SAMSUNG DVD-1080PR User Manual

DVD Player
user manual
DVD-1080P9 DVD-1080PR
AK68-01750R(03)
imagine the possibilities
Thank you for purchasing this Samsung product. To receive more complete service, please register your product at
www.samsung.com/global/register
precautions
1. Setting up
- Refer to the identification label located on the rear of your player for its proper operat­ing voltage.
- Install your player in a cabinet with ade­quate ventilation holes. (7~10cm) Do not block ventilation holes on any of the compo­nents for air circulation.
- Do not push the disc tray in by hand.
- Do not stack components.
- Be sure to turn all components off before moving the player.
- Before connecting other components to this player, be sure to turn them off.
- Be sure to remove the disc and turn off the player after use, especially if you are not going to use it for a long time.
- The mains plug is used as a disconnect device and shall stay readily operable at any time.
2. For your safety
- This product utilizes a laser. Use of controls or adjustments or performance of proce­dures other than those specified herein may result in hazardous radiation exposure.
- Do not open covers and do not repair your­self. Refer servicing to qualified personal.
3. Caution
- Your player is not intended for industrial use but for domestic purposes. Use of this prod­uct is for personal use only.
- Apparatus shall not be exposed to dripping or splashing and no objects filled with liq­uids, such as vases, shall be placed on the apparatus.
- Exterior influences such as lightning and static electricity can affect normal operation of this player. If this occurs, turn the player off and on again with the POWER button, or disconnect and then reconnect the AC power cord to the AC power outlet. The player will operate normally.
- When condensation forms inside the player due to sharp changes in temperature, the
player may not operate correctly. If this occurs, leave the player at room tempera­ture until the inside of the player becomes dry and operational.
4. Disc
- Do not clean disc using record-cleaning sprays, benzene, thinner, or other volatile solvents that may cause damage to the disc surface.
- Do not touch the disc’s signal surface. Hold by the edges or by one edge and the hole in the center.
- Wipe the dirt away gently; never wipe a cloth back and forth over the disc.
5. Environmental info
- The battery used in this product contains chemicals that are harmful to the environ ment.
- So, dispose of batteries in the proper man ner, according to federal, state, and local regulations.
The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private non-commercial use by end-user consum­ers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/OUR 11172-3 or ISO/OUR 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/OUR 11172-3 or ISO/OUR 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/OUR 11172-3 or ISO/OUR 13818-3.
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
2_ precautions
before you start
table of contents
Accessories
Check for the supplied accessories below.
Batteries for Remote
Remote Control
User’s Manual
The accessories which do not suplied.
Scart Cable HDMI-HDMI Cable
Component Cable HDMI-DVI Cable
Coaxial Cable
Install Batteries in the Remote control
1. Open the battery cover on the back of the remote control.
2. Insert two AAA batteries. Make sure that the polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
If remote control doesn’t operate properly:
- Check the polarity + - of the batteries (Dry-Cell)
- Check if the batteries are drained.
- Check if remote control sensor is blocked by obstacles.
- Check if there is any fluorescent lighting nearby.
- The rechargeable battery incorporated in this product is not user replaceable.
- For information on its replacement, please contact your service provider.
Control (AAA Size)
Video/Audio
Cable
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . .4
Disc Type and Characteristics . . . . . . . . . . . . . . . .5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Tour of the Remote Control . . . . . . . . . . . . . . . . . . .8
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . . . . .9
Basic Functions
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Using the Search and Skip Functions . . . . . . . . .16
Using the Display Function . . . . . . . . . . . . . . . . .17
Using the Disc and Title Menu . . . . . . . . . . . . . . .17
Using the Function Menu . . . . . . . . . . . . . . . . . . .18
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Advanced Functions
Adjusting the Aspect Ratio (EZ View) . . . . . . . . . .19
Selecting the Audio Language . . . . . . . . . . . . . . .19
Selecting the Subtitle Language . . . . . . . . . . . . . .20
Changing the Camera Angle . . . . . . . . . . . . . . . . .20
Using the Bookmark Function . . . . . . . . . . . . . . . .20
Using the Zoom Function . . . . . . . . . . . . . . . . . . .21
Clips Menu for MP3/WMA/JPEG/MPEG4/
CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . .22
MP3/WMA/CD Audio Playback . . . . . . . . . . . . . . .22
MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . .23
Playing Media Files using the USB HOST
feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
CD Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Picture CD Playback . . . . . . . . . . . . . . . . . . . . . . .25
Picture CD Playback for HD-JPEG . . . . . . . . . . . .26
Changing Setup Menu
Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . .27
Setting Up the Language Features . . . . . . . . . . . .27
Setting Up the Audio Options . . . . . . . . . . . . . . . .28
Setting Up the Display Options . . . . . . . . . . . . . . .29
Setting Up the Parental Control . . . . . . . . . . . . . .32
Setting Up the Anynet+(HDMI-CEC) . . . . . . . . . . .33
Reference
Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . .34
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
English _3
setup
General Features
Excellent Sound
Dolby Digital, a technology developed by Dolby Laboratories, provides crystal clear sound reproduc­tion.
Screen
Both regular and widescreen(16:9) pictures can be viewed.
Slow Motion
An important scene can be viewed in slow motion.
1080p Playback
This player upconverts regular DVDs for playback on 1080p TVs.
Parental Control (DVD)
The parental control allows users to set the level necessary to prohibit children from viewing harmful movies such as those with violence, adult subject matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle) and screen angles while enjoying movies.
Progressive Scan
Progressive scanning creates an improved picture with double the scan lines of a conventional inter­laced picture.
EZ VIEW (DVD)
Easy View enables picture adjustment to match your TV's screen size (16:9 or 4:3).
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
Repeat
You can repeat a song or movie simply by pressing the REPEAT button.
MP3/WMA
This unit can play discs created from MP3/WMA files.
MPEG4
This unit can play MPEG4 formats within an avi file.
HDMI (High Definition Multimedia Interface)
HDMI reduces picture noise by allowing a pure digital video/audio signal path from the player to your TV.
CD Ripping
This feature lets you to copy audio files from disc to USB device into MP3 format. (Only Audio CD (CD DA))
Note
- Discs which cannot be played with this player.
• DVD-ROM • DVD-RAM
• CD-ROM • CDV
• CDI • CVD
• CDGs play audio only, not graphics.
- Ability to play back may depend on recording conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW (V mode)
- The unit may not play certain CD-R, CD-RW and DVD-R due to the disc type or recording
conditions.
COPY PROTECTION
Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy­protected DVD discs.
This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be auzthorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise autho­rized by Macrovision Corporation. Reverse engi­neering or disassembly is prohibited.
PROGRESSIVE SCAN OUTPUTS (576p,720p,1080p)
“CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE, IN CASE OF 576, 720, 1080 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING YOUR TV SET COMPATIBILITY WITH THIS MODEL 576p, 720p, 1080p DVD PLAYER, PLEASE CONTACT SAMSUNG'S CUSTOMER SERVICE CENTER.”
4_ setup
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos:
Disc Types (Logos)
DVD
AUDIO-CD
Disc Markings
~
Play Region Number
PAL
STEREO
DIGITAL
SOUND
PAL broadcast system in U.K, France, Germany, etc.
Dolby Digital disc
Stereo disc
Digital Audio disc
DTS disc
Recording Types Disc Size Max. Playing Time
Single-sided 240 min.
Double-sided 480 min.
Single-sided 80 min.
Double-sided 160 min.
74 min.
20 min.
Audio
+
Video
Audio
12 Cm
8 Cm
12 Cm
8 Cm
Region Number
Both the DVD player and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play.
The Region Number for this player is described on the rear panel of the player.
Characteristics
- DVD contains excellent sound and video due to Dolby Digital and MPEG­2 system.
- Various screen and audio functions can be easily selected through the on­screen menu.
- CD is recorded as a Digital Signal with better audio quality, less distor­tion and less deterioration of audio quality over time.
SETUP
MP3 disc
You must only insert one DVD disc at a time. Inserting two or more discs will not allow to play them back and it may cause damage to the DVD player.
