Samsung HL-R5656W, HL-R4656W, HL-R6156W, HL-R5056W User Manual

Owner’s Instructions
HL-R4656W HL-R5056W HL-R5656W HL-R6156W
Register your product at www.samsung.com/global/register
• What is Digital Television?
Digital television (DTV) is a new way of transmitting high quality video and audio to your TV set. Using DTV, broadcasters can transmit high definition TV (HDTV) images, Dolby digital surround audio, and new services such as multicasting (transmitting more than one program on the same TV channel) and datacasting. Several of these services can be combined into a single digital broadcast.
Digital Television Services
• Digital Picture Quality
DTV programs are transmitted in two different formats. The first is Standard Definition Television (SDTV) and the second is High Definition Television (HDTV).
• SDTV program formats include 480-line interlaced (480i) and 480-line progressive (480p) video.
480i programs are essentially a digital version of our current analog TV programs, while the 480p format offers improved image detail over 480i. Some 480p programs are broadcast in widescreen and are comparable to progressive-scan DVD movies in image quality.
• HDTV program formats include 1080-line interlaced (1080i) and 720-line progressive (720p).
Both HDTV formats are always broadcast in widescreen, and offer much higher picture quality than SDTV.
• Dolby Surround Sound
With DTV, you can listen to a variety of Dolby digital audio formats from Dolby Surround 2.0 to Dolby Digital 5.1 surround, using your home audio system. Many HDTV programs are now broadcast with DD 5.1 soundtracks.
U.S.A Only
The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. In particular, this product is licensed under the following US patents: 5,991,715, 5,740,317, 4,972,484, 5,214,678, 5,323,396, 5,539,829, 5,606,618, 5,530,655, 5,777,992, 6,289,308, 5,610,985, 5,481,643, 5,544,247, 5,960,037, 6,023,490, 5,878,080, and under US Published Patent Application No. 2001-44713-A1.
This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
Other countries
The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
English - 2
Q&A
1. Is the antenna I use for existing TV reception good enough for DTV?
Over-the-air (OTA) digital TV broadcasting uses the same channels as analog TV and works well with many existing TV antennas. However, DTV broadcast channel assignments are different than analog channels. You should find out whether your local DTV broadcasts are on VHF (channels 2-13) or UHF (channels 14-69) to see if you need a different antenna.
If your DTV channels are on UHF and you already get good UHF reception, your present antenna may work fine. The same holds true for VHF DTV reception. Note that in some markets, both VHF and UHF channels are used for DTV broadcasts.
You can find out the latest DTV channel assignments for your area by browsing selected Internet web sites such as www.titantv.com, www.10000watts.com, and www.fcc.gov.
2. How difficult is it to receive DTV signals indoors?
This depends on whether your local DTV stations are running full power or not and how close your location is to the transmission tower. DTV receivers do not require as much signal as analog TV receivers to produce high-quality images and sound.
Once the DTV signal level exceeds a certain threshold at the receiver, the digital video and audio data is decoded at the same quality it was originally encoded for broadcast. This is a big advantage for DTV over analog TV - there is no noise, ghosting, static, or scratchy audio.
3. How can I connect an antenna in my townhouse, co-operative apartment, condominium, or apartment?
The Federal Communications Commission’s OTARD Rule (part of the Telecommunications Act of
1996) allows residents of condominiums, townhouse, or members of neighborhood associations to put up outside antennas for reception of broadcast TV signals as long as those antennas are not located in common areas and are no more than 12’ in height.
Residents of rental units (apartments, etc.) are not covered by the OTARD rules and will have to use indoor antennas to receive DTV broadcasts. It is possible that the landlord of an apartment complex can provide broadcast DTV signals via a master TV antenna system to each apartment.
4. Can I connect my DTV set-top receiver to my cable TV service?
Cable TV systems use a different method for transmitting digital TV programs that is currently incompatible with broadcast DTV set-top receivers. So you will still need to use an outdoor or indoor antenna to receive OTA broadcast DTV programs.
The good news is that you won’t have to pay a monthly or per-program charge to watch OTA DTV and HDTV programs. They’re free, unlike subscription satellite TV or premium cable TV. All you need is an antenna and a DTV set-top receiver to enjoy clear, sharp widescreen images and high-quality audio.
English - 3
Table of Contents
Your New Wide TV...................................................................................8
Viewing Position ......................................................................................................8
List of Features.........................................................................................................9
Checking Accessories...............................................................................................9
Right side buttons...................................................................................................10
Side Panel Jacks ................................................................................................... 10
Front Panel LED Indicators.......................................................................................11
Rear Panel Jacks....................................................................................................12
Remote Control......................................................................................................13
Connections ...........................................................................................16
Connecting VHF and UHF Antennas ........................................................................16
Antennas with 75-ohm Round Leads ..............................................................16
Connecting Cable TV .............................................................................................17
Cable without a Cable Box...........................................................................17
Cable with a Cable Box that Descrambles All Channels...................................17
Cable with a Cable Box that Descrambles Some (But Not All) Channels ............18
Connecting a VCR .................................................................................................19
Connecting a VCR to the Video or S-Video/Audio jack....................................19
Connecting a Camcorder .......................................................................................20
