HP	1920x1080	6 ~ 30	25	AAC
			MPEG4 SP/ASP	1920x1080	6 ~ 30	8
		VRO	MPEG2	1920x1080	24/25/30	25	AC3
	*.vro						MPEG
			MPEG1	1920x1080	24/25/30	25
		VOB					LPCM
			MPEG1	1920x1080	24/25/30	25	AC3
	*.mpg	PS	MPEG2	1920x1080	24/25/30	25	MPEG
	*.mpeg						LPCM
			H.264	1920x1080	6 ~ 30	25	AAC
	*.ts		MPEG2	1920x1080	24/25/30	25	AC3
							AAC
	*.tp	TS	H.264	1920x1080	6 ~ 30	25
							MP3
	*.trp						DD+
			VC1	1920x1080	6 ~ 30	25

Limitations

-Even when a file is encoded by a supported codec listed above, the file might not be played if its content has a problem.

-Normal playback is not guaranteed if the file’s container information is wrong or the file itself is corrupted.

-Files having higher bit or frame rates than standard may stutter when played back.

English 9 |

Started Getting 02

HT-E5350_ZC_ENG_0316.indd 9

2012-03-16 3:30:35

Getting Started

-The Seek (skip) function is not available if the file’s index table is damaged.

-When you playback a file remotely through a network connection, video playback may stutter depending on the network speed.

Video decoder

-Supports up to H.264 Level 4.1

-Does not support H.264 FMO/ASO/RS, VC1 SP/MP/AP L4 and AVCHD

-MPEG4 SP, ASP :

Below 1280 x 720 : 60 frames max Above 1280 x 720 : 30 frames max

-Does not support GMC 2 or higher

Audio decoder

-Supports WMA 7, 8, 9 and STD

-Does not support WMA 9 PRO multi-channel files if the number of channels is more than 2 or the files require lossless audio decoding.

-Does not support WMA sampling rate of 22050Hz mono

Notes on the USB connection

•Your product supports USB storage media, MP3 players, digital cameras, and USB card readers.

•The product does not support folder or file names longer than 128 characters.

•Some USB/digital camera devices may not be compatible with the product.

•Your product supports the FAT 16, FAT 32, and NTFS files systems.

•Connect USB devices directly to the product’s USB port. Connecting through a USB cable may cause compatibility problems.

•Inserting more than one memory device into a multi-card reader may cause the reader to operate improperly.

•The product does not support the PTP protocol.

•Do not disconnect a USB device during a “loading” process.

•The bigger the image resolution, the longer the image takes to display.

| 10 English

•This product cannot play MP3 files with DRM (Digital Rights Management) downloaded from commercial sites.

•Your product only supports video that is under 30fps (frame rate).

•Your product only supports USB Mass Storage Class (MSC) devices such as thumb drives and USB HDD. (HUB is not supported.)

•Certain USB HDD Devices, multi-card readers and thumb drives may not be compatible with this product.

•If some USB devices require excessive power, they may be limited by the circuit safety device.

•If playback from a USB HDD is unstable, provide additional power by plugging the HDD into a wall socket. If the problem continues, contact the USB HDD manufacturer.

•You must remove the USB storage device safely (by performing the “Safely Remove USB” function) to prevent possible damage to the USB memory.

Press the HOME button to move to the home menu, press the YELLOW (C) button, and then press the E button.

•SAMSUNG is not responsible for any data file damage or data loss.

AVCHD

(Advanced Video Codec High Definition)

•This product can play back AVCHD format discs. These discs are normally recorded and used in camcorders.

•The AVCHD format is a high definition digital video camera format.

•The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the conventional image compressing format.

•Some AVCHD discs use the “x.v.Color” format. This product can play back AVCHD discs that use “x.v.Color” format.

•“x.v.Color” is a trademark of Sony Corporation.

•“AVCHD” and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd. and Sony Corporation.

HT-E5350_ZC_ENG_0316.indd 10

2012-03-16 3:30:36

|NOTE |

Some AVCHD format discs may not play, depending on the recording conditions.

AVCHD format discs need to be finalized.

“x.v.Color” offers a wider color range than normal DVD camcorder discs.

Some MKV and MP4 format discs may not play, depending on their video resolution and frame rate.

Accessories

Check for the supplied accessories below.

						FUNCTION
						TV
						SOURCE
				RECEIVER		SLEEP
				BD	TV
				1	2	3
				4	5	6
				7	8	9
				DISC MENU		TITLE MENU
					0	POPUP
					MUTE
	Video Cable	FM Antenna	iPod Dock	VOL	S/W LEVEL	TUNING
						/ CH
				HOME		REPEAT
					TUNER
					MEMORY MO/ST
				A	B C	D
				SMART	SEARCH '	' 3DSOUND
				HUB
				vTuner	AUDIO SUBTITLE SOUND
						EFFECT
			(For Power cord)
	User Manual	Toroidal Ferrite Core		Remote Control /
				Batteries (AAA size)

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.

An administration fee may be charged if either

a.an engineer is called out at your request and there is no defect in the product (i.e. where you have failed to read this user manual)

b.you bring the unit to a repair center and there is no defect in the product (i.e. where you have failed to read this user manual).

