Samsung HPS5033X/XAA, HPS4233X/XAA User Manual

SP-S4223 HP-S4233 HP-S5033

PLASMA DISPLAY

Owner’s Instructions

This device is a Class B digital apparatus.

Important Warranty Information Regarding Television Format Viewing

Wide screen format PDP Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature and the images are constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on nonexpanded standard format television video and programming, should be limited to no more than 5% of the total television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary

images that exceed the above guidelines can cause uneven aging of PDP Displays that leave subtle, but permanent burned-in ghost images in the PDP picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars.

On PDP models that offer picture sizing features, use these controls to view different formats as a full screen picture.

Be careful in the selection and duration of television formats used for viewing. Uneven PDP aging as a result of format selection and use, as well as burned-in images, are not covered by your Samsung limited warranty.

English-2

User Instructions

Screen Image retention

Do not display a still image (such as on a video game) on the plasma display panel for more than several minutes as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, refer to page 26 of this manual to reduce the degree of brightness and contrast of the screen when displaying a still image.

Altitude

The PDP can only operate normally at heights under 6500ft.

Heat on the top of the PDP TV

The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.

The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.

Cell Defects

The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology to produce. However, there may be a few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.

Avoid operating the TV at temperatures below 5°C (41°F)

A still image displayed too long may cause permanent damage to the PDP Panel.

Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and center of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.

Afterimage on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images for a long time.

Warranty

Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.

English-3

Contents

GENERAL INFORMATION

List of Features .................................................................................. 5

Accessories........................................................................................ 5

Viewing the Control Panel.................................................................. 6

Viewing the Connection Panel........................................................... 7

Remote Control.................................................................................. 8

Installing Batteries in the Remote Control ......................................... 9

CONNECTIONS

Connecting VHF and UHF Antennas................................................. 9

Connecting Cable TV......................................................................... 10

Connecting a VCR ............................................................................. 11

Connecting an S-VHS VCR ............................................................... 11

Connecting a Camcorder ................................................................... 12

Connecting a DVD Player/Set-Top Box............................................. 12

Connecting a DVD Player/Set-Top Box via DVI ................................ 12

Connecting a DVD Player/Set-Top Box via HDMI............................. 13

Connecting a Digital Audio System.................................................... 13

Connecting an Amplifier/DVD Home Theater .................................... 14

Connecting a PC................................................................................ 14

OPERATION

Turning the TV On and Off ............................................................... 15

Plug & Play Feature........................................................................... 15

Changing Channels ........................................................................... 17

Adjusting the Volume ......................................................................... 18

Viewing the Display............................................................................ 18

Viewing the Menus............................................................................. 18

Memorizing the Channels .................................................................. 19

Setting Up Your Remote Control........................................................ 20

To Select the Source .......................................................................... 25

To Edit the Input Source Name .......................................................... 25

PICTURE CONTROL

Using Automatic Picture Settings ................................................. 26

Digital Noise Reduction ................................................................ 27

Changing the Screen Size............................................................ 28

DNIe (Digital Natural Image engine) ............................................ 29

Selecting the Film Mode............................................................... 29

Setting the Blue Screen Mode...................................................... 29

Viewing Picture-in-Picture............................................................. 30

Freezing the Current Picture ........................................................ 31

CHANNEL CONTROL

Selecting the Antenna................................................................... 36

Adding and Erasing Channels...................................................... 36

To set-up Your Favorite Channels ............................................... 37

Viewing the Channel Lists ............................................................ 38

Setting the Default Channel List Mode......................................... 38

Labeling Channels ....................................................................... 39

Fine Tuning Analog Channels....................................................... 39

Checking the Digital-Signal Strength............................................ 40

LNA (Low Noise Amplifier)............................................................ 40

PC DISPLAY

Using Your TV as a Computer (PC) Display ................................ 41

Display Modes .............................................................................. 41

Setting up the TV with your PC .................................................... 42

TIME SETTING

Setting the Time............................................................................ 44

FUNCTION DESCRIPTION

Selecting a Menu Language......................................................... 47

Using the Game Mode.................................................................. 47

Viewing Closed Captions (On-Screen Text Messages) - Digital .. 48

Viewing Closed Captions (On-Screen Text Messages) - Analog

Menu Transparency Level ............................................................ 50

Using the Energy Saving Feature ................................................ 50

Preventing Screen Burn-in ........................................................... 51

Reducing the Effects of Screen Burn ........................................... 52

Setting the Function Help ............................................................ 52

