Samsung CW-21Z573B User Manual
DIGITAL
TELEVISION
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
TELETEXT (Option)
Register your product at www.samsung.com/global/register
Record your Model and Serial number here for future reference.
▪ Model _______________ ▪ Serial No. _______________
Important Warranty Information Regarding Television
Format Viewing
Standard screen format televisions (4:3, the aspect ratio of the screen width to height) are primarily
designed to view standard format full-motion video. The images displayed on them should primarily be in
the standard 4:3 ratio format and constantly moving.Displaying stationary graphics and images on screen,
such as the dark top and bottom letterbox bars (wide screen pictures), should be limited to no more than
15% of the total television viewing per week.
Wide screen format televisions (16:9, the aspect ratio of the screen width to height) are primarily designed
to view wide screen format full-motion video. The images displayed on them should primarily be in
the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature, and
constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on
non-expanded standard format television video and programming, should be limited to no more than 15%
of the total television viewing per week.
Additionally, viewing other stationary images and text such as stock market reports, video game displays,
station logos, web sites or computer graphics and patterns, should be limited as described above for all
televisions. Displaying any stationary images that exceed the above guidelines can cause uneven aging
of picture tubes (CRTs) that leave subtle, but permanent burned-in ghost images in the television picture.
To avoid this, vary the programming and images, and primarily display full screen moving images, not
stationary patterns or dark bars. On television models that offer picture sizing features, use these controls
to view the different formats as a full screen picture.
Be careful in the selection and duration of television formats used for viewing. Uneven CRT aging as a
result of format selection and use, as well as other burned-in images, is not covered by your Samsung
limited warranty.
Any functions related to Digital TV (DVB) will only work in countries or areas where DVB-T (MPEG2)
digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive
DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with
the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not be
available in some countries.
© 2007 Samsung Electronics Co., Ltd. All rights reserved.
English - 2
Contents
General Information
Important Warranty Information Regarding
Television Format Viewing .............................. 2
Checking Parts ................................................4
Control Panel ................................................. 4
Connection Panel ............................................5
Viewing the Remote Control .......................... 7
Operation
Switching Your Television On and Off ............. 9
Viewing the Menus ..........................................9
Plug & Play Feature ...................................... 10
Viewing External Signal Sources .................. 12
Editing Device Names ...................................13
Channel Control
Storing Channels Automatically .................... 13
Storing Channels Manually ........................... 14
Adding Channels ...........................................15
Sorting the Stored Channels ......................... 16
Assigning Names to Channels ...................... 16
Picture Control
Changing the Picture Standard ..................... 17
Customizing the Picture Settings .................. 17
Selecting the Picture Size ............................. 18
Digital NR
.......................................................18
Function Description
Time Features ............................................... 21
Child Lock ..................................................... 22
Language / Blue Screen / Melody ................. 23
Using the DTV Feature
Previewing the DTV Menu System ............... 24
Displaying Programme Information ...............25
Operating the DTV Menu .............................. 26
Appendix
Teletext Feature (depending on the model) .. 36
Troubleshooting ............................................ 37
Sound Control
Sound Features ............................................19
Selecting the Sound Mode (depending on
the model) ..................................................... 20
Symbols
Press
English - 3
☛ ➢
Important
Note
Checking Parts
Owner’s Instructions Remote Control/
AAA Batteries
Warranty Card/Registration
Safety Guide Manual
Control Panel
Front Panel
The product colour and shape may vary depending on the model.
➢
1
MENU
Press to see the on-screen menu of your TV’s
features.
Press the MENU button in DTV mode to
➢
display the DTV menu.
The analog menu appears when you
press the MENU button again.
To dismiss the menu, press the MENU
button once again.
2 −
3
+
Press to increase or decrease the volume.
In the on-screen menu, use the −+
buttons as you use the ◄ and ► buttons on
the remote control and also use decrease and
increase buttons as the functions of return and
enter respectively.
C/P.
Press to change channels. In the on-screen
menu, use the C/P. buttons as
you use the ▲ and ▼ buttons on the remote
control.
English - 4
4
Remote Control Sensor
Aim the remote control towards this spot on
the TV.
