Samsung DP15HS-HT, DP17LS-LT User Manual

COLOR MONITOR

DP15HS/HT
DP17LS/LT

Manual

SERVICE

COLOR MONITOR CONTENTS

EXIT

EXIT

MENU

1. Precautions

2. Product Specifications

3. Disassembly & Reassembly

4. Alignment & Adjustments

5. Troubleshooting

6. Exploded View & Parts List

7. Electrical Parts List

8. Block Diagram

9. Wiring Diagram

10. Schematic Diagrams

Copyright

© 1999 by Samsung Electronics Co., Ltd.

All rights reserved.

This manual may not, in whole or in part, be
copied, photocopied, reproduced, translated, or
converted to any electronic or machine readable
form without prior written permission of
Samsung Electronics Co., Ltd.

DP15H*/DP17L* Service Manual
First edition May 1999.

Printed in Korea.

Trademarks

Samsung is a registered trademark and
DP15H*/DP17L* and MacMaster Cable Adapter
are trademarks of Samsung Electronics Co., Ltd.

Macintosh, Centris, Quadra, Duo Dock, and
Power Macintosh are trademarks of Apple
Computer, Inc.

All other trademarks are the property of their
respective owners.

ii DP15H*/DP17L*

WARNINGS

1. For continued safety, do not attempt to modify the
circuit board.

2. Disconnect the AC power before servicing.

3. When the chassis is operating, semiconductor
heatsinks are potential shock hazards.

1-1-1 Servicing the High Voltage VR

and CRT :

WARNING: A high voltage VR replaced in the wrong

direction may cause excessive X-ray
emissions.

Caution:

When replacing the high voltage
adjustment VR, it must be fixed by a
soldering iron after it is properly set.

1. When servicing the high voltage system, remove
the static charge by connecting a 10 kohm resistor
in series with an insulated wire (such as a test
probe) between the chassis and the anode lead.

2. If the HV VR requires adjustment, (a) Replace the
VR and adjust the high voltage to the specification.
(b) Use a soldering iron to melt the adjustment cap
on the HV VR to prevent any movement.

3. When troubleshooting a monitor with excessively
HV, avoid being unnecessarily close to the monitor.
Do not operate the monitor for longer than is
necessary to locate the cause of excessive voltage.

4. High voltage should always be kept at the rated
value, no higher. Only when high voltage is
excessive are X-rays capable of penetrating the shell
of the CRT, including the lead in glass material.
Operation at high voltages may also cause failure of
the CRT or high voltage circuitry.

5. When the HV regulator is operating properly, there
is no possibility of an X-ray problem. Make sure the
HV does not exceed its specified value and that it is
regulating correctly.

6. The CRT is especially designed to prohibit
X-ray emissions. To ensure continued X-ray
protection, replace the CRT only with one that is
the same or equivalent type as the original.

7. Handle the CRT only when wearing shatterproof
goggles and after completely discharging the high
voltage anode.

8. Do not lift the CRT by the neck.

1-1-2 Fire and Shock Hazard :

Before returning the monitor to the user, perform the
following safety checks:

1. Inspect each lead dress to make certain that the
leads are not pinched or that hardware is not
lodged between the chassis and other metal parts in
the monitor.

2. Inspect all protective devices such as nonmetallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators, etc.

3. Leakage Current Hot Check (Figure 1-1):

WARNING: Do not use an isolation transformer during

this test.

Use a leakage current tester or a metering system
that complies with American National Standards
Institute (

ANSI C101.1, Leakage Current for

Appliances), and Underwriters Laboratories (UL
Publication UL1410, 59.7).

4. With the unit completely reassembled, plug the AC
line cord directly into a 120V AC outlet. With the
unitÕs AC switch first in the ON position and then
OFF, measure the current between a known earth
ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including: metal cabinets,
screwheads and control shafts. The current
measured should not exceed 0.5 milliamp. Reverse
the power-plug prongs in the AC outlet and repeat
the test.

Figure 1-1. Leakage Current Test Circuit

1-1-4 Product Safety Notices

Some electrical and mechanical parts have special
safety-related characteristics which are often not
evident from visual inspection. The protection they give
may not be obtained by replacing them with
components rated for higher voltage, wattage, etc. Parts
that have special safety characteristics are identified by

on schematics and parts lists. A substitute
replacement that does not have the same safety
characteristics as the recommended replacement part
might create shock, fire and / or other hazards. Product
safety is under review continuously and new
instructions are issued whenever appropriate.

Components identified by on schematics and parts
lists must be sealed by a soldering iron after
replacement and adjustment.

DP15H*/DP17L* 1-1

1 Precautions

1-1 Safety Precautions

!

DEVICE
UNDER
TEST

TEST ALL

EXPOSED METAL

SURFACES

(READING SHOULD

NOT BE ABOVE 0.5mA)

LEAKAGE
CURRENT

TESTER

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)

EARTH

GROUND

1. Servicing precautions are printed on the cabinet,
and should be followed closely.

2. Always unplug the unitÕs AC power cord from the
AC power source before attempting to: (a) remove
or reinstall any component or assembly, (b)
disconnect PCB plugs or connectors, (c) connect all
test components in parallel with an electrolytic
capacitor.

3. Some components are raised above the printed
circuit board for safety. An insulation tube or tape
is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.

4. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the area around the
serviced part has not been damaged.

1. Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known earth
ground. Alternatively, wear a discharging wrist­strap device. To avoid a shock hazard, be sure to
remove the wrist strap before applying power to
the monitor.

2. After removing an ESD-equipped assembly, place it
on a conductive surface such as aluminum foil to
prevent accumulation of an electrostatic charge.

3. Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage
ESDs.

4. Use only a grounded-tip soldering iron to solder or
desolder ESDs.

5. Use only an anti-static solder removal device. Some
solder removal devices not classified as Òanti-staticÓ
can generate electrical charges sufficient to damage
ESDs.

5. Check the insulation between the blades of the AC
plug and accessible conductive parts (examples:
metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the power
switch ON. Connect an insulation resistance meter
(500 V) to the blades of the AC plug.

The insulation resistance between each blade of the
AC plug and accessible conductive parts (see
above) should be greater than 1 megohm.

7. Never defeat any of the +B voltage interlocks. Do
not apply AC power to the unit (or any of its
assemblies) unless all solid-state heat sinks are
correctly installed.

8. Always connect a test instrumentÕs ground lead to
the instrument chassis ground before connecting the
positive lead; always remove the instrumentÕs
ground lead last.

6. Do not remove a replacement ESD from its
protective package until you are ready to install it.
Most replacement ESDs are packaged with leads
that are electrically shorted together by conductive
foam, aluminum foil or other conductive materials.

7. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.

Caution: Be sure no power is applied to the

chassis or circuit and observe all
other safety precautions.

8. Minimize body motions when handling
unpackaged replacement ESDs. Motions such as
brushing clothes together, or lifting your foot from
a carpeted floor can generate enough static
electricity to damage an ESD.

9. Indicates ESDs on the Schematic Diagram in
this manual.

1 Precautions

1-2 DP15H*/DP17L*

1-3 Electrostatically Sensitive Devices (ESD) Precautions

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly
called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field­effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.

1-2 Servicing Precautions

WARNING1: First read the “Safety Precautions” section of this manual. If unforeseen circumstances

create conflict between the servicing precautions and safety precautions, always
follow the safety precautions.

WARNING2: A high voltage VR replaced in the wrong direction may cause excessive X-ray

emissions.

WARNING3: An electrolytic capacitor installed with the wrong polarity might explode.

DP15H*/DP17L* 2-1

2 Product Specifications

2-1 Specifications

Picture Tube: 15-Inch (38 cm): 13.8-inch (35 cm) viewable, 17-Inch (43 cm): 16-inch (40.6 cm) viewable,

Full-square flat-face tube, 90˚ Deflection, Semi- tint, Non-glare, Invar shadow mask,
Anti-static silica coating, 0.28 mm Dot pitch

Scanning Frequency Horizontal : 30 kHz to 70 kHz (Automatic)

Vertical : 50 Hz to 160 Hz (Automatic)
Display Colors Unlimited colors
Maximum Resolution Horizontal : 1280 Dots Vertical : 1024 Lines
Input Video Signal Analog, 0.7 Vp-p positive at 75 Ω, internally terminated
Input Sync Signal Separate Sync: TTL level positive/negative
Maximum Pixel Clock rate 110 MHz

Active Display 15” ; Horizontal : 267 mm ± 4 mm, Vertical : 200.5 mm ± 4 mm

17” ; Horizontal : 306 mm ± 4 mm (4:3 ratio), Vertical : 230.5 mm ± 4 mm
Input Voltage AC 90 to 264 Volts, 60 Hz or 50 Hz ± 3 Hz
Power Consumption 80 Watt (max) : 15”, 90 Watt (max) : 17”
Dimensions Unit ; 15” : 14.25 x 15.11 x 15.11 Inches (362 x 384 x 384 mm)

(W x D x H) 17” : 16.22 x 16.54 x 16.36 Inches (412 x 420 x 415.5 mm)

Carton ; 15” : 17.87 x 19.57 x 17.52 Inches (454 x 497 x 445 mm)

17” : 21.02 x 21.73 x 18.39 Inches (534 x 552 x 467 mm)

Weight 15” : 26.5 lbs (12.0 kg) / 31.5 lbs (14.3 kg)
(Net/Gross) 17” : 33.1 lbs (15.0 kg) / 38.6 lbs (17.5 kg)

Environmental Considerations Operating Temperature : 32°F to 104°F (0°C to 40°C)

Humidity : 10 % to 80 %

Storage Temperature : -4°F to 113°F (-20°C to 45°C)

Humidity : 5 % to 95 %

• Above models comply with SWEDAC (MPR II) recommendations for reduced electromagnetic fields.

• Designs and specifications are subject to change without prior notice.

Item Description

2 Product Specifications

2-2 DP15H*/DP17L*

2-2 Pin Assignments

5

15

Figure 2-1. Male Type Figure 2-2. Male Type

Sync
Type

Pin No.

Macintosh

Separate

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15

Red
Green
Blue
N-C
DDC Return
GND-R
GND-G
GND-B
N-C
GND-Sync/Self-raster
N-C
DDC Data
H-Sync
V-Sync
DDC Clock

GND-R
Red
H/V Sync
Sense 0
Green
GND-G
Sense 1
Reserved
Blue
Sense 2
GND
V-Sync
GND-B
GND
H-Sync

2 Product Specifications

DP15H*/DP17L* 2-3

QRS

P

O

Video

Sync

Sync

Horizontal

Vertical

CDE

P

O

B

A

Video

Sync

Sync

Separate Sync

2-3 Timing Chart

This section of the service manual describes the timing that the computer industry recognizes as standard
for computer-generated video signals.

C D

A

O

E

B

P

Video

Sync

Sync

Video

Q R S

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
C : Back porch D : Active time Q : Back porch R : Active time
E : Front porch S : Front porch

fH (kHz)
A µsec
B µsec
C µsec
D µsec
E µsec
fV (Hz)
O msec
P msec
Q msec
R msec
S msec
Clock

Frequency
(MHz)

Polarity
H.Sync

V.Sync
Remark

IBM VESA

800/85 Hz
800 x 600

1024/75 Hz
1024 x 768

1024/85 Hz
1024 x 768

VGA3/60 Hz

640 x 480

VGA2/70 Hz

720 x 400

31.469

31.777

3.813

1.907

25.422

0.636

70.087

14.268

0.064

1.080

12.711

0.413

28.322

Negative

Positive

Separate

31.469

31.778

3.813

1.907

25.422

0.636

59.940

16.683

0.064

1.048

15.253

0.318

25.175

Negative
Negative
Separate

37.500

26.667

2.032

3.810

20.317

0.508

75.000

13.333

0.080

0.427

12.800

0.027

31.500

Negative
Negative
Separate

43.269

23.111

1.556

2.222

17.778

1.556

85.008

11.764

0.671

0.578

11.093

0.023

49.500

Negative
Negative
Separate

46.875

21.333

1.616

3.232

16.162

0.323

75.000

13.333

0.064

0.448

12.800

0.021

36.000

Positive
Positive

Separate

53.674

18.631

1.138

2.702

14.222

0.569

85.061

11.756

0.056

0.503

11.179

0.019

56.250

Positive
Positive

Separate

60.023

16.660

1.219

2.235

13.003

0.203

75.029

13.328

0.050

0.466

12.795

0.017

78.750

Positive
Positive

Separate

68.677

14.561

1.016

2.201

10.836

0.508

84.997

11.765

0.044

0.524

11.183

0.015

94.500

Positive
Positive

Separate

800/75 Hz
800 x 600

640/75 Hz
640 x 480

640/85 Hz
640 x 480

Table 2-1. Timing Chart

Mode

Timing

2 Product Specifications

2-4 DP15H*/DP17L*

Memo

4-1-1 Before Making Adjustments

4-1-1 (a) ORIENTATION

When servicing, always face the monitor to the
east.

