Samsung DV457EVGSGRAA, DV457, DV457EVGSGR, DV457GVGSWR, DV457GVGSWRAA User Manual

...

DV457E(G)*

Gas and Electric Dryer

user manual

This manual is made with 100% recycled paper.

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service or accessory

parts, please register your product at or contact

www.samsung.com/register

1-800-SAMSUNG (726-7864)

DV457E(G)-02836E-03_EN.indd 1DV457E(G)-02836E-03_EN.indd 1 2012-12-04  6:44:292012-12-04  6:44:29

Features

Your new dryer will change the way you feel about drying laundry. From its specialized 8” LCD touch screen, and its innovative Smart Control technology to its time and energy e ciency, your new Samsung dryer has all the beneﬁ ts to make drying laundry as easy and pleasant as possible.

• Extra Large Capacity

Ultra drying capabilities at your ﬁ ngertips! Now you can dry extra-large loads. Our ultra large

7.5 cu.ft. capacity dryer circulates more air through your clothes, drying them faster, for a wrinkle-free result.

• 8” LCD Touch Screen Display

The brilliant 8” Color LCD Touch Screen displays cycle information, settings, options, and more. The easy-to-use interface allows you to scroll through all the drying cycles with the slightest touch.

• Smart Control (Elec. Model Only)

Samsung’s innovative Smart Control technology enables you to control your dryer through personal technology devices such as smart phones. You don’t have to be on standby until the cycle ends. The Smart Control allows you to monitor the drying process and lets you know when the cycle is complete.

• Smart Monitor (Gas Model Only)

Samsung’s innovative Smart Monitor technology enables you to monitor your dryer through personal technologies such as smart phones. You don’t have to be on standby until the cycle ends. Smart Monitor allows you to monitor the drying process and lets you know when the cycle is complete.

• Smart Care

Samsung’s Smart Care, an automatic error-monitoring system, detects and diagnoses problems at an early stage and provides quick and easy solutions through the LCD navigation. With the innovative Smart Control technology, you can also be alerted via your smart phone when a problem occurs.

• Steam Cycle

This cycle sprays a small amount of water into the drum of the dryer after several minutes of tumbling with heat. It reduces bad odors from clothing that are di cult to remove when washing with water and also reduces wrinkles.

• Sanitize Cycle

This cycle sanitizes garments by infusing high temperature heat deep into the fabric during the drying cycle and eliminating 99.9% of certain bacteria. Use this cycle for clothing, bedding, towels, or other items needing sanitization. The Sanitize cycle is certiﬁ ed by NSF International, an independent third-party testing and certiﬁ cation organization.

NSF Protocol P154

Sanitization Performance of

Residential Clothes Dryers

• Vent Sensor

Your Samsung dryer is equipped with a Vent Sensor which detects and notiﬁ es you when it is time to clean the ducts. Keep your dryer safe and e cient!

2_ Features

DV457E(G)-02836E-03_EN.indd Sec9:2DV457E(G)-02836E-03_EN.indd Sec9:2 2012-12-04  6:44:372012-12-04  6:44:37

• Time Saving

Our cycles are designed with you in mind. All our dryers are designed to dry your clothes quickly... just 42 minutes! Giving you time for more important things in life.

• Energy Saving

Your Samsung dryer is super energy e cient. You can dry up to 3.31 pounds of laundry with 1 kWh. Also, it saves energy by automatically drying your clothes the most e cient way.

• Easy Reversible Door

Your Samsung dryer will ﬁ t just about anywhere and without a door issues. The direction of its easy reversible door can be changed quickly and easily.

• Pedestal with Storage Drawers

An optional 15” pedestal is available to raise the dryer for easier loading and unloading. It also o ers a built-in storage drawer that can hold a 100 oz. bottle of detergent.

We strongly recommend that you DO NOT stack Samsung washers and dryers. It may be hard to view and use the dryer LCD control panel because of the viewing angle.

• 4-way Vent (Electric models only: DV457E*)

You can install the exhaust vent in the following four (4) positions: back, either side or at the bottom.

Features _3

DV457E(G)-02836E-03_EN.indd Sec9:3DV457E(G)-02836E-03_EN.indd Sec9:3 2012-12-04  6:44:372012-12-04  6:44:37

Safety instructions

Congratulations on your new Samsung Dryer. This manual contains important information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many beneﬁ ts and features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Please read this manual thoroughly to ensure that you know how to operate the extensive features and functions of your new appliance safely and e ciently. Retain the manual in a safe place near the appliance for future reference. Use this appliance only for its intended purpose as described in this instruction manual. The Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, or operating your dryer.

Always contact your manufacturer about problems or conditions you do not understand.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

Hazards or unsafe practices that may result in severe personal injury, death and/or property damage. Follow the information in this manual to minimize

the risk of ﬁ re or explosion or to prevent property damage, personal injury, or

WARNING

CAUTION

death. Do not store or use gasoline or other ﬂ ammable vapors and liquids near this or

any other appliance.

Hazards or unsafe practices that may result in personal injury and/or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Note

These warning signs are here to prevent injury to you and others. Please follow them explicitly. After reading this section, keep it in a safe place for future reference.

SAVE THESE INSTRUCTIONS

4_ Safety instructions

DV457E(G)-02836E-03_EN.indd Sec11:4DV457E(G)-02836E-03_EN.indd Sec11:4 2012-12-04  6:44:372012-12-04  6:44:37

WARNING - Risk of Fire

• Clothes dryer installation must be performed by a qualiﬁ ed installer.

