Samsung HP-P5581 User Manual
Quick Guide
Connections
Connecting CableCARD
You must obtain a CableCARD from a local cable service provider.
PDP
Power cord
From cable TV
Please insert the card
as shown.
Connecting a VCR
Connecting a VCR to the Video or S-Video/Audio jack
Connect the Video/Audio cables between the VIDEO or S-VIDEO / L - AUDIO - R jacks on the PDP and VIDEO or S-VIDEO / L - AUDIO - R output jacks
on the VCR. (Note: For better video, use an S-Video cable.)
PDP
VCR
Connecting a DVD Player (480i, 480p)
This PDP displays the optimum picture in 720p mode.
PDP DVD Player
Power cord
Connecting a DTV Receiver (480p, 720p, 1080i)
This PDP displays the optimum picture in 720p mode.
PDP
Component cable
Audio cable
DTV Receiver
Connecting a Digital TV Set-Top Box (480p, 720p, 1080i)
By inputting a high-bandwidth digital content protection High-Definition picture source to the DVI IN jack on the TV, High-Definition pictures can be
displayed on the screen in their digital form.
PDP
Power cord
Audio cable
DVI cable
Use a DVI-D video cable.
DTV Set-Top Box
From cable
or Antenna
Connecting a Digital Audio System
There are many types of digital audio systems on the market today. A simplified illustration of an audio system is shown below. For more information,
see your audio system owner’s manual.
PDP
Digital Audio System
Power cord
Audio cable
S-Video cable
Video cable
Connecting a Camcorder
Viewing camcorder tapes
Connect a Video/Audio cable between the VIDEO or S-VIDEO / L - AUDIO - R jacks on the PDP and the VIDEO or S-VIDEO /AUDIO output jacks on
the camcorder. (Note: For better video, use an S-VIDEO cable.)
S-Video cable
Camcorder
PDP(SIDE AV2)
PDP
REAR PANEL
Power cord
or
Component cable
Audio cable
DVI cable
Use a DVI-D video cable.
Connecting to HDMI (High Definition Multimedia Interface) (480p, 720p, 1080i)
PDP
HDMI cable
DTV Set-Top Box
Power cord
Power cord
or
Connecting to an Analog Amplifier/Sub woofer Speaker
PDP
Power cord
Audio cable
Coaxial cable
Optical cable
Powered Subwoofer
(Option)
Power cord
Audio cable
Video cable
Analog Amplifier
Quick Guide
Remote Control ButtonsOperation Front Panel Information Window
Selecting a broadcast source
Before your television can begin memorizing the available channels,
you must specify the type of signal source that is connected to the TV
(i.e., an antenna or a cable system).
Press the MENU button.
Press the … or † button to select
“Channel”, then press the ENTER
button.
Press the … or † button to select
“Auto Program”, then press the
ENTER button.
Press the … or † button to select the
antenna connection, then press the
ENTER button.
NOTES
• Air : “Air” antenna signal.
• Cable : “Cable” antenna signal.
• Air+Cable : “Air” and “Cable”
antenna signals.
If the CableCARD is inserted into the
“CableCARD” slot on the rear panel,
“Cable” and “Air+Cable” are not
available.
When selecting Cable TV system :
Press the … or † button to select
“Cable”, then press the ENTER button.
Press the … or † button to select
“STD”, “HRC”, or “IRC”, then press the
ENTER button.
NOTE
• STD, HRC, and IRC identify various
types of cable TV systems. Contact
your local cable company to identify
the type of cable system that exists in
your particular area. At this point the
signal source has been selected.
Proceed to “Storing Channels in
Memory”.
ChannelTV
Antenna : Air
Auto Program
Add / Delete
Favorite Channels
Name
Fine Tune
† More
Move Enter Return
ChannelTV
Antenna : Air
Auto Program
Add / Delete
Favorite Channels
Name
Fine Tune
† More
Move Enter Return
Auto ProgramTV
Select the antennas to memorize
Air
Cable
Air + Cable
Select the antennas to memorize
Air
Cable
Air + Cable
Select the cable system.
STD
HRC
IRC
Start
Start
Start
Move Enter Return
Auto ProgramTV
Start
Start
Start
Move Enter Return
Auto ProgramTV
Move Enter Return
Storing Channels in Memory (Automatic Method)
Press the … or † button to select the
antennas to memorize. Press the ENTER
√
button to select “Start”.