4-1-1 (b) MAGNETIC FIELDS

Whenever possible, use magnetic field isolation
equipment such as a Helmholtz field to surround
the monitor. If a Helmholtz field is not available,
frequently degauss the unit under test.

Caution: Other electrical equipment may cause

external magnetic fields which may
interfere with monitor performance.

Use an external degaussing coil to limit magnetic
build up on the monitor. If an external degaussing
coil is not available, use the internal degaussing
circuit. However, do not use the internal
degaussing circuit more than once per 30 minutes.

4-1-1 (c) WARM-UP TIME

The monitor must be on for 30 minutes before
starting alignment. Warm-up time is especially
critical in color temperature and white balance
adjustments.

4-1-1 (d) SIGNAL

Analog, 0.7 Vp-p positive at 75 ohm, internal
termination
Sync: Separate
(TTL level negative/positive)

4-1-1 (e) SCANNING FREQUENCY

Horizontal: 30 kHz to 70 kHz (Automatic)
Vertical: 50 Hz to 160 Hz (Automatic)

Unless otherwise specified, adjust at the
17Ó: 1024 x 768 mode (68 kHz/85 Hz),
15Ó: 800 x 600 mode (54 kHz/85 Hz) signals.

Refer to Table 2-1 on page 2-3.

.4-1-2 Required Equipment

The following equipment may be necessary for
adjustment procedures:

4-1-2 (a) DISPLAY CONTROL ADJUSTMENT

1. Non-metallic (Ð) screwdriver:

1.5, 2.5, 3 mm

2. Non-metallic (+) screwdriver:

1.5, 2.5, 3 mm

3. Digital Multimeter (DMM), or
Digital Voltmeter

4. Signal generator, or
DM200 software

5. Software: Softjig or DM200

6. Interface Board Ver. 2.0 Code No.
BH81-90001K

7. Parallel communications cable (25-pin to
25-pin); Code No. BH81-90001H

8. Signal cable (15-pin to 15-pin cable with
additional 3-pin connector); Code No.
BH81-90001J

9. 5 V DC adapter, not supplied

10. Personal computer

Note: Softjig AssÕy (includes items 6, 7 and 9)

Code No. BH81-90001L

4-1-2 (b) COLOR ADJUSTMENTS

1. All equipment listed in 4-1-2 (a), above

2. Color analyzer, or any luminance
measurement equipment

DP15H*/DP17L* 4-1

4 Alignment and Adjustments

This section of the service manual explains how to make permanent adjustments to the monitor. Directions
are given for adjustments using the monitor Interface Board Ver. 2.0 and software (Softjig).

4-1 Adjustment Conditions

Caution: Changes made without the Softjig are saved only to the user mode settings. As such, the

settings are not permanently stored and may be inadvertently deleted by the user.

4-1-3 Connecting the SoftJig

Connect the monitor to the signal generator and/
or PC as illustrated in Figures 4-1 and 4-2.

Note: The signal cable connector which includes

the 3-wire cable must connect to the
monitor. If you use Setup 2 (PC only, no
signal generator) you can only make
adjustments to the signal timing available
on that computer system. To make
corrections to all factory timings requires
the use of an additional signal generator.

4 Alignment and Adjustments

4-2 DP15H*/DP17L*

MONITOR

INTERFACE
BOARD VER. 2.0

PC

SIGNAL
GENERATOR

3-WIRE
CABLE

SIGNAL CABLE

5V DC
ADAPTOR

PARALLEL CABLE

Figure 4-1. Setup 1, With Signal Generator

MONITOR

INTERFACE
BOARD VER. 2.0

PC

3-WIRE CABLE

SIGNAL CABLE

PARALLEL CABLE

D-SUB
CONNECTOR

5V DC
ADAPTOR

Figure 4-2. Setup 2, Without Signal Generator

4-2-1 HIGH VOLTAGE ADJUSTMENT

Signal: 1024 x 768 (68 kHz/85 Hz) (17Ó)

800 x 600 (54 kHz/85 Hz) (15Ó)
Display image: DonÕt care
Contrast: Minimum
Brightness: Minimum
Limit: 26.5 kV ± 0.2 kV (17Ó)

25 kV ± 0.2 kV (15Ó)
exception) 26.0 kV ± 0.2 kV for 17Ó SDD CRT that

the DY type is DMX-1791AT

Measure the hight voltage level at the anode cap.
High voltage should be within the limit as above.
If the high voltage needs adjustment use the
following procedure.

PROCEDURE

1. Turn the power off and disconnect the AC line

cord from the power source.

2. Turn the power on after connecting high

voltage Probe.

3. Using the jig, adjust the high voltage to the

specification.

* High Voltage Adjustment PROCEDURE using Softjig

① Select matching model name in ÒModelÓ field.
➁ Select Ò @7: Zero BeamÓ in menu after

selecting ÒExtra 1Ó

➂ Adjust high voltage using control bar after

selecting ÒHV MINÓ

➃ Turn the power off/on after adjustment

finished.

➄ Check the high voltage has been fixed with

adjusted value after reselecting Ò@7: Zero BeamÓ.

4-2-2 SCREEN VOLTAGE ADJUSTMENT

CONDITIONS

Signal: 1024 x 768 (68 kHz/85 Hz) (17Ó)

800 x 600 (54 kHz/85 Hz) (15Ó)
Display image: DonÕt care
Contrast: Minimum
Brightness: Minimum
Limit: 26.5 kV ± 0.2 kV (17Ó)

25 kV ± 0.2 kV (15Ó)
Screen Voltage adjustment procedure using softjig

is all the same as 4-2-1 but selecting ÒG2 CONTÓ
on the contrary to ÒHV MINÓ.

Table 4-1

4-2-3 CENTER RASTER

Adjust SW401 so that the back raster comes to the
center when you apply each basic mode for 15Ó
and 17Ó.

4-2-4 Centering

Centering means to position the center point of
the display in the middle of the display area.
Horizontal size and position and vertical size and
position control the centering of the display.

Adjust the horizontal size and vertical size to their
optimal settings: 306 mm (H) x 230 mm (V) for
17Ó, 267 mm (H) x 200 mm (V) for 15Ó.

Adjust the horizontal position and vertical
position to ² 4.0 mm of the center point of the
screen.

|A-B| ² 4.0 mm. |C-D| ² 4.0 mm.

Figure 4-3. Centering

* In Softjig window, ÒGeometryÓ has to be

selected for GD adjustment.

4-2-4 (a) HORIZONTAL SIZE ADJUSTMENT
CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)
Display image: Crosshatch pattern
Brightness: Maximum
Contrast: Maximum

4 Alignment and Adjustments

DP15H*/DP17L* 4-3

4-2 Display Control Adjustments

C

A

DISPLAY AREA

EDGE OF BEZEL

B

D

17”

15”

CRT type Screen Voltage

M41QAR361X11*(*)
M41QAQ261X11*(*)
M41LFQ903X28(L), etc

M41EHN325X160/3F**U
M41EHN323X160/3F**U
M41LLJ507XX43*(F5), (F5W3)
M41LLH507XX43*(F5)

M36QAM351X11*(*)
M36LGE128X2**(*)

M36KUK35X02(*/LP), etc

480V

±

10V

500V

±

10V

630V

±

10V

560V

±

10V

600V

±

10V

520V

±

10V

Use control bar after selecting ÒH-SIZEÓ in left
menu to adjust the horizontal size of the display
pattern to 306 mm (17Ó) and 267 mm (15Ó).
(Tolerance: ± 3 mm.)

If ÒH-SIZEÓ is not enough to adjust it, select
ÒSIZE B+Ó by turns.

4-2-4 (b) VERTICAL SIZE ADJUSTMENT
CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)
Display image: Crosshatch pattern
Brightness: Maximum
Contrast: Maximum

Use control bar after selecting ÒV-SIZEÓ in left
menu to adjust the vertical size of the display
pattern to 230 mm (17Ó) and 200 mm (15Ó).
(Tolerance: ± 3 mm.)

4-2-4 (c) HORIZONTAL POSITION ADJUSTMENT
CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

Display image: Crosshatch pattern

Use control bar after selecting ÒH-POSITIONÓ in
left menu to center the horizontal image on the
raster.

4-2-4 (d) VERTICAL POSITION ADJUSTMENT
CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

Display image: Crosshatch pattern

Use control bar after selecting ÒV-POSITIONÓ in
left menu to center the vertical image on the
raster.

4-2-5 Linearity

Linearity affects the symmetry of images as they
appear on the screen. Unless each row or column
of blocks in a crosshatch pattern is of equal size,
or within the tolerances shown in Tables 4-2 and
4-3, an image appears distorted, elongated or
squashed.

Table 4-2. Standard Modes Linearity: 640x480/75Hz,

800x600/85Hz and 1024x768/85Hz

Table 4-3. Other Modes Linearity: VGA, SVGA, XGA,

MAC, etc.

4-2-5 (a) HORIZONTAL LINEARITY ADJUSTMENT
CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)
Display image: Crosshatch pattern
Brightness: Maximum
Contrast: Maximum

To adjust the Horizontal Linearity, refer to Tables
4-2 and 4-3 for the tolerance range.

Increase or decrease H_LIN to optimize the
image.

4-2-5 (b) VERTICAL LINEARITY ADJUSTMENT
CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)
Display image: Crosshatch pattern
Brightness: Maximum
Contrast: Maximum

To adjust the Vertical Linearity, refer to Tables 4-2
and 4-3 for the tolerance range.

Use control bar after selecting ÒV-LINEARITY
BALÓ in left menu to optimize the image.

4 Alignment and Adjustments

4-4 DP15H*/DP17L*

Figure 4-5. Pinbalance

4 : 3

5 : 4

Horizontal: 17.8~20.5
Vertical : 17.8~20.5

Horizontal: 16.7~19.2
Vertical : 17.8~20.5

Supported Timing Mode

Each block (10 %)

Difference between

adjacent blocks (5 %)

Horizontal: Less than 0.96 mm
Vertical : Less than 0.96 mm

Horizontal: Less than 0.90 mm
Vertical : Less than 0.96 mm

4 : 3

5 : 4

Horizontal: 18.2~20.1
Vertical : 18.2~20.1

Horizontal: 17.1~18.9
Vertical : 18.2~20.1

Standard Modes Linearity

Each block (10 %)

Difference between

adjacent blocks (4 %)

Horizontal: Less than 0.77 mm
Vertical : Less than 0.77 mm

Horizontal: Less than 0.72 mm
Vertical : Less than 0.77 mm

4-2-6 Trapezoid Adjustment

CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)
Display image: Crosshatch pattern
Brightness: Maximum
Contrast: Maximum

Use control bar after selecting ÒTRAPEZOIDÓ in
left menu to make the image area rectangular.

Figure 4-4. Trapezoid

4-2-7 Pinbalance Adjustment

CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)
Display image: Crosshatch pattern
Brightness: Maximum
Contrast: Maximum

Figure 4-5. Pinbalance

Use control bar after selecting ÒPINBALANCEÓ in
left menu to optimize the image.

4-2-8 Parallelogram Adjustment

CONDITIONS

Scanning Frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)
Display image: Crosshatch pattern
Brightness: Maximum
Contrast: Maximum

Use control bar after selecting ÒPARALLELÓ in
left menu to make the image area rectangular.

Figure 4-6. Parallelogram

4-2-9 Side Pincushion Adjustment

CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

Display image: Crosshatch pattern

Use control bar after selecting ÒPINCUSHIONÓ in
left menu to straighten the sides of the image area.

4-2-10 Tilt Adjustment

CONDITIONS

Scanning Frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)
Display image: Crosshatch pattern
Brightness: Maximum
Contrast: Maximum

Use control bar after selecting ÒROTATIONÓ in
left menu to correct the tilt of the display.

4-2-11 Degauss

No adjustments are available for the degaussing
circuit. The degaussing circuit can effectively
function only once per 30 minutes.

4-2-12 To Delete the User Mode Data

To delete the adjustment data from the user
modes, click Ò@4: USER DELETEÓ in right ment.

4-2-13 Save the Data

To save the adjustment data for a mode, press
Ò@3: ALL MODE SAVEÓ in right ment.

4 Alignment and Adjustments

DP15H*/DP17L* 4-5

| A - B | < 4 mm

A

4 mm

B

B

A

D1 D2 D1

| C1 |, | C2 | ≤ 2.0 mm, | D1 |, | D2 | ≤ 2.0 mm.

Figure 4-7. Pincushion

C2

C1

D1 D2

CAUTION:Check below condition before color

adjustment
Video signal : Analog 0.7 Vp-p (at 75 Ω)
Sync : TTL level (H, V seperate signal)

* Select ÒColorÓ in Softjig menu for color adjustment.

4-3-1 Color Coordinates (Temperature)

Color temperature is a measurement of the
radiant energy transmitted by a color. For
computer monitors, the color temperature refers
to the radiant energy transmitted by white. Color
coordinates are the X and Y coordinates on the
chromaticity diagram of wavelengths for the
visible spectrum.

