Samsung DVG41A3000W, DVE41A3000W User Manual

Dryer

User manual

DVE(G)41A3000*

DV3000A(SEM)_DC68-03784P-00_EN.indd 1			2020-12-07 4:50:47

Contents

Safety information

		What you need to know about the safety instructions
		Important safety symbols
	<![if ! IE]> <![endif]>Contents	CALIFORNIA PROPOSITION 65 WARNING
		Important safety precautions
		Warnings
		Cautions

Installation requirements

Key installation requirements

Location considerations

Ducting requirements

Mobile home installation

Exhausting requirements

Gas requirements

Electrical requirements

Installation

What’s included

Step-by-step installation

Vent blockage test

Exhaust ducting guide

Switching the door position

Before you start

Sort and load

Functional prerequisite

Operations

Control panel

Simple steps to start

Cycle overview

Cycle chart

Cycle guide

Special features

2  English

4

4

4

8

8

9

10

12

12

12

15

16

17

18

19

22

22

24

28

32

32

35

35

35

36

36

37

38

39

41

42

DV3000A(SEM)_DC68-03784P-00_EN.indd 2			2020-12-07 4:50:47

Maintenance

Cleaning

Troubleshooting

Checkpoints

Information codes

Specifications

Fabric care chart Protecting the environment Specification sheet

43

43

44

44

48

49

49

50

51

English  3 

<![if ! IE]>

<![endif]>Contents

DV3000A(SEM)_DC68-03784P-00_EN.indd 3			2020-12-07 4:50:47

<![if ! IE]>

<![endif]>information Safety

Safety information

Congratulations on your new Samsung dryer. This manual contains important information on the installation, use and care of your appliance. Please take some time to read this manual to take full advantage of your dryer’s many benefits and features.

What you need to know about the safety instructions

Please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance. Please store the manual in a safe location close to the appliance for future reference. Use this appliance only for its intended purpose as described in this instruction manual.

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution and care when installing, maintaining and operating your dryer.

Because the following operating instructions cover various models, the characteristics of your dryer may differ slightly from those described in this manual and not all warning signs may be applicable. If you have any questions or concerns, contact your nearest service center or find help and information online at www.samsung.com.

Important safety symbols

What the icons and signs in this user manual mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury, death and/or property damage.

CAUTION

Hazards or unsafe practices that may result in personal injury and/or property damage.

NOTE

Indicates that a risk of personal injury or material damage exists.

These warning signs are here to prevent injury to yourself and others. Please follow them explicitly.

After reading this manual, store it in a safe place for future reference.

Read all instructions before using the appliance.

As with any equipment that uses electricity and moving parts, potential hazards exist. To safely operate this appliance, familiarize yourself with its operation and exercise care when using it.

SAVE THESE INSTRUCTIONS

4  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 4			2020-12-07 4:50:48

WARNING - Risk of Fire

•Clothes dryer installation must be performed by a qualified installer.

•Install the clothes dryer according to the manufacturer’s instructions and local codes.

•Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance

manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.

•Do not install a booster fan in the exhaust duct.

•To reduce the risk of severe injury or death, follow all installation instructions.

•Save these instructions.

<![if ! IE]>

<![endif]>information Safety

SAVE THESE INSTRUCTIONS

English  5 

DV3000A(SEM)_DC68-03784P-00_EN.indd 5			2020-12-07 4:50:48

Safety information

<![if ! IE]>

<![endif]>information Safety

WARNING - To reduce the risk of fire or explosion:

•Do not dry items that have been previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances. They emit vapors that could ignite or explode. Any material that has been

in contact with a cleaning solvent or flammable liquids or solids should not be placed in the dryer until all traces of these flammable liquids or solids and their fumes have been removed. There are many highly flammable items used in homes, such as acetone, denatured alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers, turpentine, waxes, and wax removers.

•Items containing foam rubber (which may be labeled latex foam) or similarly textured rubberlike materials must not be dried on a heat setting. Heated foam rubber materials can, under certain circumstances, ignite spontaneously.