5
Power Indicator
Blinks and turns off when the power is on and
lights up in stand-by mode.
6
(Power) button
Press to turn the TV on and off.
If the TV was turned off by using the POWER
button on the front panel, you will not be able
to turn on the TV by using a remote control.
Card/
Cloth-Clean
Connection Panel
Side Panel
1
The product colour and shape may vary depending on the model.
➢
2
1
EXT 2(AV IN)
Video and audio inputs for external devices,
such as a camcorder or VCR.
Headphones jack
You can connect a set of headphones if you
wish to watch a television programme without
disturbing the other people in the room.
Prolonged use of headphones at a high
➢
volume may damage your hearing.
2
English - 5
Rear Panel
3
2
1
The product colour and shape may vary depending on the model.
➢
Whenever you connect an audio or video system to your set, ensure that all elements are
☛
switched off.
When connecting an external device, match the colour of the connection terminal to the cable.
1
EXT 1, EXT 2
Inputs or outputs for external devices, such as
VCR, DVD, video game device or video disc
players.
Input/Output Specification
Connector
EXT 1
EXT 2
2
SERVICE
− Connector for service.
− Connect the serial jack between the
electro-motion wall mount bracket and your
TV when you want to adjust the TV viewing
angle using your remote control.
Input Output
Video Audio(L/R) RGB Video + Audio(L/R)
✔ ✔ ✔
✔ ✔
Only TV or DTV
output is available.
AV output is available.
English - 6
3
COMMON INTERFACE Slot
Insert CI (Common Interface) card into the slot.
(refer to page 35)
− When not inserting “CI CARD” in some
channels, “Scramble Signal” is displayed on
the screen.
− The pairing information containing a
telephone number, CI CARD ID, Host ID,
and other information will be displayed in
about 2~3 minutes. If an error message
is displayed, please contact your service
provider.
− When the channel information configuration
has finished, the message “Updating
Completed” is displayed, indicating that the
channel list is now updated.
Insert the CI-Card in the direction marked
➢
on it.
4
Connecting to an Aerial or Cable Television
Network
Connect the aerial or network input cable to
the 75 Ω coaxial socket.
To view television channels correctly, a signal
must be received by the set from one of the
sources: an outdoor aerial, cable television
network, or satellite network. If you are using
an indoor aerial, you may need to adjust it
when tuning your television until you obtain a
picture that is both sharp and clear.
4
or
Cable Television
Network
Viewing the Remote Control
This is a special remote control for the visually impaired persons, and has Braille points on the
➢
Power, Channel, and Volume buttons.
The performance of the remote control may be affected by bright light.
1
POWER button
(turns the TV on and off)
2
Number buttons for direct
channel access
3
One/Two-digit channel
selection
4
Channel control button
(Refer to page 15)
(Only in DTV signal)
5
Selects the TV and DTV
mode directly
6
Temporary sound switch-off
7
Volume increase
Volume decrease
8
Displays the main on-screen
menu
9
Returns to the previous
menu
!
Picture effect selection
(Refer to page 17)
@
Sound effect selection
#
Sound mode selection
$
Digital subtitle display
%
Available source selection
^
Previous channel
&
DTV menu display
*
Electronic Program Guide
(EPG) display
(
Next channel
Previous channel
)
Exit the on-screen menu
a
Control the cursor in the
menu
b
Use to see information on
the current broadcast
d
Picture size selection
e
Automatic Power-off
f
Digital NR on/off
g
Turbo sound
Teletext Functions
(Refer to page 36)
5
Exit from the teletext display
(depending on the model)
8
Teletext index
0
Fastext topic selection
@
Teletext store
%
Teletext mode selection
(LIST/FLOF)
^
Teletext sub page
(
P :Teletext next page
P :Teletext previous page
)
Teletext cancel
b
Teletext reveal
c
Teletext display/mix both
teletext information and the
normal broadcast
d
Teletext hold
e
Teletext size
English - 7
Continued...
Installing Batteries in the Remote Control
1 Lift the cover at the back of the remote control upward as
shown in the figure.
