Samsung DW80J3020UW/AA, DW80J3020US/AA, DW80J3020UB/AA, DW80F800UWS/AA, DW80F600UTW/AA Installation Guide

...

Dishwasher

installation guide

DMT800 Series DMT610 Series DMT400 Series DMT350 Series

DW7933 Series DW80F800 Series DW80F600 Series

DW80J3020 Series

STOP

These installation instructions are intended for use by qualiﬁ ed installers.

If you are having problems installing this dishwasher Please call : 1-800-SAMSUNG (726-7864)

for assistance : www.samsung.com

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service, please register your product at

www.samsung.com/register

safety instructions

Throughout this manual, you’ll see Warning and Caution notes. These warnings, cautions, and the important safety instructions that follow do not cover all possible conditions and situations that may occur. It’s your responsibility to use common sense, caution, and care when installing, maintaining, and operating the dishwasher. Samsung is not liable for damages resulting from improper use.

IMPORTANT SAFETY INSTRUCTIONS

What the icons and signs in this installation guide mean:

Hazards or unsafe practices that may result in severe personal injury or

WARNING

CAUTION

These warning signs are here to prevent injury to you and others. Please follow them explicitly. After reading this section, keep it in a safe place for future reference.

Read all instructions before using the appliance.

Install and store the dishwasher inside, away from exposure to weather.

Do not install the dishwasher near electrical components. Keep the dishwasher away from open ﬂ ames.

CAUTION

Do NOT install the dishwasher on a carpet as this is a ﬁ re hazard.

Do NOT install the dishwasher in a location where the water may freeze (where the temperature falls below 32 ˚F (0 ˚C)). Frozen water in the hoses or pipes may damage the dishwasher.

As with all any equipment using electricity, water and moving parts, potential hazards exist. To safely operate this appliance, become familiar with its operation and exercise care when using it.

The dishwasher must be properly grounded. Never connect it to an ungrounded outlet.

Prior to removal of original dishwasher and the installation of your new unit, make sure to switch o your circuit breaker. Do not connect the dishwasher until you have completed the installation. Connecting the power cable is the last step when installing the dishwasher.

All wiring and grounding must be done in accordance with the electrical code applicable to the region.

death.

Hazards or unsafe practices that may result in personal injury or property damage.

To reduce the risk of ﬁ re, explosion, electric shock, or personal injury when using the dishwasher, follow these basic safety precautions:

Follow directions explicitly.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

2_ safety instructions

GROUNDING INSTRUCTIONS

For a permanently connected appliance:

This appliance must be connected to grounded metal, a permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.

The dishwasher is very heavy. Do not attempt to move or carry a dishwasher alone. Two or more people are needed to move a dishwasher and avoid potential injuries.

If the power cable is damaged, it must be replaced by the manufacturer, a service agent or

CAUTION

similarly qualiﬁ ed person in order to avoid a hazard.

Do not touch the power cable with wet hands.

CAUTION

Do not connect another appliance to the same power outlet as the dishwasher.

CAUTION

Make sure to use a new water supply line. Old lines are susceptible to breakage because they become hardened and may cause property damage due to a water leakage.

The dishwasher must be connected to a hot water supply with a temperature between 120 ˚F (49 ˚C) ~ 149 °F (65 ˚C). This temperature range provides the best washing result and shortest cycle time. Temperature should not exceed 149 ˚F (65 ˚C) to prevent damage to dishes.

Ensure that the water supplied to the dishwasher does not freeze. Frozen water can damage the hoses, valves, pump, or other components.

Certiﬁ ed residential dishwashers are not intended for licensed food establishments. (NSF/ANSI Standard 184 for Residential Dishwashers)

For a full list of safety information, please refer to the User Manual.

BEFORE INSTALLING THE DISHWASHER

WARNING

Tip-Over Hazard

- Do not use the dishwasher until it is correctly installed.

- Do not push down on the door when it is open.

- Do not place excessive weight on the open door.

