Samsung cs29z4hf9x service manual
COLOR TELEVISION RECEIVER
Chassis : KS4A(P)
Model : CS29Z4HF9X/BWT
CS34Z4HF9X/BWT
COLOR TELEVISION RECEIVER CONTENTS
Precautions
Reference Information
Specifications
Alignment and Adjustments
Exploded Views and Parts List
Electrical Parts List
Block Diagrams
Schematic Diagrams
1.
2.
3.
4.
5.
6.
7.
8.
1. Precautions
1-1 Safety Precautions
1. Be sure that all of the built-in protective
devices are replaced. Restore any missing
protective shields.
2. When reinstalling the chassis and its
assemblies, be sure to restore all protective
devices, including: nonmetallic control knobs
and compartment covers.
3. Make sure that there are no cabinet openings
through which people—particularly
children—might insert fingers and contact
dangerous voltages. Such openings include
the spacing between the picture tube and the
cabinet mask, excessively wide cabinet
ventilation slots, and improperly fitted back
covers.
If the measured resistance is less than 1.0
megohm or greater than 5.2 megohms, an
abnormality exists that must be corrected
before the unit is returned to the customer.
4. Leakage Current Hot Check (Figure 1-1):
Warning: Do not use an isolation
transformer during this test. Use a leakagecurrent tester or a metering system that
complies with American National Standards
Institute (ANIS C101.1, Leakage Current for
Appliances), and Underwriters Laboratories
(UL Publication UL1410, 59.7).
5. With the unit completely reassembled, plug
the AC line cord directly into the power
outlet. With the unit’s AC switch first in the
ON position and then OFF, measure the
current between a known earth ground (metal
water pipe, conduit, etc.) and all exposed
metal parts, including: antennas, handle
brackets, metal cabinets, screwheads and
control shafts. The current measured should
not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the
test.
Fig. 1-1 AC Leakage Test
6. Antenna Cold Check:
With the unit’s AC plug disconnected from the
AC source, connect an electrical jumper across
the two AC prongs. Connect one lead of the
ohmmeter to an AC prong. Connect the other
lead to the coaxial connector.
7. X-ray Limits:
The picture tube is especially designed to
prohibit X-ray emissions. To ensure continued
X-ray protection, replace the picture tube only
with one that is the same type as the original.
Carefully reinstall the picture tube shields and
mounting hardware; these also provide X-ray
protection.
8. High Voltage Limits:
High voltage must be measured each time
servicing is done on the B+, horizontal
deflection or high voltage circuits.
Correct operation of the X-ray protection
circuits must be reconfirmed whenever they
are serviced.
(X-ray protection circuits also may be called
“horizontal disable” or “hold-down”.)
Heed the high voltage limits. These include
the X–ray Protection Specifications Label, and
the Product Safety and X-ray Warning Note on
the service data schematic.
Precautions
Samsung Electronics 1-1
LEAKAGE
CURRENT
TESTER
DEVICE
UNDER
TEST
TEST ALL
EXPOSED METAL
SURFACES
3-WIRE CORD
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
EARTH
GROUND
(READING SHOULD
NOT BE ABOVE
0.5mA)
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential
hazards such as electrical shock and X-rays.
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified
limits by close-tolerance, safety-related
components and adjustments. If the high
voltage exceeds the specified limits, check
each of the special components.
10. Design Alteration Warning:
Never alter or add to the mechanical or
electrical design of this unit. Example: Do not
add auxiliary audio or video connectors. Such
alterations might create a safety hazard. Also,
any design changes or additions will void the
manufacturer’s warranty.
11. Hot Chassis Warning:
Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord. If an isolation transformer is not
used, these units may be safely serviced only
if the AC power plug is inserted so that the
chassis is connected to the ground side of the
AC source.
To confirm that the AC power plug is inserted
correctly, do the following: Using an AC
voltmeter, measure the voltage between the
chassis and a known earth ground. If the
reading is greater than 1.0V, remove the AC
power plug, reverse its polarity and reinsert.
Re-measure the voltage between the chassis
and ground.
12. Some TV chassis are designed to operate with
85 volts AC between chassis and ground,
regardless of the AC plug polarity. These units
can be safely serviced only if an isolation
transformer inserted between the receiver and
the power source.
13. Some TV chassis have a secondary ground
system in addition to the main chassis ground.
This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulating material that must not be defeated
or altered.
14. Components, parts and wiring that appear to
have overheated or that are otherwise
damaged should be replaced with parts that
meet the original specifications. Always
determine the cause of damage or
overheating, and correct any potential
hazards.
15. Observe the original lead dress, especially
near the following areas: Antenna wiring,
sharp edges, and especially the AC and high
voltage power supplies. Always inspect for
pinched, out-of-place, or frayed wiring. Do
not change the spacing between components
and the printed circuit board. Check the AC
power cord for damage. Make sure that leads
and components do not touch thermally hot
parts.
16. Picture Tube Implosion Warning:
The picture tube in this receiver employs
“integral implosion” protection. To ensure
continued implosion protection, make sure
that the replacement picture tube is the same
as the original.
17. Do not remove, install or handle the picture
tube without first putting on shatterproof
goggles equipped with side shields. Never
handle the picture tube by its neck. Some
“in-line” picture tubes are equipped with a
permanently attached deflection yoke; do not
try to remove such “permanently attached”
yokes from the picture tube.
18. Product Safety Notice:
Some electrical and mechanical parts have
special safety-related characteristics which
might not be obvious from visual inspection.
These safety features and the protection they
give might be lost if the replacement
component differs from the original—even if
the replacement is rated for higher voltage,
wattage, etc.
Components that are critical for safety are
indicated in the circuit diagram by shading,
( ) or ( ).