The amount of such administration charge will be advised to you before any work or home visit is carried out.

Started Getting 02

English 11 |

HT-E5350_ZC_ENG_0316.indd 11

2012-03-16 3:30:36

Getting Started

Front Panel

PLAY/PAUSE			ENTER
STOP		OPEN/CLOSE
FUNCTION				VOLUME CONTROL

			5V 500mA
DISC TRAY	DISPLAY	USB HOST	POWER

REMOTE CONTROL

SENSOR

|NOTE |

To upgrade the product's software through the USB Host jack, you must use a USB memory stick.

When the product displays the Blu-ray Disc menu, you cannot start the movie by pressing the 6 button on the product or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and then press the E button.

Rear Panel

FM ANTENNA

COOLING FAN

iPod	AUX IN	VIDEO OUT
SPEAKERS OUT		AUX	VIDEO
		IN	OUT

	: 3
SURROUND	IMPEDANCE
SURROUND	OPTICAL

iPod	LAN	WIRELESS	HDMI OUT	1	HDMI IN	2	DIGITAL	FM ANT
							AUDIO IN

SPEAKER OUTPUT LAN TERMINAL			HDMI OUT		HDMI IN
CONNECTORS
		TX CARD CONNECTION
						EXTERNAL DIGITAL
		(WIRELESS)				AUDIO IN (OPTICAL)

|NOTE |

Ensure a minimum of 4 inches of clear space on all sides of the home theater to ensure adequate ventilation. Do not obstruct the cooling fan or ventilation holes.

| 12 English

HT-E5350_ZC_ENG_0316.indd 12

2012-03-16 3:30:39

Remote Control

Tour of the Remote Control

Turn the product on and off.

To change to TV mode, press the TV button.

To change to Home Theater, press the BD button.

FUNCTION

TV

SOURCE

RECEIVER

SLEEP

BD TV

Press to select Blu-ray's mode (HDMI1, AUX, BD/DVD, etc.).

or

Press to select TV's video mode.

Set a Sleep time to shut off the product.

To open and close the disc tray.

1 2 3

Press numeric buttons to operate		4		5	6
options.
	7			8	9		Use to enter the Popup menu/
			DISC MENU	0	TITLE MENU
Press to view the disc menu.							Title menu.
					POPUP

	Press to skip backwards or forwards.	Press to search backwards or
		forwards.
	Press to stop/play a disc.	Press to pause a disc.
	Cut off the sound temporarily.
		MUTE

Adjust the volume.		VOL S/W LEVEL	TUNING
			/ CH
Press to use Netflix.		HOME	REPEAT

Press to move to the Home screen.

Search for active FM stations and to change channels.

Use to adjust the level of the subwoofer.

Allows you to repeat a title, chapter, track or disc.

Press to use the Tools menu.

Select on-screen menu items and change menu value.

Return to the previous menu.

These buttons are used both for menus on the product and also several Blu-ray Disc functions.

Press to use Smart Hub.

Press this to use the vTuner.

Press to search contents.

Selects the disc audio language.

TUNER

MEMORY

A B C

SMART SEARCH ' '

HUB

vTuner AUDIO SUBTITLE

Use to display the playback information when playing

a Blu-ray/DVD disc.

Press to exit the menu.

Use to set a preset radio frequency.

MO/ST

	D	Select MONO or STEREO for radio
	3DSOUND
		broadcasts.
	SOUND	Press to apply 3D sound effect.
	EFFECT
		Press to apply sound effects.
		Press to enjoy an ordinary 2D video
		in 3D mode.

Selects the disc subtitle language.

English 13 |

Started Getting 02

HT-E5350_ZC_ENG_0316.indd 13

2012-03-16 3:30:41

Getting Started

Installing batteries in the Remote

Control

Battery size: AAA	2
1

|NOTE |

Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.

Assuming typical TV usage, the batteries last for about one year.

The remote control can be used up to approximately 23 feet (7 meters) from the product in a straight line.

Setting the Remote Control

You can control certain functions of your TV with this remote control.

When operating a TV with the remote control

1 . Press the TV button to set the remote control to TV mode.

2 . Turn on your TV.

3 . While holding down the POWER button, enter the code corresponding to your brand of TV.

•If there is more than one code listed for your TV in the table, enter one at a time to determine which code works.

•Example : For a Samsung TV

While holding down the POWER button, use the number buttons to enter 00. If that does not work, try 15, then 16, etc.

4 . If the TV turns off, the setting is complete.

•You can use the TV POWER, VOLUME, CHANNEL, and Numeric buttons (0~9).

|NOTE |

The remote control may not work on some brands of TV's. Also, some operations may not be possible, depending on your brand of TV.