Electric Shock Hazard

Failure to follow these instructions can result in death, ﬁ re, or electric shock:

- Electrically ground the dishwasher

- Connect the ground wire to the green ground connector in the junction box.

- Do not use an extension cord.

To reduce the risk of electric shock, ﬁ re, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation.

safety instructions _3

contents

PREPARING THE DISHWASHER

ENCLOSURE

INSTALLING THE DISHWASHER

SPECIFICATIONS

5 Product dimensions 5 Enclosure dimensions

6 STEP 1 Check the parts and tools 8 STEP 2 Select the best location for the

dishwasher

9 STEP 3 Check water supply requirements

and cautions

10 STEP 4 Check the electrical requirements

and cautions

11 STEP 5 Unpacking and inspecting the

dishwasher

13 STEP 6 Preparing the dishwasher 14 STEP 7 Placing the dishwasher and

connecting the HOT WATER supply line

15 STEP 8 Leveling the dishwasher 16 STEP 9 Securing the dishwasher 18 STEP 10 Connecting the drain hose 20 STEP 11 Wiring connections 21 STEP 12 Completing the installation

22 Speciﬁ cations

4_ contents

preparing the dishwasher enclosure

PRODUCT DIMENSIONS

Side view

(DMT800 series/ DMT610 series/ DMT400 series/ DW80F800 series/ DW80F600 series)

Side view

(DMT350 series / DW7933 series / DW80J3020 series)

27” (686 mm)

20 ½ ” (520 mm)

24 ²⁄3” (627mm)

Rear view

5” (128mm)

2 1⁄3” (60mm)

⁄8” (605 mm)

The water supply line, power cable and drain hose should go through this space behind the dishwasher. Then, they run in channels under the dishwasher to connections in the front.

⁄

” (860mm)

01 PREPARING THE DISHWASHER

20 ½ ” (520 mm)

24 ²⁄3” (627mm)

ENCLOSURE DIMENSIONS

This dishwasher is designed to be enclosed on the top and on both sides by a standard residential kitchen cabinet unit.

The installation enclosure must be clean and free of any obstructions.

The enclosure must be at least 24 inches wide, 24 inches deep, and 34 1/8 inches high.

For the front door of the dishwasher to be ﬂ ush with the leading edge of the counter top, the counter top must be at least 25 inches deep.

24” (610 mm)

minimum

24” (610 mm)

minimum

preparing the dishwasher enclosure _5

34 1⁄

” (867 mm)

installing the dishwasher

Be sure that you or your installer follow these instructions closely so that the new dishwasher works properly and that you’re not at risk of injury when washing dishes.

STEP 1 CHECK THE PARTS AND TOOLS

Before starting on the installation, prepare all the necessary tools and parts required to install the dishwasher. This will save installation time and simplify the installation process.

Parts required

Provided with the dishwasher. Check when you unbox the dishwasher in Step 5.

2 Installation Brackets

Kick Plate

2 Flat Head Screws

(For the installation

bracket)

2 Leg support

(for DW80F800 /

DW80F600 series)

2 Screws

(for the side walls)

2 Screws

(for the kick plate)

Not provided

Power cable

Hot water supply line

Hose clamp Air gap Rubber connector

For the hot water supply line – We strongly recommend using 3/8” minimum O.D. copper tubing with a compression ﬁ tting or a ﬂ exible stainless steel braided hot water supply line. [Warning: Do not use plastic tubing. Plastic tubing can deteriorate over time and cause a leak inside the tube ﬁ tting.] You also need a 90° elbow with your hot water supply line (copper tubing/compression ﬁ tting or braided hose) on the other.

For the power cable, we recommend a jacketed 12-2 cable with ground. Note that some local codes may require the cable to have a BX style metal jacket.