2 Install two AAA size batteries.
Make sure to match the “+” and “–” ends of the
➢
batteries with the diagram inside the compartment.
Do not mix battery types, i.e. alkaline and manganese.
3 Close the cover as shown in the figure.
Remove the batteries and store them in a cool and dry
➢
place if you won’t be using the remote control for a long
time. The remote control can be used up to about 23 feet
from the TV. (Assuming typical TV usage, the batteries last
for about one year.)
If the remote control doesn’t work! Check the following:
➢
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
English - 8
Switching Your Television On and Off
The main lead is attached to the rear of the television.
1 Plug the main lead into an appropriate socket.
The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
➢
2 Press the I (Power) button (On/Off) on the front of the television or press the POWER button on the
remote control to switch the television on. The programme that you were watching last is reselected
automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing
Channels Automatically” on page 13 or “Storing Channels Manually” on page 14.
If the television is initially powered on, several basic customer settings proceed automatically.
➢
Refer to “Plug & Play Feature” on page 10.
3 To switch the television off, press the I (Power) button (On/Off) on the front of the television or press
the POWER button on the remote control.
4 To switch the TV on, press the I (Power) button (On/Off) on the front of the TV or press the POWER
button or number buttons on the remote control.
Viewing the Menus
1 Press the MENU button.
The main menu is displayed on the screen.
Its left side has five icons: Picture, Sound, Channel, Setup,
and Input.
2 Press the ▲ or ▼ button to select one of the icons.
Press the ENTER button to access the icon’s sub-menu.
3 Press the ▲ or ▼ button to move to items in the menu.
Press the ENTER button to enter items in the menu.
4 Press the ▲/▼/◄/► button to change the selected items.
Press the RETURN button to return to the previous menu.
5 Press the EXIT button to exit from the menu.
Picture
Mode : Dynamic ►
Contrast : 100
Brightness : 45
Sharpness : 75
Colour : 55
More
Move
Enter
Exit
English - 9
Plug & Play Feature
When the television is initially powered on, several basic customer settings proceed automatically
and subsequently.
The following settings are available.
If you accidentally select the wrong country for your TV, the
☛
characters on the screen may be wrongly displayed.
Any functions related to Digital TV (DVB) will only work in
☛
countries or areas where DVB-T (MPEG2) digital terrestrial
signals are broadcasted. Please confirm with your local
dealer if you can receive DVB-T signals. Although this TV set
follows the DVB-T specification, maintaining compatibility with
the future coming DVB-T digital terrestrial broadcasts is not
guaranteed. Several functions may not be available in some
countries.
1 If the television is in standby mode, press the POWER button
on the remote control. The message Start Plug & Play is
displayed. Press the ENTER button.
2 The Language menu will automatically appear after several
seconds.
3 Select the appropriate language by pressing the ▲ or ▼
button.
Press the ENTER button. The message Select Home Mode
when installing this TV at home. is displayed.
4 Press the ◄ or ► button to select SHOP or HOME, then press
the ENTER button. The message to check the connected
status of the antenna is displayed.
The default selection is HOME.
➢
We recommend setting the TV to Home mode for the best
➢
picture in your home environment.
Shop mode is only intended for use in retail environments.
➢
If the unit is accidentally set to Shop mode, and you want to
➢
return to Dynamic (Home) mode, press the Volume button
and then hold down the MENU button for five seconds on
the TV panel.
5 Make sure that the antenna is connected to the TV.
Press the ENTER button. The Country menu is displayed.
6 Select your country or area by pressing the ▲ or ▼ button.
Press the ENTER button.
The message Some DTV functions may not be available.
Digitally Scan? is displayed.
This OSD is concerned for all countries except for the
➢
following countries: France, Germany, Italy, Netherlands,
Spain, Switzerland, United Kingdom, Austria, Sweden,
Finland, Denmark
If your country supports the DTV functions, the message is
not displayed. Then you can follow the instructions from step
12. When the local service provider does not support DTV
broadcasting but you choose a DTV supporting country, it
enters the DTV Plug & Play but DTV functions may not work
properly. When No is selected, follow the instructions from step
7 to 10. When Yes is selected, follow the instructions from step
11.