Use replacement components that have the
same ratings, especially for flame resistance
and dielectric strength specifications.
A replacement part that does not have the
same safety characteristics as the original
might create shock, fire or other hazards.
Precautions
1-2 Samsung Electronics
!
1-2 Servicing Precautions
1. Servicing precautions are printed on the
cabinet. Follow them.
2. Always unplug the unit’s AC power cord from
the AC power source before attempting to:
(a) Remove or reinstall any component or
assembly, (b) Disconnect an electrical plug or
connector, (c) Connect a test component in
parallel with an electrolytic capacitor.
3. Some components are raised above the printed
circuit board for safety. An insulation tube or
tape is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.
4. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the portion around
the serviced part has not been damaged.
5. Check the insulation between the blades of the
AC plug and accessible conductive parts
(examples: metal panels, input terminals and
earphone jacks).
6. Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the
power switch ON. Connect an insulation
resistance meter (500V) to the blades of the AC
plug.
The insulation resistance between each blade
of the AC plug and accessible conductive parts
(see above) should be greater than 1 megohm.
7. Never defeat any of the B+ voltage interlocks.
Do not apply AC power to the unit (or any of
its assemblies) unless all solid-state heat sinks
are correctly installed.
8. Always connect a test instrument’s ground
lead to the instrument chassis ground before
connecting the positive lead; always remove
the instrument’s ground lead last.
Precautions
Samsung Electronics 1-3
Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between
the servicing and safety precautions, always follow the safety precautions.
Warning2: An electrolytic capacitor installed with the wrong polarity might explode.
1. Some semiconductor (“solid state”) devices
are easily damaged by static electricity. Such
components are called Electrostatically
Sensitive Devices (ESDs); examples include
integrated circuits and some field-effect
transistors. The following techniques will
reduce the occurrence of component damage
caused by static electricity.
2. Immediately before handling any semicon
ductor components or assemblies, drain the
electrostatic charge from your body by
touching a known earth ground. Alternatively,
wear a discharging wrist-strap device. (Be
sure to remove it prior to applying power—
this is an electric shock precaution.)
3. After removing an ESD-equipped assembly,
place it on a conductive surface such as
aluminum foil to prevent accumulation of
electrostatic charge.
4. Do not use freon-propelled chemicals. These
can generate electrical charges that damage
ESDs.
5. Use only a grounded-tip soldering iron when
soldering or unsoldering ESDs.
6. Use only an anti-static solder removal device.
Many solder removal devices are not rated as
“anti-static”; these can accumulate sufficient
electrical charge to damage ESDs.
7. Do not remove a replacement ESD from its
protective package until you are ready to
install it. Most replacement ESDs are
packaged with leads that are electrically
shorted together by conductive foam,
aluminum foil or other conductive materials.
8. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.
9. Minimize body motions when handling
unpackaged replacement ESDs. Motions such
as brushing clothes together, or lifting a foot
from a carpeted floor can generate enough
static electricity to damage an ESD.
Precautions
1-4 Samsung Electronics
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
Reference Information
Samsung Electronics 2-1
2. Reference Information
2-1 Tables of Abbreviations and Acronyms
A
Ah
Å
dB
dBm
°C
°F
°K
F
G
GHz
g
H
Hz
h
ips
kWh
kg
kHz
kΩ
km
km/h
kV
kVA
kW
I
MHz
Ampere
Ampere-hour
Angstrom
Decibel
Decibel Referenced to One
Milliwatt
Degree Celsius
Degree Fahrenheit
degree Kelvin
Farad
Gauss
Gigahertz
Gram
Henry
Hertz
Hour
Inches Per Second
Kilowatt-hour
Kilogram
Kilohertz
Kilohm
Kilometer
Kilometer Per Hour
Kilovolt
Kilovolt-ampere
Kilowatt
Liter
Megahertz
MV
MW
MΩ
m
µA
µF
µH
µm
µs
µW
mA
mg
mH
mI
mm
ms
mV
nF
Ω
pF
Ib
rpm
rps
s
V
VA
W
Wh
Megavolt
Megawatt
Megohm
Meter
Microampere
Microfarad
Microhenry
Micrometer
Microsecond
Microwatt
Milliampere
Milligram
Millihenry
Milliliter
Millimeter
Millisecond
Millivolt
Nanofarad
Ohm
Picofarad
Pound
Revolutions Per Minute
