How it Works
Samsung
Loading...
CS29Z58Z49

Samsung CS29Z45Z39, CS29Z47Z39, CS29Z50Z39, CS29Z50Z49, CS29Z58Z49 Owner's Instructions Manual

Owner’s Instructions
COLOR TELEVISION
CS29Z45Z39 CS29Z47Z39 CS29Z50Z39 CS29Z50Z49 CS29Z58Z49
AA68-03967C-00Eng_0506 5/7/08 6:29 PM Page 1
English - 2
➢
Connection Panel
(depending on the model)
☛
Please be sure to match the colour coded input terminals and cable jacks.
Connecting to the RCA
Input
The 3 (AUDIO-L/R) and 2 (VIDEO) connectors are used for equipment, such as a camcorder, video player, or video game device.
Connecting to the S-Video Input
The 1 (S-VIDEO input) and 2 (VIDEO input) connectors are used for equipment with an S-Video output, such as a camcorder or VCR.
➢
When both the front (or side) AV and rear connectors are connected to external equipment, the front (or side) AV receives priority.
Owner’s Instructions
Before operating, please read this manual thoroughly,
and retain it for future reference.
Register your product at
www.samsung.com/global/register
➢
Control Panel
(depending on the model)
◆ You can use the 3 buttons to switch the TV on when it is
in standby mode depending on the model.
◆ The 2 and 3 buttons also have the same function as the
œ/√/†/… buttons on the remote control.
◆ If the remote control no longer works or you have misplaced it, you can use the controls on the panel of the television.
Front (or Side) Panel
1 On-screen menu display 2 Volume adjustment 3 Channel selection 4 Remote control sensor 5 Indicator 6 Power on/off
cable television network
Rear Panel
or
COMPONENT IN
(480i/480p/576i/576p/
720p/1080i/1080p)
Y
P
B
P
R
L
R
I
I
AUDIO
cable television network
or
ΠS-Video input
´ Video input
ˇ Audio input
Front (or Side) Panel
☛
Whenever you connect an audio or video system to your television, ensure that all elements are switched off. Please be sure to match the colour coded input terminals and cable jacks.
Connecting to an Aerial or Cable Television Network
Connect the aerial or network input cable to the Œ (75 Ω coaxial socket). To view television channels correctly, a signal must be received by the set from one of the sources: an outdoor aerial, cable television network, or satellite network. If you are using an indoor aerial, you may need to adjust it when tuning your television until you obtain a picture that is both sharp and clear.
Connecting to the SCART Input/Output
The ´, 3 SCART connectors are used for equipment, such as a VCR, DVD, decoder, satellite receiver, video game device, or video disc player. The RCA4 connectors are used for equipment such as a DVD with component output.
continued...
COLOUR TELEVISION
AA68-03967C-00Eng_0506 5/7/08 6:29 PM Page 2
English - 3
The mains lead is attached to the rear of the television.
1 Plug the mains lead into an appropriate socket.
➢
The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
2 Press the “I” button (On/Off) on the front (or side) of the
television.
3 Press the POWER button on the remote control to
switch the television on. The programme that you were watching last is re-selected automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Channel - Auto Store” on page 3 or “Channel ­Manual Store” on page 4.
➢
If the television is initially powered on, several basic customer settings proceed automatically. Refer to “Setup - Plug & Play” on page 3.
4 To switch the television off, press the “I” button (On/Off)
on the front (or side) of the television.
Switching the Television On and Off
The television can be placed in standby mode, in order to reduce power consumption and wear of the cathode ray tube. Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).
1 Press the POWER button on the remote control while
viewing. The television is in standby mode.
2 To switch the television back on, simply press it again.
☛
Do not leave the television in standby mode for long periods of time (when you are away on holiday, for example). Turn the television off by pressing the “I” button (On/Off) on the front (or side) of the television. It is best to unplug the set from the mains and aerial.
Placing the Television in Standby Mode
11
POWER
Used to switch the TV on and off.
22
Numeric buttons
Used to select channels directly.
33
-/--
Used to select a channel numbered ten or over. Press this button, then “
--
” symbol is displayed. Enter the two-digit channel number.
44
/
Used to increase or decrease the volume.
55
MENU
Used to display the on­screen menu or return to the previous menu.
LNA
66 …… / †† / œœ / √√
Used to control the cursor in the menu.
77
S.MENU
Used to display the sound menu.
88
TURBO
Used to select the turbo sound option.
99
DUAL I-II
Used to select the sound mode.
00
SOURCE
Used to display all of the available video sources.
!!
INFO
Used to view the channel information and setting status you selected.
@@
PRE-CH
Used to switch repeatedly between the last two channels displayed.
##
CH /
Used to display the next or previous stored channel.
$$
EXIT
Used to exit from any display or return to normal viewing.