Connecting a DVD Player .......................................................................................21
Connecting to Y, P
Connecting to Audio and Video Jacks............................................................21
Connecting a DTV Set-Top Box ................................................................................22
Connecting to Y, P
Connecting to DVI (Digital Visual Interface) ....................................................22
Connecting to HDMI (High Definition Multimedia Interface) ..............................23
Connecting a Digital Audio System..........................................................................24
Connecting to an Analog Amplifier..........................................................................24
B, PR.................................................................................21
B, PR.................................................................................22
Operation ..............................................................................................26
Turning the TV On and Off .....................................................................................26
Viewing the Menus and On-Screen Displays .............................................................26
Selecting a Menu Language....................................................................................27
Memorizing the Channels .......................................................................................28
Adding and Erasing Channels.................................................................................30
Changing Channels ...............................................................................................31
Customizing Your Remote Control ............................................................................32
Remote Control Codes............................................................................................33
Setting the Clock....................................................................................................34
Setting the On/Off Timer........................................................................................36
Setting the Sleep Timer ...........................................................................................37
Viewing an External Signal Source ..........................................................................38
Assigning Names to External Input Mode .................................................................39
English - 4
Channel Control .....................................................................................42
Selecting Your Favorite Channels .............................................................................42
Labeling the Channels ............................................................................................43
Fine Tuning Analog Channels ........................................................................44
Checking the Digital-Signal Strength ..............................................................45
Analog
Digital
LNA (Low Noise Amplifier) .....................................................................................46
Picture Control........................................................................................48
Picture Control.......................................................................................................48
Changing the Picture Size.......................................................................................51
Digital Noise Reduction..........................................................................................52
Viewing the DNIe Demonstration.............................................................................53
Setting the My Color Control Mode .........................................................................54
Using the Color Weakness Enhancement Feature.......................................................56
Setting the Film Mode ............................................................................................57
Freezing the Picture................................................................................................58
Setting the Blue Screen Mode..................................................................................59
Sound Control ........................................................................................62
Sound Control .......................................................................................................62
Auto Volume..........................................................................................................64
Choosing a Multi-Channel Sound (MTS) track .................................................65
Choosing a Multi-Channel Sound (MTS) track .................................................66
Choosing a Digital Sound Format ..................................................................67
Digital
Selecting the Internal Mute......................................................................................68
Setting the On/Off Melody.....................................................................................69
Setting up DNSe (Digital Natural Sound engine) .......................................................70
Digital
Analog
Special Features .....................................................................................72
Setting the Function Help ........................................................................................72
Menu Transparency Level........................................................................................73
Using the V-Chip....................................................................................................74
Viewing Closed Captions (On-Screen Text Messages) ......................................84
Viewing Closed Captions (On-Screen Text Messages) ......................................86
Analog
Digital
Using the Guide ....................................................................................................88
Using Game Mode ................................................................................................90
Appendix..............................................................................................92
Replacing the Lamp................................................................................................92
Troubleshooting .....................................................................................................94
Cleaning and Maintaining Your TV ..........................................................................95
Using Your TV in Another Country ...........................................................................95
Specifications ........................................................................................................95
English - 5
SAMSUNG