DivX Certification
DivX, DivX Certified, and associated logos are trademarks of DivXNetworks, Inc and are used under license
English _5
setup
7
8
9
7
Description
Front Panel Controls
1. DISC TRAY
Place the disc here.
2. OPEN/CLOSE ( )
Press to open and close the disc tray.
3. DISPLAY
Operation indicators are displayed here.
4. PLAY/PAUSE (
Begin or pause disc play.
5. SKIP ( ) / SEARCH
Use to forward skip a scene or music.
)
Front Panel Display
DVD
1. In Disc Indicator : DVD Video, Audio CD, CD-R/RW, DVD-R/RW/RAM, DVD+R/RW
2. DVD VIEW indicator
3. CD indicator
4. USB indicator
5. Disc Media indicator : DVD-R, DVD­RW, DVD+R, DVD+RW
6. STOP ( )
Stops disc play.
7. SKIP ( ) / SEARCH
Use to reverse skip a scene or music.
8. USB HOST
Connect digital still camera, MP3 player, memory stick,
Card reader other removable storage devices.
9. POWER ON/OFF ( )
Turn on/off and the player is turned on/off.
USB
HDMI 1080iP720P
RW
“HDMI”, “HDMI + 720P”,
“HDMI + 1080i”,
“HDMI + 1080P”
CD
6. HDMI indicator : HDMI 480P HDMI 720P HDMI 1080i HDMI 1080P
7. Displays the Total playing time and various messages concerning operations such as PLAY, STOP, LOAD ...
noDISC: No disc loaded. OPEN: The disc tray is open. LOAD: Player is loading disc information.
6_ setup
Rear Panel
SETUP
1. SCART JACK
- Connect to a TV scart input jack
2. AUDIO OUT JACKS
- Connect to the Audio input jacks of your television or audio/video receiver.
3. DIGITAL AUDIO JACKS
- Use either an coaxial digital cable to connect to a compatible Dolby Digital receiver.
- Use either an coaxial digital cable to connect to an A/V Amplifier that contains a Dolby Digital, MPEG2 or DTS decoder.
4. COMPONENT VIDEO OUT JACKS
- Use these jacks if you have a TV with Component
Video in jacks. These jacks provide PR, PB and Y video.
- If P-SCAN Video Output is selected in Setup Menu, progressive scan mode will work.
- If I-SCAN Video Output is selected in Setup Menu, interlaced scan mode will work.
5. HDMI OUT JACK
- Use the HDMI cable to connect this jack to the HDMI jack on your television for the best quality picture.
- If an HDMI cable is connected to an HDMI-compat­ible TV, HDMI will be output automatically within 10 seconds.
6. VIDEO OUT JACK
- Use a video cable to connect to the Video input jack on your television.
Note
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN).
If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system.
- The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conver-
sion adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input.
- There may be no image output if the DVD player is connected to a TV or display that is not compatible
with the above format.
- Refer to the TV's instruction manual for detailed information regarding the HDMI terminal.
- See pages
29 ~ 31 to get more information on how to use the setup menu.
English _7
setup
Tour of the Remote Control
1
2
3
4
5
6 7
8 9
10 11
12
13 14
15 16
1. DVD POWER Button
Turns the power on or off.
2. NUMBER Buttons
3. SUBTITLE (Number 4) Button
4. TITLE MENU (Number 7) Button
Brings up the Title Menu.
5. ZOOM/-/-- Button
Enlarges the DVD Picture. Use this button to select the
channel TV program by inserted the channel (TV mode).
6. TV VOL (+, -) Buttons
Control volume.
7. SEARCH Buttos (
Allow you to search forward/backward through a disc.
k/K
)
8_ setup
17 18
19 20
21 22
23
24
25
26 27
28 29
30 31
8. VIDEO SEL. Button
Selects video output formats.
9. SKIP Buttons (
Use to skip the title, chapter or track.
10. STOP Button (■)
11. MENU Button
Brings up the DVD player’s menu.
12. ENTER/π/†,√/® Buttons
This button functions as a toggle switch.
13. INFO Button
Displays the current disc mode.
14. DISC MENU Button
Brings up the Disc menu.
15. OPEN/CLOSE ( ) Button
To open and close the disc tray.
16. HDMI SEL. Button
HDMI Output resolution setup.
17. DVD Button
This button when you use a DVD player.
18. TV Button
This button when you use a Samsung TV.
19. EZ VIEW (Number 6) Button
The aspect ratio of a picture can easily be adjusted
according to the screen size of your TV (16:9 or 4:3).
20. AUDIO (Number 5) Button
Use this button to access various audio functions on a disc.
21. BOOKMARK (Number 9) Button
22. REPEAT A-B (Number 8) Button
Allows you to repeat play A-B on a disc.
23. STEP/TV SOURCE Button
Advances play one frame at a time. Use this button to
select an available TV source (mode TV)
24. TV CH (
Channel selection.
25. PAUSE Button (
Pause disc play.
26. PLAY Button ()
Begin disc play.
27. RETURN Button
Returns to a previous menu.
28. EXIT Button
Exit the on-screen menu.
29. CANCEL Button
Use to remove menus or status displays from the screen.
30. USB Button
31. REPEAT Button
Allows you to repeat play a title, chapter, track, or disc.
P, Q
|k/K|
) Buttons
∏∏
)
)
connections
Choosing a Connection
The following shows examples of connections commonly used to connect the DVD player with a TV and other components.
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
- Refer to the user’s manual of the additional components you are connecting for more information on those particular components.
Connecting to a TV (VIDEO CVBS)
1
Using video/audio cables, connect the VIDEO (yellow)/ AUDIO (red and white) OUT terminals on the rear of the DVD player to the VIDEO (yellow)/AUDIO (red and white) IN terminals of TV.
CONNECTIONS
2
Turn on the DVD player and TV.
WHITE
RED
RED
Audio Cable
WHITE
YELLOW
Video Cable
YELLOW
3
Press the input selector on your TV remote control until the Video signal from the DVD player appears on the TV screen.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 14 to 15)
- The number and position of terminals can vary depending on your TV set. Please refer to the user's manual of the TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the DVD player.
- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video Output mode changes in the following sequence: (I-SCAN P-SCAN SCART-RGB SCART-CVBS)
English _9
connections
Connection to a TV (Interlace)
- Connecting to your TV using Component video cables.
- You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio signals are delivered through the audio output.)
1
Using component video cables, connect the COMPONENT VIDEO OUT terminal on the rear of the DVD player to the COMPONENT IN terminal of TV.
2
Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the
DVD player and TV.
3
Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV screen.
WHITE
RED
RED
Audio Cable
WHITE
RED
Do not use the connection Scart and Component Video (Y, Pb, Pr) simul­taneously.
GREEN
RED
BLUE
GREEN
BLUE
Component Cable
4
Set the Video Output to I-SCAN in the Display Setup menu. (See pages 29 to 31) You can use the VIDEO SEL. button to change the Video Output mode. (See page 9)
Note
-
If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 14 to 15)
- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “PR, PB, Y” depending on the manufacturer. The number and position of terminals can vary depending on the TV set. Please refer to the user's manual of the TV.
- There is no Component video displayed when "Scart RGB" selected by pressing video select button on remote control.
10_ connections
Connection to a TV (Progressive)
1
Using component video cables, connect the COMPONENT VIDEO OUT terminal on the rear of the DVD player to the COMPONENT IN terminal of TV.
2
Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the
DVD player and TV.
3
Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV screen.
4
Set the Video Output to P-SCAN in the Display Setup menu. (See pages 29 to 31) You can use the VIDEO SEL. button to change the Video Output mode. (See page 9)
WHITE
RED
RED
Audio Cable
WHITE
RED
Do not use the connection Scart and Component Video (Y, Pb, Pr) simul­taneously.
GREEN
RED
BLUE
GREEN
BLUE
Component Cable
CONNECTIONS
To see the progressive video output,
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive
Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system.
- Depending on your TV, the connection method may differ from the illustration above.
