Samsung CS29A7HF9 Schematic

COLOR TELEVISION RECEIVER

Chassis : KS4A(P) Model : CS29A7HF9X/XSV

CS29A7HF9XBBWT CS29A7HF9XWBWT WS32W2HF9X/BWT

COLOR TELEVISION RECEIVER CONTENTS

Precautions

Reference Information

Specifications

Alignment and Adjustments

Exploded Views and Parts List

Electrical Parts List

Block Diagrams

Schematic Diagrams

1.

2.

3.

4.

5.

6.

7.

8.

ELECTRONICS

Printed in Korea

3KS4A(P)-2910

1. Precautions

1-1 Safety Precautions

1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields.

2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers.

3. Make sure that there are no cabinet openings through which people—particularly children—might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers.

If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit’s AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check: With the unit’s AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector.

7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection.

8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced.

(X-ray protection circuits also may be called

“horizontal disable” or “hold-down”.)

Heed the high voltage limits. These include the X–ray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.

Precautions

Samsung Electronics 1-1

LEAKAGE CURRENT

TESTER

DEVICE UNDER

TEST

TEST ALL

EXPOSED METAL

SURFACES

3-WIRE CORD

ALSO TEST WITH

PLUG REVERSED

(USING AC ADAPTER

PLUG AS REQUIRED)

EARTH

GROUND

(READING SHOULD

NOT BE ABOVE

0.5mA)

Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components.

10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer’s warranty.

11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source.

To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground.

12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source.

13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered.

14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards.

15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts.

16. Picture Tube Implosion Warning: The picture tube in this receiver employs “integral implosion” protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original.

17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some “in-line” picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such “permanently attached” yokes from the picture tube.

18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original—even if the replacement is rated for higher voltage, wattage, etc.

Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.

Precautions

1-2 Samsung Electronics

!

1-2 Servicing Precautions

1. Servicing precautions are printed on the cabinet. Follow them.

2. Always unplug the unit’s AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor.

3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.

4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged.

5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug.

The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.

8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last.

Precautions

Samsung Electronics 1-3

Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between

the servicing and safety precautions, always follow the safety precautions.

Warning2: An electrolytic capacitor installed with the wrong polarity might explode.

1. Some semiconductor (“solid state”) devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity.

2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power— this is an electric shock precaution.)

3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge.

4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs.

5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs.

6. Use only an anti-static solder removal device. Many solder removal devices are not rated as “anti-static”; these can accumulate sufficient electrical charge to damage ESDs.

7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.

Precautions

1-4 Samsung Electronics

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

Reference Information

Samsung Electronics 2-1

2. Reference Information

2-1 Tables of Abbreviations and Acronyms

A Ah Å dB dBm

°C °F °K F G GHz g H Hz h ips kWh kg kHz kΩ km km/h kV kVA kW I MHz

Ampere Ampere-hour Angstrom Decibel Decibel Referenced to One Milliwatt Degree Celsius Degree Fahrenheit degree Kelvin Farad Gauss Gigahertz Gram Henry Hertz Hour Inches Per Second Kilowatt-hour Kilogram Kilohertz Kilohm Kilometer Kilometer Per Hour Kilovolt Kilovolt-ampere Kilowatt Liter Megahertz

MV MW MΩ m µA µF µH µm µs µW mA mg mH mI mm ms mV nF

Ω

pF Ib rpm rps s V VA W Wh

Megavolt Megawatt Megohm Meter Microampere Microfarad Microhenry Micrometer Microsecond Microwatt Milliampere Milligram Millihenry Milliliter Millimeter Millisecond Millivolt Nanofarad Ohm Picofarad Pound Revolutions Per Minute Revolutions Per Second Second (Time) Volt Volt-ampere Watt Watt-hour

Table 2-1 Abbreviations

Reference Information

2-2 Samsung Electronics

Table 2-2 Table of Acronyms

ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF

Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Control Balance Bandpass Filter Blue-Y Community Antenna Television (Cable TV) Citizens Band Charge Coupled Device Closed Circuit Television Channel Cathode Ray Tube Continuous Wave Direct Current Digital Volt Meter Electronics Industries Association Electrostatic Discharge Electrostatically Sensitive Device Feedback Pulse Flyback Transformer Flip-Flop Frequency Modulation Fail Safe Ground Green-Y High High-Frequency High Fidelity Inductance-Capacitance Integrated Circuit Intermediate Frequency

I/O L L LED LF MOSFET MTS NAB NEC NTSC OSD PCB PLL PWM QIF R RC RF R-Y SAP SAW SIF SMPS S/N SW TP TTL TV UHF UL UV VCD VCO VCXO VHF VIF VR VTR VTVM TR

