Samsung CZ-21Q1MA, CZ-21S8ML, CS-21T4MA, CS-21T3MA User Manual
COLOUR
TELEVISION
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ENG
REMOTE CONTROL
ON-SCREEN MENUS
ENJOY GAME
ENG
!
!
Safety Instructions
The following illustrations represent the precautions to be taken when using and moving your television.
10%
H
5°
Do NOT expose the television to
extreme temperature conditions
(below 5°C and above 35°C) or to
extreme humidity conditions (less
than 10% and more than 75%).
If the television is broken, do not
try to repair it yourself. Contact
qualified service personnel.
75%
35°
H
THIS DEVICE IS NOT FOR USE IN INDUSTRIAL ENVIRONMENTS
Do NOT expose the television to
direct sunlight.
During a storm conditions
(especially when there is lightning)
unplug the television from the
mains socket and aerial.
Do NOT expose the television to
any liquids.
If the remote control is not used for
a long period of time, remove the
batteries and store it in a cool, dry
place.
Please use a soft and dry cloth (not containing volatile matter) when you clean the TV.
➢
Caution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO PREVENT ELECTRICAL SHOCK, DO
NOT REMOVE REAR COVER, NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING: TO PREVENT DAMAGE WHICH MAY
RESULT IN FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
The main voltage is indicated on the rear of
☛
the TV set and the frequency is 50 or 60Hz.
The lightning flash and arrow head
within the triangle is a warning sign
alerting you of “dangerous voltage”
inside the product.
The exclamation point within the
triangle is a warning sign alerting
you of important instructions
accompanying the product.
Mode System
CS PAL-B/G, D/K, I, SECAM-B/G,D/K, I,
NTSC4.43 (NTSC3.58; option)
CB PAL-B/G
CZ PAL-B/G, D/K, I, SECAM-B/G,D/K, I,
NTSC4.43
2
3
ENG
Contents
◆ PREPARING YOUR TELEVISION
■
Safety Instructions......................................................................................... 2
■
Caution.......................................................................................................... 2
■
Front Panel Controls...................................................................................... 4
■
Using the Buttons on the Front Panel............................................................ 4
■
Connection Panels ........................................................................................ 5
■
Infrared Remote Control................................................................................ 6
■
Inserting the Batteries in the Remote Control................................................ 8
■
Connecting the Aerial (or Cable Television Network).................................... 8
■
Switching Your Television On and Off........................................................... 9
■
Placing Your Television in Standby mode..................................................... 9
■
Plug & Play Feature....................................................................................... 11
■
Choosing Your Language.............................................................................. 12
◆ SETTING UP THE CHANNELS
■
Storing the Channels Automatically............................................................... 13
■
Storing the Channels Manually...................................................................... 14
■
Skipping Unwanted Channels ....................................................................... 15
■
Fine tuning Channel Reception ..................................................................... 16
■
Sorting the Stored Channels ......................................................................... 17
◆ USING THE TELEVISION
■
Changing the Picture Standard ..................................................................... 18
■
Selecting the Picture Format......................................................................... 18
■
Adjusting the Picture Settings ....................................................................... 19
■
Changing the Sound Standard...................................................................... 20
■
Adjusting the Volume..................................................................................... 21
■
Extra Sound Settings
(Auto Volume / Melody / Pseudo Stereo / Turbo Sound ............... ..................................... 22
■
Selecting the Sound Mode ............................................................................ 24
■
Switching the Sound Off Temporarily............................................................ 24
■
Setting the Sleep Timer................................................................................. 25
■
Setting and Displaying the Current Time....................................................... 25
■
Switching the Television On and Off Automatically....................................... 26
■
Setting the Blue Screen Mode....................................................................... 27
■
Activating the Child Lock ............................................................................... 28
■
Enjoying Games ............................................................................................ 31
◆ INFORMATION ON CONNECTIONS AND RECOMMENDATIONS FOR USE
■
Connecting to the Audio/Video Input/Outputs ............................................... 32
■
Viewing Picture From External Sources........................................................ 34
■
Automatic Degaussing to Remove Color Patches......................................... 34
■
Troubleshooting: Before Contacting Service Personnel................................ 35
☛
➢
Symbols
Press Important Note
■
Adjusting the Woofer Settings ...................................................................... 23
■
Selecting for Pick'n' Choose .......................................................................... 27
■
Setting the Reminder..................................................................................... 29
■
A ctivating / Deactivating Digital Noise Reduction feature ............................. 20
■
Storing the Channels Automatically (Turbo Store) ........................................ 13
■
Becoming Familiar with Remote Control ...................................................... 10
■
Equalizer Settings ......................................................................................... 23
■
Connecting to the DVD Input ........................................................................ 33
■
Channel Scan ............................................................................................... 19
4
ENG
Front Panel Controls (depending on the model)
➣
Buttons and markings are subject to change.