Revolutions Per Second
Second (Time)
Volt
Volt-ampere
Watt
Watt-hour
Table 2-1 Abbreviations
Reference Information
2-2 Samsung Electronics
Table 2-2 Table of Acronyms
ABL
AC
ACC
AF
AFC
AFT
AGC
AM
ANSI
APC
APC
A/V
AVC
BAL
BPF
B-Y
CATV
CB
CCD
CCTV
Ch
CRT
CW
DC
DVM
EIA
ESD
ESD
FBP
FBT
FF
FM
FS
GND
G-Y
H
HF
HI-FI
IC
IC
IF
Automatic Brightness Limiter
Alternating Current
Automatic Chroma Control
Audio Frequency
Automatic Frequency Control
Automatic Fine Tuning
Automatic Gain Control
Amplitude Modulation
American National Standards Institute
Automatic Phase Control
Automatic Picture Control
Audio-Video
Automatic Volume Control
Balance
Bandpass Filter
Blue-Y
Community Antenna Television (Cable TV)
Citizens Band
Charge Coupled Device
Closed Circuit Television
Channel
Cathode Ray Tube
Continuous Wave
Direct Current
Digital Volt Meter
Electronics Industries Association
Electrostatic Discharge
Electrostatically Sensitive Device
Feedback Pulse
Flyback Transformer
Flip-Flop
Frequency Modulation
Fail Safe
Ground
Green-Y
High
High-Frequency
High Fidelity
Inductance-Capacitance
Integrated Circuit
Intermediate Frequency
I/O
L
L
LED
LF
MOSFET
MTS
NAB
NEC
NTSC
OSD
PCB
PLL
PWM
QIF
R
RC
RF
R-Y
SAP
SAW
SIF
SMPS
S/N
SW
TP
TTL
TV
UHF
UL
UV
VCD
VCO
VCXO
VHF
VIF
VR
VTR
VTVM
TR
Input/output
Left
Low
Light Emitting Diode
Low Frequency
Metal-Oxide-Semiconductor-Field-Effect-Tr
Multi-channel Television Sound
National Association of Broadcasters
National Electric Code
National Television Systems Committee
On Screen Display
Printed Circuit Board
Phase-Locked Loop
Pulse Width Modulation
Quadrature Intermediate Frequency
Right
Resistor & Capacitor
Radio Frequency
Red-Y
Second Audio Program
Surface Acoustic Wave(Filter)
Sound Intermediate Frequency
Switching Mode Power Supply
Signal/Noise
Switch
Test Point
Transistor Transistor Logic
Television
Ultra High Frequency
Underwriters Laboratories
Ultraviolet
Variable-Capacitance Diode
Voltage Controlled Oscillator
Voltage Controlled Crystal Oscillator
Very High Frequency
Video Intermediate Frequency
Variable Resistor
Video Tape Recorder
Vacuum Tube Voltmeter
Transistor
Reference Information
Samsung Electronics 2-3
2-2 IC Line Up
IC-VIDEO SWITCH
IC-AUDIO SWITCH
TUNER-F/S "PAL B/G D/K,I,M,T R,181CH"
TUNER-F/S "PAL B/G D/K,I,M,T R,181CH"
IC-CMOS LOGIC
IC-AUDIO SWITCH
IC-POWER AMP
IC-POWER AMP
IC-VIDEO SWITCH
IC-OP AMP
IC-POWER AMP
IC-VEDIO SWITCH
IC-VOLTAGE COMP.
TR-POWER
TR-POWER
Block Des-Loc Part-Number IC Name
MAIN
IC601
IC701
IC702
IC703
TU01
TUP01
IC905
ICG01
ICS02
IC602
IC603
IC804
IC805
ICS01
IC802
IC803
IC101
1204-001775
1001-001073
1001-001113
1002-001193
AA40-00017A
AA40-00019A
1103-001213
0801-000314
1204-001113
1201-000407
1201-001026
1203-000203
1203-000203
1201-001114
1203-000293
1203-000298
1001-001038
MSP3410G-C5
TEA6415C
TEA6422
PCF8591P
TCLN318PA09A(S)
TCPN3081PC09A(S)
M24C16
74HCT86
TEA6422
TDA7050
TDA7265
SI3050
SI3050
TEA6425
KA7808
KA7809
SAA1300
Description
IC-SOUND PROCESSOR
IC-VIDEO SWITCH
IC-AUDIO SWITCH
IC-A/D & D/A CONVERTER
TUNER-F/S "PAL B/G D/K,I,M,T R,181CH"
TUNER-F/S "PAL B/G D/K,I,M,T R,181CH"
IC-EEPROM
IC-CMOS LOGIC
IC-AUDIO SWITCH
IC-POWER AMP
IC-POWER AMP
IC-POSI.ADJUST REG.
IC-POSI.ADJUST REG.
IC-VIDEO SWITCH
IC-POSI.FIXED REG.
IC-POSI.FIXED REG.
I/O PORT
POWER
ICD02
ICD603
ICS03
IC801
IC301
IC403
IC801S
IC803S
QH04
Q403
Q404
Q405
Q801
1201-000191
1201-001026
1001-000223
1203-000165
1204-000517
1202-000103
AA13-00018A
AA13-00024A
0502-000442
0505-000156
0505-001116
0502-001175
AA13-20004H
4558
TDA7265
TEA5114A
78R12
LA7845
LM393
STR-F6656
TNY253P
2SC4636RB
SE135N-LF12
IRF620
BUZ73A
2SC5446
IC-OP AMP
IC-POWER AMP
IC-VEDIO SWITCH
IC-POSI.ADJUST REG.
IC-VERTIVAL DEF.
IC-VOLTAGE COMP.
IC-HYBRID
IC-HYBRID
TR-POWER
FET-SILICON
FET-SILICON
TR-POWER
IC-HYBRID
Reference Information
2-4 Samsung Electronics
IC Name
CRT
DOLBY
Block Des-Loc Part-Number IC Name
Description
F-BOX
CRT
IC01
IC02
IC05
IC03
IC04
PIC01
PIC02
IC15
IC11
IC12
IC13
IC14
IC501
IC502
IC503
QF10
1204-001598
AA13-00095A
1204-001599
1105-001273
1105-001273
1204-001658
1203-001419
1203-000515
1203-001419
1203-001140
1203-001359
1203-000188
1201-001131
1201-001131
1201-001131
0502-000153
VPC3230D-A0
SDP01
DDP3310B-F5
416S1120
416S1120
SDA9489X-B22
4931
7042
4931
7039
1086
7033P
TDA6111Q
TDA6111Q
TDA6111Q
2SC2344-D
IC-VIDEO PROCESS
IC-ASIC
IC-VIDEO PROCESS
IC-DRAM
IC-DRAM
IC-PICTURE PROCESS
IC-VOLTAGE REGULATOR
IC-VOL. DETECTOR
IC-VOLTAGE REGULATOR
IC-VOL. DETECTOR
IC-POSI.FIXED REG.
IC-POSI.ADJUST REG.