Select Home Mode
when installing this TV at home
Some DTV functions may not be
available. Digital Scan?
Plug & Play
Start Plug & Play
OK
Enter
Plug & Play
Language
English
Deutsch
Français
Nederlands
Español
Italiano
Português
Ελληνικά
Čeština
Srpski
Hrvatski
Move
SHOP
Move
Check antenna input.
Country Belgium
France
Germany
Italy
Netherlands
Spain
Switzerland
United Kingdom
Austria
Eastern Europe
▼ More
Move
Yes
Move Enter
Enter
Plug & Play
Enter
Plug & Play
OK
Enter
Plug & Play
Enter
Plug & Play
Română
Magyar
Polski
Русский
Български
Türkçe
Svenska
Norsk
Dansk
Suomi
HOME
No
Exit
Skip
Skip
Skip
Skip
Skip
English - 10
Continued...
7 Select No by pressing the ◄ or ► button, then press the
ENTER button. Auto Store menu is displayed.
8 Press the ENTER button to start search the channels. The
channel search will start and end automatically. After all the
available channels are stored, Clock Set menu is automatically
displayed. Press the ENTER button.
To stop the search before it has finished, press the
➢
ENTER button with Stop selected.
9 Press the ◄ or ► button to select Hour or Minute. Set these by
pressing the ▲ or ▼ button.
10 Press the ENTER button to confirm your setting. The message
Enjoy your viewing is displayed. When you have finished,
press the ENTER button.
Even if the ENTER button is not pressed, the message will
➢
automatically disappear after several seconds.
11 Select Yes
by pressing the ◄ or ► button, then press the
ENTER button. Auto Store menu is displayed.
12 Press the ENTER button to start search the analog channels.
The analog channel search will start and end automatically.
After all the available analog channels are stored, the screen
for searching digital channels is automatically displayed.
To stop the search before it has finished, press the
➢
ENTER button with Stop selected.
13 Press the ENTER button to start search the digital channels.
The digital channel search will start and end automatically.
After all the available digital channels are stored, the screen to
select a time zone is displayed depending on the country.
To stop the search before it has finished, press the
➢
ENTER button with Stop selected.
If the DTV channel is updated, the Source in the source
➢
list of the Input menu is automatically changed to DTV.
For detailed descriptions about DTV channel update, refer
➢
to page 26 of this manual.
14 Press the ▲ or ▼ button to select required time zone, then
press the ENTER button. The screen for setting the time is
displayed. Press the ENTER button.
15 You can set the Month, Day, Year, Hour, or Min directly by
pressing the numeric buttons on the remote control.
You can set the Hour or Minute directly by pressing the
➢
numeric buttons on the remote control.
16 Press the ENTER button to confirm your setting. The message
Enjoy your watching. is displayed. When you have finished,
press the ENTER button.
Even if the ENTER button is not pressed, the message will
➢
automatically disappear after several seconds.
Auto Store
P 4 C6 --- -- 40 MHz
0 %
Auto Store
P4 C9 -- -- - 51 MHz
3 %
Plug & Play
Start
Enter
Plug & Play
Enter
Plug & Play
Clock Set 08 : 05
Sleep Timer : Off
On Timer
Off Timer
On Timer Volume : 10
Move
Plug & Play
0%
Services found: 0 Channel:
Skip
Plug & Play
Scanning for digital services...
29%
Services found: 6 Channel: 35
Skip
Set the current time.
Adjust
Plug & Play
Month Day Year
01 01
Hour
00
Move
Stop
Enter
Start
Stop
Min
00
--
--
2007
Select
Skip
Skip
: -- Off
: -- Off
Skip
-
Skip
English - 11
Enjoy your watching.
OK
If you want to reset this feature …
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
3 Press the ENTER button again to select Plug & Play.
The message Start Plug & Play is displayed.
Plug & Play
Language : English
Time
Child Lock
Blue Screen : On
Melody : On
Setup
►
►
►
►
►
►
Viewing External Signal Sources
You can switch between viewing signals from connected
equipment, such as a VCR, DVD, Set-Top Box, and the TV
source (broadcast or cable).