MENU DISPLAY
VOLUME ADJUSTMENT
CHANNEL SELECTION
POWER
STAND-BY INDICATOR
REMOTE CONTROL SENSOR
Using the Buttons on the Front Panel
If your remote control no longer works or you have lost it, you can
use the controls on the front panel of the television to:
◆ Switch on the television when it is in Standby mode and
select channels
( ▼ CH ▲ )
◆ Access the main menu ( MENU )
◆ Adjust the volume (
-
VOL + )
Buttons on the front panel have the same function as corresponding
buttons on the remote control.
MENU DISPLAY
VOLUME ADJUSTMENT
CHANNEL SELECTION
STAND-BY
INDICATOR
REMOTE CONTROL SENSOR
5
ENG
Connection Panels
➢
The actual configuration on your TV may be different, depending on
your model.
Rear of TV
➢
Connecting earphones ( ) /headphones ( )
◆ You can connect a set of earphones/headphones to your television if you wish to watch a
television programme without disturbing the other people in the room.
◆ Prolonged use of earphones/headphones at a high volume may damage your hearing.
INPUT
MONITOR
-OUT
VIDEO AUDIO
INPUT
MONITOR
-OUT
VIDEO
(
MONO
)
L-AUDIO-R
A
A
B
B
B
Front of TV
RCA AUDIO /VIDEO INPUT
CONNECTORS
Side of TV
RCA AUDIO/VIDEO
INPUT CONNECTORS
RCA AUDIO/VIDEO
INPUT CONNECTORS
HEADPHONE JACK (OPTION)
HEADPHONE JACK
(OPTION)
A)
RCA AUDIO/VIDEO INPUT/OUTPUT CONNECTORS
B) 75 COAXIAL CONNECTOR FOR AERIAL/CABLE NETWORK
ENG
Infrared Remote Control
(depending on model)
➢
The performance of the remote control may be affected by bright light.
TELEVISION STAND-BY
DIRECT CHANNEL SELECTION
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
MENU DISPLAY
MOVE TO THE REQUIRED MENU
OPTION/
ADJUST AN OPTION VALUE
RESPECTIVELY
GAME KEY
EXTERNAL INPUT SELECTION
EXIT FROM ANY DISPLAY
PREVIOUS CHANNEL
CHANGE CONFIRMATION
INFORMATION DISPLAY
AUTOMATIC SWITCH OFF
ONE/TWO/THREE-DIGIT
CHANNEL SELECTION
TUNER/CABLE NETWORK
SELECTION
SWITCH REPEATEDLY
BETWEEN THE LAST TWO
CHANNELS DISPLAYED
PICTURE SIZE
VOLUME DECREASE
NEXT CHANNEL
CHANNEL SCAN KEY
PICTURE MODEL SLECTION
Buttons and markings are subject to change.
➣
6
Infrared Remote Control
PICTURE MODEL SLECTION
SOUND MODE SELECTION
Buttons and markings are subject to change.
➣
TELEVISION STAND-BY
DIRECT CHANNEL SELECTION
(depending on model)
ENG
ONE/TWO/THREE-DIGIT
CHANNEL SELECTION
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
VOLUME DECREASE
TUNER/CABLE NETWORK
MOVE TO THE REQUIRED MENU
ADJUST AN OPTION VALUE
SOUND EFFECT SELECTION
SELECTION
MENU DISPLAY
OPTION/
RESPECTIVELY
GAME KEY
TURBO SOUND
CHANNEL SCAN KEY
SWITCH REPEATEDLY
BETWEEN THE LAST TWO
CHANNELS DISPLAYED
NEXT CHANNEL
EXTERNAL INPUT SELECTION
PREVIOUS CHANNEL
INFORMATION DISPLAY
EXIT FROM ANY DISPLAY
CHANGE CONFIRMATION
PICTURE SIZE
AUTOMATIC SWITCH OFF
The performance of the remote control may be affected by bright light.
➢
7
8
ENG
Inserting the Batteries in the Remote Control
You must insert or replace the batteries in the remote control when
you :
◆ Purchase the television.
◆ Find that the remote control is no longer operating
correctly.
1 Remove the cover of the remote control by pressing the symbol
( ) and pulling the cover in the direction of the arrow.
2 Insert batteries, taking care of the polarities:
◆ + on the battery with +on the remote control
◆
-
on the battery with -on the remote control
3 Replace the cover by pushing it in the direction of the arrow.
75Ω
Rear of TV
Connecting the Aerial (or Cable Television Network)
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
Plug the aerial or cable network input cable to the 75Ω coaxial socket
on the rear of the television.