• Install the clothes dryer according to the manufacturer’s instructions and local codes.

• Do not install a clothes dryer with ﬂ exible plastic venting materials. If ﬂ exible metal (foil type) duct is installed, it must be of a speciﬁ c type identiﬁ ed by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct the clothes dryer’s airﬂ ow and increase the risk of ﬁ re.

• To reduce the risk of severe injury or death, follow all installation instructions.

TO REDUCE THE RISK OF FIRE OR EXPLOSION:

WARNING

• Do not dry items that have been previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning solvents, or other ﬂ ammable or explosive substances. They emit vapors that could ignite or explode. Any material that has been in contact with a cleaning solvent or ﬂ ammable liquids or solids should not be placed in the dryer until all traces of these ﬂ ammable liquids or solids and their fumes have been removed. There are many highly ﬂ ammable items used in homes, such as acetone, denatured alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers, turpentine, waxes, and wax removers

• Do not dry items containing foam rubber (may be labeled latex foam) or similarly textured rubber-like materials on a heat setting. Heated foam rubber materials can, under certain circumstances, produce ﬁ re by spontaneous combustion.

WHAT TO DO IF YOU SMELL GAS:

WARNING

• Do not try to light any appliance.

• Do not turn on the appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Clear the room, building or area of all occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

• Installation and service must be performed by a qualiﬁ ed installer, service agency, or the gas supplier.

SAVE THESE INSTRUCTIONS

Safety instructions _5

DV457E(G)-02836E-03_EN.indd Sec11:5DV457E(G)-02836E-03_EN.indd Sec11:5 2012-12-04  6:44:382012-12-04  6:44:38

Safety instructions

IMPORTANT SAFTY INSTRUCTION

WARNING

To reduce the risk of ﬁ re, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following:

1. Read all instructions before using this appliance.

2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted

with gasoline, dry-cleaning solvents, or other ﬂ ammable or explosive substances, because they give o vapors that could ignite or explode.

3. Do not use the dryer to dry clothes which have traces of any ﬂ ammable substance, such

as vegetable oil, cooking oil, machine oil, ﬂ ammable chemicals, thinner, etc., or anything containing wax or chemicals, such as mops and cleaning cloths. Flammable substances may cause the fabric to catch ﬁ re by itself.

4. Do not store or use gasoline or other ﬂ ammable vapors and liquids near this or any other

appliance.

5. Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is

necessary when the appliance is used near children and pets.

6. Before the appliance is removed from service or discarded, remove the door to the drying

compartment to prevent children or animals from becoming trapped inside.

7. Do not reach into the appliance when the drum is moving.

8. Do not install or store this appliance where it will be exposed to the weather.

9. Do not tamper with the controls.

10. Do not repair or replace any part of the appliance or attempt any servicing unless speciﬁ cally

recommended in the user-maintenance instructions or published in the user-repair instructions that you understand and have the skills to carry out.

11. Do not use fabric softeners or products to eliminate static unless recommended by the

manufacturer of the fabric softener or product.

12. Clean the lint screen before or after each load.

13. Do not use heat to dry articles containing foam rubber or similarly textured rubber-like

materials.

14. Keep the area around the exhaust opening and surrounding areas free from lint, dust, and

dirt.

15. The interior of the dryer and exhaust duct should be cleaned periodically by qualiﬁ ed service

personnel.

16. Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking

oils may contribute to a chemical reaction that could cause a load to catch ﬁ re.

17. This appliance must be grounded. See “Electrical requirements” and ”Grounding” in the “Installing your dryer” section.

18. This appliance must be properly grounded. Never plug the power cord into a receptacle that is not grounded adequately and in accordance with local and national codes. Refer to installation instructions for grounding this appliance.

SAVE THESE INSTRUCTIONS

6_ Safety instructions

DV457E(G)-02836E-03_EN.indd Sec11:6DV457E(G)-02836E-03_EN.indd Sec11:6 2012-12-04  6:44:382012-12-04  6:44:38

19. Ensure pockets are free from small irregularly shaped hard objects and foreign material, i.e.

coins, knives, pins, etc. These objects could damage your dryer.

20. Gas leaks may occur in your system, resulting in a dangerous situation.

21. Gas leaks may not be detected by smell alone.

22. Gas suppliers recommend you purchase and install a UL-approved gas detector.

STATE OF CALIFORNIA PROPOSITION 65 WARNINGS:

WARNING

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the State of California to cause cancer, birth defects, or other reproductive harm, and requires businesses to warn of potential exposure to such substances.

This product contains a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm. This appliance can cause low-level exposure to some of the substances listed, including benzene, formaldehyde, and carbon monoxide.

Gas appliances may cause low-level exposure to some of the substances listed including benzene, formaldehyde, carbon monoxide, and soot; as a result of possible incomplete combustion of natural gas or LP fuels. Exposure to these substances can be minimized further by properly venting the dryer to the outdoors.

CAUTION

1. Do not sit on top of the dryer.

2. Because of continuing product improvements, Samsung reserves the right to change

speciﬁ cations without notice. For complete details, see the Installation Instructions packed with your product before selecting cabinetry, making cutouts, or beginning installation.

3. Do not wash clothing with large buckles, buttons, or other heavy metal or solid things.

4. Install and use in accordance with the manufacturer’s instructions.

5. Do not place items in your dryer that have been spotted or soaked with vegetable oil or

cooking oil. Even after being washed, these items may contain signiﬁ cant amounts of these oils.