WARNING - Fire or explosion hazard

•Failure to follow safety warnings exactly could result in serious injury, death or property damage.

•Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance.

•Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

•Do not install a booster fan in the exhaust duct.

SAVE THESE INSTRUCTIONS

6  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 6			2020-12-07 4:50:48

WARNING - What to do if you smell gas:

•Do not try to light any appliance.

•Do not turn on the appliance.

•Do not touch any electrical switch.

•Do not use any phone in your building.

•Clear the room, building or area of all occupants.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire department.

<![if ! IE]>

<![endif]>information Safety

SAVE THESE INSTRUCTIONS

English  7 

DV3000A(SEM)_DC68-03784P-00_EN.indd 7			2020-12-07 4:50:48

<![if ! IE]>

<![endif]>information Safety

Safety information

CALIFORNIA PROPOSITION 65 WARNING

WARNING

Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Important safety precautions

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following:

1.Read all instructions before using this appliance.

2.Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.

3.Do not use the dryer to dry clothes which have traces of any flammable substance, such as vegetable oil, cooking oil, machine oil, flammable chemicals, paint thinner, etc., or anything containing wax or chemicals, such as mops and cleaning cloths. Flammable substances may cause the fabric to catch fire by itself.

4.Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance.

5.Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

6.Before the appliance is removed from service or discarded, remove the door to the drying compartment.

7.Do not reach into the appliance if the drum is moving.

8.Do not install or store this appliance where it will be exposed to the weather.

9.Do not tamper with internal controls.

10.Do not repair or replace any part of the appliance or attempt any service unless specifically recommended in the user-maintenance instructions or in published userrepair instructions that you understand and have the skills to carry out.

11.Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

12.Clean the lint screen before or after each load.

SAVE THESE INSTRUCTIONS

8  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 8			2020-12-07 4:50:48

13.Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

14.Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

15.The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.

16.Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire. To reduce the risk of fire due to contaminated loads, the final part of a tumble dryer cycle occurs without heat (cool down period). Avoid stopping a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.

17.This appliance must be grounded. See “Electrical requirements” and “Grounding” in “Installation” section.

18.Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

19.Do not insert your hand under the dryer.

•This may result in injury.

20.Take care that children’s fingers are not caught in the door when closing it.

•This may result in injury.

21.Control board and inlet valve are intentionally not grounded and may present a risk of electric shock only during servicing.

•Do not contact this part while appliance is energized.

Warnings

WARNING

•Ensure pockets are free from small, irregularly shaped hard objects, foreign material, etc. ie. coins, knives, pins, etc. These objects could damage your dryer.

•Gas leaks may occur in your system, resulting in a dangerous situation.

<![if ! IE]>

<![endif]>information Safety

SAVE THESE INSTRUCTIONS

English  9 

DV3000A(SEM)_DC68-03784P-00_EN.indd 9			2020-12-07 4:50:48

<![if ! IE]>

<![endif]>information Safety

Safety information

Cautions

CAUTION

•Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when the appliance is used near children and pets.

•Before discarding or removing your dryer from service, remove the door to the drying compartment to prevent children or animals from becoming trapped inside.

•Do not reach into the appliance when the drum is moving.

•Do not install or store this appliance where it will be exposed to the weather.

•Do not tamper with controls.

•Do not repair, replace, or attempt to service any part of the appliance unless specifically instructed to in the user-repair instructions and you have the understanding and skills to carry out the procedure.

•Do not use fabric softeners or products to eliminate static unless the softener or product is recommended for dryer use by the manufacturer of the fabric softener or product.

•Clean the lint screen before or after each load.

•Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt.

•The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel.

•This appliance must be properly grounded. Never plug the power cord into a receptacle that is not grounded adequately or not in accordance with local and national codes. See installation instructions for information about grounding this appliance.

•Do not sit on top of the dryer.

•Do not wash clothing with large buckles, buttons, or other heavy metal or solid objects.