Note
- What is "Progressive Scan"? Progressive scan has twice as many scanning lines as the interlace output method has. Progressive scanning method can provide better and clearer picture quality.
- There is no Component video displayed when "Scart RGB" selected by pressing video select button on remote control.
English _11
connections
Connecting to a TV (SCART)
1
Using scart cable, connect to SCART terminal on the rear of the DVD player to the SCART IN terminals of TV.
2
Turn on the DVD player and TV.
3
Press the input selector on your TV remote control until the Video signal from the DVD player appears on the TV screen.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 14 to 15)
- The number and position of terminals can vary depending on your TV set. Please refer to the user's manual of the TV.
- Please do not connect Scart and Component Video (Y, Pb, Pr) output simultaneously, as they may inter­fere and degrade both video output quality.
Scart Cable
Do not use the connection Scart and
Component Video (Y, Pb, Pr) simul-
taneously.
12_ connections
Connecting to a TV with DVI Jack
1
Using the HDMI-DVI cable , connect the HDMI OUT ter­minal on the rear of the DVD player to the DVI IN terminal of your TV.
CONNECTIONS
2
Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of your TV. Turn on
the DVD player and TV.
3
Press the input selector on your TV remote control until the DVI signal from the DVD player appears on your TV screen.
Connecting to a TV with HDMI Jack
1
Using the HDMI-HDMI cable connect the HDMI OUT termi­nal on the rear of the DVD player to the HDMI IN terminal of your TV.
2
Press the input selector on your TV remote control until the HDMI signal from the DVD player appears on your TV screen.
WHITE
RED
Audio Cable
WHITE
RED
HDMI-DVI cable
HDMI cable
HDMI VIDEO Specifications
When you press the HDMI SEL. button, 480p, 576p, 720p, 1080p, 1080i are selected in order. The first press of the HDMI SEL. button brings up the current resolution. The second press allows you to change the HDMI output resolution.
- Depending on your TV, certain HDMI output resolutions may not work.
- Please refer to the user's manual of your TV.
- If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10
seconds.
- If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture
quality.
- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this DVD player
using your TV remote control. This is only available with Samsung TVs that support Anynet+(HDMI-CEC). (See page 33).
- If your TV has an logo, then it will Supports the Anynet+ Function.
English _13
connections
• HDMI (High Definition Multimedia Interface)
HDMI is an interface to enable the digital transmission of video and audio data with just a single connector. Using HDMI, the DVD player transmits a digital video and audio signal and displays a vivid picture on a TV having an HDMI input jack.
• HDMI connection description
HDMI connector - Both uncompressed video data and
digital audio data (LPCM or Bit Stream data).
- Though the player uses a HDMI cable, the player outputs only a pure digital signal to the TV.
- If TV does not support HDCP (High-bandwidth Digital content protection), snow noise appears on the screen.
• Why does Samsung use HDMI?
Analog TVs require an analog video/audio signal. However, when playing a DVD, the data transmitted to a TV is digital. Therefore either a digital-to-analog converter (in the DVD player) or an analog-to-digital converter (in the TV) is required. During this conver­sion, the picture quality is degraded due to noise and signal loss. DVI technology is superior because it requires no D/A conversion and is a pure digital sig­nal from the player to your TV.
• What is the HDCP?
HDCP (High-bandwidth Digital Content Protection) is a system for protecting DVD content outputted via DVI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display device (TV, projector . etc). Content is encrypted at the source device to prevent unauthorized
Connection to an Audio System (2 Channel Amplifier)
1
Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO or COMPONENT OUT terminals on the rear of the DVD
player to the VIDEO or COMPONENT IN terminal of your TV as described on pages 9 to 14.
3
Turn on the DVD player, TV, and Amplifier.
Audio Cable
WHITE
RED
2-Channel stereo
ampilfier
RED WHITE
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 28-29)
- The position of terminals can vary depending on the Amplifier. Please refer to the user's manual of the Amplifier.
14_ connections
Connection to an Audio System (Dolby Digital, MPEG2 or DTS Amplifier)
1
If using a coaxial cable, connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the DVD player to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO, COMPONENT or HDMI OUT terminals on the rear of the
DVD player to the VIDEO, COMPONENT or DVI IN termi­nals of your TV as described on pages 9 to 14.
Coaxial Cable
CONNECTIONS
3
Turn on the DVD player, TV, and Amplifier.
Dolby Digital or
DTS amplifier
4
Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player. Refer to your Amplifier's user manual to set the Amplifier's audio input.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 28 to 29)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
English _15
basic functions
Playing a Disc
Before Play
- Turn on your TV and set it to the correct Video Input by pressing TV/VIDEO button on the TV remote control.
- If you connected an external Audio System, turn on your Audio System and set it to the correct Audio Input.
After plugging in the player, the first time you press the DVD POWER button, this screen comes up: If you want to select a language, press a NUMBER button. (This screen will only appear when you plug in the player for the first time.) If the language for the startup screen is not set, the set­tings may change whenever you turn the power on or off. Therefore, make sure that you select the language you want to use. Once you select a menu language, you can change it by pressing the more than 5 seconds with no disc in the unit. Then the SELECT MENU LANGUAGE window appears again where you can reset your preferred language.
button on the front panel of the unit for
Press 1 for English Touche 2 pour Français Drücken Sie 3 für Deutsch Pulsar 4 para Español Premere 5 per Italiano Druk op 6 voor Nederlands
7. Step Motion Play (Except CD) Press the STEP button on the remote control during play.
- Each time the button is pressed, a new frame will appear.
- No sound is heard during STEP mode.
- Press the PLAY (
- You can only perform step motion play in the forward direction.
8. Slow Motion Play Press the SEARCH ( speed between 1/2, 1/4 and 1/8 of normal during PAUSE or STEP mode.
- No sound is heard during slow mode.
- Press the PLAY (
) button to resume normal play.
k/K) button to choose the play
) button to resume normal play.
Note
- If the player is left in the stop mode for more than one minute without any user interaction, a screen saver will be activated. Press the PLAY () button to resume normal play.
- If the player is left in the stop mode for more than about 30 minutes, the power will automatically shut off.(Automatic Power-Off Function)
- If the player is left for about 5 minutes in pause mode, it will stop.
- This ( ) icon indicates an invalid button press.
Playback
1. Press the OPEN/CLOSE ( ) button and the tray opens.
2. Place a disc gently into the tray with the disc’s label facing up.
3. Press the PLAY ( button to close the disc tray.
-
When you stop disc play, the player remembers
where you stopped, so when you press PLAY ( button again, it will pick up where you left off.
4. Stopping Play Press the STOP (
5. Removing Disc Press the OPEN/CLOSE (
6. Pausing Play
Press the PAUSE ( control during play.
- Screen stops, no sound. To resume, press the PLAY (
) button or OPEN/ CLOSE ( )
) button during play.
) button.
∏∏
) or STEP button on the remote
)-button once again.
16_ basic functions
Using the Search and Skip Functions
During play, you can search quickly through a chapter or track, and use the skip function to jump to the next selection.
Searching through a Chapter or Track
During play, press the SEARCH (k or K) button on the
)
remote control for more than 1 second.
DVDCD2X, 4X, 64X, 128X
2X, 4X, 8X
Note
- The speed marked in this function may be different from the actual playback speed.
- No sound is hearing during search mode (Except CD).
Skipping Tracks
MenuReturnEnter
MenuReturnEnter
Title
Chapter
Time
Audio
Subtitle
During play, press the SKIP (|k or K|) button.
- When playing a DVD, if you press the SKIP (K|) button,
|k
it moves to the next chapter. If you press the SKIP ( button, it moves to the beginning of the chapter. One more press makes it move to the beginning of the previous chapter.
- When playing a CD in Menu Off mode, if you press the
K|
SKIP ( the SKIP ( track. One more press makes it move to the beginning of the previous track.
) button, it moves to the next track. If you press
|k
) button, it moves to the beginning of the
)
Using the Display Function
When Playing a DVD/MPEG4
1. During play, press the INFO button on the remote control.
- You can select Info in the function menu by pressing the MENU button.