6. Residual oil on clothing can ignite spontaneously. The potential for spontaneous combustion

increases when items containing vegetable oil or cooking oil are exposed to heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become hot enough to catch ﬁ re. Piling, stacking, or storing these kinds of items may prevent heat from escaping and can create a ﬁ re hazard.

7. All washed and unwashed fabrics that contain vegetable oil or cooking oil can be dangerous.

Washing these items in hot water with extra detergent will reduce, but not eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their temperature. Never remove these items from the dryer hot or interrupt the drying cycle until the items have run through the Cool Down cycle. Never pile or stack these items when they are hot.

8. Take care that children’s ﬁ ngers are not caught in the door when closing it. This may result in

injury.

SAVE THESE INSTRUCTIONS

Safety instructions _7

DV457E(G)-02836E-03_EN.indd Sec11:7DV457E(G)-02836E-03_EN.indd Sec11:7 2012-12-04  6:44:382012-12-04  6:44:38

Safety instructions

REGULATORY NOTICE

1. FCC Notice

FCC CAUTION:

CAUTION

Any changes or modiﬁ cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received including interference that causes

undesired operation.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

FCC STATEMENT:

This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a di erent circuit from that of the receiver.

• Consult the dealer or an experienced radio/TV technician for help.

FCC RADIATION EXPOSURE STATEMENT:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

SAVE THESE INSTRUCTIONS

8_ Safety instructions

DV457E(G)-02836E-03_EN.indd Sec11:8DV457E(G)-02836E-03_EN.indd Sec11:8 2012-12-04  6:44:382012-12-04  6:44:38

2. IC Notice

The term “IC” before the radio certiﬁ cation number only signiﬁ es that Industry Canada technical speciﬁ cations were met. Operation is subject to the following two conditions: (1) this device may

not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

For product available in the USA/Canada market, only channels 1~11 can be operated. Selection of other channels is not possible.

IC RADIATION EXPOSURE STATEMENT:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator & your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

SAVE THESE INSTRUCTIONS

Safety instructions _9

DV457E(G)-02836E-03_EN.indd Sec11:9DV457E(G)-02836E-03_EN.indd Sec11:9 2012-12-04  6:44:382012-12-04  6:44:38

Contents

INSTALLING YOUR DRYER

DRYING A LOAD OF LAUNDRY

12 Unpacking your dryer 12 The dryer exterior 13 Basic requirements 14 Ducting requirements 15 Important to installer 15 Location considerations 15 Alcove or closet installations 16 Mobile home installations 16 Exhausting 17 Gas requirements 17 Commonwealth of massachusetts

installation instructions

18 Electrical requirements 18 Grounding 19 Electrical connections 20 Connecting the inlet hose 22 Replacement parts and accessories 22 Installation 25 Final installation checklist 25 Dryer exhaust tips 26 Door Reversal 28 Setting up your dryer for the ﬁ rst time

30 Drying for the ﬁ rst time 30 Basic instructions 31 Using the control panel 36 Drying your laundry using the cycle

selection screen

45 Using the Rack Dry 45 Checking the ﬁ lter 46 Vent Sensor

USING YOUR MOBILE PHONE

10_ Contents

DV457E(G)-02836E-03_EN.indd Sec2:10DV457E(G)-02836E-03_EN.indd Sec2:10 2012-12-04  6:44:382012-12-04  6:44:38

47 Conﬁ guring your dryer’s network settings

and connecting to your network

48 Turning on the Wi-Fi networking function of

your dryer

49 How to update the software 50 Downloading and running the mobile app,

Samsung Smart Washer/Dryer App

51 Using the Mobile App 55 Overview of wi-ﬁ settings and ap connection

screens

CARE AND CLEANING

56 Control panel 56 Tumbler 56 Stainless steel tumbler 56 Dryer exterior 56 Dryer exhaust system

SPECIAL LAUNDRY TIPS

TROUBLESHOOTING

APPENDIX

57 Special laundry tips

58 Check these points if your dryer… 59 Information codes 61 Network Setup Q&A

63 Fabric care chart 64 Protecting the environment 64 Declaration of conformity 64 Speciﬁ cations 65 Cycle chart

Contents _11

DV457E(G)-02836E-03_EN.indd Sec2:11DV457E(G)-02836E-03_EN.indd Sec2:11 2012-12-04  6:44:382012-12-04  6:44:38

Installing your dryer

UNPACKING YOUR DRYER

Unpack your Dryer and inspect it for shipping damage. Make sure you have received all the items shown below. If your Dryer was damaged during shipping, or you do not have all the items, contact 1-800-SAMSUNG (726-7864).

To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit.

The packing materials can be dangerous to children. Keep all packaging material (plastic bags, polystyrene, etc.) well out of the reach of children.

WARNING

THE DRYER EXTERIOR

Top Cover

[ BACK ]

Control panel

Door

Filter

Frame Front

Parts supplied

“Y”-connector Short inlet hose Rubber Washer Long inlet hose

12_ Installing your dryer

Duct Exhaust

Water Inlet

DV457E(G)-02836E-03_EN.indd 12DV457E(G)-02836E-03_EN.indd 12 2012-12-04  6:44:382012-12-04  6:44:38

Tools needed

01 INSTALLING YOUR DRYER

Pliers Cutting knife

Level Phillips Screwdriver Duct tape Wrench

Pipe wrench

(gas only)

Nut drivers

BASIC REQUIREMENTS

Make sure you have everything necessary for the proper installation

• A GROUNDED ELECTRICAL OUTLET is required. Refer to the “Electrical requirements” section on page 18.