•Gas leaks may not be detected by smell alone.

•Gas suppliers recommend you purchase and install a UL-approved gas detector.

•Install and use in accordance with the manufacturer’s instructions.

•Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking oil. Even after being washed, these items may contain significant amounts of these oils.

SAVE THESE INSTRUCTIONS

10  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 10			2020-12-07 4:50:48

	• Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous
	combustion increases when items containing vegetable oil or cooking oil are exposed
	to heat. Heat sources such as your dryer can warm these items, allowing an oxidation	<![if ! IE]> <![endif]>Safety
	reaction in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items
	can become hot enough to catch fire. Piling, stacking, or storing these kinds of items	<![if ! IE]> <![endif]>information
	may prevent heat from escaping and can create a fire hazard.
	• All washed and unwashed fabrics that contain vegetable oil or cooking oil can be
	dangerous.
	Washing these items in hot water with extra detergent will reduce, but not eliminate,
	the hazard. Always use the Cool Down cycle for these items to reduce their
	temperature. Never remove these items from the dryer hot or interrupt the drying
	cycle until the items have run through the Cool Down cycle. Never pile or stack these
	items when they are hot.

SAVE THESE INSTRUCTIONS

English  11 

DV3000A(SEM)_DC68-03784P-00_EN.indd 11			2020-12-07 4:50:48

<![if ! IE]>

<![endif]>requirements Installation

Installation requirements

Read through the following instructions before installing the dryer, and keep this manual for future reference.

WARNING

Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing.

Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve.

Key installation requirements

•A grounded electrical outlet.

•A power cord for electric dryers (except in Canada).

•Gas lines (for gas models) that must meet national and local regulations.

•An exhaust system made of rigid metal or flexible stiff-walled metal exhaust ducting.

WARNING

Remove the door from all discarded appliances to prevent a child from suffocating.

Location considerations

•Adequate clearances between the dryer and adjacent walls or other surfaces.

•Adequate air circulation for ventilation and gas combustion.

•Away from water and weather.

WARNING

•Make sure to exhaust the dryer outdoors to reduce the risk of fire.

•Keep the dryer area clear of combustible materials, gasoline, and other flammable vapors and liquids.

•Do not install other fuel-burning appliances around or in the same place as the dryer.

•Place the dryer at least 18 in. (460 mm) above the floor for a garage installation.

12  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 12			2020-12-07 4:50:49

Dimensions			A
				U
		9
		Type		Front loading dryer
		A. Overall height		43.9 (1117)
Dimensions		B. Width		27.0 (686)
(in. (mm))		C. Depth with door open		50.1 (1273)
		D. Depth		30.2 (768)

<![if ! IE]>

<![endif]>requirements Installation

English  13 

DV3000A(SEM)_DC68-03784P-00_EN.indd 13			2020-12-07 4:50:49

<![if ! IE]>

<![endif]>requirements Installation

Installation requirements

Clearance requirement

clearance requirement is applicable for dryers only.

NOTE

•For the washer’s clearance requirement, see the washer’s user manual.

•If the washer and dryer have different clearance requirements, follow the one with the larger value.

Alcove or closet installations

WARNING

•The dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or closet.

•No other fuel-burning appliance should be installed in the same closet as the dryer.

•Place the dryer at least 18 in. (460 mm) above the floor for a garage installation.

Minimum clearance for stable operation:

Sides	Top	Rear	Front
1 in. / 25 mm	17 in. / 432 mm	5.9 in. / 150 mm	1 in. / 25 mm

If both the washer and a dryer are installed in the same location, the front of the alcove or closet must have two unobstructed air openings for a combined minimum total area of 72 in.² (465 cm²).

This clearance requirement is applicable for washer and dryer pair installation.