√
√
√
√
√
Press the ENTER button to start the auto
√
program. The TV begins memorizing all
√
available stations.
√
√
Press the ENTER button at any time to
√
√
interrupt the memorization process.
Press the EXIT button to exit.
NOTE
• The TV must be connected to an
antenna in order to receive digital
TV signals.
Even if a particular channel is deleted
from the memory, you can always
tune to that channel directly by using
the number buttons on the remote
control.
NOTES
• All available DTV and analog channels are automatically stored in
memory when channels are selected by the direct tuning function.
• It takes approximately 3 to 10 minutes to memorize channels.
Channel Memory in Process
Auto ProgramTV
Select the antennas to memorize
Air
Cable
Air + Cable
Auto Program
Start
Start
Start
Move Enter Return
AIR Channel 67
Stop
Enter Return
’
ΠSOURCE button
Press to display all of the available video sources
(TV, AV1, AV2, S-VIDEO1, S-VIDEO2,
COMPONENT, DVI, and HDMI).
´ MENU button
Displays the main on-screen menu.
ˇ VOL(+,-) button
Press to increase or decrease the volume.
Also used to select or adjust items on the
on-screen menu.
¨ CH( , ) button
Press CH or CH to change channels.
Also used to move up or down in the on-screen
menu.
”
TOUCH button
Touch the right side of each button to
operate.
ˆ ENTER( ) button
Press to confirm a selection.
Ø Power Indicator
- Power Off : Red
- Power On : Off
- Timer On : Green
∏
Press to turn the PDP on and off.
” Remote Control Signal Receiver
Aim the remote control towards this spot on
the PDP.
’ Speakers
Œ
´
ˇ
¨
ˆ
Ø
∏
Remote Control
ΠPOWER button
Turns the PDP on and off.
´ ANTENNA button
Press to select “AIR” or “CABLE”.
ˇ Number buttons
-
button
¨
Press to select additional channels (digital and analog) being broadcast by the same
station. For example, to select channel “54-3”, press “54”, then press “
ˆ MUTE button
Press to mute the PDP sound.
Ø VOL (Volume) buttons
Use to adjust volume.
∏ GUIDE button
Press to display the on-screen Electronic Program Guide (EPG).
” MENU button
Displays the main on-screen menu.
’ ENTER button
Confirms a selection.
˝ FAV. CH button
Press to switch to your favorite channels.
Ô CH. LIST
Displays the channel list.
LCD Display
When you press a button, ‘ ‘ appears along with selected mode (TV, VCR, CATV,
DVD, or STB) and the remote's battery charge status.
Ò P.MODE button
Adjusts the PDP picture by selecting one of the preset factory settings (or select your
personal, customized picture settings).
Ú MODE button
Selects a target device to be controlled by the Samsung remote control (i.e., VCR,
Cable box, DVD players, or Samsung STB). If you change modes, the new mode is
momentarily displayed on LCD.
Æ PRE-CH button
Tunes to the previous channel.
ı SOURCE button
Press to display all of the available video sources
S-VIDEO2, COMPONENT, DVI, and HDMI).
˜ CH (Channel) buttons
Use to switch channels.
¯ INFO button
Press to display information on the PDP screen.
˘ EXIT button
Press to exit the menu.
¿ Up/Down Left/Right buttons
Control the cursor in the menu.
¸ MTS button
Press to choose stereo, mono or Separate Audio Program (SAP broadcast).
˛ PIP button
Activates picture in picture.
◊ ASPECT button
Press to change the screen size.
± STILL button
Press to pause the current screen.
≠ DNIe button
Activates DNIe (Digital Natural Image engine).
– SRS button
Selects TruSurround XT mode.
(TV, AV1, AV2, S-VIDEO1,
-
” and “3”.
— SET button
Used during set up of this Samsung remote control,
so that it will work compatibly with other devices
(VCR, Cable Box and DVD).
÷ SLEEP button
Press to select a preset time interval for automatic
shut off.
® PIP control buttons
CH
,
: Press to change PIP channels.
(Only Analog channels can be viewed
through PIP.)
∑ CAPTION button
Controls the caption decoder.
µ VCR, DVD control buttons
Controls VCR tape or DVD disc functions:
Stop, Rewind, Play/Pause, and Fast Forward.
¥ RESET button
If your remote control is not functioning properly,
take out the batteries and press the reset button
for about 2~3 seconds.
Re-insert the batteries and try using the remote
control again.
BN68-00766A
Loading...