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Input, then press the
ENTER button.
3 Press the ENTER button again to select Source List.
4 Press the ▲ or ▼ button to select the signal source, then
press the ENTER button.
Available signal sources:
rear panel or EXT 2(AV IN) on the side panel), DTV
You can select these options simply by pressing the SOURCE
➢
button on the remote control.
TV, Ext.1, Ext.2 (EXT2 (AV) on the
Move
Move
Move
Enter
Source List : TV ►
Edit Name
TV
Ext.1
Ext.2
DTV
Enter
Source List
----- -
----- -
Enter
Return
Input
►
Return
Return
To watch television programme again, press the TV/DTV
➢
button and select the channel number required.
English - 12
Editing Device Names
You can give a name to the external source.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Input, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Edit Name, then press the
ENTER button.
4 Press the ▲ or ▼ button to select the external source to be
edited, then press the ENTER button.
5 Select the required device by pressing ▲ or ▼, then press the
ENTER button.
Available device names:
VCR, DVD, Cable STB, Sat. STB, AV
Receiver, DVD Receiver, Game, Camcorder, DVD Combo
6 Press the EXIT button to exit.
Storing Channels Automatically
Not available in DTV or external input mode.
➢
You can scan for the frequency ranges available to you
(availability depends on your country).
Automatically allocated programme numbers may not
correspond to actual or desired programme numbers. However
you can sort numbers manually and clear any channels you do
not wish to watch.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ENTER button again. The available countries are
listed.
4 Select your country by pressing the ▲ or ▼ button, then press
the ENTER button.
Even though you have changed the country setting in this
➢
menu, the country setting for DTV is not changed. Use the
Plug & Play function to change the country setting for DTV.
(Refer to Pages 10 to 11)
5 Press the ▲ or ▼ button to select Auto Store, then press the
ENTER button.
6 Press the ENTER button again to start the search.
The search will end automatically.
To stop the search before it has finished, press the MENU
➢
or the ENTER button.
7 When searching and storing are completed, the Sort menu is
displayed.
To sort the stored channels into the desired numerical order,
➢
go to step 4 of the “Sorting the Stored Channels” procedure on
page 16.
To exit from the channel store function without sorting the
➢
channels, press the MENU button repeatedly until the menus
disappear.
P 4 C6 --- -- 40 MHz
0 %
Source List : TV ►
Edit Name
Move
Move
Move
Move
Enter
Ext.1
Ext.2
Country :
Auto Store
Manual Store
Add/Delete
Sort
Name
Country : United Kingdom ►
Auto Store ►
Manual Store ►
Add/Delete ►
Sort ►
Name ►
From : P 3
To : P
Store : ?
:
:
Enter
Belgium
France
Germany
Italy
Netherlands
Spain
Switzerland
United Kingdom
Austria
Eastern Europe
Sweden
Finland
Denmark
Enter
Enter
Search
Start
Enter
Edit Name
----- -
----- -
VCR
----- -
DVD
Cable STB
Sat. STB
AV Receiver
DVD Receiver
Game
Camcorder
DVD Combo
Channel
Channel
Return
--
Input
►
Return
Return
Return
Return
Sort
English - 13
Move
Adjust
Return
Storing Channels Manually
Not available in DTV or external input mode.
➢
You can store television channels, including those received
via cable networks.
When storing channels manually, you can choose:
Whether or not to store each of the channels found.
The programme number of each stored channel which you
wish to identify.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
Country : United Kingdom ►
Auto Store ►
Manual Store ►
Add/Delete ►
Sort ►
Name ►
Move
3 Press the ▲ or ▼ button to select Manual Store, then press
the ENTER button.
4 Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
5 When you are satisfied with your setting, press the ENTER
button.
6 Press the EXIT button to exit.
Prog. (Programme number to be assigned to a channel)
− Press the ◄ or ► button until you find the correct number.
You can also select the channel number directly by
➢
pressing the numeric buttons (0~9).
Prog. : P 2
Colour System : Auto ►
Sound System : BG ►
Search : 89MHz
Channel : C--
Store : ?
