SAMSUNG DIGIMAX 200 TEST MENU [Eng]

Page 1
DIGIMAX 200 TEST MENU
1. Set the mode dail to PC mode
2. After pressing the UP button of the direction button for 5 sec and power on at the same time.
3. Test menu will displaed on LCD as below;
TEST MENU
LCD / KEY / LED / BUZ SDRAM / SMC / P-CODE TFT / TV STROBE AF / MS FOCUS COLOR TEST BURN IN
LCD / KEY / LED / BUZ
TEST MENU
LCD / KEY / LED / BUZ
SDRAM / SMC / P-CODE TFT / TV STROBE AF / MS FOCUS COLOR TEST BURN IN
SDRAM / SMC / P-CODE
TEST MENU
LCD / KEY / LED / BUZ
SDRAM / SMC / P-CODE
TFT / TV STROBE AF / MS FOCUS COLOR TEST BURN IN
This menu w ill be showed these functions operating state Select this m enu by pressing the Up(▲)/Down(▼) buttons.
1. LCD : TN LCD displayed state
2. KEY :
3. LED : LED lighting state
4. BUZ : Beep sound state Pressed the enter button after selected, it will be showed you these functions automatically. And then turn off the power, it will be canceled.
This menu w ill be showed these menu values Select this menu by pressing the Up(▲)/Down(▼) buttons.
1. SDRAM : SDRAM check
2. SMC : SMC check
3. P-CODE : please check this no, after firmware
upgraded.
4. VERSION : Firmware version. Pressed the enter button after selected, it will be
SDRAM OK SMC OK SMC WP OFF P-CODE 09061 VERSION S30-12
showed you these functions automatically. And then press the enter button, it will be canceled.
Firmware : 30-12, P-CODE : 09061
Page 2
TFT / TV
TEST MENU
LCD / KEY / LED / BUZ SDRAM / SMC / P-CODE
TFT / TV
STROBE
TEST MENU
LCD / KEY / LED / BUZ SDRAM / SMC / P-CODE TFT / TV
AF / MS FOCUS COLOR TEST BURN IN
This menu w ill be showed the TFT LCD and TV out functions. Select this menu by pressing the Up(▲)/Down(▼) buttons.
1. TFT : Press the Up(▲) button, it will be displayed
the preview.
2. TV : Press the LCD button, it will be changed the
NTSC /PAL mode.
Press the enter button, it w ill be canceled.
This menu w ill be showed the STROBO functions. Select this menu by pressing the Up(▲)/Down(▼) buttons. And press the enter button and then press the shutter button, it will be flashed the strobo 3 times automatically.
AF / MS
TEST MENU
LCD / KEY / LED / BUZ SDRAM / SMC / P-CODE TFT / TV STROBE
AF / MS
FOCUS COLOR TEST BURN IN
This menu w ill be showed the lens unit operating. Select this menu by pressing the Up(▲)/Down(▼) buttons. And press the enter button, it w ill be operating the shutter and lens automatically.
Page 3
FOCUS
TEST MENU
LCD / KEY / LED / BUZ SDRAM / SMC / P-CODE TFT / TV STROBE AF / MS
FOCUS
COLOR TEST BURN IN
To adjust focus, Select this menu by pressing the Up(▲)/Down(▼) buttons. And set the camera as belows figure and the press the enter button, it w ill be adjusted the focus automatically. When you replace the main board or lens unit w ith new one you have to adjust the focus.
AF Chart
A : 58cm
1.86m
B : 76cm
a b
Camera
a : 1cm b : 1cm
COLOR TEST
TEST MENU
LCD / KEY / LED / BUZ SDRAM / SMC / P-CODE TFT / TV STROBE AF / MS FOCUS
COLOR TEST
BURN IN
To adjust TFT LCD color, Select this menu by pressing the Up(▲)/Down(▼) buttons. And set the camera as belows figure and the press the enter button, it w ill be adjusted the focus automatically. When you replace the main board or lens unit w ith new one you have to adjust the focus.
Page 4
Mode dial ;
- Set up mode : Green color
- Video clip mode : Red color
- Play mode : Blue color
- Capture mode : Gray bar
How to adjust TFT LCD color
1. Select this mode and press enter button, you can see as below numberal.
2. Adjust each color value as beows method. TESTING
Press the LCD button adjustment the contrast.
0 0 0 8 1 3 2 1 2 8 1 2 0
Press the Left key Changing to yellow color Press the Right key Changing to blue color
Press the UP key Changing to red color
Press the Down key Press the Flash/Macro buttons adjustment the
Changing to Green
color brightness
3. If you completed the adjustment, press the enter button and displayed the OK message on the LCD and then turn off the power.
BURN IN
TEST MENU
LCD / KEY / LED / BUZ SDRAM / SMC / P-CODE TFT / TV STROBE AF / MS FOCUS COLOR TEST
BURN IN
Select this menu by pressing the Up(▲)/Down(▼) buttons. And press the enter button, it w ill be check the all function by itself.
Loading...