Samsung CS-29M40MH, CS-29K40ME, CS-29K40, CS-29M17MH, CS-29K40MH User Manual

Download

COLOUR TELEVISION

CS- 29140MH/29240PQ/29150/29K40MH/

29M17MH/29M40MH

Owner’s Instructions

Before operating, please read this manual thoroughly,

and retain it for future reference.

www.samsung.com/global/register

Connection Panel

The actual configuration of your TV may be different,

➢

depending on your model.

Rear Panel

(depending on the model)

Connecting to the RCA Output

The RCA66connectors are used for equipment, such as a recording VCR or audio system.

Connecting to the RCA

The RCA4 and RCA5 connectors are used for equipment, such as a VCR, DVD, decoder, satellite receiver, video game device, or video disc player. (When using the mono equipment, connect to the AUDIO-L input connector.) The RCA77connectors are used for equipment such as a DVD with component output (480i only).

Input

Control Panel

The product color and shape may very depending on

➢

the model.

Front (or Side) Panel

1 On-screen menu display 2 Volume adjustment 3 Channel selection 4 Remote control sensor 5 Standby indicator 6 Power on/off

◆ You can use the 3 buttons to switch the TV on when it is

in standby mode depending on the model.

◆ The 2 and 3 buttons also have the same function as the

œ/√/†/… buttons on the remote control.

◆ If the remote control no longer works or you have misplaced it, you can use the controls on the panel of the television.

(depending on the model)

cable television network

Whenever you connect an audio or video system to your

☛

television, ensure that all elements are switched off. Please be sure to match the color coded input terminals and cable jacks.

Connecting to an Aerial or Cable Television Network

Connect the aerial or network input cable to the 1 (75 Ω coaxial socket). To view television channels correctly, a signal must be received by the set from one of the sources: an outdoor aerial, cable television network, or satellite network. If you are using an indoor aerial, you may need to adjust it when tuning your television until you obtain a picture that is both sharp and clear.

Connecting to the SCART Input/Output

The SCART2 and SCART3 connectors are used for equipment, such as a VCR, DVD, decoder, satellite receiver, video game device, or video disc player. The SCART2 is also used for equipment with an RGB output, such as a video game device or video disc player.

Front (or Side) Panel

2 Video input

1 Audio input

2 Video input

Please be sure to match the colour coded input

☛

terminals and cable jacks.

Connecting to the RCA Input

The 1 (AUDIO-L/R) and 2 (VIDEO) connectors are used for equipment, such as a camcorder, video disc player, or video game device.

English - 1

continued...

AA68-03807A-03

Remote Control

(depending on the model)

Switching the Television On and Off

Operation of remote control may be affected by bright

➢

artificial light near to the TV.

Used to increase or decrease the volume.

Used to display the onscreen menu or return to the previous menu.

…… / †† / œœ / √√

Used to control the cursor in the menu.

S.MENU

Used to display the sound menu.

TURBO

Used to select the turbo sound option.

P.SIZE

Used to change the screen size.

DUAL I-II

Used to select the sound mode.

SOURCE

Used to display all of the available video sources.

INFO

Used to view the channel information and setting status you selected.

PRE-CH

Used to switch repeatedly between the last two channels displayed.

Used to display the next or previous stored channel.

EXIT

Used to exit from any display or return to normal viewing.

MUTE

Used to switch the sound off temporarily. To turn the sound back on, press the MUTE, , or

button.

ENTER

While using the onscreen menus, press the ENTER button to activate (or change) a particular item.

S.MODE

Used to select the sound effect.

((

P. MODE

Used to select the picture effect.

))

Used to return to the TV mode when it is in external input mode.

SLEEP

Used to select a preset time interval for automatic turn off.

The mains lead is attached to the rear of the television.

1 Plug the mains lead into an appropriate socket.

The main voltage is indicated on the rear of the

➢

television and the frequency is 50 or 60Hz.

2 Press the “I” button (On/Off) on the front (or side) of the

television.

3 Press the POWER button on the remote control to

switch the television on. The programme that you were watching last is re-selected automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Channel - Auto Store” or “Channel - Manual Store” on page 4.