Using the V-Chip........................................................................... 53

APPENDIX

Identifying Problems .................................................................... 59

Wall Installation Instructions ......................................................... 60

How to assemble the Stand-Base ................................................ 62

Specifications................................................................................ 62

Dimensions (SP-S4223/HP-S4233).............................................. 63

Dimensions (HP-S5033)............................................................... 64

... 49

SOUND CONTROL

Using Automatic Sound Settings.................................................. 32

Customizing the Sound ................................................................ 32

Setting the TruSurround XT.......................................................... 33

Choosing a Multi-Channel Sound (MTS) track - Digital .............. 33

Choosing a Multi-Channel Sound (MTS) track - Analog ............. 34

Automatic Volume Control ........................................................... 34

Selecting the Internal Mute........................................................... 35

Setting the On/Off Melody ............................................................ 35

Listening to the Sound of the Sub (PIP) Picture .......................... 35

Symbol Press Important Note One-Touch

➢

Button

English-4

General Information

List of Features

 Adjustable picture settings that can be stored in the TV’s memory.  Automatic timer to turn the TV on and off.  Aspecial sleep timer.  V-Chip function.  Excellent Digital Interface & Networking :

With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Set-Top Box needed.

 Remote Control

The supplied remote can be used to operate the TV as well as most DVD players, Set-top boxes, Cable Boxes and VCRs.

 Excellent Picture Quality

DNIe technology provides life-like clear images.

 SRS TruSurround XT

SRS TruSurround XT provides a virtual Dolby surround system.

Accessories

Please make sure the following items are included with your TV. If any items are missing, contact your dealer.

Remote Control

(BN59-00511A) /

AAA Batteries

(4301-000103)

The following parts are sold separately and are available at most electronics stores.

S-VIDEO Cable (BN39-00149A)

PC Cable

(BN39-00115A)

➢

Ferrite Core (Power Cord, Audio/Video Cable, S-Video Cable)

The ferrite cores are used to shield the cables from interference. When connecting a cable, open the ferrite core and clip it around the cable near the plug.

Power Cord

(3903-000144)

PC Audio Cable (BN39-00061B)

Owner’s Instructions /

Quick Setup Guide

HDMI Cable

(BN39-00641A)

Optical Cable Coaxial Cable

Warranty Card /

Registration Card /

Safety Guide Manual

(Not available in all locations)

HDMI/DVI cable

(BN39-00643A)

Ferrite Core for

(BN39-00110A)

Power Cord

(3301-001110)

Component Cables (RCA)

Ferrite Core for

(3301-001305)

(BN39-00279A)

Antenna Cable

(BN39-00333A)

Side-AV

English-5

Viewing the Control Panel

Buttons on the Lower-Right Par

The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control.

t of the Panel

SOURCE

Toggles between all the available input sources (TV, AV1, AV2, S-Video1, S-Video2, Component1, Component2, PC, HDMI1, or HDMI2).

Press to see an on-screen menu of your TV’s features.

ˇ + VOL –

Press to increase or decrease the volume. In the on-screen menu, use the you would use the œœand √√buttons on the remote control.

¨ CH

Press to change channels. In the on-screen menu, use the you would use the ……and††buttons on the remote control.

(ENTER)

Press to confirm a selection.

+ VOL –

buttons as

English-6

POWER

Press to turn the TV on and off.

Power Indicator

Blinks and turns off when the power is on and lights up in stand-by mode.

Remote Control Sensor

Aim the remote control towards this spot on the TV.

∏

Speakers

Viewing the Connection Panel

Rear Panel Jacks

Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players. For more information on connecting equipment, see pages 9-14.

POWER IN

Connect the supplied power cord.

HDMI IN 2

Connect to the HDMI jack of a device with HDMI output.

HDMI 1/DVI IN

Connect to the HDMI jack of a device with HDMI output. This input can also be used as a DVI connection with separate analog audio inputs. An optional HDMI/DVI cable will be necessary to make this connection. When using an optional HDMI/DVI adapter, the DVI analog audio inputs on your TV allow you to receive left and right audio from your DVI device. (Not compatible with PC)

DVI IN (AUDIO-L/R)

Connect to the DVI audio output jack of an external device.

OPTICAL DIGITAL AUDIO OUT

Connect to a Digital Audio component.

COAXIAL DIGITAL AUDIO OUT

Connect to a Digital Audio component.

∏

ANT 1 IN (CABLE)/ANT 2 IN (AIR)

75Ω Coaxial connector for Air/Cable Network.