2. Press the π/buttons to select the desired item.
3. Press the √/® buttons to make the desired setup and then press the ENTER button.
- You may use the number buttons of the remote control to directly access a title, chapter or to start the play back from a desired time.
4.
To make the screen disappear, press the INFO button again.
Note
Using the Disc and Title Menu
Using the Disc Menu
1. During the playback of a DVD disc, press the MENU button on the remote control.
2. Press the π/ buttons to select Disc Menu, then press the ® or ENTER button.
Press ENTER key for Disc Menu
Note
- Depending on a disc, the Disc Menu may not work.
- You can also use the Disc Menu, using the DISC MENU button on the remote control.
Using the Title Menu
1. During the playback of a DVD disc, press the MENU button on the remote control.
2. Press the π/ buttons to select Title Menu, then press the ® or ENTER button.
BASIC FUNCTIONS
To access the desired title when there is more than one in the disc. For example, if there is more than one movie on a DVD, each movie will be identified.
Most DVD discs are recorded in chapters so that you can quickly find a specific passage.
Allows playback of the film from a desired time. You must enter the starting time as a reference.The time search function does not operate on some disc.
Refers to the language of the film soundtrack. In the example, the soundtrack is played in English 5.1CH. A DVD disc can have up to eight different soundtracks.
Refers to the subtitle languages available in the disc. You will be able to choose the subtitle languages or, if you prefer, turn them off from the screen. A DVD disc can have up to 32 different subtitles.
Press ENTER key for Title Menu
Note
- Depending on a disc, the Title Menu may not work.
- Title Menu will only be displayed if there are at least two titles in the disc.
English _17
basic functions
MenuReturnEnter
Using the Function Menu
Using the Function Menu (DVD)
1. Press the MENU button during playback.
2. Press the π/ buttons to select Function, then press the ® or ENTER button.
- Info (See pages 17)
- Zoom (See page 21)
- Bookmark (See pages 20 to 21)
- EZ View (See pages 19)
- Angle (See pages 20)
Info Zoom Bookmark EZ View Angle
3. Press the π/ buttons to select one of the six functions. Then press the ® or ENTER button to access the function. You can also directly select these functions using their respective buttons on the remote control.
- INFO - ZOOM
- EZ VIEW - BOOKMARK
- REPEAT
Repeat Play
Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc.
When playing a DVD
1. Press the REPEAT button on the remote control. Repeat screen appears.
- DVD repeats play by chapter or title.
- Chapter : repeats the chapter that is playing.
- Title : repeats the title that is playing.
- Repeat : Off
Using the A-B Repeat function
1. Press the REPEAT A-B button at the point where you want repeat play to start (A).
2. Press the REPEAT A-B button at the point where you want the repeat play to stop (B).
2.
To return to normal play, press the REPEAT A-B button.
Repeat:A-
Repeat:A-B
Repeat:Off
Note
- A-B REPEAT allows you to set point (B) until at least 5 seconds of play back time has elapsed
after point (A) has been set.
- Depending on a disc, the Repeat function may not work.
Slow Play
This feature allows you slowly to repeat scenes con­taining sports, dancing, musical instruments being played etc., so you can study them more closely.
When playing a DVD
1. During play, press the PAUSE (∏∏) button.
2. Press the SEARCH (k/K) button to choose the play speed between 1/2, 1/4 and 1/8 of normal during PAUSE or
STEP mode.
18_ basic functions
Chapter
Title
Repeat:Off
EZ VIEW
ENG
Dolby Digital 5.1CH
AUDIO
AUDIO
advanced functions
Adjusting the Aspect Ratio (EZ View)
To play back using aspect ratio (DVD)
Press the EZ VIEW button.
- The screen size changes when the button is pressed repeatedly.
- The screen zoom mode operates differently depending on the screen setting in the Display Setup menu.
- To ensure correct operation of the EZ VIEW button, you should set the correct aspect ratio in the Display Setup menu. (See pages 29 to 31).
WIDE SCREEN
If you are using a 16:9 TV
For 16:9 aspect ratio discs
- WIDE SCREEN Displays the content of the DVD title in 16:9 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the black bars at the top and bottom of the screen will disappear. The picture will look vertically stretched. (Depending on a type of disc, the black bars may not disappear completely.)
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarge
For 4:3 aspect ratio discs
- Normal Wide
Displays the content of the DVD title in 16:9 aspect ratio.
The picture will look horizontally stretched.
- SCREEN FIT
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are
cut off and the central portion of the screen is enlarged.
- Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black bars will
appear at the left and right of the screen in order to prevent the picture from looking horizontally stretched.
If you are using a 4:3 TV
For 16:9 aspect ratio discs
- 4:3 Letter Box
Displays the content of the DVD title in 16:9 aspect ratio.
The black bars will appear at the top and bottom of the screen.
- 4:3 Pan Scan
The left and right portions of the screen are cut off and the central portion of the 16:9 screen is displayed.
- SCREEN FIT The top and bottom portions of the screen are cut off and a full screen appears. The picture will look vertically stretched.
- ZOOM FIT The top, bottom, left and right of the screen are cut off and the central portion of the screen is enlarged.
For 4:3 aspect ratio discs
- Normal Screen
Displays the content of the DVD title in 4:3 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off and the
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are cut off and the central portion of the screen is enlarged.
Note
This function may behave differently depending on the type of disc.
Selecting the Audio Language
You can select a desired audio language quickly and easily with the AUDIO button.
Using the AUDIO button (DVD/ MPEG4)
1. Press the AUDIO button. The Audio changes when the button is pressed repeatedly. The audio languages are represented by abbreviations.
Press AUDIO button at remocon repeatedly to select the desired Audio on MPEG4 then press the ENTER .
2. To remove the AUDIO icon, press the CANCEL or RETURN button.
DVD
MPEG4
MP3 1/1
ADVANCED FUNCTIONS
English _19
advanced functions
SUBTITLE
SUBTITLE
MenuReturnEnter
MenuReturnEnter
Note
- This function depends on audio languages are encoded on the disc and may not work.
-
A DVD disc can contain up to 8 audio languages.
- To have the same audio language come up whenever you play a DVD;
Refer to “Using the Audio Language” on page 28.
Selecting the Subtitle Language
You can select a desired subtitle quickly and easily with the SUBTITLE button.
Using the SUBTITLE button (DVD/ MPEG4)
1. Press the SUBTITLE button. The subtitle languages are represented by abbreviations. The subtitle changes when the button is pressed repeatedly.
External subtitle option will appear, depends the DivX Disc.
Press Subtitle button at remocon repeatedly to select the desired subtitle language on a MPEG4.
2. To remove the SUBTITLE icon, press the CANCEL or RETURN button.
Note
- You have to change the desired subtitle in the Disc Menu, according to discs. Press the DISC MENU button.
- This function depends on what subtitles are encoded on the disc and may not work on all DVDs.
- A DVD disc can contain up to 32 subtitle languages.
- To have the same subtitle language come up whenever you play a DVD; Refer to “Using the Subtitle Language” on page 28.
20_ advanced functions
DVD
ENG
MPEG4
Subtitle Selection
External Subtitle Off
readme.TXT
Non-standard fonts are not supported
ReturnEnter
MPEG4
Off
Menu
Changing the Camera Angle
When a DVD contains multiple angles of a particular scene, you can use the ANGLE function.
Using the ANGLE function (DVD)
If the disc contains multiple angles, the ANGLE appears on the screen.
1. During play or pause mode, press the MENU button on the remote control.
2. Press the
3. Press the π/ buttons to select Angle, then press the
4. Press the on the remote control to select the desired angle.
π/†
®
or ENTER button.
®
or ENTER button.
/®
buttons to select Function, then press the
Info Zoom Bookmark EZ View
Angle
buttons or you can use the number buttons
4/6
Note
- If the disc has only one angle, this feature won’t work. Currently, very few discs have this feature.
- Depending on the disc, these functions may not work.
Using the Bookmark Function
This feature lets you bookmark sections of a DVD so you can quickly find them at a later time.