Input/output Left Low Light Emitting Diode Low Frequency Metal-Oxide-Semiconductor-Field-Effect-Tr Multi-channel Television Sound National Association of Broadcasters National Electric Code National Television Systems Committee On Screen Display Printed Circuit Board Phase-Locked Loop Pulse Width Modulation Quadrature Intermediate Frequency Right Resistor & Capacitor Radio Frequency Red-Y Second Audio Program Surface Acoustic Wave(Filter) Sound Intermediate Frequency Switching Mode Power Supply Signal/Noise Switch Test Point Transistor Transistor Logic Television Ultra High Frequency Underwriters Laboratories Ultraviolet Variable-Capacitance Diode Voltage Controlled Oscillator Voltage Controlled Crystal Oscillator Very High Frequency Video Intermediate Frequency Variable Resistor Video Tape Recorder Vacuum Tube Voltmeter Transistor

Reference Information

Samsung Electronics 2-3

2-2 IC Line Up

IC-VIDEO SWITCH IC-AUDIO SWITCH

TUNER-F/S "PAL B/G D/K,I,M,T R,181CH" TUNER-F/S "PAL B/G D/K,I,M,T R,181CH"

IC-CMOS LOGIC IC-AUDIO SWITCH IC-POWER AMP IC-POWER AMP

IC-VIDEO SWITCH

IC-OP AMP IC-POWER AMP IC-VEDIO SWITCH

IC-VOLTAGE COMP.

TR-POWER

Block Des-Loc Part-Number IC Name

MAIN

IC601 IC701 IC702 IC703

TU01

TUP01

IC905 ICG01 ICS02 IC602

IC603

IC804 IC805

ICS01

IC802 IC803 IC101

1204-001775 1001-001073 1001-001113

1002-001193 AA40-00017A AA40-00019A

1103-001213

0801-000314

1204-001113

1201-000407

1201-001026

1203-000203

1201-001114

1203-000293

1203-000298

1001-001038

MSP3410G-C5

TEA6415C

TEA6422

PCF8591P

TCLN318PA09A(S)

TCPN3081PC09A(S)

M24C16

74HCT86

TEA6422

TDA7050 TDA7265

SI3050 SI3050

TEA6425

KA7808 KA7809

SAA1300

Description

IC-SOUND PROCESSOR IC-VIDEO SWITCH IC-AUDIO SWITCH IC-A/D & D/A CONVERTER TUNER-F/S "PAL B/G D/K,I,M,T R,181CH" TUNER-F/S "PAL B/G D/K,I,M,T R,181CH" IC-EEPROM IC-CMOS LOGIC IC-AUDIO SWITCH IC-POWER AMP IC-POWER AMP IC-POSI.ADJUST REG. IC-POSI.ADJUST REG. IC-VIDEO SWITCH IC-POSI.FIXED REG. IC-POSI.FIXED REG. I/O PORT

POWER

ICD02

ICD603 ICS03 IC801 IC301

IC403 IC801S IC803S

QH04

Q403 Q404 Q405 Q801

1201-000191 1201-001026 1001-000223 1203-000165

1204-000517

1202-000103 AA13-00018A AA13-00024A

0502-000442

0505-000156

0505-001116

0502-001175 AA13-20004H

4558

TDA7265

TEA5114A

78R12

LA7845

LM393

STR-F6656

TNY253P

2SC4636RB

SE135N-LF12

IRF620

BUZ73A

2SC5446

IC-OP AMP IC-POWER AMP IC-VEDIO SWITCH IC-POSI.ADJUST REG. IC-VERTIVAL DEF. IC-VOLTAGE COMP. IC-HYBRID IC-HYBRID TR-POWER FET-SILICON FET-SILICON TR-POWER IC-HYBRID

Reference Information

2-4 Samsung Electronics

IC Name

CRT

DOLBY

Block Des-Loc Part-Number IC Name

Description

F-BOX

CRT

IC01 IC02 IC05 IC03 IC04 PIC01 PIC02 IC15

IC11 IC12 IC13 IC14 IC501 IC502 IC503

QF10

1204-001598

AA13-00095A

1204-001599 1105-001273 1105-001273 1204-001658 1203-001419 1203-000515 1203-001419 1203-001140 1203-001359 1203-000188 1201-001131 1201-001131 1201-001131 0502-000153

VPC3230D-A0

SDP01

DDP3310B-F5

416S1120 416S1120

SDA9489X-B22

4931 7042

4931

7039 1086

7033P TDA6111Q TDA6111Q

TDA6111Q

2SC2344-D

IC-VIDEO PROCESS IC-ASIC IC-VIDEO PROCESS IC-DRAM IC-DRAM IC-PICTURE PROCESS IC-VOLTAGE REGULATOR IC-VOL. DETECTOR IC-VOLTAGE REGULATOR IC-VOL. DETECTOR IC-POSI.FIXED REG. IC-POSI.ADJUST REG. IC-VIDEO AMP IC-VIDEO AMP IC-VIDEO AMP TR-POWER

DOLBY

MICOM

QF09

IC504 IC601 IC602 IC901 IC902

IC903 ICT01

ICT02

0502-000131 1201-000010 1204-001198 1201-000541 AA13-30013H 1102-001010 1203-000515 1204-001579 1105-001315

2SA1011-D

2030

DPL3519A-A2

062

SDA30C264

27C040

7042

SDA5275-3P

4E170411

TR-POWER IC-OP AMP

IC-DECODER IC-OP AMP IC-MCU IC-EPROM IC-VOL. DETECTOR IC-OSD PRPCESSOR

IC-DRAM

Specifications

Samsung Electronics 3-1

3. Specifications

Specifications are subject to change.