Your New Wide TV

Your New Wide TV

Viewing Position

To optimize your viewing comfort, please follow the guidelines below for viewing distance. If viewing for an extended period of time, sit as far back from the screen as possible.
When installing the product, make sure to keep it away from the wall (more than 10 cm/4 inches) for ventilation purposes.
• Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.
English - 8

List of Features

Your TV was designed and engineered using the latest technology. It is a full-featured, high-performance unit that exceeds industry standards. In addition, it has these special features:
• Easy-to-operate remote control
• Easy-to-use on-screen menu system you can access from right side buttons or remote control
• Automatic timer to turn the TV on and off at any time you choose
• Adjustable picture and sound settings and the ability to memorize your favorite settings
• Automatic channel tuning for up to 181 channels
• A special filter to reduce or eliminate reception problems
• Fine tuning control for the sharpest picture possible
• A built-in multi-channel sound decoder for stereo and bilingual listening
• Built-in, dual channel speakers
• A special sleep timer
• Widescreen TV with adjustable image size
• Life-like clear images provided by DNle technology
• My Color Control Mode for corresponding with your color style
• Color weakness Mode
• Digital Input (HDMI/DVI IN) jack
• Digital Audio Output (OPTICAL) jack
• AV network system (Anynet) that enables you to easily control Samsung audio-video(AV) devices from this TV.

Checking Accessories

Once you have unpacked your TV, check to make sure that you have all the parts shown here. If any piece is missing or broken, call your dealer.
Owner’s Instructions
The following parts are sold separately and are available at most electronics stores.
S-VIDEO Cable
Optical Cable
Remote Control (BP59-00084B)/
AAA Batteries
HDMI Cable
Antenna Cable
Anynet Cable
(BN39-00518B)
Component Cables (RCA)HDMI/DVI cable
English - 9
Your New Wide TV

Right side buttons

The buttons on the right side panel control your TV’s basic features, including the on-screen menu system. To use the more advanced features, you must use the remote control.
Press to switch between viewing TV programs and signals from connected components. Press to see the on-screen menu.
Press to raise or lower the volume and to select items when using the on-screen menu.
Press to change channels and move between items on the on-screen menu.
Press to activate (or change) a particular item.

Side Panel Jacks

Use the right side panel jacks to connect a component that is used only occasionally (a camcorder or video game, for example).
Connect the video signal from a camcorder or video game.
Connect the audio signal from a camcorder or video game.
Connect an S-Video signal from a camcorder or video game. (S-Video 3 jack and Audio L/R input 3 are used in conjunction.)
English - 10

Front Panel LED Indicators

The three lights on the front panel indicate the status of your TV.
Indicator Light Key
: Light is On : Light is Blinking : Light is Off
POWER
Press to turn the TV on and off.
Remote Control Sensor
Aim the remote control towards this spot on the TV.
TIMER
LAMP STAND BY/TEMP Indication
Standby state.
The picture will automatically appear in about 15 seconds. Auto Timer ON/OFF has been set and the set will automatically be
turned on in about 25 seconds. A cooling fan inside the set is not operating normally.
Lamp cover on the rear of the set is not properly shut.
Check if the ventilation hole on the rear of the set is blocked, because if the inner temperature is too high, the power will shut off.
Lamp may be defective. Please contact a certified technician.
• It takes about 30 seconds for the TV to warm up, so normal brightness may not appear immediately.
• The TV has a fan to keep the inside lamp from overheating. You’ll occasionally hear it working.
English - 11
Your New Wide TV