Side by side installation

B

A

A

C

D

A

1 in. (25 mm)

B

21 in. (533 mm)

C

1 in. (25 mm)

D

5.9 in. (150 mm)

14  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 14			2020-12-07 4:50:50

Ducting requirements

		Recommended	Use only for short-run installation
	Weather hood
	type
		4” (10.2 cm)	2.5” (6.4 cm)
	No. of 90°	Rigid	Rigid
	elbows
	0	80 ft. (24.4 m)	74 ft. (22.6 m)
	1	68 ft. (20.7 m)	62 ft. (18.9 m)
	2	57 ft. (17.4 m)	51 ft. (15.5 m)
	3	47 ft. (14.3 m)	41 ft. (12.5 m)

NOTE

* Use a 4-inch (10.2 cm) diameter rigid aluminum or galvanized steel duct.

If you integrate the dryer’s vent system with an existing exhaust system, make sure:

•The exhaust system meets all applicable local, state, and national regulations.

•Not to use a flexible plastic duct.

•To regularly check and clean all lint buildup from inside the existing ducts.

•The duct is not kinked or crushed.

•The exhaust hood damper opens and closes freely.

Manometer measurements

The static pressure in any exhaust system must not exceed 0.83 inches of water column or be less than 0. Note that these values are measured with the dryer running with a manometer presented to the exhaust duct that connects to the dryer. The dryer drum must be empty and the lint filter clean.

<![if ! IE]>

<![endif]>requirements Installation

English  15 

DV3000A(SEM)_DC68-03784P-00_EN.indd 15			2020-12-07 4:50:50

<![if ! IE]>

<![endif]>requirements Installation

Installation requirements

Mobile home installation

The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada).

When installing a dryer in a mobile home, you must make provisions for anchoring the dryer to the floor.

Locate the dryer in an area that has adequate fresh air.

A minimum of 72 in² (465 cm²) of unobstructed space is required.

Call 1-800-SAMSUNG (726-7864) for information on purchasing the Floor Anchoring Kit as an accessory.

All mobile home installations must be exhausted to the outside with the exhaust duct termination securely fastened to the mobile home structure, using materials that will not support combustion.

The exhaust duct may not terminate underneath the mobile home. See the “Exhausting requirements” section for more information.

16  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 16			2020-12-07 4:50:50

Exhausting requirements

The dryer must not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a building. Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room.

In the United States and Canada

•All dryers must be exhausted to the outside.

•The required exhaust duct is 4 inches (10.2 cm) in diameter.

•See “Ducting requirements” in the “Installation” section for the maximum duct length and number of bends that can be used.

•The total length of the flexible metal duct must not exceed 7’ 101/2” (2.4 m).

•Do not assemble the duct with screws or other fastener means that extend into the duct and catch lint.

•For the United States only: Use only those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct. Use Subject

2158A.

Outside the United States and Canada

•Refer to the local codes.

WARNING

•You must exhaust the dryer to the outside to reduce the risk of fire when you install the dryer in an alcove or closet.

•Do not use a plastic or non-metal flexible duct.

•If your existing ductwork is plastic, nonmetal, or combustible, replace it with metal.

•Use only a metal exhaust duct that is non-flammable to ensure containment of exhaust air, heat, and lint.

<![if ! IE]>

<![endif]>requirements Installation

English  17 

DV3000A(SEM)_DC68-03784P-00_EN.indd 17			2020-12-07 4:50:50

Installation requirements

<![if ! IE]>

<![endif]>requirements Installation

Gas requirements

WARNING

•Use only natural or LP (liquid propane) gases.

•The installation must be conformed with local codes, or in the absence of local codes, with the national fuel gas code, ANSI Z223.1/NFPA 54, latest revision(for the UNITED STATES), or with the natural gas and propane installation code, CSA B149.1(for Canada).

•Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP (liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician. (LNG models only)

You must check the burner of your model and use the proper LP Kit accordingly. To check the detailed information of the

burner, open the door and check the rating label located on the door frame.

-20,000 BTU: LPKIT-4/XAA (DC98-04114A)

-22,000 BTU: LPKIT-3/XAA (DC99-00792A)

•A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-off valve be installed within 6” of your dryer.

•Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor.

•Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge connection, must be installed immediately upstream of your dryer’s gas supply connection.

•Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the system at pressures greater than 1/2 psi (3.5 kPa).

•Do not reuse old flexible metal gas lines. Flexible gas lines must be designed and certified by the standard for connectors for Gas Appliances, ANSI Z21.24 • CSA 6.10.

NOTE

•Your dryer uses an automatic ignition system to ignite the burner. There is no constant burning pilot.

•Any pipe joint compound used must be resistant to the action of any liquefied petroleum gas.

•As a courtesy, most local gas utilities will inspect a gas appliance installation.

Commonwealth of Massachusetts installation instructions

Your dryer must be installed by a licensed plumber or gas fitter. A “T” handle manual gas valve must be installed in the gas supply line to your dryer. If a flexible gas connector is used to install your dryer, the connector can be no longer than 3’ (36”).

WARNING

•Gas leaks may occur in your system, creating a dangerous situation.

•Gas leaks may not be detected by smell alone.

•Gas suppliers recommend you purchase and install a UL-approved gas detector.

•Install and use in accordance with the manufacturer’s instructions.

18  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 18			2020-12-07 4:50:51

Electrical requirements

The wiring diagram is located on the plate under the control panel or rear frame.

WARNING

•Improperly connecting the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. Do not modify the plug provided with your dryer – if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

•To prevent unnecessary risk of fire, electrical shock, or personal injury, all wiring and grounding must be done in accordance with local codes, or in the absence of local codes, in accordance with the National Electrical Code, ANSI/ NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 – Latest Revisions and local codes and ordinances. It is your responsibility to provide adequate electrical service for your dryer.

•All gas installations must be done in accordance with the National Fuel Code ANSI/Z2231 – Latest Revision (for the U.S.) or CAN/CGA – B149 Installation Codes – Latest Revision (for Canada) and local codes and ordinances.

Grounding

This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of electrical shock by providing a path of least resistance for the electrical current.

Gas models

WARNING

•Your dryer has a cord with an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

•Do not modify the plug provided with your dryer – if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

•Do not connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.

<![if ! IE]>

<![endif]>requirements Installation

English  19 

DV3000A(SEM)_DC68-03784P-00_EN.indd 19			2020-12-07 4:50:51

Installation requirements

<![if ! IE]>

<![endif]>requirements Installation

Electric models

WARNING

•Your dryer has an optional cord with an equipment-grounding conductor and a grounding plug. This cord is sold separately.

•The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

•Do not modify the plug provided with your dryer – if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

•If a power cord is not used and the electric dryer is to be permanently wired, the dryer must be connected to a permanently grounded metal wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the dryer.

Electrical connections

Before operating or testing, follow all grounding instructions in the “Grounding” section. An individual branch (or separate) circuit serving only your dryer is recommended.

Do not use an extension cord.

Gas models – U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service with a 15-ampere fuse or circuit breaker is required.

Electric models – U.S. only

Most U.S. dryers require a 120 / 240 volt, 60 Hz AC approved electrical service. Some require 120 / 208 volt, 60 Hz approved electrical service. The electric service requirements can be found on the data label located behind the door.

A 30-ampere fuse or circuit breaker on both sides of the line is required.

•If a power cord is used, the cord should be plugged into a 30-ampere receptacle.

•The power cord is not provided with U.S. electric model dryers. This cord is sold separately.

20  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 20			2020-12-07 4:50:51

WARNING

Risk of Electric Shock

When local codes allow, you can connect the dryer’s electrical supply with a new power supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of 120 / 240 volts, 30-amperes with three No. 10 copper wire conductors terminated with closed loop terminals, open-end spade lugs with turned up ends, or with tinned leads.

•Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring must be supported at the dryer cabinet by a suitable UL-listed strain relief.

•Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and

(4) areas where local codes prohibit grounding through the neutral conductor. (Use a 4-prong plug for a

4 wire receptacle, NEMA type 14-30R.)