Model

Dimensions

(mm)

Weight

Set

Transmitter

Tuning Ranges

Television System

Intermediate Frequency

Set

Transmitter

CS29A7HF9X CS34A7HF9X

56.3 Kg 153 g (including batteries) Hi Contrast Instant Reception Type VHF (CH 1 ~ 12) UHF (CH 21 ~ 69)

CATV (CH S1 ~ S40) PAL,SECAM,NTSC4.43, NTSC3.58, PAL60 VHF, UHF: 75 ohm unbalanced type Video: 38.9 MHz Sound: (BG)334.4MHz, (I)32.9MHz, (D/K)32.4MHz

Chrominance Subcarrier: 34.47 MHz

862 (W) x 515 (D) x 585 (H) 54 (W) x 31.5 (D) x 220 (H)

Set

Transmitter

Picture Tube

Antenna Input

Power Supply

AC 110V~230V, 50Hz, 60 Hz

DC 1.5V (AAA Size) x 2

170 W 15 W x 2

Transmitter Adjustment: Infrared Rays Type UHF/VHF electronic tuner fine tuning: Electronic Type Electronic Function Adjustment

Power Consumption Sound Output

Adjustment System

3-2 Samsung Electronics

MEMO

Samsung Electronics 4-1

4. Alignment and Adjustments

4-1 Adjustments

Usually, a color TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as vertical size, horizontal size, and focus. Observe the picture and check for good black and white details. There must be no objectionable color shading: If color shading is present, demagnetize the receiver. If color shading persists, re-do purity and convergence adjustments.

Note :

1. This ‘4. Alignment and Adjustments’ applies to KS4A chassis applications.

2. AC Power Supply: 100~230 V

3. This service manual has been written on the basis of domestic remote-control model adopting KS4A chassis. Depending on sales location and product specifications, some of specifications herein may be changed.

KS4A contains a dynamic focus circuit. When CRT PCB, FBT or CRT is replaced, be sure to adjust in the following sequence:

4-1-1 General Alignment Instructions

4-1-2 Focus Adjustment

Dynamic Focus Adjustment

1. Input a crosshatch pattern.

2. Select “Standard” from the menu,

3. Turn the Static Focus VR clockwise to set it to its maximum.

4. Turn the Dynamic Focus VR counterclockwise to set it to its maximum.

5. Turn the Static Focus VR counterclockwise slowly for the clearest center vertical line.

6. Turn the Dynamic Focus VR clockwise slowly for the clearest third line.

7. Check for the FOCUS of entire screen. If necessary, re-do adjustments 3~6.

STATIC FOCUS VR

NO USE

After Adjustment

1 2

3

H

DYNAMIC FOCUS VR

V

4-2 Samsung Electronics

4-1-3 Screen Voltage Adjustment

1. Use a DC multi-meter to identify RK, GK, BK. And then adjust FBT Screen VR so that the highest voltage becomes 175 Vp-p.

4-1-4 White Balance Adjustment

1. Select “Standard” from the menu.

2. Input an 100% White pattern.

3. In standby, press the remote-control keys in the following sequence:

Display Menu,Mute, Power on the TV set.

4. Warm up the TV set at least for 30 minutes.

5. Input a stair signal.

6. Use the Volume +/- buttons on the remote-control to select R Drive,G Drive,B Drive,Sub Cont.

7. Adjust Low-Light while viewing the darker side of screen.

8. Use the Volume +/- buttons on the remote-control to select Rcutoff,Gcutoff,Bcutoff,Sub Brt.

9. Adjust High-Light while viewing the brighter side of screen.

10. If not proper, re-adjust White Balance.

11. Press the Memory button to exit.

4-1-5 Sub-Brightness Adjustment

1. In standby, press the remote-control keys in the following sequence: Display Menu Mute Power on the TV set.

2. Use the Channel Up/Down buttons to receive the sub bright adjustment signal.

3. Use the Volume +/- buttons to select SBT.

4. Press the Menu or Mute button on the remote control to adjust so that the seventh step on the right of screen cannot be seen.

5. Press the Memory button to exit.

Samsung Electronics 4-3

4-2 MICOM PINNING

4-2-1 MICOM PINNING (SDA30C264)

RXD

IR

P3.4

P3.3

P3.2

64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49

NC

P3.1 P3.0 P1.6 P1.5 P1.4 P1.3 P1.2 P1.1 P1.0 VSS VDD XTAL2 XTAL1 RST ALE A16

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

A14

A15

VGA-ID

BS-POWER

TO;T LED1 LED2

POWER

D-COIL

TXD GNDD VDDD

XTAL2 XTAL1

RESET

A16

M3L ENABLE

M3L DATA

M3L CLK

P3.6

P3.5

VDDA

P3.7

A3 A3

VSSA

NC

P2.0

VSSA

SDA30C264

A5

A6

A8

A7

A13

A12

,AOM AFT

KEYS2

P2.2

P2.1

A10

A4

A11

FACORY

KEYS1

P0.7

P2.3

D6

D7

S | RESET

S | MUTE

P0.5

P0.6

48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33

D5

D0

P0.4 WP P0.3 SCL2 P0.2 SDA2 P0.1 SDA1 P0.0 SCL1 P4.1 A18 P4.0 A17 VDD VDDD VSS VSSD A2 A2 A1 A1 A0 A0 D3 D3 D2 D2 D4 D4 D1 D1