Rear Panel Jacks

Use the rear panel jacks to connect components such as a VCR. You can connect different components such as VCRs, Set-Top Box and a DVD player etc., because there are two sets of video input jacks and two sets of component video input jacks on the rear panel of your TV. For more information, see “Connections”.
Œ
ANTENNA terminals
Two independent cables or antennas can be connected to these terminals. Use “ANT 1 IN (CABLE)” and “ANT 2 IN (AIR)” terminals to receive a signal from VHF/UHF antennas or your cable system. (Refer to pages 16~18)
´
SERVICE
This jack is for software upgrades.
ˇ
S-VIDEO INPUT jacks
Connects an S-Video signal from an S-VHS VCR or DVD player. (Refer to page 20)
¨
DVI (Digital Video Interface) AUDIO INPUT jacks
Connect to the digital audio output jacks of a device with DVI output. (Refer to page 22)
ˆ
VIDEO/AUDIO INPUT jacks
Connect video/audio signals from external sources, such as VCR or DVD players. (Refer to page 21)
Ø
VIDEO/AUDIO OUTPUT jacks
Sends video/audio signals from the TV to an external source, such as a VCR. These jacks are available only in RF, Video and S-Video modes.
English - 12
COMPONENT1, 2 jacks (Y, P
Use these jacks to connect the component video/audio signals from a DVD player or a Set-Top Box. (Refer to pages 21~22)
DIGITAL AUDIO OUT (OPTICAL) jack
Connect to a Digital Audio Component. (Refer to page 24)
Anynet
Please refer to the Anynet Owner’s Instruction. This jack is for connecting to other Samsung Anynet-enabled devices.
˝
HDMI (High Definition Multimedia Interface)/ DVI INPUT jack
Connect to the HDMI jack of a device with HDMI output. These inputs can also be used as a DVI connection with separate analog audio inputs. An optional HDMI/DVI cable will be necessary to make this connection. When using the optional HDMI/DVI adapter, the DVI analog audio inputs on your TV allow you to receive left and right audio from your DVI device. (Refer to pages 22~23)
B
, PR, AUDIO L/R)

Remote Control

You can use your remote control within a distance of 23 feet and an angle of 30 degrees from the left and right sides of the TV’s remote control receiver. You can also use your remote control to operate your VCR, Cable box, DVD player or some Samsung Set-top boxes. See pages 32~33 for details.
1. POWER
Turns the TV on and off.
2. P.MODE
Adjust the TV picture by selecting one of the preset factory settings (or select your personal, customized picture settings.)
3. ANTENNA
Press to select “AIR” or “CABLE”.
4. CHANNEL NUMBER
Press to directly tune to a particular channel.
5.
-
Press to select additional channels (digital and analog) being broadcast by the same station. For example, to select channel “54-3”, press “54”, then press “
6. VOL +, VOL
Press to increase or decrease the volume.
-
7. MUTE
Press to mute the TV sound.
8. Anynet
Runs the Anynet view functions and sets up Anynet devices. Please refer to the Anynet Owner’s Instruction.
9. MENU
Displays the main on-screen menu.
10. CH.LIST
Displays the channel list.
11. FAV.CH (Favorite Channel)
Press to switch between your favorite channels.
12. MODE
Selects a target device to be controlled by the Samsung remote control (i.e., TV, STB, VCR, CABLE, or DVD).
13. PRE-CH
Tunes to the previous channel.
14. SOURCE
Press to display all of the available video sources (i.e., TV, Set-Top Box, VCR, DVD, DTV).
15. CH /
Press to change channels. Moves from one set of screen information to the next in TV Guide menu.
-
” and “3”.
16. INFO
Press to display information on the TV screen.
17. EXIT
Press to exit the menu.
18. , , œ, , ENTER
Press to select highlight up, down, left, or right. While using the on-screen menus, press ENTER to activate (or change) a particular item.
19. MTS (Multichannel Television Stereo)
Press to choose Stereo, Mono or SAP (Secondary Audio Program).
20. STILL
Press to pause the current screen.
21. P.SIZE
Press to change the screen size.
22. DNSe
DNSe enhances the sound quality, automatically controls output, and prevents sound distortion. Press this button to set it On or Off.
23. DNIe (Digital Natural Image engine)
Activates DNIe Demo mode.
24. SET
Used during set up of this remote control, so that it will work compatibly with other devices (some Samsung Set-top boxes, VCR, Cable box, DVD, etc.)
25. SLEEP
Press to select a preset time interval for automatic shut off.
26. CAPTION
Controls the caption decoder.
27. VCR/DVD Controls
Controls VCR or DVD functions: Rewind, Stop, Play/Pause, Fast Forward.
28. RESET
If your remote control is not functioning properly, take out the batteries and press the reset button for about 2~3 seconds. Re-insert the batteries and try using the remote control again.
The blue button is only used during the channel list as an EXIT button.
English - 13
Your New Wide TV
Installing Batteries in the Remote Control
With normal use, the batteries in the remote control should last about a year. If you notice a performance degradation while using the remote, the batteries may need to be replaced. Make sure you replace both batteries and do not mix old and new batteries in the remote control. If you won’t be using the remote control for a long time, remove the batteries and store them in a cool dry place.
Slide the back cover all the way out to open the battery compartment of the remote control.
1
Install two AAA size batteries. Make sure to match the “+” and “–” ends of the batteries
2
with the diagram inside the compartment.
Slide the cover back into place.
3
NOTE
• Do not mix battery types, i.e, alkaline and manganese.
English - 14