Electric models – Canada Only

A 120 / 240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or circuit breaker on both

of the line is required.

NOTE

All Canadian models are shipped with the power cord attached. The power cord should be plugged into a 30-ampere receptacle. In Canada, you may convert a dryer to 120 / 208 volts.

<![if ! IE]>

<![endif]>requirements Installation

English  21 

DV3000A(SEM)_DC68-03784P-00_EN.indd 21			2020-12-07 4:50:51

Installation

This dryer must be installed by a qualified technician. The installer is responsible for connecting the dryer to the main power while observing the relevant safety regulations of your area.

What’s included

Make sure all the parts are included in the product package. If you have a problem with the dryer or the accessories, contact a local Samsung customer center or the retailer.

01

02

<![if ! IE]>

<![endif]>Installation

03

04

05

Dryer at a glance

01 Control panel	02 Worktop	03 Lint filter
04 Door	05 Exhaust duct

22  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 22			2020-12-07 4:50:51

Accessories & tools

Required tools

Pliers	Cutting knife	Pipe wrench (gas	Nut driver
		models only)

Level

Phillips screwdriver

Duct tape

Wrench

LPG-safe compound or Teflon Tape (for gas installation)

WARNING

Packing materials can be dangerous to children. Keep all packing materials (plastic bags, polystyrene, etc.) out of children’s reach.

<![if ! IE]>

<![endif]>Installation

English  23 

DV3000A(SEM)_DC68-03784P-00_EN.indd 23			2020-12-07 4:50:54

<![if ! IE]>

<![endif]>Installation

Installation

Step-by-step installation

Make sure you have a qualified technician install the dryer. Step by step installation instructions start below.

•Do not remove the protective film on the door before completing the product installation. If you remove the protective film before the installation is complete, the door may get scratched or damaged during installation.

•Make sure the installation location allows enough space for the dryer door to be fully open.

STEP  1  Install the exhaust system

1.Select a location and move the dryer to the site. For easy access, we recommend you install the dryer in the same location as your washer.

2.Install the exhaust system as instructed in the “Exhaust ducting guide” section.

CAUTION

Before installing your dryer, remove the packing material in the duct.

NOTE

•To move the dryer easily, lay two of the carton cushion-from the packaging on the floor. Tip the dryer on its side, so it lies across both cushion-tops. Push the dryer so that it is near its final location, and then set the dryer upright.

•Secure room around the dryer to facilitate ducting and wiring.

STEP  2  Connect the gas line

Before connecting the gas line, make sure you have read the “Gas requirements” section on page 18.

1.Remove the protective cap from the gas pipe.

2.Apply an LPG (Liquefied Petroleum Gas)-safe compound or 1.5 wraps of Teflon tape to all threaded connections.

3.Connect the gas supply to the dryer. An additional fitting is required to connect the 3/4” (1.9 cm) female thread end of a flexible connector to the 3/8” (1 cm) male threaded end on the dryer. Tighten up the fitting over all threads.

4.Turn on the gas supply, and check for any leaks using a soap solution. If a leak is found, tighten the connections and try again. DO NOT use an open flame to check for gas leaks.

24  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 24			2020-12-07 4:50:54

STEP  3  Connect the electrical wiring

First, read through the “Electrical requirements” section, and follow these steps.

3-wire system

1. Loosen or remove the screws from the center terminal block.

2. Connect the neutral wire (white or

center wire) of the power cable to the

center, silver-colored terminal screw of

the terminal block. Tighten the screws.

3. Connect the other wires to outer D terminal block screws. Tighten the

screws.

A	B	C	L2	L1	4.	Tighten the strain relief screws.
					5.	Insert the terminal block cover into the
				E		rear panel of the dryer. Then, secure the
						cover with a hold-down screw.

A.External ground connector

B.Neutral grounding wire (white)

C.Center silver-colored terminal block screw

D.Neutral wire (white or center wire)

E.3/4” (1.9 cm) UL-listed strain relief

CAUTION

•To convert from the 4-wire system to the 3-wire system, connect the ground strap to the terminal block support to ground the dryer frame to the neutral conductor.