%%
MUTE
Used to switch the sound off temporarily. To turn the sound back on, press the MUTE, , or
button.
^^
ENTER
While using the on­screen menus, press the ENTER button to activate (or change) a particular item.
&&
S.MODE
Used to select the sound effect.
**
P.MODE
Used to select the picture effect.
((
TV
Used to return to the TV mode when it is in external input mode.
))
EZ.VIEW
Used to make TV viewing much easier.
Remote Control
(depending on the model)
➢
Operation of remote control may be affected by bright artificial light near to the TV.
MUTE
LNA
Installing Batteries
Remove the cover. Install two AAA size batteries, then replace the cover. When the remote control does not operate normally, check that the “+” and “-” ends of the batteries are inserted correctly or the batteries are drained.
➢
Do not mix battery types, i.e. alkaline and manganese.
AA68-03967C-00Eng_0506 5/7/08 6:29 PM Page 3
English - 4
◆ Source List
You can switch between viewing signal from connected equipment, such as a VCR, DVD, set-top box, and the TV source (broadcast or cable).
➢
You can change the required external source simply by pressing the SOURCE button on the remote control. It might take a short period of time for pictures to be switched. To return to the TV mode, press the TV button on the remote control.
Input
(depending on the model)
-
Source List
Move Enter Return
TV
EXT1 EXT2 S-Video
Source List
TV
3 Make sure that the antenna
is connected to the television (refer to page 1). Press the ENTER button. The Area menu is displayed.
4 Press the … or † button to
select your area. Press the
ENTER button.
5 To search the channels,
press the ENTER button. To stop the search, press the ENTER button. When the channel searching has finished, the Clock Set menu is displayed.
6 Press the œ or √ button to
move to the hour or minute. Set the hour or minute by pressing the … or † button.
7 When you have finished,
press the MENU button. The Enjoy your watching. is displayed, and then the channel which has been stored will be activated.
Re-setting the Plug & Play
Method: MENU ➜……/
††
(Setup) ➜ ENTER ➜……/
††
(Plug & Play) ➜ ENTER
Viewing the Menus
1 Press the MENU button.
The main menu is displayed on the screen. Its left side has five icons: Input, Picture, Sound, Channel, and Setup.
2 Press the … or † button to select one of the icons.
Press the ENTER button to access the icon’s sub-menu.
3 Press the … or † button to move to items in the menu.
Press the ENTER button to enter items in the menu.
4 Press the …/†/œ/√ button to change the selected
items. Press the MENU button to return to the previous menu.
5 Press the EXIT button to exit from the menu.
Setup - Plug & Play
When the television is initially powered on, several basic customer settings proceed automatically and subsequently. The following settings are available.
1 If the television is in standby
mode, press the POWER button on the remote control. The Start Plug & Play is displayed. To start Plug & Play, press the ENTER button. The Language menu is displayed.
➢
The Language menu will automatically appear after several seconds, even if the ENTER button is not pressed.
2 Select the appropriated language by pressing the … or
† button. Press the ENTER button.
The Check antenna input. is displayed.
➢
If any language is not selected, the language menu will disappear about 30 seconds later.
continued...
Plug & Play
Move Enter Skip
Country
Belgie
Deutschland España France Italia Nederland
Schweiz Sverige UK E. Europe Others
Plug & Play
Enter Skip
Stop
Auto Store
P 1 C-- 102MHz
7 %
Plug & Play
Enter Skip
Start
Auto Store
Plug & Play
Move Enter Adjust Skip
OK
Enjoy your watching.
Move Enter Return
Plug & Play
√√
Language : English
√√
Time
√√
Child Lock
√√
Blue Screen : On
√√
Melody : On
√√
Music Mode : Off
√√
Setup
TV
You can scan for the frequency ranges available to you (and availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However you can sort numbers manually and clear any channels you do not wish to watch.
Channels are sorted and stored in the order which reflects their position in the frequency range (with lowest first and highest last). The programme originally selected is then displayed.
➢
To stop the search before it has finished, press the ENTER button.
When finished, the Sort menu is displayed. To sort the stored channels into the desired numerical order, refer to “Channel - Sort”. To exit without sorting, press the EXIT button.
Channel - Auto Store
Move Enter Return
Country : Belgie
Search
Auto Store
TV
Search
Enter Return
Stop
P 1 C-- 102MHz
7 %
Belgie
Deutschland España France Italia Nederland Schweiz
††
Clock Set 00:00
Plug & Play
Move Enter Skip
Language
English
кЫТТНЛИ
Plug & Play
Enter Return
OK
Start Plug & Play.
Plug & Play
Enter Skip
OK
Check antenna input.
AA68-03967C-00Eng_0506 5/7/08 6:29 PM Page 4
Loading...
+ 8 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use