Twist on wire

connector

90° Elbow(

”)

/8” N.P.T. external pipe threads on one end and a ﬁ tting sized to ﬁ t

Strain relief

Tube ﬁ ttings

Electrical tape &

Standard duct tape

tape or sealing

Teﬂ on

compound

6_ installing the dishwasher

Tools required

Electric drill Safety glasses Gloves Flashlight

Adjustable wrench Wire stripper Pliers Nipper

Tape measure Pencil Phillips screwdriver Flat screwdriver

Tubing cutter Cutting knife Hole saw Level

Torx t20 Hex L-wrench

02 INSTALLING THE DISHWASHER

installing the dishwasher _7

installing the dishwasher

New installation

If the dishwasher is a new installation, most of the installation work must be done before the dishwasher is moved into place.

Replacement

If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher connections for compatibility with the new dishwasher. Repace the existing connections as necessary.

STEP 2 SELECT THE BEST LOCATION FOR THE DISHWASHER

The following criteria are important to ensure the best location for the dishwasher:

- The location must have a solid ﬂ oor that is able to support the weight of the dishwasher.

- The location must be near a sink with easy access to the water supply, drain, and electrical

outlet.

For the drain to operate properly, the dishwasher should be installed within 9.8 ft (3 m) of the sink.

- The location must let you load your dishes into the dishwasher easily.

- The location must have su cient space for the dishwasher door to open easily and provide

enough space between the dishwasher and the cabinet sides (at least 0.1 in (2 mm)).

If the dishwasher is installed in a corner, ensure that the side of the dishwasher is more than 2 in. (50 mm) from the wall or cabinet to its right or left.

- The wall at the back must be free of obstructions.

If this is a new installation, follow these steps:

1. Using a 2 ½ inch hole saw, cut a hole into the side of the cabinet that holds the sink as

shown in Figure 1 below.

2. If the base inside the sink cabinet is raised above the kitchen ﬂ oor and is higher than the

connections on the dishwasher, make a hole in the base inside the cabinet and in the cabinet side as shown in Figure 1-2.

Depending on where your electrical outlet is, you may need to cut a hole in the opposite cabinet side.

The hole for the water supply line, drain hose and power cables.

8_ installing the dishwasher

STEP 3 CHECK WATER SUPPLY REQUIREMENTS AND CAUTIONS

• The hot water supply line pressure must be between 20~120 psi (140~830 kPa).

• Adjust the water heater to deliver water between 120 ˚F (49 ˚C) ~ 149 ˚F (65 ˚C).

- The dishwasher must be connected to a hot water supply between 120 ˚F (49 ˚C) ~ 149 ˚F

(65 ˚C). This temperature range provides the best washing result and shortest cycle time. Temperature should not exceed 149 ˚F (65 ˚C) to prevent damage to dishes.

- Ensure that the water supply valve is turned o before connecting the hot water supply line to

the dishwasher.

- Seal the hot water supply line connections using teﬂ on tape or sealing compound to stop any

water leakage.

- The hot water supply line must pass through the channel on the bottom of the dishwasher as

shown in Figure 2. Do not place the dishwasher on the water supply line.

- The drain hose connected to the dishwasher must be run through the hole in the side wall so

it can be connected to the drain outlet of the sink. When you install the dishwasher, ensure there is nothing on the drain hose and be careful not to tear it during the installation process.

Power cable

Hot Water Supply Line

3~7¹⁄3 in.

5¹⁄ (135 ~ 185mm)

Dishwasher bottom

02 INSTALLING THE DISHWASHER

installing the dishwasher _9

installing the dishwasher

STEP 4 CHECK THE ELECTRICAL REQUIREMENTS AND CAUTIONS

The electrical requirements for the dishwasher are as follows:

• In the United States, install in accordance with the National Electric Code/State and Municipal codes

and/or local codes.

• In Canada, install in accordance with the Canadian Electric Code C22.1-latest edition/Provincial and

Municipal codes and/or local codes.

• For cable direct connections.

- Use ﬂ exible, armored or non-metallic sheathed, copper wire with a grounding wire that meets the wiring requirements for your local codes and ordinances.