If the television is initially powered on, several basic

➢

customer settings proceed automatically. Refer to “Setup - Plug & Play” on page 3.

4 To switch the television off, press the “I” button (On/Off)

on the front (or side) of the television.

Placing the Television in Standby Mode

The television can be placed in standby mode, in order to reduce power consumption and wear of the cathode ray tube. Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1 Press the POWER button on the remote control while

viewing. The television is in standby mode.

2 To switch the television back on, simply press it again.

POWER

Used to switch the TV on and off.

Numeric buttons

Used to select channels directly.

-/--

Used to select a channel numbered ten or over. Press this button, then “--” symbol is displayed. Enter the two-digit channel number.

Installing Batteries

Remove the cover. Install two AAA size batteries, then replace the cover. When the remote control does not operate normally, check that the “+” and “-” ends of the batteries are inserted correctly or the batteries are drained.

Do not mix battery types, i.e. alkaline and manganese.

➢

English - 2

Do not leave the television in standby mode for long

☛

periods of time (when you are away on holiday, for example). Turn the television off by pressing the “I” button (On/Off) on the front (or side) of the television. It is best to unplug the set from the mains and aerial.

Viewing the Menus

1 Press the MENU button.

The main menu is displayed on the screen. Its left side has five icons: Input, Picture, Sound, Channel, and Setup.

2 Press the … or † button to select one of the icons.

Press the ENTER button to access the icon’s sub-menu.

3 Press the … or † button to move to items in the menu.

Press the ENTER button to enter items in the menu.

4 Press the …/†/œ/√ button to change the selected

items. Press the MENU button to return to the previous menu.

5 Press the EXIT button to exit from the menu.

Setup - Plug & Play

When the television is initially powered on, several basic customer settings proceed automatically and subsequently. The following settings are available.

1 If the television is in standby

mode, press the POWER button on the remote control.

Start Plug & Play.

The is displayed. To start Plug & Play, press the ENTER button. The Language menu is displayed.

The Language menu

➢

will automatically appear after several seconds, even if the ENTER button is not pressed.

(depending on the model)

Plug & Play

Start Plug & Play.

Enter Return

Plug & Play

Language

lish

Eng

Indonesia Melayu

Français

Move Enter Skip

continued...

2 Select the appropriated language by pressing the … or

† button. Press the ENTER button.

The Check antenna input. is displayed.

If any language is not

➢

selected, the language menu will disappear

Plug & Play

Check antenna input.

Enter Skip

about 30 seconds later.

3 Make sure that the antenna

is connected to the television (refer to page 1). Press the ENTER button. The Area menu is displayed.

4 Press the … or † button to

select your area. Press the

ENTER button.

5 To search the channels,

press the ENTER button. To stop the search, press the ENTER button. When the channel searching has finished, the Clock Set menu is displayed.

6 Press the œ or √ button to

move to the hour or minute. Set the hour or minute by pressing the … or † button.

7 When you have finished,

press the MENU button. The Enjoy your

Plug & Play

Area

Asia/W.Europe

CIS/E.Europe China Hong Kong/UK Australia NZL/Indonesia

Move Enter Skip

Auto Store

Enter Skip

Auto Store

P 1 C-- 102MHz

Enter Skip

Clock Set --:-- am

Move Enter

Enjoy your watching.

South Africa America

Plug & Play

Start

Plug & Play

Stop

Plug & Play

Skip

watching. is displayed, and then the channel which

has been stored will be activated.

Re-setting the Plug & Play

Method: MENU ➜……/††(Setup) ➜ ENTER ➜……/††(Plug &

Play) ➜ ENTER

English - 3

Plug & Play

Language : English Time Child Lock Blue Screen : Off Melody : On Demonstration

Move Enter Return

Setup

7 %

Input

(depending on the model)

Source List / Edit Name

◆ Source List

You can switch between viewing signal from connected equipment, such

AV1 ---AV2 ---Componet ----

as a VCR, DVD, set-top box, and the TV source (broadcast or cable).

You can change the required external source simply

➢

by pressing the SOURCE button on the remote

Move Enter Return

control. It might take a short period of time for pictures to be switched. To return to the TV mode, press the TV button on the remote control.