D5

D0

D6

D7

A10

A4

A11

A5

A6

A8

A7

A13

A12

A14

A15

4-4 Samsung Electronics

4-2-1 MICOM FACTORY MODE OPTION BYTE

Ite

m

0 1

2

3 4

5 6 7 8

9 10 11 12

13

14

15 16

OSD

CRT

Language

Group

Lgnguage

ATM

Scart/Rca

VGA

Plug&Play

Dolby prg

Pinp

Cw/Cs

Lna

Child Lock

HP jack ident

Top ttx

High

Deviation

TTX group

Carrier

mute

CIS

4:3

Europe

Russia

ON

Scart

ON ON ON CS ON

ON ON

ON

OFF

ON

Russia

OFF

Asia/Mid

dleEast

4:3

Asia

By

Destination

OFF

Rca

ON ON ON ON CS

ON

OFF

ON

By

Destination

OFF

Remark

-CPT Option(Wide/4:3):P.Size format, WSS Related Option

-User Optional Language Group Setting(Europe/Asia)

-Refer to “Language Group Table”

-Select the language of destination from Language Group

* Note: Countermeasute to prevent IRAN from smuggling Once

Arabic(Persian)has been selected,the user can’t select Persian(Arabic)

-ON: ATM, OFF: Auto search

-SCART: AV-Link,AV Setup Menu, Scart jack switching

-RCA: RCA Jack switching, DVD

-Presence of VGA(ON/OFF)

Application of Dolby Prologic(ON/OFF)

-Application of Plug & Play (ON/OFF)

-Application of Pinp(ON/OFF)

-CW/CS Tuner switching option

-Application of LNA(Pinp model) (ON/OFF)

-Application of Child Lock (ON/OFF)

-ON:The main sound is cut off after identigying the headphome jack

-OFF:The headphome jack ident PIN of MICOM is used as an IIC STOP PIN. The main sound is not cut off

-Set only the countries requesting TOP patent so that TOP TTX can be

available(Countries using TOP:Germany,Austria,Italy,Swiss)

-Solve the Sound Stop problem by tutning High Deviation On for the

countries with SOUND over modulation

-Grouping the TTX Language by Region:Refer to a separate TABLE

-For Italy Only (Option)

Samsung Electronics 4-5

4-2-2 MICOM MODULE PIN ALIGNMENT

PIN NO

1 2

3 4

5 6 7 8 9

10

11

12 13

14 15

16 17

18

PAL MODULE

29MHz

GND

AV-LINK

5VB

MAIN AFT

CVBS

TILT

OSD/TTX-F/B

OSD/TTX-R OSD/TTX-G

OSD/TTX-B

GND

VS2 HS2

GND

SDA2

PIN NO

19 20

21 22 23 24 25 26 27

28 29 30

31 32

33 34 35

PAL MODULE

SCL2

IIC STOP

SDA1 SCL1

WP

S-MUTE

S-RESET

VGA-ID STD 5V

GND KEYS1 KEYS2

IR

LED1 LED2

D-COIL

POWER

4-6 Samsung Electronics

4-2-3 MICOM PORT ASSIGNMENT

NO

1 2

3 4

5 6 7 8 9

10

11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

FUNCTION

P3.1 P3.0

P1.6

P1.5(PWM)

P1.4 P1.3 P1.2 P1.1 P1.0 VSS

VDD XTAL2 XTAL1

RST

ALE

A16 A15 A14 A12 A13

A7 A8 A6 A9 A5

A11

ASSIGN

VGA-ID

NC

TILT LED1 LED2

POWER

D-COIL

TXD

GNDD VDDD XTAL2 XTAL1

RESET

NC A16 A15 A14 A12 A13

A7 A8 A6 A9 A5

A11

IN/OUT

IN

OUT

OUT OUT OUT OUT OUT OUT

-

IN

OUT

IN IN

IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT

ACTIVE H/L

LOW LOW

-

PWM

-

LOW LOW

GND

STD 5V

-

LOW

-

EXPLANATION

VGA SIGNAL IDENT

-

TILT CONTROL

ON/OFF LED CONTROL

TIMER LED CONRTOL

PICTURE ON PORT

D-COIL CONTROL

AV LINK CONTROL

DIGITAL GND DIGITAL VCC

12MHz XTAL

MICOM TESET PORT

NOT USED

EPROM CONTROL ADDRESS EPROM CONTROL ADDRESS EPROM CONTROL ADDRESS

EPROM CONTROL DATA/ADDRESS

Samsung Electronics 4-7

NO

27 28 29

30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

FUNCTION

A4

A10

D7 D6

D0 D5 D1 D4 D2

D3 A0

A1 A2

VSS

VDD A17/P4.0 A18/P4.1

P0.0

P0.1

P0.2

P0.3

P0.4

P0.5

P0.6

P0.7

P2.3(A/D)