- Use the strain relief method provided with the wiring junction box or install a U.L.-listed/CSA-certiﬁ ed clamp connector to the wiring junction box. If using conduit, use a U.L.-listed/CSA-certiﬁ ed conduit connector.

• For power cord connections

- The power supply cord must plug into a mating three prong, grounded outlet, located in the cabinet next to the dishwasher opening. The outlet must meet your local codes and ordinances. Use a U.L.listed/CSA-certiﬁ ed power cord kit.

- The dishwasher must be connected to an electrical supply that provides the voltage and

amperage marked on the rating plate of the unit: 15 amps, 120 volts, 60Hz AC.

- Ensure that the circuit breaker connected to the dishwasher is o .

- The power cable must not extend more than 4 ft (1.2 m) from the side of the dishwasher.

- Check with a qualiﬁ ed electrician or serviceman if you are unsure whether the dishwasher is

properly connected.

- Do not connect another appliance to the same power outlet as the dishwasher.

- Before connecting the power cable to the dishwasher, ensure that there are no electrical

hazards (which may result in ﬁ re, explosion, electric shock, or personal injury).

- The power cable must pass through the channel on the bottom of the dishwasher as shown

in Figure 3.

Hot Water Supply Line

10_ installing the dishwasher

Power cable

5¹⁄

3~7¹⁄3 in.

(135 ~ 185mm)

Dishwasher bottom

STEP 5 UNPACKING AND INSPECTING THE DISHWASHER

Unbox the dishwasher in an open area free of obstruction both around the carton and overhead. We recommend that you retain the carton and all of the packing materials until the dishwasher is fully installed and operational to ensure you have removed all the product’s components from the carton prior to disposal.

Unboxing

1. Position the carton right-side-up with top arrows pointing upwards.

2. Unbuckle or cut the four straps securing the carton top.

3. Lift the top of the telescoping carton clear of the carton tray and the contents, and then turn

it over and place it on the ﬂ oor.

4. Put the straps and all of the packing materials from around the dishwasher inside the carton

top, inspecting them for any signs of damage.

5. Locate and set aside the dishwasher's kick plate. The Kick plate is attached to packing

material of the dishwasher.

Kick plate

6. Lift the dishwasher from the carton tray, and then place it on the ﬂ oor.

Put the tray into the carton top.

7. Remove the bag that protects the dishwasher during shipping.

ALWAYS LIFT THE Dishwasher TO MOVE IT. Sliding it over rough surfaces can damage the

CAUTION

dishwasher’s feet and sliding the feet over ﬁ nished surfaces can, in some cases, damage that ﬁ nish or the underlying surface.

8. There is also packing inside the dishwasher that you may want to leave in place until the

dishwasher is installed.

9. DO NOT, under any circumstances, remove the sound-absorbent padding that surrounds

the exterior of the tub of the dishwasher.

Inspecting

Mechanical

1. Check the plastic base assembly to ensure that it is intact

2. Check the dishwasher’s feet to ensure they are in place and can be adjusted so you can level

and secure the dishwasher.

3. Check all the visible components on the bottom of the dishwasher to ensure they are intact

and secure.

4. Check the door latch, the operation of the hinges, and conﬁ rm the door is properly secured

to the dishwasher.

02 INSTALLING THE DISHWASHER

installing the dishwasher _11

installing the dishwasher

Plumbing

1. Check the hot water connection on the front left-side of the base of the dishwasher.

The mounting plate should be secured to the front of the base, the threads inside the connection should be smooth and shiny, and the area should be clean and free of any debris.

2. Check the plastic Brake and Sensor cases to ensure these assemblies are not cracked and

that all connections are secure.

3. Check the drain hose for any holes or deformities that could allow a water leak during

draining.

Electrical

1. Conﬁ rm the junction box cover is secured to the junction box on the front right-side of the

base of the dishwasher.

2. Conﬁ rm the electrical box was not damaged during shipping and that it is secured to the

base of the dishwasher.