Cable
Television
Network
Switching Your Television On and Off
The mains lead is attached to the rear of the television.
1 Plug the mains lead into an appropriate socket.
The main voltage is indicated on the rear of the TV set and
➢
the frequency is 50 or 60Hz.
2 Press the POWER (ON/OFF) button on the front of the
television.
: The Standby indicator lights up on the front panel.
Result
3 Press the POWER button on the remote control to switch the
television on.
: The programme that you were watching last is re-
Result
4 To switch your television off, press the POWER (ON/OFF)
button again on the front of the television.
selected automatically.
ENG
Placing Your Television in Standby mode
Your television can be placed in Standby mode, in order to reduce:
◆ Power consumption
◆ Wear of the cathode ray tube
The Standby mode can be useful when you wish to interrupt
viewing temporarily (during a meal, for example).
The television is placed automatically in Standby mode when you
turn it on.
1 Press the POWER button on the remote control.
Result:
2 To switch the screen back on, simply press the POWER button
again on the remote control.
Do not leave your television in standby mode for long
➣
periods of time (when you are away on holiday, for example).
In this case, you should switch it off completely.
The screen is turned off and the Standby indicator on
the front of the television lights up.
9
Becoming Familiar with the Remote Control
ENG
The remote control is used mainly to:
Change channels and adjust the volume
◆
◆
Set up the television using the on-screen menu system
The following table presents the most frequently used buttons and
their functions.
Button Viewing Function Menu Function
Used to display the next
stored channel.
Used to display the previous
stored channel.
to Used to display the corresponding channels.
-/--/---
PRE-CH
Used to select a channel numbered ten or over.
Press this button, and the "
Enter the two or three digit channel number.
Press the PRE-CH button. The TV will switch to the last
channel viewed.
To quickly switch between two channels that are far apart,
tune to one channel, then use the number button to select
second channel. Then, use the PRE-CH button to quickly
alternate between them.
--
" "---
-
-
" symbol is displayed.
MUTE
MENU
EXIT
TV
Used to increase the
volume.
Used to decrease the
volume.
Used to switch the sound off temporarily.
To turn the sound back on, press this button again, or
➣
press the
Used to display the Used to return to the previous
on-screen menu system. menu or normal viewing.
-
-
-
Used to switch the Used to exit from the menu
television on when it is system and return to normal
in Standby mode. viewing directly
-or+
-
-
button.
Used to:
◆ Display a submenu
containing selections for
the current menu option
◆ Increase/decrease a
menu option value
Used to confirm your choice.
Used to exit from the menu
system and return to normal
viewing directly.
10
Plug & Play Feature
ENJOY YOUR WATCHING
Time
Clock - - : - - am
When the television is initially powered ON, three basic customer
settings proceed automatically and subsequently: setting the
language, channel and clock.
1 If the television is in Standby mode, press the POWER button
on the remote control.
ENG
Result:
The message “Plug & Play” is displayed. It flickers for a
little while and then the “Language” menu is automatically
displayed.
2 Press the ▲ or ▼ button to select required language. Press the
MENU button to enter the language, and then the message “Ant.
Input Check” is displayed.
If any language is not selected on the “Language” menu, the
➣
“Language” menu will be displayed about 30 seconds later.
3 Make sure that the antenna is connected to the TV. And then press
the or button to store the channels (refer to “Storing the
¦
Channels Automatically” on page 12).
Result: The horizontal bar is displayed, and then channels are
stored in an order which reflects their positions in the
frequency range.
4 When searching and storing is complete, the “Time” menu is
displayed.
¦
5 Press the or button to move to the hour or minute. Set the hour
or minute by pressing the ▲ or ▼ button (refer to “Setting and
Displaying the Current Time” on page 26).
6 When you have finished, press the MENU button.
Result:
7 If you want to reset this feature...
1 Press the MENU button.
2 Press the ▲ or ▼ button to select the “Function”, and then
The message “ENJOY YOUR WATCHING” is displayed,
and then the channel which has been stored will be
activated.
press the or button.
¦
Plug & Play
Ant. Input Check
WXAuto Store Exit
P 1
471 MHz 48 %
Exit
Time
Clock 11 : 35
WXMove Exit
Enjoy Your Watching...
3 Select the “Plug & Play” by pressing the ▲ or ▼ button, and
then press the
Result:
or button.
¦
The message “Plug & Play” is displayed.
Function
Language : English
Time
Plug & Play
Blue Screen : Off
Child Lock
Select WXEnter Exit
11
Loading...