”

PC AUDIO IN

Connect to the audio output jack on your PC.

’

PC IN

Connect to the video output jack on your PC.

SERVICE 1/SERVICE 2

These jacks are for service purposes only.

AUDIO-L/R (AV IN 1)

Audio inputs for external devices, such as a camcorder or VCR.



VIDEO (AV IN 1)

Video input for external devices, such as a camcorder or VCR.

S-VIDEO (AV IN 1)

Video input for external devices with an S-Video output, such as a camcorder or VCR.

COMPONENT IN 1, 2

Video (Y/PB/PR) and audio (L-AUDIO-R) component inputs.

AUDIO OUT (L/R)

Audio outputs for external devices.

Side Panel Jacks

Use the left side panel jacks to connect a component that is used only occasionally, such as a camcorder or video game. (See page 12)

S-VIDEO IN 2

S-Video input for external devices with an S-Video output.

AV IN 2

Video and audio inputs for external devices.

HEADPHONE

You can connect a set of headphones to your television if you wish to watch a television program without disturbing other people in the room.

English-7

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always point it directly at the TV. You can also use your remote control to operate your VCR, Cable box, DVD player, or Set-Top Box.

Œ POWER

Turns the TV on and off.

´ NUMERIC BUTTONS

Press to change the channel.

ˇ –

Press to select additional channels (digital and analog) being broadcast by the same station. For example, to select channel “54-3”, press “54”, then press “–” and “3”.

¨ CH MGR

Used to display Channel Lists on the screen.

ˆ ANTENNA

Press to select “AIR” or “CABLE”.

Ø VCR/DVD Functions

- Rewind

- Stop

- Play/Pause

- Fast/Forward

∏

+ VOL –

Press to increase or decrease the volume.

” MUTE

Press to temporarily cut off the sound.

’ MENU

Displays the main on-screen menu.

˝ S.MODE

Press to select the sound mode.

Ô PIP

Picture-in Picture ON/OFF.

 P. MODE

Press to select the picture mode.

Ò SRS

Selects SRS TruSurround XT mode.

Ú MTS

Press to choose stereo, mono or Separate Audio Program (SAP broadcast).

Æ AUTO PROG.

Press to automatically store selected Air/Cable channels.

ı ADD/DEL

Use to store and delete channels to/from memory.

˜ SET

Sets the remote to control your TV, VCR, Cable, DVD, or Set-Top Box.

¯ TV, DVD, STB, CABLE, VCR

Press to operate your TV, DVD, STB, CABLE (box), or VCR.

˘ SOURCE

Press to display all of the available video sources.

¿ PRE-CH

Tunes to the previous channel.

¸ FAV.C H

Press to switch to your favorite channels.

˛ E.SAVING

Adjusts screen brightness to save energy.

◊ CH

Press to change channels.

± EXIT

Press to exit the menu.

≠ UP / DOWN / LEFT /

RIGHT / ENTER

Use to select on-screen menu items and change menu values.

– INFO

Press to display information on the TV screen.

— SLEEP

Press to select a preset time interval for

automatic shut off.

÷ STILL

Press to stop the action during a particular scene. Press again to resume normal video.

® P.SIZE

Press to change the screen size.

∑ SWAP

Switches the main and sub (PIP) picture.

µ CH

Displays the available channels in sequence. (These buttons change channels in the PIP window only.)

¥ CAPTION

Controls the caption decoder.

≥ RESET

When your remote does not work, change the batteries and press the RESET button for 2-3 seconds before use.

➢ This is a special remote control for the visually impaired, and has Braille points on the Power,

Channel and Volume buttons.

English-8

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the figure.

2. Install two AAA size batteries.

➢

Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.

3. Replace the cover.

➢

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV. (Assuming typical TV usage, the batteries last for about one year.)

➢

If the remote control doesn’t work, check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage, or is the power cord unplugged?

5. Is there a special fluorescent light or neon sign nearby?

Connections

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like this, see “Antennas with 300 ΩFlat Twin Leads” below.

If your antenna has one lead that looks like this, see “Antennas with 75 ΩRound Leads”. If you have two antennas, see “Separate VHF and UHF Antennas”.

Antennas with 300 Ω Flat

Twin Leads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300 Ωtwin flat leads, follow the directions below.

1. Place the wires from the twin leads under the screws on a 300-75Ωadapter (not supplied). Use a screwdriver to tighten the screws.