Move
Colour System: Auto/PAL/SECAM/NTSC4.43
− Press the ▲ or ▼ button to select the required colour standard.
Sound System: BG/DK/I/L
− Press the ▲ or ▼ button to select the required sound standard.
Search (When you do not know the channel numbers)
− Press the
ENTER button to start the search.
− The tuner scans the frequency range until the first channel or the channel that you selected is
received on the screen.
Channel (When you know the number of the channel to be stored)
− Press the ▲ or ▼ button to select
C (Air channel) or S (Cable channel).
− Press the ► button, then press the ▲ or ▼ button to select the required number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
➢
If there is abnormal sound or no sound, reselect the sound standard required.
➢
Store (When you store the channel and associated programme number)
− Set to
OK by pressing the ENTER button.
Channel mode
☛
P (Programme mode): When completing tuning, the broadcasting stations in your area have
been assigned to position numbers from P00 to P99. You can select a channel by entering the
position number in this mode.
C (Air channel mode): You can select a channel by entering the assigned number to each air
broadcasting station in this mode.
S (Cable channel mode): You can select a channel by entering the assigned number for each
cable channel in this mode.
Enter
Manual Store
Adjust
Channel
Return
Return
English - 14
Adding Channels
Not available in DTV or external input mode.
➢
Using the Add/Delete, you can conveniently add or delete
channels.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Add/Delete, then press the
ENTER button.
4 Press the ▲ or ▼ button to select the channel to add or erase.
If necessary, select Added or Deleted by pressing the ENTER
button.
5 Repeat Step 4 for each channel to be added or erased.
You can select these options simply by pressing the CH LIST
➢
button on the remote control. (Only in DTV signal)
Channel
Country : United Kingdom ►
Auto Store ►
Manual Store ►
Add/Delete ►
Sort ►
Name ►
Move
Move
Enter
▲ More
P 2 : Deleted
P 3 : Added
P 4 : Added
P 5 : Added
P 6 : Added
▼ More
Enter
Add/Delete
Return
Return
English - 15
English - 16
Sorting the Stored Channels
Not available in DTV or external input mode.
➢
This operation allows you to change the programme numbers
of the stored channels.
This operation may be necessary after using the auto store.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Sort, then press the ENTER
button.
4 Select the channel number that you wish to change by
pressing the ◄ or ► button repeatedly.
5 Press the ▲ or ▼ button to select To. Select the new channel
number which you wish to identify by pressing the ◄ or ►
button repeatedly.
6 Press the ▲ or ▼ button to select Store. Select OK to confirm
the exchange of channel numbers by pressing the ENTER
button. The selected channel is exchanged with the one
previously stored to the chosen number.
7 For all the channels to move to the required channel numbers,
repeat steps 4 to 6 after selecting the From by pressing the
▲ or ▼ button.
8 Press the EXIT button to exit.
Channel
Country : United Kingdom ►
Auto Store ►
Manual Store ►
Add/Delete ►
Sort ►
Name ►
Move
Move
Enter
From : P 3
To : P
Store : ?
From : P 3
To : P
Store : OK
Adjust
--
--
Return
Sort
Return
Sort
Assigning Names to Channels
Not available in DTV or external input mode.
➢
Channel names will be assigned automatically when channel
information is broadcast. These names can be changed,
allowing you to assign new names.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Name, then press the
ENTER button.
4 Press the ▲ or ▼ button to select the channel to be assigned
to a new name, then press the ENTER button.
5 Press the ▲ or ▼ button to select a letter, a number, or a
symbol (Results in this sequence: A~Z, 0~9, +, -, *, /, blank).
Move on to the previous or next letter by pressing the ◄ or ►
button.
6 Repeat steps 4 to 5 for each channel to be assigned to a new
name.
7 Press the EXIT button to exit.
Move
Move
Move
Enter
Country : United Kingdom ►
Auto Store ►
Manual Store ►
Add/Delete ►
Sort ►
Name ►
▲ More
P 3 :
P 4 :
P 5 :
P 6 :
▼ More
--- --
--- --
--- --
--- --
Enter
Enter
Channel
Return
Return
Name
Return
Loading...