Using the Bookmark Function (DVD)
1. During play, press the MENU button on the remote control.
2. Press the π/ buttons to select Function, then press the
®
or ENTER button.
Info Zoom
Bookmark
EZ View Angle
3. Press the π/† buttons to select Bookmark, then press the
®
or ENTER button.
4. When you reach the scene you want to mark, press-the
1 - -
CANCEL
1 2 3
CANCEL
1 2 3
CANCEL
- - -
ENTER button. Up to three scenes may be marked at a time.
ADVANCED FUNCTIONS
Note
- Depending on a disc, the Bookmark function may not work.
Recalling a Marked Scene
1~3. The first 1~3 steps are the same as those for “Using the Bookmark Function”.
/®
4. Press the
buttons to select a marked scene.
5. Press the PLAY () button to skip to the marked scene.
Clearing a Bookmark
1~3. The first 1~3 steps are the same as those for “Using the Bookmark Function”.
4. Press the
/®
buttons to select the bookmark number you
want to delete.
5. Press the CANCEL button to delete a bookmark number.
Using the Zoom Function
Using the Zoom Function (DVD)
1. During play or pause mode, press the MENU button on the remote control.
2. Press the
3. Press the
4. Press the screen you want to zoom in-on. Press the ENTER button.
- During DVD play, press ENTER to zoom in 2X/4X/2X/Normal in order.
π/†
®
or ENTER button.
π/†
®
or ENTER button.
π/
buttons to select Function, then press the
buttons to select Zoom, then press the
or
/®
buttons to select the part of the
Info
Zoom
Bookmark EZ View Angle
MenuReturnEnter
Clips Menu for MP3/WMA/ JPEG/ MPEG4/CD Audio
CD Audio or discs with MP3/WMA/JPEG/MPEG4 contain individual songs and/or pictures that can be organized into folders as shown below. They are similar to how you use your computer to put files into different folders.
Stop
Open the disc tray. Place the disc on the tray. Close the tray.
WMA
JPEG
MP3
MPEG4
The tray closes and this screen displays.
-
: Name of currently playing file.
-
: Current Playback Time.
-
: Current Playback Mode : There are four
modes. They can be selected in order by
Enter Return
pressing the REPEAT button.
- Off: Normal Playback
- Track: Repeats the current track.
- Folder: Repeats the current folder
- Random: Files in the disc will be played in random order.
-
: MP3 file icon. - : CD Audio file icon.
-
: WMA file icon. - : Folder icon.
-
: JPEG file icon - : Current Folder icon.
-
: AVI file icon.
Note
- When playing MP3, WMA or JPEG, the Picture Quality and the HDMI Resolution cannot be set.
- When playing MPEG4 file, the VIDEO SEL. only work in stop mode.
Off
00:00:00
T
T
Menu
English _21
advanced functions
Folder Selection
The folder can be selected both in Stop or Play mode.
- To select the Parent Folder Press the RETURN button to go to parent folder, or press
π/
the parent folder.
- To select the Peer Folder
Press the press ENTER.
- To select the Sub-Folder
Press the then press ENTER.
buttons to select “..” and press ENTER to go to the
π/
buttons to select the desired folder, then
π/
buttons to select the desired folder,
Root
WMA
JPEG
MP3
SONG FILE 3
MPEG4 FILES
MUSIC
1st
2nd
SONG FILE 1
SONG FILE 2
Parent Folder
Current Folder
Sub-Folders
Peer Folders
MP3/WMA/CD Audio Playback
1.
Open the disc tray. Place the disc on the tray. Close the tray.
- Only one kind of file is played back when a disc or a folder contains both MP3 and WMA files.
2. Press the Press ENTER to begin playback of the song file.
π/
or
/®
buttons to select a song file.
Play
Because You
...
Because You
Cactus
Sad Dayu
Wonderful
Off
00:00:23
T
T
Return
REPEAT
Repeat
Enter
Repeat/Random playback
Press the REPEAT button to change the playback mode. There are four modes, such as Off, Track, Folder and Random.
- Off: Normal Playback
- Track: Repeats the current song file.
- Folder: Repeats the song files which have the same extension in the current folder.
- Random: Song files which have the same extension will be played in random order.
To resume normal play, press the CANCEL button.
CD-R MP3/WMA file
When you record MP3 or WMA files on CD-R, please refer to the following.
Your MP3 or WMA files should be ISO 9660 or JOLIET format.
-
ISO 9660 format and Joliet MP3 or WMA files are compatible with Microsoft's DOS and Windows, and with Apple's Mac. This format is the most widely used.
- When naming your MP3 or WMA files, do not exceed 8 characters, and enter “.mp3, .wma” as the file extension.
General name format : Title.mp3. or Title.wma. When composing your title, make sure that you use 8 characters or less, have no spaces in the name, and avoid the use of special characters including: (.,/,\,=,+).
- Use a decompression transfer rate of at least 128 Kbps when recording MP3 files.
Sound quality with MP3 files basically depends on the rate of compression/decompression you choose. Getting CD audio sound requires an analog/digital sampling rate, that is
conversion to MP3 format, of at least 128 Kbps and up to 160 Kbps. However, choosing higher rates, like 192 Kbps or more,
only rarely give better sound quality. Conversely, files with
decompression rates below 128 Kbps will not be played properly.
- Use a decompression transfer rate of at least 64Kbps when recording WMA files.
Sound quality with WMA files basically depends on the rate of compression/decompression you choose. Getting CD audio sound requires an analog/digital sampling rate, that is conversion to WMA format, of at least 64Kbps and up to 192Kbps. Conversely, files with decompression rates below 64Kbps or over 192Kbps will not be played properly. Sampling rate that can be supported for WMA files is > 30Khz.
- Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected to prevent illegal copying. These files are of the following types: Windows Media Inc) and SDMITM (registered trade mark of The SDMI Foundation). You cannot copy such files.
- Important:
The above recommendations cannot be taken as a guarantee that the DVD player will play MP3 recordings, or as an assurance of sound quality. You should note that cer tain technologies and methods for MP3 file recording on CD­ Rs prevent optimal playback of these files on your DVD player (degraded sound quality and in some cases, inability of the player to read the files).
This unit can play a maximum of 500 files and 500 folders per disc.
-
TM
(registered trade mark of Microsoft
22_ advanced functions
...
Because You
Cactus
Sad Dayu
Wonderful
Sweet Vol 3
Sweet Vol 3
00:00:20
Enter
Return
T
T
Menu
...
a01_divx51b-8
a02_divx505b-8
a03_divx502sp-8
a04_divx412-8
/a01_divx51b-8
00:00:00
Enter Return
T
T
Menu
ReturnEnter
...
a01_divx51b-8
a02_divx505b-8
a03_divx502sp-8
a04_divx412-8
/MPEG4
00:00:00
Enter Return
T
T
Menu
MPEG4 Playback
MPEG4 Play Function
AVI files are used to contain the audio and video data. Only AVI format files with the “.avi” extensions can be played.
1. Open the disc tray. Place the disc on the tray. Close the tray.
2. Press the
(DivX/XviD) and then press ENTER button.
π/
or
/®
buttons to select an avi file
Stop
Off
CD-R AVI file
This unit can play the following video compression formats within the AVI file format:
- DivX 3.11 contents
- DivX 4 contents (Based on MPEG-4 Simple Profile)
- DivX 5 contents (MPEG-4 simple profile plus additional features such as bi-directional frames. Qpel and GMC are also supported.)
- XviD MPEG-4 compliant Contents.
DVD-RW & DVD+R
Format that support for DivX file :
- Basic DivX format DivX3.11 / 4.12/ 5.x
- Xvid (MPEG-4 compliant video codec) and DivX Pro
- File format : *.avi, *.div, *.divx.
This unit supports all resolutions up to maximum below.
ADVANCED FUNCTIONS
Repeat and Repeat A-B playback
Press the REPEAT button to change playback mode. There are 3 modes, such as Off, Folder and Title.
- Folder : repeats the AVI files which have the same extension in the current folder.
- Title : repeats the title that is playing.