◆ Edit Name

You can give a name to the external source.

AV1 : ----

AV2 : ---- Component : ----

Move Enter Return

Source List

Edit Name

----

VCR DVD Cable STB Satellite STB AV Receiver DVD Receiver

††

Important Warranty Information Regarding Television Format Viewing

Standard screen format televisions (4:3, the aspect ratio of the screen width to height) are primarily designed to view standard format full-motion video. The images displayed on them should primarily be in the standard 4:3 ratio format and constantly moving. Displaying stationary graphics and images on screen, such as the dark top and bottom letterbox bars (wide screen pictures), should be limited to no more than 15% of the total television viewing per week.

Wide screen format televisions (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature, and constantly moving. Displaying stationary graphics and images on screen, such as the dark sidebars on non-expanded standard format television video and programming, should be limited to no more than 15% of the total

√√

√√ √√ √√ √√ √√ √√

television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying any stationary images that exceed the above guidelines can cause uneven aging of picture tubes (CRTs) that leave subtle, but permanent burned-in ghost images in the television picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars. On television models that offer picture sizing features, use these controls to view the different formats as a full screen picture. Be careful in the selection and duration of television formats used for viewing. Uneven CRT aging as a result of format selection and use, as well as other burned-in images, is not covered by your Samsung limited warranty.

Channel - Auto Store

You can scan for the frequency ranges available to you (and availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However you can sort numbers manually and clear any channels you do not wish to watch.

Channels are sorted and stored in the order which reflects their position in the frequency range (with lowest first and highest last). The programme originally selected is then displayed.

To stop the search before it

➢

has finished, press the

ENTER button. When finished, the Sort menu is displayed. To sort the stored channels into the desired

Area : Belgie

Move Enter Return

P 1 C-- ----- 102MHz

Enter Return

Auto Store

Asia/W.Europe

CIS/E.Europe China Hong Kong/UK Australia NZL/Indonesia South Africa America

Stop

numerical order, refer to “Channel - Sort”. To exit without sorting, press the EXIT button.

Channel - Sort

This operation allows you to change the programme numbers of stored channels. This

From : P 1 -----

To : P-- ----Store : ?

operation may be necessary after using auto store.

◆ From: Channel number to

Move Adjust Return

be changed.

◆ To: New channel number to be identified.

◆ Store: Confirmation the exchange of channel numbers.

Sort

Channel - Manual Store

You can store channels, including those received via cable networks. When storing channels manually, you can choose:

Whether or not to store each of the channels found

The programme number of each stored channel which

Programme : P 3

Colour System : AUTO Sound System : BG Search : 46MHz Channel : C 1 Store : ?

Move Adjust Return

you wish to identify

◆ Programme (Programme number to be assigned to a channel)

◆ Colour System: AUTO/PAL/SECAM/NTSC4.43/NTSC3.58

◆ Sound System: BG/DK/I/M

◆ Search (When you do not know the channel numbers):

The tuner scans the frequency range until the first channel or the channel that you selected is received on the screen.

◆ Channel (When you know the number of the channel to be stored)

You can also select the channel number directly by

➢

pressing the numeric buttons (0~9).

◆ Store (When you store the channel and associated programme number)

If there is no sound or abnormal sound, re-select the

➢

sound standard required.

Channel mode

☛

◆ P (Programme mode): When completing tuning, the

broadcasting stations in your area have been assigned to position numbers from P00 to P99. You can select a channel by entering the position number in this mode.

◆ C (Real channel mode): You can select a channel by entering the assigned number for each air broadcasting station in this mode.

◆ S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this mode.

Manual Store

√√ √√

Channel - Add/Delete

You can exclude channels you have chosen from the channels you scanned. When you scan through the stored channels, those you have chosen to skip are not displayed. All of the channels that you did not

……

P 1 : Added

P 2 : Added P 3 : Added P 4 : Added P 5 : Added

††

Move Enter Return

specifically choose to skip are displayed during scanning.

Method: ENTER ➜ …/† ➜ ENTER : Select Added or Deleted.