•Ring-type terminals are recommended. If using strap terminals, make sure they are tightened.

•Connect the power cord and check L1/ L2/N voltage. If the voltage is low, it may not heat properly. Review the “Electrical requirements” section on page 19 if needed.

<![if ! IE]>

<![endif]>Installation

English  25 

DV3000A(SEM)_DC68-03784P-00_EN.indd 25			2020-12-07 4:50:54

Installation

<![if ! IE]>

<![endif]>Installation

4-wire system

F

A B C L2

D

L1

E

A.External ground connector

B.Neutral grounding wire (white)

C.Center silver-colored terminal block screw

D.Neutral wire (white or center wire)

E.3/4” (1.9 cm) UL-listed strain relief

F.Neutral wire (white or center wire)

CAUTION

1.Remove the external ground connector’s screw, and connect the ground wire (green or unwrapped) of the power cable to the screw.

CAUTION

•To connect the ground wire to the neutral position without contact A (cabinet ground), contact a technician.

It is not user serviceable.

•Ring-type terminals are recommended. If using strap terminals, make sure they are tightened.

2.Loosen or remove the screws from the center terminal block.

3.Connect the neutral wire (white or center wire) and ground wire (white) to the center screw of the terminal block. Tighten the screw.

4.Connect the other wires to the outer terminal block screws. Tighten the screws.

5.Tighten the strain relief screws.

6.Insert the tab of the terminal block cover into the rear slot of the dryer. Secure the cover with a hold-down screw.

Connect the power cord and check L1/L2/N voltage. If the voltage is low, it may not heat properly. Review the “Electrical requirements” section on page 19 if needed.

WARNING

•All U.S. models are designed for a 3-wire system connection. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-wire system connection is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal block.

•Remove the terminal block cover plate. Insert the power cord with a UL-listed strain relief through the hole provided in the cabinet near the terminal block.

26  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 26			2020-12-07 4:50:55

•A strain relief must be used. Do not loosen the nuts already installed on the terminal block. Be sure they are tight. Use a 3/8” (1 cm) deep well socket.

•Since january 1, 1996, The national electric code requires that new wiring (not existing) utilize a 4-wire connection to this dryer.

STEP  4  Level the dryer

To ensure optimal performance, the dryer must be level.

	1.	Gently slide the dryer into the desired
		location.
A	2.	Use a level (A) and check the levelness
		of the dryer from side to side and front
		to back.
	3.	If the dryer is not level, turn the
		leveling feet (B) left or right to adjust
		the height.
	4.	Once the dryer is level, make sure the
		dryer stands firmly on the floor.
	5.	Plug in the dryer.

B

<![if ! IE]>

<![endif]>Installation

			NOTE
			• To set the dryer to the same height
			as your washer, turn the leveling
			feet to the right until it fully retracts
	A	B	(A). Then, turn the leveling feet to
			the left to extend (B) until the dryer
			and the washer are the same height.
			• Extend the leveling feet only as
			much as necessary. Extending the
			leveling feet more than necessary
			can cause the dryer to vibrate.

English  27 

DV3000A(SEM)_DC68-03784P-00_EN.indd 27			2020-12-07 4:50:56

<![if ! IE]>

<![endif]>Installation

Installation

STEP  5  Power on (Gas models)

Make sure all gas connections, the exhaust line, and all wiring is connected correctly. Then, plug the power cord into a power source and check the dryer’s installation and operation using the final checklist in Step 6.

STEP  6  Final check

When the installation is complete, confirm that:

•The dryer is plugged into an electrical outlet and grounded properly.

•The exhaust ductwork is connected and the joints are taped.

•You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct.

•The dryer is level and is sitting firmly on the floor.

•The dryer starts, runs, heats, and shuts off properly.

For gas models:

•The gas is supplied properly with no leaks.