The remote control will work with Samsung TVs by default.

| 14 English

TV Control Codes

Brand	Code
Admiral	56, 57, 58
(M.Wards)
A Mark	01, 15
Anam	01, 02, 03, 04, 05,
	06, 07, 08, 09, 10, 11,
	12, 13, 14
AOC	01, 18, 40, 48
Bell & Howell	57, 58, 81
(M.Wards)
Brocsonic	59, 60
Candle	18
Cetronic	03
Citizen	03, 18, 25
Cinema	97
Classic	03
Concerto	18
Contec	46
Coronado	15
Craig	03, 05, 61, 82, 83, 84
Croslex	62
Crown	03
Curtis Mates	59, 61, 63
CXC	03
	02, 03, 04, 15, 16, 17,
Daewoo	18, 19, 20, 21, 22, 23,
	24, 25, 26, 27, 28,
	29, 30, 32, 34, 35, 36,
	48, 59, 90
Daytron	40
Dynasty	03
Emerson	03, 15, 40, 46, 59, 61,
	64, 82, 83, 84, 85
Fisher	19, 65
Funai	03
Futuretech	03
General	06, 40, 56, 59, 66,
Electric (GE)	67, 68
Hall Mark	40
Hitachi	15, 18, 50, 59, 69
Inkel	45
JC Penny	56, 59, 67, 86
JVC	70
KTV	59, 61, 87, 88
KEC	03, 15, 40
KMC	15
LG (Goldstar)	01, 15, 16, 17, 37,
	38, 39, 40, 41, 42,
	43, 44
Luxman	18
LXI (Sears)	19, 54, 56, 59, 60, 62,
	63, 65, 71
Magnavox	15, 17, 18, 48, 54, 59,
	60, 62, 72, 89
Marantz	40, 54
Matsui	54
MGA	18, 40

Brand	Code
Mitsubishi/	18, 40, 59, 60, 75
MGA
MTC	18
NEC	18, 19, 20, 40, 59, 60
Nikei	03
Onking	03
Onwa	03
Panasonic	06, 07, 08, 09, 54, 66,
	67, 73, 74
Penney	18
Philco	03, 15, 17, 18, 48, 54,
	59, 62, 69, 90
Philips	15, 17, 18, 40, 48,
	54, 62, 72
Pioneer	63, 66, 80, 91
Portland	15, 18, 59
Proton	40
Quasar	06, 66, 67
Radio Shack	17, 48, 56, 60, 61, 75
RCA/Proscan	18, 59, 67, 76, 77, 78,
	92, 93, 94
Realistic	03, 19
Sampo	40
Samsung	00, 15, 16, 17, 40, 43,
	46, 47, 48, 49,
	59, 60, 98
Sanyo	19, 61, 65
Scott	03, 40, 60, 61
Sears	15, 18, 19
Sharp	15, 57, 64
Signature	57, 58
2000
(M.Wards)
Sony	50, 51, 52, 53, 55
Soundesign	03, 40
Spectricon	01
SSS	18
Sylvania	18, 40, 48, 54, 59,
	60, 62
Symphonic	61, 95, 96
Tatung	06
Techwood	18
Teknika	03, 15, 18, 25
TMK	18, 40
Toshiba	19, 57, 63, 71
Vidtech	18
Videch	59, 60, 69
Wards	15, 17, 18, 40, 48,
	54, 60, 64
Yamaha	18
York	40
Yupiteru	03
Zenith	58, 79
Zonda	01
Dongyang	03, 54

HT-E5350_ZC_ENG_0316.indd 14

2012-03-16 3:30:43

Connections

This section describes various methods of connecting the product to other external components. Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

Attaching the Toroidal Ferrite Core to the Power Cord of the Main Unit

If you attach a Toroidal ferrite core to the power cord of the main unit, it will help to prevent RF interference from radio signals.

1.Pull the fixing tab of the Toroidal ferrite core to open it.

2.Make a loop twice in the main unit power cord.

3.Attach the Toroidal ferrite core to the main unit power cord as the figure shows and press it until it clicks.

SPEAKERS OUT

SURROUND

SURROUND

iPod

LAN

WIRELESS

HDMI

Connecting the Speakers

			Position of the product
			Place it on a stand or cabinet shelf, or
	Center		under the TV stand.
Subwoofer			Selecting the Listening Position
		Front (R)
			The listening position should be
	Product	Surround (R)	located about 2.5 to 3 times the
			distance of the TV's screen size
Front (L)			away from the TV. For example, if
			you have a 46 inch screen, locate
Surround (L)			the listening position 115 to 138
			inches (9.6 to11.5 feet) from the
			screen.

Front

Speakers

Center Speaker

Surround

Speakers

Subwoofer

Place these speakers in front of your listening position, facing inwards (about 45°) toward you. Place the front speakers so that their tweeters will be at the same height as your ear. Align the front face of the front speakers with the front face of the center speaker or place them slightly in front of the center speakers.

It is best to install the Center Speaker at the same height as the front speakers. You can also install it directly over or under the TV.

Place these speakers to the side of your listening position. If there isn't enough room, place these speakers so they face each other. Position them about 2 to 3 feet (60 to 90cm) above your ear, facing slightly downward.

*Unlike the front and center speakers, the surround speakers are used mainly for sound effects. Sound will not come from them all the time.

The position of the subwoofer is not so critical. Place it anywhere you like.