IC-VIDEO AMP
IC-VIDEO AMP
IC-VIDEO AMP
TR-POWER
DOLBY
MICOM
QF09
IC504
IC601
IC602
IC901
IC902
IC903
ICT01
ICT02
0502-000131
1201-000010
1204-001198
1201-000541
AA13-30013H
1102-001010
1203-000515
1204-001579
1105-001315
2SA1011-D
2030
DPL3519A-A2
062
SDA30C264
27C040
7042
SDA5275-3P
4E170411
TR-POWER
IC-OP AMP
IC-DECODER
IC-OP AMP
IC-MCU
IC-EPROM
IC-VOL. DETECTOR
IC-OSD PRPCESSOR
IC-DRAM
Specifications
Samsung Electronics 3-1
3. Specifications
Specifications are subject to change.
Model
Dimensions
(mm)
Weight
Set
Transmitter
Tuning Ranges
Television System
Intermediate Frequency
Set
Transmitter
CS29A7HF9X
CS34A7HF9X
56.3 Kg
153 g (including batteries)
Hi Contrast Instant Reception Type
VHF (CH 1 ~ 12)
UHF (CH 21 ~ 69)
CATV (CH S1 ~ S40)
PAL,SECAM,NTSC4.43, NTSC3.58, PAL60
VHF, UHF: 75 ohm unbalanced type
Video: 38.9 MHz
Sound: (BG)334.4MHz, (I)32.9MHz, (D/K)32.4MHz
Chrominance Subcarrier: 34.47 MHz
862 (W) x 515 (D) x 585 (H)
54 (W) x 31.5 (D) x 220 (H)
Set
Transmitter
Picture Tube
Antenna Input
Power Supply
AC 110V~230V, 50Hz, 60 Hz
DC 1.5V (AAA Size) x 2
170 W
15 W x 2
Transmitter Adjustment: Infrared Rays Type
UHF/VHF electronic tuner fine tuning: Electronic Type
Electronic Function Adjustment
Power Consumption
Sound Output
Adjustment System
3-2 Samsung Electronics
MEMO
Samsung Electronics 4-1
4. Alignment and Adjustments
4-1 Adjustments
Usually, a color TV needs only slight touch-up adjustment upon installation. Check the basic
characteristics such as vertical size, horizontal size, and focus. Observe the picture and check for
good black and white details. There must be no objectionable color shading: If color shading is
present, demagnetize the receiver. If color shading persists, re-do purity and convergence adjustments.
Note :
1. This ‘4. Alignment and Adjustments’ applies to KS4A chassis applications.
2. AC Power Supply: 100~230 V
3. This service manual has been written on the basis of domestic remote-control model adopting KS4A
chassis. Depending on sales location and product specifications, some of specifications herein may
be changed.
KS4A contains a dynamic focus circuit. When CRT PCB, FBT or CRT is replaced, be sure to adjust
in the following sequence:
4-1-1 General Alignment Instructions
4-1-2 Focus Adjustment
Dynamic Focus Adjustment
1. Input a crosshatch pattern.
2. Select “Standard” from the menu,
3. Turn the Static Focus VR clockwise to set it to its maximum.
4. Turn the Dynamic Focus VR counterclockwise to set it to its
maximum.
5. Turn the Static Focus VR counterclockwise slowly for the clearest
center vertical line.
<FBT FOCUS PACK>
6. Turn the Dynamic Focus VR clockwise slowly for the clearest third line.
7. Check for the FOCUS of entire screen. If necessary, re-do adjustments 3~6.
STATIC FOCUS VR
NO USE
After Adjustment
1
2
3
H
DYNAMIC FOCUS VR
V
4-2 Samsung Electronics
4-1-3 Screen Voltage Adjustment
1. Use a DC multi-meter to identify RK, GK, BK. And then adjust FBT Screen VR so that the highest
voltage becomes 175 Vp-p.
4-1-4 White Balance Adjustment
1. Select “Standard” from the menu.
2. Input an 100% White pattern.
3. In standby, press the remote-control keys in the following sequence:
Display Menu,Mute, Power on the TV set.
4. Warm up the TV set at least for 30 minutes.
5. Input a stair signal.
6. Use the Volume +/- buttons on the remote-control to select R Drive,G Drive,B Drive,Sub Cont.
7. Adjust Low-Light while viewing the darker side of screen.
8. Use the Volume +/- buttons on the remote-control to select Rcutoff,Gcutoff,Bcutoff,Sub Brt.
9. Adjust High-Light while viewing the brighter side of screen.
10. If not proper, re-adjust White Balance.
11. Press the Memory button to exit.
4-1-5 Sub-Brightness Adjustment
1. In standby, press the remote-control keys in the following sequence:
Display Menu Mute Power on the TV set.
2. Use the Channel Up/Down buttons to receive the sub bright adjustment signal.
3. Use the Volume +/- buttons to select SBT.
4. Press the Menu or Mute button on the remote control to adjust so that the seventh step on
the right of screen cannot be seen.