• A POWER CORD for electric dryers (except for Canada).

• GAS LINES (if you have a gas dryer) must meet national and local codes.

• The EXHAUST SYSTEM must be rigid metal or ﬂ exible sti -walled metal exhaust ducting.

Installing your dryer _13

DV457E(G)-02836E-03_EN.indd 13DV457E(G)-02836E-03_EN.indd 13 2012-12-04  6:44:382012-12-04  6:44:38

Installing your dryer

DUCTING REQUIREMENTS

• Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.

• Do not use a smaller duct.

• Ducts larger than 4 inches (10.2 cm) in diameter can result in increased accumulation of lint.

• Lint should be removed regularly.

• If a ﬂ exible metal duct must be used, use the type with a sti sheet metal wall. Do not use a ﬂ exible duct with a thin foil wall. A serious blockage can result if the ﬂ exible metal duct is bent too sharply.

• Never install any type of ﬂ exible duct in walls, ceilings, or other concealed spaces.

• Keep the exhaust duct as straight and short as possible.

• Secure joints with duct tape. Do not use screws.

• Do not use plastic ﬂ exible duct. Plastic ﬂ exible duct can kink, sag, be punctured, reduce airﬂ ow, extend drying times, and a ect dryer operation.

• Exhaust systems longer than recommended can extend drying times, a ect machine operations, and collect lint.

• The exhaust duct should end with an exhaust hood with a swing-out damper to prevent back drafts and entry of wildlife. Never use an exhaust hood with a magnetic damper.

• The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and the ground or other obstruction. The hood opening should point down.

• Never install a screen over the exhaust outlet.

• To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house or porch.

• If the exhaust duct must run through an unheated area, the duct should be insulated and slope slightly down towards the exhaust hood to reduce condensation and lint buildup.

• Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before cleaning.

• Check frequently to make sure the exhaust hood damper opens and closes freely.

• Check once per month, and clean at least once per year. Note: If your clothes are not getting dry, then check the ducting for obstructions.

• Do not exhaust the dryer into a wall, ceiling, crawl space, or concealed space of a building, gas vent, or any other common duct or chimney. This could create a ﬁ re hazard from the lint expelled by the dryer.

ELECTRIC AND GAS DRYER

Weather Hood Type

Recommended

Use only for short-run installation

No. of 90° elbows

0 1 2 3

* Do not use non-metallic ﬂ exible ducts.

Rigid Metallic Flexible*

24.4 m (80 ft.) 12.4 m (41 ft.)

20.7 m (68 ft.) 11.2 m (37 ft.)

17.4 m (57 ft.) 10.1 m (33 ft.)

14.3 m (47 ft.) 9.0 m (29 ft.)

4” (10 .16 cm)

22.6 m (74 ft.) 10.1 m (33 ft.)

18.9 m (62 ft.) 8.8 m (29 ft.)

15.5 m (51 ft.) 7.6 m (25 ft.)

12.5 m (41 ft.) 6.5 m (21 ft.)

2.5” (6.35 cm)

Rigid Metallic Flexible*

14_ Installing your dryer

DV457E(G)-02836E-03_EN.indd 14DV457E(G)-02836E-03_EN.indd 14 2012-12-04  6:44:392012-12-04  6:44:39

If the new dryer is installed into an existing exhaust system you must make sure:

• The exhaust system meets all local, state, and national codes.

• That a ﬂ exible plastic duct is not used.

• To inspect and clean all lint buildup from inside the existing duct.

• The duct is not dented or crushed.

• The exhaust hood damper opens and closes freely. The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0. This can be measured with the dryer running with a manometer at the point where the exhaust duct

connects to the dryer. A no-heat setting should be used. The dryer tumbler should be empty and the lint ﬁ lter clean.

IMPORTANT TO INSTALLER

Please read the following instructions carefully before installing the dryer. These instructions should be kept for future reference.

Remove the door from all discarded appliances to avoid the danger of a child being trapped and su ocating.

WARNING

LOCATION CONSIDERATIONS

The dryer should be located where there is enough space at the front for loading the dryer, and enough space behind for the exhaust system. This dryer is factory-ready for the rear exhaust option. To exhaust out the bottom, right or the left, use the accessory exhaust kit. Instructions are included with the kit. Make sure the room in which the dryer is located has enough fresh air. The dryer must be located where there are no air-ﬂ ow obstruction.

For gas dryers, adequate clearance must be maintained as noted on the data plate to ensure adequate air for combustion and the proper dryer operation.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. The dryer area must be kept clear of combustible materials, gasoline, and other ﬂ ammable vapors and liquids. A dryer produces combustible lint. The area around the dryer should be kept lint-free.

01 INSTALLING YOUR DRYER

ALCOVE OR CLOSET INSTALLATIONS

The dryer must be exhausted to the outside to reduce the risk of ﬁ re when installed in an alcove or closet.

WARNING

• No other fuel-burning appliance should be installed in the same closet as the dryer.

• WARNING: To reduce the risk of ﬁ re, this dryer must be exhausted to the outside. Refer to “Exhausting” section on page 16.

• Minimum clearances between the dryer and adjacent walls or other surfaces are: 2” in front, 17” on top, 1” on either side, and 5” at the back.

• The front of the closet must have two unobstructed air openings for a combined minimum total area of 72 in² with a minimum clearance of 3” at the top and bottom. A slatted door with equivalent space clearances is acceptable.