English 15 |

Connections 03

HT-E5350_ZC_ENG_0316.indd 15

2012-03-16 3:30:45

Connections

Speaker Components

SCREW (5X20): 12EA		SPEAKER CABLE	SCREW (5X15): 4EA
			CENTER
(L) (R)	(L) (R)

FRONT SURROUND STAND STAND BASE SUBWOOFER

Installing the Speakers on the Tallboy Stand

1.	Turn the Stand Base upside-down and	1	Stand Base					2
2.	connect it to the Stand.
	Use the driver to combine the screws (5x20)
	on the 3 marked holes.

		Stand
3.	Straighten a supplied speaker wire and put in	3	4
4.	the hole on the center of Stand Base.
	Connect the upper Speaker to the assembled
	Stand.

Speaker

Stand

5.	Insert a screw (5x15) clockwise into the hole	5	6
	on the rear of the speaker using a screwdriver.
6.	And then connect a speaker cable.
	This is the appearance after the speaker is
	installed.
	Follow this steps to install other speaker.

| 16 English

HT-E5350_ZC_ENG_0316.indd 16

2012-03-16 3:30:46

Connecting The Speakers

1. Match each speaker cable bundle to the correct speaker by matching the color coded plug on each bundle to the colored sticker on the bottom of each speaker.

2. To attach speaker wire to each speaker:

a. Press down the red tab on the back of the speaker, insert the red wire,	Black	Red
and then release the tab.

b. Press down the black tab on the back of the speaker, insert the black wire, and then release the tab.

3.Connect the speaker wire from each speaker to the back of the product

by matching the colors of the speaker plugs to the colors of the speaker jacks.

Center Speaker

Surround Speaker (L)

Surround Speaker (R)

	SPEAKERS OUT
		: 3
	SURROUND	IMPEDANCE
Front Speaker (L)	SURROUND

Connections 03

SURROUND

SURROUND

iPod

LAN

WIRELESS

HDM

Subwoofer

Front Speaker (R)

English 17 |

HT-E5350_ZC_ENG_0316.indd 17

2012-03-16 3:30:57

Connections

Connecting the Optional Wireless Receiver Module

To connect the surround speakers wirelessly, you have to purchase the wireless receiver module and

TX card from your Samsung retailer.

• This product should be connected with the SWA-5000 only.

		Front
		Speaker (L)
		Center Speaker
Surround	Surround	SPEAKERS OUT
Speaker (L)	Speaker (R)

SURROUND

Front

Speaker (R)

IMPEDANCE : 3

SURROUND

SURROUND

SURROUND

iPod

LAN

WIRELESS

HDM

Subwoofer

Wireless Receiver Module

1.Follow the 1 to 3 steps as shown on the previous page.

2.With the product turned off, insert the TX card into the TX Card Connection (WIRELESS) on the back of the product.

• Hold the TX card so that the label "WIRELESS" faces upward and
insert the card into the port.	LAN	WIRELESS	HDMI OUT

•The TX card enables communication between the product and the wireless receiver module.

3.Connect the left and right surround speakers to the wireless receiver

module. Again, match the color of the plugs to the jacks on the	TX card
wireless receiver module.

4.Plug the power cord of the wireless receiver module into the wall outlet.

5.Turn on the product. The product and wireless receiver module will

now communicate with each other and you will hear sound from the Surround speakers.

| 18 English

HT-E5350_ZC_ENG_0316.indd 18

2012-03-16 3:30:59

| CAUTION |
If you want to install the product on the wall, fasten the screws or nails on the wall firmly and use the holes on the rear of speaker to install.
	However, when you install it, accessories (nails or screws) and installation is not provided by the company.	03
Do not let children play with or near the speakers. They could get hurt if a speaker falls.		Connections
	Do not hang the subwoofer on the wall through the duct (hole).
	When connecting the speaker wires to the speakers, make sure that the polarity (+/–) is correct.

Keep the subwoofer speaker out of reach of children to prevent children from inserting their hands or alien substances into the duct (hole) of the subwoofer speaker.

Do not insert any other card except the TX card dedicated to the product.

If you insert a different TX card, you can damage the product and may not be able to remove the card easily.Do not insert the TX card upside down or in the reverse direction.

Insert the TX card when the product is turned off. Inserting the card when it is turned on may cause a problem.The wireless receiving antenna is built into the wireless receiver module. Keep it away from water and moisture.

For optimal listening performance, make sure that the area around the wireless receiver module location is clear of any obstructions.If you hear no sound from the wireless surround speakers, switch the mode to Dolby Pro Logic II.

In 2-CH mode, you will hear no sound from the wireless surround speakers.

|NOTE |

If you place a speaker near your TV set, the screen color may be distorted because of the magnetic field.

Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too close to the product, sound from the speakers may be disrupted because of interference.

If you use a device such as a microwave oven, wireless LAN Card, or any other device that uses the 2.4/5.8GHz frequencies near the product, sound from the speakers may be disrupted because of interference.

The maximum transmission distance from the product to the wireless receiver module is about 33 feet (10m), but may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the product and the wireless receiver module, the system may not operate at all, because the radio wave cannot penetrate metal.