ASSIGN

A4

A10

D7 D6

D0 D5 D1 D4 D2

D3 A0

A1 A2

VSSD

VDDD

A17 A18

SCL1 SDA1 SDA2

SCL2

WP

S-MUTE

S-RESET

FACTORY

KEY1

IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT

-

IN IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT

OUT OUT OUT

IN

ACTIVE H/L

-

GND

STD 5V

-

HIGH HIGH

LOW LOW

-

EXPLANATION

EPROM CONTROL DATA/ADDRESS

“

EPROM CONTROL ADDRESS EPROM CONTROL ADDRESS EPROM CONTROL ADDRESS

DIGITAL GND

DIGITAL VCC EPROM CONTROL ADDRESS EPROM CONTROL ADDRESS

EPROM CONTROL BUS

EPROM CONTROL BUS SLAVE IC CONTROL BUS SLAVE IC CONTROL BUS

EEPROM WRITE PROTECTION

MAIN SOUND AMP MUTE

MSP RESET

BIS ADJ.MODE SELECTION

CH.UP ,CH.DOWN,VOL.UP,VOL.DOWN,MENU

4-8 Samsung Electronics

NO

53 54 55 56 57 58 59 60 61 62 63 64

FUNCTION

P2.2(A/D) P2.1(A/D)

P2.0(A/D)

VSSA

A3

VDDA

P3.7 P3.6 P3.5 P3.4 P3.3 P3.2

ASSIGN

KEY2

MAIN AFT

P2.0(A/D)

VSSA

A3

VDDA

M3L CLK

M3L DATA

M3L ENABLE

RXD

IR

IN/OUT

IN IN

-

IN/OUT

IN IN/OUT IN/OUT

OUT

IN

ACTIVE H/L

-

GND

-

STD 5V

-

HIGH

-

EXPLANATION

MUTE, TV/VIDEO

ANALOG GND

EPROM CONTROL ADDRESS

ANALOG VCC

SDA5275 MEGATEXT IC CONTROL BUS

“ “

AV LINK

REMOTE CONTROL SIGNALINPUT

00 PKRD 03 01 BRCT 00 02 R Drive 200 03 B Drive 200 04 G Drive 200 05 Sub Curoff 06 06 Ibrm 180 07 R Cutoff 80 08 B Cutoff 80 09 G Cutoff 80 10 Sub Brt. 10 11 Sub Color 08

Samsung Electronics 4-9

4-3 FACTORY MODE CONTROL

1. Enter & Concel the Factory Mode

1) Usual Remote Control Enter : PICTURE OFF -> DISPLAY KEY -> MENU KEY -> MUTE KEY

(Press each remote control key with in 3 seconds)

Cannel : POWER OFF -> ON

2) Factory Remote Control Enter : DISPLAY KEY -> FACTORY KEY (Press each remote control key with in 3 seconds) Cannel : POWER OFF -> ON Press the FACTORY key twice at intervals of at lease 1 second.

(Enter the AGING Mode once)

3) Set Value When Entering the Factory Mode

- Picture Mode & Sound Mode are set to the standard data

4) Adjustments

- CH. UP/DOWN Key : Use to select the item you want

- VOLUME UP/DOWN Key : Increases or decreases the value of data.

- MENU Key : Use to save the current set value in EEPROM and exit to the upper mode.

- Use the DIGIT Key to switch channels

- Use the TV/VIDEO Key th conver to the AV Mode

4-3-1 Factroy Mode Data Control

Service Mode Video Adjustment Y.C-Delay Deflection normal Deflection VGA Option byte Reset

12 Sub Tint 04 13 V Peaking 07 14 Svm Gain 32 15 Svm Delay 05 16 Svm Limit 85 17 Ttx Cont 120 18 Ttx brt 15 19 Pip Cont 00 20 Bcl Thrs 41 21 Bcl Tc 153 22 Bcl Gain 15/25 23 Bcl Mc 145

24 Ymax 123 25 TB_REL 204 26 BCL_TCUP 02

4-4 FACTORY MODE MENU

Video Adjustment

4-10 Samsung Electronics

REMARK

DDP3310 R,1AEhex BIT(7:5)

-USER PEAKING CONRTOL REDUCTION (The bigger the value is the larger the amount of REDUCTION) VPC3230 FP BLOCK R,52hex (BIT(7:0)), R,53hex(BIT(5:0)) Reproduce the levels under BLACK LEVEL (When the level=1,the levels under BLACK LEVEL are reproduced)

WHITE DRIVE CONTROL

- After all the SCREEN adjustments are complete, fix the value of G DRIVE and adjust HIGH LIGHT WHITE BALANCE.

DDP3310 R,1B1hex Bit <5:0> (Use 12 steps out of 63 steps to add the value of sub cont to the contrast control of picture control)

DDP3310 R,168hex (Internal brightness for measurement)

- Fixed Value by CRT

CUTOFF DRIVE CONRTOL

- After all the SCREEN adjustments are complete, fix the value of G DRIVE and adjust LOW LIGHT WHITE BALANCE.