5. Press the Memory button to exit.
Samsung Electronics 4-3
4-2 MICOM PINNING
4-2-1 MICOM PINNING (SDA30C264)
RXD
IR
P3.4
P3.3
P3.2
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
NC
NC
P3.1
P3.0
P1.6
P1.5
P1.4
P1.3
P1.2
P1.1
P1.0
VSS
VDD
XTAL2
XTAL1
RST
ALE
A16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
A14
A15
VGA-ID
BS-POWER
TO;T
LED1
LED2
POWER
D-COIL
TXD
GNDD
VDDD
XTAL2
XTAL1
RESET
A16
M3L ENABLE
M3L DATA
M3L CLK
P3.6
P3.5
VDDA
VDDA
P3.7
A3
A3
VSSA
NC
P2.0
VSSA
SDA30C264
A5
A6
A8
A7
A13
A12
,AOM AFT
KEYS2
P2.2
P2.1
A10
A4
A11
FACORY
KEYS1
P0.7
P2.3
D6
D7
S | RESET
S | MUTE
P0.5
P0.6
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
D5
D0
P0.4 WP
P0.3 SCL2
P0.2 SDA2
P0.1 SDA1
P0.0 SCL1
P4.1 A18
P4.0 A17
VDD VDDD
VSS VSSD
A2 A2
A1 A1
A0 A0
D3 D3
D2 D2
D4 D4
D1 D1
D5
D0
D6
D7
A10
A4
A11
A5
A6
A8
A7
A13
A12
A14
A15
4-4 Samsung Electronics
4-2-1 MICOM FACTORY MODE OPTION BYTE
Ite
m
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
OSD
CRT
Language
Group
Lgnguage
ATM
Scart/Rca
VGA
Plug&Play
Dolby prg
Pinp
Cw/Cs
Lna
Child Lock
HP jack ident
Top ttx
High
Deviation
TTX group
Carrier
mute
CIS
4:3
Europe
Russia
ON
Scart
ON
ON
ON
CS
ON
ON
ON
ON
OFF
ON
Russia
OFF
Asia/Mid
dleEast
4:3
Asia
By
Destination
OFF
Rca
ON
ON
ON
ON
CS
ON
ON
ON
OFF
ON
By
Destination
OFF
Remark
-CPT Option(Wide/4:3):P.Size format, WSS Related Option
-User Optional Language Group Setting(Europe/Asia)
-Refer to “Language Group Table”
-Select the language of destination from Language Group
* Note: Countermeasute to prevent IRAN from smuggling Once
Arabic(Persian)has been selected,the user can’t select Persian(Arabic)
-ON: ATM, OFF: Auto search
-SCART: AV-Link,AV Setup Menu, Scart jack switching
-RCA: RCA Jack switching, DVD
-Presence of VGA(ON/OFF)
Application of Dolby Prologic(ON/OFF)
-Application of Plug & Play (ON/OFF)
-Application of Pinp(ON/OFF)
-CW/CS Tuner switching option
-Application of LNA(Pinp model) (ON/OFF)
-Application of Child Lock (ON/OFF)
-ON:The main sound is cut off after identigying the headphome jack
-OFF:The headphome jack ident PIN of MICOM is used as an IIC STOP
PIN. The main sound is not cut off
-Set only the countries requesting TOP patent so that TOP TTX can be
available(Countries using TOP:Germany,Austria,Italy,Swiss)
-Solve the Sound Stop problem by tutning High Deviation On for the
countries with SOUND over modulation
-Grouping the TTX Language by Region:Refer to a separate TABLE
-For Italy Only (Option)
Samsung Electronics 4-5
4-2-2 MICOM MODULE PIN ALIGNMENT
PIN NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
PAL MODULE
29MHz
GND
AV-LINK
5VB
MAIN AFT
CVBS
TILT
OSD/TTX-F/B
OSD/TTX-R
OSD/TTX-G
OSD/TTX-B
GND
VS2
HS2
GND
SDA2
PIN NO
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
PAL MODULE
SCL2
IIC STOP
SDA1
SCL1
WP
S-MUTE
S-RESET
VGA-ID
STD 5V
GND
KEYS1
KEYS2
IR
LED1
LED2
D-COIL
POWER
4-6 Samsung Electronics
4-2-3 MICOM PORT ASSIGNMENT
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
FUNCTION
P3.1
P3.0
P1.6
P1.5(PWM)
P1.4
P1.3
P1.2
P1.1
P1.0
VSS
VDD
XTAL2
XTAL1
RST
ALE
A16
A15
A14
A12
A13
A7
A8
A6
A9
A5
A11
ASSIGN
VGA-ID
NC
TILT
LED1
LED2
POWER
D-COIL
TXD
GNDD
VDDD
XTAL2
XTAL1
RESET
NC
A16
A15
A14
A12
A13
A7
A8
A6
A9
A5
A11
IN/OUT
IN
OUT
OUT
OUT
OUT
OUT
OUT
OUT
-
IN
OUT
IN
IN
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
ACTIVE H/L
LOW
LOW
-
PWM
-
LOW
LOW
GND
STD 5V
-
LOW
-
-
-
-
-
-
-
-
-
-
-
EXPLANATION
VGA SIGNAL IDENT
-
TILT CONTROL
ON/OFF LED CONTROL
TIMER LED CONRTOL
PICTURE ON PORT
D-COIL CONTROL
AV LINK CONTROL
DIGITAL GND
DIGITAL VCC
12MHz XTAL
MICOM TESET PORT
NOT USED
EPROM CONTROL ADDRESS
EPROM CONTROL ADDRESS
EPROM CONTROL ADDRESS
EPROM CONTROL DATA/ADDRESS
EPROM CONTROL DATA/ADDRESS
EPROM CONTROL DATA/ADDRESS
EPROM CONTROL DATA/ADDRESS
EPROM CONTROL DATA/ADDRESS
EPROM CONTROL DATA/ADDRESS
EPROM CONTROL DATA/ADDRESS
EPROM CONTROL DATA/ADDRESS
EPROM CONTROL DATA/ADDRESS
Samsung Electronics 4-7
NO
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
FUNCTION
A4
A10
D7
D6
D0
D5
D1
D4
D2
D3
A0
A1
A2
VSS
VDD
A17/P4.0
A18/P4.1
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
P2.3(A/D)
ASSIGN
A4
A10
D7
D6
D0
D5