Press the REPEAT A-B button to set the point where you want repeat play to start (A). Press the REPEAT A-B button again at the point where you want the repeat play to stop (B).
- To return to normal play, press the CANCEL button.
Note
- A-B REPEAT does not allow you to set point (B) until at least 5 second of playback time has elapsed after point (A) has been set
MPEG4 Function Description
Function Description Reference page
During play, press the |k or
Skip
(|k or K|)
Search
(k or K)
Slow Motion
Play
Step Motion
Play
ZOOM
button, it moves forward
K|
or backward 5 minutes. During play, press the SEARCH
k or K
) button and press
( again to search at a faster speed.
Allows you to search at a faster speed in an AVI file. (2X, 4X, 8X)
Allows you to search at a slower speed in an AVI file. (1/2X, 1/4X, 1/8X)
Each time the STEP button is pressed, a new frame will appear.
2X/4X/2X/Normal in order
-
-
P 16
P 16
P 21
DivX3.11 & DivX4 & XviD DivX5
Bitrate may fluctuate: Device may skip decoding the high bitrate portions
720 x 480 @30fps 720 x 576 @25fps
: Maximum bitrate : 4Mbps and begin decoding again when Bitrate returns to normal.
Possible warning messages that may appear when trying to play DivX/AVI files are :
1. No Authorization
- File with bad registration code.
Authorization Error
This player is not authorized
to play this video.
OK
2. Unsupported Codec
- Files with certain Codec Types, Versions (ex. MP4, AFS and other proprietary codecs) are not suppoerted by this player.
Stop
File you attempt to play has unsupported codec
Off
3. Unsupported Resolution
- Files containing resolutions higher than the player’s specification are not supported.
Stop
Off
- These functions may not work depending on MPEG4 file.
File you attempt to play has unsupported resolution
English _23
advanced functions
Enter Return
Menu
USB
Note
• The resolution that can be supported by DVD­1080P9 model up to 720 x 480 @30 frames/ 720 x 576 @25 frames
• This unit supports CD-R/RW written in MPEG4 in accordance with the “ISO9660 format”.
Playing Media Files Using the USB Host feature
You can enjoy the media files such as pictures, movies and tunes saved in an MP3 player, USB memory or digital camera in high audio by connecting the storage device to the USB port of the DVD Player.
Using the USB HOST feature
1.
Connect the USB device to the USB port on the front of the unit.
2. Press the USB button, Press the
π/
button to
select the one of partision from USB, then Press ENTER.
Disc
3. Press the
π/
or
/®
buttons to select a file in USB.
Press ENTER to Open file.
Stop
Note
Each time the USB button on the remote control is
• pressed, a frame of the USB device selection will appear.
USB” appears on the display screen.
USB MENU screen appears on the TV screen and the
• saved file is played.
Safe USB Removal
To prevent damage to the memory stored in the USB device, perform safe removal before disconnecting the USB cable.
- Press the STOP () button
- Remove the USB cable.
Skip Forward/Back
During playback, press the
When there is more than one file, when you press the K|
• button, the next file is selected. When there is more than one file, when you press the |k
• button, the previous file is selected
(
|k/K|
.
)
button.
24_ advanced functions
Fast playback
To play back the disc at a faster speed, press
(
k/K
) d
Each time you press either button, the playback speed will
uring playback.
change as follows : 2x 4x 8x.
Compatible Devices
1. USB devices that support USB Mass Storage v1.0. (USB devices that operate as a removable disk in Windows (2000 or later) without additional driver installation.)
2. MP3 Player: Flash type MP3 player.
3.
Digital camera: Cameras that support USB Mass Storage v1.0.
• Cameras that operate as a removable disk in Windows (2000 or later) without additional driver installation.
4. USB Flash Drive: Devices that support USB2.0 or USB1.1.
• You may experience a difference in playback quality when you connect a USB1.1 device.
5. USB card Reader: One slot USB card reader and Multi slot USB card reader
• Depending on the manufacturer. the USB card reader
may not be supported.
If you install multiple memory devices into a multi card
reader, you may experience problems.
6. If you use a USB extension cable, the USB device might not be recognized.
Supported Formats
File
File
Bit
Name
extension
Still
JPG
WMA
WMV
JPG .JPEG
.MP3
.WMA
MPG.MPEG
.WMV
.AVI, .ASF
80~384kbps
56~128kbps
MP3
VCD
DivX
Picture
Off
Music
Movie
Rate
-
1.5Mbps
4Mbps
4Mbps
Version Pixel
-
-
V8
VCD1.1,VCD2.0
V1,V2,V3,V7
.DivX3.11~DivX5.1,Xvid
640*480
320*480
720*480
720*480
-
-
Sampling
Frequency
-
44.1KHz
44.1KHz
44.1KHz
44.1KHz~48KHz
44.1KHz~48KHz
Note
• VCD & WMV can't be played on this player.
• CBI (Control/Bulk/Interrupt) is not supported.
• Digital Cameras that use PTP protocol or require additional
program installation when connected to a PC are not supported.
• A device using NTFS file system is not supported.
(Only FAT 16/32 (File Allocation Table 16/32) file system is supported.)
• Some MP3 players, when connected to this product,may not
operate depending on the sector size of their file system.
• The USB HOST function is not supported if a product that
transfers media files by its manufacturer-specific program is connected.
• Does not operate with Janus enabled MTP(Media Transfer
Protocol) devices.
• The USB host function of this product does not support all
USB devices.
00:00:00
Enter
T
T
Menu
Track 01
Track 02
Track 03
Track 04 Track 05
Track 06
Track 07
Track 08
Track 01
USB
00:00:00
Enter
T
T
Track 01
Track 02
Track 03
Track 04 Track 05
Track 06
Track 07
Track 08
Track 01
REPEAT
Repeat
CANCEL
00:00:00
Enter
T
T
Menu
Track 01
Track 02
Track 03
Track 04 Track 05
Track 06
Track 07
Track 08
Track 01
ENTER RETURN
ENTER
RETURN
CD Ripping
This feature lets you to copy audio files from disc to USB device into MP3 format.
Open the dics tray.
Place the Audio CD(CD DA) disc on the tray, and close the tray.
Connect the USB device to the USB port on the front of the unit.
This screen will displayed.
Stop
DEV : ­SELECT ALL START
Off
Picture CD Playback
1. Select the desired folder.
2. Press the menu and then press the ENTER button.
3. Press the INFO button on the remote control to select the menu you want to view and then press the ENTER button.
π/
buttons to select a Picture file in the clips
ADVANCED FUNCTIONS
1. With the unit in Stop mode, press the ® button to select the DEV (storage media device) menu, then press ENTER but- ton.
2. Press the
π/
buttons to select SELECT, then press the
ENTER button to marked all files to be copying.
- To unmarked copying all files press ENTER button again.(UNSELECT Menu)
-
If you want to marked several files to be copying, press the
button, then press ENTER button on the selected file.
Stop
Disc
3. Press the
ENTER button.
π/
buttons to select START,-then-press the
File copy begins.
- To cancel the copying in progress, press the CANCEL button.
Play
CD Ripping START
Cancel Ripping
Note
- When the CD ripping being processed the player will automatic in play mode.
- Only the Audio CD(CD DA) dics can be ripping.
Off
DEV : ­SELECT ALL START
DEV : USB 1 UNSELECT ALL
Note
- Press the STOP button to return to the clips --menu.
- When playing a Kodak Picture CD, the unit displays the Photo directly, not the clips menu.
- HD-JPEG must be set to SD
Rotation
: Each time the ENTER button is pressed, the
picture rotates 90 degrees clockwise.
Zoom
: Press the
π/
buttons to select the part of the
screen you want to zoom in on.
Press the ENTER button. Each time the ENTER but-
ton is pressed, the picture is enlarged up to 2X.
Slide Show
: The unit enters slide show mode.
• Before beginning the Slide Show, the picture interval must be set.
: When this icon is selected and ENTER is
Off
pressed, the pictures change automatically with about a 6 second interval.
: The pictures change automatically with
about a 12 second interval.