If the product doesn't make a wireless connection, you need to run an ID Set between the product and wireless receiver module. With the product turned off, press "0""1""3""5" on the remote control. Turn on the wireless receiver module. Then, press and hold the “ID SET” button on the back of the wireless receiver module for 5 seconds, and then turn the product on.

Connecting the FM Antenna

FM Antenna (supplied)

FM ANT

1 . Connect the FM antenna supplied to the FM ANTENNA Jack.

2 . Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or other rigid surface.

|NOTE |

This product does not receive AM broadcasts.

English 19 |

HT-E5350_ZC_ENG_0316.indd 19

2012-03-16 3:31:01

Connections

Connecting to an iPod/iPhone

Using a USB Cable

Connect an iPod/iPhone using the USB cable to the front USB port.

Using a Dock

To view a video from your iPod on your TV, you must also connect the Video Out jack on the product to the Video In jack on your TV. See page 21.

SPEAKERS OUT

SURROUND

SURROUN

IMPEDANCE : 3

WIRELESS	HDMI OUT	1	HDMI IN	2	DIGITAL	FM ANT
					AUDIO IN

|NOTE |

Make sure to connect the dock connector so that the label “” faces upward.

| 20 English

HT-E5350_ZC_ENG_0316.indd 20

2012-03-16 3:31:02

Connecting to a TV

Select either Method 1 or Method 2.

•If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control, and then select the correct external source from the TV's source list (HDMI, Video In, etc.) to view video from the home theater.

AUX

IN

HDMI OUT

1

HDMI IN

2

(Cable not supplied.)

Method 1		Method 2

VIDEO

OUT

OPTICAL

DIGITAL	FM ANT
AUDIO IN

HDMI IN

Method 1 Connecting to a TV with an HDMI Cable - Best Quality (Recommended)

Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI IN jack on your TV.

Method 2 Connecting to a TV with a Video Cable - Good Quality

Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO IN jack on your TV.

|NOTE |

The VIDEO Out jack always outputs in the 480i resolution regardless of the resolution set in the Setup menu.

Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection systems and the picture will be distorted on the television.

English 21 |

Connections 03

HT-E5350_ZC_ENG_0316.indd 21

2012-03-16 3:31:04

Connections

Connecting to External Devices

To select the correct mode for an external device, press the FUNCTION button. Each time you press the button, the mode changes in this order : BD/DVD D. IN AUX R. IPOD HDMI1 HDMI2 FM

R

W

Red

White

(Cable not supplied.)

Method 1

External Devices

		AUX	VIDEO
		IN	OUT
			OPTICAL
1	HDMI IN	2	IN	FM ANT

Method 2	Method 3
(Cable not supplied.)	(Cable not supplied.)

HDMI OUT

OPTICAL OUT

AUDIO OUT

Method 1 HDMI IN : Connecting to an External Component with an HDMI Cable

Connect an HDMI cable (not supplied) from the HDMI IN jack on the back of the product to the HDMI OUT jack on your digital device.  Select the HDMI1 or HDMI2 mode.

Method 2 OPTICAL : Connecting an External Digital Audio Component

To connect the digital audio output of digital signal components such as Cable Boxes and Satellite Receivers (Set-Top-Boxes).

Using a digital optical cable (not supplied), connect the Optical Digital Audio In jack on the product to the Digital Optical Out jack of the external digital device using a digital optical cable.

 Select the D. IN mode.

Method 3 AUX IN : Connecting an External Analog Component

Using an RCA audio cable (not supplied), connect the AUDIO In jack on the product to the AUDIO Out jack on the external analog component.  Select the AUX mode.

• Be sure to match the colors on the cable plugs to the colors on the input and output jacks.

|NOTE |

To see video from your Cable Box/Satellite receiver, you must connect its video output directly to your TV.

This system supports Digital sampling frequencies of 32 kHz or higher from external digital components.

This system supports only DTS and Dolby Digital audio. MPEG audio, a bitstream format, is not supported.

| 22 English

HT-E5350_ZC_ENG_0316.indd 22

2012-03-16 3:31:05

Connecting to a Network Router

Wireless Network

You can connect your product to your network router using one of the methods illustrated below.

Wired Network

Broadband modem (with integrated router)

Broadband

service

Or

Router

Broadband service

Broadband

modem

|NOTE |

Internet access to Samsung’s Software Update server may not be allowed, depending on the router you use or your ISP’s policy. For more information, contact your ISP (Internet Service Provider).

DSL users, please use a router to make a network connection.

To use the AllShare Play function, you must connect your PC to your network as shown in the illustrations on the left.

The connection can be wired or wireless.

Wireless IP sharer

Broadband

service

|NOTE |

If your wireless IP router supports DHCP, this product can use a DHCP or static IP address to connect to the wireless network.

Set your wireless IP router to Infrastructure mode. Ad-hoc mode is not supported.

The product supports only the following wireless security key protocols:

-WEP (OPEN/SHARED), WPA-PSK (TKIP/AES), WPA2-PSK (TKIP/AES)

Select a channel on the wireless IP router that is not currently being used. If the channel set for the wireless IP router is currently being used by another device nearby, it will result in interference and communication failure.