DDP3310 R,167hex Bit<15:6>(Add the value of Sub Brightness to Brightness Control of Picture Control)

DDP3310 R,1B2hex Bit<15:9>(Use 12 steps out of 63 steps to add the value of sub color to the color control of picture control)

VPC3230 FP Sub R,DChex - NTSC only

VPC3230 FP Sub R,28hex Bit<11:8>(Vertical peaking control)

DDP3310 R,1A7hex Bit<5:0>(VM gain control)

DDP3310 R,19Bhex Bit<3:0>(VM gain control)

DDP3310 R,19FBhex Bit<7:0>(VM limit value control)

Set TTX mode conrtast level

DDP3310 EXT BRIGHTNESS

SDA9489X R,11hex Bit<7:4>(PIPcontrast adjustment)

DD3310 R,160hex Bit <15:4>(ABL thresh hold setting)

- Set ABLOperation Point (Cuve Point)

Item

00

01

02

03

04

05

06

07 08

09

10

11

12

13 14

15 16

17 18

19

20

OS D

PKRD

BRCT

R DRIVE

B DRIVE

G DRIVE

Sub Cont

Lbrm

R Cutoff

B Cutoff

G Cutoff

Sub Brt.

Sub Color

Sub Tint

V Peaking

Svm Gain

Svm Delay

Svm Limit

Ttx Cont

Ttx brt

Pip Cont

Bcl Thrs

Range

0-7

0-1

0-255(X2)

0-12

0-255

0-255 0-255

0-255

0-20(X8)

0-12

0-12 0-63

0-15

0-255

-128-127

0-15

0-255(X8)

29A7

3

0

200

6

180

80 80

80

6

8

4

7

32

5

85

120

15

0

41

Samsung Electronics 4-11

Item

21

22

23 24 25 26

Range

0-255(X2)

0-255(X2) 0-255(X2) 0-255(X2)

0-255

29A7

153

15/25

145 123 204

02

REMARK

DDP3310 R,161hex Bit<8:0>(ABL reduction time constamt setting)

DDP3310 R,162hex Bit<14:6>(ABL curve setting)

-Set the tilt between ABL Operation Point (Curve Point)and MAX BEAM

DDP3310 R,163hex Bit<14:6>(Minimum RGB gain limiter) Peak white drive limit Peak white drive limit tilt point

ABL Cancel Conrtast Increase Time

OSD

Bcl Tc

Bcl Gain

Bcl Mc

Ymax

TB_REL

BCL_TCUP

00 Pal-B/G 00 01 Pal-D/K/L -3 02 Pal-I -3 03 Secam-B/G 03 04 Secam-D/K,L 02 05 Ntsc -1 06 Pal-av 01 07 Secam-av 03 08 Ntsc-av 01

Y.C-Delay

Item

00

01 02 03 04

05 06

07 08

Range

-3~3

29A7

00

-3

-3 03 02

-1

01

03

01

REMARK

VPC3230 FP Sub R, 23hex Bit<11:6> control(FIX)

-Set EEPROM MAP by system separately

-Video: Identified at VPC3230

-Sound: Identified at MSP3410

VPC3230 FP Sub R, 23hex Bit<11:6> control(FIX)

-Set EEPROM MAP by system separately

-Video: Identified at VPC3230

-Sound: Not Identified

OSD

Pal-B/G Pal-D/K/L Pal-I

Secam-B/G Secam-D/K,L

Ntsc Pal-av

Secam-av Ntsc-av

4-12 Samsung Electronics

Deflection Normal

00 01 02 03 04 05 06 07 08 09 10 11 12

13 14 15 16 17 18 19 20 21 22 23 24 25

P. P. P. P. P. P. P. P. P. P. P. P.

P. P. P. P. P. P. P. P. P. P P P P

(N) (N) (N) (N) (N) (N) (N) (N) (N) (N) (N) (N)

V-SIZE V-SFT V-LIN S-CORR EW-WTH EW-PBI H-SFT EW-TPZ BOW ANGLE EW-UPCR EW-LOCR EHT TIME

HOR-EHT VER-EHT EHTVTRS EHTV2 EHTH2 CRNU6 CRNL6 POFS2 HSYNC DLY PHP PVP PHS PVS

20 06 00 45

-71

43/25

24 00 00 00

-12 00 07

-24

-48/90 56 44 95 00 05

-103 93 28 32 00 00

Item

00

01

02

03

04

05

06

07

08

09

10

11

12

13

14

OSD

P.(N)V-Size

P.(N)V-Sft

P.(N)V-Lin

P.(N)S-Corr

P.(N)EW-Wth

P.(N)EW-Pbl

P.(N)H-Sft

P.(N)EW-Tpz

P.(N)Bow

P.(N)Angle

P.(N)EW-UpCr

P.(N)EW-LoCr

EHT Time

P.(N)Hor-EHT

P.(N)Ver-EHT

Range

-128~127(X4)

-128~127

-128~127(X4)

-128~127

0~255(X2)

-128~127(X4)

Initial Value

20

06

00

45

-71(200)

43(-128)