2. Plug the adaptor into the ANT 1 IN (CABLE) terminal on the back of the TV.

ANT 1 IN (CALBE)

Antennas with 75 Ω Round Leads

1. Plug the antenna lead into the ANT 2 IN (AIR) terminal on the back of the TV.

ANT 2 IN (AIR)

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

1. Connect both antenna leads to the combiner.

UHF

VHF

2. Plug the combiner into the ANT 2 IN (AIR) terminal on the bottom of the back panel.

UHF

VHF

ANT 2 IN (AIR)

English-9

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

1. Plug the incoming cable into the ANT 1 IN (CABLE) terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.

ANT 1 IN (CALBE)

Connecting to a Cable Box that Descrambles All Channels

ANT IN

ANT OUT

ANT 1 IN (CALBE)

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of Antenna cable. (These items are available at most electronics stores.)

➢

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.

➢

2. Connect the other end of this cable to the ANT 1 IN (CABLE) terminal on the back of the TV.

1. Find and disconnect the cable that is

ANT IN

connected to the ANT IN terminal on your cable box.

This terminal might be labeled “ANT IN”,

➢

“VHF IN” or simply, “IN”.

2. Connect this cable to a two-way splitter.

Incoming

cable

Splitter

3. Connect an Antenna cable between an OUTPUT terminal on the splitter and the

Incoming

cable

Splitter

Cable Box

IN terminal on the cable box.

4. Connect an Antenna cable between the ANT OUT terminal on the cable box and

Incoming

cable

Splitter

Cable Box

RF (A/B)

Switch

the B–IN terminal on the RF(A/B) switch.

5. Connect another cable between the other OUT terminal on the splitter and the A–IN

Incoming

cable

Incoming

cable

Splitter

Cable Box

RF (A/B)

Switch

RF (A/B)

Switch

TV Rear

ANT 1 IN (CABLE)

After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)

terminal on the RF (A/B) switch.

6. Connect the last Antenna cable between the OUT terminal on the RF (A/B) switch and the ANT 1 IN (CABLE) terminal on the rear of the TV.

English-10

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 9-10). Skip step 1 if you have not yet connected to an antenna or a cable system.

1. Unplug the cable or antenna from the back of the TV.

2. Connect the cable or antenna to the ANT IN terminal on the back of the VCR.

3. Connect an Antenna Cable

TV Rear Panel

VCR Rear Panel

➢

Each external input source device has a different back panel configuration.

➢

When connecting an external device, match the color of the connection terminal to the cable.

Audio Cable (Not supplied)

Video Cable (Not supplied)

Antenna Cable (Not supplied)

between the ANT OUT terminal on the VCR and the ANT 1 IN (CABLE) or ANT 2 IN (AIR) terminal on the TV.

4. Connect a Video Cable between the VIDEO OUT jack on the VCR and the AV IN 1 [VIDEO] jack on the TV.

5. Connect Audio Cables between the AUDIO OUT jacks on the VCR and the AV IN 1 [R-AUDIO-L] jacks on the TV.

➢

If you have a “mono” (non-stereo) VCR, use a Y-connector (not supplied) to hook up to the right and left audio input jacks of the TV. If your VCR is stereo, you must connect two cables.

Connecting an S-VHS VCR

Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR. (This connection delivers a better picture as compared to a standard VHS VCR.)

TV Rear Panel

VCR Rear Panel

Audio Cable (Not supplied)

S-Video Cable (Not supplied)

Antenna Cable (Not supplied)

An S-Video cable is usually included with an S-VHS VCR. (If not, check your local electronics store.)

➢

Each external input source device has a different back panel configuration.

➢

When connecting an external device, match the color of the connection terminal to the cable.

➢

Some games may be displayed with a cut off picture when the TV is connected to a game player.

1. To begin, follow steps 1–3 in the previous section to connect the antenna or cable to your VCR and your TV.

2. Connect an S-Video Cable between the S-VIDEO OUT jack on the VCR and the AV IN 1 [S-VIDEO] jack on the TV.

3. Connect Audio Cables between the AUDIO OUT jacks on the VCR and the AV IN 1 [R-AUDIO-L] jacks on the TV.

English-11

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow you to view the camcorder tapes without using a VCR

TV Side Panel

S-Video Cable (Not supplied)

Video Cable (Not supplied)

Camcorder

➢

Each external input source device has a different back panel configuration.

➢

When connecting an external device, match the color of the connection terminal to the cable.