D1
D4
D2
D3
A0
A1
A2
VSSD
VDDD
A17
A18
SCL1
SDA1
SDA2
SCL2
WP
S-MUTE
S-RESET
FACTORY
KEY1
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
-
IN
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
OUT
OUT
OUT
IN
IN
ACTIVE H/L
-
-
-
-
-
-
-
-
-
-
-
-
-
GND
STD 5V
-
-
-
-
-
HIGH
HIGH
LOW
LOW
-
EXPLANATION
EPROM CONTROL DATA/ADDRESS
“
“
“
“
“
“
“
“
“
EPROM CONTROL ADDRESS
EPROM CONTROL ADDRESS
EPROM CONTROL ADDRESS
DIGITAL GND
DIGITAL VCC
EPROM CONTROL ADDRESS
EPROM CONTROL ADDRESS
EPROM CONTROL BUS
EPROM CONTROL BUS
SLAVE IC CONTROL BUS
SLAVE IC CONTROL BUS
EEPROM WRITE PROTECTION
MAIN SOUND AMP MUTE
MSP RESET
BIS ADJ.MODE SELECTION
CH.UP ,CH.DOWN,VOL.UP,VOL.DOWN,MENU
4-8 Samsung Electronics
NO
53
54
55
56
57
58
59
60
61
62
63
64
FUNCTION
P2.2(A/D)
P2.1(A/D)
P2.0(A/D)
VSSA
A3
VDDA
P3.7
P3.6
P3.5
P3.4
P3.3
P3.2
ASSIGN
KEY2
MAIN AFT
P2.0(A/D)
VSSA
A3
VDDA
M3L CLK
M3L DATA
M3L ENABLE
RXD
IR
IN/OUT
IN
IN
-
IN/OUT
IN
IN/OUT
IN/OUT
OUT
IN
IN
IN
ACTIVE H/L
-
GND
-
STD 5V
-
-
-
HIGH
-
EXPLANATION
MUTE, TV/VIDEO
ANALOG GND
EPROM CONTROL ADDRESS
ANALOG VCC
SDA5275 MEGATEXT IC CONTROL BUS
“
“
AV LINK
REMOTE CONTROL SIGNALINPUT
00 PKRD 03
01 BRCT 00
02 R Drive 200
03 B Drive 200
04 G Drive 200
05 Sub Curoff 06
06 Ibrm 180
07 R Cutoff 80
08 B Cutoff 80
09 G Cutoff 80
10 Sub Brt. 10
11 Sub Color 08
Samsung Electronics 4-9
4-3 FACTORY MODE CONTROL
1. Enter & Concel the Factory Mode
1) Usual Remote Control
Enter : PICTURE OFF -> DISPLAY KEY -> MENU KEY -> MUTE KEY
(Press each remote control key with in 3 seconds)
Cannel : POWER OFF -> ON
2) Factory Remote Control
Enter : DISPLAY KEY -> FACTORY KEY
(Press each remote control key with in 3 seconds)
Cannel : POWER OFF -> ON
Press the FACTORY key twice at intervals of at lease 1 second.
(Enter the AGING Mode once)
3) Set Value When Entering the Factory Mode
- Picture Mode & Sound Mode are set to the standard data
4) Adjustments
- CH. UP/DOWN Key : Use to select the item you want
- VOLUME UP/DOWN Key : Increases or decreases the value of data.
- MENU Key : Use to save the current set value in EEPROM and exit to the upper mode.
- Use the DIGIT Key to switch channels
- Use the TV/VIDEO Key th conver to the AV Mode
4-3-1 Factroy Mode Data Control
Service Mode
Video Adjustment
Y.C-Delay
Deflection normal
Deflection VGA
Option byte
Reset
12 Sub Tint 04
13 V Peaking 07
14 Svm Gain 32
15 Svm Delay 05
16 Svm Limit 85
17 Ttx Cont 120
18 Ttx brt 15
19 Pip Cont 00
20 Bcl Thrs 41
21 Bcl Tc 153
22 Bcl Gain 15/25
23 Bcl Mc 145
24 Ymax 123
25 TB_REL 204
26 BCL_TCUP 02
4-4 FACTORY MODE MENU
Video Adjustment
4-10 Samsung Electronics
REMARK
DDP3310 R,1AEhex BIT(7:5)
-USER PEAKING CONRTOL REDUCTION (The bigger the
value is the larger the amount of REDUCTION)
VPC3230 FP BLOCK R,52hex (BIT(7:0)), R,53hex(BIT(5:0))
Reproduce the levels under BLACK LEVEL (When the
level=1,the levels under BLACK LEVEL are reproduced)
WHITE DRIVE CONTROL
- After all the SCREEN adjustments are complete, fix the
value of G DRIVE and adjust HIGH LIGHT WHITE
BALANCE.
DDP3310 R,1B1hex Bit <5:0> (Use 12 steps out of 63 steps
to add the value of sub cont to the contrast control of picture
control)
DDP3310 R,168hex (Internal brightness for measurement)
- Fixed Value by CRT
CUTOFF DRIVE CONRTOL
- After all the SCREEN adjustments are complete, fix the
value of G DRIVE and adjust LOW LIGHT WHITE
BALANCE.
DDP3310 R,167hex Bit<15:6>(Add the value of Sub
Brightness to Brightness Control of Picture Control)
DDP3310 R,1B2hex Bit<15:9>(Use 12 steps out of 63 steps
to add the value of sub color to the color control of picture
control)
VPC3230 FP Sub R,DChex - NTSC only
VPC3230 FP Sub R,28hex Bit<11:8>(Vertical peaking control)
DDP3310 R,1A7hex Bit<5:0>(VM gain control)
DDP3310 R,19Bhex Bit<3:0>(VM gain control)
DDP3310 R,19FBhex Bit<7:0>(VM limit value control)
Set TTX mode conrtast level
DDP3310 EXT BRIGHTNESS
SDA9489X R,11hex Bit<7:4>(PIPcontrast adjustment)
DD3310 R,160hex Bit <15:4>(ABL thresh hold setting)
- Set ABLOperation Point (Cuve Point)
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
OS D
PKRD
BRCT
R DRIVE
B DRIVE
G DRIVE
Sub Cont
Lbrm
R Cutoff
B Cutoff
G Cutoff
Sub Brt.