Installing your dryer _15

DV457E(G)-02836E-03_EN.indd 15DV457E(G)-02836E-03_EN.indd 15 2012-12-04  6:44:392012-12-04  6:44:39

Installing your dryer

MOBILE HOME INSTALLATIONS

The installation of the dryer in a mobile home must conform to the Manufactured Home Construction and Safety Standards Title 24 CFR, Part 3280 {formerly the Federal Standards for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada).

• When installing a dryer in a mobile home, provisions for anchoring the dryer to the ﬂ oor must be made.

• Locate an area with adequate fresh air.

• A minimum unobstructed space of 72 in² (465 cm²) is required.

• Call 1-800-SAMSUNG for information on purchasing the Floor Anchoring Kit as an accessory.

• All mobile home installations must be exhausted to the outside with the exhaust duct termination securely fastened to the mobile home structure, using materials that will not combust.

• The exhaust duct may not terminate underneath the mobile home.

• Refer to the following “Exhausting” section for more information.

EXHAUSTING

The dryer shall not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a building.

Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room.

See “Ducting requirements” in installing your dryer section for the maximum duct length and number of bends.

• All dryers must be exhausted to the outside.

• The duct must not be assembled with screws or other fastening means that extend into the duct and catch lint.

• The required exhaust duct is 4 inches (102 mm) in diameter.

• The total length of ﬂ exible metal duct shall not exceed 2.4 m (7.8 ft.).

In the United States:

• Use only those foil-type ﬂ exible ducts, if any, speciﬁ cally identiﬁ ed for use with the appliance by the manufacturer and that comply with the Outline for Clothes Dryer Transition Ducts, Subject 2158A, shall be used.

In Canada:

• Use only those foil-type ﬂ exible ducts, if any, speciﬁ cally identiﬁ ed for use with the appliance by the manufacturer.

Outside the U.S. and Canada:

• Refer to the local codes.

The dryer must be exhausted to the outside to reduce the risk of ﬁ re when installed in an alcove or closet.

WARNING

NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT. If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.

WARNING

Use only a metal exhaust duct that is non-ﬂ ammable to ensure containment of the exhaust air, heat, and lint.

16_ Installing your dryer

DV457E(G)-02836E-03_EN.indd 16DV457E(G)-02836E-03_EN.indd 16 2012-12-04  6:44:392012-12-04  6:44:39

GAS REQUIREMENTS

Use only natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP (liquid propane) gas, it must be converted for safe and proper performance by a qualiﬁ ed service technician.

A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-o valve be installed within 6” of your dryer.

Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the ﬂ oor.

Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge connection, must be installed immediately upstream of your dryer’s gas supply connection.

Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the system.

DO NOT reuse old ﬂ exible metal gas lines. Flexible gas lines must be design certiﬁ ed by the American Gas Association (CGA in Canada).

• Any pipe joint compound used must be resistant to the action of any liqueﬁ ed petroleum gas.

• As a courtesy, most local gas utilities will inspect a gas appliance installation.

GAS IGNITION - Your dryer uses an automatic ignition system to ignite the burner.

There is no constant burning pilot.

COMMONWEALTH OF MASSACHUSETTS INSTALLATION INSTRUCTIONS

01 INSTALLING YOUR DRYER

Your dryer must be installed by a licensed plumber or gas ﬁ tter. A “T” handle manual gas valve must be installed in the gas supply line to your dryer. If a ﬂ exible gas connector is used to install your dryer, the connector may not be longer than 3’ (36”).

• Gas leaks may occur in your system, creating a dangerous situation.

• Gas leaks may not be detected by smell alone.

WARNING

• Gas suppliers recommend that you purchase and install a UL-approved gas detector.

• Install and use it in accordance with the manufacturer’s instructions.

Installing your dryer _17

DV457E(G)-02836E-03_EN.indd 17DV457E(G)-02836E-03_EN.indd 17 2012-12-04  6:44:392012-12-04  6:44:39

Installing your dryer

ELECTRICAL REQUIREMENTS

The wiring diagram is located on the plate below the control panel.

• The improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualiﬁ ed electrician or serviceman if you are in doubt as to whether your dryer

WARNING

is properly grounded. Do not modify the plug provided with your dryer - if it doesn’t ﬁ t the outlet, have a proper outlet installed by a qualiﬁ ed electrician.

• To prevent unnecessary risk of ﬁ re, electrical shock, or personal injury, all wiring and grounding must be done in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 - Latest Revisions and local codes and ordinances. It is your responsibility to provide adequate electrical services for your dryer.

• All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 - Latest Revision (for the U.S.) or CAN/CGA - B149 Installation Codes - Latest Revision (for Canada) and local codes and ordinances.

GROUNDING

This dryer must be grounded. In the event of a malfunction or breakdown, the grounding the product will reduce the risk of electrical shock by providing a path of least resistance for the electrical current.

Gas models

WARNING

Your dryer has a cord with an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances. Do not modify the plug provided with your dryer – if it doesn’t ﬁ t the outlet, have a proper outlet

installed by a qualiﬁ ed electrician. Never connect the ground wire to the plastic plumbing lines, gas lines, or hot water pipes.

Electric models

WARNING

Your dryer has an optional cord with an equipment-grounding conductor and a grounding plug. The cord is sold separately.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer – if it doesn’t ﬁ t the outlet, have a proper outlet installed by a qualiﬁ ed electrician.

If a power cord is not used and the electric dryer is to be permanently wired, the dryer must be connected to a permanently grounded metal wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the dryer.