Audio Cable (Not supplied)

Connecting a DVD Player/Set-Top Box

The rear panel jacks on your TV make it easy to connect a DVD player/Set-Top Box to your TV.

DVD Player / Set-Top Box

Audio Cable (Not supplied)

Component Cable (Not supplied)

➢

Component video separates the video into Y (Luminance (brightness)), P for enhanced video quality. Be sure to match the component video and audio connections. For example, if connecting the video cable to COMPONENT IN, connect the audio cable to COMPONENT IN also.

➢

Each external input source device has a different back panel configuration.

➢

When connecting an external device, match the color of the connection terminal to the cable.

TV Rear Panel

(Blue) and PR(Red)

1. Connect a Video Cable (or S-Video Cable) between the AV IN 2 [VIDEO] (or S-VIDEO) jack on the TV and the VIDEO OUT jack on the camcorder.

2. Connect Audio Cables between the AV IN 2 [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the camcorder.

1. Connect a Component

Cable between the COMPONENT IN 1 [Y, P PR] (or COMPONENT IN 2 [Y, PB, PR]) jacks on the TV and the COMPONENT [Y, PB, PR] jacks on the DVD player/Set-Top Box.

2. Connect Audio Cables

between the COMPONENT IN 1 [R-AUDIO-L](or COMPONENT IN 2 [R-AUDIO-L]) jacks on the TV and the AUDIO OUT jacks on the DVD player/ Set-Top Box.

Connecting a DVD Player/Set-Top Box via DVI

This connection can only be made if there is a DVI Output jack on the external device.

DVD Player / Set-Top Box

Audio Cable (Not supplied)

DVI to HDMI Cable (Not supplied)

➢

Each external input source device has a different back panel configuration.

➢

When connecting an external device, match the color of the connection terminal to the cable.

TV Rear Panel

English-12

1. Connect a DVI to HDMI

Cable or DVI-HDMI Adapter between the HDMI 1/DVI IN jack on the TV and the DVI jack on the DVD player/ Set-Top Box.

2. Connect Audio Cables

between the DVI IN [R-AUDIO-L] jack on the TV and the AUDIO OUT jacks on the DVD player/ Set-Top Box.

Connecting a DVD Player/Set-Top Box via HDMI

This connection can only be made if there is an HDMI Output jack on the external device.

TV Rear Panel

DVD Player/Set-Top Box

HDMI Cable (Not supplied)

DVI to HDMI Cable (Not supplied)

What is HDMI?

• HDMI, or high-definition multimedia interface, is a next-generation interface that enables the transmission of digital audio and video signals using a single cable without compression.

• “Multimedia interface” is a more accurate name for it especially because it allows multiple channels of digital audio (5.1 channels). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed, and supports multi-channel digital audio.

➢

Each external input source device has a different back panel configuration.

➢

When connecting an external device, match the color of the connection terminal to the cable.

➢

When connecting via HDMI, you do not need to connect Audio Cables. You only need to connect Audio cables when connecting via HDMI/DVI.

TV Rear Panel

Audio Cable (Not supplied)

Connect an HDMI Cable

between the [HDMI1/DVI IN] or [HDMI IN 2] on the TV and the HDMI OUT on the DVD player/Set-Top Box or connect a DVI to HDMI Cable or DVI-HDMI Adapter between the [HDMI1/DVI IN] jack on the TV and the DVI jack on the DVD player/SetTop Box.

If connecting via HDMI/DVI, you must also connect audio cables. Connect Audio Cables between the DVI IN [L-AUDIO-R] jacks on the TV and the AUDIO OUT jacks on the DVD player/Set-Top Box.

Connecting a Digital Audio System

The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV.

Digital Audio System

TV Rear Panel

Optical Cable (Not supplied)

What is OPTICAL?

• Converts the electric signal into an optical light signal, and transmits it through glass fibers. S/PDIF

is a transmission system of digital audio in the form of a light wave that uses a glass conductor.

What is COAXIAL:?

• The digital audio signal is received through a coaxial copper cable.

➢

5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.

➢

Each external input source device has a different back panel configuration.

Coaxial cable (Not supplied)

1. Connect an Optical or Coaxial Cable between the DIGITAL AUDIO OUT (OPTICAL or COAXIAL) jacks on the TV and the Digital Audio Input jacks on the Digital Audio System.

When a Digital Audio System is connected to the “DIGITAL AUDIO OUT (OPTICAL or COAXIAL)” terminal: Decrease the gain (volume) of the TV, and adjust the volume level with the system’s volume control.