CONDITIONS

Measurement instrument: Color analyzer
Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

Display image: White flat field at

center of display area

Luminance: Maximum

PROCEDURE

Use the directions in sections 4-3-2 through 4-3-3
to adjust the color coordinates for:
9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.02
6500K to x = 0.313 ± 0.02, y = 0.329 ± 0.02

4-3-2 Color Adjustments for 9300K

4-3-2 (a) BACK RASTER COLOR ADJUSTMENT
CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)
Display image: Back raster pattern
Brightness: Maximum
Contrast: Maximum

1. Select Ò@1: CHANNEL 1Ó in right menu to

control the color for 9300K.

2. Adjust the luminance of the back raster to

between 0.5 to 0.7 ft-L using contron bar after
selecting ÒGREEN CUTOFFÓ in the menu.

3. Use control bar after selecting ÒBLUE

CUTOFFÓ in left menu to set the ÒyÓ
coordinate to 0.298 ± 0.02.

4. Use control bar after selecting ÒRED

CUTOFFÓ in left menu to 0.283 ± 0.02.

* If color values would not be matched desirable

values, repeat sequence 3 and 4 after readjusting
ÒGREEN CUTOFFÓ control a little different.

4-3-2 (b) WHITE BALANCE ADJUSTMENT
CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)
Display image: White box pattern
Brightness: 0.06ft-L at Back Raster

Pattern Display
Contrast: Maximum

Figure 4-8. White Box Pattern

1. Use control bar after selecting ÒRED GAINÓ,

ÒGREEN GAINÓ and ÒBLUE GAINÓ to adjust
the luminance to 45 ft-L (15Ó) and 46 ft-L
(17Ó) with the color coordinates ranged for
9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.02.

exception) 17Ó SDD CRT type-named
(*/S-2) : 42ft-L.

4-3-2 (c) ABL ADJUSTMENT
CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)
Display image: Full white pattern
Brightness: Maximum
Contrast: Maximum

Figure 4-9. Full White Pattern

1. Check the ABL. If it is not within the

specifications, use the ABL controls to adjust
it. (15Ó: 33 ± 1 ft-L, 17Ó: 36 ± 1 ft-L )

2. Select Ò@4: COLOR SAVEÓ to save the data.

3. Select Ò@6: ALL COLOR SAVEÓ to save the

CH2.

4 Alignment and Adjustments

4-6 DP15H*/DP17L*

4-3 Color Adjustments

1/3H-1/2H

1/3V-1/2V

FRONT BEZEL OPENING
BACK RASTER

WHITE WINDOW

FRONT BEZEL OPENING
BACK RASTER

WHITE WINDOW

4-3-2 (d) WHITE BALANCE ADJUSTMENT VERIFICATION
CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

Display image: Back raster pattern

Full White Pattern

X-Y Coordinates: x = 0.283 ± 0.02,

y = 0.298 ± 0.02
ABL Luminance Refer to 4-3-2(c)
Brightness: Maximum
Contrast: 5 ft-L, 24 ft-L

1. Check whether the color coordinates of the

back raster satisfy the above spec.
If they do not, return to 4-3-2 (a) and readjust

all settings.

2. Display a full white pattern.

3. Select ÒGeometryÓ in softjig menu.

4. Select Ò@7: 5-ft Ò in right menu.

5. Check whether the white coordinates of the

video meet the above coordinates spec.

6. Select Ò@8: 24-ft Ò in right menu.

7. Check whether the white coordinates of the

video satisfies the above spec.
If they do not, return to 4-3-2 (a) and readjust

all settings.

Select ÒColorÓ and click Ò@2: CHANNEL 2Ó
for color ajdustment for 6500K
Repeat the sequence of 9300K adjustment.
The luminance values the same as 9300K, but
the color coordinated of back raster and white
box are : x = 0.313

± 0.02 y = 0.329 ± 0.02

4-3-3 Luminance Uniformity Check

Luminance is considered uniform only if the ratio
of lowest to highest brightness areas on the screen
is not less than 7.5:10.

CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

(1024 x 768)
Display image: White flat field
Brightness: Cut off point at 24 ft-L
Contrast: Maximum

PROCEDURE

Measure luminance at nine points on the display
screen (see figure below).

4-3-4 Focus Adjustment

CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

(1024 x 768)
Display image: ÒHÓ character pattern
Brightness: Cut off point
Contrast: Maximum

PROCEDURE

1. Adjust the Focus VR on the FBT to display the

sharpest image possible.

2. Use Locktite to seal the Focus VR in position.

4-3-5 Color Purity Adjustment

Color purity is the absence of undesired color.
Conspicuous mislanding (unexpected color in a
uniform field) within the display area shall not be
visible at a distance of 50 cm from the CRT
surface.

CONDITIONS

Orientation: Monitor facing east
Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)
Display image: White flat field
Luminance: Cut off point at the center

of the display area

Note: Color purity adjustments should only be

attempted by qualified personnel.

4 Alignment and Adjustments

DP15H*/DP17L* 4-7

Figure 4-10. Luminance Uniformity Check Locations

PROCEDURE

For trained and experienced service technicians
only.

Use the following procedure to correct minor
color purity problems:

1. Make sure the display is not affected by
external magnetic fields.

2. Very carefully break the glue seal between the
2-pole purity convergence magnets (PCM), the
band and the spacer (see Figures 4-12).

3. Make sure the spacing between the PCM
assembly and the CRT stem is 29 mm ± 1 mm.

4. Display a green pattern over the entire display
area.

5. Adjust the purity magnet rings on the PCM
assembly to display a pure green pattern.
(Optimum setting: x = 0.295 ± 0.015,
y = 0.594 ± 0.015)

6. Repeat steps 4 and 5 using a red pattern and
then again, using a blue pattern.

Table 4-4. Color Purity Tolerances

(For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02)

7. When you have the PCMs properly adjusted,
carefully glue them together to prevent their
movement during shipping.

4 Alignment and Adjustments

4-8 DP15H*/DP17L*

Red: x = 0.640 ± 0.015 y = 0.323 ± 0.015
Green: x = 0.295 ± 0.015 y = 0.594 ± 0.015
Blue: x = 0.142 ± 0.015 y = 0.066 ±0.015

DP15H*/DP17L* 5-1

5 Troubleshooting

5-1 Parts Level Troubleshooting

Notes: 1. If a picture does not appear, fully rotate the brightness and contrast controls clockwise and reinspect.

2. Check the following circuits.

• No raster appears: Power circuit, Horizontal output circuit.

• High voltage develops but no raster appears: Video output circuits.

• High voltage does not develop: Horizontal output circuits.

5-1-1 No Power Supply

Chirping noise exists?

Check and replace IC601.

Check and replace D601, FH1

Done.

No

Yes

Repeating start?

Check and replace D606.

No

Yes

IC601 Pin 1 waveform is right?

Check and replace D614, IC601,

Q602, ZD601.

Yes

No

C622 Voltage is 13 V ± 0.5V?

Check and replace IC201, IC301,

IC401, Q402, Q404.

Yes

No

Normal operation

Replace Main board.

Yes

Verify voltages.

Yes

No

WAVEFORMS

1

1

100 V (IC601, #1)

CH1 P-P = 100 V CH1 RMS = 350.2 V

5 Troubleshooting

5-2 DP15H*/DP17L*

5-1-2 DPMS Failure

Make No H/V sync (power off

mode)

Check signal source

H/V sync video level.

LED blinks

Check IC201 Pin 40.

Yes

No

+12 V line off

Check IC201 Pin 5.

Yes

No

IC602 Pin 4

voltage exists?

Check IC201 Pin 6.

Check and replace IC602.

No

Yes

IC601 Pin 1 output

voltage exists?

Refer to 5-1-1 No Power Supply.

Done

Yes

No

WAVEFORMS

2

2

100V (IC601, #1)

CH1 P-P = 100V CH1 RMS = 325.8 V

5 Troubleshooting

DP15H*/DP17L* 5-3

5-1-3 H_Deflection Failure

Does Horizontal paluse signal

appear at at Pin 8 of IC401?

Check IC401.

Yes

No

Does 110 Vp-p signal appear

at Collector of Q403?

Check Q443.

No

No

Check Q402, Q404, T401.

WAVEFORMS

4

3

2.00 V (IC401, #6)

CH1 P-P = 2.00V CH1 RMS = 5.868V

4

1.00V (IC401, #8)

CH1 P-P = 1.00V CH1 RMS = 1.298V

5

20.0 V (Q403, Collector)

CH1 P-P = 20.0 V CH1 RMS = 46.80V

Does PWM output signal appear

at Pin 6 (H_out) of IC401?

Check IC401.

Check 12 V line.

Yes

No

Does DC 12V appear at

Pin 10 of IC401?

Yes

No

3

7-1-4 S Correction Failure

S1~S3 signals are right at each

frequency block?

Check S1 ~ S3 signal.

Check and replace Q404, Q409, Q410,

Q414, Q415, Q416

Yes

Check and replace IC201.

No

5

5 Troubleshooting

5-4 DP15H*/DP17L*

5-1-5 H_Lin. Failure

IC201 Pin 21 voltage varies with

different H_Lin. DAC values?

IC603 Pin 9 voltage varies with

different H_Lin. DAC values?

Check +12 V, –10 V line.

Check some parts around IC603.

Check Q412, Q413, T402.

Yes

Yes

No

Replace IC201.

No

5-1-6 Invariable H_Size

IC401 Pin 6 voltage varies with

different B_Out DAC values?

Q402 Gate output duty varies with

different B_Out DAC values?

Check some parts around Q402,

IC401 Pin 3 ~ 6.

Yes

No

Check and replace IC401.

No

5-1-7 Abnormal H_Size

IC401 Pin 11 output duty

varies with different B+ offset

DAC values?

Q408 Collector waveform is

right?

Check and replace Q405, Q406, Q407,

Q408.

Check some parts around D409, L401.

Yes

Yes

No

Check and replace IC201.

No

WAVEFORMS

6

6

200 V (Q408, Collector)

CH1 P-P = 200V CH1 RMS = 387.2V

5 Troubleshooting

DP15H*/DP17L* 5-5

5-1-8 Side Pin or Trap Failure

IC401 Pin 11 output exists?

Yes

Check and replace IC401.

Refer to 5-1-7

Abnormal H_Size

.

5-1-9 Para. or Pin Balance Failure

IC401 Pin 11 output varies with

different DAC values?

No

Replace IC401.

No

WAVEFORMS

7

7

1.00 V (IC401, #11)

CH1 P-P = 1.00V CH1 RMS = 3.008 V

5-1-10 Tilt Failure

IC201 Pin 20 output duty varies

with different DAC values?

IC603 Pin 13 output varies with

different DAC values?

Check and replace IC603.

Check and replace Q301, Q302.

Yes

Yes

No

Check and replace IC201.

No

Check tilt connector connection

Refer to 5-1-7

Abnormal H_Size

.

Yes

5 Troubleshooting

5-6 DP15H*/DP17L*

5-1-11 V Deflection Failure

13 V, –10 V line is on?

IC401 Pin 12 output exists?

Check and replace IC401.

Yes

Yes

No

Refer to 5-1-1 No Power Supply

No

IC301 Pin 6 output exists?

Check and replace some parts

around IC301.

Yes

No

Check DY connector connection.

WAVEFORMS

8

9

8

500 V (IC401, #12)

CH1 P-P = 500 V CH1 RMS = 1.425 V

9

10.0 V (IC301, #6)

CH1 P-P = 10.0 V CH1 RMS = 5.06 V

5-1-12 V Size or Pos. Variation Failure

IC401 Pin 12 output varies with

different DAC values?

Yes

Check and replace IC201, IC401.

Check and replace IC301.

No

5 Troubleshooting

DP15H*/DP17L* 5-7

5-1-13 High Voltage Failure

IC401 Pin 6 OSC pulse exists?

Q402 Gate driving pulse exists?

Check and replace Q401.

Yes

Yes

No

Check and replace IC401

and +12 V line.

No

Q402 Drain pulse exists?

Check and replace Q403,

L402.

Yes

No

Done

WAVEFORMS

10

3

11

2.00 V (Q402, Gate)

CH1 P-P = 2.00 V CH1 RMS = 7.692V

3

2.00 V (IC401, #6)

CH1 P-P = 2.00 V CH1 RMS = 5.868 V

11

50.0 V (Q402, Drain)

CH1 P-P = 50.0 V CH1 RMS = 73.7V

IC101 Pin 12 input exists and

varies with different patterns?

Check and replace IC101.

Input full white pattern to monitor.

No

Yes

No

T501 Pin 8 output exists?

Check and replace T501.

Yes

No

IC201 Pin 26 output exists and
varies with different patterns?

Check and replace IC201.

Yes

No

Done

Check CN102.

5-1-14 ABL Failure

11

5 Troubleshooting

5-8 DP15H*/DP17L*

5-1-15 Dynamic Focus Failure

IC401 Pin 32 output is right?