24

00

-12

00

07

-24

-48

Remark

DDP3310 R,14Dhex:VERTICAL SIZE ADJUSTMENT

DDP3310 R,14Fhex:VERTICAL SHIFTADJUSTMENT

DDP3310 R,150hex:VERTICAL LINEARITY ADJUSTMENT

DDP3310 R,151Dhex:VERTICAL S-CORRECTIONADJUSTMENT

DDP3310 R,157hex:HORI.SIZE ADJUSTMENT

DDP3310 R,159hex:HORI.PRABOLAADJUSTMENT

DDP3310 R,144hex:HORI. SHIFT ADJUSTMENT

DDP3310 R,158hex:TRAPEZOID DISTORTION F ACTOR ADJUSTMENT

DDP3310 R,14Bhex:BOW ADJUSTMENT

DDP3310 R,14Ahex:PARALLELGRAM DISTORTION FACTOR ADJUSTMENT

DDP3310 R,15Ahex:UP CONER 1/3 ADJUSTMENT

DDP3310 R,15Bhex:LOW CONER 1/3 ADJUSTMENT

DDP3310 R,15Dhex EHT OPERATION TIME CONSTANT(FIX)

EHT OPERATION AT OVER DDP3310 R,147hex EHTVTRS(FIX)

EHT OPERATION AT OVER DDP3310 R,15Chex EHTVTRS(FIX)

Samsung Electronics 4-13

Item

15

16

17

18

19

20

21

22

23

24

25

OSD

P.(N)EHIVTRS

P.(N)EHTV2

P.(N)EHTH2

P.(N)CRNL6

P.(N)POFS2

P.(N)HSYNC

DLY

P(N)PHP

P(N)PVP

P(N)PHS

P(N)PVS

Range

-128~127(X8)

-128~127(X4)

-128~127

0~255

0~15

Initial Value

56

44

95

00

05

-103

93

28

32

00

Remark

USE THE STEEP CURVE POINT OF HIGH VOLTAGE TO SELECT BOTH EHTAND EHT2 OPERATIONS(FIX)

EHT OPERA TION A T LOW BEAM (less than EHTVTRS)

UP CONER 1/6 ADJUSTEMENT(FIX)

LOW CONER 1/6 ADJUSTEMENT(FIX)

DDP3310 EXT .RGB(PIP,VGA,TTX/OSD)CLAMPING ADJUSTMENT(FIX)

SDP01 HORI. SYNC DELAYADJUSTMENT

-EXT .RGB(PIP ,VGA,TTX/OSD)CLAMPING ADJUSTMENT(FIX)

PIP POSITION ADJUSTMENT

PICTURE POSITION INSIDE PIP ADJUSTMENT(FIX)

Deflection VGA

00 01 02 03 04 05 06 07 08 09 10 11 12

13 14 15 16 17 18 19 20 21 22 23

V-SIZE V-SFT V-LIN S-CORR EW-WTH EW-PBI H-SFT EW-TPZ BOW ANGLE EW-UPCR EW-LOCR EHT TIME

HOR-EHT VER-EHT EHTVTRS EHTV2 EHTH2 CRNU6 CRNL6 POFS2 HSYNC DLY PHP PVP

20 06 00 45

-71 43 24 00 00 00

-12 00 07

-24

-48

255

00 00 05 04 24 93 32 32

4-14 Samsung Electronics

Item

00 01

02 03

04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23

OSD

V-SIZE V-SFT

V-LIN S-CORR EW-WTH

EW-PBI H-SFT

EW-TPZ BOW

ANGLE EW-UPCR EW-LOCR

EHT TIME HOR-EHT

VER-EHT EHTVTRS

EHTV2 EHTH2 CRNU6

CRNL6 POFS2

HSYNCDLY PHP

PVP

Range

-128~127(4X)

-128~127

-128~127(4X)

-128~127

0~255(X2)

-128~127(4X)

-128~127(8X)

-128~127(4X)

-128~127

-128~127 0~255

0~255 0~255

Initial Value

20 06 00 00

-71(200) 43(-128)

24 00 00 00

-12 00 07

-24

-48

255

00 00 05 04 24 93 32 32

Remark

DDP3310 R,14Dhex DDP3310 R,14Fhex

DDP3310 R,150hex DDP3310 R,151hex

DDP3310 R,157hex DDP3310 R,159hex DDP3310 R,144hex DDP3310 R,158hex DDP3310 R,14Bhex DDP3310 R,14Ahex DDP3310 R,15Ahex DDP3310 R,15Bhex DDP3310 R,15Dhex DDP3310 R,147hex DDP3310 R,15Chex

Samsung Electronics 4-15

4-5 3 Speed, Aging mode & Reset mode

1. 3-Speed

1) Speed up Analog Conrtol three times and Time Speed sixty times to let line productivity be improved Analog Control.

2) Enter

- Display + 3Speed Key

3) Cancel

- The 3-Speed mode is cancelled in Master Power Off

- Press the 3Speed Key

4) OSD : The message “3-SPEED” appears on the center of screen

5) No Signal : No AUTO OFF

2. Aging Mode

1) Enter : DISPLAY KEY -> FACTORY KEY (FACTORY MODE)

-> FACTORY KEY (AGING MODE)

- When the AGING mode is entered, the OSD’s are displayed at 100% SIZE WHITE.

