Owner’s Instructions
HP-P4261
This device is a Class B digital apparatus.
2
Important Warranty Information
Regarding Television Format Viewing
User Instructions
Wide screen format PDP Displays (16:9,the aspect ratio of the screen width to height) are primarily
designed to view wide screen format full-motion video. The images displayed on them should primarily be
in the wide screen 16:9 ratio format,or expanded to fill the screen if your model offers this feature and the
images are constantly moving. Displaying stationary graphics and images on screen, such as the dark
side-bars on nonexpanded standard format television video and programming, should be limited to no
more than 5% of the total television viewing per week.
Additionally,viewing other stationary images and text such as stock market reports, video game
displays,station logos,web sites or computer graphics and patterns,should be limited as described above
for all televisions. Displaying stationary images that exceed the above guidelines can
cause uneven aging of PDP Displays that leave subtle,but permanent burned-in
ghost images in the PDP picture. To avoid this,vary the programming and images,
and primarily display full screen moving images,not stationary patterns or dark bars.
On PDP models that offer picture sizing features,use these controls to view different formats as a full screen
picture.
Be careful in the selection and duration of television formats used for viewing. Uneven PDP aging as a
result of format selection and use,as well as burned-in images, are not covered by your Samsung limited
warranty.
Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma
display panel for more than several minutes as it can cause screen image retention. This image retention is
also known as “screen burn”. To avoid such image retention, refer to page 40 of this manual to reduce the
degree of brightness and contrast of this screen when displaying a still image.
Cell Defect
The plasma display panel consists of fine cells. Although the panels are produced with more than 99.9
percent active cells, there may be some cells that do not produce light or remain lit.
Altitude
The PDP will not operate normally at altitudes above 6500 ft.
Warranty
Warranty does not cover any damage caused by image retention.
Burn-in is not covered by the warranty.
3
General Information
Your New Plasma Display Panel ......................6
Remote Control Buttons ..................................8
Wall Installation Instructions ..........................10
How to assemble the Stand-Base ..................14
Connections
Connecting VHF and UHF Antennas ..............16
Connecting Cable TV ..................................17
Connecting a VCR ......................................19
Connecting a Camcorder ............................20
Connecting a DVD Player ............................21
Connecting a DTV Receiver ..........................22
Operation
Turning the PDP On and Off ........................28
Plug & Play Feature......................................30
Memorizing the Channels ............................33
Setting Up Your Remote Control ....................38
Viewing an External Signal Source ..............40
Picture Control
Customizing the Picture ..............................44
Using Automatic Picture Settings ..................45
Selecting the Color Tone ..............................46
DNIe (Digital Natural Image engine) ............47
Changing the Screen Size ..........................48
Freezing the Picture ...................................50
Viewing the Picture-in-Picture .......................51
Selecting a Signal Source (Antenna or Cable) for PIP
.....56
Setting the MCC(My Control Color) Mode .....58
Sound Control
Customizing the Sound ................................64
Using Automatic Sound Settings ...................65
Choosing a Multi-Channel Sound (MTS)Soundtrack
......66
Using the Auto Volume ................................67
Setting the TruSurround XT ............................68
Listening to the Sound of the Sub(PIP) Picture ..69
Selecting the Internal Mute............................70
Channel Control
Fine Tuning Channels ..................................72
LNA (Low Noise Amplifier) ..........................73
Connecting a PC and Operation
Connecting a PC ........................................76
Adjusting the PC Screen ..............................80
Changing the Position of the Image................81
Picture Quality Adjustment ..........................82
Information ................................................85
Time Setting
Setting the Clock ........................................88
Setting the Sleep Timer ................................89
Setting the Timers ........................................90
Function Description
Selecting a Menu Language ........................94
Digital Noise Reduction ..............................95
Selecting the Film Mode ..............................96
Using the Color Weaknees Enhancement Option
..97
Setting the Melody Sound ............................98
Setting the Blue Screen ................................99
Setting the Fan ..........................................100
Viewing Closed Captions ..........................101
Using the V-Chip........................................102
Appendix
Troubleshooting ........................................110
Care and Maintenance ..............................111
Specifications............................................112
Table of Contents
PLASMA DISPLAY PANEL
General Information
Your New Plasma Display Panel ......................................................6
Remote Control Buttons ..................................................................8
Wall Installation Instructions ..........................................................10
How to assemble the Stand-Base ....................................................14
Front Panel
Your New Plasma Display Panel
6
Checking Accessories
Owner’s Instructions
(BN68-00645A)
Once you have unpacked your PDP, check to make sure that you have all the parts shown here.
If any piece is missing or broken, call your dealer.
Remote Control/AAA Batteries
(BN59-00377D)
Power Cord (3903-000085) Antenna Cable (BN39-00333A)
S-VIDEO Cable
PC Cable
DVI Cable
Component Cables (RCA)
PC Audio Cable
Sold Separately
SOURCE button
Press to display all of the available video sources
(TV, AV1, AV2, AV3, S-VIDEO1, S-VIDEO2, COMPONENT1,
COMPONENT2, PC, DVI).
MENU button
Displays the main on-screen menu.
VOL(+,-) button
Press to increase or decrease the volume. Also used to
select or adjust items on the on-screen menu.
CH( , ) button
Press CH or CH to change Channels.