: The pictures change automatically with
about a 18 second interval.
TIMER :
Note
- Depending on a file size, the amount of time between each picture may be different from the manual.
- If you don’t press any button, the slide show will start automatically in about 10 seconds by default.
English _25
advanced functions
Picture CD Playback for HD-JPEG
Must connect to HDMI. Resolution should be 720p/1080i/ 1080p, and HD-JPEG should be in HD mode.
"Please set the HDMI as highest Resolution which you TV support."
1. Select the desired folder.
2. Press the π/ buttons to select a Picture file in the clip menu and then press the ENTER button.
Press the STOP () button to return to the clips menu.
When playing a Kodak Picture CD, the unit displays the
Photo directly, not the clips menu.
Note
- To make the setup menu disappear, press the MENU button.
Rotation Press the √/® button to rotate the screen 90 degrees to the left/right.
Skip Picture Press the |k or K| button to select previous or next picture.
Slide Show Press the PLAY (® ) button to start SLIDE function. Press the STOP () button to stop SLIDE function.
Stop
WMA
JPEG
MP3
MPEG4
Stop
1
2
3
1
...
Enter Return
ReturnEnter
Off
00:00:00
T
T
Menu
Off
00:00:00
Menu
Note
- Depending on a file size, the amount of time between each picture may be different from the set interval time.
- The image may be displayed at a smaller size depending on the picture size when displaying images in HD-JPEG mode.
- It is recommended to set the "BD Wise" to "Off" In case of playback JPEG image file bigger than 720 X 480 pixel size.
MP3-JPEG Playback
You can play JPEG using music as a backgound.
Press the
π/
1.
buttons to select an MP3 file in the clips
menu and then press the ENTER button.
2.
Press the
π/
buttons to select a JPEG file in the
clips menu and then press the ENTER button.
- Music willplay from the beginning
3. Press Stop button when you want to stop the playback.
Note
MP3 and JPEG files have to be on the same disc.
CD-R JPEG Disc
- Only files with the “.jpg” and “.JPG” extensions can be played.
- If the disc is not closed, it will take longer to start playing and
not all of the recorded files may be played.
- Only CD-R discs with JPEG files in ISO 9660 or Joliet format
can be played.
- The name of the JPEG file may not be longer than 8
characters and should contain no blank spaces or special characters (. / = +).
- Only a consecutively written multi-session disc can be played.
If there is a blank segment in the multi-session disc, the disc can be played only up to the blank segment.
- A maximum of 500 images can be stored on a single CD.
- Kodak Picture CDs are recommended.
- When playing a Kodak Picture CD, only the JPEG files in the
pictures folder can be played.
- Kodak Picture CD: The JPEG files in the pictures folder can
be played automatically.
- Konica Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- Fuji Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- QSS Picture CD: The unit may not play QSS Picture CD.
- If the number of files in 1 Disc is over 500, only 500 JPEG
files can be played.
- If the number of folders in 1 Disc is over 500, only JPEG
files in 500 folders can be played
26_ advanced functions
MenuReturnEnter
Enter
Return Menu
MenuReturnEnter
changing setup menu
Using the Setup Menu
The Setup menu lets you customize your DVD player by allowing you to select various language preferences, set up a parental level, even adjust the player to the type of television screen you have.
1. With the unit in Stop mode, press the MENU button on the
π/
remote control. Use the
®
press the
Language Setup: Setup of the Language.
Audio Setup : Setup of the Audio Options.
Display Setup : Setup of the Display Options. Use to
or ENTER button.
buttons to select Setup, then
Language Setup ® Audio Setup ® Display Setup ® Parental Setup : DivX(R) Registration ® Anynet+(HDMI-CEC) : On
select which type of screen you want to watch and several display options.
Parental Setup :-Setup of the Parental Level.
Allows users to set the level necessary to prevent children from viewing unsuitable movies such as those with violence, adult subject matter, etc.
DivX(R) Registration : Please use the Registration
code to register this player with the DivX(R) Video On Demand format. To learn more go to www.divx.com/vod.
Anynet+(HDMI-CEC): Setup of the Anynet+(HDMI-CEC)
Options.
π/
2. Press the Press the
buttons to access the different features.
®
or ENTER button to access the sub features.
3. To make the setup screen disappear after setting up, press the MENU button again.
Note
Depending on the disc, some Setup Menu selections may not work.
If you set the player menu, disc menu, audio and subtitle language in advance, they will come up automatically every time you watch a movie.
Using the Player Menu Language
1. With the unit in Stop mode, press the MENU button.
2. Press the or ENTER button.
3. Press the press the
4. Press the
®
the
5. Press the then press the
- The language is selected and the screen returns to Language Setup menu.
- To make the setup menu disappear, press the MENU button.
Using the Disc Menu Language
This function changes the text language only on the disc menu screens.
1. With the unit in Stop mode, press the MENU button.
2. Press the or ENTER button.
3. Press the press the
4. Press the the
5. Press the then press the
- If the selected language is not recorded on the disc, the original pre-recorded language is selected.
- The language is selected and the screen returns to Language Setup menu.
- To make the setup menu disappear, press the MENU button.
Setting Up the Language Features
π/
buttons to select Setup, then press the ®
π/
buttons to select Language Setup, then
®
or ENTER button.
π/†
®
®
buttons to select Player Menu, then press
or ENTER button.
π/
buttons to select the desired language,
®
or ENTER button.
Player Menu
Disc Menu Audio Subtitle DivX Subtitle
π/
buttons to select Setup, then press the ®
π/
buttons to select Language Setup, then
®
or ENTER button.
π/
buttons to select Disc Menu, then press
or ENTER button.
π/
buttons to select the desired language,
®
or ENTER button.
Player Menu
Disc Menu
Audio Subtitle DivX Subtitle
LANGUAGE SETUP
English Français Deutsch Español Italiano Nederlands
LANGUAGE SETUP
English Français Deutsch Español Italiano Nederlands
CHANGING SETUP MENU
English _27
changing setup menu
MenuReturnEnter
MenuReturnEnter
MenuReturnEnter
MenuReturnEnter
MenuReturnEnter
Using the Audio Language
1. With the unit in Stop mode, press the MENU button.
2. Press the
π/
buttons to select Setup, then press the ®
or ENTER button.
π/
3. Press the press the
4. Press the
buttons to select Language Setup, then
®
or ENTER button.
π/
buttons to select Audio, then press the ®
or ENTER button.
5. Press the press the
π/
buttons to select the desired language, then
®
or ENTER button.
- Select “Original” if you want the default soundtrack language to be the original language the disc is recorded in.
- If the selected language is not recorded on the disc, the original pre-recorded language is selected.
- The language is selected and the screen returns to Language Setup menu.
- To make the setup menu disappear, press the MENU button.
LANGUAGE SETUP
Player Menu
Original English
Disc Menu
Français
Audio
Deutsch
Subtitle
Español Italiano
DivX Subtitle
Using the Subtitle Language
1. With the unit in Stop mode, press the MENU button.
2. Press the or ENTER button.
3. Press the press the
4. Press the or ENTER button.
5. Press the then press the
- Select “Automatic” if you want the subtitle language to be the same as the language selected as the audio language.
- Some discs may not contain the language you select as your initial language; in that case the disc will use its original language setting.
- The language is selected and the screen returns to setup menu.
- To make the setup menu disappear, press the MENU button.
π/
buttons to select Setup, then press the ®
π/
buttons to select Language Setup,-then
®
or ENTER button.
π/
buttons to select Subtitle, then press the ®
π/
buttons to select the desired -language,
®
or ENTER button.
LANGUAGE SETUP
Player Menu Disc Menu Audio
Subtitle
DivX Subtitle
Automatic English Français Deutsch Español Italiano
Using the DivX Subtitle Language
1. With the unit in Stop mode, press the MENU button.
π/
2. Press the
buttons to select Setup, then press the ®
or ENTER button.
π/
3. Press the press the
4. Press the
®
the
5. Press the then press the
buttons to select Language Setup,-then
®
or ENTER button.
π/
buttons to select DivX Subtitle, then press
or ENTER button.