Some parts around Q551 are right?

Replace failed part.

Yes

Yes

No

Replace the IC401.

No

T502 Pin 6 input is right?

Check and replace C432.

Yes

No

T502 Pin 1 output is right?

Replace the T502.

No

No

Check the connection between FBT

Focus pin, CRT Socket PCB.

WAVEFORMS

13

14

12

12

2.00 V (IC401, #32)

CH1 P-P = 2.00V CH1 RMS = 6.124V

13

50.0 V (T502, #6)

CH1 P-P = 50.0V CH1 RMS = 75.6V

14

100 V (T502, #1)

CH1 P-P = 100V CH1 RMS = 124.0V

5 Troubleshooting

DP15H*/DP17L* 5-9

5-1-16 No Video

IC101 Pins 5, 8 and 10 inputs

are right?

IC101 Pins 21, 24 and 26

outputs are right?

Check I2C bus and +12 V line.

Yes

Yes

No

Check the signal cable connection.

No

IC103 Pins 1, 2 and 3 outputs

are right?

Check +12 V, +72 V line.

Check and replace IC103.

Yes

No

Cathode DC levels are right?

Check +72 V line.

Check and replace QR01, QR02,

QG01, QG02, QB01, QB02.

Yes

No

G2 voltage is right?

Check G2 wire, CRT Socket board,

and FBT.

Change CRT.

Yes

Done.

No

Check signal cable and connection.

WAVEFORMS

15

16

17

15

1.00 V (IC101, #5, 8, 10)

CH1 P-P = 1.00V CH1 RMS = 2.452V

16

1.00 V (IC101, #21,24,26)

CH1 P-P = 1.00V CH1 RMS = 2.792V

17

20.0 V (IC103, #1, 2, 3)

CH1 P-P = 20.0V CH1 RMS = 40.52V

5 Troubleshooting

5-10 DP15H*/DP17L*

5-1-17 Micom Failure

IC201 Pin 11 input voltage is 5V?

IC201 Pins 13 and 14 inputs

are right?

Check C202, C203, X201.

Yes

Yes

No

Check IC604.

No

IC201 Pin 18 input is right?

Check IC605.

Yes

No

All in/output values are right?

Replace IC201.

No

No

Done

WAVEFORMS

18

18

1.00 V (IC201, #13, 14)

CH1 P-P = 1.00 V CH1 RMS = 2.108V

5 Troubleshooting

DP15H*/DP17L* 5-11

5-1-18 OSD Failure

IC104 Pin 6 input is right?

IC104 Pin 17 input is right?

Check and replace Q101.

Check CN102 Pin 8.

Yes

Yes

No

Check and replace Q102.

Check CN102 Pin 14.

No

IC104 Pins 7 and 8 inputs are

right?

Check IC201 Pins 41 and 42.

Yes

No

IC104 Pins 12, 13 and 14

outputs are right?

Check and replace IC104.

No

No

IC101 Pins 21, 24 and 26

outputs are right?

Check and replace IC101.

Check and replace IC103.

Yes

Done

No

Check CN104 and connector Ass’y.

WAVEFORMS

19

20

21

19

1.00 V (IC104, #6)

CH1 P-P = 1.00V CH1 RMS = 4.516V

20

1.00 V (IC104, #17)

CH1 P-P = 1.00V CH1 RMS = 5.024V

21

1.00 V (IC101, #21.24.26)

CH1 P-P = 1.00V CH1 RMS = 2.580V

5 Troubleshooting

5-12 DP15H*/DP17L*

5-1-19 User Control Failure

Does the DC level change at

Pin 36 of IC201 when you push the

button S/W?

Yes

Check the button.

(SW201 ~ SW204)

No

Check IC201.

RL601 operation is right?

Q601 base input is right?

Check and replace Q601.

No

No

Yes

Check D-coil and TH601.

Yes

IC201 Pin 4 output is right?

Check and replace IC201.

Yes

No

Done

Check degaussing connector.

5-1-20 Degaussing Failure

5 Troubleshooting

DP15H*/DP17L* 5-13

5-2 General Troubleshooting

5-2-1 No Picture

LED blinks?

LED is green color?

Check Micom.

Check G2 voltage, high voltage,

R, G, B cathode voltage.

Yes

No

No

Refer to 5-2-2 Shut down.

Yes

5-2-2 Shut Down

Blinking LED’s?

Scan failure

Check horizontal, vertical deflection

system and check power supply

secondary voltages.

Yes

Yes

Check power supply.

No

Check and replace IC201.

Done

No

Video failure?

Check Video board.

No

Yes

5 Troubleshooting

5-14 DP15H*/DP17L*

5-2-3 Missing Color

Are proper Video levels

on CN101 (D-Sub) Pins 1, 3 and 5?

Are proper Video signal on all

cathodes?

Refer to 5-1-16 No Video.

Yes

Yes

No

Check signal generator.

No

Are proper DC voltage on all

cathodes?

Check IC101 Pins 15, 16 and 17.

Check QR01, QR02, QG01, QG02,

QB01 and QB02.

Yes

Yes

No

Is G2 voltage right?

Check D502, D503, Q501.

No

Is Heater voltage right?

Check D608, Q604, T601.

No

Yes

Check D504, Q602, T501.

No

Yes

Yes

Yes

Is G1 voltage right?

No

Replace CRT.

Done

22

WAVEFORMS

22

10.0 V (R,G,B, Video)

CH1 P-P = 10.0V CH1 RMS = 17.02V

5 Troubleshooting

DP15H*/DP17L* 5-15

Is G2 voltage right?

Is blank pulse on Pin 17 of IC401?

Check IC401.

Yes

Yes

No

Check D502, D503, Q501 and Adjust

G2.

No

Is V_FLB pulse on

Collector of Q303?

Check Q303.

Done

Yes

No

Does approve the Vertical pulse

on the CRT Socket G1?

Check CN102, CN201.

Yes

No

Check white balance adjustment.

5-2-4 Visible Retrace

23

24

WAVEFORMS

23

5.00 V (Q303, Collector)

CH1 P-P = 5.00V CH1 RMS = 28.33V

24

20.00 V (CRT, G1)

CH1 P-P = 20.0V CH1 RMS = 66.68V

5 Troubleshooting

5-16 DP15H*/DP17L*

Are signals right?

Signals at Pins 28 and 29 of

IC201 are right?

Check IC201.

Yes

Yes

No

Check Video Cable

No

Signals at Pins 14 and 15 of

IC401 are right?

Check IC401

Check circuits on Main board.

Yes

Done

No

Check input signals Pins 2

and 3 of CN202.

5-2-5 Unsynchronized Image

5 Troubleshooting

DP15H*/DP17L* 5-17

Is the convergence now

within spec?

Readjust convergence.

No

Done

Yes

Is the convergence now

within spec?

Done

Change CRT and readjust

convergence.

No

Done

Yes

Try readjusting convergence.

5-2-6 Misconvergence

5 Troubleshooting

5-18 DP15H*/DP17L*

Improved focus?

Check focus leads from FBT

to CRT Socket.

Check the CRT Socket.

No

Aging monitor and check for focus

change.

Yes

Is dynamic focus circuit right?

Refer to 5-1-15 Dynamic

Focus Failure.

Replace the CRT and verify focus.

Yes

No

Adjust focus VR of FBT.

5-2-7 Poor Focus

5-2-8 Purity Failure

Purity is right?

Degaussing circuit is right?

Refer to 5-1-20 Degaussing Failure.

Replace CRT and verify purity.

Yes

No

No

Done

Yes

Degaussing

6 Exploded View and Parts List

6-1 DP15HS

DP15H*/DP17L* 6-1

6 Exploded View & Parts List

6-2 DP17LS

6-2 DP15H*/DP17L*

6-1-1 Front Cover & CRT Ass’y (DP15HS)

6 Exploded View & Parts List

DP15H*/DP17L* 6-3

6-1-2 Chassis & Stand Ass’y (DP15HS)

6 Exploded View & Parts List

6-4 DP15H*/DP17L*

6-1-3 Rear Cover Ass’y (DP15HS)

8 Exploded View & Parts List

DP15H*/DP17L* 6-5

6-2-1 Front Cover & CRT Ass’y (DP17LS)

6 Exploded View & Parts List

6-6 DP15H*/DP17L*

6-2-2 Chassis & Stand Ass’y (DP17LS)

6 Exploded View & Parts List

DP15H*/DP17L* 6-7

6-2-3 Rear Cover Ass’y (DP17LS)

6 Exploded View & Parts List

6-8 DP15H*/DP17L*

Loc. No. Code No. Description Specification Remarks

BD301 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500
BD401 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500
BD402 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 17”
BD402 BH39-40305U CBF-HARNESS 52MM,AWG22(0.6PI) 15”
BD601 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500
BD602 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500
BD603 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500
C201 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5
C202 2201-000389 C-CERAMIC,DISC 22pF,5%,50V,CH,TP,5.0*3.0
C203 2201-000389 C-CERAMIC,DISC 22pF,5%,50V,CH,TP,5.0*3.0
C204 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5
C205 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5
C206 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5
C207 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5
C209 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5
C210 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5
C211 2201-000146 C-CERAMIC,DISC 100pF,5%,50V,SL,TP,5x3,5
C212 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,4x3.5,
C213 2401-000029 C-AL 10uF,20%,100V,GP,TP,6.3x11,5
C214 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5
C215 2201-000146 C-CERAMIC,DISC 100pF,5%,50V,SL,TP,5x3,5
C216 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5
C217 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
C220 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5
C301 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm
C302 2305-000291 C-FILM,MPEF 220nF,5%,63V,TP,7.5x13.5mm,5
C305 2401-000037 C-AL 470uF,20%,16V,GP,TP,8x11.5,5
C306 2401-000856 C-AL 220uF,20%,35V,WT,TP,10x20,5
C307 2305-000237 C-FILM,MPEF 1uF,5%,63V,TP,7.5x15.5mm,5mm
C308 2301-000013 C-FILM,PEF 4.7nF,5%,100V,TP,10.5x12.5x6
C309 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V
C311 2301-001027 C-FILM,PEF 15nF,10%,250V,TP,9.5x12x4.5,5
C312 2401-001016 C-AL 3.3UF,20%,50V,BP,TP,5X11,5
C401 2301-000312 C-FILM,PEF 8.2nF,5%,100V,TP,6x12.5mm,5mm
C402 2201-000021 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP
C403 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm
C404 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm
C405 2201-000823 C-CERAMIC,DISC 270pF,5%,50V,SL,TP,5x3,5
C406 2301-000231 C-FILM,PEF 3.3nF,5%,100V,TP,5.8x12.5mm,5
C407 2401-000540 C-AL 150uF,20%,63V,LZ,TP,10x25,5
C408 2201-000469 C-CERAMIC,DISC 330pF,10%,500V,Y5P,TP,6x4
C409 2306-000147 C-FILM,MPPF 1uF,5%,250V,BK,26x24x15,22.5
C410 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5
C411 2301-000005 C-FILM,PEF 33nF,5%,100V,TP,5.8x12.5x3,5
C412 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm

7 Electrical Parts List

DP15H*/DP17L* 7-1

7 Electrical Parts List

7-1 Main PCB Parts

C413 2401-001012 C-AL 3.3UF,20%,50V,BP,TP,16X25,7.5
C414 2401-001334 C-AL 470nF,20%,50V,GP,TP,5x11,2.5
C415 2401-001218 C-AL 4.7uF,20%,100V,WT,TP,5x11,5 17”
C415 2401-000043 C-AL 1uF,20%,160V,GP,TP,6.3x11,5 15”
C416 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm
C417 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm
C419 2309-000106 C-FILM,MPE-PPF 2.2nF,5%,1.6KV,TP,23x16x9
C420 2309-000107 C-FILM,MPE-PPF 2.5nF,5%,1.6KV,BK,23x17x1 17”
C420 2309-000106 C-FILM,MPE-PPF 2.2nF,5%,1.6KV,TP,23x16x9 15”
C421 2303-001029 C-FILM,PPF 5.2nF,5%,630V,TP,19x7x13,7.5
C423 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5
C425 2306-000119 C-FILM,MPPF 100nF,5%,250V,TP,19x14.5x6.5 17”
C425 2306-000131 C-FILM,MPPF 150nF,5%,250V,TP,19x16x7.5,7 15”
C426 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5
C427 2306-000164 C-FILM,MPPF 220nF,5%,250V,TP,19x22x10,7 17”
C427 2306-000179 C-FILM,MPPF 300nF,5%,250V,TP,20x18.5x10 15”
C429 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5
C430 2306-000249 C-FILM,MPPF 680nF,5%,250V,TP,26x20.5x12
C431 2306-000179 C-FILM,MPPF 300nF,5%,250V,TP,20x18.5x10 SDD,TSB
C431 2306-000171 C-FILM,MPPF 270nF,5%,250V,TP,20x18.5x10 PHS
C432 2305-001033 C-FILM,MPEF 15nF,10%,250V,TP,13X9.0X4.5m
C433 2305-001003 C-FILM,MPEF 10nF,5%,250V,TP,13x4.5x9mm,7
C434 2401-001016 C-AL 3.3UF,20%,50V,BP,TP,5X11,5
C435 2201-000469 C-CERAMIC,DISC 330pF,10%,500V,Y5P,TP,6x4
C436 2201-000012 C-CERAMIC,DISC 220pF,10%,1KV,Y5P,TP,6x5 15”
C501 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm
C502 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm
C503 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5
C504 2301-000004 C-FILM,PEF 2.2nF,5%,100V,TP,5.5X10X2.9,5 17”
C504 2301-000004 C-FILM,PEF 2.2nF,5%,100V,TP,5.5X10X2.9,5 15”
C505 2401-000059 C-AL 220nF,20%,50V,GP,5x11,5
C506 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP 17”
C507 2201-000291 C-CERAMIC,DISC 1nF,10%,500V,Y5P,TP,8.5x5
C508 2401-002267 C-AL 2.2uF,20%,250V,GP,TP,8x11.5,5 17”
C509 2401-002267 C-AL 2.2uF,20%,250V,GP,TP,8x11.5,5
C510 2301-000005 C-FILM,PEF 33nF,5%,100V,TP,5.8x12.5x3,5
C511 2301-000231 C-FILM,PEF 3.3nF,5%,100V,TP,5.8x12.5mm,5
C512 2201-000020 C-CERAMIC,DISC 10nF,10%,1KV,Y5P,BK,20x5, 15”
C513 2201-000291 C-CERAMIC,DISC 1nF,10%,500V,Y5P,TP,8.5x5 17”
C514 2401-001334 C-AL 470nF,20%,50V,GP,TP,5x11,2.5
C515 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm
C551 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5 17”
C552 2201-000132 C-CERAMIC,DISC 100pF,10%,500V,Y5P,TP,6x4 17”
C601 2301-001195 C-FILM,MPPF 150nF,10%,275VAC,BK,26x16.5x
C602 2301-001195 C-FILM,MPPF 150nF,10%,275VAC,BK,26x16.5
C603 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11

!!!!!

!

7 Electrical Parts List

7-2 DP15H*/DP17L*

Loc. No. Code No. Description Specification Remarks

Loc. No. Code No. Description Specification Remarks

C604 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11
C607 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
C608 2401-003367 C-AL 180uF,20%,400V,GP,BK,25x35mm,1
C609 2401-000971 C-AL 22uF,20%,50V,WT,TP,6x11mm,5mm
C610 2301-000284 C-FILM,PEF 47nF,5%,100V,TP,8.5x12.5mm,5m
C611 2401-000613 C-AL 1uF,20%,50V,WT,TP,5x11,5
C612 2401-000613 C-AL 1uF,20%,50V,WT,TP,5x11,5
C613 2201-000012 C-CERAMIC,DISC 220pF,10%,1KV,Y5P,TP,6x5
C614 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP
C615 2201-000291 C-CERAMIC,DISC 1nF,10%,500V,Y5P,TP,8.5x5
C616 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x
C617 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x
C618 2401-000039 C-AL 1000uF,20%,16V,GP,TP,10x16,5
C619 2201-000469 C-CERAMIC,DISC 330pF,10%,500V,Y5P,TP,6x4
C620 2401-000540 C-AL 150uF,20%,63V,LZ,TP,10x25,5
C621 2401-001551 C-AL 47uF,20%,35V,GP,TP,6.3x11,5 17”
C621 2401-001551 C-AL 47uF,20%,35V,GP,TP,6.3x11,5 15”
C622 2401-000039 C-AL 1000uF,20%,16V,GP,TP,10x16,5
C623 2401-000039 C-AL 1000uF,20%,16V,GP,TP,10x16,5
C626 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5
C627 2401-000292 C-AL 100uF,20%,16V,WT,TP,8x11.5mm,5
C630 2401-001561 C-AL 47uF,20%,35V,WT,TP,8x11.5,5
C631 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
CIS BH39-00016A CBF-SIGNAL -,1550MM,-,IVORY(IV01),2990
CIS 0402-001257 DIODE-RECTIFIER DTV32F,1500V,15A,TO-220A 15”
CLAMP 6502-000001 CABLECLAMP DAWH-5NB,D15,L35,NTR,NYLON66 17”
CN201 3711-003895 CONNECTOR-HEADER BOX,13P,1R,2mm,STRAIGHT
CN202 3711-003873 CONNECTOR-HEADER BOX,7P,1R,2mm,STRAIGHT
CN301 3711-001483 CONNECTOR-HEADER NOWALL,3P,1R,5.0mm,STRA
CN302 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK
CN303 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK
CN304 3711-000197 CONNECTOR-HEADER 1WALL,3P,1R,2.5mm,STRAI
CN401 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK
CN402 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK
CN501 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK
CN501+G2Y BH39-00014A CBF-HARNESS 1P,280MM,RED,UL1032,AWG22,YF
CN502 3711-001483 CONNECTOR-HEADER NOWALL,3P,1R,5.0mm,STRA 17”
CN502 3711-000024 CONNECTOR-HEADER BOX,3P,1R,2.5mm,STRAIGH 15”
CN601 3721-001027 PLUG-ACPOWER 3P,NI
D301 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP
D401 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP
D402 0402-000006 DIODE-RECTIFIER 1N4007GP,1000V,1A,DO-41
D403 0402-000006 DIODE-RECTIFIER 1N4007GP,1000V,1A,DO-41
D404 0402-000006 DIODE-RECTIFIER 1N4007GP,1000V,1A,DO-41
D405 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP
D406 0402-001025 DIODE-RECTIFIER ERD07-15,1500V,1.5A

!!!!!

7 Electrical Parts List

DP15H*/DP17L* 7-3

D407 0402-001118 DIODE-RECTIFIER UF1G,400V,1.2A,DO-204AL
D408 0402-001255 DIODE-RECTIFIER DTV56F,1500V,10A,TO-220A 17”
D409 0402-001256 DIODE-RECTIFIER SUF30JL,600V,3A,P600,BK
D410 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,T
D411 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,T
D412 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,T
D413 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,T
D420 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D421 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D422 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D501 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D502 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP
D503 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,T 17”
D504 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,T
D505 0401-000004 DIODE-SWITCHING 1SS244,250V,200mA,DO-34
D506 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,T
D507 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D508 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D509 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D510 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D511 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D512 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D513 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D601 0402-000103 DIODE-BRIDGE D2SBA60,600V,1.5A,SIP-4,ST
D602 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D604 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP
D605 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP
D606 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,T
D607 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D608 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP
D609 0402-000005 DIODE-RECTIFIER 31DF4,400V,3A,DO-201AD,B
D610 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP
D611 0402-001118 DIODE-RECTIFIER UF1G,400V,1.2A,DO-204AL,
D612 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,T
D614 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,T
D615 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D616 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
FBT 6502-000001 CABLECLAMP DAWH-5NB,D15,L35,NTR,NYLON66 15”
FH1 3602-000001 FUSE-CLIP 30mohm
FUSE 3601-000004 FUSE-FERRULE 250V,3.15A,SB,CERAMIC,5x20m
GT601 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK
GT602 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK
GT603 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK
GT604 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK
HS301 BH99-00002A ASSY,HEAT/SINK H/SV.IC,SCREW+NUT,KA2142
HS401 BH99-00006A ASSY,HEAT/SINK H/S,SCREW+NUT,IRF630
HS402 BH99-00005A ASSY,HEAT/SINK H/S,SCREW+NUT,IRF630

!

!

7 Electrical Parts List

7-4 DP15H*/DP17L*

Loc. No. Code No. Description Specification Remarks

Loc. No. Code No. Description Specification Remarks

HS501 BH99-00001B ASSY,HEAT/SINK H/SFBT,SPRING,KA5802,DTV5 17”
HS501 BH99-00001A ASSY,HEAT/SINK H/SFBT,SPRING,KA5802,DTV3 15”
HS601 BH99-00003A ASSY,HEAT/SINK H/SPOWER,SPRING,DP104
IC201 BH09-00006A MICOM MASKING DM024, 42P
IC201_SOCK 3704-001071 SOCKET-IC 42P,DIP,SN,1.778mm
IC202 1103-001149 IC-EEPROM 24C041,4KBIT,DIP,8P,300MIL,10M
IC301 1204-001508 IC-VERTICALDEF. KA2142,SIP,10P,-,PLASTIC
IC401 1204-001509 IC-HOR./VER.PROCESSO TDA4859,DIP,32P,400
IC601 BH13-00004A IC-HYBRID DP104S,T0-220-52,5P,POWER SW
IC602 1203-000165 IC-POSI.ADJUSTREG. 78R12,TO-220,3P,1
IC603 1201-000229 IC-OPAMP 324,DIP,14P,300MIL,QUAD,100V/m
IC604 1203-000001 IC-POSI.FIXEDREG. 7805,TO-220,3P,-,PLAST
IC605 1203-000495 IC-RESET 7045,T0-92,3P,-,PLASTIC,4.3/4
L401 BH27-20345B COIL-CHOKE 150uH,10%,DR1415(L-81,C:8.0)
L402 BH27-00005A COIL-CHOKE 120UH,10%,AR-06*30,BULK
L403 BH27-20343H COIL-PEAKING 2.7MH,10%,DR8*8,TP
L601 BH27-00007A COIL-LINEFILTER 25MHMIN,-,SQE2424,BUL
OP201 0601-001147 LED ROUND,GRN,4.75mm,565nm
Q301 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP
Q302 0501-000303 TR-SMALLSIGNAL KSA733,PNP,250mW,TO-92,TP
Q303 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP
Q401 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP
Q402 0505-001309 FET-SILICON IRF630,N,200V,10A,0.4OHM,100
Q403 0501-000372 TR-SMALLSIGNAL KSC2383-Y,NPN,900mW,TO-92
Q404 0502-001129 TR-POWER KSC5802,NPN,70W,TO-3PF,ST,5
Q405 0501-000303 TR-SMALLSIGNAL KSA733,PNP,250mW,TO-92,TP
Q406 0501-000303 TR-SMALLSIGNAL KSA733,PNP,250mW,TO-92,TP
Q407 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP
Q408 0502-000465 TR-POWER KTD2058-Y,NPN,25W,TO-220IS,ST
Q409 0505-001309 FET-SILICON IRF630,N,200V,10A,0.4OHM,100
Q410 0505-001309 FET-SILICON IRF630,N,200V,10A,0.4OHM,100
Q412 0501-000404 TR-SMALLSIGNAL KSD1616-Y,NPN,750mW,TO-92
Q413 0501-000321 TR-SMALLSIGNAL KSB1116-Y,PNP,0.75W,TO-92
Q414 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP
Q415 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP
Q416 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP
Q501 0501-000416 TR-SMALLSIGNAL KSP92,PNP,625mW,TO-92,TP
Q502 0501-000143 TR-SMALLSIGNAL 2N6520,PNP,625mW,TO-92
Q503 0501-000303 TR-SMALLSIGNAL KSA733,PNP,250mW,TO-92,TP
Q551 0501-000413 TR-SMALLSIGNAL KSP44,NPN,625mW,TO-92,5 17”
Q601 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP
Q602 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP
Q604 0501-000404 TR-SMALLSIGNAL KSD1616-Y,NPN,750mW,TO-92
Q608 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP
Q609 0501-002228 TR-SMALLSIGNAL KTA1281,PNP,1000MW,TO-92
Q610 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP
R200 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM

!

!