Also used to move up or down in the On-screen menu.
ENTER( ) button
Press to confirm a selection.
I/
Press to turn the PDP on and off.
Power Indicator
- Power Off: Blue
- Power On: Off
Remote Control Signal Receiver
Aim the remote control towards
this spot on the PDP.
Speakers
7
Rear Panel
Side of the TV
ŒDVI INPUT (DVI-D / L-AUDIO-R)
Connect to the digital video and audio
output jack for device with DVI output.
´MONITOR OUT (VIDEO / L-AUDIO-R)
Outputs for external devices.
ˇPC INPUT (RGB IN / AUDIO)
Connect to the video and audio output
jack on your PC.
¨FOR SERVICE ONLY
Connector for service only.
ˆS-VIDEO1, S-VIDEO2
(S-VIDEO1 or S-VIDEO2 / L-AUDIO-R)
Video and audio inputs for external
devices with an S-Video output, such as
a camcorder or VCR.
ØAV1, AV2, AV3
(VIDEO / L-AUDIO-R )
Video and audio inputs for external
devices, such as a camcorder or VCR.
∏COMPONENT1, COMPONENT2
Video (Y/Pb/Pr) and audio (L-AUDIO-R)
inputs for Component.
”ANT IN VHF/UHF (75Ω)
75Ω Coaxial connector for
Antenna/Cable Network.
’ POWER IN
Connect the supplied power cord.
Audio Input (L, R)
Video Input
S-Video Input
Remote Control Buttons
ŒPOWER button
Turns the PDP on and off.
´ASPECT button
Press to change the screen size.
ˇNumber buttons
¨+100 button
Press to select channels over 100. For example, to select
channel 121, press “+100”, then press “2” and “1.”
ˆMUTE button
Press to mute the PDP sound.
ØVOL (Volume) buttons
Use it to adjust volume.
∏SLEEP button
Press to select a preset time interval for automatic shutoff.
”MENU button
Displays the main on-screen menu.
’ENTER button
Confirms a selection.
˝PIP button
Activates picture in picture.
ÔSTILL button
Press to pause the current screen.
LCD Display
When you press a button, ‘ ‘ appears along with
selected mode (TV, VCR, CATV, DVD or STB) and
remaining batteries on LCD.
ÒP.MODE button
Adjust the PDP picture by selecting one of the preset
factory settings (or select your personal, customized
picture settings.)
ÚMODE button
Selects a target device to be controlled by the Samsung
remote control (i.e., VCR, Cable, DVD players or STB).
If you change modes, the new mode is momentarily
displayed on LCD.
ÆPRE-CH button
Tunes to the previous channel.
ıTV/VIDEO button
Press to display all of the available video sources
(TV, AV1, AV2, AV3, S-VIDEO1, S-VIDEO2, COMPONENT1,
COMPONENT2, PC, DVI).
˜CH (Channel) buttons
Use it to switch channels.
¯INFO button
Press to display information on the PDP screen.
˘EXIT button
Press to exit the menu.
¿Up/Down Left/Right buttons
Control the cursor in the menu.
8
Remote Control
¸SRS TSXT button
Selects Trusurround XT mode.
˛ MTS button
Press to choose stereo, mono or Separate Audio Program (SAP broadcast).
◊AUTO PROG. button
The TV automatically cycles through all of the available channels and stores them in memory.
±ADD/DEL button
Press to add or delete channels in the TV’s memory.
≠DNIe button
Activates DNIe (Digital Natural Image engine).
–CAPTION button
Controls the caption decoder.
—SET button
Used during set up of this Samsung remote control,
so that it will work compatibly with other devices
(VCR, cable box, DVD)
÷PIP control buttons
SWAP : Exchanges the video signal that is
currently displayed on the main screen
with the signal in the PIP window.
SIZE : Press to make the PIP window Large,
Small or Double.
CH
,
: Displays the available channels in
sequence. (These buttons change channels
in the PIP window only).
®VCR, DVD control buttons
Controls VCR tape or DVD disc functions: Stop,
Rewind, Play/Pause, Fast Forward.
∑RESET button
If your remote control is not functioning properly, take
out the batteries and press the reset button for about
2~3 seconds. Re-insert the batteries and try using the
remote control again.
9
Installing the Batteries in Your Remote Control
1
Slide the back cover
to open the battery
compartment of the
remote control.
3
Slide the cover back into
place.
2
Install two AAA size batteries. Make sure to match the
“+” and “-” ends of the batteries with the diagram
inside the compartment.
Remote Control Operation Range.
You can use your remote control within a distance of 23 feet and an angle of 30 degrees
from the left and right sides of the PDP’s remote control receiver.
Wall Installation Instructions
10
Screws ; 4 EA
Insulation Holder ; 4 EA
1
Do not install the PDP on any location other than a vertical wall.
2
To protect the performance of the PDP and prevent problems, avoid the following locations:
• Do not install next to smoke and fire detectors.
• Do not install in an area subjected to vibration or high voltage.
• Do not install near or around any heating apparatus.
3
Use only recommended parts and components.
Installation Notes
Parts (Wall attachment panel is sold separately. Check with your dealer)
Wall Mount Bracket
➤
➤
This wall mount bracket installation guide is for the following model : HP-P4261
Loading...