π/
buttons to select the desired language,
®
or ENTER button.
- The language is selected and the screen returns to Language Setup menu.
- To make the setup menu disappear, press the MENU button.
Player Menu Disc Menu Audio Subtitle
DivX Subtitle
LANGUAGE SETUP
Unicode Western Turkish Central Cyrillic Greek
Setting Up the Audio Options
Audio Options allows you to setup the audio device and sound status settings depending on the audio system in use.
1. With the unit in Stop mode, press the MENU button.
π/
2. Press the
or ENTER button.
3. Press the
®
the
4. Press the
press the
buttons to select Setup, then press the ®
π/
buttons to select Audio Setup, then press
or ENTER button.
π/
buttons to select the desired item, then a
®
or ENTER button.
Language Setup ®
Audio Setup ®
Display Setup ® Parental Setup : ® DivX(R) Registration ® Anynet+(HDMI-CEC) : On
Digital Out : PCM
MPEG-2 Digital Out : PCM Dynamic Compression : On PCM Down Sampling : On Power On Music : On
AUDIO SETUP
28_ changing setup menu
MenuReturnEnter
Digital Out
- PCM : Converts to PCM(2CH) audio. Bitstream : Outputs Dolby Digital via the digital output.
-
Select Bitstream when connecting to a Dolby Digital
Decoder.
MPEG-2 Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Converts to MPEG-2 Digital Bitstream
(5.1CH). Select Bitstream when using the Digital Audio Output.
Dynamic Compression
- On : To select dynamic compression.
- Off : To select the standard range.
PCM Down Sampling
- On : Select this when the Amplifier connected to the
player is not 96KHz compatible. In this case, the 96KHz signals will be down converted to 48KHZ.
- Off : Select this when the Amplifier connected to the
player is 96KHz compatible. In this case, all signals will be output without any changes.
Note :
- There is no analog audio output when you play a DTS sound disc.
- Even when PCM Down sampling is Off
• Some discs will only output down sampled audio through the digital outputs.
• To make the Setup menu disappear, press the MENU button
Power On Music This menu is used to activate or deactivate the opening sound when you turn on the DVD player.
- On : To turn On Start up music.
- Off : To turn Off Start up music
HDMI
- If your TV is not compatible with compressed multi­channel formats (Dolby Digital, DTS, MPEG), you should set Digital Audio to PCM.
- If your TV is not compatible with LPCM sampling rates over 48kHz, you should set PCM Down sam­pling to On.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
Setting Up the Display Options
Display options enable you to set various video functions of the player.
1. With the unit in Stop mode, press the MENU button.
π/
2. Press the or ENTER button.
3. Press the
®
the
4. Press the press the
buttons to select Setup, then press the ®
π/
buttons to select Display Setup, then press
or ENTER button.
π/
buttons to select the desired item, then
®
or ENTER button.
Language Setup ® Audio Setup ®
Display Setup ®
Parental Setup : DivX(R) Registration ® Anynet+(HDMI-CEC) : On
TV Aspect
Depending on a type of television you have, you may want to adjust the screen setting (aspect ratio).
- 4:3 Letter Box : Select when you want to see the total 16:9 ratio screen DVD supplies, even though you have a TV with a 4:3 ratio screen. Black bars will appear at the top and bottom of the screen.
- 4:3 Pan&Scan : Select this for conventional size TVs when you want to see the central portion of the 16:9 screen. (Extreme left and right side of movie picture will be cut off.)
- 16:9 Wide : You can view the full 16:9 picture on your wide screen TV.
DISPLAY SETUP
TV Aspect
4:3 Letter Box
Screen Messa
4:3 Pan&Scan
TV System
16:9 Wide
Video Output HDMI ® Picture Quality ®
Screen Messages
Use to turn on-screen messages On or Off.
TV System
- NTSC : In case of using NTSC disc
• If your TV system only has PAL-Video input, you must choose “PAL”. When you choose “PAL”, Interlace out­put format is PAL 60 Hz output.
• If your TV system only has NTSC, input you must choose “NTSC ”.
• If you set up the NTSC TV, HDMI output frame rate is 60 Hz.
- PAL : In case of using PAL disc
• If your TV system only has NTSC-Video input, you must choose “NTSC”.
• If your TV system only has PAL input, you must choose “PAL ”.
• If you set up the PAL TV, HDMI output frame rate is 50 Hz.
- Auto
DISPLAY SETUP
TV Aspect : Wide Screen Messages : On
TV System
Video Output HDMI Picture Quality ®
English _29
NTSC PAL Auto
®
CHANGING SETUP MENU
MenuReturnEnter
MenuReturnEnter
changing setup menu
MenuReturnEnter
MenuReturnEnter
MenuReturnEnter
MenuReturnEnter
Video Output
Select Video Output.
- I-SCAN : Select when you want to use Component Interlace Out.
- P-SCAN : Select when you want to use Component Progressive Out.
SCART-
RGB : Select when you want to use SCART
­RGB Out. (
- SCART-CVBS : Select when you want to CVBS output from scart connection. (
mode.)
• If you press the VIDEO SEL. button, Video output
• If the Yes/No selection in the Display Setup sub
It does not function in NTSC mode.)
It does not function in NTSC
mode is changed in regular sequence in no disc mode. (I-SCAN P-SCAN SCART-RGB SCART-CVBS)
Menu is not made within 10 seconds, the screen returns to the previous menu.
Setting Up the BD Wise
When the player is connected to a SAMSUNG TV which supports “BD Wise”,you can enjoy optimized Picture Quality by setting the “BD Wise” function as “On”.
1. With the unit in Stop mode, press the MENU button.
2. Press the or ENTER button.
3. Press the the
4. Press the the
5. Press the
Press the ENTER button.
π/
π/
®
or ENTER button.
π/†
®
or ENTER button.
π/†
®
or ENTER button.
π/
buttons to select Setup, then press the ®
buttons to select Display Setup, then press
buttons to select HDMI, then press
buttons to select BD-Wise, then press the
buttons to select On, then press the ® or
Resolution Setting : Auto
Resolution : 576p HD-JPEG : SD
BD-Wise : Off
HDMI SETUP
Off On
DISPLAY SETUP
TV Aspect : Wide Screen Messages : On TV System : Auto
I-SCAN
Video Output
P-SCAN
HDMI
SCART-RGB
Picture Qualit
SCART-CVBS
MenuReturnEnter
HDMI
This setting is used when the unit is connected by HDMI with Display devices (TV, projector, etc).
- Resolution Setting
- Auto : Resolution setting automatically
- Manual : Resolution setting manually
- Resolution
- 480p/576p : 720 x 480, 720 x 576
- 720p : 1280 x 720
- 1080i : 1920 x 1080
- 1080p : 1920 x 1080
- HD-JPEG
• HD : High Definition image source
- Available when resolution is 720p/1080i in HDMI enabled.
• SD : Standard Definition image source.
-
BD-Wise
Resolution Setting : Auto
Resolution : 576p HD-JPEG : SD
BD-Wise : Off
HDMI SETUP
Resolution Setting : Auto
Resolution : BD-Wise HD-JPEG : SD
BD-Wise : On
HDMI SETUP
Note
This option can be changed only when TV support BD Wise
How to turn Off the BD Wise
If you wish to changed to other resolution when "BD Wise On", Please choose a method between these two as follows :
Method 1
1. With the unit in Stop mode, press the MENU button.
2. Press the or ENTER button.
3. Press the the
4. Press the the
5. Press the then press the
π/
buttons to select Setup, then press the ®
π/†
®
®
buttons to select Display Setup, then press
or ENTER button.
π/
buttons to select HDMI, then press
or ENTER button.
π/
buttons to select resolution you wish to use,
®
or ENTER button.
Resolution Setting : Manual
Resolution : BD Wise
HD-JPEG : SD
BD-Wise : On
HDMI SETUP
576P 720p 1080i 1080p
BD Wise
30_ changing setup menu
Please choose "Yes" to continue, otherwise choose "No" to keep current setting.
Loading...
+ 132 hidden pages