CAUTION

The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer off and wait 5 minutes. Be sure the gas supply to your dryer has been turned on. To confirm gas ignition, check the exhaust for heat.

Vent blockage test

After the dryer is installed, start the Vent Blockage Test to check if the duct system is properly installed. The Vent Blockage Test automatically detects the status of the ducts and reports any blockage or problems. Proper ducting can reduce drying time and save energy.

NOTE

You must run the Vent Blockage Test while the dryer is cool. If the dryer warms up after the installation check, run the AIR FLUFF cycle for several minutes to reduce its internal temperature.

Running the vent blockage test

1.Make sure the drum is empty, and then close the door.

•If there are any clothes or other items in the drum, the test will not give accurate results.

2.Press the POWER button to turn on the dryer.

28  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 28			2020-12-07 4:50:56

	3. Press and hold the Temp. and START/PAUSE buttons simultaneously for 3 seconds.
	• The Drying, Cooling, and High LEDs turn on.
	• If you have started other procedures before the Vent Blockage Test, the dryer will
	not enter the Vent Blockage Test mode.
	4. Press the START/PAUSE button.
	• The Vent Blockage Test starts immediately. During the test, the Drying, Cooling and
	High LEDs blink.
	• Do not open the door during the test.
	5. After 2 minutes, when the test is complete, the result is displayed and the dryer sounds
	a tone.
	• If the status of the duct system is normal, the End LED turns on, and the dryer	<![if ! IE]> <![endif]>Installation
	sounds a completion tone.
	• If the duct system cannot exhaust properly, “Installation check code” is displayed on
	the control panel, and the dryer sounds an alarm tone. For a description of the code,
	see the “Installation check codes” section on page 30.
	• If there are any other problems, an information code appears in the display. For a
	description of the code, see the “Information codes” section on page 48.
	NOTE

•During or after the test, the internal drum is hot. Use caution to prevent burns.

The Vent Blockage Test is used to check for problems to the current duct system when the dryer is installed for the first time.

•If the test result displays check code (the duct system is blocked ), refer to the “Ducting requirements” section on page 15 and the “Exhaust ducting guide” section below,

and then take proper measures to correct any problems.

If the test is suspended, it could result in incorrect results. Follow the proper procedures when testing the dryer.

•Even if the test result is normal (the End LED on), the duct system could be blocked slightly. Properly install all ductwork according to the installation instructions in this manual.

English  29 

DV3000A(SEM)_DC68-03784P-00_EN.indd 29			2020-12-07 4:50:56

Installation

<![if ! IE]>

<![endif]>Installation

Installation check codes

: LED ON, : LED Blink

Display

Temp.

Time (min.)

Check code

Drying

Cooling

Wrinkle

End

Extra

Low

Medium

High

20

40

60

80

Prevent

Low

Ins







0



C80

















C90

























Ct









tC



C1









dC



9C1



Check code

Meaning

Solution

0

Vent condition is good.

Clg (Cg)

The vent is clogged.

1.

Clean the lint filter.

About 80 % of the vent is clogged.

2.

Check your vent condition.

C80 (C8)

(This may decrease the drying

(Refer to the “Ducting

performance.)

requirements” section)

* You must take measures (such

Over 90 % of the vent is clogged.

C90 (C9)

(This may lead to poor drying

as cleaning) through expert

performance or cause malfunction)

personnel.

The internal temperature of the

dryer is too low (below 32 °F (0 °C))

Leave the dryer at room

Ct

or too high (over 104 °F (40 °C)) and

temperature (41~95 °F (5~35 °C))

therefore, vent blockage cannot be

for an hour and check again.

detected.

tC

Temperature sensor error.

Contact a service center.

The unit is detecting items inside

Remove items from the drum and

check again.

C1

the drum, or there is an error on the

If the problem continues, contact a

dry sensor.

service center.

30  English

DV3000A(SEM)_DC68-03784P-00_EN.indd 30			2020-12-07 4:50:56