7 Electrical Parts List

DP15H*/DP17L* 7-5

R201 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R202 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R203 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R204 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R206 2001-000515 R-CARBON 220OHM,5%,1/8W,AA,TP,1.8X3.2MM
R207 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM
R208 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM
R209 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R210 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R211 2001-000904 R-CARBON 620OHM,5%,1/8W,AA,TP,1.8X3.2MM 17”
R211 2001-000924 R-CARBON 680OHM,5%,1/8W,AA,TP,1.8X3.2MM 15”
R212 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R213 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R214 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R215 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R216 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R217 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R218 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R219 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R220 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R221 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R222 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R223 2001-000038 R-CARBON 390OHM,5%,1/4W,AA,TP,2.4X6.4MM
R224 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM
R225 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM
R229 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R230 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R231 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R232 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R233 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R234 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R235 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R236 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R301 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM
R302 2004-000580 R-METAL 22Kohm,1%,1/4W,AA,TP,2.4x6.4mm
R303 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R304 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R306 2004-001022 R-METAL 5.6Kohm,1%,1/4W,AA,TP,2.4x6.4m
R307 2001-001053 R-CARBON(S) 1.5OHM,5%,1/2W,AA,TP,2.4X6.4
R308 2001-001088 R-CARBON(S) 1KOHM,5%,1/2W,AA,TP,2.4X6.4M
R309 2004-004014 R-METAL 2.4ohm,1%,1/4W,AA,TP,2.4x6.4mm 17”
R309 2004-004424 R-METAL 3.0ohm,1%,1/4W,AA,TP,2.4x6.4mm 15”
R310 2004-001136 R-METAL 6.8Kohm,1%,1/4W,AA,TP,2.4x6.4m
R311 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R312 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R315 2004-004014 R-METAL 2.4ohm,1%,1/4W,AA,TP,2.4x6.4mm 17” SDD,TSB
R315 2004-001816 R-METAL 3.3ohm,1%,1/4W,AA,TP,2.4x7mm 15” PHS

7 Electrical Parts List

7-6 DP15H*/DP17L*

Loc. No. Code No. Description Specification Remarks

Loc. No. Code No. Description Specification Remarks

R316 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R317 2001-000561 R-CARBON 27KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R318 2001-000766 R-CARBON 43KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R319 2001-000947 R-CARBON 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R320 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R321 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R322 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R323 2001-000022 R-CARBON(S) 33OHM,5%,1/2W,AA,TP,2.4X6.4M
R324 2001-000660 R-CARBON 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R325 2003-000805 R-METALOXIDE(S) 82ohm,5%,1W,AA,TP,3.3x9m
R326 2003-000805 R-METALOXIDE(S) 82ohm,5%,1W,AA,TP,3.3x9m
R402 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM
R403 2004-001226 R-METAL 750ohm,1%,1/4W,AA,TP,2.4x6.4mm
R404 2004-000498 R-METAL 2.7Kohm,1%,1/4W,AA,TP,2.4x6.4m
R405 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R406 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R407 2001-000109 R-CARBON(S) 470OHM,5%,1/2W,AA,TP,2.4X6.4
R408 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R409 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R410 2003-000650 R-METALOXIDE(S) 330ohm,5%,2W,AA,TP,4x12m
R411 2001-001096 R-CARBON(S) 2.2OHM,5%,1/2W,AA,TP,2.4X6.4
R412 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R413 2001-001038 R-CARBON(S) 0.56OHM,5%,1/2W,AA,TP,2.4X6
R414 2001-001038 R-CARBON(S) 0.56OHM,5%,1/2W,AA,TP,2.4X6
R415 2003-000429 R-METALOXIDE(S) 1.5Kohm,5%,2W,AA,TP,4x12
R416 2001-000107 R-CARBON(S) 150KOHM,5%,1/2W,AA,TP,2.4X6.
R417 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM SDD
R417 2001-000890 R-CARBON 62KOHM,5%,1/8W,AA,TP,1.8X3.2MM TSB, PHS
R418 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R418 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15”
R419 2001-000397 R-CARBON 180KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R420 2001-000354 R-CARBON 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM 17”
R420 2004-000327 R-METAL 150Kohm,1%,1/4W,AA,TP,2.4x6.4m 15”
R422 2001-001006 R-CARBON 82OHM,5%,1/8W,AA,TP,1.8X3.2MM
R423 2001-000258 R-CARBON 1.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R423 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15”
R424 2004-000284 R-METAL 12Kohm,1%,1/4W,AA,TP,2.4x6.4mm
R425 2001-000044 R-CARBON 1.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM 17”
R425 2001-000042 R-CARBON 1KOHM,5%,1/4W,AA,TP,2.4X6.4MM 15”
R426 2001-000110 R-CARBON 10OHM,5%,1/4W,AA,TP,2.4X6.4MM
R427 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R428 2003-000653 R-METALOXIDE(S) 330ohm,5%,3W,AA,TP,6x16m 17”
R428 2003-000608 R-METALOXIDE(S) 270ohm,5%,3W,AA,TP,6x16m 15”
R429 2001-000052 R-CARBON(S) 3.3KOHM,5%,1/2W,AA,TP,2.4X6
R430 2001-001078 R-CARBON(S) 15KOHM,5%,1/2W,AA,TP,2.4X6.4
R431 2003-000407 R-METALOXIDE(S) 0.6ohm,5%,2W,AA,TP,4x12m 17”

!

!

7 Electrical Parts List

DP15H*/DP17L* 7-7

R431 2005-001071 R-WIREWOUND 0.82OHM,5%,3W,AA,TP,5.5X15M 15”
R432 2001-000020 R-CARBON(S) 22OHM,5%,1/2W,AA,TP,2.4X6.4M
R434 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R435 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R436 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R437 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R438 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 17”
R438 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15”
R439 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 17”
R440 2001-000947 R-CARBON 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R441 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R443 2003-000502 R-METALOXIDE(S) 150ohm,5%,2W,AA,TP,4x12m 17”
R443 2003-000578 R-METALOXIDE(S) 220ohm,5%,2W,AA,TP,4x12m 15”
R444 2003-000767 R-METALOXIDE(S) 680ohm,5%,2W,AA,TP,4x12m
R445 2001-000019 R-CARBON(S) 10OHM,5%,1/2W,AA,TP,2.4X6.4M
R446 2001-000117 R-CARBON(S) 68OHM,5%,1/2W,AA,TP,2.4X6.4M 17”
R446 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6 15”
R446 2001-000028 R-CARBON(S) 100OHM,5%,1/2W,AA,TP,2.4X6.4 15”
R447 2003-000777 R-METALOXIDE(S) 68ohm,5%,2W,AA,TP,4x12mm
R448 2003-000777 R-METALOXIDE(S) 68ohm,5%,2W,AA,TP,4x12mm
R449 2001-000211 R-CARBON 1OHM,5%,1/4W,AA,TP,2.4X6.4MM
R450 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R451 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R452 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R453 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R454 2003-000650 R-METALOXIDE(S) 330ohm,5%,2W,AA,TP,4x12m
R500 2001-000435 R-CARBON 1MOHM,5%,1/8W,AA,TP,1.8X3.2MM
R501 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R502 2004-000979 R-METAL 47Kohm,1%,1/4W,AA,TP,2.4x6.4mm
R503 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 17”
R504 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R505 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R506 2004-000657 R-METAL 27Kohm,1%,1/4W,AA,TP,2.4x6.4mm
R507 2004-000216 R-METAL 10Kohm,1%,1/4W,AA,TP,2.4x6.4mm
R508 2001-001052 R-CARBON(S) 1.5MOHM,5%,1/2W,AA,TP,2.4X6
R509 2001-001052 R-CARBON(S) 1.5MOHM,5%,1/2W,AA,TP,2.4X6
R510 2001-000837 R-CARBON 51KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R511 2001-000478 R-CARBON 2.7OHM,5%,1/4W,AA,TP,2.4X6.4MM
R512 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R513 2001-001115 R-CARBON(S) 27KOHM,5%,1/2W,AA,TP,2.4X6.4
R514 2001-000837 R-CARBON 51KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R515 2001-000546 R-CARBON 270KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R516 2004-000368 R-METAL 160KOHM,5%,1/4W,AA,TP,2.4X6.4MM SDD
R516 2004-000398 R-METAL 180KOHM,5%,1/4W,AA,TP,2.4X6.4MM TSB, PHS
R516 2004-000327 R-METAL 150Kohm,1%,1/4W,AA,TP,2.4x6.4m 15”
R517 2001-000987 R-CARBON 820KOHM,5%,1/4W,AA,TP,2.4X6.4MM

!!!!!

!

7 Electrical Parts List

7-8 DP15H*/DP17L*

Loc. No. Code No. Description Specification Remarks

Loc. No. Code No. Description Specification Remarks

R518 2001-001031 R-CARBON 91KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R519 2001-000356 R-CARBON 150KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R520 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R520 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15”
R521 2008-001085 R-FUSIBLE 4.7KOHM,5%,1/4W,AA,TP,2.4X6MM
R524 2001-000660 R-CARBON 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R525 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R526 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R526 2001-000908 R-CARBON 62KOHM,5%,1/8W,AA,TP,1.8X3.2MM 17”
R527 2001-000864 R-CARBON 56KOHM,5%,1/8W,AA,TP,1.8X3.2MM 17”
R527 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15”
R527 2001-000837 R-CARBON 62KOHM,5%,1/8W,AA,TP,1.8X3.2MM TSB, PHS
R527 2001-000908 R-CARBON 51KOHM,5%,1/8W,AA,TP,1.8X3.2MM SDD
R528 2001-000262 R-CARBON 1.8MOHM,5%,1/8W,AA,TP,1.8X3.2MM
R529 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R551 2001-000530 R-CARBON 240KOHM,5%,1/4W,AA,TP,2.4X6.4MM 17”
R552 2001-000537 R-CARBON 24KOHM,5%,1/4W,AA,TP,2.4X6.4MM 17”
R553 2001-001129 R-CARBON(S) 330KOHM,5%,1/2W,AA,TP,2.4X6 17”
R554 2001-001110 R-CARBON(S) 240KOHM,5%,1/2W,AA,TP,2.4X6 17”
R555 2001-000042 R-CARBON 1KOHM,5%,1/4W,AA,TP,2.4X6.4MM 17”
R556 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 17”
R600 2001-001129 R-CARBON(S) 330KOHM,5%,1/2W,AA,TP,2.4X6
R601 2001-001129 R-CARBON(S) 330KOHM,5%,1/2W,AA,TP,2.4X6
R602 2001-000023 R-CARBON 47OHM,5%,1/4W,AA,TP,2.4X6.4MM
R603 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R604 2001-000857 R-CARBON 560OHM,5%,1/8W,AA,TP,1.8X3.2MM
R605 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R606 2003-000225 R-METALOXIDE 22Kohm,5%,1W,AA,TP,4.3x12m
R607 2003-000225 R-METALOXIDE 22Kohm,5%,1W,AA,TP,4.3x12m
R608 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R609 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6
R610 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6
R611 2001-001079 R-CARBON(S) 15OHM,5%,1/2W,AA,TP,2.4X6.4M
R612 2003-000738 R-METALOXIDE(S) 56Kohm,5%,2W,AA,TP,4x12m
R614 2001-001107 R-CARBON(S) 220ohm,5%,1/2W,AA,TP,2.4x6.4
R615 2001-001088 R-CARBON(S) 1KOHM,5%,1/2W,AA,TP,2.4X6.4M
R617 2001-001037 R-CARBON(S) 0.39OHM,5%,1/2W,AA,TP,2.4X6. SDD, TSB
R617 2001-001038 R-CARBON(S) 0.56OHM,5%,1/2W,AA,TP,2.4X6 PHS
R618 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R619 2003-000471 R-METALOXIDE(S) 10ohm,5%,2W,AA,TP,4x12mm
R620 2001-000354 R-CARBON 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R621 2001-000989 R-CARBON 820KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R622 2001-000211 R-CARBON 1OHM,5%,1/4W,AA,TP,2.4X6.4MM
R625 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R630 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R631 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R632 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM

!!!

7 Electrical Parts List

DP15H*/DP17L* 7-9

R633 2001-000211 R-CARBON 1OHM,5%,1/4W,AA,TP,2.4X6.4MM
RL601 3501-001111 RELAY-POWER 12Vdc,250mW,5A,1FormA,15mS,5
SK501 4715-000001 SURGEABSORBER 1KV,+50-10%,
SW201 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP
SW202 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP
SW203 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP
SW204 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP
SW401 3406-000002 SWITCH-ROTARY 36Vdc,200mA,SP3T
SW601 3403-001050 SWITCH-PUSH 30V,0.3A,SPDT,ON-OFF,PCBORD
T401 BH26-00027A TRANS-HOR.DRIVE 35.0MH,-,EI1916,PL-3
T402 BH26-00028A TRANS-H.LINEARITY 5.2UH,6P,DR1425(C:5.0) 17”
T402 BH26-00029A TRANS-H.LINEARITY 6.5UH,-,DR1425(C:5.0), 15”
T501 BH26-00035A TRANS-FBT 1.0MH,13P,FUR3658,HV45,FM1 17”
T501 BH26-00025A TRANS-FBT 1.0MH,13P,3763SU,SM9C,FQA- 15”
T502 BH26-00022A TRANS-FOCUS 3.0MH,6P,EI2218,SB-5S,3.0MH 17”
T502 BH26-00023A TRANS-FOCUS 5.0MH,6P,EI2218,SB-5S,5.0MH 15”
T601 BH26-00033A TRANS-SWITCHING 390UH,16P,EER3538,PL3,P 17”
T601 BH26-00032A TRANS-SWITCHING 390UH/83UH,16P,EER3538S 15”
T602 BH26-30302S TRANS-SYNC. 3-1(250UH),SB-5S,UU1116
TH601 1404-000002 THERMISTOR-PTC 9ohm,20%,TR,RECT
TH602 1404-001020 THERMISTOR-NTC 8ohm,15%,17mW/C,BK
TP501 4715-000001 SURGEABSORBER 1KV,+50-10%
X201 2801-000005 CRYSTAL-UNIT 8MHz,50ppm,28-AAM,S,35ohm,T
ZD201 0403-000355 DIODE-ZENER UZ5.1BSB,5.1V,4.97-5.18V,500
ZD202 0403-000355 DIODE-ZENER UZ5.1BSB,5.1V,4.97-5.18V,500
ZD203 0403-000355 DIODE-ZENER UZ5.1BSB,5.1V,4.97-5.18V,500
ZD204 0403-000355 DIODE-ZENER UZ5.1BSB,5.1V,4.97-5.18V,500
ZD205 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500
ZD502 0403-001068 DIODE-ZENER UZ4.7BSA,4.7V,4.47-4.65V,500
ZD601 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500

!!!!!!!!!!!