Add/Delete

Channel - Fine Tune

If the reception is clear, you do not have to fine-tune the channel, as this is done automatically during the search and store operation. If however the signal is weak or distorted, you may have to fine-tune the channel manually.

Method: œ/√ : You can obtain a sharp and clear picture and good sound quality. …/† ➜ ENTER : You can reset the setting. MENU : You can memorise adjusted picture or sound.

Fine Tune

P 1 0

Reset

Move Adjust Return

English - 4

Channel - Name

Channel names will be assigned automatically when channel information is broadcast. These names can be changed, allowing you to assign new names.

Method:

……

P 1 : -----

P 2 : ----P 3 : ----P 4 : ----P 5 : -----

††

Move Enter Return

…/† : Used to select a letter or number. œ/√ : Used to move to the previous or next letter.

ENTER : Used to confirm the new name.

Name

Setup - Time

◆ Clock

You can set the television clock so that the current time is displayed when pressing the INFO button on the remote control. You must also set the time if you wish

Clock

Sleep Timer : Off On Timer Off Timer On Timer Channel : P 1 On Timer Volume : 10

Move Enter Return

to use the automatic on or off timers.

When pressing the “I” button (On/Off) on the front

➢

(or side) of the television, the clock setting will be reset.

◆ Sleep Timer

You can select a time period of between 30 and 180 minutes after which the television automatically switches to standby mode.

You can select these options simply by pressing the

➢

SLEEP button on the remote control. If the sleep timer is not yet set, Off is displayed. If it is already set, the remaining time before which the television switches to standby mode is displayed.

◆ On Timer / Off Timer

You can set the On/Off timers so that the television will switch on or off automatically at the time you select.

You must set the clock first.

☛

--:--

--:-- am

continued...

Time

Off Off

◆ On Timer Channel

The preferred channel can be set for when the timer automatically turns on the television.

◆ On Timer Volume

The preferred volume can be set for when the timer automatically turns on the television.

Auto Power Off

☛

When you set the timer “On”, the TV will eventually turn off, if no controls are operated for 3 hours after the TV was turned on by timer. This function is only available in timer “On” mode and prevents overheating, which may occur if a TV is on for too long.

Setup Language / Blue Screen / Melody / Demonstration

◆ Language

It is variable depending on the model. When you start using the television for the first time, you must select the language which will be used for displaying menus and indications.

Plug & Play Language : English Time Child Lock Blue Screen : Off Melody : On Demonstration

Move Enter Exit

Setup

√√ √√ √√ √√ √√ √√ √√

◆ Blue Screen

If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the Blue Screen to Off.

◆ Melody

√√

Setup - Child Lock

This feature allows you to prevent unauthorized users, such as children, from watching

Child Lock : On

Programme : P 1 Lock : ?

Child Lock

√√

You can hear melody sound when the television is powered on or off.

◆ Demonstration

To become familiar with the various menus provided by the television, you can view the in built demonstration. Each of the menu options is displayed in turn. To exit from the demonstration, press the EXIT button.

unsuitable programmes by muting out video and audio. Child Lock cannot be released using front (or side) panel

Move Enter Return

buttons. Only remote control can release the Child Lock setting, so keep the remote control away from children.

◆ Child Lock: On/Off

If you want to unlock a channel, set to Off.

◆ Programme: Channel number to be locked.

◆ Lock: When press the ENTER button, the Locked is

displayed.

If any channel is locked, you can not access to the

➢

Channel and Child Lock menu by using the control buttons on the TV panel (the Not available is displayed in the Child Lock menu). You can access by using the remote control only.

English - 5

Picture - Mode

◆ Mode: Dynamic/ Standard/Movie/Custom

You can select the type of picture which best corresponds to your viewing requirements.

You can select these

➢

options simply by pressing the P. MODE button on

Mode : Dynamic

Contrast : 100 Brightness : 50 Sharpness : 75 Colour : 50

Tint : G 50 R 50

Color Tone : Cool1 Reset

Move Enter Return

the remote control.

◆ Contrast/Brightness/Sharpness/Coluor/ Tint(NTSC only)

The television has several settings which allow you to control the picture quality.