18_ Installing your dryer

DV457E(G)-02836E-03_EN.indd 18DV457E(G)-02836E-03_EN.indd 18 2012-12-04  6:44:402012-12-04  6:44:40

ELECTRICAL CONNECTIONS

Before operating or testing, follow all grounding instructions in the “Grounding” section on page 18. An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN

EXTENSION CORD.

Gas models – U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is required.

Electric models – U.S. only

Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. Some require 120/208 volt, 60 Hz approved electrical service. The electric service requirements can be found on the data label located behind the door. A 30-ampere fuse or circuit breaker on both sides of the line is required.

• If a power cord is used, the cord should be plugged into a 30-ampere receptacle.

• The power cord is NOT provided with U.S. electric model dryers.

RISK OF ELECTRIC SHOCK:

WARNING

When local codes allow, the electrical supply of the dryer may be connected by means of a new power supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of120/240 volts, 30-ampere with three No. 10 copper wire conductors terminated with closed loop terminals, open-end spade lugs with turned up ends, or with tinned leads.

• Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring must be retained at the dryer cabinet with a suitable UL-listed strain relief.

• Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor. (Use a 4-prong plug for 4 wire receptacles, NEMA type 14-30R.)

Electric models – Canada Only

• A 120/240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or circuit breaker on both sides of the line is required.

• All Canadian models are shipped with the power cord attached. The power cord should be plugged into a 30-ampere receptacle.

In Canada, you may not convert a dryer to 208 volts.

01 INSTALLING YOUR DRYER

Installing your dryer _19

DV457E(G)-02836E-03_EN.indd 19DV457E(G)-02836E-03_EN.indd 19 2012-12-04  6:44:402012-12-04  6:44:40

Installing your dryer

CONNECTING THE INLET HOSE

Method 1

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.

1. If space permits, attach the brass female end of the “Y”

connector to the cold water faucet.

2. Turn the cold water faucet o .

3. Attach the straight end of long hose to the “Y’ connector.

4. Using pliers, tighten the coupling with an additional two-

thirds turn.

Do not overtighten, as this may damage the coupling.

5. Attach the angled end of long hoses to ﬁ ll the valve at the

bottom of the dryer’s rear frame. Screw on the coupling by hand until it is seated on the ﬁ ll valve connector.

6. Using the pliers, tighten the coupling with an additional two-

thirds turn.

Do not overtighten, as this may damage the coupling.

7. Check that the water faucets are on.

8. Check for leaks around the “Y” connector, faucets and

hoses.

Water Hose

Duct Exhaust

Y-Connector

Frame (back)

Water Hose

20_ Installing your dryer

DV457E(G)-02836E-03_EN.indd 20DV457E(G)-02836E-03_EN.indd 20 2012-12-04  6:44:402012-12-04  6:44:40

Method 2

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.

1. If the “Y” connector cannot be attached directly to the cold water faucet, the short hose must be used.

2. Turn the cold water faucet o .

3. Attach the short inlet hose to the cold water faucet.

Screw on the coupling by hand until it is seated on the faucet.

4. Using the pliers, tighten the coupling with an additional twothirds turn.

Do not overtighten, as this may damage the coupling.

5. Attach the ‘Y” connector to the brass male end of the small hose. Screw on the coupling by hand until it is seated on the connector.

6. Using the pliers, tighten the coupling with an additional twothirds turn.

Do not overtighten, as this may damage the coupling.

7. Attach the angled end of long hoses to the ﬁ ll valve at the bottom of the dryer rear frame. Screw on the coupling by hand until it is seated on the ﬁ ll valve connector.

8. Using pliers, tighten the coupling with an additional twothirds turn.

Do not overtighten, as this may damage the coupling.

9. Check that the water faucets are on.

10. Check for leaks around the “Y” connector, faucets and

hoses.

Long hose

Duct Exhaust

Short hose (Inlet to cold water)

“Y” connector

Frame (back)

Water Hose

01 INSTALLING YOUR DRYER

Installing your dryer _21

DV457E(G)-02836E-03_EN.indd 21DV457E(G)-02836E-03_EN.indd 21 2012-12-04  6:44:402012-12-04  6:44:40

Installing your dryer

REPLACEMENT PARTS AND ACCESSORIES

If your dryer requires replacement parts or accessories, contact the dealer where you purchased your dryer or the SAMSUNG customer care center at 1-800-SAMSUNG (726-7864).

INSTALLATION

For the proper installation, we recommend that you hire a qualiﬁ ed installer.

To install

1. Move your dryer to an appropriate location for the

installation. Consider installing the dryer and washer sideby-side, to allow access to the gas, electrical, and exhaust connections. Place two of the carton cushion-tops on the ﬂ oor. Tip your dryer on its side so it lies across both cushiontops.

2. Set your dryer back in an upright position.

3. To ensure that the dryer provides the optimal drying

performance, it must be level. To minimize vibrations, noise, and unwanted movement, the ﬂ oor must be a perfectly level, solid surface.

To set the dryer to the same height as the washer, fully retract the leveling feet by turning them counterclockwise, then loosen the legs by turning them clockwise.

Retract fully Then loosen

Adjust the leveling feet only as much as necessary to level the dryer. Extending the leveling feet more than necessary can cause the dryer to vibrate.

4. Review the “Exhausting” section on page 16 before installing the exhaust system. Install the

ductwork from your dryer to the exhaust hood. The crimped end of the duct sections must point away from your dryer.