English-13

Connecting an Amplifier/DVD Home Theater

Amplifier/DVD Home Theater

Audio Cable (Not supplied)

➢

Each external input source device has a different back panel configuration.

➢

When connecting an external device, match the color of the connection terminal to the cable.

TV Rear Panel

Connecting a PC

1. Connect Audio Cables between the AUDIO OUT [R-AUDIO-L] on the TV and AUDIO IN [R-AUDIO-L] on the Amplifier/DVD Home Theater.

When an audio amplifier is connected to the “AUDIO OUT [R-AUDIO-L]” terminals: Decrease the gain (volume) of the TV, and adjust the volume level with the Amplifier’s volume control.

TV Rear Panel

PC Audio Cable (Not supplied)

D-Sub Cable (Not supplied)

➢

Each external input source device has a different back panel configuration.

➢

When connecting an external device, match the color of the connection terminal to the cable.

➢

The HDMI/DVI jacks do not support PC connection.

Internal Speakers

Internal Mute Off

Internal Mute On

Video No Signal

When “Internal Mute” is set to “On”, Sound menus except “Multi-Track Options” cannot be adjusted.

Speaker Output

Mute

AV, S-Video

Speaker Output

Mute

Component, PC, HDMI

Speaker Output

Mute

Audio Out (Optical, Coaxial, L/R Out)

Sound Output

Mute

1. Connect a D-Sub Cable

between PC IN [PC] jack on the TV and the PC output jack on your computer.

2. Connect a PC Audio Cable

between PC IN [AUDIO] jack on the TV and the Audio Out jack of the sound card on your computer.

AV, S-Video

Sound Output

Mute

Component, PC, HDMI

Sound Output

Mute

English-14

Operation

Turning the TV On and Off

Press the POWER button on the remote control. You can also use the POWER button on the TV.

Plug & Play Feature

When the TV is initially powered On, basic customer settings proceed automatically and subsequently:

1. Press the POWER button on the remote control.

Menu language, Channels

and Time will be set.

Start

The message “Menu language, Channels and Time will be set.” is displayed. Press the ENTER button, then “Select the language of the OSD” menu is automatically displayed.

Plug & Play

Select the language of the OSD.

Menu Language :

Move

Select the antennas to memorize.

Air Cable Air + Cable

Move

Select the cable system.

STD HRC IRC

English

Spanish French

Enter Skip

Plug & Play

Enter Skip

Plug & Play

Enter SkipMove

Start Start Start

2. Press the ENTER button to enter the language. Press the ……or ††button to select language, then press the ENTER button. “Select the antennas to memorize.” menu is automatically displayed.

3. Press the ……or ††button to memorize the channels of the selected connection. Press the ENTER button to select “Start”.

➢

If the antenna is connected to ANT 2 IN (AIR), select “Air” and if it is connected to ANT 1 IN (CABLE), select “Cable”.

➢

If both ANT 2 IN (AIR) and ANT 1 IN (CABLE) are connected, select the “Air + Cable”.

➢

In Cable mode, you can select the correct signal source among STD, HRC, and IRC by pressing the ……or ††button, then press the ENTER button. Contact your local cable company to identify the type of cable system that exists in your particular area.

English-15

Continued...

Plug & Play

Auto Program in progress.

Cable Channel 67

Stop

Enter Skip

Plug & Play

Auto Program is completed. 14 Channels were memorized.

Air : 9 , Cable : 5.

Enter Skip

Plug & Play

Select the clock mode.

Clock Mode :

Manual

Auto

4. The TV will begin memorizing all of the available channels. After all the available channels are stored, the Auto program menu reappears. Press the ENTER button when channel memorization is complete. “Clock Mode” menu is automatically displayed.

➢

To stop the search before it has finished, press the ENTER button with Stop selected.

5. Press the ENTER button. Press the ……or ††button to select “Manual” for setting the current time manually, then press the ENTER button. “Set current date and time.” is displayed.

➢

If you select “Auto”, “Set to daylight savings time.” is displayed, then go to step 8.

Move

Enter Skip

Clock Set

Set current date and time.

Month Day Year

…

-- -- ----

†

Hour Minute am/pm

-- -- --

Adjust

Enjoy your watching.

Enter Skip

Setting the Clock Automatically

Plug & Play

Set to daylight savings time.

Daylight Savings Time :

Move

Select the time zone in which you live.