Appearance

1. Conﬁ rm there are no dents or scratches on the front of the dishwasher.

2. Check the edges of the doors for any roughness or cracking

3. Check the control panel to ensure it is clear and unscratched, and that all the control markers

are in their proper places.

Parts

1. Conﬁ rm you have all the parts listed in Step 1 on page 6.

12_ installing the dishwasher

STEP 6 PREPARING THE DISHWASHER

1. Ensure that the circuit breaker and water supply valve are turned o before proceeding with

the following steps.

Before you move or lay down the dishwasher for installation, make sure to adjust the height of the legs so the legs are as short as possible. This prevents the legs from breaking.

CAUTION

Level the dishwasher by adjusting the height of the legs after you have the dishwasher in place.

2. Wrap Teﬂ on tape around the threads of the 90˚ elbow, and then attach the elbow to the

Inlet valve (Figure 4 - B). Tighten until the elbow is tight and pointing towards the water hose channel in the base of the dishwasher (about 4 o'clock). To prevent the inlet valve from being blocked, make sure that the Teﬂ on tape does not enter the valve. Do not over tighten.

3. Cut the strings securing the drain hose to the back of the dishwasher. Roll-out the hose.

Make sure there are no kinks and that the hose is not bent at any extreme angles that could constrict the ﬂ ow of water.

4. Remove the junction box cover located at the bottom front right of the dishwasher using a

screwdriver, and then Install the strain relief (Figure 4 - C). Make sure to keep the junction box cover you removed. It is used in Step 10, Wiring Connections.

5. If the countertop is made of wood or a material that is not damaged by drilling, attach the

two (2) Installation brackets that were supplied with the dishwasher using the supplied screws (Figure 4 - A). They will be used in Step 8, Securing the Dishwasher.

6. For DW80F800, DW80F600, DW80J3020 series, install the leg supports at the bottom rear

left and right of the dishwasher (Figure 4 - D).

02 INSTALLING THE DISHWASHER

CAUTION

Do not overtighten the 90˚ elbow. Doing so may damage the water inlet valve and cause a water leak

Junction box

Strain relief

installing the dishwasher _13

installing the dishwasher

STEP 7 PLACING THE DISHWASHER AND CONNECTING THE HOT

WATER SUPPLY LINE

1. Adjust the three leveling legs at the bottom of the dishwasher after measuring the height

of the cabinet opening from under the countertop to the ﬂ oor. (See Step 7, Leveling the Dishwasher.)

2. Locate the hot water supply line and the power cable.

3. Place the dishwasher so that the hot water supply line is in the left channel and the power

cable is in the right channel of the base of the dishwasher. Use standard duct tape or cable ties to secure the water line and electrical cable to their adjacent channels in the base. This can prevent the the water line and electrical cable from being squeezed when you push the the dishwasher into place.

4. Pull the drain hose through the hole in the sink cabinet side wall. Keep it free of kinks.

5. Make sure the hot water supply line is not twisted, and then connect the hot water supply

line to the elbow joint.

6. Slide the dishwasher carefully into the installation space. If possible, gently pull any excess

lengths of water supply line, drain hose, or power cable back as you move the dishwasher. Get a second or third person to help you do this if necessary.

Do not place the dishwasher on the water supply line, drain hose, or power cable. Also, make sure they are not folded or twisted.

CAUTION

Drain hoseDrain hose

14_ installing the dishwasher

Power cablePower cable

Hot Water Supply LineHot Water Supply Line

Elbow( ³/8” (9.5mm))Elbow( ³/8” (9.5mm))

Inlet valveInlet valve

CAUTION

Do not overtighten the 90˚ elbow. Doing so may damage the water inlet valve and cause a water leak

STEP 8 LEVELING THE DISHWASHER

1. Open the door and place the level against the top of the

tub on the inside and check if the the dishwasher is level. If it is not level, rotate the leveling legs at the bottom front of the dishwasher until the dishwasher is level. See the ﬁ rst note below for instructions on adusting the height of the front legs.