- Mute SOUND

2) Cancel

- FACTORY remote conrtol -> Press the FACTORY Key

- LOCAL KEY -> Use the Key MATRIX (Panel Key)

- The AGING mode remains even in MASTER S/W OFF -> ON Cancel the AGING mode only in the above two cases.

3. Factory Reset

1) Run “Reset” on the Factory Menu.

2) Initialize the other user control data except the items that are adjusted in the Factory Mode.

3) Power Off in standby mode.

1. Bus Stop Mode (Use a Micom Stop Pin)

1) Enter the Bus Stop Mode within 200ms when 12c Stop Port is acknowledaged “LOW”.

2) Settings when entering.

- Set the screen mode “STANDARD”.

- Set Bus Line Free.

- Cancal the Bus Stop Mode when 12c Stop Port is acknowledged “High”.

3) Setting when cancelling

- Re-load data from EEPROM and then re-set the appropriate IC.

2. Remot Control Adjustment Mode (Factory Auto Adjustment)

1) Enter the Remote Control Adjustment Mode when the remote control auto adjustment code is input.

2) Settings when entering.

- Set the screen mode “STANDARD”

- Set Bus Line Free.

3) Cancel the Remote Control Adjustment Mode when the usual key code is input.

4) When the code is input, write data in both E2PRM and the appropriate IC within 20ms.

Interval between Code Inputs : 30ms

4-5-1 3-Speed

4-5-2 Bus Stop Mode & Remote Control Adjustment

4-16 Samsung Electronics

4-6 INITIALIZATION DATA DURING RESET

Item Volume Balance Main,Pip Channel Picture Standard Sound Standard Add/erase Channel Sort LNA Color System PIP Position Fine Tune Language Pip,Main Source Digital N/R TILT P-Size PIP-Size

TTX Contrast Child lock Plug & Play

Surround Mode Pro Logic

Intialization Data 10step Center Custom

(Set Value:Standard) Nautral All Channel erased Erased All Channel Off Auto Right under Erased Option byte Selection RF Off

Center Wide:auto,4:3:Normal Big

Factory value All Channel off Option byte Selection Off Normal

Item TV Power Blue Screen TINT Still Picture AV Setup Time On/Off Time H/P Volume H/P Bal.,Tbl,Bass Programe naming Audio out Int.mute Center,Rear Volume Zoom Lift PC Screen Shift Country

Initialization Data Stand by On Center Cancel Ext2,Ext3:RF

- - : - -

- - : - 10 Step Center

All Channel Erased(*) Volume out Off Center Center Center Austria

Samsung Electronics 4-17

4-7 CHASSIS FUNTION

P

I C T U R E

PIP

FUNTION LINE FLICKERLESS LARGE AREA FLICKERLESS MOTION DETECTOR MAIN STILL PICTURE ZOOM FUNCTION (4:3,WIDE CRT OPTION) ZOOM LIFT DIGITAL N/R COMB FILTER CTI SCAN MODE P-STD COLOR TONE DYNAMIC-FOCUS VM TILT CONTROL VGA DVD MULTI PIP LNA ON/OFF SWAP,ROTATE,SIZE,SCAN

PAL YES YES YES YES NORMAL -> 16:9 -> ZOOM

AUTO WIDE->P ANORAMA->4:3->16:9->ZOOM1->ZOOM2

YES YES 4H DIGIT ALCTI

NA TURALSCAN -> DIGITALSCAN -> PORGRESSIVE SCAN

CUSTOM->ST ANDARD->SPORTS->MILD->NATURAL NORMAL -> WARM1- > WARM2 -> COOL1 -> COOL2

YES YES YES YES RCAJACK MODELONLY -> YUV MODE YES YES YES

4-18 Samsung Electronics

FUNTION ATM PLUG & PLAY AV LINK TTX OSD TYPE

SLEEP TIMER ON/OFF TIMER CHILD LOCK

PROGRAMMABLE CH. TUNING SYSTEM SORT & NAME INFORMATION ADD/ERASE DOLBY PROLOGIC A2 STEREO EQUALIZER NICAM STEREO OUTPUT (MPO) S-STD

HEADPHONE VOLUME CONTROL

FRONT

REAR

PAL ATM(EU) YES SCART JACK MODELONL Y(SCART1) MEGATEXT OSG YES YES YES 100 CH. MENORY PROGRAMMABLE F/S YES YES(NAME,SOUND MODE,CHILD LOCK) YES(CHANNEL SKIP) YES YES YES YES MAIN:12+12W, SUR:12+12W, CENTER:12W CUSTOM->ST ANDARD->MUSIC->MOVIE->SPEECH YES

1 S-VHS,1RCAINPUT,1HEADPHONE,1 VGA SCART JACK MODEL: 1RF,3SCART,DOLBY JACK RCAJACK MODEL:1RF,1 S-VHS,3RCA IN, 1DVD IN,

1 MONITOR OUT, DOLBY JACK

P U N

T

I

O

N

EXT

JACK

S

O

U

N

D