DO NOT use sheet metal screws when assembling the ducting. These joints should be taped.

Never use plastic ﬂ exible exhaust material. Tip for tight installations: install a section of the exhaust system onto your dryer before putting

it in place. Use duct tape to secure this section to your dryer, but do not cover the ventilation slots at

the back of the unit in dryer cabinet.

Leveling feet

Level

22_ Installing your dryer

DV457E(G)-02836E-03_EN.indd 22DV457E(G)-02836E-03_EN.indd 22 2012-12-04  6:44:402012-12-04  6:44:40

5. Review the “Electrical requirements” section on page 18. BEFORE OPERATING OR TESTING, follow the grounding instructions in the “Grounding” section on page 18.

U.S. MODELS: RISK OF ELECTRIC SHOCK - All U.S. models are produced for a 3-WIRE SYSTEM

WARNING

CONNECTION. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If the 4-wire system is used, the dryer frame cannot be grounded to the neutral conductor at the terminal block. Refer to the following instructions for 3 and 4-WIRE SYSTEM CONNECTIONS.

Remove the terminal block cover plate. Insert the power cord with a UL-listed strain relief through the hole provided in the cabinet near the terminal block.

A strain relief must be used.

Do not loosen the nuts already installed on the terminal block. Be sure they are tight. Use a 3/8” (1 cm) deep well socket.

6. Review the “Gas requirements” section on page 17. Remove the pipe thread protective cap. Apply a pipe joint compound or about 1 1/2 wraps of Teﬂ on tape over all threaded connections.

The pipe joint compound must be resistant to the actions of any liqueﬁ ed petroleum gas.

Connect the gas supply to your dryer. An additional ﬁ tting is required to connect the 3/4” (1.9 cm) female thread end of a ﬂ exible connector to the 3/8” (1 cm) male threaded end on the dryer.

Securely tighten the gas line ﬁ tting over the threads. Turn on the gas supply. Check all gas connections for leaks using a soap solution. If bubbles appear, tighten the connections and recheck. DO NOT use an open ﬂ ame to

check for gas leaks.

01 INSTALLING YOUR DRYER

Installing your dryer _23

DV457E(G)-02836E-03_EN.indd 23DV457E(G)-02836E-03_EN.indd 23 2012-12-04  6:44:402012-12-04  6:44:40

Installing your dryer

3-WIRE system connections

1. Loosen or remove the center terminal block screw.

2. Connect the neutral wire (white or center wire) of the power cord to the center, silver-colored

terminal screw of the terminal block. Tighten the screw.

3. Connect the other wires to the outer terminal block screws. Tighten the screws.

4. Tighten the strain relief screws.

5. Insert the tab of the terminal block cover into your dryer’s rear panel slot.

6. Secure the cover with a hold-down screw.

1 External ground connector 2 Neutral grounding wire (green/yellow) 3 Center silver-colored terminal block screw 4 Neutral wire (white or center wire) 5 3/4” (1.9 cm) UL-listed strain relief

If converting from a 4-wire electrical system to a 3-wire, the ground strap must be reconnected to the terminal block support to ground the dryer frame to the neutral

WARNING

conductor.

4-WIRE system connections

1. Remove the center terminal block screw.

2. Connect the ground wire (green or unwrapped) of the power cord to the external ground

conductor screw.

3. Connect the neutral wire (white or center wire) of the power cord and the appliance ground

wire (green with yellow stripes) under the central screw of the terminal block.

4. Connect the other wires to the outer terminal block screws. Tighten the screws.

5. Tighten the strain relief screws.

6. Insert the tab of the terminal block cover into your dryer’s rear panel slot.

7. Secure the cover with a hold-down screw.

1 External ground connector 2 Green or bare copper wire of the power cord

/4 in. (1.9 cm) UL-listed strain relief

3 4 Center silver-colored terminal block screw 5 Grounding wire (green/yellow)

6 Neutral wire (white or center wire)

8. With a level, check your dryer and make the necessary adjustments to the leveling legs.

9. At this time, make sure all gas connections (on gas models), exhaust and electrical

connections are complete. Plug in your dryer, and check its operation by using the checklist below.

10. (GAS MODELS ONLY)

The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer o and wait 5 minutes. Be sure the gas supply to your dryer has been turned on. In order to conﬁ rm the gas ignition, check the exhaust for heat.

24_ Installing your dryer

DV457E(G)-02836E-03_EN.indd 24DV457E(G)-02836E-03_EN.indd 24 2012-12-04  6:44:402012-12-04  6:44:40

FINAL INSTALLATION CHECKLIST

• the dryer is plugged into an electrical outlet and is properly grounded.

• The exhaust ductwork is hooked up and the joints are taped.

• A plastic ﬂ exible duct is NOT used.

• Use rigid or sti -walled ﬂ exible metal vent material.

• The dryer is level and is sitting ﬁ rmly on the ﬂ oor.

• Gas models – the gas is turned on with no gas leaks.

• Start your dryer to conﬁ rm that it runs, heats, and shuts o .

DRYER EXHAUST TIPS

A plastic or non-metal ﬂ exible duct presents a potential ﬁ re hazard.

WARNING

1. Make sure your dryer is installed properly so it exhausts air

easily.

Dryer

Wall

Duct Exhaust

01 INSTALLING YOUR DRYER

2. Use a 4” diameter rigid metal duct. Tape all joints, including at the dryer. Never use lint-trapping screws.

3. Keep ducts as straight as possible.

4. Clean all old ducts before installing your new dryer. Be sure

the vent ﬂ ap opens and closes freely. Inspect and clean the exhaust system annually.