Connections

Connections

Connecting VHF and UHF Antennas

If you do not have a cable system, you will need to connect an antenna to your TV.

Antennas with 75-ohm Round Leads

If your antenna looks like this: it has 75-ohm round leads.
Plug the antenna lead into the ANT 2 IN (AIR) on the
1
rear panel of your TV.
English - 16

Connecting Cable TV

You can connect different cable systems to your TV, including cable without a Cable box, and cable with a Cable box that descrambles some or all channels.

Cable without a Cable Box

Plug the incoming cable into the ANT 1 IN (CABLE) on the
1
rear panel of your TV.

Cable with a Cable Box that Descrambles All Channels

Find the cable connected to the ANTENNA OUT
1
terminal on your Cable box. This terminal might be labeled “ANT OUT”, “VHF OUT” or simply “OUT”.
Connect the other end of the cable to the “ANT 1 IN
2
(CABLE)” terminal on the rear panel of your TV.
English - 17
Connections

Cable with a Cable Box that Descrambles Some (But Not All) Channels

To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial cables (which you can buy from your Samsung dealer or any electronics store).
Find and disconnect the cable that is connected to
1
the ANTENNA IN terminal of your Splitter. This terminal might be labeled “ANT IN”, “VHF IN” or simply, “IN”. Connect this cable to a two-way splitter.
Connect a coaxial cable between an OUT terminal
2
of the splitter and the IN terminal of the Cable box.
Connect a coaxial cable between the ANTENNA OUT
3
terminal of the Cable box and the B-IN terminal of the RF (A/B) switch.
Connect a coaxial cable between the other OUT
4
terminal of the Cable box and the A-IN terminal of the RF (A/B) switch.
Connect the last coaxial cable between the OUT
5
terminal of the RF (A/B) switch and the ANT 1 IN (CABLE) on the TV.
After you’ve made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your Set-Top Box to the Cable box's output channel, which is usually channel 3 or 4.)
English - 18

Connecting a VCR

Connecting a VCR to the Video or S-Video/Audio jack

Connect the Video/Audio cables between the VIDEO
1
or S-VIDEO/AUDIO input jacks on the TV and VIDEO or S-VIDEO/AUDIO output jacks on the VCR.
NOTES
• For better video, use an S-Video cable.
• Please be sure to match the color coded input terminals and cable jacks.
Incoming Cable or Antenna
TV Rear Panel
or
Stereo VCR
English - 19
Connections

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a Camcorder to your TV. You can use your camcorder to view tapes without using a VCR.
Locate the A/V output jacks on the camcorder. They are
1
usually found on the side or back of the camcorder.
Connect a set of audio cables between the AUDIO
2
IN jacks on the TV and the AUDIO OUT jacks on the camcorder. If you have a mono Camcorder, connect L(mono) to the Camcorder audio out using only one audio cable.
Connect a video cable between the VIDEO IN (or
3
S-VIDEO IN) jack on the TV and the VIDEO OUT jack on the Camcorder. The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your Camcorder is stereo, you need to connect a set of two cables.
TV Rear of right side
1
Camcorder Output Jacks
or
Camcorder
3
2
English - 20

Connecting a DVD Player

The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
Connecting to Y, PB
Connect a set of audio cables between the
1
COMPONENT (1 or 2) AUDIO (L, R) IN jacks on the TV and the AUDIO OUT jacks on the DVD player.
To enable Component video viewing, connect a set of
2
video cables between the COMPONENT (1 or 2) VIDEO (Y, P on the TV and VIDEO
B/PR
(Y/P jacks on the DVD player.
, PR
B
, PR) IN jacks
or Y/CB/CR) OUT