If you select the Pure High-throughput (Greenfield) 802.11n mode and set the Encryption type on your router or AP to WEP, TKIP or TKIP-AES (WPS2Mixed), the product will not support a connection in compliance with new WiFi certification specifications.

Wireless LAN, by its nature, may cause interference, depending on the operating conditions (AP performance, distance, obstacles, interference by other radio devices, etc).

English 23 |

Connections 03

HT-E5350_ZC_ENG_0316.indd 23

2012-03-16 3:31:06

Settings

The Initial Settings Procedure

•The Home menu will not appear if you do not configure the initial settings.

•The OSD (On Screen Display) may change in this product after you upgrade the software version.

•The access steps may differ depending on the menu you selected.

1 . Turn on your TV after connecting the product, and then turn on the product. When you turn on the product for the first time, the product automatically displays the Initial Settings Language screen.

Initial Settings > On-Screen Language

Select a language for the on-screen displays.

		▲	Select English as the
	Dansk	Nederlands
			on-screen menu
	English	Eesti keel	language.
	Suomi	Français	Next
	Deutsch	Ελληνικά
	Magyar	Italiano
	Қазақ
		▼

2 . Use the ▲▼◄► buttons on the remote to select the desired language, and then

press the E button twice. The Start screen appears.

3 . Press the E button to start setup. The Network Settings screen appears.

Initial Settings > Network Settings (1/5)

The next step is to set up a wireless network using an internal LAN Adapter.

Previous

Next

Skip

If you want to connect to your wired network, plug in a network cable.

4 . Press the E button to set up the product's wireless network connection or select

Skip, and then press the E button to skip network setup. If you selected Skip, go to Step 12.

| 24 English

|NOTE |

The product starts the wireless network connection procedure by default. If you want to set up a wired connection, select Skip, and then go to "Configuring Your Network Connection" on page 32 after you have completed the Initial Settings Procedure.

If you skip wireless network setup here, go to "Wireless Network" on page 33 to set up the product's wireless network connection later.

5 . The product searches for and then displays all available wireless router network connections.

Initial Settings > Network Settings (2/5)

	Select your wireless router from the list:	1 / 4
	KIMING_VTOWER	Refresh
	TIAS	WPS(PBC)
	si-ap	Previous
	surlwang5
		Next
	Add Network
		Skip

6 . Use the ▲▼ buttons to select a router, and then press the E button. The Next button is highlighted.

7 . Press the E button to continue. The Security Key screen appears.

|NOTE |

If you have a WPS(PBC) compatible router, select WPS(PBC) instead, press the E button, and then follow the directions on the screen. When done, go to Step 10.

Initial Settings > Network Settings (4/5)
Enter security key.							0 entered		WPS PIN
-
a	b	c	d	e	f	1	2	3	Previous
g	h	i	j	k	l	4	5	6	Next
m	n	o	p	q	r	7	8	9	Skip
s	t	u	v	w	x	y	z	0
	A/a			Space				

8 . Enter your network's security key. When done, use the ▲▼◄► buttons to select Next, and then press the E button.

HT-E5350_ZC_ENG_0316.indd 24

2012-03-16 3:31:08

|NOTE |

Enter numbers by pressing the number buttons on your remote.

Enter letters by selecting a letter using the ▲▼◄► buttons, and then press the E button.

To display capital letters (or redisplay small letters if capital letters are displayed), select A/a, and then press the E button.

To display symbols and punctuation, select , and then press the E button. To redisplay letters, select , and then press the E button.

9 . If the connection is successful, the Connection Complete screen appears. Select Next, and then press the E button. The Software Update screen appears.

|NOTE |

If the connection is not successful, select Next, and then press the E button. After you have completed the Initial Settings procedure, go to "Wireless Network" on page 33 to set up the product's wireless network connection.

10 . To upgrade the software, select Update now, and then press the E button. To skip the upgrade, select Update later, press the E button, and go to Step 12.

|NOTE |

If you skipped network set up, you must skip Software Update also.

11 . If there is a Software Update available, the product downloads and installs the upgrade. This can take some time. If there

is no Software Update available, the "There are no new software updates for you to download. You already have the most up to date version." message appears. And then, press the E button. The TV Aspect Ratio screen appears.

Initial Settings > TV Aspect Ratio

Set to match the type of television connected.

16:9	Original
16:9	Full

	4:3 Letter Box	Select when connecting to a	Previous
			Next
		16:9 TV Screen. All content
	4:3 Pan-Scan	will be displayed at original
		aspect ratio. Content
		formatted in 4:3 will be
		displayed with black bars on
		left and right.

12 . Using the ▲▼ buttons, select the aspect ratio that matches your screen, and then press the E button. Select Next, and then press the E button.

You have four choices:

16:9 Original - For widescreen TVs. Displays widescreen pictures in their original 16:9 format and 4:3 pictures (the old, standard format) in 4:3 pillar box format with black bars on the left and right.

16:9 Full - For widescreen TVs. Displays widescreen pictures in their original 16:9 format and expands 4:3 pictures to fill the 16:9 screen.