Newfoundland Atlantic

Eastern

Central Mountain Pacific Alaska Hawaii

Plug & Play

Enjoy your watching.

Yes

Enter Skip

Enter SkipMove

6. Press the œ or √ button to move to “Month”, “Day”, “Year”, “Hour”, “Minute”, or “am/pm”. Set the date and time you want by pressing the … or † button, then press the MENU button.

➢

You can set the month, day, year, hour and minute directly by pressing the number buttons on the remote control.

7. The message “Enjoy your watching.” is displayed. When you have finished, press the ENTER button.

➢

Even if the ENTER button is not pressed, the message will automatically disappear after several seconds.

8. Press the ENTER button. Press the ……or ††button to select “No” or “Yes”, then the ENTER button. “Select the time zone in which you live.” menu is automatically displayed.

9. Press the ……or ††button to highlight the time zone for your local area (and to move the highlight to the appropriate time zone on the map of the United States). Press the ENTER button. If not, see page 44 to set the clock.

10. The message “Enjoy your watching.” is displayed. When you have finished,press the ENTER button.

➢

Even if the ENTER button is not pressed, the message will automatically disappear after several seconds.

English-16

If you want to r

eset this feature...

Setup

Plug & Play Language : English Time

Game Mode : Off

V-Chip Caption

†

Move Enter Return

1. Press the MENU button to display the menu.

√ √ √

√

√ √

Press the ……or ††button to select “Setup”, then press the ENTER button.

2. Press the ENTER button to select “Plug & Play”.

Menu language, Channels

and Time will be set.

Start

For further details on setting up options, refer to the page 15~16.

➢

Plug & Play can only be accessed in the TV mode.

Changing Channels

Using the Channel Buttons

1. Press the CH or CH button to change channels.

➢

When you press the CH or CH button, the TV changes channels in sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels). You will not see channels that were either erased or not memorized. See page 19 to memorize channels.

Using the Number Buttons

Use the number buttons to quickly tune to any channel.

1. Press the number buttons to go directly to a channel. For example, to select channel 27, press “2,” then “7.” The TV will change channels when you press the second number.

Using the “-” Button

The “-” button is used to select stations that broadcast both a digital and analog signal.

1. For example, for Channel 7-1 (digital), press “7”, then “-”, then “1”. For channel 7-2 (analog), press “7”, then “-”, then “2”.

HD indicates the TV is receiving a Digital High Definition signal.

➢

SD indicates the TV is receiving a Standard Definition signal.

➢

For quick channel change, press the number buttons, then press the ENTER button.

Using the PRE-CH Button to select the Previous Channel

1. Press the PRE-CH button. The TV will switch to the last channel viewed.

➢

To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Then use the PRE-CH button to quickly alternate between them.

English-17

Adjusting the Volume

1. Press the

VOL +

VOL –

button to increase or decrease the volume.

Using the Mute Button

At any time, you can cut off the sound using the MUTE button.

1. Press MUTE and the sound cuts off. The word “Mute” will appear in the lower-left corner of the screen.

2. To turn mute off, press the MUTE button again, or simply press the VOL +

VOL –

button.

Viewing the Display

The display identifies the current channel and the status of certain audio-video settings.

Air 28

Mono Picture Mode : Dynamic

Sound Mode : Custom MTS : Stereo

12 : 00 am

1. Press the INFO button on the remote control.

The TV will display the channel, the type of sound, and the status of certain picture and sound settings.

Viewing the Menus

Source List : TV Edit Name

Move Enter Return

Input

Press the INFO button once more or wait approximately 10 seconds and it disappears automatically.

1. With the power on, press the MENU button.

√ √

The main menu appears on the screen. Its left side has five icons: Input, Picture, Sound, Channel, Setup.

2. Use the ……or ††button to select one of the five icons. Then press the ENTER button to access the icon’s sub-menu.

3. Press the EXIT button to exit.

The on-screen menus disappear from the screen after a few seconds.

➢

English-18

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (air) and cable channels. After the available channels are memorized, use the CH or CH button to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an air or a cable system).

Antenna : Air Auto Program Channel Manager Name Fine Tune Signal Strength

†

Antenna :

Auto Program Channel Manager Name Fine Tune Signal Strength

†

Channel

Move Enter Return

Channel

Air

Cable

Move Enter Return

1. Press the MENU button to display the menu.

√ √ √ √ √ √

Press the ……or ††button to select “Channel”, then press the ENTER button.

2. Press the ENTER button select “Antenna”. Press the ……or ††button to select “Air” or “Cable”, then press the ENTER button.