Connecting to Audio and Video Jacks

Connect a set of audio cables between the AUDIO
1
IN (1 or 2) jacks on the TV and the AUDIO OUT jacks on the DVD player.
TV Rear Panel
Incoming Cable or Antenna
2
1
DVD Player
TV Rear Panel
Connect a video cable between the VIDEO IN (1
2
or 2) jack on the TV and the VIDEO OUT jack on the DVD player.
NOTE
•For an explanation of Component video, see your DVD player’s owner’s manual.
Incoming Cable or Antenna
2
DVD Player
1
English - 21
Connections

Connecting a DTV Set-Top Box

Connecting to Y, PB
Connect a set of audio cables between the
1
COMPONENT (1 or 2) AUDIO (L, R) IN jacks on the TV and the AUDIO OUT jacks on the Set-Top Box.
Connect a set of video cables between the
2
COMPONENT (1 or 2) VIDEO (Y, P on the TV and VIDEO
B/PR
(Y/P jacks on the Set-Top Box.
, PR
B
, PR) IN jacks
or Y/CB/CR) OUT

Connecting to DVI (Digital Visual Interface)

Connect a set of audio cables between the DVI
1
AUDIO (L, R) IN jacks on the TV and the AUDIO OUT jacks on the Set-Top Box.
Incoming Cable or Antenna
TV Rear Panel
TV Rear Panel
1
DTV Set-Top Box
2
Connect an HDMI/DVI video cable between the
2
HDMI/DVI IN jack on the TV and the DVI OUT jack on the Set-Top Box.
NOTES
•For an explanation of Component video, see your Set-Top Box owner’s manual.
• Requires a Cable Converter.
• Make sure the DVI source’s power is on, or you will be unable to select it in the
TV menu's source list.
English - 22
Incoming Cable or Antenna
2
DTV Set-Top Box
1

Connecting to HDMI (High Definition Multimedia Interface)

Connect an HDMI cable between the HDMI/DVI IN
1
jack on the TV and the HDMI OUT jack on the Set-Top Box.
NOTE
• Make sure the HDMI/DVI source’s power is on, or you will be unable to select it in the TV menu’s source list.
Incoming Cable or Antenna
TV Rear Panel
DTV Set-Top Box
English - 23
Connections

Connecting a Digital Audio System

There are many types of digital audio systems on the market today. A simplified illustration of an audio system is shown below. For more information, see your audio system owner’s manual.
If your audio system has an optical digital audio input,
1
connect to the “DIGITAL AUDIO OUT (OPTICAL)” jack on the TV.
NOTE
• OPTICAL: converts the electric signal into an optical light signal, and transmits it through glass fibers. See page 67 to set the digital output format (Dolby Digital or PCM) appropriate to your digital audio component.

Connecting to an Analog Amplifier

The “AUDIO OUT” terminals cannot be used for external
1
speakers. You must hook them up to an amplifier. When an audio amplifier is connected to the “AUDIO OUT” terminals: Decrease the gain (volume) of the audio amplifier, set the internal mute on in the TV’s Sound Menu and adjust the volume level with the volume control of the amplifier.
TV Rear Panel
Audio System
TV Rear Panel
NOTE
• If using the HDMI or Component input on the TV, the audio output signal is available only when the TV’s Internal Mute is set to on. (Refer to page 68)
English - 24
Amplifier

Operation

Operation

Turning the TV On and Off

Press the POWER button on the remote control. You can also use the POWER button on the front panel.

Viewing the Menus and On-Screen Displays

The on-screen menu system allows you to control the settings of your TV. Access the on-screen menu system by pressing the MENU button on the remote control. Once the on-screen menu appears, use the …/†/œ/√/ENTER buttons on your remote control to select menu items and make adjustments. You can also view the on-screen menu system and make some adjustments using the TV’s side panel buttons.
Viewing the Menus
Press the MENU button. The main menu is displayed.
1
There are six menu groups: “Input”, “Picture”, “Sound”, “Channel”, “Setup”, and “Guide”.
Press the … or † button to select an item you want
2
in the menu. Press the œ, √ or ENTER button to display, change, or use the selected items. Use the ENTER button to enter items in the menu.
Press the EXIT button to exit.
3
Viewing the Display
Press the INFO button on the remote control. The TV displays the current channel, the status of certain picture and sound settings and the current time. The information displayed varies according to the selected source.
Input
Source List : TV Edit Name
Picture
Anynet
Sound
Channel
Setup
Guide
Input
Mode : Standard Size : 16:9
Picture
Digital NR : On DNIe Demo : Off
Sound
My Color Control
Channel
Film Mode : Off
Setup
Guide
Cable 3
Picture Mode Sound Mode MTS Caption V-Chip
No Time Information
Input
Move
Move Enter Return
Picture
Standard Custom Stereo Off Off
Enter
Exit
√ √
√ √ √ √ √ √
English - 26