4:3 Letter Box - For older, standard screen analog TVs. Displays 4:3 pictures in full screen and 16:9 pictures in letter box format that retains the 16:9 aspect ratio but puts black bars above and below the picture. 4:3 Pan-Scan - For older, standard screen analog TVs. Displays 4:3 pictures in full

screen and 16:9 pictures in Pan-Scan format that fills the screen, but cuts off the left and right sides of the picture and enlarges the middle vertically.

Initial Settings > Complete
Setup completed.
On-Screen Language		Press Smart Hub to
Network Settings		enjoy variety of
		Internet content.			OK
Software Update	-
TV Aspect			Smart Hub

13 . The Setup completed screen appears. Check the settings to confirm they are correct. Select OK, and then press the E button. The Home screen appears.

|NOTE |

If you want to display the Initial Setting screen again and make changes, select the Reset option. (See page 31)

If you use an HDMI cable to connect the product to an Anynet+ (HDMI-CEC)-compliant Samsung TV and 1.) You have set the Anynet+ (HDMI-CEC) feature to ON in both the TV and the product and 2.) You have set the TV to a language supported by the product, the product will select that language as the preferred language automatically.

English 25 |

Settings 04

HT-E5350_ZC_ENG_0316.indd 25

2012-03-16 3:31:10

Settings

The Home Screen

AllShare Play

Play videos, photos, or music from Disc or connected devices.

23

	1		4
		Function	Settings
	Smart Hub

2 . To access the menus, sub-menus, and options on the Settings screen, please refer to the remote control illustration below.

|NOTE |

If you leave the product in the stop mode for more than 5 minutes without using it, a screen saver will appear on your TV. If the product is left in the screen saver mode for more than 20 minutes, the power will automatically turn off.

Buttons on the Remote Control Used for the Settings Menu

1Smart Hub. Starts Smart Hub. From Smart Hub, you can access YouTube, games, and other apps.

2AllShare Play. Play videos, photos or music content from Disc, USB, PC or mobile devices.

3Function. Select the audio/video input source.

4Settings. Set various functions to suit your personal preferences.

Selecting an Option on the Home Screen

1 . To select an option on the Home screen, move the cursor using the ◄► buttons until it highlights the option of your choice, and then press the E button.

Accessing the Settings Screen

1 . Select Settings on the Home screen, and then press E. The Settings screen appears.

	Display	3D Settings	16:9 Original
		TV Aspect Ratio
	Audio	Smart Hub Screen Size	Size 3
	Network	BD Wise	Off
		Resolution	Auto
	System	Movie Frame (24Fs)	Auto
		HDMI Color Format	Auto
	Support	HDMI Deep Color	Auto
		Progressive Mode	Auto

| 26 English

1

3 24

1HOME Button : Press to move to the Home screen.

2RETURN Button : Return to the previous menu.

E (Enter) / DIRECTION Button :

~Press ▲▼◄► to move the cursor or select

3an item.

~Press the E button to activate the currently selected item or confirm a setting.

4EXIT Button : Press to exit the current menu.

|NOTE |

The E button on the product's front panel can be used for same purpose as the E button on the remote control.

Detailed Function Information

Each Settings function, menu item, and individual option is explained in detail on-screen. To view an explanation, use the ▲▼◄► buttons to select the function, menu item, or option.

The explanation will usually appear on the right of the screen. A short description of each Settings function starts on the next page. Additional information on some of the functions is also in the Appendix of this manual.

HT-E5350_ZC_ENG_0316.indd 26

2012-03-16 3:31:11

Settings Menu Functions

Display			Set up the 3D related functions.
			3D Blu-ray Playback Mode: Select whether to play a Blu-
			ray Disc with 3D contents in 3D Mode. If you move to the
		3D Settings	Home or Smart Hub Home menu while in 3D mode, the
			product will switch to 2D automatically.
			Screen Size: Enter the size of the TV attached to the
			product. The product will automatically adjust the 3D output
			to the screen size of the TV.
		TV Aspect	Lets you adjust the output of the product to the screen size of
			your TV. See page 25, Step 12 for a description of the screen
		Ratio	size options.
		Smart Hub	Lets you select the optimal size for the Smart Hub Screen.
		Screen Size
			BD Wise is Samsung’s latest inter-connectivity feature.
		BD Wise	When you connect a Samsung product and a Samsung TV
			with BD Wise to each other via HDMI, and BD Wise is on in
			both the product and TV, the product outputs video at the
			video resolution and frame rate of the Blu-ray/DVD Disc.
			Lets you set the output resolution of the HDMI video signal to
			Auto, 1080p, 1080i, 720p, 480p. If Composite is connected,
		Resolution	the resolution supports only 480i. The number indicates
			the number of lines of video per frame. The i and p indicate
			interlaced and progressive scan, respectively. The more lines,
			the higher quality.
			Setting the Movie Frame (24Fs) feature to Auto lets the product
			adjust its HDMI output to 24 frames per second automatically
		Movie Frame	for improved picture quality if attached to a 24Fs compatible TV.
			• You can enjoy the Movie Frame (24Fs) feature only on a TV
		(24Fs)	supporting this frame rate.
			• Movie Frame is only available when the product is in the
			HDMI 1080i or 1080p output resolution modes.
		HDMI Color	Lets you set the color space format for the HDMI output to
		Format	match the capabilities of the connected device (TV, monitor, etc).
		HDMI Deep	Lets you set the product to output video from the HDMI OUT
			jack with Deep Color. Deep Color provides more accurate
		Color	color reproduction with greater color depth.
		Progressive	Lets you improve picture quality when viewing DVDs.
		Mode