2. Use the level to check if the dishwasher is level front to

back, as shown in the ﬁ gure to the right. If the dishwasher is not level front to back, adjust the height of the rear leg until the dishwasher is level. See the second note below for instructions on adusting the the rear leg.

3. Open the door of the dishwasher and

check if both the tub and door clearances are correct. If not, rotate the leveling legs on the bottom front of the dishwasher. You can aslo check this by placing a level against an inside front vertical surface of the tub.

If the leveling legs are rotated to the right (counter clockwise), they are loosened and the front of the dishwasher is raised. If they are rotated to the left (clockwise), they are tightened and the front of the dishwasher is lowered.

02 INSTALLING THE DISHWASHER

To adjust the height of a rear leg, turn the Hexbolt (at the front of the base) to the left to raise the back of the dishwasher using the proper tool (Hex L-wrench or similar tool).

Before you move the dishwasher for installation, make sure to adjust the height of the legs so the legs are as short as possible. This prevents the legs from breaking.

CAUTION

Level the dishwasher by adjusting the height of the legs after you have the dishwasher in place.

installing the dishwasher _15

installing the dishwasher

STEP 9 SECURING THE DISHWASHER

You must ﬁ x the dishwasher to the countertop or cabinet side walls for additional stability and safety.

1. If the countertop is made of wood or the material will not be damaged by drilling, follow the instructions in 2-1 below. If the countertop is made of granite, marble, or any other material that can be damaged by drilling, follow the instructions in 2-2 below.

2-1. If the installation brackets on the front of the dishwasher extend cut them down using a

nipper as shown in Figure 8 on the next page. Put a large towel into the bottom of the dishwasher to prevent wood shavings or a dropped screw from falling into the dishwasher. Carefully drill screw holes into the counter top bottom by passing the drill bit through a screw hole in each bracket, and then drilling into the counter top bottom beneath. Make sure the hole you drill is smaller than the diameter of the screw. Insert the provided screws into the brackets, and then tighten to secure the dishwasher to the counter top.

2-2. Put a large towel into the bottom of the dishwasher to prevent wood shavings or a

dropped screw from falling into the dishwasher. Remove the tub spacer caps with the tip of a screwdriver. The caps are just inside the tub near the top of the tub on both sides (Figure 9 on the next page). Drill a hole into the sides of the kitchen cabinet on both sides by carefully passing a drill bit through the screw holes exposed by the removal of the spacer caps, and then drilling into the cabinet side beneath. Make sure the hole you drill is smaller than the diameter of the screw. Also make sure the drill bit does not strike the sides of the spacer cap holes. Insert the provided screws into the holes, and then tighten to secure the dishwasher to the cabinet. Make sure the tub is not distorted by pressure from the screws. If the tub is distorted, loosen the screws a little. Replace the tub spacer caps.

• The screws or tub spacer cap may fall into the dishwasher while you are working with the door open. Cover the interior of the dishwasher with a towel to prevent any screws from falling into the dishwasher. If any foreign items such as a screw get into the dishwasher, it may cause noise, an abnormal operation, damage, or a malfunction.

• Use a magnetic screwdriver to help prevent screws from falling into the dishwasher.

• If a foreign item such as a screw gets into the dishwasher and you are unable to remove it, the dishwasher needs to be disassembled. Contact a qualiﬁ ed service technician for this.

16_ installing the dishwasher

02 INSTALLING THE DISHWASHER

Screw to countertop

Tub spacer cap

Screw to side wall

installing the dishwasher _17

installing the dishwasher

STEP 10 CONNECTING THE DRAIN HOSE

1. Check the parts on the sink to which the drain hose will be connected.

2. There are several ways to insert the drain hose into the drain hose connector of the sink,

as shown in the following ﬁ gures. You must connect the drain hose in accordance with the water pipe installation regulations in your region.