7 Electrical Parts List

7-10 DP15H*/DP17L*

Loc. No. Code No. Description Specification Remarks

Loc. No. Code No. Description Specification Remarks

BD102 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500
BD103 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500
C101 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
C102 2401-001334 C-AL 470nF,20%,50V,GP,TP,5x11,2.5
C103 2401-000037 C-AL 470uF,20%,16V,GP,TP,8x11.5,5
C104 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V
C105 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
C106 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
C107 2401-000010 C-AL 220uF,20%,16V,GP,6.3x11mm,2
C108 2401-001459 C-AL 47uF,20%,100V,GP,TP,10x16.5,5
C109 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V
C110 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5
C111 2401-000031 C-AL 47uF,20%,16V,GP,TP,5x11,5
C112 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5
C113 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
C114 2301-000231 C-FILM,PEF 3.3nF,5%,100V,TP,5.8x12.5mm,5
C116 2301-000188 C-FILM,PEF 1nF,5%,100V,TP,10.5x12.5x6.5
C117 2301-000188 C-FILM,PEF 1nF,5%,100V,TP,10.5x12.5x6.5
C118 2201-000471 C-CERAMIC,DISC .33NF,10%,50V,Y5P,TP,4X3M
C119 2201-000291 C-CERAMIC,DISC 1nF,10%,500V,Y5P,TP,8.5x5
C120 2201-000285 C-CERAMIC,DISC 1nF,10%,1KV,Y5P,TP,10x5,5
C121 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm
C123 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm
C124 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm
C125 2401-000010 C-AL 220uF,20%,16V,GP,6.3x11mm,2
CB01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
CB02 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
CB04 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm
CB05 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm
CB06 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
CG01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
CG02 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
CG03 2201-000483 C-CERAMIC,DISC 33pF,5%,50V,CH,TP,5x3,5
CG04 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm
CG05 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm
CG06 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
CN101 3711-004228 CONNECTOR-HEADER BOX,6P,1R,2MM,ANGLE,SN
CN102 BH39-00015A CBF-HARNESS 13P/14P,200MM,WHT/BLK/RED/BL
CR01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
CR02 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
CR04 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm
CR05 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm
CR06 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5
D101 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
D102 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
DB01 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
DB02 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T

7 Electrical Parts List

DP15H*/DP17L* 7-11

7-2 Video PCB Parts

DB03 0401-000004 DIODE-SWITCHING 1SS244,250V,200mA,DO-34
DB04 0401-000004 DIODE-SWITCHING 1SS244,250V,200mA,DO-34
DB05 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
DG01 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
DG02 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
DG03 0401-000004 DIODE-SWITCHING 1SS244,250V,200mA,DO-34
DG04 0401-000004 DIODE-SWITCHING 1SS244,250V,200mA,DO-34
DG05 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
DR01 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
DR02 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
DR03 0401-000004 DIODE-SWITCHING 1SS244,250V,200mA,DO-34
DR04 0401-000004 DIODE-SWITCHING 1SS244,250V,200mA,DO-34
DR05 0401-000005 DIODE-SWITCHING 1N4148,75V,200MA,DO-35,T
HS103 BH99-00004B ASSY,HEAT/SINK H/S VIDEO,SCREW+NUT,LM243
IC101 1201-001332 IC-VIDEO AMP 2506,DIP,28P,600MIL,SINGLE
IC103 BH13-00003A IC-HYBRID LM2437,TO-220,9P,CRT DRIVER
IC104 1204-001529 IC-OSD PROCESSOR KS2501-09,DIP,24P,300MI
LB01 2701-000190 INDUCTOR-AXIAL 470nH,20%,4x9.8mm
LG01 2701-000190 INDUCTOR-AXIAL 470nH,20%,4x9.8mm
LJP1 BH39-40306D CBF-HARNESS 80MM,BLK,1015,AWG22
LR01 2701-000190 INDUCTOR-AXIAL 470nH,20%,4x9.8mm
Q101 0501-000122 TR-SMALL SIGNAL 2N3904,NPN,625mW,TO-92,T
Q102 0501-000122 TR-SMALL SIGNAL 2N3904,NPN,625mW,TO-92,T
QB01 0501-000140 TR-SMALL SIGNAL 2N5551,NPN,625mW,TO-92
QB02 0501-000138 TR-SMALL SIGNAL 2N5401,PNP,625mW,TO-92,T
QG01 0501-000140 TR-SMALL SIGNAL 2N5551,NPN,625mW,TO-92
QG02 0501-000138 TR-SMALL SIGNAL 2N5401,PNP,625mW,TO-92,T
QR01 0501-000140 TR-SMALL SIGNAL 2N5551,NPN,625mW,TO-92
QR02 0501-000138 TR-SMALL SIGNAL 2N5401,PNP,625mW,TO-92,T
R101 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R102 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R103 2001-001138 R-CARBON(S) 390OHM,5%,1/2W,AA,TP,2.4X6.4
R104 2001-001138 R-CARBON(S) 390OHM,5%,1/2W,AA,TP,2.4X6.4
R105 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R106 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R107 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R108 2001-000857 R-CARBON 560OHM,5%,1/8W,AA,TP,1.8X3.2MM
R109 2001-000857 R-CARBON 560OHM,5%,1/8W,AA,TP,1.8X3.2MM
R110 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R111 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R113 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R114 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MM
R115 2001-000001 R-CARBON 2Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R116 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R117 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R118 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R119 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM

7 Electrical Parts List

7-12 DP15H*/DP17L*

Loc. No. Code No. Description Specification Remarks

Loc. No. Code No. Description Specification Remarks

R141 2001-000005 R-CARBON 390OHM,5%,1/8W,AA,TP,1.8X3.2MM
R142 2001-000005 R-CARBON 390OHM,5%,1/8W,AA,TP,1.8X3.2MM
R143 2001-000005 R-CARBON 390OHM,5%,1/8W,AA,TP,1.8X3.2MM
R144 2001-000005 R-CARBON 390OHM,5%,1/8W,AA,TP,1.8X3.2MM
RB01 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM
RB02 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM
RB03 2001-000005 R-CARBON 390OHM,5%,1/8W,AA,TP,1.8X3.2MM
RB04 2001-000302 R-CARBON 10OHM,5%,1/8W,AA,TP,1.8X3.2MM
RB08 2001-000027 R-CARBON 100OHM,5%,1/4W,AA,TP,2.4X6.4MM
RB09 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM
RB10 2001-000705 R-CARBON 39OHM,5%,1/2W,AA,TP,3.3X9MM
RB11 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
RB12 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
RB13 2001-001000 R-CARBON 82KOHM,5%,1/8W,AA,TP,1.8X3.2MM
RG01 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM
RG02 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM
RG03 2001-000005 R-CARBON 390OHM,5%,1/8W,AA,TP,1.8X3.2MM
RG04 2001-000302 R-CARBON 10OHM,5%,1/8W,AA,TP,1.8X3.2MM
RG05 2001-000004 R-CARBON 200KOHM,5%,1/8W,AA,TP,1.8X3.2MM
RG08 2001-000027 R-CARBON 100OHM,5%,1/4W,AA,TP,2.4X6.4MM
RG09 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM
RG10 2001-000705 R-CARBON 39OHM,5%,1/2W,AA,TP,3.3X9MM
RG11 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
RG12 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
RG13 2001-001000 R-CARBON 82KOHM,5%,1/8W,AA,TP,1.8X3.2MM
RR01 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM
RR02 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM
RR03 2001-000005 R-CARBON 390OHM,5%,1/8W,AA,TP,1.8X3.2MM
RR04 2001-000302 R-CARBON 10OHM,5%,1/8W,AA,TP,1.8X3.2MM
RR08 2001-000027 R-CARBON 100OHM,5%,1/4W,AA,TP,2.4X6.4MM
RR09 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM
RR10 2001-000705 R-CARBON 39OHM,5%,1/2W,AA,TP,3.3X9MM
RR11 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
RR12 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
RR13 2001-001000 R-CARBON 82KOHM,5%,1/8W,AA,TP,1.8X3.2MM
S/VID 6502-000001 CABLE CLAMP DAWH-5NB,D15,L35,NTR,NYLON66
S/VID+H/S 6003-000010 SCREW-TAPTITE BWH,+,B,M3,L10,ZPC(YEL),SW
SK01 3704-001088 SOCKET-CRT 13P,22.5PI,25.6PI,SN
SK101 1405-001064 SURGE ABSORBER 400V,20%,AXIAL
SK102 4715-000001 SURGE ABSORBER 1KV,+50-10%
SKB01 4715-000102 SURGE ABSORBER 200V,20%,1000A,RADIAL
SKG01 4715-000102 SURGE ABSORBER 200V,20%,1000A,RADIAL
SKR01 4715-000102 SURGE ABSORBER 200V,20%,1000A,RADIAL

7 Electrical Parts List

DP15H*/DP17L* 7-13

7 Electrical Parts List

DP15H*/DP17L* 7-14

CRT BH03-00005A CRT-COLOR 0.28,M36LGE128X208(F1M1),SINGLE 15”

BH03-10341F CRT-COLOR 0.28,M36LGE128X206,SINGLE 15”
BH03-00015A CRT-COLOR 0.28,M41QAR361X114(T4/S-2),DYNA 17”
BH03-10342B CRT-COLOR 0.28,M41QAR361X111(A/S2),D 17”

PBA UNIT BH94-00048B ASSY,PCB DP15H*

BH94-00048C ASSY,PCB DP17L*

B/D ASS’Y CODE BH98-00036B ASSY,PCB/MAIN DP15H*

BH98-00037B ASSY,PCB/VIDEO DP15H*
BH98-00036C1 ASSY,PCB/MAIN DP17L*

BH98-00037C ASSY,PCB/VIDEO DP17L*
S/CABLE BH39-00016A CBF-SIGNAL 1550MM,IVORY(IV01),2990
MAGNET 3302-000006 MAGNET-RUBBER AF,14G,1620-1980G,0.58-0.9
D/COIL BH27-00014A COIL DEGAUSSING-ASS’Y 290*225*1020MM,6.9 15”

BH27-00015A COIL DEGAUSSING-ASS’Y 290*265*1100MM,9.6 17”
P/CORD BH39-10007A CBF POWER/CORD DET,H05VV-F,250V/6A,IVY,1830MM

BH39-10339E CBF POWER/CORD DET,SVT,125V 7A/10A,IVY,1830MM

Loc. No. Code No. Description Specification Remarks

Others

!

7 Electrical Parts List

7-15 DP15H*/DP17L*

7-3 Different Parts List (CDT)

Memo

7 Electrical Parts List

DP15H*/DP17L* 7-16

8 Block Diagrams

DP15H*/DP17L* 8-1

SCREE

N

RGB

VIDEO BOARD

TO D-COIL

ON THE CRT

VIDEO INPUT

H/V SYNC

VIDEO OUTPUT

IC103(LM2437)

RGB - CUTOFF

QR, G,B01,02

G1

HEATER

VIDEO PRE-AMP

+ OSD

IC101(KA2506)

IC104(KA2501)

SOCKET

FBT

T501

H/V SIZE

REG.

VERTICAL

FOCUS

HOR. DY

CN401

VER. DY

CN401

H. D. T

T401

S-COR.

VER. OUTPUT

IC301

HOR. DRIVE

Q403

HOR./VER.

PROCESSOR

IC401

H-SYNC1

V-SYNC1

E/W_OUT

12C DATA

12C CLK

REG.

V-MUTE

S-CORRECTION

PS-1(SUSPEND)

PS-2(POWER OFF)

HOR. LINEARITY

TILT

POWER

PWM CONTROL

IC601C

BRIDGE

RETIFIER

EPROM

IC202

DEGAUSSING

BLOCK

RL601

UP, DOWN

BRIGHTNISS

CONTRASTER

PIN, TRAP

SIZE, POSI,

DEGA.