◆ Colour Tone: Cool2/Cool1/Normal/Warm1/

Warm2

◆ Reset

You can return to the factory defaults. The reset function is set for each mode (Dynamic,

Standard, Movie, or Custom).

Mode

Picture Size / Digital NR / DNIe Jr / Tilt

◆ Size

You can select the picture size which best corresponds to your viewing requirements. It is variable depending on the model.

You can change the

➢

picture size simply by pressing the P.SIZE button on

Mode : Dynamic Size : Normal Digital NR : Off DNIe Jr : On Tilt : 0 PIP

Move Enter Exit

the remote control.

Picture

continued...

◆ Digital NR

If the signal received by the television is weak, you can

◆ Swap

You can interchange the main picture and sub-picture. 3

activate this feature to reduce any static and ghosting

√√

√√ √√

that may appear on the screen.

◆ DNIe Jr

(Digital Natural Image engine Junior)

This feature bring you more detailed image with detail enhancement, contrast enhancement and white enhancement. New image compensation algorithm gives brighter, clearer, much detailed image to you. DNIe Jr technology will fit every signals into your eyes.

◆ Size: Large/Small

You can select a size of the sub-picture.

◆ Position: / / /

You can select a position of the sub-picture.

◆ Programme

You can select a channel of the sub-picture only when the Source is set to TV.

◆ Tilt (depending on the model) If you find that the picture received is slightly tilted to one side, you can adjust the tilt setting (-7 to +7).

Easy functions of the remote control

You can freeze the sub-picture.

Picture - PIP

(depending on the model)

You can display a sub picture within the main picture of TV programme or external A/V devices such as VCR or DVD. In this way you can watch TV program or monitor the video input from any connected devices while watching TV or other video input.

Mode : Dynamic Size : Normal Digital NR : Off DNIe Jr : On Tilt : 0

PIP

Move Enter Return

Picture

√√ √√ √√ √√

√√

PIP : On

Source : TV Swap Size : Large Position : Programme : P 1

Move Enter Return

◆ PIP: On/Off

You can activate or deactivate the PIP funtion. 1

√√ √√ √√ √√

√√

◆ Source

You can select a source of the sub-picture. 2

Depending on the models, the sub-picture can be

➢

viewed only when a source different from the main picture's is selected. If a TV programme is viewed on the main picture, the sub-picture is not available for TV programmes. If a TV source is selected, the message Not Available is displayed.

PIP

√√

√√ √√ √√ √√

Sound Mode / Equalizer / Auto Volume / Pseudo Stereo /

Turbo Plus

◆ Mode: Standard/Music /Movie/Speech/Custom

You can select the type of special sound effect to be used when watching a given broadcast.

You can select these

➢

options simply by pressing the S.MODE button on

Mode : Standard Equalizer Auto Volume : Off Pseudo Stereo : Off Turbo Plus : Off

Move Enter Exit

the remote control.

Sound

√√ √√ √√ √√ √√

continued...

English - 6

◆ Equalizer

The television has several settings which allow you to control the sound quality.

If you make any changes to these settings, the

➢

sound mode is automatically switched to Custom.

◆ Auto Volume

Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.

◆ Pseudo Stereo

This feature converts a monaural sound signal into two identical left and right channels. Once the Pseudo Stereo is set to On or Off, these settings apply to the sound effects such as Standard, Music, Movie, and Speech.

◆ Turbo Plus

This feature suitably emphasizes both higher and lower bands of sound (and includes other effects). You can enjoy more magnificent and dynamic sound when watching music, movie, or other channels.

You can change the options simply by pressing the

➢

TURBO button on the remote control.

Teletext Feature

Most television stations provide written information services via teletext. The index page of the teletext service gives you information on how to use the service. In addition, you can select various options to suit your requirements by using the remote control buttons.

For teletext information to be displayed correctly,

☛

channel reception must be stable. Otherwise, information may be missing or some pages may not be displayed.

(depending on the model)

(sub-page)

Used to display the available sub-page.

(size)

Press to display the double-size letters in the upper half of the screen. For lower half of the screen, press it again. To display normal screen, press it once again.