Selecting a Menu Language

Press the MENU button. Press the … or † button to
1
select “Setup”, then press the ENTER button.
Press the ENTER button to select “Language”.
2
Press the … or † button to select “English”, “Español” or “Français”, then press the ENTER button.
Press the EXIT button to exit.
Input
Language : English Time
Picture
V-Chip Caption
Sound
Menu Transparency
Channel
Blue Screen : Off Color Weakness
Setup
Function Help
Guide
Input
Language : English
Time
Picture
V-Chip Caption
Sound
Menu Transparency
Channel
Blue Screen : Off Color Weakness
Setup
Function Help
Guide
Setup
: Medium
: Off
Move Enter Return
Setup
English
Español Français
: Medium
: Off
Move Enter Return
√ √ √ √ √ √ √ √
English - 27
Operation

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the CH and CH buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).
Selecting the Video Signal Source
Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna or cable system).
Press the MENU button. Press the … or † button to
1
select “Channel”, then press the ENTER button.
Press the ENTER button to select “Antenna”.
2
Press the … or † button to select “Air” or “Cable”, then press the ENTER button.
Press the … or † button to select “Auto Program”, then
3
press the ENTER button.
Input
Antenna : Air Auto Program
Picture
Add/Delete Favorite Channels
Sound
Name
Channel
Fine Tune
Signal Strength
Setup
LNA : On
Guide
Input
Antenna : Cable
Auto Program
Picture
Add/Delete Favorite Channels
Sound
Name
Channel
Fine Tune
Signal Strength
Setup
LNA : Off
Guide
Input
Antenna : Air Auto Program
Picture
Add/Delete Favorite Channels
Sound
Name
Channel
Fine Tune
Signal Strength
Setup
LNA : On
Guide
Channel
Move Enter
Channel
Move Enter Return
Channel
Move
Air
Cable
Enter
Return
Return
√ √ √ √ √ √
√ √ √ √ √ √
English - 28
NOTE
• All available DTV and analog channels are automatically stored in memory.
Press the … or † button to select the Antenna connection, then press the
4
ENTER button.
• Air : “Air” antenna signal Cable : “Cable” antenna signal Air+Cable : “Air” and “Cable”
antenna signals
Input
Select the antennas to memorize.
Picture
Air
Cable
Sound
Air+Cable
Channel
Setup
Guide
Auto Program
Start
Start
Start
Move Enter Return
When selecting Cable TV system: Press the ENTER button to start the auto program. By default, the cable TV system is set to “STD”. If you want to select another type of cable system, press the œ button and use the … or † button to select Analog or Digital “STD”, “HRC” or
Input
Picture
Sound
Channel
Setup
Guide
“IRC”. Press the ENTER button.
• STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected.
Press the button to select “Start”, then press the ENTER button to start the auto
5
program. The TV begins memorizing all available stations. Press the ENTER button at any time to interrupt the memorization process.
Input
Picture
Sound
Channel
Setup
Guide
Press the EXIT button to exit.
• The TV must be connected to an
Auto Program in progress
antenna in order to receive digital TV signals. Even if a particular channel is deleted from the memory, you can always tune to that channel directly by using the number buttons on the remote control.
Auto Program
Select the cable system. Analog
STD
HRC IRC
Digital
STD
HRC IRC
Move
Select the cable system. Analog
STD
HRC IRC
Digital
STD
HRC IRC
Auto Program
Enter
Auto Program
Move Enter Return
Cable Channel 26
Stop
Enter Return
Start
Return
Start
English - 29
Loading...
+ 67 hidden pages