Sub Color
Sub Tint
V Peaking
Svm Gain
Svm Delay
Svm Limit
Ttx Cont
Ttx brt
Pip Cont
Bcl Thrs
Range
0-7
0-1
0-255(X2)
0-255(X2)
0-255(X2)
0-12
0-255
0-255
0-255
0-255
0-20(X8)
0-12
0-12
0-12
0-63
0-15
0-255
0-255
-128-127
0-15
0-255(X8)
29A7
3
0
200
200
200
6
180
80
80
80
6
8
4
7
32
5
85
120
15
0
41
Samsung Electronics 4-11
Item
21
22
23
24
25
26
Range
0-255(X2)
0-255(X2)
0-255(X2)
0-255(X2)
0-255(X2)
0-255
29A7
153
15/25
145
123
204
02
REMARK
DDP3310 R,161hex Bit<8:0>(ABL reduction time constamt setting)
DDP3310 R,162hex Bit<14:6>(ABL curve setting)
-Set the tilt between ABL Operation Point (Curve
Point)and MAX BEAM
DDP3310 R,163hex Bit<14:6>(Minimum RGB gain limiter)
Peak white drive limit
Peak white drive limit tilt point
ABL Cancel Conrtast Increase Time
OSD
Bcl Tc
Bcl Gain
Bcl Mc
Ymax
TB_REL
BCL_TCUP
00 Pal-B/G 00
01 Pal-D/K/L -3
02 Pal-I -3
03 Secam-B/G 03
04 Secam-D/K,L 02
05 Ntsc -1
06 Pal-av 01
07 Secam-av 03
08 Ntsc-av 01
Y.C-Delay
Item
00
01
02
03
04
05
06
07
08
Range
-3~3
29A7
00
-3
-3
03
02
-1
01
03
01
REMARK
VPC3230 FP Sub R, 23hex Bit<11:6> control(FIX)
-Set EEPROM MAP by system separately
-Video: Identified at VPC3230
-Sound: Identified at MSP3410
VPC3230 FP Sub R, 23hex Bit<11:6> control(FIX)
-Set EEPROM MAP by system separately
-Video: Identified at VPC3230
-Sound: Not Identified
OSD
Pal-B/G
Pal-D/K/L
Pal-I
Secam-B/G
Secam-D/K,L
Ntsc
Pal-av
Secam-av
Ntsc-av
4-12 Samsung Electronics
Deflection Normal
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
P.
P.
P.
P.
P.
P.
P.
P.
P.
P.
P.
P.
P.
P.
P.
P.
P.
P.
P.
P.
P.
P
P
P
P
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
V-SIZE
V-SFT
V-LIN
S-CORR
EW-WTH
EW-PBI
H-SFT
EW-TPZ
BOW
ANGLE
EW-UPCR
EW-LOCR
EHT TIME
HOR-EHT
VER-EHT
EHTVTRS
EHTV2
EHTH2
CRNU6
CRNL6
POFS2
HSYNC DLY
PHP
PVP
PHS
PVS
20
06
00
45
-71
43/25
24
00
00
00
-12
00
07
-24
-48/90
56
44
95
00
05
-103
93
28
32
00
00
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
OSD
P.(N)V-Size
P.(N)V-Sft
P.(N)V-Lin
P.(N)S-Corr
P.(N)EW-Wth
P.(N)EW-Pbl
P.(N)H-Sft
P.(N)EW-Tpz
P.(N)Bow
P.(N)Angle
P.(N)EW-UpCr
P.(N)EW-LoCr
EHT Time
P.(N)Hor-EHT
P.(N)Ver-EHT
Range
-128~127(X4)
-128~127
-128~127(X4)
-128~127(X4)
-128~127
-128~127
-128~127
-128~127
-128~127
-128~127
-128~127
-128~127
0~255(X2)
-128~127(X4)
-128~127(X4)
Initial Value
20
06
00
45
-71(200)
43(-128)
24
00
00
00
-12
00
07
-24
-48
Remark
DDP3310 R,14Dhex:VERTICAL SIZE ADJUSTMENT
DDP3310 R,14Fhex:VERTICAL SHIFTADJUSTMENT
DDP3310 R,150hex:VERTICAL LINEARITY ADJUSTMENT
DDP3310 R,151Dhex:VERTICAL S-CORRECTIONADJUSTMENT
DDP3310 R,157hex:HORI.SIZE ADJUSTMENT
DDP3310 R,159hex:HORI.PRABOLAADJUSTMENT
DDP3310 R,144hex:HORI. SHIFT ADJUSTMENT
DDP3310 R,158hex:TRAPEZOID DISTORTION F ACTOR
ADJUSTMENT
DDP3310 R,14Bhex:BOW ADJUSTMENT
DDP3310 R,14Ahex:PARALLELGRAM DISTORTION FACTOR
ADJUSTMENT
DDP3310 R,15Ahex:UP CONER 1/3 ADJUSTMENT
DDP3310 R,15Bhex:LOW CONER 1/3 ADJUSTMENT
DDP3310 R,15Dhex EHT OPERATION TIME CONSTANT(FIX)
EHT OPERATION AT OVER DDP3310 R,147hex EHTVTRS(FIX)
EHT OPERATION AT OVER DDP3310 R,15Chex EHTVTRS(FIX)
Samsung Electronics 4-13
Item
15
16
17
18
19
20
21
22
23
24
25
OSD
P.(N)EHIVTRS
P.(N)EHTV2
P.(N)EHTH2
P.(N)CRNL6
P.(N)CRNL6
P.(N)POFS2
P.(N)HSYNC
DLY
P(N)PHP
P(N)PVP
P(N)PHS
P(N)PVS
Range
-128~127(X8)
-128~127(X4)
-128~127(X4)
-128~127
-128~127
-128~127
0~255
0~255
0~255
0~15
0~15
Initial Value
56
44
95
00
05
-103
93
28
32
00
00
Remark
USE THE STEEP CURVE POINT OF HIGH VOLTAGE