Press the EXIT button to exit.

Storing Channels in Memor

Antenna : Air Auto Program Channel Manager Name Fine Tune Signal Strength

†

Select the antennas to memorize.

Air Cable Air + Cable

Select the cable system.

STD

HRC IRC

Auto Program in progress.

Channel

Move Enter Return

Auto Program

Move Enter Return

Auto Program

Move Enter

Auto Program

Cable Channel 67

Stop

Enter Return

y (Automatic Method)

1. Press the MENU button to display the menu.

√ √ √ √ √ √

Press the ……or ††button to select “Channel”, then press the ENTER button.

2. Press the ……or ††button to select “Auto Program”, then press the ENTER button.

3. Press the ……or ††button to select the antenna connection, then press the

ENTER button.

Start Start Start

➢

➢ ➢

4. Select the correct signal source (STD, HRC, and IRC) by pressing the ……or button, then press the ENTER button.

➢

Return

5. The TV begins memorizing all available stations. Press the ENTER button at any time to interrupt the memorization process. Press the EXIT button to exit.

➢

You can also press the AUTO PROG. button on the remote control to bring up the Auto Program menu.

Air: “Air” antenna signal. Cable: “Cable” antenna signal. Air+Cable: “Air” and “Cable” antenna signals.

If the antenna is connected to ANT 1 IN (CABLE), select “Cable” and if it is connected to ANT 2 IN (AIR), select “Air”. If both ANT 1 IN and ANT 2 IN are connected, select the “Air + Cable”. If you selected “Air”, then go to step 5.

††

STD, HRC, and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected.

The TV must be connected to an antenna in order to receive digital TV signals. Even if a particular channel is deleted from the memory, you can always tune to that channel directly by using the number buttons on the remote control.

• All available DTV and analog channels are automatically stored in memory.

• It takes approximately 3 to 10 minutes to memorize channels.

English-19

Setting Up Your Remote Control

After it has been set up properly, your remote control can operate in five different modes: TV, VCR, Cable, DVD, or Set-Top Box. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose.

The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top Boxes.

➢

Setting Up the Remote to Operate Your VCR

Turn off your VCR.

Press the VCR button on your TV’s remote control.

Press the SET button on your TV’s remote control.

Using the number buttons on your remote control, enter three digits of the VCR code listed on page 22 of this manual for your brand of VCR. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)

Press the POWER button on the remote control. Your VCR should turn on if your remote is set up correctly.

If your VCR does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of VCR. If no other codes are listed, try each VCR code, 000 through 080.

Note on Using Remote Control Modes: VCR When your remote control is in “VCR” mode, the volume buttons still control your TV’s volume.

Setting Up the Remote to Operate Your Cable Box

Turn off your cable box.

Press the CABLE button on your TV’s remote control.

Press the SET button on your TV’s remote control.

Using the number buttons on your remote control, enter three digits of the cable box code listed on page 23 of this manual for your brand of cable box. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)

Press the POWER button on the remote control. Your cable box should turn on if your remote is set up correctly.

If your cable box does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of cable box. If no other codes are listed, try each code, 000 through 046.

Note on Using Remote Control Modes: Cable Box When your remote control is in “CABLE” mode, the volume buttons still control your TV’s volume.

English-20

Continued...

Setting Up the Remote to Operate Your DVD

Turn off your DVD.

Press the DVD button on your TV’s remote control.

Press the SET button on your TV’s remote control.

Using the number buttons on your remote control, enter three digits of the DVD code listed on page 24 of this manual for your brand of DVD. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)

Press the POWER button on the remote control. Your DVD should turn on if your remote is set up correctly.

If your DVD does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of DVD. If no other codes are listed, try each code, 000 through 141.

Note on Using Remote Control Modes: DVD When your remote control is in “DVD” mode, the volume buttons still control your TV’s volume.

Setting Up the Remote to Operate Your Set Top Box

Turn off your STB.

Press the STB button on your TV’s remote control.

Press the SET button on your TV’s remote control.

Using the number buttons on your remote control, enter three digits of the STB code listed on page 23 of this manual for your brand of STB. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)

Press the POWER button on the remote control. Your STB should turn on if your remote is set up correctly.

If your STB does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of STB. If no other codes are listed, try each code, 000 through 074.

Note on Using Remote Control Modes: STB When your remote control is in “STB” mode, the volume buttons still control your TV’s volume.

Continued...

English-21

+ 47 hidden pages