(teletext on/mix)

Press to activate teletext mode after selecting the channel providing the teletext service. Press it again to overlap the teletext with the current broadcasting screen.

(mode)

Press to select the teletext mode (LIST/FLOF). If you press it in the LIST mode, it switches into the List save mode. In the List save mode, you can save teletext page into list using the

(store) button.

(reveal)

Used to display the hidden text (answers to quiz games, for example). To display normal screen, press it again.

(page up)

Used to display the next teletext page.

(page down)

Used to display the previous teletext page.

(cancel)

Used to display the broadcast when searching for a page.

Coloured buttons (red/green/yellow/blue)

If the FASTEXT system is used by a broadcasting company, the different topics covered on a teletext page are colourcoded and can be selected by pressing the coloured buttons. Press one of them corresponding to the required. The page is displayed with other coloured information that can be selected in the same way. To display the previous or next page, press the corresponding coloured button.

(store)

Used to store the teletext pages.

(hold)

Used to hold the display on a given page if the selected page is linked with several secondary pages which follow on automatically. To resume, press it again.

(index)

Used to display the index (contents) page at any time while you are viewing teletext.

English - 7

Troubleshooting

OSD Map

✽ : It is variable depending on the model.

Before contacting the Samsung after-sales service, perform the following simple checks. If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your local dealer.

No sound or picture

◆ Check that the mains lead has been connected to a wall socket.

◆ Check that you have pressed the “I” button (On/Off) and the POWER button.

◆ Check the picture contrast and brightness settings.

◆ Check the volume.

Normal picture but no sound

◆ Check the volume.

◆ Check whether the volume MUTE button on the

remote control has been pressed.

No picture or black and white picture

◆ Adjust the colour settings.

◆ Check that the broadcast system selected is correct.

Sound and picture interference

◆ Try to identify the electrical appliance that is affecting the television, then move it further away.

◆ Plug the television into a different mains socket.

Blurred or snowy picture, distorted sound

◆ Check the direction, location and connections of your aerial. This interference often occurs due to the use of an indoor aerial.

Remote control malfunctions

◆ Replace the remote control batteries.

◆ Clean the upper edge of the remote control

(transmission window).

◆ Check that the “+” and “-” ends of the batteries are inserted correctly.

◆ Check that the batteries are drained.

Input

Picture

Sound

Channel

Setup

Source List

Edit Name

Mode

Size

✽

Digital NR

DNIe Jr

✽

Tilt

✽

PIP

✽

Mode Equalizer Auto Volume Pseudo Stereo Turbo Plus

Auto Store

Manual Store

Add/Delete Fine Tune Name Sort

Plug & Play Language Time

Child Lock Blue Screen Melody Demonstration

✽

VCR / DVD / Cable STB / Satellite STB / AV Receiver / DVD Receiver / Game / Camcorder / DVD Combo

Dynamic / Standard / Movie / Custom

Contrast Brightness Sharpness Colour

(NTSC only)

Tint Colour Tone -Cool2 / Cool1 / Normal / Warm1 / Warm2 Reset

Off / On

PIP

Source

✽

Swap Size Position Programme

Standard / Music / Movie / Speech / Custom

Off / On Off / On Off / On

Area

✽

Search Programme Colour System ✽Sound System ✽Search Channel Store

Clock Sleep Timer On Timer Off Timer On Timer Channel On Timer Volume Off / On Off / On Off / On

Off / On

Asia/W.Europe / CIS/E.Europe / China / Hong Kong/UK / Australia / NZL/Indonesia / South Africa / America

AUTO / PAL / SECAM / NTSC4.43 / NTSC3.58 BG / DK / I / M

English - 8

Samsung CS-29M40MH, CS-29K40ME, CS-29K40, CS-29M17MH, CS-29K40MH User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Switching the Television On and Off

Placing the Television in Standby Mode

Viewing the Menus

Channel - Auto Store

Channel - Sort

Channel - Manual Store

Channel - Add/Delete

Channel - Fine Tune

Channel - Name

Setup - Time

Setup - Child Lock

Picture - Mode

Troubleshooting

OSD Map