TO SELECT BOTH EHTAND EHT2 OPERATIONS(FIX)
EHT OPERA TION A T LOW BEAM
(less than EHTVTRS)
UP CONER 1/6 ADJUSTEMENT(FIX)
LOW CONER 1/6 ADJUSTEMENT(FIX)
DDP3310 EXT .RGB(PIP,VGA,TTX/OSD)CLAMPING
ADJUSTMENT(FIX)
SDP01 HORI. SYNC DELAYADJUSTMENT
-EXT .RGB(PIP ,VGA,TTX/OSD)CLAMPING ADJUSTMENT(FIX)
PIP POSITION ADJUSTMENT
PICTURE POSITION INSIDE PIP ADJUSTMENT(FIX)
Deflection VGA
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
V-SIZE
V-SFT
V-LIN
S-CORR
EW-WTH
EW-PBI
H-SFT
EW-TPZ
BOW
ANGLE
EW-UPCR
EW-LOCR
EHT TIME
HOR-EHT
VER-EHT
EHTVTRS
EHTV2
EHTH2
CRNU6
CRNL6
POFS2
HSYNC DLY
PHP
PVP
20
06
00
45
-71
43
24
00
00
00
-12
00
07
-24
-48
255
00
00
05
04
24
93
32
32
4-14 Samsung Electronics
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
OSD
V-SIZE
V-SFT
V-LIN
S-CORR
EW-WTH
EW-PBI
H-SFT
EW-TPZ
BOW
ANGLE
EW-UPCR
EW-LOCR
EHT TIME
HOR-EHT
VER-EHT
EHTVTRS
EHTV2
EHTH2
CRNU6
CRNL6
POFS2
HSYNCDLY
PHP
PVP
Range
-128~127(4X)
-128~127
-128~127(4X)
-128~127(4X)
-128~127
-128~127
-128~127
-128~127
-128~127
-128~127
-128~127
-128~127
0~255(X2)
-128~127(4X)
-128~127(4X)
-128~127(8X)
-128~127(4X)
-128~127(4X)
-128~127
-128~127
-128~127
0~255
0~255
0~255
Initial Value
20
06
00
00
-71(200)
43(-128)
24
00
00
00
-12
00
07
-24
-48
255
00
00
05
04
24
93
32
32
Remark
DDP3310 R,14Dhex
DDP3310 R,14Fhex
DDP3310 R,150hex
DDP3310 R,151hex
DDP3310 R,157hex
DDP3310 R,159hex
DDP3310 R,144hex
DDP3310 R,158hex
DDP3310 R,14Bhex
DDP3310 R,14Ahex
DDP3310 R,15Ahex
DDP3310 R,15Bhex
DDP3310 R,15Dhex
DDP3310 R,147hex
DDP3310 R,15Chex
Samsung Electronics 4-15
4-5 3 Speed, Aging mode & Reset mode
1. 3-Speed
1) Speed up Analog Conrtol three times and Time Speed sixty times to let line productivity be
improved Analog Control.
2) Enter
- Display + 3Speed Key
3) Cancel
- The 3-Speed mode is cancelled in Master Power Off
- Press the 3Speed Key
4) OSD : The message “3-SPEED” appears on the center of screen
5) No Signal : No AUTO OFF
2. Aging Mode
1) Enter : DISPLAY KEY -> FACTORY KEY (FACTORY MODE)
-> FACTORY KEY (AGING MODE)
- When the AGING mode is entered, the OSD’s are displayed at 100% SIZE WHITE.
- Mute SOUND
2) Cancel
- FACTORY remote conrtol -> Press the FACTORY Key
- LOCAL KEY -> Use the Key MATRIX (Panel Key)
- The AGING mode remains even in MASTER S/W OFF -> ON
Cancel the AGING mode only in the above two cases.
3. Factory Reset
1) Run “Reset” on the Factory Menu.
2) Initialize the other user control data except the items that are adjusted in the Factory Mode.
3) Power Off in standby mode.
1. Bus Stop Mode (Use a Micom Stop Pin)
1) Enter the Bus Stop Mode within 200ms when 12c Stop Port is acknowledaged “LOW”.
2) Settings when entering.
- Set the screen mode “STANDARD”.
- Set Bus Line Free.
- Cancal the Bus Stop Mode when 12c Stop Port is acknowledged “High”.
3) Setting when cancelling
- Re-load data from EEPROM and then re-set the appropriate IC.
2. Remot Control Adjustment Mode (Factory Auto Adjustment)
1) Enter the Remote Control Adjustment Mode when the remote control auto adjustment code is input.
2) Settings when entering.
- Set the screen mode “STANDARD”
- Set Bus Line Free.
3) Cancel the Remote Control Adjustment Mode when the usual key code is input.
4) When the code is input, write data in both E2PRM and the appropriate IC within 20ms.
Interval between Code Inputs : 30ms
4-5-1 3-Speed
4-5-2 Bus Stop Mode & Remote Control Adjustment
Loading...