Case 1. Without disposal

Without disposal With an air gap/without disposal Without an air gap

Air gap

Drain hose

Hose clamp

Case 2. With disposal

With disposal Disposal with an air gap Without an air gap

Air gap

Hose clamp

18_ installing the dishwasher

Drain hose

Hose clamp

3. Check the size of the sink’s drain hose connector. If needed, cut the drain hose so its end

ﬁ ts onto the sink connector (½ in., ¾ in. or 1 in. - as shown in Figure 11 below). If the end of the drain hose does not ﬁ t onto the drain hose connector of the sink, use an adaptor purchasable at a plumbing/hardware supply store.

4. Slide a hose clamp over the end of the drain hose. Attach the drain hose to the sink

connector, slide the hose clamp to the end of the hose, and then tighten the hose clamp. Note : You must use a hose clamp. Failure to do so may cause water leakage.

5 . If there is no air gap, make sure to hang. the middle of the drain hose well above the sink

cabinet base to prevent backﬂ ow (see Figure 12 below).

Be careful when cutting o the end of the drain hose as there is a risk of injury. Clean around the sink’s drain connection so that it does not damage the hose. Check for any

CAUTION

foreign items in the drain hose and remove them.

02 INSTALLING THE DISHWASHER

Sink

Min. 20 in.

(508 mm)

Min. 30 in.

(762 mm)

Drain hose

1 in.

(25 mm)

¾ in.

(19 mm)

½ in.

(13 mm)

If required, cut o the end of the drain hose at one of the dotted lines.

Dishwasher

installing the dishwasher _19

installing the dishwasher

STEP 11 WIRING CONNECTIONS

1. Before connecting the power cable to the dishwasher, make sure the circuit breaker is o .

2. In the junction box located at the front bottom right of the dishwasher, ﬁ nd the three power

wires from the dishwasher including the grounding line.

3. Pass the power cable through the strain relief, and then into the junction box (Figure 13).

4. Connect the black wire of the dishwasher to the black wire of the power cable by insertng

both into a wire nut. and then rotating the wire connector as shown in Figure 14. Connect the white wire to the white wire and the green to the green in the same manner.

5. Recheck each wire to ensure it is connected correctly and securely.

Each colored wire should be connected to the corresponding wire of the same color. White should be connected to white, black to black, and green to green.

6. Replace the junction box cover on the dishwasher.

Black to black

Power cable

Junction box

Strain relief

White to white

Green to green (Ground to ground)

20_ installing the dishwasher

STEP 12 COMPLETING THE INSTALLATION

1. Open the door and remove all foam, paper packaging, and unnecessary parts.

2. Turn on the circuit breaker you turned o before you began the installation.

3. Open the water supply valve to supply water to the dishwasher.

4. Turn on the dishwasher, and then select and run a cycle.

Check if the power turns on correctly and if there is any water leakage while the dishwasher is operating. If no errors occur while it is operating, turn o the dishwasher, and then go to Step 5 below. If an error has occurred, turn o the dishwasher, close the water supply valve, and then refer to the user manual or contact a service center 1-800-SAMSUNG (726-7864).

Make sure to check for water leakage on both ends of the water supply line and drain hose

CAUTION

connector.

5. Conﬁ rm that the kick plate gasket is on the bottom of the kick plate. To install the kick plate,

refer to the ﬁ gure below.

02 INSTALLING THE DISHWASHER

installing the dishwasher _21

speciﬁ cations

Power supply 120 V, 60 Hz AC only

Water pressure 20 ~ 120 psi (140 ~ 830 kPa) Dimensions

(Width×Depth×Height) Nominal inlet water temperature 120 ˚F (49 ˚C)

Speciﬁ cations are subject to change without notice for quality improvement purposes. The actual appearance of the dishwasher may di er from the illustrations in this manual.

⁄8 x 24¾ x 337⁄8 in. (605 x 627 x 860 mm)

22_ speciﬁ cations

+ 50 hidden pages