Don’t let a poor exhaust system slow the drying process by:

• Restricting your dryer with a poor exhaust system.

• Unnecessarily using long ducts that have many elbows.

• Using a plastic, thin foil, or non-metal ﬂ exible duct.

• Allowing dented or clogged ducts and vent.

Duct

4”

Tape

Installing your dryer _25

DV457E(G)-02836E-03_EN.indd 25DV457E(G)-02836E-03_EN.indd 25 2012-12-04  6:44:402012-12-04  6:44:40

Installing your dryer

DOOR REVERSAL

1. Unplug the power cord.

2. Remove two door hinge screws.

3. Lift the door and remove it.

4. Remove two screws from the frame front.

5. Remove the two screws from the opposite side of the door

hinge.

6. Remove the two screws from the holder lever.

7. Reassemble the two screws on the inside holes.

8. Remove a screw from the door hinge.

The screw is for pre-ﬁ xing the door to the frame front.

26_ Installing your dryer

DV457E(G)-02836E-03_EN.indd 26DV457E(G)-02836E-03_EN.indd 26 2012-12-04  6:44:412012-12-04  6:44:41

9. Reassemble the screw in the other hole.

10. Place the door on the other side and reattach it to the dryer.

11. Reattach the holder lever.

12. Reattach the screws in the remaining holes.

01 INSTALLING YOUR DRYER

Installing your dryer _27

DV457E(G)-02836E-03_EN.indd 27DV457E(G)-02836E-03_EN.indd 27 2012-12-04  6:44:412012-12-04  6:44:41

Installing your dryer

SETTING UP YOUR DRYER FOR THE FIRST TIME

When you turn on your dryer for the ﬁ rst time, the intro animation, which shows the Samsung logo and plays each time you turn on the dryer, appears on the LCD panel. After the animation plays, you are guided through the initial setup procedure. The setup procedure lets you set your dryer preferences and consists of the following 5 steps:

1. Choosing your language

2. Setting the current date

3. Setting the current time

Precautions for using the LCD panel

• If you touch the LCD panel while wearing rubber gloves, it may not operate properly.

• If you touch the LCD panel with wet hands, it may not operate properly or may malfunction.

• If the LCD panel is wet, it may malfunction.

Choosing your language

1. Tap the language you want to use for the

controls, instructions and descriptions shown in the LCD panel. There are 4 available languages: English, Español (Spanish), Français (French) and Portuguese.

2. Tap the Next button when done.

Setting the current date

1. Tap the up and down arrows to set the date.

Tap the left and right arrows at the bottom of the screen to move to other calendar months.

2. Tap the Next button when done.

Setting your current time

1. Set the desired time by tapping on the up and

down arrows.

2. Tap the Next button when done.

28_ Installing your dryer

DV457E(G)-02836E-03_EN.indd 28DV457E(G)-02836E-03_EN.indd 28 2012-12-04  6:44:412012-12-04  6:44:41

Setting the Automatic Update

1. The Automatic Update function allows various

updates such as performance improvements, patches and bug ﬁ xes to be installed automatically by communicating with the update server.

2. When you agree to this setting, you are

considered as having agreed to the terms and conditions for the Automatic Update function.

3. When the software is updated, some functions

provided by the previous software version may be unavailable depending on the update.

After completing the initial setup, you can access each step and change your preferences any time using the Settings control located at the bottom right of the Cycle Selection screen displayed in the LCD panel.

For example, If you want to set the time again...

1. Tap the Settings at the bottom right of the Cycle Selection screen.

2. Tap the Time & Language at the Setting screen.

3. Tap the Change button under the Time.

4. Tap the up and down arrows to change to the desired time.

5. Tap the OK button. You can view and change the settings of the Language and Date through the same steps above.

01 INSTALLING YOUR DRYER

Installing your dryer _29

DV457E(G)-02836E-03_EN.indd 29DV457E(G)-02836E-03_EN.indd 29 2012-12-04  6:44:422012-12-04  6:44:42

Drying a load of laundry

With your new Samsung Dryer, the hardest part of doing laundry will be deciding which load to dry ﬁ rst.

To reduce the risk of ﬁ re, electric shock, or injury to persons,read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

WARNING

DRYING FOR THE FIRST TIME

Before drying laundry for the ﬁ rst time, you must run a complete empty cycle (i.e. no laundry).

1. Press the Power button.

2. Press the Start/Pause button.

The dryer runs the Normal cycle. This is the factory default cycle the washer will run until you select another cycle. This ﬁ rst empty cycle removes any water that might be left over in the machine from the manufacturer’s test run.

BASIC INSTRUCTIONS

1. Load your laundry into the dryer.

Do not overload the dryer. To determine the load capacity for each type of laundry, refer to the “Cycle chart” section on page

WARNING

65.

Make sure that laundry is not caught in the door.

2. Close the door until it latches.

3. Turn the power on.

4. Select the appropriate cycle and its options in the LCD panel.

5. The selected cycle and its selected options light up and the estimated cycle time appears at the top

right of the LCD panel.

6. Press the Start/Pause button.

Do not touch the door glass while your dryer is running. It may be hot.

30_ Drying a load of laundry

DV457E(G)-02836E-03_EN.indd Sec3:30DV457E(G)-02836E-03_EN.indd Sec3:30 2012-12-04  6:44:422012-12-04  6:44:42

+ 186 hidden pages