English 27 |

Settings 04

HT-E5350_ZC_ENG_0316.indd 27

2012-03-16 3:31:22

Settings

Audio	Speaker	You can set the speaker options.
	Settings
	Equalizer	Let you configure the Equalizer settings manually.
	Smart Volume	Lets you set the product so that the volume remains stable
		when a scene change occurs or when you change the
		channel.
	Speaker	Lets you select which speakers you want active, either the
	Selection	TV's speakers or the Home theater's speakers.
		Lets you direct the sound from the TV to the Home Theater
		speakers. Requires an HDMI connection and an Audio Return
		Channel (ARC) compatible TV.
	Audio Return	• When Audio Return Channel set to on, use HDMI Cable to
		connect the product to the TV. At this time, optical input
	Channel	does not work.
		• When Audio Return Channel set to auto, use HDMI Cable to
		connect the product to the TV. At this time, ARC and optical
		input is selected automatically.
	Digital Output	Let you set the Digital Output to match the capabilities of the
		AV receiver you’ve connected to the product. For more details,
		please refer to the digital output selection table. (See page 59)

Lets you apply dynamic range control to Dolby Digital, Dolby

Digital Plus, and Dolby True HD audio.

Auto: Automatically controls the dynamic range of Dolby TrueHD audio, based on information in the Dolby TrueHD

Dynamic	soundtrack. Also turns dynamic range control on for Dolby
Range Control	Digital and Dolby Digital Plus.

Off: Leaves the dynamic range uncompressed, letting you hear the original sound.

On: Turns dynamic range control on for all three Dolby formats. Quieter sounds are made louder and the volume of loud sounds is reduced.

When the product is attached to a digital TV, lets you adjust Audio Sync the audio delay so that the audio syncs with the video. You

can set the delay between 0 and 300 milliseconds.

| 28 English

HT-E5350_ZC_ENG_0316.indd 28

2012-03-16 3:31:23

Network	Network	For more information about Network Settings and network
		functions, see "Networks and the Internet" starting on page
	Settings	32.
	Network	Let you check whether a connection to the network and the
	Status	Internet have been established.
	Wi-Fi Direct	Lets you connect a Wi-Fi Direct device to the product using a
		Peer-to-Peer network, without a wireless router. You can use
		the device to control the product.
		Lets you connect other types of Wi-Fi devices to the product
	Soft AP	wirelessly. Requires that you create a security key which
		you must enter into the other Wi-Fi devices when you are
		connecting them to the network.
	AllShare	Lets you permit external devices such as smart phones to
		connect to the product and share content with or control the
	Settings	product.
	Device Name	Lets you assign an identifying name to the product. You use
		this name to identify the product when you are connecting
		external Wi-Fi devices (smart phones, tablets, etc.) to it.
	BD-Live	Lets you allow, limit, or prohibit an Internet connection for the
	Settings	BD-Live service.

English 29 |

Settings 04

HT-E5350_ZC_ENG_0316.indd 29

2012-03-16 3:31:24

Settings

System	Initial Settings	Lets you re-run the Initial Settings procedure. See page 24 for
		details.
		You can connect a wireless USB keyboard or mouse to
		the USB port on the front of the product.
		Keyboard Settings: Lets you configure a wireless USB
		keyboard connected to the product.
		| NOTE |
		You can use the keyboard only when a QWERTY keyboard screen or
		window appears in the Web Browser.
		Mouse Settings: Lets you configure a wireless USB mouse
		connected to the product. You can use the mouse in the
		product's menu in the same way you use a mouse on your
		PC.
	Device	To use a mouse with the product's menu:
	Manager	1 . Connect the USB mouse to the product.
		2 . Click the primary button you selected in Mouse Settings.
		The Simple Menu appears.
		3 . Click the menu options you want.
		| NOTE |
		Depending on the model of the USB HID keyboard and mouse may not
		be compatible with your product.
		Some HID keyboard keys may not work.
		Wired USB keyboards are not supported.
		Some applications may not be supported.
		If a wireless HID Keyboard does not operate because of interference,
		move the keyboard closer to the product.
		Anynet+ is a convenient function that offers linked operations
	Anynet+	with other Samsung products that have the Anynet+ feature
		and lets you control those products with one Samsung TV
	(HDMI-CEC)	remote. To operate this function, you must connect this
		product to an Anynet+ Samsung TV using an HDMI cable.
		You can select the language you prefer for the On-Screen
	Language	menu, disc menu, subtitles, etc.
		• The language you select for the disc menu, disc audio, or
		subtitles will only appear if it is supported on the disc.

| 30 English

HT-E5350_ZC_ENG_0316.indd 30

2012-03-16 3:31:24