LED

POWER

AC INPUT

SOCKET

CN601

LINE

FILTER

L601

SWITCHING

TRANS

T601

ACL

CIRCUIT

CONTRAST

CONTROL

BRIGHTNESS

CONTROL

+56V

+13V

-12V

+6.3V

+70V

PS-2

VER.OUT & TILT CONTORL

HEA TER VOLT A GE CONTROL

POWER-OFF MODE CONTROL

Q607

+12V REGULATOR

PS-1, PS-2(From MCU)

CRT HEATER

G1

+12V

TO VIDEO

-210V

+30V

+12V

CONTRAST

CONTROL

BRIGHTNESS

CONTROL

-210V
(FROM FBT)

VER. BLANKING

Q303

KSC945

24LC04

FROM MCU

B(+)

FROM IC401

H-SYNC, V-SYNC

TDA4859

KA2142

FRONT CONTROL

BOARD

SIGNAL

MAIN BOARD

H/V

FOCUS

MCU

IC201

HOR. OUT

Q404

DYNAMIC FOCUS

T502

KSC5802

Memo

8 Block Diagrams

8-2 DP15H*/DP17L*

DP15H*/DP17L* 9-1

1
2

3

H +

V +

4

V–

1
2

3

1
2

3

(YEL)V+

NC

(Brown)V –

V +
NC
V –

CN401

12AC

AC

1
2

AC
AC

1
2

3

AC INPUT
NC
AC INPUT

TILT

9

10
11
12
13

1
2

3
4
5
6
7
8

FBT

15 PIN

D-SUB

refer to pin

assignment

of

product spec.

DEGAUSSING COIL

AC INPUT

CRT SOCKET

G2

CN402
CN302

CN303

CN301

GT601
GT602

CN601

MAIN PCB

CRT SOCKET PCB

FOCUS
(WHT)

1

2

3

1

2

3

NC

TILT–(BLK)

TILT +

NC

TILT –

H–

H +

NC

H–

NC

1
2

3
4

TILT+(WHT)

70 V

IICCLK

CLAMP
5 V

GND

GND

6.3 V
G1

12 V

V-SYNC
ACL

IICDATA

AFC

9

10
11
12
13
14

1
2

3
4
5
6
7
8

(RED) H+

(BLUE) H-

(YEL) V+

(BROWN)V-

NC

TCO +

TCO – (GND)

NC

TCO +

TCO – (GND)

CN502

15"/17" PHS CDT

15" TSB CDT

12V+

V–

H+
NC

NC

H–

2 x 3p DY 15"/17" 15"/17"

FOCUS1 (WHT)
FOCUS2 (RED)

CN304

CN501

CN201

GND

H-IN

DDC CLK

DDC 5V

S-RASTER

DDC DATA

V-IN

1

2

3

4

5

6

7

CN202

GND

H-IN

DDC CLK

DDC 5V

S-RASTER

DDC DATA

V-IN

1

2

3

4

5

6

7

70 V
GND

6.3 V

IICCLK
CLAMP
5 V

GND

G1

12 V

V-SYNC
ACL

IICDATA

AFC

BLANK

1

2

3

4

5

6

CN101

R

GND

GND

G

GND

B

1

2

3

4

5

6

SIGNAL CABLE

R_IN

GND_R

GND_G

G_IN

GND_B

B_IN

2 x 3p DY

CN102

9 Wiring Diagram

10-1 DP15H*/DP17L*

10 Schematic Diagrams

10-1 SMPS Part Schematic Diagram

10 Schematic Diagrams

DP15H*/DP17L* 10-2

1
2
3
4
5

285 V

0.8 mV

18.1 V

1.51 V

4.98 V

286 V

0.6 mV

18.0 V

2.01 V

4.98

pin #

MODES

1024 x 768 / 85 Hz 640 x 480 / 60 Hz

Table 10-1. IC601 (DP104C)

Unit: Vrms

1
2
3
4

13.57 V

12.05

-17.0 mV

4.99 V

13.50

12.05

-15.5 mV

4.99 V

pin #

MODES

1024 x 768 / 85 Hz 640 x 480 / 60 Hz

Table 10-2. IC602 (78R12)

Unit: Vrms

1

100V (IC601, #1)

CH1 P-P = 100V CH1 RMS = 350.2 V

2

100V (IC601, #1)

CH1 P-P = 100V CH1 RMS = 325.8V

10 Schematic Diagrams

10-3 DP15H*/DP17L*

10-2 Micom Part Schematic Diagram

10 Schematic Diagrams

DP15H*/DP17L* 10-4

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21

5.01 V

5.01 V

5.01 V

-4.9 mV

5.00 V

4.9 V

31.2 mV

7.96 mV

9.1 mV

9.9 mV

5.12 V

15.3 mV

1.13 V

1.68 V

15.5 mV

4.13 mV ~ 3.9 V

3.66 V

4.99 V

4.31 V

2.49 V

2.44

0.47 mV

-2.0 mV

-3.2 mV

-4.4 mV

5.00 V

4.90 V

30.8 mV

-7.4 mV

-8.5 mV

-9.4 mV

5.12 V

-14.5 mV

1.13 V

1.70 V

-14 mV

41.3 V ~ 3.9 V

3.67 V

4.99 V

4.34 V

2.49 V

0.6 V

1.02 V

2.91 V

1.14 V

7.5 mV

3.99 V

4.93 V

4.73 V

11.3 mV

4.5 mV

0.314 V

15.3 mV

15.6 mV

5.12 V

5.11 V

5.11 V

5.11 V

5.11 V

5.11 V

0.145 V

5.12 V

5.12

1.02 V

0.31 V

1.04 V

-8.7 mV

3.99 V

5.0 V

4.49 V

-11.4 mV

4.49 V

3.98 V

-14.6 mV

-14.8 mV

5.12 V

5.11 V

5.11 V

5.11 V

5.11 V

5.11 V

0.146 V

5.12 V

5.12 V

22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42

pin #

pin #

MODES

1024 x 768 / 85 Hz 1024 x 768 / 85 Hz640 x 480 / 60 Hz 640 x 480 / 60 Hz

MODES

Table 10-3. IC201 (KS88C623IN)

Unit: Vrms

18

1.00 V (IC201, #13, 14)

CH1 P-P = 1.00 V CH1 RMS = 2.108 V

10 Schematic Diagrams

10-5 DP15H*/DP17L*

10-3 H/V OSC & Vertical Part Schematic Diagram

10 Schematic Diagrams

DP15H*/DP17L* 10-6

pin #

1

2

3

4

5

6

7

8

9
10

0.64

13.2

1.5 mV

-10.5

-11.0

-3.9 mV
0 mV

0.1 mV

12.9 V

0.64 V

0.64

13.0

0.1 mV

-10.6

-10.9

-1.6 mV

0.1 mV

0.1 mV

12.6 V

0.64 V

pin #

MODES

800 x 600 / 85 Hz 640 x 480 / 60 Hz

Table 10-5. IC301 (KA2142)

Unit: Vrms

1
2
3
4
5
6
7
8

9
10
11
12
13
14

12.01

3.06

5.12

13.5

5.12

5.12

6.51

0.66

1.63

1.63

11.19

1.63

1.63

0.70

11.8

3.60

5.12

13.3

5.11

5.12

6.43

3.96

1.63

1.63

-11.1

1.63

1.63

-0.68

pin #

MODES

1024 x 768 / 85 Hz 640 x 480 / 60 Hz

Table 10-6. IC603 (LM324N)

Unit: Vrms

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16

0.33 V

5.64 V

4.45 V

2.15 V

2.48 V

3.54 V

-15.4 mV

0.964 V

2.01 V

11.7 V

2.73 V

1.38 V

1.29 V

-11.3 mV

4.73 V

0.76 V

-0.15 V

5.68 V

3.89 V

1.39 V

2.48 V

6.48 V

-14.5 mV

0.93 V

2.02 V

11.7 V

1.86 V

1.38 V

1.29 V

-11.4 mV

4.49 V

0.64 V

pin #

MODES

1024 x 768 85 Hz 640 x 480 / 60 Hz

17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

24.7 mV

5.12 V

5.12 V

4.02 V

5.01 V

2.69 V

3.02 V

2.66

-15.4 mV

3.86 V

1.54 V

2.57 V

4.54 V

5.47 V

5.47 V

6.11 V

23.9 mV

5.12 V

5.12 V

4.04 V

5.01 V

3.17 V

3.03 V

2.67 V

-14.7 mV

3.86 V

2.51 V

2.56V

4.51 V

5.00 V

4.99

6.08

MODES

1024 x 768 85 Hz 640 x 480 / 60 Hz

Table 10-7 IC401 (TDA4859)

Unit: Vrms

3

2.00 V(IC401, #6)

CH1 P-P = 2.00 V CH1 RMS = 5.868 V

4

1.00 V (IC401, #8)

CH1 P-P = 1.00 V CH1 RMS = 1.298 V

7

1.00 V (IC401, #11)

CH1 P-P = 1.00 V CH1 RMS = 3.008 V

8

500 V (IC401, #12)

CH1 P-P = 500 V CH1 RMS = 1.425 V

9

10.0 V (IC301, #6)

CH1 P-P = 10.0 V CH1 RMS = 5.06 V

12

2.00 V (IC401, #32)

CH1 P-P = 2.00 V CH1 RMS = 6.124 V

10 Schematic Diagrams

10-7 DP15H*/DP17L*

10-4 Deflection Part Schematic Diagram

10 Schematic Diagrams

DP15H*/DP17L* 10-8

13

50.0 V (T502, #6)

CH1 P-P = 50.0 V CH1 RMS = 75.6 V

14

100 V (T502, #1)

CH1 P-P = 100 V CH1 RMS = 124.0 V

11

50.0 V (Q402, Drain)

CH1 P-P = 50.0 V CH1 RMS = 73.7 V

10

2.00 V (Q402, Gate)

CH1 P-P = 2.00 V CH1 RMS = 7.692 V

6

200 V (Q408, Collector)

CH1 P-P = 200 V CH1 RMS = 387.2 V

5

20.0 V (Q403, Collector)

CH1 P-P = 20.0 V CH1 RMS = 46.80 V

23

5.00 V (Q303, Collector)

CH1 P-P = 5.00 V CH1 RMS = 28.33 V

10 Schematic Diagrams

10-9 DP15H*/DP17L*

10-5 Video Part Schematic Diagram

10 Schematic Diagrams

DP15H*/DP17L* 10-10

1
2
3
4
5
6
7
8

9
10
11
12
13
14

4.6 mV

4.5 mV

4.4 mV

4.0 mV

2.42 V

11.8 V

1.06 mV

2.42 V

11.85 V

2.41 V

1.44 mV

4.22 V

5.11 V

5.11 V

3.2 mV

3.2 mV

3.0 mV

2.8 mV

2.45 V

11.8 V

1.0 mV

2.44 V

11.8 V

2.43 V

1.39 mV

4.15 V

5.11 V

5.11 V

11.2 V

11.2 V

11.2 V

4.73 V

4.01 V

4.35 V

2.42

1.6 mV

11.8 V

2.40

4.29

2.55

4.31

99.1 mV

11.2 V

11.2 V

11.2 V

4.49 V

4.55 V

4.34 V

2.56 V

1.5 mV

11.8 V

2.53 V

4.27 V

2.68 V

4.29 V

99.5 mV

15
16
17
18
19
20
21
22
23
24
25
26
27
28

pin #

pin #

MODES

1024 x 768 / 85 Hz 1024 x 768 / 85 Hz640 x 480 / 60 Hz 640 x 480 / 60 Hz

MODES

Table 10-8. IC101 (KA2506)

Unit: Vrms

1

2

3

4

5

6

7

8

9

38.5

39.9

GND

2.4 V

2.55

11.8

2.4 V

72.8

42.5

36.9

38.1

GND

2.53

2.68

11.8

2.4 V

73.2

40.2

pin #

MODES

800 x 600 / 85 Hz 640 x 480 / 60 Hz

Table 10-9. IC103 (LM2437)

Unit: Vrms

1
2
3
4
5
6
7
8

9
10
11
12

1.3 mV

2.24 V

1.26 V

1.27 V

4.93

3.99

5.11

5.11
NC
NC
NC
NC

NC
NC
NC
NC

4.91

1.9 mV

4.9

5.3 V

5.5 V

5.6 V
NC

4.93

pin #

MODES

1024 x 768 / 85 Hz 640 x 480 / 60 Hz

Table 13-10. IC104 (KS2501 ~ 09)

Unit: Vrms

22

10.0 V ( R, G, B, Video )

CH1 P-P = 10.0 V CH1 RMS = 17.02 V

24

20.00 V (CRT, G1)

CH1 P-P = 20.0 V CH1 RMS = 66.68 V

19

1.00 V (IC104, #6)

CH1 P-P = 1.00 V CH1 RMS = 4.516 V

20

1.00 V (IC104, #17)

CH1 P-P = 1.00 V CH1 RMS = 5.024 V

21

1.00 V (IC101, #21. 24. 26)

CH1 P-P = 1.00 V CH1 RMS = 2.580 V

15

1.00 V (IC101, #5, 8, 10)

CH1 P-P = 1.00 V CH1 RMS = 2.452 V

16

1.00 V (IC101, #21,24,26)

CH1 P-P = 1.00 V CH1 RMS = 2.792 V

17

20.0 V (IC103, #1, 2, 3)

CH1 P-P = 20.0 V CH1 RMS = 40.52 V

10 Schematic Diagrams

10-11 DP15H*/DP17L*

Memo

Samsung Electronics Co., Ltd. May 1999
Printed in Korea
Code No.: BH68-00129A